Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Add support for r8a779g0 (R-Car V4H).
This driver previously supported r8a779f0 (R-Car S4-8). PCIe features
of both r8a779f0 and r8a779g0 are almost all the same. For example:
- PCI Express Base Specification Revision 4.0
- Root complex mode and endpoint mode are supported
However, r8a779g0 requires specific firmware to be provided, to
initialize the PHY. Otherwise, the PCIe controller will not work.
[kwilczynski: drop the proprietary firmware conversion comment]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Sequence for controlling the LTSSM state machine is going to change
for SoCs like r8a779f0. Move the LTSSM code to a new callback
ltssm_control() and populate it for each SoCs.
This also warrants the addition of new compatibles for r8a779g0 and
r8a779h0. But since they are already part of the DT binding, it won't
make any difference.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to support future SoCs such as r8a779g0 (R-Car V4H) and
r8a779h0 (R-Car V4M) that require different initialization settings,
introduce SoC specific driver data with the initial member being the
device mode.
No functional change.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
R-Car Gen4 PCIe controller needs to use the Synopsys-specific PCIe
configuration registers. So, add the macros.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
'tegra_pcie_soc' has been unused since 56e15a238d ("PCI: tegra: Add
Tegra194 PCIe support"). Remove it.
Link: https://lore.kernel.org/r/20240527160118.37069-1-linux@treblig.org
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Tegra194 and Tegra234 PCIe EP controllers have 64K alignment restriction
for the inbound ATU. Set the endpoint inbound ATU alignment to 64kB in the
Tegra194 PCIe driver.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Link: https://lore.kernel.org/linux-pci/20240508092207.337063-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to hardcode the clock info in the driver as driver can
rely on the devicetree to supply the clocks required for the functioning
of the peripheral.
Thus, remove the static clock info and obtain the platform supplied
clocks. All the clocks supplied are obtained and enabled using the
devm_clk_bulk_get_all_enable() API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240220084046.23786-3-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the dra7xx_pcie_cpu_addr_fixup() function parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-3-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the artpec6_pcie_cpu_addr_fixup() parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-4-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
SA8775P SoC supports the new Hyper DMA (HDMA) DMA Engine inside the DWC IP,
so add support for it by passing the mapping format and the number of
read/write channels count.
The PCIe EP controller used on this SoC is of version 1.34.0, so a separate
config struct is introduced for the sake of enabling HDMA conditionally.
It should be noted that for the eDMA support (predecessor of HDMA), there
are no mapping format and channels count specified. That is because eDMA
supports auto detection of both parameters, whereas HDMA doesn't.
[mani: reworded commit message, added kdoc, and minor cleanups]
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-4-f04c5cdde760@linaro.org
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Instead of maintaining a separate capability for glue drivers that cannot
support auto detection of the eDMA mapping format, pass the mapping format
directly from them.
This will simplify the code and also allow adding HDMA support that also
doesn't support auto detection of mapping format.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-3-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In the case of Hyper DMA (HDMA) present in DWC controllers, there is no way
the drivers can auto detect the number of read/write channels as like its
predecessor embedded DMA (eDMA). So the glue drivers making use of HDMA
have to pass the channels count during probe.
To accommodate that, skip the existing auto detection of channels count
procedure for HDMA based platforms. If the channels count passed by the
glue drivers were wrong in any form, then the existing sanity check will
catch it.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-2-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In order to add support for Hyper DMA (HDMA), refactor the existing
dw_pcie_edma_find_chip() API by moving the common code to separate
functions.
No functional change.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-1-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add support for SA8775P SoC to the Qualcomm PCIe Endpoint Controller
driver. Adding new compatible string as it has different set of clocks
compared to other SoCs.
Link: https://lore.kernel.org/linux-pci/1714492540-15419-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need for the device drivers to validate the clocks defined in
Devicetree. The validation should be performed by the DT schema and the
drivers should just get all the clocks from DT. Right now the driver
hardcodes the clock info and validates them against DT which is redundant.
So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
and get rid of all static clocks info from the driver. This simplifies the
driver.
Link: https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Return success from endpoint probe before incorrectly dropping the
reference to the BPMP (Vidya Sagar)
* pci/controller/tegra194:
PCI: tegra194: Fix probe path for Endpoint mode
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
"core_init_notifier" flag is set by the glue drivers requiring refclk from
the host to complete the DWC core initialization. Also, those drivers will
send a notification to the EPF drivers once the initialization is fully
completed using the pci_epc_init_notify() API. Only then, the EPF drivers
will start functioning.
For the rest of the drivers generating refclk locally, EPF drivers will
start functioning post binding with them. EPF drivers rely on the
'core_init_notifier' flag to differentiate between the drivers.
Unfortunately, this creates two different flows for the EPF drivers.
So to avoid that, let's get rid of the "core_init_notifier" flag and follow
a single initialization flow for the EPF drivers. This is done by calling
the dw_pcie_ep_init_notify() from all glue drivers after the completion of
dw_pcie_ep_init_registers() API. This will allow all the glue drivers to
send the notification to the EPF drivers once the initialization is fully
completed.
Only difference here is that, the drivers requiring refclk from host will
send the notification once refclk is received, while others will send it
during probe time itself.
But this also requires the EPC core driver to deliver the notification
after EPF driver bind. Because, the glue driver can send the notification
before the EPF drivers bind() and in those cases the EPF drivers will miss
the event. To accommodate this, EPC core is now caching the state of the
EPC initialization in 'init_complete' flag and pci-ep-cfs driver sends the
notification to EPF drivers based on that after each EPF driver bind.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-8-082625472414@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently, dw_pcie_ep_init_registers() API is directly called by the glue
drivers requiring active refclk from host. But for the other drivers, it is
getting called implicitly by dw_pcie_ep_init(). This is due to the fact
that this API initializes DWC EP specific registers and that requires an
active refclk (either from host or generated locally by endpoint itsef).
But, this causes a discrepancy among the glue drivers. So to avoid this
confusion, let's call this API directly from all glue drivers irrespective
of refclk dependency. Only difference here is that the drivers requiring
refclk from host will call this API only after the refclk is received and
other drivers without refclk dependency will call this API right after
dw_pcie_ep_init().
With this change, the check for 'core_init_notifier' flag can now be
dropped from dw_pcie_ep_init() API. This will also allow us to remove the
'core_init_notifier' flag completely in the later commits.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-7-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
The goal of the dw_pcie_ep_init_complete() API is to initialize the DWC
specific registers post registering the controller with the EP framework.
But the naming doesn't reflect its functionality and causes confusion. So,
let's rename it to dw_pcie_ep_init_registers() to make it clear that it
initializes the DWC specific registers.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-6-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
For DWC glue drivers supporting PERST# (currently Qcom and Tegra194), some
of the DWC resources like eDMA should be cleaned up during the PERST#
assert time.
So let's introduce a dw_pcie_ep_cleanup() API that could be called by these
drivers to cleanup the DWC specific resources. Currently, it just removes
eDMA.
Closes: https://lore.kernel.org/linux-pci/ZWYmX8Y%2F7Q9WMxES@x1-carbon
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-5-082625472414@linaro.org
Reported-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
dw_pcie_ep_exit() API is undoing what the dw_pcie_ep_init() API has done
already (at least partly). But the API name dw_pcie_ep_exit() is not quite
reflecting that. So let's rename it to dw_pcie_ep_deinit() to make the
purpose of this API clear. This also aligns with the DWC host driver.
Link: https://patchwork.kernel.org/project/linux-pci/patch/20240327-pci-dbi-rework-v12-4-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
deinit() callback was solely introduced for the pcie-rcar-gen4 driver where
it is used to do platform specific resource deallocation. And this callback
is called right at the end of the dw_pcie_ep_exit() API. So it doesn't
matter whether it is called within or outside of dw_pcie_ep_exit() API.
So let's remove this callback and directly call rcar_gen4_pcie_ep_deinit()
in pcie-rcar-gen4 driver to do resource deallocation after the completion
of dw_pcie_ep_exit() API in rcar_gen4_remove_dw_pcie_ep().
This simplifies the DWC layer.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-3-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
All of the APIs are missing the Kernel-doc comments. Hence, add them.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-2-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
The DWC glue drivers requiring an active reference clock from the PCIe host
for initializing their PCIe EP core, set a flag called 'core_init_notifier'
to let DWC driver know that these drivers need a special attention during
initialization. In these drivers, access to the hw registers (like DBI)
before receiving the active refclk from host will result in access failure
and also could cause a whole system hang.
But the current DWC EP driver doesn't honor the requirements of the drivers
setting 'core_init_notifier' flag and tries to access the DBI registers
during dw_pcie_ep_init(). This causes the system hang for glue drivers such
as Tegra194 and Qcom EP as they depend on refclk from host and have set the
above mentioned flag.
To workaround this issue, users of the affected platforms have to maintain
the dependency with the PCIe host by booting the PCIe EP after host boot.
But this won't provide a good user experience, since PCIe EP is _one_ of
the features of those platforms and it doesn't make sense to delay the
whole platform booting due to PCIe requiring active refclk.
So to fix this issue, let's move all the DBI access from
dw_pcie_ep_init() in the DWC EP driver to the dw_pcie_ep_init_complete()
API. This API will only be called by the drivers setting
'core_init_notifier' flag once refclk is received from host. For the rest
of the drivers that gets the refclk locally, this API will be called
within dw_pcie_ep_init().
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-1-082625472414@linaro.org
Fixes: e966f7390d ("PCI: dwc: Refactor core initialization code for EP mode")
Co-developed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AP3I
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate interrupt related code in irq.c (Ilpo Järvinen)
- Reduce kernel size by replacing sysfs resource macros with
functions (Ilpo Järvinen)
- Reduce kernel size by compiling sysfs support only when
CONFIG_SYSFS=y (Lukas Wunner)
- Avoid using Extended Tags on 3ware-9650SE Root Port to work around
an apparent hardware defect (Jörg Wedekind)
Resource management:
- Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner)
- Move pci_iomap.c and other PCI-specific devres code to drivers/pci
(Philipp Stanner)
- Consolidate PCI devres code in devres.c (Philipp Stanner)
Power management:
- Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't
know how to return correctly to D0, and remove previous quirk that
wasn't as specific (Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any
runtime PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races
between .remove() and .runtime_idle(), which caused intermittent
page faults when the rtsx .runtime_idle() accessed registers that
its .remove() had already unmapped (Rafael J. Wysocki)
Virtualization:
- Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs
with VFIO, e.g., for professional audio software on many Apple
machines, at the cost of leaking state between VMs (Edmund Raile)
Error handling:
- Print all logged TLP Prefixes, not just the first, after AER or DPC
errors (Ilpo Järvinen)
- Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which
still don't advertise a legal size (Paul Menzel)
- Ignore expected DPC Surprise Down errors on hot removal (Smita
Koralahalli)
- Block runtime suspend while handling AER errors to avoid races that
prevent the device form being resumed from D3hot (Stanislaw
Gruszka)
Peer-to-peer DMA:
- Use atomic XA allocation in RCU read section (Christophe JAILLET)
ASPM:
- Collect bits of ASPM-related code that we need even without
CONFIG_PCIEASPM into aspm.c (David E. Box)
- Save/restore L1 PM Substates config for suspend/resume (David E.
Box)
- Update save_save when ASPM config is changed, so a .slot_reset()
during error recovery restores the changed config, not the
.probe()-time config (Vidya Sagar)
Endpoint framework:
- Refactor and improve pci_epf_alloc_space() API (Niklas Cassel)
- Clean up endpoint BAR descriptions (Niklas Cassel)
- Fix ntb_register_device() name leak in error path (Yang Yingliang)
- Return actual error code for pci_vntb_probe() failure (Yang
Yingliang)
Broadcom STB PCIe controller driver:
- Fix MDIO write polling, which previously never waited for
completion (Jonathan Bell)
Cadence PCIe endpoint driver:
- Clear the ARI "Next Function Number" of last function (Jasko-EXT
Wojciech)
Freescale i.MX6 PCIe controller driver:
- Simplify by replacing switch statements with function pointers for
different hardware variants (Frank Li)
- Simplify by using clk_bulk*() API (Frank Li)
- Remove redundant DT clock and reg/reg-name details (Frank Li)
- Add i.MX95 DT and driver support for both Root Complex and Endpoint
mode (Frank Li)
Microsoft Hyper-V host bridge driver:
- Reduce memory usage by limiting ring buffer size to 16KB instead of
4 pages (Michael Kelley)
Qualcomm PCIe controller driver:
- Add X1E80100 DT and driver support (Abel Vesa)
- Add DT 'required-opps' for SoCs that require a minimum performance
level (Johan Hovold)
- Make DT 'msi-map-mask' optional, depending on how MSI interrupts
are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY
configuration isn't tuned correctly for L0s (Johan Hovold)
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and
separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150,
SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof
Kozlowski)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay
Sarkar)
Synopsys DesignWare PCIe controller driver:
- Allocate 64-bit MSI address if no 32-bit address is available (Ajay
Agarwal)
- Fix endpoint Resizable BAR to actually advertise the required 1MB
size (Niklas Cassel)
MicroSemi Switchtec management driver:
- Release resources if the .probe() fails (Christophe JAILLET)
Miscellaneous:
- Make pcie_port_bus_type const (Ricardo B. Marliere)"
* tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits)
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI: hv: Fix ring buffer size calculation
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
PCI: dwc: Strengthen the MSI address allocation logic
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
PCI/AER: Block runtime suspend when handling errors
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
...
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate
files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350,
SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski)
- Allow 'required-opps' DT property for SoCs that require a minimum
performance level for the power domain (Johan Hovold)
- Remove requirement for 'msi-map-mask' DT property since it depends on how
MSIs are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because their PHY
configuration isn't tuned for L0s, which results in many Correctable
Errors (Johan Hovold)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add DT binding and driver support for X1E80100 (Abel Vesa)
* pci/controller/qcom:
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
dt-bindings: PCI: qcom,pcie-sa8775p: Move SA8775p to dedicated schema
dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8180x: Move SC8180X to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8280xp: Move SC8280XP to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8350: Move SM8350 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8150: Move SM8150 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8250: Move SM8250 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8450: Move SM8450 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8550: Move SM8550 to dedicated schema
- Fall back to allocating 64-bit MSI DMA address if unable to allocate a
32-bit address (Ajay Agarwal)
* pci/controller/dwc:
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: dwc: Strengthen the MSI address allocation logic
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
There can be platforms that do not use/have 32-bit DMA addresses.
The current implementation of 32-bit IOVA allocation can fail for
such platforms, eventually leading to the probe failure.
Try to allocate a 32-bit msi_data. If this allocation fails,
attempt a 64-bit address allocation. Please note that if the
64-bit MSI address is allocated, then the EPs supporting 32-bit
MSI address only will not work.
Link: https://lore.kernel.org/linux-pci/20240221153840.1789979-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Will McVicker <willmcvicker@google.com>
Add the compatible and the driver data for X1E80100 PCIe controller.
There are 5 controller instances found on this platform, out of which
2 are Gen3 with speeds of up to 8.0GT/s, while the other 3 are Gen4 with
speeds of up to 16GT/s.
The version of the controller is 1.38.0 for all instances, but they are
compatible with 1.9.0 config. The max link width is x8 for one
controller, x4 for two of others and x2 for the two left.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240301-x1e80100-pci-v4-2-7ab7e281d647@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Commit 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting
1.9.0 ops") started enabling ASPM unconditionally when the hardware
claims to support it. This triggers Correctable Errors for some PCIe
devices on machines like the Lenovo ThinkPad X13s when L0s is enabled,
which could indicate an incomplete driver ASPM implementation or that
the hardware does in fact not support L0s.
This has now been confirmed by Qualcomm to be the case for sc8280xp and
its derivate platforms (e.g. sa8540p and sa8295p). Specifically, the PHY
configuration used on these platforms is not correctly tuned for L0s and
there is currently no updated configuration available.
Add a new flag to the driver configuration data and use it to disable
ASPM L0s on sc8280xp, sa8540p and sa8295p for now.
Note that only the 1.9.0 ops enable ASPM currently.
Link: https://lore.kernel.org/r/20240306095651.4551-4-johan+linaro@kernel.org
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 6.7
Add iMX95 EP support and add 64bit address support.
The internal bus bridge for PCI support 64bit DMA address in iMX95 hence
call dma_set_mask_and_coherent() to set 64 bit DMA mask.
