Remove 'num_trbs' from 'xhci_td' as it's no longer used following the
removal of 'num_trbs_free' tracking in commit 2710f8186f ("xhci: Stop
unnecessary tracking of free trbs in a ring").
Tracking of 'num_trbs_free' is still performed in xhci DbC, but it does not
utilize 'num_trbs'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-3-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple streams are in use, multiple TDs might be in flight when
an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for
each, to ensure everything is reset properly and the caches cleared.
Change the logic so that any N>1 TDs found active for different streams
are deferred until after the first one is processed, calling
xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to
queue another command until we are done with all of them. Also change
the error/"should never happen" paths to ensure we at least clear any
affected TDs, even if we can't issue a command to clear the hardware
cache, and complain loudly with an xhci_warn() if this ever happens.
This problem case dates back to commit e9df17eb14 ("USB: xhci: Correct
assumptions about number of rings per endpoint.") early on in the XHCI
driver's life, when stream support was first added.
It was then identified but not fixed nor made into a warning in commit
674f8438c1 ("xhci: split handling halted endpoints into two steps"),
which added a FIXME comment for the problem case (without materially
changing the behavior as far as I can tell, though the new logic made
the problem more obvious).
Then later, in commit 94f339147f ("xhci: Fix failure to give back some
cached cancelled URBs."), it was acknowledged again.
[Mathias: commit 94f339147f ("xhci: Fix failure to give back some cached
cancelled URBs.") was a targeted regression fix to the previously mentioned
patch. Users reported issues with usb stuck after unmounting/disconnecting
UAS devices. This rolled back the TD clearing of multiple streams to its
original state.]
Apparently the commit author was aware of the problem (yet still chose
to submit it): It was still mentioned as a FIXME, an xhci_dbg() was
added to log the problem condition, and the remaining issue was mentioned
in the commit description. The choice of making the log type xhci_dbg()
for what is, at this point, a completely unhandled and known broken
condition is puzzling and unfortunate, as it guarantees that no actual
users would see the log in production, thereby making it nigh
undebuggable (indeed, even if you turn on DEBUG, the message doesn't
really hint at there being a problem at all).
It took me *months* of random xHC crashes to finally find a reliable
repro and be able to do a deep dive debug session, which could all have
been avoided had this unhandled, broken condition been actually reported
with a warning, as it should have been as a bug intentionally left in
unfixed (never mind that it shouldn't have been left in at all).
> Another fix to solve clearing the caches of all stream rings with
> cancelled TDs is needed, but not as urgent.
3 years after that statement and 14 years after the original bug was
introduced, I think it's finally time to fix it. And maybe next time
let's not leave bugs unfixed (that are actually worse than the original
bug), and let's actually get people to review kernel commits please.
Fixes xHC crashes and IOMMU faults with UAS devices when handling
errors/faults. Easiest repro is to use `hdparm` to mark an early sector
(e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop.
At least in the case of JMicron controllers, the read errors end up
having to cancel two TDs (for two queued requests to different streams)
and the one that didn't get cleared properly ends up faulting the xHC
entirely when it tries to access DMA pages that have since been unmapped,
referred to by the stale TDs. This normally happens quickly (after two
or three loops). After this fix, I left the `cat` in a loop running
overnight and experienced no xHC failures, with all read errors
recovered properly. Repro'd and tested on an Apple M1 Mac Mini
(dwc3 host).
On systems without an IOMMU, this bug would instead silently corrupt
freed memory, making this a security bug (even on systems with IOMMUs
this could silently corrupt memory belonging to other USB devices on the
same controller, so it's still a security bug). Given that the kernel
autoprobes partition tables, I'm pretty sure a malicious USB device
pretending to be a UAS device and reporting an error with the right
timing could deliberately trigger a UAF and write to freed memory, with
no user action.
[Mathias: Commit message and code comment edit, original at:]
https://lore.kernel.org/linux-usb/20240524-xhci-streams-v1-1-6b1f13819bea@marcan.st/
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Fixes: 94f339147f ("xhci: Fix failure to give back some cached cancelled URBs.")
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print the full hex value of PORTSC register in addition to the human
readable decoded string while debugging PORTSC value.
If PORTSC value is 0xffffffff then don't decode it.
This lets us inspect Rsvd bits of PORTSC.
