On Google gs101, the number of UTP transfer request slots (nutrs) is 32,
and in this case the driver ends up programming the UTRL_NEXUS_TYPE
incorrectly as 0.
This is because the left hand side of the shift is 1, which is of type
int, i.e. 31 bits wide. Shifting by more than that width results in
undefined behaviour.
Fix this by switching to the BIT() macro, which applies correct type
casting as required. This ensures the correct value is written to
UTRL_NEXUS_TYPE (0xffffffff on gs101), and it also fixes a UBSAN shift
warning:
UBSAN: shift-out-of-bounds in drivers/ufs/host/ufs-exynos.c:1113:21
shift exponent 32 is too large for 32-bit type 'int'
For consistency, apply the same change to the nutmrs / UTMRL_NEXUS_TYPE
write.
Fixes: 55f4b1f736 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250707-ufs-exynos-shift-v1-1-1418e161ae40@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Peter Griffin <peter.griffin@linaro.org> says:
Hi folks,
This series fixes several stability issues with the upstream ufs-exynos
driver, specifically for the gs101 SoC found in Pixel 6.
The main fix is regarding the IO cache coherency setting and ensuring
that it is correctly applied depending on if the dma-coherent property
is specified in device tree. This fixes the UFS stability issues on gs101
and I would imagine will also fix issues on exynosauto platform that
seems to have similar iocc shareability bits.
Additionally the phy reference counting is fixed which allows module
load/unload to work reliably and keeps the phy state machine in sync
with the controller glue driver.
regards,
Peter
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-0-96722cc2ba1b@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GPIO_OUT[0] is connected to the reset pin of embedded UFS device.
Before powering off the phy assert the reset signal.
This is added as a gs101 specific suspend hook so as not to have any
unintended consequences for other SoCs supported by this driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-7-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_pltfrm_remove() calls ufshcd_remove(hba) which in turn calls
ufshcd_hba_exit().
By moving the phy_power_off() and phy_exit() calls to the newly created
.exit callback they get called by ufshcd_variant_hba_exit() before
ufshcd_hba_exit() turns off the regulators. This is also similar flow to
the ufs-qcom driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-6-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PRDT_PREFETCH_ENABLE[31] bit should be set when desctype field of
fmpsecurity0 register is type2 (double file encryption) or type3
(support for file and disk encryption). Setting this bit enables PRDT
pre-fetching on both TXPRDT and RXPRDT.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-5-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_link_startup() can call ufshcd_vops_link_startup_notify()
multiple times when retrying. This causes the phy reference count to
keep increasing and the phy to not properly re-initialize.
If the phy has already been previously powered on, first issue a
phy_power_off() and phy_exit(), before re-initializing and powering on
again.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-4-96722cc2ba1b@linaro.org
Fixes: 3d73b200f9 ("scsi: ufs: ufs-exynos: Change ufs phy control sequence")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If dma-coherent property isn't set then descriptors are non-cacheable
and the iocc shareability bits should be disabled. Without this UFS can
end up in an incompatible configuration and suffer from random cache
related stability issues.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Fixes: cc52e15397 ("scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-3-96722cc2ba1b@linaro.org
Cc: Chanho Park <chanho61.park@samsung.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gs101 I/O coherency shareability bits differ from exynosauto SoC. To
support both SoCs move this info the SoC drvdata.
Currently both the value and mask are the same for both gs101 and
exynosauto, thus we use the same value.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-2-96722cc2ba1b@linaro.org
Fixes: d11e0a318d ("scsi: ufs: exynos: Add support for Tensor gs101 SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ensure clocks are enabled before configuring unipro. Additionally move
the pre_link() hook before the exynos_ufs_phy_init() calls. This means
the register write sequence more closely resembles the ordering of the
downstream driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-1-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash. The only non-trivial core change
is an addition to unit attention handling to recognize UAs for power
on/reset and new media so the tape driver can use it.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ+RQ2yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishe6DAQCdW/21
S1Y6BDlJLQfpWChGv6GIzanC+5sMfylw4d6ULgEA8upOE5L3fC29IY958jXig0o1
uLjxylwYEfVLDf8gwJ0=
=mkM+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash.