Link: https://lore.kernel.org/r/20240220161924.3871774-15-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The i.MX EP exhibits variations in epc_features among different EP
configurations. This introduces the addition of epc_features in
imx6_pcie_drvdata to accommodate these differences. It's important to note
that there are no functional changes in this commit; instead, it lays the
groundwork for supporting i.MX95 EP functions.
Link: https://lore.kernel.org/r/20240220161924.3871774-13-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the dw_pcie_ep_init() function is already fetching the 'addr_space'
region, no need to do the same in this driver.
Link: https://lore.kernel.org/r/20240220161924.3871774-12-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to initialize the PHY handled by
this driver itself, let's introduce a new callback init_phy() and define it
for platforms that require it.
Link: https://lore.kernel.org/r/20240220161924.3871774-7-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::mode_off and drvdata::mode_mask to simplify
imx6_pcie_configure_type() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-6-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::ltssm_off and drvdata::ltssm_mask to simplify
imx6_pcie_ltssm_enable(disable)() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the reset handling logic in the imx6 PCI driver by adding
IMX6_PCIE_FLAG_HAS_*_RESET bitmask define for drvdata::flags.
The drvdata::flags and bitmask ensure a cleaner and more scalable
switch-case structure for handling reset.
Link: https://lore.kernel.org/r/20240220161924.3871774-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Since some i.MX platforms make use of a separate PHY driver, use
IMX6_PCIE_FLAG_HAS_PHYDRV flag to identify them and get the reference to
PHY from DT to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the clock handling logic. Add 'clk_names' define in drvdata.
Use clk_bulk*() API to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The definition of a reserved BAR is that EPF drivers should not touch
them.
The definition of only_64bit is that the EPF driver must configure this
BAR as 64-bit. (An EPF driver is not allowed to choose if this BAR should
be configured as 32-bit or 64-bit.)
Thus, it does not make sense to put only_64bit of a BAR that EPF drivers
are not allow to touch.
Drop the only_64bit property from hardware descriptions that are of type
reserved BAR.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-3-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The hardware description for BARs is scattered in many different variables
in pci_epc_features. Some of these things are mutually exclusive, so it
can create confusion over which variable that has precedence over another.
Improve the situation by creating a struct pci_epc_bar_desc, and a new
enum pci_epc_bar_type, and convert the endpoint controller drivers to use
this more well defined format.
Additionally, some endpoint controller drivers mark the BAR succeeding a
"64-bit only BAR" as reserved, while some do not. By definition, a 64-bit
BAR uses the succeeding BAR for the upper 32-bits, so an EPF driver cannot
use a BAR succeeding a 64-bit BAR. Ensure that all endpoint controller
drivers are uniform, and actually describe a reserved BAR as reserved.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmXGSRoUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzz/BAAiTzhJJuiDwI9GG5yiyvsNzVuPWqM
L0r3Or3WC7RzibHrVcCzCryjYQCGhrwsFCuknzPRatno4wknqaG2vu3ZinfuBBie
BvIU+gA/fLCD8KZ5ZODOiboR9547ggVpLOxDv/4QKAq8l+YAAJOaoHytySi1HsgG
Pj9Q1D4iYLe6OVZfFTfSMublpAmqnvczFXDRVv1xMT4Kksf0hfX1YwU0l6AEqFTX
DT6kCq6JXH/0ZAZZZq7o9VoxY7BQprATMa8gM0CX6v9PjEg/QmOTpXPRZ5zZyg0b
ppKEDKkLZ69AyXcsjJ55bWbx8yzyzNsPT5nkPg/jCU8gD6DOPAIAGbdnH3jt5LU5
iKYcExt4ciBYgIKkk73FxLGMMvrKWon7kdcgF43atqyzifzxTzWib8h30/wnLuZB
Hnlm/lBcC6ThGQiL0WbW/gmXU6DQx92HDCD4k97JGwpwNL79H2sXCm4xAyvPkNYR
ATYaeG/yswPtfotOjdPIXx9Tq1y07U8btVYyivaDm5q6ty2js6XNaSiCya/W+f5l
+lDz48DbqAEL6hR34dPKFDK6peEuGi4/+CmyHsqYhBt2n7eLL74M7yPme1zwyC9o
qBJiHucog/2cBkOvIdowsNgGua06lFxBlMXKTUN1DNcogLkjKiBJ6zsO757g3tsq
s63ofJw/Tgfv4i8=
=jJks
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Fix an unintentional truncation of DWC MSI-X address to 32 bits and
update similar MSI code to match (Dan Carpenter)
* tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: dwc: Clean up dw_pcie_ep_raise_msi_irq() alignment
PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
I recently changed the alignment code in dw_pcie_ep_raise_msix_irq(). The
code in dw_pcie_ep_raise_msi_irq() is similar, so update it to match, just
for consistency. (No effect on runtime, just a cleanup).
Link: https://lore.kernel.org/r/184097e0-c728-42c7-9e8a-556bd33fb612@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd6 ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
A last minute revert in 6.7-final introduced a potential deadlock when
enabling ASPM during probe of Qualcomm PCIe controllers as reported by
lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0 #40 Not tainted
--------------------------------------------
kworker/u16:5/90 is trying to acquire lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc
but task is already holding lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Call trace:
print_deadlock_bug+0x25c/0x348
__lock_acquire+0x10a4/0x2064
lock_acquire+0x1e8/0x318
down_read+0x60/0x184
pcie_aspm_pm_state_change+0x58/0xdc
pci_set_full_power_state+0xa8/0x114
pci_set_power_state+0xc4/0x120
qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom]
pci_walk_bus+0x64/0xbc
qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom]
The deadlock can easily be reproduced on machines like the Lenovo ThinkPad
X13s by adding a delay to increase the race window during asynchronous
probe where another thread can take a write lock.
Add a new pci_set_power_state_locked() and associated helper functions that
can be called with the PCI bus semaphore held to avoid taking the read lock
twice.
Link: https://lore.kernel.org/r/ZZu0qx2cmn7IwTyQ@hovoldconsulting.com
Link: https://lore.kernel.org/r/20240130100243.11011-1-johan+linaro@kernel.org
Fixes: f93e71aea6 ("Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org> # 6.7
-----BEGIN PGP SIGNATURE-----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=ri0M
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Reserve ECAM so we don't assign it to PCI BARs; this works around
bugs where BIOS included ECAM in a PNP0A03 host bridge window,
didn't reserve it via a PNP0C02 motherboard device, and didn't
allocate space for SR-IOV VF BARs (Bjorn Helgaas)
- Add MMCONFIG/ECAM debug logging (Bjorn Helgaas)
- Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas)
- Log device type (Root Port, Switch Port, etc) during enumeration
(Bjorn Helgaas)
- Log bridges before downstream devices so the dmesg order is more
logical (Bjorn Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc)
consistently instead of a mix of names and "reg 0x10" (Puranjay
Mohan, Bjorn Helgaas)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding
rather than the 8b/10b or 128b/130b used by lower rates (Ilpo
Järvinen)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI
lpfc (Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
Resource management:
- Restructure pci_dev_for_each_resource() to avoid computing the
address of an out-of-bounds array element (the bounds check was
performed later so the element was never actually *read*, but it's
nicer to avoid even computing an out-of-bounds address) (Andy
Shevchenko)
Driver binding:
- Convert pci-host-common.c platform .remove() callback to
.remove_new() returning 'void' since it's not useful to return
error codes here (Uwe Kleine-König)
- Convert exynos, keystone, kirin from .remove() to .remove_new(),
which returns void instead of int (Uwe Kleine-König)
- Drop unused struct pci_driver.node member (Mathias Krause)
Virtualization:
- Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc)
Error handling:
- Log AER errors as "Correctable" (not "Corrected") or
"Uncorrectable" to match spec terminology (Bjorn Helgaas)
- Decode Requester ID when no error info found instead of printing
the raw hex value (Bjorn Helgaas)
Endpoint framework:
- Use a unique test pattern for each BAR in the pci_endpoint_test to
make it easier to debug address translation issues (Niklas Cassel)
Broadcom STB PCIe controller driver:
- Add DT property "brcm,clkreq-mode" and driver support for different
CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan)
Freescale Layerscape PCIe controller driver:
- Add suspend/resume support for Layerscape LS1043a and LS1021a,
including software-managed PME_Turn_Off and transitions between L0,
L2/L3_Ready Link states (Frank Li)
MediaTek PCIe controller driver:
- Clear MSI interrupt status before handler to avoid missing MSIs
that occur after the handler (qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 translation window setup to handle MMIO space
that is not a power of two in size (Jianjun Wang)
Qualcomm PCIe controller driver:
- Increase qcom iommu-map maxItems to accommodate SDX55 (five
entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly
called "reset-names" (Krzysztof Kozlowski)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil
Armstrong)
Renesas R-Car PCIe controller driver:
- Replace of_device.h with explicit of.h include to untangle header
usage (Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v
regulators on KingFisher (Wolfram Sang)
SiFive FU740 PCIe controller driver:
- Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to
ARCH_SIFIVE (Conor Dooley)
Synopsys DesignWare PCIe controller driver:
- Align iATU mapping for endpoint MSI-X (Niklas Cassel)
- Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro
Shimoda)
- Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro
Shimoda)
- Rename struct dw_pcie_ep_ops.func_conf_select() to
.get_dbi_offset() to be more descriptive (Yoshihiro Shimoda)
- Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro
Shimoda)
TI J721E PCIe driver:
- Add j721e DT and driver support for 'num-lanes' for devices that
support x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt
Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is
specific to those TI SoC parts (Peter Robinson)
TI Keystone PCIe controller driver:
- Hold power management references to all PHYs while enabling them to
avoid a race when one provides clocks to others (Siddharth
Vadapalli)
Xilinx XDMA PCIe controller driver:
- Remove redundant dev_err(), since platform_get_irq() and
platform_get_irq_byname() already log errors (Yang Li)
- Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
(Krzysztof Wilczyński)
- Fix xilinx_pl_dma_pcie_init_irq_domain() error return when
irq_domain_add_linear() fails (Harshit Mogalapalli)
MicroSemi Switchtec management driver:
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was
done in stdev_release(), which used stale pointers if stdev->cdev
happened to be open when the PCI device was removed (Daniel
Stodden)
Miscellaneous:
- Convert interrupt terminology from "legacy" to "INTx" to be more
specific and match spec terminology (Damien Le Moal)
- In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of
deprecated ida_simple_*() API with ida_alloc() and ida_free()
(Christophe JAILLET)"
* tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Fix kernel-doc issues
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
PCI: keystone: Fix race condition when initializing PHYs
PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain()
PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error
PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning
PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers
PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops
PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops
PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members
misc: pci_endpoint_test: Use a unique test pattern for each BAR
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI/AER: Use explicit register sizes for struct members
PCI/AER: Decode Requester ID when no error info found
PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors
...
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more explicit and match spec
terminology (Bjorn Helgaas)
- Use existing PCI_IRQ_INTX, PCI_IRQ_MSI, PCI_IRQ_MSIX in artpec6, cadence,
designware, designware-plat, dra7xx, imx6, keembay, keystone, layerscape,
mhi, ntb, qcom, rcar, rcar-gen4, rockchip, tegra194, uniphier, vntb; drop
the redundant pci_epc_irq_type enum with the same values (Damien Le Moal)
- Use "intx" instead of "leg" or "legacy" when describing INTx interrupts
in endpoint core, endpoint tests, cadence, dra7xx, designware,
dw-rockchip, dwc core, imx6, keystone, layerscape, qcom, rcar-gen4,
rockchip, tegra194, uniphier, xilinx-nwl (Damien Le Moal)
* pci/irq-clean-up:
PCI: xilinx-nwl: Use INTX instead of legacy
PCI: rockchip-host: Rename rockchip_pcie_legacy_int_handler()
PCI: rockchip-ep: Use INTX instead of legacy
PCI: uniphier: Use INTX instead of legacy
PCI: tegra194: Use INTX instead of legacy
PCI: dw-rockchip: Rename rockchip_pcie_legacy_int_handler()
PCI: keystone: Use INTX instead of legacy
PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq()
PCI: cadence: Use INTX instead of legacy
PCI: dra7xx: Rename dra7xx_pcie_raise_legacy_irq()
misc: pci_endpoint_test: Use INTX instead of LEGACY
PCI: endpoint: Rename LEGACY to INTX in test function driver
PCI: endpoint: Use INTX instead of legacy
PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitions
PCI: Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX
- Replace of_device.h with explicit of.h include to untangle header usage
(Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators
on KingFisher (Wolfram Sang)
* pci/controller/rcar:
PCI: rcar-host: Add support for optional regulators
dt-bindings: PCI: rcar-pci-host: Add optional regulators
PCI: rcar-gen4: Replace of_device.h with explicit of.h include
- Add suspend/resume support for Layerscape LS1043a, including
software-managed PME_Turn_Off and transitions between L0, L2/L3_Ready
Link states (Frank Li)
* pci/controller/layerscape:
PCI: layerscape: Add suspend/resume for ls1043a
PCI: layerscape(ep): Rename pf_* as pf_lut_*
PCI: layerscape: Add suspend/resume for ls1021a
PCI: layerscape: Add function pointer for exit_from_l2()
- Use devm_kasprintf() to dynamically allocate clock names, removing need
for an intermediate buffer (Christophe JAILLET)
* pci/controller/kirin:
PCI: kirin: Use devm_kasprintf() to dynamically allocate clock names
- Hold power management references to all PHYs while enabling them to avoid
a race when one provides clocks to others (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Fix race condition when initializing PHYs
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
When building with clang 18 with the -Werror compiler option enabled,
the following error will be reported:
drivers/pci/controller/dwc/pcie-rcar-gen4.c:439:15: error: cast to smaller integer type 'enum dw_pcie_device_mode' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
439 | rcar->mode = (enum dw_pcie_device_mode)of_device_get_match_data(&rcar->pdev->dev);
To fix this issue, cast the data the of_device_get_match_data() helper
returns to uintptr_t rather than the dw_pcie_device_mode enum.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The current code calculated some dbi[2] registers' offset by calling
dw_pcie_ep_get_dbi[2]_offset() in each function. To improve the code
readability, add dw_pcie_ep_{read,write}_dbi[2} and some data-width
related helpers.
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the struct member .func_conf_select makes the intentions behind it
difficult to ascertain from its name alone, rename it to .get_dbi_offset
to make the intended usage more obvious.
[kwilczynski: commmit log]
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since the name of the dw_pcie_ep_ops struct makes it obvious that it's
for the PCIe Endpoint, rename the struct member .ep_init to .init.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Since the name of the dw_pcie_host_ops struct makes it obvious that it's
for the PCIe Host, drop the host prefix from the struct members.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Lei Chuanhua <lchuanhua@maxlinear.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
In the Designware uniphier controller driver, including the endpoint
driver, change all names using "legacy" to use "intx", to match the
term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Designware tegra194 controller driver, change all names using
"legacy" to use "intx", to match the term used in the PCI
specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function rockchip_pcie_legacy_int_handler() to
rockchip_pcie_intx_handler() to match the code managing INTX interrupts
(e.g. intx_domain_ops) and the term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Keystone controller driver, change all names using "legacy" to
use "intx" instead, to match the term used in the PCI specifications.
Given that the field legacy_intc_np of struct keystone_pcie is unused,
this field is removed instead of being renamed.
Link: https://lore.kernel.org/r/20231122060406.14695-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dw_pcie_ep_raise_legacy_irq() of the Designware
endpoint controller driver to dw_pcie_ep_raise_intx_irq() to match the
name of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dra7xx_pcie_raise_legacy_irq() to
dra7xx_pcie_raise_intx_irq() to match the use of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
linux/pci.h defines the IRQ flags PCI_IRQ_INTX, PCI_IRQ_MSI and
PCI_IRQ_MSIX. Let's use these flags directly instead of the endpoint
definitions provided by enum pci_epc_irq_type. This removes the need
for defining this enum type completely.
Link: https://lore.kernel.org/r/20231122060406.14695-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Use devm_kasprintf() instead of open coding it. This saves the need of
an intermediate buffer.
There was also no reason to use devm_kstrdup_const() as string is known
to be constant.
[kwilczynski: commit log, and add missing Reviewed-by tag]
Link: https://lore.kernel.org/linux-pci/1bad6879083a7d836c8a47418a0afa22485e8f69.1700294127.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/c3a51791d54deaa818b8526975fc4e16ef1090ce.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/06612aff79dfb52d5b0b20129dff5e4b1f04d3a7.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/50de44ea8931465fd9cdc821854ea761cb43adf6.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive PCI
drivers to use the newer symbol.