Same is done for USBSTS register values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'erst_size' represents the maximum capacity of entries that ERST can hold,
while 'num_entries' indicates the actual number of entries currently held
in the ERST. These two values are identical because the xhci driver does
not support ERST expansion. Thus, 'erst_size' is removed.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables real & fake port do not convey their purpose, thus they are
replaced with a pointer to the root hub port 'struct xhci_port *rhub_port'.
'rhub_port' contains real & fake ports in zero-based format, which happens
to be more widely used inside the xHCI driver:
- 'real_port' is ('rhub_port->hw_portnum' + 1)
- 'fake_port' is ('rhub_port->hcd_portnum' + 1)
One reason for real port being one-based, is to signal other functions in
case struct 'xhci_virt_device' initialization failed, in this case the
value will remain 0. This is no longer needed, instead we check whether
or not 'rhub_port' is 'NULL'.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of variable 'msix_count' containing the number of MSI-X vectors,
now it can contains MSI or MSI-X vector amount. Because both interrupt
methods allow several vectors. Thus, 'msix_count' is renamed to 'nvecs'.
Additionally, instead of storing the maximum possible vector amount,
now it stores the amount of successfully allocated vectors, or negative
integer on allocation failure.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for new
hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio, spi,
and i2c drivers for that type of device (all acked by the respective
subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems, EXCEPT for some merge conflicts that you will run
into in your tree. 2 of them are in device-tree files, which will be
trivial to resolve (accept both sides), and the last in the
drivers/gpio/gpio-ljca.c file, in the remove callback, resolution should
be pretty trivial (take the version in this branch), see here:
https://lore.kernel.org/all/20231016134159.11d8f849@canb.auug.org.au/
for details, or I can provide a resolved merge point if needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUStew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxgQCggUyfGo+JVV8XZVu5A9KwT6nr7mUAmwUgFxhZ
khK77t0KqF4hjXryeaHa
=iPd+
-----END PGP SIGNATURE-----
Merge tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAmU/3cUWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJsEoEACBGPSiOmfSWdH3TOnIG270PD24
jGjg8KFv7RC/JTOdYmpLl0okdlGT9LvjN/ToSSDEw3PIayxoXUdhkbYy0MYtiV3m
yz2ozDTzJuplQX/W2fPE+nXSzIwHao2zjPPFjHnT7lt8IIjhgjiOtLfZ2gGUkW99
Mdu2aWh3u0r4tC8OS23++yN5ibRc5l72efsjDWjZ0aPXnxE1bjmLMiIPiizpndIf
beasPuDBs98sJVYouemCwnsPXuXOPz3Q1Cpo/fTd+TMTJCLSemCQZCTuOBU0acI/
ZjLCgCaJU1yIYKBMtrIN4G9kITZniXX3/Nm4o6NQMVlcCqMeNaHuflomqWoqWfhE
UPbRo2eghZOaMNiCKLLvZDIqPrh1IcsiEl6Ef3W4hICc42GTK96IuGisIvDXwQ4N
/SzTOupJuN42noh3z1M3XuZy5RoXJ99IYDNY5CTKf9IdqvA0bbGkU3nb1gZH/xw9
BjTqKzR/7K1kTXuSgagDZ1Wceej9pZxhX7E3IHYsP8ZOvKug3EeL4yybVwQ3HRfq
Qnzcp/qPB9cOkLSQXveRTFTsj2mX28Gixct/iDuc1jIYwGQlY1gI6dcUcqby6ptM
BrQti7eR2NH2+T3aE2UVCIWsZVhx7NaSF+z8JxfAuu56jicc4xJVsi8zrNveWX5M
m2VXyBl3121BVtKi4w==
=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_alloc_erst() has global scope even though it's only used in
xhci-mem.c. Declare it static.
xhci_free_erst() was removed by commit b17a57f89f ("xhci: Refactor
interrupter code for initial multi interrupter support."), but a
declaration in xhci.h still remains. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ebd88cf507 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias notes that the ERST_PTR_MASK macro is named as if it's masking
the Event Ring Dequeue Pointer in the ERDP register, but in actuality
it's masking the inverse.
Invert the macro's value for clarity.
Migrate it to the modern GENMASK_ULL() syntax to avoid u64 casts.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct urb_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20230915195812.never.371-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 driver needs access to XHCI Extended Capabilities registers to
read number of usb2 ports and usb3 ports present on multiport controller.