The only non-trivial core change is an addition to unit attention
handling to recognize UAs for power on/reset and new media so the tape
driver can use it"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (107 commits)
scsi: st: Tighten the page format heuristics with MODE SELECT
scsi: st: ERASE does not change tape location
scsi: st: Fix array overflow in st_setup()
scsi: target: tcm_loop: Fix wrong abort tag
scsi: lpfc: Restore clearing of NLP_UNREG_INP in ndlp->nlp_flag
scsi: hisi_sas: Fixed failure to issue vendor specific commands
scsi: fnic: Remove unnecessary NUL-terminations
scsi: fnic: Remove redundant flush_workqueue() calls
scsi: core: Use a switch statement when attaching VPD pages
scsi: ufs: renesas: Add initialization code for R-Car S4-8 ES1.2
scsi: ufs: renesas: Add reusable functions
scsi: ufs: renesas: Refactor 0x10ad/0x10af PHY settings
scsi: ufs: renesas: Remove register control helper function
scsi: ufs: renesas: Add register read to remove save/set/restore
scsi: ufs: renesas: Replace init data by init code
scsi: ufs: dt-bindings: renesas,ufs: Add calibration data
scsi: mpi3mr: Task Abort EH Support
scsi: storvsc: Don't report the host packet status as the hv status
scsi: isci: Make most module parameters static
scsi: megaraid_sas: Make most module parameters static
...
The third pwr_change_notify() argument is an input parameter. Make this
explicit by declaring it 'const'.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20250212213838.1044917-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To prevent keys from being compromised if an attacker acquires read
access to kernel memory, some inline encryption hardware can accept keys
which are wrapped by a per-boot hardware-internal key. This avoids
needing to keep the raw keys in kernel memory, without limiting the
number of keys that can be used. Such hardware also supports deriving a
"software secret" for cryptographic tasks that can't be handled by
inline encryption; this is needed for fscrypt to work properly.
To support this hardware, allow struct blk_crypto_key to represent a
hardware-wrapped key as an alternative to a raw key, and make drivers
set flags in struct blk_crypto_profile to indicate which types of keys
they support. Also add the ->derive_sw_secret() low-level operation,
which drivers supporting wrapped keys must implement.
For more information, see the detailed documentation which this patch
adds to Documentation/block/inline-encryption.rst.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # sm8650
Link: https://lore.kernel.org/r/20250204060041.409950-2-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Updates to the usual drivers (ufs, lpfc, hisi_sas, st). Amazingly
enough, no core changes with the biggest set of driver changes being
ufs (which conflicted with it's own fixes a bit, hence the merges) and
the rest being minor fixes and updates.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ0SFmyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdA6AQC+yzhe
jx0+EBw1RkjRoT6vapBsjN8Sc1rOr/8+TuJ8KwEA0eVuXSiFEx/ieeKLD2VuE6y4
NPRB36MZdOxfQaDZAY4=
=Fj/G
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, hisi_sas, st).
Amazingly enough, no core changes with the biggest set of driver
changes being ufs (which conflicted with it's own fixes a bit, hence
the merges) and the rest being minor fixes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
scsi: st: New session only when Unit Attention for new tape
scsi: st: Add MTIOCGET and MTLOAD to ioctls allowed after device reset
scsi: st: Don't modify unknown block number in MTIOCGET
scsi: ufs: core: Restore SM8650 support
scsi: sun3: Mark driver struct with __refdata to prevent section mismatch
scsi: sg: Enable runtime power management
scsi: qedi: Fix a possible memory leak in qedi_alloc_and_init_sb()
scsi: qedf: Fix a possible memory leak in qedf_alloc_and_init_sb()
scsi: fusion: Remove unused variable 'rc'
scsi: bfa: Fix use-after-free in bfad_im_module_exit()
scsi: esas2r: Remove unused esas2r_build_cli_req()
scsi: target: Fix incorrect function name in pscsi_create_type_disk()
scsi: ufs: Replace deprecated PCI functions
scsi: Switch back to struct platform_driver::remove()
scsi: pm8001: Increase request sg length to support 4MiB requests
scsi: pm8001: Initialize devices in pm8001_alloc_dev()
scsi: pm8001: Use module param to set pcs event log severity
scsi: ufs: ufs-mediatek: Configure individual LU queue flags
scsi: MAINTAINERS: Update UFS Exynos entry
scsi: lpfc: Copyright updates for 14.4.0.6 patches
...