Link: https://lore.kernel.org/linux-pci/20230918-safeness-cornflake-62278bc3aaaa@wendy
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform
bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
As a result, there's a pretty much random mix of those include files
used throughout the tree. In order to detangle these headers and replace
the implicit includes with struct declarations, users need to explicitly
include the correct includes.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231207165251.2855783-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add suspend/resume support for Layerscape LS1043a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
'pf' and 'lut' are two different acronyms describing the same
thing, basically it is a MMIO base address plus an offset.
Rename them to avoid duplicate pf_* and lut_* naming schemes in the
driver.
Link: https://lore.kernel.org/r/20231204160829.2498703-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Add suspend/resume support for Layerscape LS1021a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Since different SoCs require different sequences for exiting L2, let's add
a separate "exit_from_l2()" callback to handle SoC specific sequences.
Change ls_pcie_exit_from_l2() return value from void to int in order
to propagate errors. Return an error if the exit_from_l2() callback
fails in the resume flow.
Link: https://lore.kernel.org/r/20231204160829.2498703-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Break up the newly added ASPM comment so that it fits within the soft 80
character limit and becomes more readable.
Link: https://lore.kernel.org/r/20231128081512.19387-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom_pcie_enable_aspm() helper is called from pci_walk_bus() during
host init to enable ASPM.
Since pci_walk_bus() already holds a pci_bus_sem read lock, use
pci_enable_link_state_locked() to enable link states in order to avoid a
potential deadlock (e.g. in case someone takes a write lock before
reacquiring the read lock).
This issue was reported by lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0-rc1 #4 Not tainted
--------------------------------------------
kworker/u16:6/147 is trying to acquire lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_enable_link_state+0x74/0x1e8
but task is already holding lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Link: https://lore.kernel.org/r/20231128081512.19387-4-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
[bhelgaas: add "potential" in subject since the deadlock has only been
reported by lockdep, include helper name in commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
- Use FIELD_GET()/FIELD_PREP() when possible throughout drivers/pci/ (Ilpo
Järvinen, Bjorn Helgaas)
- Rework DPC control programming for clarity (Ilpo Järvinen)
* pci/field-get:
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
PCI: Use FIELD_GET()
PCI/MSI: Use FIELD_GET/PREP()
PCI/DPC: Use defines with DPC reason fields
PCI/DPC: Use defined fields with DPC_CTL register
PCI/DPC: Use FIELD_GET()
PCI: hotplug: Use FIELD_GET/PREP()
PCI: dwc: Use FIELD_GET/PREP()
PCI: cadence: Use FIELD_GET()
PCI: Use FIELD_GET() to extract Link Width
PCI: mvebu: Use FIELD_PREP() with Link Width
PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
# Conflicts:
# drivers/pci/controller/dwc/pcie-tegra194.c
- Use PCIE_SPEED2MBS_ENC() macro in qcom host and endpoint to encode link
speed instead of hard-coding the link speed in MBps (Manivannan
Sadhasivam)
- Use Mbps_to_icc() (not MBps_to_icc()) in tegra194 instead of explicitly
doing the bytes-to-bits conversion (Manivannan Sadhasivam)
* pci/controller/speed:
PCI: tegra194: Use Mbps_to_icc() macro for setting icc speed
PCI: qcom-ep: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
PCI: qcom: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
- Add generic T_PVPERL macro for the required interval between power being
stable and PERST# being inactive (Yoshihiro Shimoda)
- Factor out dw_pcie_link_set_max_link_width() (Yoshihiro Shimoda)
- Update PCI_EXP_LNKCAP_MLW so Link Capabilities shows the correct max link
width (Yoshihiro Shimoda)
- Drop tegra194 PCI_EXP_LNKCAP_MLW setting since dw_pcie_setup() already
does it (Yoshihiro Shimoda)
- Add dwc support for different dbi and dbi2 register offsets, to be used
for R-Car Gen4 controllers (Yoshihiro Shimoda)
- Add EDMA_UNROLL capability flag for R-Car Gen4 controllers that don't
correctly advertise unrolled mapping via their eDMA CTRL register
(Yoshihiro Shimoda)
- Export dw_pcie_ep_exit() for use by the modular R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add .pre_init() and .deinit() hooks for use by R-Car Gen4 controllers
(Yoshihiro Shimoda)
- Increase snps,dw-pcie DT reg and reg-names maxItems for R-Car Gen4
controllers (Yoshihiro Shimoda)
- Add rcar-gen4-pci host and endpoint DT bindings and drivers (Yoshihiro
Shimoda)
- Add Renesas R8A779F0 Device ID to pci_endpoint_test to allow testing on
R-Car S4-8 (Yoshihiro Shimoda)
* pci/controller/rcar:
misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller
MAINTAINERS: Update PCI DRIVER FOR RENESAS R-CAR for R-Car Gen4
PCI: rcar-gen4: Add endpoint mode support
PCI: rcar-gen4: Add R-Car Gen4 PCIe controller support for host mode
dt-bindings: PCI: renesas: Add R-Car Gen4 PCIe Endpoint
dt-bindings: PCI: renesas: Add R-Car Gen4 PCIe Host
dt-bindings: PCI: dwc: Update maxItems of reg and reg-names
PCI: dwc: endpoint: Introduce .pre_init() and .deinit()
PCI: dwc: Expose dw_pcie_write_dbi2() to module
PCI: dwc: Expose dw_pcie_ep_exit() to module
PCI: dwc: Add EDMA_UNROLL capability flag
PCI: dwc: endpoint: Add multiple PFs support for dbi2
PCI: tegra194: Drop PCI_EXP_LNKSTA_NLW setting
PCI: dwc: Add missing PCI_EXP_LNKCAP_MLW handling
PCI: dwc: Add dw_pcie_link_set_max_link_width()
PCI: Add T_PVPERL macro
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Convert open-coded variants of PCI field access into FIELD_GET/PREP()
to make the code easier to understand.
Add two missing defines into pci_regs.h. Logically, the Max No-Snoop
Latency Register is a separate word sized register in the PCIe spec,
but the pre-existing LTR defines in pci_regs.h with dword long values
seem to consider the registers together (the same goes for the only
user). Thus, follow the custom and make the new values also take both
word long LTR registers as a joint dword register.
Link: https://lore.kernel.org/r/20231024110336.26264-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code like mode setting and retraining and
so on.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-13-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Renesas R-Car Gen4 PCIe controllers require vendor-specific
initialization before .init().
To use dw->dbi and dw->num-lanes in the initialization code,
introduce .pre_init() into struct dw_pcie_ep_ops. While at it,
also introduce .deinit() to disable the controller by using
vendor-specific de-initialization.
Note that the ep_init in the struct dw_pcie_ep_ops should be
renamed to init later.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-9-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since no PCIe controller drivers call this, this change is not required
for now. But, Renesas R-Car Gen4 PCIe controller driver will call this
and if the controller driver is built as a kernel module, the following
build error happens:
ERROR: modpost: "dw_pcie_write_dbi2" [drivers/pci/controller/dwc/pcie-rcar-gen4-host-drv.ko] undefined!
So, expose dw_pcie_write_dbi2() for it.
Link: https://lore.kernel.org/linux-pci/20230926122431.3974714-8-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since no PCIe controller drivers call this, this change is not required
for now. But, Renesas R-Car Gen4 PCIe controller driver will call this
and if the controller driver is built as a kernel module, the following
build error happens:
ERROR: modpost: "dw_pcie_ep_exit" [drivers/pci/controller/dwc/pcie-rcar-gen4-ep-drv.ko] undefined!
So, expose dw_pcie_ep_exit() for it.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-8-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Renesas R-Car Gen4 PCIe controllers have an unexpected register value in
the eDMA CTRL register.
So, add a new capability flag "EDMA_UNROLL" which would force the unrolled
eDMA mapping for the problematic device.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
The commit 24ede430fa ("PCI: designware-ep: Add multiple PFs support
for DWC") added .func_conf_select() to get the configuration space of
different PFs and assumed that the offsets between dbi and dbi2 would
be the same.
However, Renesas R-Car Gen4 PCIe controllers have different offsets of
function 1: dbi (+0x1000) and dbi2 (+0x800). To get the offset for dbi2,
add .get_dbi2_offset() and dw_pcie_ep_get_dbi2_offset().
Note:
- .func_conf_select() should be renamed later.
- dw_pcie_ep_get_dbi2_offset() will call .func_conf_select()
if .get_dbi2_offset() doesn't exist for backward compatibility.
- dw_pcie_writeX_{dbi/dbi2} APIs accepted the func_no argument,
so that these offset calculations are contained in the API
definitions itself as it should.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-6-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
dw_pcie_setup() is already setting PCI_EXP_LNKCAP_MLW to pcie->num_lanes
in the PCI_EXP_LNKCAP register for programming maximum link width.
Hence, remove the redundant setting here.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Update dw_pcie_link_set_max_link_width() to set PCI_EXP_LNKCAP_MLW.
In accordance with the DW PCIe RC/EP HW manuals [1,2,3,...] aside with
the PORT_LINK_CTRL_OFF.LINK_CAPABLE and GEN2_CTRL_OFF.NUM_OF_LANES[8:0]
field there is another one which needs to be updated.
It's LINK_CAPABILITIES_REG.PCIE_CAP_MAX_LINK_WIDTH. If it isn't done at
the very least the maximum link-width capability CSR won't expose the
actual maximum capability.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.60a, March 2015, p.1032
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.70a, March 2016, p.1065
[3] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.90a, March 2016, p.1057
...
[X] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
Version 5.40a, March 2019, p.1396
[X+1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 5.40a, March 2019, p.1266
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Max-Link-width capability
setup which would in its turn complete the max-link-width setup
procedure defined by Synopsys in the HW-manual.
Seeing there is a max-link-speed setup method defined in the DW PCIe
core driver it would be good to have a similar function for the link
width setup.
That's why we need to define a dedicated function first from already
implemented but incomplete link-width setting up code.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
ASPM is supported by Qcom host controllers/bridges on most of the recent
platforms and so the devices tested so far. But for enabling ASPM by
default (without using Kconfig, kernel command-line or sysfs), BIOS has
to enable ASPM on both host bridge and downstream devices during boot.
Unfortunately, none of the BIOS available on Qcom platforms enables
ASPM. Due to this, the platforms making use of Qcom SoCs draw high power
during runtime.
To fix this power draw issue, users have to enable ASPM using Kconfig,
kernel command-line, sysfs or the BIOS has to start enabling ASPM.
The latter may happen in the future, but that won't address the issue on
current platforms. Also, asking users to enable a feature to get the power
management right would provide an unpleasant out-of-the-box experience.
So the apt solution is to enable ASPM in the controller driver itself. And
this is being accomplished by calling pci_enable_link_state() in the newly
introduced host_post_init() callback for all the devices connected to the
bus. This function enables all supported link low power states for both
host bridge and the downstream devices.
Due to limited testing, ASPM is only enabled for platforms making use of
ops_1_9_0 callbacks.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231010155914.9516-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
This callback can be used by the platform drivers to do configuration
once all the devices are scanned. Like changing LNKCTL of all downstream
devices to enable ASPM etc...
Link: https://lore.kernel.org/linux-pci/20231010155914.9516-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PCIe speed returned by the PCIE_SPEED2MBS_ENC() macro is in Mbps. So
instead of converting it to MBps explicitly and using the MBps_to_icc()
macro, let's use the Mbps_to_icc() macro to pass the value directly.
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Vidya Sagar <vidyas@nvidia.com>
Instead of hardcoding the link speed in MBps, use existing
PCIE_SPEED2MBS_ENC() macro that does the encoding of the link speed for
us. Also, let's Wrap it with QCOM_PCIE_LINK_SPEED_TO_BW() macro to do
the conversion to ICC speed.
This eliminates the need for a switch case in qcom_pcie_icc_update() and
also works for future Gen speeds without any code modifications.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Instead of hardcoding the link speed in MBps, use existing
PCIE_SPEED2MBS_ENC() macro that does the encoding of the link speed for
us. Also, let's Wrap it with QCOM_PCIE_LINK_SPEED_TO_BW() macro to do
the conversion to ICC speed.
This eliminates the need for a switch case in qcom_pcie_icc_update() and
also works for future Gen speeds without any code modifications.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20231004164430.39662-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).
Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The __init annotation makes the ks_pcie_probe() function disappear after
booting completes. However a device can also be bound later. In that case,
we try to call ks_pcie_probe(), but the backing memory is likely already
overwritten.
The right thing to do is do always have the probe callback available. Note
that the (wrong) __refdata annotation prevented this issue to be noticed by
modpost.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
Note that this driver cannot be compiled as a module, so ks_pcie_remove()
was always discarded before this change and modpost couldn't warn about
this issue. Furthermore the __ref annotation also prevents a warning.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 000f60db78 ("PCI: kirin: Add support for a PHY layer")
Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 340cba6092 ("pci: Add PCIe driver for Samsung Exynos")
Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: stable@vger.kernel.org
Replace literals under drivers/pci/ with PCI_HEADER_TYPE_MASK,
PCI_HEADER_TYPE_NORMAL, and PCI_HEADER_TYPE_MFD.
Also replace !! boolean conversions with FIELD_GET().
Link: https://lore.kernel.org/r/20231003125300.5541-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for Renesas R-Car
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f6 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
Fixes: 39171b33f6 ("PCI: qcom: Remove PCIE20_ prefix from register definitions")
Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org # v6.4+
-----BEGIN PGP SIGNATURE-----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=iFFM
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Add locking to read/modify/write PCIe Capability Register accessors
for Link Control and Root Control
- Use pci_dev_id() when possible instead of manually composing ID
from dev->bus->number and dev->devfn
Resource management:
- Move prototypes for __weak sysfs resource files to linux/pci.h to
fix 'no previous prototype' warnings
- Make more I/O port accesses depend on HAS_IOPORT
- Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource()
Power management:
- Ensure devices are powered up while accessing VPD
- If device is powered-up, keep it that way while polling for PME
- Only read PCI_PM_CTRL register when available, to avoid reading the
wrong register and corrupting dev->current_state
Virtualization:
- Avoid Secondary Bus Reset on NVIDIA T4 GPUs
Error handling:
- Remove unused pci_disable_pcie_error_reporting()
- Unexport pci_enable_pcie_error_reporting(), used only by aer.c
- Unexport pcie_port_bus_type, used only by PCI core
VGA:
- Simplify and clean up typos in VGA arbiter
Apple PCIe controller driver:
- Initialize pcie->nvecs (number of available MSIs) before use
Broadcom iProc PCIe controller driver:
- Use of_property_read_bool() instead of low-level accessors for
boolean properties
Broadcom STB PCIe controller driver:
- Assert PERST# when probing BCM2711 because some bootloaders don't
do it
Freescale i.MX6 PCIe controller driver:
- Add .host_deinit() callback so we can clean up things like
regulators on probe failure or driver unload
Freescale Layerscape PCIe controller driver:
- Add support for link-down notification so the endpoint driver can
process LINK_DOWN events
- Add suspend/resume support, including manual
PME_Turn_off/PME_TO_Ack handshake
- Save Link Capabilities during probe so they can be restored when
handling a link-up event, since the controller loses the Link Width
and Link Speed values during reset
Intel VMD host bridge driver:
- Fix disable of bridge windows during domain reset; previously we
cleared the base/limit registers, which actually left the windows
enabled
Marvell MVEBU PCIe controller driver:
- Remove unused busn member
Microchip PolarFlare PCIe controller driver:
- Fix interrupt bit definitions so the SEC and DED interrupt handlers
work correctly
- Make driver buildable as a module
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them
Microsoft Hyper-V host bridge driver:
- To avoid a NULL pointer dereference, skip MSI restore after
hibernate if MSI/MSI-X hasn't been enabled
NVIDIA Tegra194 PCIe controller driver:
- Revert 'PCI: tegra194: Enable support for 256 Byte payload' because
Linux doesn't know how to reduce MPS from to 256 to 128 bytes for
endpoints below a switch (because other devices below the switch
might already be operating), which leads to 'Malformed TLP' errors
Qualcomm PCIe controller driver:
- Add DT and driver support for interconnect bandwidth voting for
'pcie-mem' and 'cpu-pcie' interconnects
- Fix broken SDX65 'compatible' DT property
- Configure controller so MHI bus master clock will be switched off
while in ASPM L1.x states
- Use alignment restriction from EPF core in EPF MHI driver
- Add Endpoint eDMA support
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driver
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency
- Add sa8775p DT binding and driver support
Rockchip PCIe controller driver:
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the
upper 32 bits
SiFive FU740 PCIe controller driver:
- Set the supported number of MSI vectors so we can use all available
MSI interrupts
Synopsys DesignWare PCIe controller driver:
- Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq()) to be called by controller driver
suspend/resume ops, and a controller callback to send PME_Turn_Off
MicroSemi Switchtec management driver:
- Add support for PCIe Gen5 devices
Miscellaneous:
- Reorder and compress to reduce size of struct pci_dev
- Fix race in DOE destroy_work_on_stack()
- Add stubs to avoid casts between incompatible function types
- Explicitly include correct DT includes to untangle headers"
* tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits)
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI/PM: Only read PCI_PM_CTRL register when available
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Pass alignment restriction to the EPF core
PCI: Simplify pcie_capability_clear_and_set_word() control flow
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
...