Since the extcaps header is sufficient to parse this info, move port_count
related macros and structure from xhci.h to xhci-ext-caps.h.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20230828133033.11988-4-quic_kriskura@quicinc.com
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to keep track of free trbs in a ring by adding and subtracting
deltas each time a enqueue or dequeue is increased or moved has proven to
be buggy and complicated, especially over long periods of time.
Recently a bug in counting free trbs was fixed, now taking into account
cancelled URBs that were turned into no-ops, preventing free_trbs to
slowly wander off causing unnecessary ring expansion. See
commit fe82f16aaf ("xhci: Fix incorrect tracking of free space on
transfer rings")
Turns out its a lot easier to just calculate the numer of free TRB
based on ring size and the current enqueue and dequeue pointer values.
This is currently only needed for the command ring as multi segment
transfer rings already ensures there is enough room the ring during
the ring expansion check.
We could get rid of the ring->num_trbs_free entry completely, but as
the xhci DbC code also uses it we don't clean that up in this patch.
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-8-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_PLAT quirk was only needed to ensure non-PCI xHC host avoided
setting up MSI interrupts in generic xhci codepaths.
The MSI setup code is now moved to PCI specific xhci-pci.c file so
the quirk is no longer needed.
Remove setting the XHCI_PLAT quirk for HiSilocon SoC xHC, NVIDIA Tegra xHC,
MediaTek xHC, the generic xhci-plat driver, and the checks for XHCI_PLAT
in xhci-pci.c MSI setup code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-5-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves merge conflicts in:
drivers/usb/dwc3/gadget.c
drivers/usb/gadget/udc/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Donghun reports that a notebook that has an AMD Ryzen 5700U but supports
S3 has problems with USB after resuming from suspend. The issue was
bisected down to commit d1658268e4 ("usb: pci-quirks: disable D3cold on
xhci suspend for s2idle on AMD Renoir").
As this issue only happens on S3, narrow the broken D3cold quirk to only
run in s2idle.
Fixes: d1658268e4 ("usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir")
Reported-and-tested-by: Donghun Yoon <donghun.yoon@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the pci_resume method has only a flag indicating whether the
system is resuming from hibernation. In order to handle all PM events like
AUTO_RESUME (runtime resume from device in D3), RESUME (system resume from
s2idle, S3 or S4 states) etc change the pci_resume method to handle all PM
events.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-2-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move function to cleanup MSI from xhci.c to xhci-pci.c
This is to decouple PCI specific code from generic xhci code.
No functional changes, function is an exact copy
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call the PCI specific MSI/MSIX interrupt freeing code from the xhci-pci
callbacks instead of generic xhci code, decoupling PCI parts from
generic xhci functions.
Adds xhci_pci_stop() that overrides xhci_stop() for PCI xHC controllers.
This will free MSIX interrupts a bit later in the hc_driver stop
callback, but is still earlier than usb core frees "legacy" interrupts,
or interrupts for other hosts.
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move functions to setup msi from xhci.c to xhci-pci.c to decouple
PCI specific code from generic xhci code.
No functional changes, functions are an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci MSI setup is currently done at the same time as xHC host is started
in xhci_run(). This couples the generic xhci code with PCI, and will
reconfigure MSI/MSIX interrupts every time xHC is started.
Decouple MSI/MSIX configuration from generic xhci code by moving MSI/MSIX
part to a PCI specific xhci_pci_run() function overriding xhci_run().
This allows us to remove unnecessay MSI/MSIX reconfiguration done every
time PCI xhci resumes from suspend. i.e. remove the xhci_cleanup_msix()
call from xhci_resume() and the xhci_try_enale_msi() call in xhci_run()
called a bit later by xhci_resume()
[minor changes and commit message rewrite -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
resume_done is just a timestamp, avoid confusing it with completions
related to port state transitions that are named *_done
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a port structure for each port it makes sense to
move per port variables, timestamps and completions there.
Get rid of storing bitfileds and arrays of port specific items per bus.
Move
unsigned long resume_done;
insigned long rexit_ports
struct completion rexit_done;
struct completion u3exit_done;
Rename rexit_ports to rexit_active, and remove a redundant hcd
speed check while checking if rexit_active is set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC supports several interrupters, each with its own mmio register set,
event ring and MSI/MSI-X vector. Transfers can be assigned different
interrupters when queued. See xhci 4.17 for details.
Current driver only supports one interrupter.