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
Hi,
This series has several bug fixes that I encountered when the ufs-qcom driver
was removed and inserted back. But the fixes are applicable to other platform
glue drivers as well.
This series is tested on Qcom RB5 development board based on SM8250 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-0-45ad8b62f02e@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During the remove stage of glue drivers, some of them are incrementing the
reference count using pm_runtime_get_sync(), before removing the ufshcd
using ufshcd_remove(). But they are not dropping that reference count after
ufshcd_remove() to balance the refcount.
So drop the reference count by calling pm_runtime_put_noidle() after
ufshcd_remove(). Since the behavior is applicable to all glue drivers, move
the PM handling to ufshcd_pltfrm_remove().
Cc: stable@vger.kernel.org # 3.12
Fixes: 62694735ca ("[SCSI] ufs: Add runtime PM support for UFS host controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-4-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the UFSHCD platform glue drivers are removed, runtime PM should be
disabled using pm_runtime_disable() to balance the enablement done in
ufshcd_pltfrm_init(). This is also reported by PM core when the glue driver
is removed and inserted again:
ufshcd-qcom 1d84000.ufshc: Unbalanced pm_runtime_enable!
So disable runtime PM using a new helper API ufshcd_pltfrm_remove(), that
also takes care of removing ufshcd. This helper should be called during the
remove() stage of glue drivers.
Cc: stable@vger.kernel.org # 3.12
Fixes: 62694735ca ("[SCSI] ufs: Add runtime PM support for UFS host controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-3-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/ufs to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241119182856.55743-2-u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable clock gating and hibern8 capabilities for gs101. This leads to a
significantly cooler phone when running the upstream kernel.
The exynos_ufs_post_hibern8() hook is also updated to remove the
UIC_CMD_DME_HIBER_EXIT code path as this causes a hang on gs101.
The code path is removed rather than re-factored as no other SoC in
ufs-exynos driver sets UFSHCD_CAP_HIBERN8_WITH_CLK_GATING
capability. Additionally until the previous commit the hibern8 callbacks
were broken anyway as they expected a bool.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-14-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
HCI_IOP_ACG_DISABLE is an undocumented register in the TRM but the
downstream driver sets this register so we follow suit here.
The register is already 0 presumed to be set by the bootloader as the
comment downstream implies the reset state is 1. So whilst this is a nop
currently, it should protect us in case the bootloader behaviour ever
changes.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-12-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently just AXIDMA_RWDATA_BURST_LEN[3:0] field is set to 8 in
exynos_ufs_post_link() function.
To enable WLU transaction additionally we need to set Write Line Unique
enable [31], Write Line Unique Burst Length [30:27] and
AXIDMA_RWDATA_BURST_LEN[3:0].
To support WLU transaction on gs101, both burst length fields need to be
0x3. As all other SoCs expect the current value we update this in the
gs101_ufs_post_link() specific hook.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-11-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Factor out the common code into a new exynos_ufs_shareability() function
and provide a dedicated gs101_drv_init() hook.
This allows us to enable WriteBooster capability (UFSHCD_CAP_WB_EN) in a
way that doesn't effect other SoCs supported in this driver.