- Reorder struct pci_dev to avoid holes and reduce size (Christophe
JAILLET)
- Change pdev->rom_attr_enabled to single bit since it's only a boolean
value (Christophe JAILLET)
- Use struct_size() in pirq_convert_irt_table() instead of hand-writing it
(Christophe JAILLET)
- Explicitly include correct DT includes to untangle headers (Rob Herring)
- Fix a DOE race between destroy_work_on_stack() and the stack-allocated
task->work struct going out of scope in pci_doe() (Ira Weiny)
- Use pci_dev_id() when possible instead of manually composing ID from
dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai)
- Move pci_create_resource_files() declarations to linux/pci.h for alpha
build warnings (Arnd Bergmann)
- Remove unused hotplug function declarations (Yue Haibing)
- Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár)
- Unexport pcie_port_bus_type (Bjorn Helgaas)
- Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas)
- Fix BAR value printk formatting to accommodate 32-bit values (Bjorn
Helgaas)
- Use consistent pointer types for config access syscall get_user() and
put_user() uses (Bjorn Helgaas)
- Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas)
- Simplify pci_pio_to_address() (Bjorn Helgaas)
- Simplify pci_dev_driver() (Bjorn Helgaas)
- Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas)
- Fix code and doc typos and code formatting (Bjorn Helgaas)
- Tidy config space save/restore messages (Bjorn Helgaas)
* pci/misc:
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
PCI: Simplify pci_pio_to_address()
PCI/AER: Simplify AER_RECOVER_RING_SIZE definition
PCI: Use consistent put_user() pointer types
PCI: Fix printk field formatting
PCI: Remove unnecessary initializations
PCI: Unexport pcie_port_bus_type
PCI: mvebu: Remove unused busn member
PCI: Remove unused function declarations
PCI/sysfs: Move declarations to linux/pci.h
PCI/P2PDMA: Use pci_dev_id() to simplify the code
PCI/IOV: Use pci_dev_id() to simplify the code
PCI/AER: Use pci_dev_id() to simplify the code
PCI: apple: Use pci_dev_id() to simplify the code
PCI/DOE: Fix destroy_work_on_stack() race
PCI: Explicitly include correct DT includes
x86/PCI: Use struct_size() in pirq_convert_irt_table()
PCI: Change pdev->rom_attr_enabled to single bit
PCI: Reorder pci_dev fields to reduce holes
- Use Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource() (Yang Li)
* pci/controller/resources:
PCI: imx6: Use devm_platform_get_and_ioremap_resource()
PCI: xgene-msi: Use devm_platform_get_and_ioremap_resource()
PCI: v3: Use devm_platform_get_and_ioremap_resource()
PCI: rcar-gen2: Use devm_platform_get_and_ioremap_resource()
- Add stubs for devm action functions that call clk_disable_unprepare() to
avoid casts between incompatible function types (Krzysztof Wilczyński)
* pci/controller/remove-void-cast:
PCI: microchip: Remove cast between incompatible function type
PCI: keembay: Remove cast between incompatible function type
PCI: meson: Remove cast between incompatible function type
- Revert "PCI: tegra194: Enable support for 256 Byte payload" because Linux
doesn't know how to reduce MPS from to 256 to 128 bytes for Endpoints
below a Switch (because other devices below the Switch might already be
operating), which leads to Malformed TLP errors (Vidya Sagar)
* pci/controller/tegra194:
Revert "PCI: tegra194: Enable support for 256 Byte payload"
- Pass the Qcom Endpoint 4K alignment requirement for outbound windows to
the EPF core so EPF drivers can use it (Manivannan Sadhasivam)
- Use alignment restriction from EPF core in Qcom EPF MHI driver
(Manivannan Sadhasivam)
- Add Qcom Endpoint eDMA support by enabling the eDMA IRQ (Manivannan
Sadhasivam)
- Add Qcom MHI eDMA support (Manivannan Sadhasivam)
- Add Qcom Snapdragon SM8450 support to the EPF MHI driver (Manivannan
Sadhasivam)
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency (Manivannan Sadhasivam)
- Add pci_epc_mem_init() kernel-doc (Manivannan Sadhasivam)
* pci/controller/qcom-edma:
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI: qcom-ep: Pass alignment restriction to the EPF core
- Configure controller so MHI bus master clock will be switched off while
in ASPM L1.x states (Manivannan Sadhasivam)
- Add sa8775p DT binding and driver support (Mrinmay Sarkar)
- Fix broken DT SDX65 "compatible" property (Krzysztof Kozlowski)
* pci/controller/qcom:
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Switch MHI bus master clock off during L1SS
- Add support for link-down notification so the endpoint driver can process
LINK_DOWN events (Frank Li)
- Save Link Capabilities during probe so they can be restored when handling
a link-up event, since the controller loses the Link Width and Link Speed
values during reset (Xiaowei Bao)
* pci/controller/layerscape:
PCI: layerscape: Add workaround for lost link capabilities during reset
PCI: layerscape: Add support for link-down notification
- Set the supported number of MSI vectors so we can use all available MSI
interrupts (Yong-Xuan Wang)
* pci/controller/fu740:
PCI: fu740: Set the number of MSI vectors
Add support for voting interconnect (ICC) bandwidth based
on the link speed and width.
This commit is inspired from the basic interconnect support added
to pcie-qcom driver in commit c4860af88d ("PCI: qcom: Add basic
interconnect support").
The interconnect support is kept optional to be backward compatible
with legacy device trees.
[kwilczynski: add missing kernel-doc for the icc_mem variable]
Link: https://lore.kernel.org/linux-pci/1689751218-24492-5-git-send-email-quic_krichai@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Sometimes, the Qcom PCIe EP controller can receive some interrupts
unknown to the driver, like safety interrupts in newer SoCs. In those
cases, if the driver doesn't clear the interrupts, it will end up in an
interrupt storm. However, the users will not know about it because the
log is treated as a debug message.
So let's treat the unknown event log as an error so that it at least
makes the user aware, thereby getting fixed eventually.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230726152931.18134-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qualcomm PCIe Endpoint controllers have the in-built Embedded DMA (eDMA)
peripheral for offloading the data transfer between the PCIe bus and
memory.
Let's add support for it by enabling the eDMA IRQ in the driver. The
eDMA DMA Engine driver will handle the rest of the functionality.
Since the eDMA on Qualcomm platforms only uses a single IRQ for all
channels, use 1 for edma.nr_irqs.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230717065459.14138-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qcom PCIe EP controllers have 4K alignment restriction for the outbound
window address. Hence, pass this info to the EPF core so that the EPF
drivers can make use of this info.
Link: https://lore.kernel.org/linux-pci/20230717065459.14138-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add PME_Turn_off/PME_TO_Ack handshake sequence for ls1028a platform.
Implemented on top of common dwc dw_pcie_suspend(resume)_noirq()
functions to handle system enter/exit suspend states.
Link: https://lore.kernel.org/r/20230821184815.2167131-4-Frank.Li@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Introduce an helper function (dw_pcie_get_ltssm()) to retrieve
SMLH_LTSS_STATE.
Add common dw_pcie_suspend(resume)_noirq() API to implement the DWC
controller generic suspend/resume functionality.
Add a controller specific callback to send the PME_Turn_Off message
(ie .pme_turn_off) for controller platform specific PME handling.
Link: https://lore.kernel.org/r/20230821184815.2167131-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[lpieralisi@kernel.org: commit log]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
The endpoint controller loses the Maximum Link Width and Supported Link Speed
value from the Link Capabilities Register - initially configured by the Reset
Configuration Word (RCW) - during a link-down or hot reset event.
Address this issue in the endpoint event handler.
Link: https://lore.kernel.org/r/20230720135834.1977616-2-Frank.Li@nxp.com
Fixes: a805770d8a ("PCI: layerscape: Add EP mode support")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Add support to pass link-down notification to the endpoint function
driver so that it can process the LINK_DOWN event.
Link: https://lore.kernel.org/r/20230720135834.1977616-1-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
The iMSI-RX module of the DW PCIe controller provides multiple sets of
MSI_CTRL_INT_i_* registers, and each set is capable of handling 32 MSI
interrupts. However, the fu740 PCIe controller driver only enabled one set
of MSI_CTRL_INT_i_* registers, as the total number of supported interrupts
was not specified.
Set the supported number of MSI vectors to enable all the MSI_CTRL_INT_i_*
registers on the fu740 PCIe core, allowing the system to fully utilize the
available MSI interrupts.
Link: https://lore.kernel.org/r/20230807055621.2431-1-yongxuan.wang@sifive.com
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
The i.MX integration for the DesignWare PCI controller has a _host_exit()
operation which undoes everything that the _host_init() operation does but
does not wire this up as the host_deinit callback for the core, or call it
in any path other than suspend. This means that if we ever unwind the
initial probe of the device, for example because it fails, the regulator
core complains that the regulators for the device were left enabled:
imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie: probe of 33800000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 2 PID: 46 at drivers/regulator/core.c:2396 _regulator_put+0x110/0x128
Wire up the callback so that the core can clean up after itself.
Link: https://lore.kernel.org/r/20230731-pci-imx-regulator-cleanup-v2-1-fc8fa5c9893d@kernel.org
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload"), we initialize MPS=256 for tegra194 Root Ports before enumerating
the hierarchy.
Consider an Endpoint that supports only MPS=128. In the default situation
(CONFIG_PCIE_BUS_DEFAULT set and no "pci=pcie_bus_*" parameter), Linux
tries to configure the MPS of every device to match the upstream bridge.
If the Endpoint is directly below the Root Port, Linux can reduce the Root
Port MPS to 128 to match the Endpoint. But if there's a switch in the
middle, Linux doesn't reduce the Root Port MPS because other devices below
the switch may already be configured with MPS larger than 128.
This scenario results in uncorrectable Malformed TLP errors if the Root
Port sends TLPs with payloads larger than 128 bytes. These errors can
be avoided by using the "pci=pcie_bus_safe" parameter, but it doesn't
seem to be a good idea to always have this parameter even for basic
functionality to work.
Revert commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload") so the Root Ports default to MPS=128, which all devices
support.
If peer-to-peer DMA is not required, one can use "pci=pcie_bus_perf" to
get the benefit of larger MPS settings.
[bhelgaas: commit log; kwilczynski: retain "u16 val_16" declaration at
the top, add missing acked by tag]
Fixes: 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte payload")
Link: https://lore.kernel.org/linux-pci/20230619102604.3735001-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org # v6.0-rc1+
This reverts commit da56a1bfba.
Bjorn Andersson, Fabio Estevam, Xiaolei Wang, and Jon Hunter reported that
da56a1bfba ("PCI: dwc: Wait for link up only if link is started") broke
controller probing by returning an error in case the link does not come up
during host initialisation, for example when the slot is empty.
As explained in commit 886a9c1347 ("PCI: dwc: Move link handling into
common code") and as indicated by the comment "Ignore errors, the link may
come up later" in the code, waiting for link up and ignoring errors is the
intended behaviour:
Let's standardize this to succeed as there are usecases where devices
(and the link) appear later even without hotplug. For example, a
reconfigured FPGA device.
Reverting the offending commit specifically fixes a regression on Qualcomm
platforms like the Lenovo ThinkPad X13s which no longer reach the
interconnect sync state if a slot does not have a device populated (e.g. an
optional modem).
Note that enabling asynchronous probing by default as was done for Qualcomm
platforms by commit c0e1eb441b ("PCI: qcom: Enable async probe by
default"), should take care of any related boot time concerns.
Finally, note that the intel-gw driver is the only driver currently not
providing a .start_link() callback and instead starts the link in its
.host_init() callback, which may avoid an additional one-second timeout
during probe by making the link-up wait conditional. If anyone cares, that
can be done in a follow-up patch with a proper motivation.
[bhelgaas: add Fabio Estevam, Xiaolei Wang, Jon Hunter reports]
Fixes: da56a1bfba ("PCI: dwc: Wait for link up only if link is started")
Link: https://lore.kernel.org/r/20230706082610.26584-1-johan+linaro@kernel.org
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20230704122635.1362156-1-festevam@gmail.com/
Reported-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20230705010624.3912934-1-xiaolei.wang@windriver.com/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/6ca287a1-6c7c-7b90-9022-9e73fb82b564@nvidia.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Sajid Dalvi <sdalvi@google.com>
Cc: Ajay Agarwal <ajayagarwal@google.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rather than casting void(*)(struct clk *) to void (*)(void *), that
forces conversion to an incompatible function type, replace the cast
with a small local stub function with a signature that matches what
the devm_add_action_or_reset() function expects.
The sub function takes a void *, then passes it directly to
clk_disable_unprepare(), which handles the more specific type.
Reported by clang when building with warnings enabled:
drivers/pci/controller/dwc/pcie-keembay.c:172:12: warning: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict]
(void(*)(void *))clk_disable_unprepare,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
No functional changes are intended.
Fixes: 0c87f90b4c ("PCI: keembay: Add support for Intel Keem Bay")
Link: https://lore.kernel.org/linux-pci/20230629165956.237832-2-kwilczynski@kernel.org
Acked-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Rather than casting void(*)(struct clk *) to void (*)(void *), that
forces conversion to an incompatible function type, replace the cast
with a small local stub function with a signature that matches what
the devm_add_action_or_reset() function expects.
The sub function takes a void *, then passes it directly to
clk_disable_unprepare(), which handles the more specific type.
Reported by clang when building with warnings enabled:
drivers/pci/controller/dwc/pci-meson.c:191:6: warning: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict]
(void (*) (void *))clk_disable_unprepare,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
No functional changes are intended.
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Link: https://lore.kernel.org/linux-pci/20230629165956.237832-1-kwilczynski@kernel.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Convert calls to platform_get_resource() and devm_ioremap_resource()
into a single call to devm_platform_get_and_ioremap_resource(), to
simplify the code.
This new helper added in commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()") does what both of the
other separate functions do.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230323074553.90372-1-yang.lee@linux.alibaba.com
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Currently, as part of the qcom_pcie_perst_deassert() function, instead
of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable
"val" is re-read.
This must be fixed to ensure that the master clock supplied to the MHI
bus is correctly gated during L1.1/L1.2 to save power.
Thus, replace the line that re-reads "val" with a line that writes the
updated value to the register to clear PARF_MSTR_AXI_CLK_EN.
[kwilczynski: commit log]
Fixes: c457ac029e ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS")
Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org
Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
New support:
- TI J721S2 CSI BCDMA support
Updates:
- Native HDMI support for dw edma driver
- ste dma40 updates for supporting proper SRAM handle in DT
- removal of dma device chancnt setting in drivers
-----BEGIN PGP SIGNATURE-----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=pGmA
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- TI J721S2 CSI BCDMA support
Updates:
- Native HDMI support for dw edma driver
- ste dma40 updates for supporting proper SRAM handle in DT
- removal of dma device chancnt setting in drivers"
* tag 'dmaengine-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (28 commits)
dmaengine: sprd: Don't set chancnt
dmaengine: hidma: Don't set chancnt
dmaengine: plx_dma: Don't set chancnt
dmaengine: axi-dmac: Don't set chancnt
dmaengine: dw-axi-dmac: Don't set chancnt
dmaengine: qcom: bam_dma: allow omitting num-{channels,ees}
dmaengine: dw-edma: Add HDMA DebugFS support
dmaengine: dw-edma: Add support for native HDMA
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation
dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops
dmaengine: ste_dma40: use proper format string for resource_size_t
dmaengine: make QCOM_HIDMA depend on HAS_IOMEM
dmaengine: ste_dma40: fix typo in enum documentation
dmaengine: ste_dma40: use correct print specfier for resource_size_t
MAINTAINERS: Add myself as the DW eDMA driver reviewer
MAINTAINERS: Add Manivannan to DW eDMA driver maintainers list
MAINTAINERS: Demote Gustavo Pimentel to DW EDMA driver reviewer
dmaengine: ti: k3-udma: Add support for J721S2 CSI BCDMA instance
dt-bindings: dma: ti: Add J721S2 BCDMA
dmaengine: ti: k3-psil-j721s2: Add PSI-L thread map for main CPSW2G
...