Create a xhci_interrupter structure containing an event ring, pointer to
mmio registers for this interrupter, variables to store registers over s3
suspend, erst, etc. Add functions to create and free an interrupter, and
pass an interrupter pointer to functions that deal with events.
Secondary interrupters are also useful without having an interrupt vector.
One use case is the xHCI audio sideband offloading where a DSP can take
care of specific audio endpoints.
When all transfer events of an offloaded endpoint can be mapped to a
separate interrupter event ring the DSP can poll this ring, and we can mask
these events preventing waking up the CPU.
Only minor functional changes such as clearing some of the interrupter
registers when freeing the interrupter.
Still create only one primary interrupter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC controller can supports up to 1024 interrupters.
To fit these change the max_interrupters varable from u8 to u16.
Add a separate mask for the reserve and preserve bits [5:0] in the erst
base register and use it instead of the ERST_PRT_MASK.
ERSR_PTR_MASK [3:0] is intended for masking bits in the
event ring dequeue pointer register.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves merge conflicts as
reported in linux-next in the following files:
drivers/usb/host/xhci.c
drivers/usb/host/xhci.h
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a hub_control() callback to the xhci_driver_overrides structure to
allow host drivers to override the default hub_control function. This
is required for Tegra which requires device specific actions for power
management to be executed during USB state transitions.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-2-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci used to test if link power management (LPM) capable USB2 devices
really could enter and exit L1 state link state.
Failed devices were added to a lpm_failed_dev list.
This feature was removed 9 years ago in
commit de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.")
but lpm_failed_dev member was still left.
Remove it now.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The u32 command was added to struct xhci_hcd over 10 years ago in
commit 9777e3ce90 ("USB: xHCI: bus power management implementation")
It wasn't even used back then, so remove it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 83810f84ec.
Turning off port power in shutdown did cause issues such as a laptop not
proprly powering off, and some specific usb devies failing to enumerate the
subsequent boot after a warm reset.
So revert this.
Fixes: 83810f84ec ("xhci: turn off port power in shutdown")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
apparently missed one sprintf() call in xhci_decode_trb() -- replace
it with the snprintf() call as well...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Fixes: cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220630124645.1805902-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c950686b38 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want those around confusing people.
ERST_NUM_SEGS is used both when allocating event ring segments, and when
allocating entries in the event ring segment table (erst).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call onboard_hub_create/destroy_pdevs() from _probe()/_remove()
to create/destroy platform devices for onboard USB hubs that may
be connected to the root hub of the controller. These functions
are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct xhci_hcd to keep track of the onboard hub
platform devices that are owned by the xHCI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.4.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of re-reading, masking and endianness correcting the same trb
several times to get the trb type from an event, just do it once and
store it in a local variable.
Also pass the trb_type directly to the vendor specific event handler,
avoiding one more similar read.
In addition to the security benefit this also cleans up the code
and helps readability.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When finishing a TD we walk the endpoint dequeue trb pointer
until it matches the last TRB of the TD.
TDs can contain over 100 TRBs, meaning we call a function 100 times,
do a few comparisons and increase a couple values for each of these calls,
all in interrupt context.
This can all be avoided by adding a pointer to the last TRB segment, and
a number of TRBs in the TD. So instead of walking through each TRB just
set the new dequeue segment, pointer, and number of free TRBs directly.
Getting rid of the while loop also reduces the risk of getting stuck in a
infinite loop in the interrupt handler. Loop relied on valid matching
dequeue and last_trb values to break.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The one case that used this function can use the
xhci_triad_to_transfer_ring() helper instead.
Avoid having several functions doing basically the same thing.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.
Add a helper for this, check that slot_id and ep_index are valid.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some atypical users of xhci-pci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-6-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic xhci ring allocations code needs struct xhci_hcd pointer, and
it allocates memory for the rings from dma pools created for the xhci
device.
In order to decouple xhci and DbC we have to create our own ring allocation
and free routines for DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EP_STATE_MASK should be 0x7 instead of 0xf
xhci spec 6.2.3 shows that the EP state field in the endpoint context data
structure consist of bits [2:0].
The old value included a bit from the next field which fortunately is a
RsvdZ region. So hopefully this hasn't caused too much harm
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some rensas controller like uPD720201 and uPD720202 need firmware to be
loaded. Add these devices in table and invoke renesas firmware loader
functions to check and load the firmware into device memory when
required.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-4-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