WriteBooster improves write speeds by enabling a pseudo SLC cache. Using
the 'fio seqwrite' test we can achieve speeds of 945MB/s with this
feature enabled (until the cache is exhausted) before dropping back to
~260MB/s (which are the speeds we see without the WriteBooster feature
enabled).
Assuming the UFSHCD_CAP_WB_EN capability is set by the host then
WriteBooster can also be enabled and disabled via sysfs so it is
possible for the system to only enable it when extra write performance
is required.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-10-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the assignment of tx_dif_p_nsec as both users of
exynosauto_ufs_drv_init() function (exynosauto and gs101) set the
EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR flag meaning that tx_dif_p_nsec has
no effect.
Additionally both users also set the samsung,sysreg dt property, meaning
the execution flow will always return on the regmap_update_bits() call
before the assignment.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-9-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that exynos_ufs_specify_phy_time_attr() checks the appropriate
EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR flag. Remove the unused fields in
gs101_uic_attr.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-8-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The values calculated in exynos_ufs_specify_phy_time_attr() are only
used in exynos_ufs_config_phy_time_attr() which is only called if the
EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR flag is not set.
Add a check for this flag to exynos_ufs_specify_phy_time_attr() and
return for platforms that don't set it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-7-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Auto clk control works fine for gs101, so remove
EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL flag.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-6-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the EXYNOS_UFS_OPT_UFSPR_SECURE check inside
exynos_ufs_config_smu().
This way all call sites will benefit from the check. This fixes a bug
currently in the exynos_ufs_resume() path on gs101 as it calls
exynos_ufs_config_smu() and we end up accessing registers that can only
be accessed from secure world which results in a serror.
Fixes: d11e0a318d ("scsi: ufs: exynos: Add support for Tensor gs101 SoC")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-5-peter.griffin@linaro.org
Cc: stable@vger.kernel.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS Gear 4 offers faster speeds, and better power usage so lets enable
it.
Currently ufshcd_init_host_params() sets UFS_HS_G3 as a default, so even
if the device supports G4 we end up negotiating down to G3.
For SoCs like gs101 which have a UFS major controller version of 3 or
above advertise Gear 4. This then allows a Gear 4 link on Pixel 6.
For earlier controller versions keep the current default behaviour of
reporting G3.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-4-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer to device can be obtained from ufs->hba->dev, remove
superfluous function parameter.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-3-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove empty method. When the method is not set, the call is not made,
saving a few cycles.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-2-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
If exynos_ufs_fmp_init() did not enable FMP support, then
exynos_ufs_fmp_resume() should not execute the FMP-related SMC calls.
Fixes: c96499fcb4 ("scsi: ufs: exynos: Add support for Flash Memory Protector (FMP)")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20240721183840.209284-1-ebiggers@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Flash Memory Protector (FMP), which is the inline
encryption hardware on Exynos and Exynos-based SoCs.
Specifically, add support for the "traditional FMP mode" that works on many
Exynos-based SoCs including gs101. This is the mode that uses "software
keys" and is compatible with the upstream kernel's existing inline
encryption framework in the block and filesystem layers. I plan to add
support for the wrapped key support on gs101 at a later time.
Tested on gs101 (specifically Pixel 6) by running the 'encrypt' group of
xfstests on a filesystem mounted with the 'inlinecrypt' mount option.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20240708235330.103590-7-ebiggers@kernel.org
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Peter Griffin <peter.griffin@linaro.org> says:
Hi Martin, James & Alim,
This series adds support to the ufs-exynos driver for Tensor gs101
found in Pixel 6. It was send previously in [1] and [2] but included
the other clock, phy and DTS parts. This series has been split into
just the ufs-exynos part to hopefully make things easier.
With this series, plus the phy, clock and dts changes UFS is
functional upstream for Pixel 6. The SKhynix HN8T05BZGKX015 can be
enumerated, partitions mounted etc.
The series is split into some prepatory patches for ufs-exynos and a
final patch that adds the gs101 support.