-----BEGIN PGP SIGNATURE-----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=xpTd
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Export pcie_retrain_link() for use outside ASPM
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up
- Work around link training failures (especially on the ASMedia
ASM2824 switch) by training first at 2.5GT/s and then attempting
higher rates
Resource management:
- When we coalesce host bridge windows, remove invalidated resources
from the resource tree so future allocations work correctly
Hotplug:
- Cancel bringup sequence if card is not present, to keep from
blinking Power Indicator indefinitely
- Reassign bridge resources if necessary for ACPI hotplug
Driver binding:
- Convert platform_device .remove() callbacks to return void instead
of a mostly useless int
Power management:
- Reduce wait time for secondary bus to be ready to speed up resume
- Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in
D3cold
- Call _REG when transitioning D-states so AML that uses the PCI
config space OpRegion works, which fixes some ASMedia GPIO
controllers after resume
Virtualization:
- Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM
hang when guest is rebooted
- Add function 1 DMA alias quirk for Marvell 88SE9235
Error handling:
- Unexport pci_save_aer_state() since it's only used in drivers/pci/
- Drop recommendation for drivers to configure AER Capability, since
the PCI core does this for all devices
ASPM:
- Disable ASPM on MFD function removal to avoid use-after-free
- Tighten up pci_enable_link_state() and pci_disable_link_state()
interfaces so they don't enable/disable states the driver didn't
specify
- Avoid link retraining race that can happen if ASPM sets link
control parameters while the link is in the midst of training for
some other reason
Endpoint framework:
- Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be
different from "PCI Endpoint NTB driver"
- Automatically create a function specific attributes group for
endpoint drivers to avoid reference counting issues
- Fix many EPC test issues
- Return pci_epf_type_add_cfs() error if EPF has no driver
- Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq()
MSI vector parameters
- Pass EPF device ID to driver probe functions
- Return -EALREADY if EPC has already been started/stopped
- Add linkdown notifier support and use it in qcom-ep
- Add Bus Master Enable event support and use it in qcom-ep
- Add Qualcomm Modem Host Interface (MHI) endpoint driver
- Add Layerscape PME interrupt handling to manage link-up
notification
Cadence PCIe controller driver:
- Wait for link retrain to complete when working around the J721E
i2085 erratum with Gen2 mode
Faraday FTPC100 PCI controller driver:
- Release clock resources on error paths
Freescale i.MX6 PCIe controller driver:
- Save and restore Root Port MSI control to work around hardware defect
Intel VMD host bridge driver:
- Reset VMD config register between soft reboots
- Capture pci_reset_bus() return value instead of printing junk when
it fails
Qualcomm PCIe controller driver:
- Add SDX65 endpoint compatible string to DT binding
- Disable register write access after init for IP v2.3.3, v2.9.0
- Use DWC helpers for enabling/disabling writes to DBI registers
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0
- Reuse v2.3.2 post-init sequence for v2.4.0
Renesas R-Car PCIe controller driver:
- Remove unused static pcie_base and pcie_dev
Rockchip PCIe controller driver:
- Remove writes to unused registers
- Write endpoint Device ID using correct register
- Assert PCI Configuration Enable bit after probe so endpoint
responds instead of generating Request Retry Status messages
- Poll waiting for PHY PLLs to lock
- Update RK3399 example DT binding to be valid
- Use RK3399 PCIE_CLIENT_LEGACY_INT_CTRL to generate INTx instead of
manually generating PCIe message
- Use multiple windows to avoid address translation conflicts
- Use u32 (not u16) when accessing 32-bit registers
- Hide MSI-X Capability, since RK3399 can't generate MSI-X
- Set endpoint controller required alignment to 256
Synopsys DesignWare PCIe controller driver:
- Wait for link to come up only if we've initiated link training
Miscellaneous:
- Add pci_clear_master() stub for non-CONFIG_PCI"
* tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
Documentation: PCI: correct spelling
PCI: vmd: Fix uninitialized variable usage in vmd_enable_domain()
PCI: xgene-msi: Convert to platform remove callback returning void
PCI: tegra: Convert to platform remove callback returning void
PCI: rockchip-host: Convert to platform remove callback returning void
PCI: mvebu: Convert to platform remove callback returning void
PCI: mt7621: Convert to platform remove callback returning void
PCI: mediatek-gen3: Convert to platform remove callback returning void
PCI: mediatek: Convert to platform remove callback returning void
PCI: iproc: Convert to platform remove callback returning void
PCI: hisi-error: Convert to platform remove callback returning void
PCI: dwc: Convert to platform remove callback returning void
PCI: j721e: Convert to platform remove callback returning void
PCI: brcmstb: Convert to platform remove callback returning void
PCI: altera-msi: Convert to platform remove callback returning void
PCI: altera: Convert to platform remove callback returning void
PCI: aardvark: Convert to platform remove callback returning void
PCI: rcar: Use correct product family name for Renesas R-Car
PCI: layerscape: Add the endpoint linkup notifier support
PCI: endpoint: pci-epf-vntb: Fix typo in comments
...
- Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be different
from "PCI Endpoint NTB driver" (Shunsuke Mie)
- Automatically create a function specific attributes group for endpoint
drivers to avoid reference counting issues (Damien Le Moal)
- Move and unexport pci_epf_type_add_cfs() (Damien Le Moal)
- Reinitialize EPF test DMA transfer completion before submitting it to
avoid losing the completion notification (Damien Le Moal)
- Fix EPF test DMA transfer completion detection (Damien Le Moal)
- Submit EPF test DMA transfers with dmaengine_submit(), not tx_submit()
(Damien Le Moal)
- Simplify EPF test read/write/copy functions (Damien Le Moal)
- Simplify EPF test "raise IRQ" interface (Damien Le Moal)
- Simplify EPF test IRQ command execution (Damien Le Moal)
- Improve EPF test command/status register handling (Damien Le Moal)
- Free IRQs before removing device (Damien Le Moal)
- Reinitialize IRQ completions for every test (Damien Le Moal)
- Don't write status in IRQ handler to avoid race (Damien Le Moal)
- Fix dma_chan direction in data transfer test (Yoshihiro Shimoda)
- Return pci_epf_type_add_cfs() error if EPF has no driver (Damien Le Moal)
- Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq() MSI
vector parameters (Manivannan Sadhasivam)
- Pass EPF device ID to driver probe functions (Manivannan Sadhasivam)
- Return -EALREADY if EPC has already been started/stopped (Manivannan
Sadhasivam)
- Add linkdown notifier support and use it in qcom-ep (Manivannan
Sadhasivam)
- Add Bus Master Enable event support and use it in qcom-ep (Manivannan
Sadhasivam)
- Add Qualcomm Modem Host Interface (MHI) endpoint driver (Manivannan
Sadhasivam)
- Add Layerscape PME interrupt handling to manage link-up notification
(Frank Li)
* pci/controller/endpoint:
PCI: layerscape: Add the endpoint linkup notifier support
PCI: endpoint: pci-epf-vntb: Fix typo in comments
MAINTAINERS: Add PCI MHI endpoint function driver under MHI bus
PCI: endpoint: Add PCI Endpoint function driver for MHI bus
PCI: qcom-ep: Add support for BME notification
PCI: qcom-ep: Add support for Link down notification
PCI: endpoint: Add BME notifier support
PCI: endpoint: Add linkdown notifier support
PCI: endpoint: Return error if EPC is started/stopped multiple times
PCI: endpoint: Pass EPF device ID to the probe function
PCI: endpoint: Add missing documentation about the MSI/MSI-X range
PCI: endpoint: Improve pci_epf_type_add_cfs()
PCI: endpoint: functions/pci-epf-test: Fix dma_chan direction
misc: pci_endpoint_test: Simplify pci_endpoint_test_msi_irq()
misc: pci_endpoint_test: Do not write status in IRQ handler
misc: pci_endpoint_test: Re-init completion for every test
misc: pci_endpoint_test: Free IRQs before removing the device
PCI: epf-test: Simplify transfers result print
PCI: epf-test: Simplify DMA support checks
PCI: epf-test: Cleanup request result handling
PCI: epf-test: Cleanup pci_epf_test_cmd_handler()
PCI: epf-test: Improve handling of command and status registers
PCI: epf-test: Simplify IRQ test commands execution
PCI: epf-test: Simplify pci_epf_test_raise_irq()
PCI: epf-test: Simplify read/write/copy test functions
PCI: epf-test: Use dmaengine_submit() to initiate DMA transfer
PCI: epf-test: Fix DMA transfer completion detection
PCI: epf-test: Fix DMA transfer completion initialization
PCI: endpoint: Move pci_epf_type_add_cfs() code
PCI: endpoint: Automatically create a function specific attributes group
PCI: endpoint: Fix a Kconfig prompt of vNTB driver
- Disable register write access after init for IP v2.3.3, v2.9.0
(Manivannan Sadhasivam)
- Use DWC helpers for enabling/disabling writes to DBI registers
(Manivannan Sadhasivam)
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0 (Manivannan Sadhasivam)
- Reuse v2.3.2 post-init sequence for v2.4.0 (Manivannan Sadhasivam)
-
* pci/controller/qcom:
PCI: qcom: Do not advertise hotplug capability for IP v2.1.0
PCI: qcom: Do not advertise hotplug capability for IP v1.0.0
PCI: qcom: Use post init sequence of IP v2.3.2 for v2.4.0
PCI: qcom: Do not advertise hotplug capability for IP v2.3.2
PCI: qcom: Do not advertise hotplug capability for IPs v2.3.3 and v2.9.0
PCI: qcom: Do not advertise hotplug capability for IPs v2.7.0 and v1.9.0
PCI: qcom: Disable write access to read only registers for IP v2.9.0
PCI: qcom: Use DWC helpers for modifying the read-only DBI registers
PCI: qcom: Disable write access to read only registers for IP v2.3.3
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the dwc drivers from always returning zero in the remove
callback to the void returning variant.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230321193208.366561-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Layerscape has PME interrupt, which can be used as linkup notifier. Set
CFG_READY bit of PEX_PF0_CONFIG to enable accesses from root complex when
linkup detected.
Link: https://lore.kernel.org/r/20230515151049.2797105-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support to pass BME (Bus Master Enable) notification to Endpoint
function driver so that the BME event can be processed by the function.
Link: https://lore.kernel.org/r/20230602114756.36586-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Add support to pass Link down notification to Endpoint function driver so
that the LINK_DOWN event can be processed by the function.
Link: https://lore.kernel.org/r/20230602114756.36586-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
SoCs making use of Qcom PCIe controller IP v2.1.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The post init sequence of IP v2.4.0 is same as v2.3.2. So let's reuse the
v2.3.2 sequence which now also disables hotplug capability of the
controller as it is not at all supported on any SoCs making use of this IP.
Link: https://lore.kernel.org/r/20230619150408.8468-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IPs v2.3.3 and v2.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot
and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's not set the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-6-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot and
suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
While at it, let's also add a newline after existing dw_pcie_dbi_ro_wr_en()
guard function to align with rest of the driver.
Link: https://lore.kernel.org/r/20230619150408.8468-4-manivannan.sadhasivam@linaro.org
Fixes: 0cf7c2efe8 ("PCI: qcom: Add IPQ60xx support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DWC core already exposes dw_pcie_dbi_ro_wr_{en/dis} helper APIs for
enabling and disabling the write access to read only DBI registers. So
let's use them instead of doing it manually.
Also, the existing code doesn't disable the write access when it's done.
This is also fixed now.
Link: https://lore.kernel.org/r/20230619150408.8468-3-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
Link: https://lore.kernel.org/r/20230619150408.8468-2-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org>
The imx6 PCI host controller suffers from a HW integration bug whereby
the MSI enable bit in the root port MSI capability enables/disables MSIs
interrupts for all downstream components in the PCI tree.
This requires, as implemented in
75cb8d20c1 ("PCI: imx: Enable MSI from downstream components")
that the root port MSI enable bit should be set in order for downstream
PCI devices MSIs to function.
The MSI enable bit programming might be lost during the suspend and
should be re-stored during resume.
Save the MSI control during suspend and restore it in resume.
Link: https://lore.kernel.org/r/1670479534-22154-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[lpieralisi@kernel.org: commit log]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
In dw_pcie_host_init() regardless of whether the link has been
started or not, the code waits for the link to come up. Even in
cases where start_link() is not defined the code ends up spinning
in a loop for 1 second. Since in some systems dw_pcie_host_init()
gets called during probe, this one second loop for each pcie
interface instance ends up extending the boot time.
Wait for the link up in only if the start_link() is defined.
Link: https://lore.kernel.org/r/20230412093425.3659088-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Sajid Dalvi <sdalvi@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The dw_edma_core_ops structure contains a set of the operations:
device IRQ numbers getter, CPU/PCI address translation. Based on the
functions semantics the structure name "dw_edma_plat_ops" looks more
descriptive since indeed the operations are platform-specific. The
"dw_edma_core_ops" name shall be used for a structure with the IP-core
specific set of callbacks in order to abstract out DW eDMA and DW HDMA
setups. Such structure will be added in one of the next commit in the
framework of the set of changes adding the DW HDMA device support.
Anyway the renaming was necessary to distinguish two types of
the implementation callbacks:
1. DW eDMA/hDMA IP-core specific operations: device-specific CSR
setups in one or another aspect of the DMA-engine initialization.
2. DW eDMA/hDMA platform specific operations: the DMA device
environment configs like IRQs, address translation, etc.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230520050854.73160-2-cai.huoqing@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to request DRAM bandwidth (BW) with Memory Interconnect
in Tegra234 SoC. The DRAM BW required for different modes depends on
the link speed (Gen-1/2/3/4) and width/lanes (x1/x2/x4/x8).
Currently, the DRAM frequency is always set to the maximum available
but that results in the highest power consumption.
The Memory Interconnect is a software feature which uses Interconnect
framework (ICC). It adds the capability for Memory Controller (MC)
clients to request bandwidth and therefore scale DRAM frequency
dynamically depending on the required link speed so that the DRAM
energy consumption can be optimized.
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add check to fix the possible array out of bounds violation by
making speed equal to GEN1_CORE_CLK_FREQ when its value is more
than the size of "pcie_gen_freq" array. This array has size of
four but possible speed (CLS) values are from "0 to 0xF". So,
"speed - 1" values are "-1 to 0xE".
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Link: https://lore.kernel.org/lkml/72b9168b-d4d6-4312-32ea-69358df2f2d0@nvidia.com/
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----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=HPXl
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Add pci_dev_for_each_resource() and pci_bus_for_each_resource()
iterators
PCIe native device hotplug:
- Fix AB-BA deadlock between reset_lock and device_lock
Power management:
- Wait longer for devices to become ready after resume (as we do for
reset) to accommodate Intel Titan Ridge xHCI devices
- Extend D3hot delay for NVIDIA HDA controllers to avoid
unrecoverable devices after a bus reset
Error handling:
- Clear PCIe Device Status after EDR since generic error recovery now
only clears it when AER is native
ASPM:
- Work around Chromebook firmware defect that clobbers Capability
list (including ASPM L1 PM Substates Cap) when returning from
D3cold to D0
Freescale i.MX6 PCIe controller driver:
- Install imprecise external abort handler only when DT indicates
PCIe support
Freescale Layerscape PCIe controller driver:
- Add ls1028a endpoint mode support
Qualcomm PCIe controller driver:
- Add SM8550 DT binding and driver support
- Add SDX55 DT binding and driver support
- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3
- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0
- Add DT "mhi" register region for supported SoCs
- Expose link transition counts via debugfs to help debug low power
issues
- Support system suspend and resume; reduce interconnect bandwidth
and turn off clock and PHY if there are no active devices
- Enable async probe by default to reduce boot time
Miscellaneous:
- Sort controller Kconfig entries by vendor"
* tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (56 commits)
PCI: xilinx: Drop obsolete dependency on COMPILE_TEST
PCI: mobiveil: Sort Kconfig entries by vendor
PCI: dwc: Sort Kconfig entries by vendor
PCI: Sort controller Kconfig entries by vendor
PCI: Use consistent controller Kconfig menu entry language
PCI: xilinx-nwl: Add 'Xilinx' to Kconfig prompt
PCI: hv: Add 'Microsoft' to Kconfig prompt
PCI: meson: Add 'Amlogic' to Kconfig prompt
PCI: Use of_property_present() for testing DT property presence
PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
...
Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to
match other PCIe drivers. Capitalize "Meson" to match other Meson Kconfig
prompts.
Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
- Use correct PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register for v2.7.0
(Manivannan Sadhasivam)
- Remove "PCIE20_" prefix from register definitions (Manivannan Sadhasivam)
- Sort registers and bitfield declarations (Manivannan Sadhasivam)
- Convert to GENMASK and FIELD_PREP (Manivannan Sadhasivam)
- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 (Manivannan
Sadhasivam)
- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 (Manivannan Sadhasivam)
- Rename qcom_pcie_config_sid_sm8250() to be non SM8250-specific
(Manivannan Sadhasivam)
- Add DT "mhi" register region for supported SoCs (Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug low power issues
(Manivannan Sadhasivam)
- Support system suspend and resume; reduce interconnect bandwidth and turn
off clock and PHY if there are no active devices (Manivannan Sadhasivam)
- Enable async probe by default to reduce boot time (Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as qcom DT binding maintainer, replacing
Stanimir Varbanov (Manivannan Sadhasivam)
- Add DT binding and driver support for Qcom SDX55 SoC (Manivannan
Sadhasivam)
- Add DT binding and driver support for SM8550 SoC (Abel Vesa)
- Document msi-map and msi-map-mask DT properties (Manivannan Sadhasivam)
* pci/controller/qcom:
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI: qcom: Expose link transition counts via debugfs
dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs
PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version
PCI: qcom: Use macros for defining total no. of clocks & supplies
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0
PCI: qcom: Use lower case for hex
PCI: qcom: Add missing macros for register fields
PCI: qcom: Use bitfield definitions for register fields
PCI: qcom: Sort and group registers and bitfield definitions
PCI: qcom: Remove PCIE20_ prefix from register definitions
PCI: qcom: Fix the incorrect register usage in v2.7.0 config
SM8550 requires two additional clocks for proper working.
Add these two clocks as optional clocks (as only required by this
platform) and compatible for this platform.
While at it, let's also rename the reset variable to "rst" from
"pci_reset" to match the existing naming preference.
Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
[lpieralisi@kernel.org: commit log rewording]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Add support for SDX55 SoC reusing the 1.9.0 config. The PCIe controller is
of version 1.10.0 but it is compatible with the 1.9.0 config. This SoC also
requires "sleep" clock which is added as an optional clock in the driver,
since it is not required on other SoCs.
Link: https://lore.kernel.org/r/20230308082424.140224-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Qcom PCIe RC driver waits for the PHY link to be up during the probe;
this consumes several milliseconds during boot.
Enable async probe by default so that other drivers can load in parallel
while this driver waits for the link to be up.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230320064644.5217-1-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
During the system suspend, vote for minimal interconnect bandwidth (1KiB)
to keep the interconnect path active for config access and also turn OFF
the resources like clock and PHY if there are no active devices connected
to the controller. For the controllers with active devices, the resources
are kept ON as removing the resources will trigger access violation during
the late end of suspend cycle as kernel tries to access the config space of
PCIe devices to mask the MSIs.
Also, it is not desirable to put the link into L2/L3 state as that
implies VDD supply will be removed and the devices may go into powerdown
state. This will affect the lifetime of storage devices like NVMe.
And finally, during resume, turn ON the resources if the controller was
truly suspended (resources OFF) and update the interconnect bandwidth
based on PCIe Gen speed.
Suggested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Link: https://lore.kernel.org/r/20230403154922.20704-2-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Dhruva Gole <d-gole@ti.com>
Qualcomm PCIe controllers have debug registers in the MHI region that
count PCIe link transitions. Expose them over debugfs to userspace to
help debug the low power issues.
Note that even though the registers are prefixed as PARF_, they don't
live under the "parf" register region. The register naming is following
the Qualcomm's internal documentation as like other registers.
While at it, let's arrange the local variables in probe function to follow
reverse XMAS tree order.
Link: https://lore.kernel.org/r/20230316081117.14288-20-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
qcom_pcie_config_sid_sm8250() function no longer applies only to SM8250.
So let's rename it to reflect the actual IP version and also move its
definition to keep it sorted as per IP revisions.
Link: https://lore.kernel.org/r/20230316081117.14288-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
To keep uniformity, let's use macros to define the total number of clocks
and supplies in qcom_pcie_resources_{2_7_0/2_9_0} structs.
Link: https://lore.kernel.org/r/20230316081117.14288-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.
The total number of resets supported is 12 but only ipq4019 is using all of
them.
Link: https://lore.kernel.org/r/20230316081117.14288-13-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
While at it, let's also move the qcom_pcie_resources_2_1_0 struct below
qcom_pcie_resources_1_0_0 to keep it sorted.
Link: https://lore.kernel.org/r/20230316081117.14288-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Some of the registers are changed using hardcoded bitfields without macros.
This provides no information on what the register setting is about. So add
the macros to those fields for making the code more understandable.
Link: https://lore.kernel.org/r/20230316081117.14288-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
To maintain uniformity throughout the driver and also to make the code
easier to read, let's make use of bitfield definitions for register fields.
Link: https://lore.kernel.org/r/20230316081117.14288-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Sorting the registers and their bit definitions will make it easier to add
more definitions in the future and it also helps in maintenance.
While at it, let's also group the registers and bit definitions separately
as done in the pcie-qcom-ep driver.
Link: https://lore.kernel.org/r/20230316081117.14288-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The PCIE part is redundant and 20 doesn't represent anything across the
SoCs supported now. So let's get rid of the prefix.
This involves adding the IP version suffix to one definition of
PARF_SLV_ADDR_SPACE_SIZE that defines offset specific to that version.
The other definition is generic for the rest of the versions.
Also, the register PCIE20_LNK_CONTROL2_LINK_STATUS2 is not used anywhere,
hence removed.
Link: https://lore.kernel.org/r/20230316081117.14288-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
commit bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
extended the fault handling code.
commit 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com
Fixes: bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
Fixes: 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
If CDM_CHECK is enabled (by the DT "snps,enable-cdm-check" property), 'val'
is overwritten by PCIE_PL_CHK_REG_CONTROL_STATUS initialization. Commit
ec7b952f45 ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check"
exists") did not account for further usage of 'val', so we wrote improper
values to PCIE_PORT_LINK_CONTROL when the CDM check is enabled.
Move the PCIE_PORT_LINK_CONTROL update to be completely after the
PCIE_PL_CHK_REG_CONTROL_STATUS register initialization.
[bhelgaas: commit log adapted from Serge's version]
Fixes: ec7b952f45 ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists")
Link: https://lore.kernel.org/r/20230310123510.675685-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Add PCIe EP mode support for ls1028a.
Link: https://lore.kernel.org/r/20230209151050.233973-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
pcie-kirin uses regmaps, and needs to pull them in; otherwise, with
CONFIG_PCIE_KIRIN=y and without CONFIG_REGMAP_MMIO pcie-kirin produces
a linker failure looking for __devm_regmap_init_mmio_clk().
Fixes: d19afe7be1 ("PCI: kirin: Use regmap for APB registers")
Link: https://lore.kernel.org/r/04636141da1d6d592174eefb56760511468d035d.1668410580.git.josh@joshtriplett.org
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
[lpieralisi@kernel.org: commit log and removed REGMAP select]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org # 5.16+
-----BEGIN PGP SIGNATURE-----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=/y4d
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
- Release previously-requested DW eDMA IRQs if request_irq() fails (Serge
Semin)
- Convert DW eDMA linked-list (ll) and data target (dt) from CPU-relative
addresses to PCI bus addresses (Serge Semin)
- Fix missing src/dst address for interleaved transfers (Serge Semin)
- Enforce the DW eDMA restriction that interleaved transfers must increment
src and dst addresses (Serge Semin)
- Fix some invalid interleaved transfer semantics (Serge Semin)
- Convert CPU-relative addresses to PCI bus addresses for eDMA engine
(Serge Semin)
- Drop chancnt initialization from dw-edma-core, since it is managed by the
dmaengine core, e.g., in dma_async_device_channel_register() (Serge Semin)
- Clean up bogus casting of debugfs_entries.reg addresses (Serge Semin)
- Ignore debugfs file/directory creation errors (Serge Semin)
- Allocate debugfs entries from the heap to prepare for multi-eDMA
platforms (Serge Semin)
- Simplify and rework register accessors to remove another obstacle to
multi-eDMA platforms (Serge Semin)
- Consolidate eDMA read/write channels in a single dma_device to simplify,
better reflect the hardware design, and avoid a debugfs complaint (Serge
Semin)
- Move eDMA-specific debugfs nodes into existing dmaengine subdirectory
(Serge Semin)
- Fix a readq_ch() truncation from 64 to 32 bits (Serge Semin)
- Use existing readq()/writeq rather than hand-coding new ones (Serge
Semin)
- Drop unnecessary data target region allocation in favor of existing
dw_edma_chip members (Serge Semin)
- Use parent device in eDMA controller name to prepare for multi-eDMA
platforms (Serge Semin)
- In addition to the existing MMIO accessors for linked list entries, add
support for ioremapped entries for use by eDMA in Root Ports or local
Endpoints (Serge Semin)
- Convert DW_EDMA_PCIE so it depends on DW_EDMA instead of selecting it
(Serge Semin)
- Allow DWC drivers to set streaming DMA masks larger than 32 bits;
previously both streaming and coherent DMA were limited to 32 bits
because some PCI devices only support coherent 32-bit DMA for MSI (Serge
Semin)
- Set 64-bit streaming and coherent DMA mask for the bt1 driver (Serge
Semin)
- Add DW Root Port and Endpoint controller support for eDMA (Serge Semin)
* pci/controller/dwc:
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
dmaengine: dw-edma: Skip cleanup procedure if no private data found
dmaengine: dw-edma: Replace chip ID number with device name
dmaengine: dw-edma: Drop DT-region allocation
dmaengine: dw-edma: Use non-atomic io-64 methods
dmaengine: dw-edma: Fix readq_ch() return value truncation
dmaengine: dw-edma: Use DMA engine device debugfs subdirectory
dmaengine: dw-edma: Join read/write channels into a single device
dmaengine: dw-edma: Move eDMA data pointer to debugfs node descriptor
dmaengine: dw-edma: Simplify debugfs context CSRs init procedure
dmaengine: dw-edma: Rename debugfs dentry variables to 'dent'
dmaengine: dw-edma: Convert debugfs descs to being heap-allocated
dmaengine: dw-edma: Add dw_edma prefix to debugfs nodes descriptor
dmaengine: dw-edma: Stop checking debugfs_create_*() return value
dmaengine: dw-edma: Drop unnecessary debugfs reg casts
dmaengine: dw-edma: Drop chancnt initialization
dmaengine: dw-edma: Add PCI bus address getter to the remote EP glue driver
dmaengine: dw-edma: Add CPU to PCI bus address translation
dmaengine: dw-edma: Fix invalid interleaved xfers semantics
dmaengine: dw-edma: Don't permit non-inc interleaved xfers
dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
dmaengine: dw-edma: Convert ll/dt phys address to PCI bus/DMA address
dmaengine: dw-edma: Release requested IRQs on failure
dmaengine: Fix dma_slave_config.dst_addr description
- Convert dra7xx to threaded IRQ handler (Manivannan Sadhasivam)
- Move tegra194 dw_pcie_ep_linkup() to threaded IRQ handler (Manivannan
Sadhasivam)
- Add a separate lock for the endpoint pci_epf list to avoid deadlock
while running callbacks (Manivannan Sadhasivam)
- Use callbacks instead of notifier chains to signal events from EPC to EPF
drivers (Manivannan Sadhasivam)
- Use link_up() callback in place of LINK_UP notifier (Manivannan
Sadhasivam)
* pci/endpoint:
PCI: endpoint: Use link_up() callback in place of LINK_UP notifier
PCI: endpoint: Use callback mechanism for passing events from EPC to EPF
PCI: endpoint: Use a separate lock for protecting epc->pci_epf list
PCI: tegra194: Move dw_pcie_ep_linkup() to threaded IRQ handler
PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ
Since the DW eDMA core now supports eDMA controllers embedded in locally
accessible DW PCIe Root Ports and Endpoints, register these controllers
when possible.
To do that the DW PCIe core driver needs to perform some preparations
first. First of all, it needs to find the eDMA controller CSRs base
address, whether they are accessible over the Port Logic or iATU unrolled
space. Afterwards it can try to auto-detect the eDMA controller
availability and number of read/write channels. If none are found the
procedure silently returns without error.
Secondly, the platform is supposed to provide either combined or
per-channel IRQ signals. If no valid IRQs set is found, the procedure
returns without error to be backward compatible with platforms where DW
PCIe controllers have eDMA but lack the IRQ description.
Finally, before actually probing the eDMA device we need to allocate LLP
items buffers. After that the DW eDMA can be registered. If registration is
successful, a message regarding the number of detected Read/Write eDMA
channels will be printed to the system as is done for the iATU settings.
Note: the DW PCI controller driver (either host or endpoint mode) is
currently always built-in, so if the DW eDMA core is built as a module
(CONFIG_DW_EDMA=m), eDMA controllers will not be registered even if the
dw-edma module is later loaded.
Link: https://lore.kernel.org/r/20230113171409.30470-28-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
The DW PCIe Root Port IP core is synthesized with the 64-bit AXI address
bus. Since the device is also equipped with the eDMA engine, explicitly
set the device DMA mask so DMA engine clients can allocate data buffers
anywhere in the 64-bit memory space.
Link: https://lore.kernel.org/r/20230113171409.30470-27-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The MSI target address must be in the lowest 4GB memory to support PCI
peripherals without 64-bit MSI support. Since the allocation is done from
DMA coherent memory, set only the coherent DMA mask, leaving the streaming
DMA mask alone.
Thus streaming DMA operations will work with no artificial limitations. It
will be specifically useful for the eDMA-capable controllers so the
corresponding DMA engine clients would map the DMA buffers with no need for
SWIOTLB for buffers allocated above 4GB.
Add a brief comment about the reason allocating the MSI target address
below 4GB.
Link: https://lore.kernel.org/r/20230113171409.30470-26-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Since 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are
used to identify modules. As a consequence, MODULE_LICENSE in non-modules
causes modprobe to misidentify the object file as a module when it is not,
and modprobe might succeed rather than failing with a suitable error
message.
For tristate modules that can be either built-in or loaded at runtime,
modprobe succeeds in both cases:
# modprobe ext4
[exit status zero if CONFIG_EXT4_FS=y or =m]
For boolean modules like the Standard Hot Plug Controller driver (shpchp)
that cannot be loaded at runtime, modprobe should always fail like this:
# modprobe shpchp
modprobe: FATAL: Module shpchp not found in directory /lib/modules/...
[exit status non-zero regardless of CONFIG_HOTPLUG_PCI_SHPC]
but prior to this commit, shpchp_core.c contained MODULE_LICENSE, so
"modprobe shpchp" silently succeeded when it should have failed.
Remove MODULE_LICENSE in files that cannot be built as modules.
[bhelgaas: commit log, squash]
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230216152410.4312-1-nick.alcock@oracle.com/
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
IPQ8074 has one Gen2 and one Gen3 port, with Gen2 port already supported.
Add compatible for Gen3 port which uses the same controller as IPQ6018.
Link: https://lore.kernel.org/r/20230113164449.906002-7-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement the new host_deinit() callback so that the PHY is powered off
and regulators and clocks are disabled also on late host-init errors.
Link: https://lore.kernel.org/r/20221017114705.8277-2-johan+linaro@kernel.org
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
dw_pcie_ep_linkup() may take more time to execute depending on the EPF
driver implementation. Calling this API in the hard IRQ handler is not
encouraged since the hard IRQ handlers are supposed to complete quickly.
So move the dw_pcie_ep_linkup() call to threaded IRQ handler.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
The "dra7xx-pcie-main" hard IRQ handler is just printing the IRQ status
and calling the dw_pcie_ep_linkup() API if LINK_UP status is set. But the
execution of dw_pcie_ep_linkup() depends on the EPF driver and may take
more time depending on the EPF implementation.