Note the sysreg clock has been moved to ufs node as fine grained clock
control around the syscon sysreg register accesses doesn't result in
functional UFS.
regards,
Peter
Link: https://lore.kernel.org/r/20240426122004.2249178-1-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a dedicated compatible and drv_data with associated hooks for gs101 SoC
found on Pixel 6.
Note we make use of the previously added EXYNOS_UFS_OPT_UFSPR_SECURE
option, to skip initialisation of UFSPR registers as these are only
accessible via SMC call.
EXYNOS_UFS_OPT_TIMER_TICK_SELECT option is also set to select tick
source. This has been done so as not to effect any existing platforms.
DBG_OPTION_SUITE on gs101 has different address offsets to other SoCs so
these register offsets now come from uic_attr struct.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-7-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows these registers to be at different offsets or not exist at all
on some SoCs variants.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-6-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This option is intended to be set for SoCs that have HCI_V2P1_CTRL register
and can select their tick source via IA_TICK_SEL bit.
Source clock selection for timer tick
0x0 = Bus clock (aclk)
0x1 = Function clock (mclk)
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-4-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This option is intended to be set on platforms whose ufspr registers are
only accessible via smc call (such as gs101).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-3-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig <hch@lst.de> says:
Hi all,
this series converts the SCSI midlayer and LLDDs to use atomic queue
limits API. It is pretty straight forward, except for the mpt3mr
driver which does really weird and probably already broken things by
setting limits from unlocked device iteration callbacks.
I will probably defer the (more complicated) ULD changes to the next
merge window as they would heavily conflict with Damien's zone write
plugging series. With that the series could go in through the SCSI
tree if Jens' ACKs the core block layer bits.
Link: https://lore.kernel.org/r/20240409143748.980206-1-hch@lst.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export the module alias information using the MODULE_DEVICE_TABLE() macro
in order to support auto-loading this module for devices that support it.
$ modinfo -F alias out/linux/drivers/ufs/host/ufs-exynos.ko
of:N*T*Ctesla,fsd-ufsC*
of:N*T*Ctesla,fsd-ufs
of:N*T*Csamsung,exynosautov9-ufs-vhC*
of:N*T*Csamsung,exynosautov9-ufs-vh
of:N*T*Csamsung,exynosautov9-ufsC*
of:N*T*Csamsung,exynosautov9-ufs
of:N*T*Csamsung,exynos7-ufsC*
of:N*T*Csamsung,exynos7-ufs
Signed-off-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240409202203.1308163-1-willmcvicker@google.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the SCSI host's dma_alignment field and set it in ->init and remove the
now unused config_scsi_dev method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-9-hch@lst.de
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Structure ufs_dev_params is actually used in UFS host drivers to declare
host specific power mode parameters, like ufs_<vendor>_params or host_cap,
which makes the code not very straightforward to read. Rename the structure
ufs_dev_params to ufs_host_params and unify the declarations in all drivers
to host_params.
In addition, rename the two functions ufshcd_init_pwr_dev_param() and
ufshcd_get_pwr_dev_param() which work based on the ufs_host_params to
ufshcd_init_host_params() and ufshcd_negotiate_pwr_params() respectively to
avoid confusions.
This change does not change any functionalities or logic.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-2-git-send-email-quic_cang@quicinc.com
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DMA alignment for the Exynos controller follows directly from the PRDT
segment size configured in ufs-exynos.c. Hence, move the DMA alignment code
into the Exynos driver source code.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230921192335.676924-3-bvanassche@acm.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To
improve here there is a quest to make the remove callback return void. In
the first step of this quest all drivers are converted to .remove_new()
which already returns void. Eventually after all drivers are converted,
.remove_new() is renamed to .remove().
All platform drivers below drivers/ufs/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917145722.1131557-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All UFS host drivers call ufshcd_shutdown(). Hence, instead of calling
ufshcd_shutdown() from the host driver .shutdown() callback, inline that
function into ufshcd_wl_shutdown().
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230524203659.1394307-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not open code SZ_x.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20230531070009.4593-1-avri.altman@wdc.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