In general, hard IRQ handlers are supposed to return quickly and not block
for so long. Moreover, there is no real need of the current IRQ handler to
be a hard IRQ handler. So switch to the threaded IRQ handler for the
"dra7xx-pcie-main" IRQ.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
i.MX PCIe is one dual mode PCIe controller.
Add i.MX PCIe EP mode support here, and split the PCIe modes to the Root
Complex mode and Endpoint mode.
Link: https://lore.kernel.org/r/1673847684-31893-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
a474d3fbe2 ("PCI/MSI: Get rid of PCI_MSI_IRQ_DOMAIN") removed
PCI_MSI_IRQ_DOMAIN and changed all references to refer to PCI_MSI instead.
ba6ed462dc ("PCI: dwc: Add Baikal-T1 PCIe controller support")
independently added PCIE_BT1, depending on PCI_MSI_IRQ_DOMAIN.
Both commits appeared in v6.2-rc1, so the latter missed the conversion from
PCI_MSI_IRQ_DOMAIN to PCI_MSI. Update PCIE_BT1 to depend on PCI_MSI
instead.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20221215103452.23131-1-lukas.bulwahn@gmail.com
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
- New support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Updates:
- again a big pile of updates on qcom-qmp-* drivers following the
driver split and reorganization merged earlier
- Phy order of API calls documentation update
-----BEGIN PGP SIGNATURE-----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=4HRP
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"This tme we have again a big pile of qcom-qmp-* changes, one new
driver and bunch of new hardware support.
New hardware support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Qualcomm SC8280XP PCIe PHY support (including x4 mode)
- Fixed Qualcomm SC8280XP USB4-USB3-DP PHY DT bindings
Updates:
- A big pile of updates on qcom-qmp-* drivers following the driver
split and reorganization merged earlier
- Phy order of API calls documentation update"
* tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (174 commits)
phy: ti: phy-j721e-wiz: add j721s2-wiz-10g module support
dt-bindings: phy-j721e-wiz: add j721s2 compatible string
phy: use devm_platform_get_and_ioremap_resource()
phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY variant
phy: allwinner: phy-sun6i-mipi-dphy: Add a variant power-on hook
phy: allwinner: phy-sun6i-mipi-dphy: Set the enable bit last
phy: allwinner: phy-sun6i-mipi-dphy: Make RX support optional
dt-bindings: sun6i-a31-mipi-dphy: Add the A100 DPHY variant
dt-bindings: sun6i-a31-mipi-dphy: Add the interrupts property
phy: qcom-qmp-pcie: drop redundant clock allocation
phy: qcom-qmp-usb: drop redundant clock allocation
phy: qcom-qmp: drop unused type header
phy: qcom-qmp-usb: drop sc8280xp reference-clock source
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: drop reference-clock source
phy: qcom-qmp-combo: add support for updated sc8280xp binding
phy: qcom-qmp-combo: rename DP_PHY register pointer
phy: qcom-qmp-combo: rename common-register pointers
phy: qcom-qmp-combo: clean up DP clock callbacks
phy: qcom-qmp-combo: separate clock and provider registration
phy: qcom-qmp-combo: add clock registration helper
...
-----BEGIN PGP SIGNATURE-----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=KULr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Squash portdrv_{core,pci}.c into portdrv.c to ease maintenance and
make more things static.
- Make portdrv bind to Switch Ports that have AER. Previously, if
these Ports lacked MSI/MSI-X, portdrv failed to bind, which meant
the Ports couldn't be suspended to low-power states. AER on these
Ports doesn't use interrupts, and the AER driver doesn't need to
claim them.
- Assign PCI domain IDs using ida_alloc(), which makes host bridge
add/remove work better.
Resource management:
- To work better with recent BIOSes that use EfiMemoryMappedIO for
PCI host bridge apertures, remove those regions from the E820 map
(E820 entries normally prevent us from allocating BARs). In v5.19,
we added some quirks to disable E820 checking, but that's not very
maintainable. EfiMemoryMappedIO means the OS needs to map the
region for use by EFI runtime services; it shouldn't prevent OS
from using it.
PCIe native device hotplug:
- Build pciehp by default if USB4 is enabled, since Thunderbolt/USB4
PCIe tunneling depends on native PCIe hotplug.
- Enable Command Completed Interrupt only if supported to avoid user
confusion from lspci output that says this is enabled but not
supported.
- Prevent pciehp from binding to Switch Upstream Ports; this happened
because of interaction with acpiphp and caused devices below the
Upstream Port to disappear.
Power management:
- Convert AGP drivers to generic power management. We hope to remove
legacy power management from the PCI core eventually.
Virtualization:
- Fix pci_device_is_present(), which previously always returned
"false" for VFs, causing virtio hangs when unbinding the driver.
Miscellaneous:
- Convert drivers to gpiod API to prepare for dropping some legacy
code.
- Fix DOE fencepost error for the maximum data object length.
Baikal-T1 PCIe controller driver:
- Add driver and DT bindings.
Broadcom STB PCIe controller driver:
- Enable Multi-MSI.
- Delay 100ms after PERST# deassert to allow power and clocks to
stabilize.
- Configure Read Completion Boundary to 64 bytes.
Freescale i.MX6 PCIe controller driver:
- Initialize PHY before deasserting core reset to fix a regression in
v6.0 on boards where the PHY provides the reference.
- Fix imx6sx and imx8mq clock names in DT schema.
Intel VMD host bridge driver:
- Fix Secondary Bus Reset on VMD bridges, which allows reset of NVMe
SSDs in VT-d pass-through scenarios.
- Disable MSI remapping, which gets re-enabled by firmware during
suspend/resume.
MediaTek PCIe Gen3 controller driver:
- Add MT7986 and MT8195 support.
Qualcomm PCIe controller driver:
- Add SC8280XP/SA8540P basic interconnect support.
Rockchip DesignWare PCIe controller driver:
- Base DT schema on common Synopsys schema.
Synopsys DesignWare PCIe core:
- Collect DT items shared between Root Port and Endpoint (PERST GPIO,
PHY info, clocks, resets, link speed, number of lanes, number of
iATU windows, interrupt info, etc) to snps,dw-pcie-common.yaml.
- Add dma-ranges support for Root Ports and Endpoints.
- Consolidate DT resource retrieval for "dbi", "dbi2", "atu", etc. to
reduce code duplication.
- Add generic names for clocks and resets to encourage more
consistent naming across drivers using DesignWare IP.
- Stop advertising PTM Responder role for Endpoints, which aren't
allowed to be responders.
TI J721E PCIe driver:
- Add j721s2 host mode ID to DT schema.
- Add interrupt properties to DT schema.
Toshiba Visconti PCIe controller driver:
- Fix interrupts array max constraints in DT schema"
* tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (95 commits)
x86/PCI: Use pr_info() when possible
x86/PCI: Fix log message typo
x86/PCI: Tidy E820 removal messages
PCI: Skip allocate_resource() if too little space available
efi/x86: Remove EfiMemoryMappedIO from E820 map
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI: xilinx-nwl: Fix coding style violations
PCI: mvebu: Switch to using gpiod API
PCI: pciehp: Enable Command Completed Interrupt only if supported
PCI: aardvark: Switch to using devm_gpiod_get_optional()
dt-bindings: PCI: mediatek-gen3: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: mt7621: Add sentinel to quirks table
PCI: vmd: Fix secondary bus reset for Intel bridges
PCI: endpoint: pci-epf-vntb: Fix sparse ntb->reg build warning
PCI: endpoint: pci-epf-vntb: Fix sparse build warning for epf_db
PCI: endpoint: pci-epf-vntb: Replace hardcoded 4 with sizeof(u32)
PCI: endpoint: pci-epf-vntb: Remove unused epf_db_phy struct member
PCI: endpoint: pci-epf-vntb: Fix call pci_epc_mem_free_addr() in error path
...
Baikal-T1 SoC is equipped with DWC PCIe v4.60a host controller. It can be
trained to work up to Gen.3 speed over up to x4 lanes. The host controller
is attached to the DW PCIe 3.0 PCS via the PIPE-4 interface, which in its
turn is connected to the DWC 10G PHY. The whole system is supposed to be
fed up with four clock sources: DBI peripheral clock, AXI application
clocks and external PHY/core reference clock generating the 100MHz signal.
In addition to that the platform provide a way to reset each part of the
controller: sticky/non-sticky bits, host controller core, PIPE interface,
PCS/PHY and Hot/Power reset signal. The driver also provides a way to
handle the GPIO-based PERST# signal.
Note due to the Baikal-T1 MMIO peculiarity we have to implement the DBI
interface accessors which make sure the IO operations are dword-aligned.
Link: https://lore.kernel.org/r/20221113191301.5526-21-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Currently almost each platform driver uses its own resets and clocks
naming in order to get the corresponding descriptors. It makes the code
harder to maintain and comprehend especially seeing the DWC PCIe core main
resets and clocks signals set hasn't changed much for about at least one
major IP-core release. So in order to organize things around these signals
we suggest to create a generic interface for them in accordance with the
naming introduced in the DWC PCIe IP-core reference manual:
Application clocks:
- "dbi" - data bus interface clock (on some DWC PCIe platforms it's
referred as "pclk", "pcie", "sys", "ahb", "cfg", "iface",
"gio", "reg", "pcie_apb_sys");
- "mstr" - AXI-bus master interface clock (some DWC PCIe glue drivers
refer to this clock as "port", "bus", "pcie_bus",
"bus_master/master_bus/axi_m", "pcie_aclk");
- "slv" - AXI-bus slave interface clock (also called as "port", "bus",
"pcie_bus", "bus_slave/slave_bus/axi_s", "pcie_aclk",
"pcie_inbound_axi").
Core clocks:
- "pipe" - core-PCS PIPE interface clock coming from external PHY (it's
normally named by the platform drivers as just "pipe");
- "core" - primary clock of the controller (none of the platform drivers
declare such a clock but in accordance with the ref. manual
the devices may have it separately specified);
- "aux" - auxiliary PMC domain clock (it is named by some platforms as
"pcie_aux" and just "aux");
- "ref" - Generic reference clock (it is a generic clock source, which
can be used as a signal source for multiple interfaces, some
platforms call it as "ref", "general", "pcie_phy",
"pcie_phy_ref").
Application resets:
- "dbi" - Data-bus interface reset (it's CSR interface clock and is
normally called as "apb" though technically it's not APB but
DWC PCIe-specific interface);
- "mstr" - AXI-bus master reset (some platforms call it as "port", "apps",
"bus", "axi_m");
- "slv" - ABI-bus slave reset (some platforms call it as "port", "apps",
"bus", "axi_s").
Core resets:
- "non-sticky" - non-sticky CSR flags reset;
- "sticky" - sticky CSR flags reset;
- "pipe" - PIPE-interface (Core-PCS) logic reset (some platforms
call it just "pipe");
- "core" - controller primary reset (resets everything except PMC
module, some platforms refer to this signal as "soft",
"pci");
- "phy" - PCS/PHY block reset (strictly speaking it is normally
connected to the input of an external block, but the
reference manual says it must be available for the PMC
working correctly, some existing platforms call it
"pciephy", "phy", "link");
- "hot" - PMC hot reset signal (also called as "sleep");
- "pwr" - cold reset signal (can be referred as "pwr", "turnoff").
Bus reset:
- "perst" - PCIe standard signal used to reset the PCIe peripheral
devices.
As you can see each platform uses it's own naming for basically the same
set of the signals. In the framework of this commit we suggest to add a
set of the clocks and reset signals resources, corresponding names and
identifiers for each denoted entity. At current stage the platforms will
be able to use the provided infrastructure to automatically request all
these resources and manipulate with them in the Host/EP init callbacks.
Alas it isn't that easy to create a common cold/hot reset procedure due to
too many platform-specifics in the procedure, like the external flags
exposure and the delays requirement.
Link: https://lore.kernel.org/r/20221113191301.5526-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Since the iATU CSR region is now retrieved in the DW PCIe resources getter
there is no much benefits in the iATU detection procedures splitting up.
Therefore let's join the iATU unroll/viewport detection procedure with the
rest of the iATU parameters detection code. The resultant method will be
as coherent as before, while the redundant functions will be eliminated
thus producing more readable code.
Link: https://lore.kernel.org/r/20221113191301.5526-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently the DW PCIe Root Port and Endpoint CSR spaces are retrieved in
the separate parts of the DW PCIe core driver. It doesn't really make
sense since the both controller types have identical set of the core CSR
regions: DBI, DBI CS2 and iATU/eDMA. Thus we can simplify the DW PCIe Host
and EP initialization methods by moving the platform-specific registers
space getting and mapping into a common method. It gets to be even more
justified seeing the CSRs base address pointers are preserved in the
common DW PCIe descriptor. Note all the OF-based common DW PCIe settings
initialization will be moved to the new method too in order to have a
single function for all the generic platform properties handling in single
place.
A nice side-effect of this change is that the pcie-designware-host.c and
pcie-designware-ep.c drivers are cleaned up from all the direct dw_pcie
storage modification, which makes the DW PCIe core, Root Port and Endpoint
modules more coherent.
Link: https://lore.kernel.org/r/20221113191301.5526-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Since in addition to the already available iATU unrolled mapping we are
about to add a few more DW PCIe platform-specific capabilities (CDM-check
and generic clocks/resets resources) let's add a generic interface to set
and get the flags indicating their availability. The new interface shall
improve maintainability of the platform-specific code.
Link: https://lore.kernel.org/r/20221113191301.5526-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In accordance with the generic PCIe Root Port DT-bindings the "dma-ranges"
property has the same format as the "ranges" property. The only difference
is in their semantics. The "dma-ranges" property describes the PCIe-to-CPU
memory mapping in opposite to the CPU-to-PCIe mapping of the "ranges"
property. Even though the DW PCIe controllers are normally equipped with
the internal Address Translation Unit which inbound and outbound tables
can be used to implement both properties semantics, it was surprising for
me to discover that the host-related part of the DW PCIe driver currently
supports the "ranges" property only while the "dma-ranges" windows are
just ignored. Having the "dma-ranges" supported in the driver would be
very handy for the platforms, that don't tolerate the 1:1 CPU-PCIe memory
mapping and require a customized PCIe memory layout. So let's fix that by
introducing the "dma-ranges" property support.
First of all we suggest to rename the dw_pcie_prog_inbound_atu() method to
dw_pcie_prog_ep_inbound_atu() and create a new version of the
dw_pcie_prog_inbound_atu() function. Thus we'll have two methods for the
RC and EP controllers respectively in the same way as it has been
developed for the outbound ATU setup methods.
Secondly aside with the memory window index and type the new
dw_pcie_prog_inbound_atu() function will accept CPU address, PCIe address
and size as its arguments. These parameters define the PCIe and CPU memory
ranges which will be used to setup the respective inbound ATU mapping. The
passed parameters need to be verified against the ATU ranges constraints
in the same way as it is done for the outbound ranges.
Finally the DMA-ranges detected for the PCIe controller need to be
converted to the inbound ATU entries during the host controller
initialization procedure. It will be done in the framework of the
dw_pcie_iatu_setup() method. Note before setting the inbound ranges up we
need to disable all the inbound ATU entries in order to prevent unexpected
PCIe TLPs translations defined by some third party software like
bootloaders.
Link: https://lore.kernel.org/r/20221113191301.5526-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
What a zoo:
PCI_MSI
select GENERIC_MSI_IRQ
PCI_MSI_IRQ_DOMAIN
def_bool y
depends on PCI_MSI
select GENERIC_MSI_IRQ_DOMAIN
Ergo PCI_MSI enables PCI_MSI_IRQ_DOMAIN which in turn selects
GENERIC_MSI_IRQ_DOMAIN. So all the dependencies on PCI_MSI_IRQ_DOMAIN are
just an indirection to PCI_MSI.
Match the reality and just admit that PCI_MSI requires
GENERIC_MSI_IRQ_DOMAIN.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.467556921@linutronix.de
This patch switches the driver away from legacy gpio/of_gpio API to
gpiod API, and removes use of of_get_named_gpio_flags() which I want to
make private to gpiolib.
Link: https://lore.kernel.org/r/20220906204301.3736813-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When the PHY is the reference clock provider then it must be initialized
and powered on before the reset on the client is deasserted, otherwise
the link will never come up. The order was changed in cf236e0c0d.
Restore the correct order to make the driver work again on boards where
the PHY provides the reference clock. This also changes the order for
boards where the Soc is the PHY reference clock divider, but this
shouldn't do any harm.
Link: https://lore.kernel.org/r/20221101095714.440001-1-s.hauer@pengutronix.de
Fixes: cf236e0c0d ("PCI: imx6: Do not hide PHY driver callbacks and refine the error handling")
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
On Qualcomm platforms like SC8280XP and SA8540P, interconnect bandwidth
must be requested before enabling interconnect clocks.
Add basic support for managing an optional "pcie-mem" interconnect path
by setting a low constraint before enabling clocks and updating it after
the link is up.
Note that it is not possible for a controller driver to set anything but
a maximum peak bandwidth as expected average bandwidth will vary with
use case and actual use (and power policy?). This very much remains an
unresolved problem with the interconnect framework.
Also note that no constraint is set for the SC8280XP/SA8540P "cpu-pcie"
path for now as it is not clear what an appropriate constraint would be
(and the system does not crash when left unspecified).
Link: https://lore.kernel.org/r/20221102090705.23634-3-johan+linaro@kernel.org
Fixes: 70574511f3 ("PCI: qcom: Add support for SC8280XP")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Many host controller drivers #include <linux/of_irq.h> even though they
don't need it. Remove the unnecessary #includes.
Link: https://lore.kernel.org/r/20221031153954.1163623-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <roy.zang@nxp.com>
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Dual mode DesignWare PCIe IP has PTM capability enabled (if supported) even
in the EP mode. The PCIe compliance for the EP mode expects PTM
capabilities (ROOT_CAPABLE, RES_CAPABLE, CLK_GRAN) be disabled.
Hence disable PTM for the EP mode.
Link: https://lore.kernel.org/r/20220919143340.4527-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
commit aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being
used in the EP mode.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20220927092207.161501-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being
used in the RC mode.
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20220927092207.161501-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- List platforms that use a single MSI host interrupt in qcom DT (Johan
Hovold)
- Add SC8280XP, SA8540P support to qcom DT binding and driver(Johan Hovold)
- Make all optional clocks truly optional in the driver (Johan Hovold)
- Rename per-IP structs to reflect the IP version (Johan Hovold)
- Sort device ID match table by compatible string (Johan Hovold)
- Add MODULE_DEVICE_TABLE to enable module autoloading (Dmitry Baryshkov)
- Drop the unused .post_deinit() callback (Johan Hovold)
- Rely on DT for clock information instead of hard-coding it in the driver
(Manivannan Sadhasivam)
- Disable IRQs when removing driver to avoid spurious IRQs later
(Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug issues with
low-power states (Manivannan Sadhasivam)
- Gate Master AXI clock to the MHI bus while in L1 substates to save power
(Manivannan Sadhasivam)
- Disable Master AXI clock to save power when there is no traffic on PCIe
(Manivannan Sadhasivam)
- Make the "PERST separation" debug feature optional in the DT and the
driver (Manivannan Sadhasivam)
- Define clocks to be per-platform in DT to prepare for future SoCs
(Manivannan Sadhasivam)
- Add SM8450 SoC support (Manivannan Sadhasivam)
- Check for platform_get_resource_byname() to avoid a NULL pointer
dereference (Yang Yingliang)
* pci/qcom:
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
PCI: qcom: Rename host-init error label
PCI: qcom: Drop unused post_deinit callback
PCI: qcom-ep: Add MODULE_DEVICE_TABLE
PCI: qcom: Sort device-id table
PCI: qcom: Clean up IP configurations
PCI: qcom: Make all optional clocks optional
PCI: qcom: Add support for SA8540P
PCI: qcom: Add support for SC8280XP
dt-bindings: PCI: qcom: Add SA8540P to binding
dt-bindings: PCI: qcom: Add SC8280XP to binding
dt-bindings: PCI: qcom: Enumerate platforms with single msi interrupt
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL
pointer, which causes a NULL pointer dereference when it is used in
qcom_pcie_perst_deassert().
Check the return value to prevent it.
Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller
driver. The driver uses the same config as the existing SDX55 chipset,
so additional settings are not required.
Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PERST separation is an optional debug feature used to collect the crash
dump from the PCIe endpoint devices by the PCIe host when the endpoint
crashes. This feature keeps the PCIe link up by separating the PCIe IP
block from the SoC reset logic.
Make the property optional in the driver.
Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Master AXI clock can be disabled when it is not used i.e., when there
is no traffic on the PCIe bus. This helps to save power during idle state.
[bhelgaas: tidy and wrap comment]
Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Qualcomm PCIe controllers have debug registers in the MMIO region
that count PCIe link transitions. Expose them over debugfs to
userspace to help debug the low power issues.
Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Disable the Global and PERST IRQs during driver remove to avoid getting
spurious IRQs after resource deallocation.
Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
In the qcom_pcie_ep_get_resources() function, dev pointer is already
cached in a local variable. So let's make use of it instead of getting
the dev pointer again from pdev struct.
Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Generally, device drivers should just rely on the platform data like
devicetree to supply the clocks required for the functioning of the
peripheral. There is no need to hardcode the clk info in the driver.
So get rid of the static clk info and obtain the platform supplied
clks.
The total number of clocks supplied is obtained using the
devm_clk_bulk_get_all() API and used for the rest of the clk_bulk_ APIs.
Link: https://lore.kernel.org/r/20220914075350.7992-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.
Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Add i.MX8MP PCIe support.
To avoid codes duplication when find the syscon regmap, add the iomux
gpr syscon compatible into drvdata.
Link: https://lore.kernel.org/r/1662109086-15881-8-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Link: https://lore.kernel.org/r/20220830183310.48541-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Drop the unused and confusingly named post_deinit callback that was
added for the now removed pipe clock handling.
If ever needed we can add back a callback named pre_deinit (or perhaps
rather pre_phy_power_off) instead.
Link: https://lore.kernel.org/r/20220928155421.21660-2-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Re-work the msi_msg DMA allocation logic to use dmam_alloc_coherent() which
uses the coherent DMA mask to try to return an allocation within the DMA
mask limits. With that, we now can drop the msi_page parameter in struct
dw_pcie_rp. This allows kernel configurations that disable ZONE_DMA32 to
continue supporting a 32-bit DMA mask. Without this patch, the PCIe host
device will fail to probe when ZONE_DMA32 is disabled.
Link: https://lore.kernel.org/r/20220825235404.4132818-2-willmcvicker@google.com
Fixes: 35797e672f ("PCI: dwc: Fix MSI msi_msg DMA mapping")
Reported-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Sort the device-id table entries alphabetically by compatible string to
make it easier to find entries and add new ones.
Link: https://lore.kernel.org/r/20220714071348.6792-9-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The various IP versions have different configurations that are encoded
in separate sets of operation callbacks. Currently, there is no need for
also maintaining corresponding sets of data parameters, but it is
conceivable that these may again be found useful (e.g. to implement
minor variations of the operation callbacks).
Rename the default configuration structures after the IP version they
apply to so that they can more easily be reused by different SoCs.
Note that SoC specific configurations can be added later if need arises
(e.g. cfg_sc8280xp).
Link: https://lore.kernel.org/r/20220714071348.6792-8-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The kernel is not a devicetree validator and does not need to re-encode
information which is already available in the devicetree.
This is specifically true for the optional PCIe clocks, some of which
are really interconnect clocks.
Treat also the 2.7.0 optional clocks as truly optional instead of
maintaining a list of clocks per compatible (including two compatible
strings for the two identical controllers on sm8450) just to validate
the devicetree.
Link: https://lore.kernel.org/r/20220714071348.6792-7-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The SA8540P platform has five PCIe controllers: two 4-lane, two 2-lane
and one 1-lane.
Add a new "qcom,pcie-sa8540p" compatible string and reuse the 1.9.0 ops.
Note that like for SC8280XP, the SA8540P controllers need two or three
interconnect clocks to be enabled.
Link: https://lore.kernel.org/r/20220714071348.6792-6-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The SC8280XP platform has seven PCIe controllers: two used with USB4,
two 4-lane, two 2-lane and one 1-lane.
Add a new "qcom,pcie-sc8280xp" compatible string and reuse the 1.9.0
ops.
Note that the SC8280XP controllers need two or three interconnect
clocks to be enabled. Model these as optional clocks to avoid encoding
devicetree data in the PCIe driver.
Note that the same could be done for the SM8450 interconnect clocks and
possibly also for the TBU clocks.
Link: https://lore.kernel.org/r/20220714071348.6792-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
and NTB EndPoint Function (EPF) support and the various fixes from that
being in -next for Linux v5.20
-----BEGIN PGP SIGNATURE-----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=DAah
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
ntb_mw_set_trans() will set memory map window after endpoint function
driver bind. The inbound map address need be updated dynamically when
using NTB by PCIe Root Port and PCIe Endpoint connection.
Checking if iatu already assigned to the BAR, if yes, using assigned iatu
number to update inbound address map and skip set BAR's register.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
- Drop of_match_ptr() to avoid unused variables when CONFIG_OF is unset
(Bjorn Helgaas)
- Fix ARM pci_remap_iospace() when CONFIG_MMU unset to avoid build errors
(Pali Rohár)
* pci/misc:
PCI/ACPI: Update link to PCI firmware specification
PCI: Drop of_match_ptr() to avoid unused variables
- Convert to new *_PM_OPS macros to avoid need for "#ifdef CONFIG_PM_SLEEP"
or "__maybe_unused" (Bjorn Helgaas)
* pci/ctrl/pm-ops:
PCI: Convert to new *_PM_OPS macros
- Fix tegra_pcie_config_ep() power management in error path (Miaoqian Lin)
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and Endpoint
mode (Vidya Sagar)
- Disable MSI for Tegra234 Root Ports so they use INTx for all events (PCIe
doesn't allow mixing INTx and MSI/MSI-X) (Vidya Sagar)
- Search for Vendor-Specific RAS-DEC capability instead of hard-coding
offset (Vidya Sagar)
- Fix unintentional APPL_INTR_STATUS_L0 value overwrite in Root Port
interrupt handling (Vidya Sagar)
- Clear Bandwidth Management interrupt status bit to avoid interrupt storm
(Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix offset when clearing bit in Data Link Feature capability (Vidya
Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar)
* pci/ctrl/tegra194:
PCI: tegra194: Add Tegra234 PCIe support
PCI: tegra194: Extend Endpoint mode support
PCI: tegra194: Fix link up retry sequence
PCI: tegra194: Clean up the exit path for Endpoint mode
PCI: tegra194: Enable support for 256 Byte payload
PCI: tegra194: Clear bandwidth management status
PCI: tegra194: Fix Root Port interrupt handling
PCI: tegra194: Find RAS DES PCIe capability offset
Revert "PCI: tegra194: Rename tegra_pcie_dw to tegra194_pcie"
PCI: Disable MSI for Tegra234 Root Ports
dt-bindings: PCI: tegra234: Add schema for tegra234 Endpoint mode
dt-bindings: PCI: tegra234: Add schema for tegra234 Root Port mode
dt-bindings: PCI: tegra194: Convert to json-schema
PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
# drivers/pci/controller/dwc/pcie-tegra194.c
- Add PHY clock source implementation (Dmitry Baryshkov)
- Use new clk_regmap_phy_mux_ops for gcc-sm8450 and gcc-sc7280 PCIe pipe
clocks (Dmitry Baryshkov)
- Set up rev 2.1.0 PARF_PHY before enabling clocks (Christian Marangi)
- Power on PHY before accessing IPQ8074 DBI registers to avoid boot hangs
(Robert Marko)
- Power on PHY before accessing DBI registers on all variants for
consistency (Robert Marko)
- Remove unnecessary pipe_clk handling since this is done in PHY drivers
(Dmitry Baryshkov)
- Drop manual pipe_clk_src handling (Dmitry Baryshkov)
- Move GEN3_RELATED DBI definitions to common dwc header (Baruch Siach)
- Define slot capabilities using generic PCI_EXP_SLTCAP_* macros (Baruch
Siach)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Fix DT description typo (Baruch Siach)
- Fix DT "compatibles" typo (Johan Hovold)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
* pci/ctrl/qcom:
PCI: qcom: Allow ASPM L1 and substates for 2.7.0
dt-bindings: PCI: qcom: Fix reset conditional
dt-bindings: PCI: qcom: Fix description typo
PCI: qcom: Add IPQ60xx support
PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
PCI: dwc: Move GEN3_RELATED DBI definitions to common header
PCI: qcom: Drop manual pipe_clk_src handling
PCI: qcom: Remove unnecessary pipe_clk handling
PCI: qcom: Power on PHY before DBI register accesses
PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: regmap: add PHY clock source implementation
- Factor out ref clock disables to match enables (Bjorn Helgaas)
- Collect clock enables in imx6_pcie_clk_enable() (Richard Zhu)
- Propagate regulator and clock errors back to .host_init() caller (Richard
Zhu)
- Disable i.MX6QDL clock when disabling ref clocks (Richard Zhu)
- Call host init function directly in resume instead of duplicating the
code (Richard Zhu)
- Turn off regulators when suspending (Richard Zhu)
- Make link being down a non-fatal error so probe doesn't fail (Richard
Zhu)
- Start link in resume only if it was up before suspend to reduce resume
time (Richard Zhu)
- Move PHY init and power-on out of clock- and reset-related functions
(Richard Zhu)
- Rework suspend callback to be more symmetric with resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
* pci/ctrl/imx6:
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers. To
make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN
properly when writing the DBI registers.
Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions.
Encapsulate clocks, regulators disables and PHY uninitialization into
imx6_pcie_host_exit().
To keep suspend/resume symmetric as much as possible, invoke these two
new created functions in suspend callback.
To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable()
to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move the imx6_pcie_ltssm_disable() earlier and place it just behind the
imx6_pcie_ltssm_enable(), since it might not be only used by suspend
callback directly.
To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ
switch cases in imx6_pcie_ltssm_disable().
Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
imx6_pcie_clk_enable() enables clocks in the order:
pcie_phy
pcie_bus
pcie
imx6_pcie_enable_ref_clk
Change imx6_pcie_clk_disable() to disable them in the reverse order.
Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move the phy_power_on() to host_init from imx6_pcie_clk_enable().
Move the phy_init() to host_init from imx6_pcie_deassert_core_reset().
Refine the error handling in imx6_pcie_host_init() accordingly.
Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
i.MX PCIe doesn't support hotplug. During resume, only start PCIe link
training when the link was up before system suspend to avoid the long
latency in the link training period.
Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the PCIe link is down, return zero from imx6_pcie_start_link() so the
driver will probe successfully.
Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move regulator enable out of imx6_pcie_deassert_core_reset(), since the
regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver should undo any enables it did itself. The regulator disable
shouldn't be basing decisions on regulator_is_enabled().
Move the regulator_disable to the suspend function, turn off regulator when
the system is in suspend mode.
Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Call imx6_pcie_host_init() instead of duplicating codes in resume. Note
that this also means we do MPLL setup again during resume, which we didn't
do before.
[bhelgaas: add MPLL setup note, pointed out by Lucas]
Link: https://lore.kernel.org/r/1657783869-19194-10-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Since dw_pcie_host_init() checks for errors from ops->host_init(),
check for errors when enabling power regulators and clocks and return them.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1657783869-19194-8-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Encapsulate the i.MX PCIe clock enable operations into one standalone
function, imx6_pcie_clk_enable(). No functional change intended.
[bhelgaas: split pure code moves into separate patches]
Link: https://lore.kernel.org/r/1657783869-19194-7-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The PCIe ref clocks are specific to different variants. The enables are
already split out into imx6_pcie_enable_ref_clk(), but the disables were
combined with the more generic bus/phy/pcie clock disables in
imx6_pcie_clk_disable().
Split out the variant-specific disables into imx6_pcie_disable_ref_clk() to
match imx6_pcie_enable_ref_clk().
No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-6-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_clk_disable() earlier to be near other clock-related
functions. No functional change intended.
[bhelgaas: reorder patch so pure moves are earlier]
Link: https://lore.kernel.org/r/1657783869-19194-5-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move imx6_pcie_enable_ref_clk() earlier so it's not in the middle between
imx6_pcie_assert_core_reset() and imx6_pcie_deassert_core_reset(). No
functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-4-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and
imx6_setup_phy_mpll() earlier with other PHY-related code. No functional
change intended.
Link: https://lore.kernel.org/r/1657783869-19194-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Move imx6_pcie_grp_offset() and imx6_pcie_configure_type() earlier in the
file since they depend on nothing and are used by several other functions
that will be moved earlier. No functional change intended.
Link: https://lore.kernel.org/r/1657783869-19194-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
