The helper devm_clk_bulk_get_all_enable() missed to return the number of
clocks stored in the clk_bulk_data table referenced by the clks
argument and, therefore, will be dropped.
Use the newly introduced devm_clk_bulk_get_all_enabled() variant
instead, which is consistent with devm_clk_bulk_get_all() in terms of
the returned value:
> 0 if one or more clocks have been stored
= 0 if there are no clocks
< 0 if an error occurred
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20241217-clk_bulk_ena_fix-v5-2-aafbbb245155@collabora.com
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
- Enable MSI interrupts if 'global' IRQ is supported, since a previous
commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a
and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml
DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom
platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the link
comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to
support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map'
DT property and doesn't need BDF-to-SID translation (Qiang Yu)
* pci/controller/qcom:
PCI: qcom: Disable ASPM L0s for X1E80100
PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC
dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
PCI: qcom: Add support for IPQ9574
dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller
PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()
PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root Complex
mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we can do
(Kishon Vijay Abraham I)
* pci/controller/keystone:
PCI: keystone: Add link up check to ks_pcie_other_map_bus()
PCI: keystone: Set mode as Root Complex for "ti,keystone-pcie" compatible
- Fix suspend/resume support on i.MX6QDL, which has a hardware erratum that
prevents use of L2 (Stefan Eichenberger)
* pci/controller/imx6:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
- Clear outbound address on unmap so dw_pcie_find_index() won't match an
ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when testing
for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Fix advertised resizable BAR size regression
PCI: dwc: Use of_property_present() for non-boolean properties
PCI: dwc: endpoint: Clear outbound address on unmap
- Add pci_epc_function_is_valid() to avoid repeating common validation
checks (Damien Le Moal)
- Skip attempts to allocate from endpoint controller memory window if the
requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to handle
controller-specific size and alignment constraints, and add test cases to
the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can observe
DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent (Niklas
Cassel)
- Remove superfluous 'return' from pci_epf_test_clean_dma_chan() (Wang
Jiang)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks 'mmio' DT
property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid use-after-free
(Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when removing
the secondary controller associated with an NTB (Zijun Hu)
- Fix pci_epc_map map_size kerneldoc (Rick Wertenbroek)
* pci/endpoint:
PCI: endpoint: Fix pci_epc_map map_size kerneldoc string
PCI: endpoint: Clear secondary (not primary) EPC in pci_epc_remove_epf()
PCI: endpoint: Fix PCI domain ID release in pci_epc_destroy()
PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio'
PCI: endpoint: Remove surplus return statement from pci_epf_test_clean_dma_chan()
PCI: dwc: ep: Use align addr function for dw_pcie_ep_raise_{msi,msix}_irq()
PCI: endpoint: test: Synchronously cancel command handler work
PCI: dwc: endpoint: Implement the pci_epc_ops::align_addr() operation
PCI: endpoint: test: Use pci_epc_mem_map/unmap()
PCI: endpoint: Update documentation
PCI: endpoint: Introduce pci_epc_mem_map()/unmap()
PCI: endpoint: Improve pci_epc_mem_alloc_addr()
PCI: endpoint: Introduce pci_epc_function_is_valid()
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Link: https://lore.kernel.org/r/20241104190714.275977-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use the dw_pcie_ep_align_addr() function to calculate the alignment in
dw_pcie_ep_raise_{msi,msix}_irq() instead of open coding the same.
Link: https://lore.kernel.org/r/20241017132052.4014605-6-cassel@kernel.org
Link: https://lore.kernel.org/r/20241104205144.409236-2-cassel@kernel.org
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: squashed patch that fixes memory map sizes]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b2390634 ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
commit 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x
Platforms") introduced configuring "enum dw_pcie_device_mode" as part of
device data ("struct ks_pcie_of_data"). However it failed to set the
mode for "ti,keystone-pcie" compatible.
Since the mode defaults to "DW_PCIE_UNKNOWN_TYPE", the following error
message is displayed for the v3.65a controller:
"INVALID device type 0"
Despite the driver probing successfully, the controller may not be
functional in the Root Complex mode of operation.
So, set the mode as Root Complex for "ti,keystone-pcie" compatible to
fix this.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Link: https://lore.kernel.org/r/20240524105714.191642-2-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
4e92355e1f
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
Link: https://lore.kernel.org/r/20241030103250.83640-1-eichest@gmail.com
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
The function dw_pcie_prog_outbound_atu() used to program outbound ATU
entries for mapping RC PCI addresses to local CPU addresses does not
allow PCI addresses that are not aligned to the value of region_align
of struct dw_pcie. This value is determined from the iATU hardware
registers during probing of the iATU (done by dw_pcie_iatu_detect()).
This value is thus valid for all DWC PCIe controllers, and valid
regardless of the hardware configuration used when synthesizing the
DWC PCIe controller.
Implement the ->align_addr() endpoint controller operation to allow
this mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/linux-pci/20241012113246.95634-7-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241015090712.112674-1-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241017132052.4014605-5-cassel@kernel.org
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[mani: squashed the patch that changed phy_addr_t to u64]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: squashed patch that updated the pci_size variable]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the cfg_1_9_0 which is being used for X1E80100 doesn't disable
ASPM L0s. However, hardware team recommends to disable L0s as the PHY init
sequence is not tuned support L0s. Hence reuse cfg_sc8280xp for X1E80100.
Note that the config_sid() callback is not present in cfg_sc8280xp, don't
concern about this because config_sid() callback is originally a no-op
for X1E80100.
Fixes: 6d0c39324c ("PCI: qcom: Add X1E80100 PCIe support")
Link: https://lore.kernel.org/r/20241101030902.579789-5-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9
The SC8280XP PCIe devicetree nodes do not specify an 'iommu-map' so
the config_sid() callback is effectively a no-op.
Hence introduce a new ops struct, namely ops_1_21_0 which is same as
ops_1_9_0 except that it doesn't have config_sid() callback to clean
it up.
Link: https://lore.kernel.org/r/20241101030902.579789-4-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of pex_ep_event_pex_rst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the tegra194 endpoint SoCs supported as of now depend on the refclk
from the host for keeping the controller operational. Due to this
limitation, any access to the hardware registers in the absence of refclk
will result in a whole endpoint crash. Unfortunately, most of the
controller cleanups require accessing the hardware registers (like eDMA
cleanup performed in dw_pcie_ep_cleanup(), etc...). So these cleanup
functions can cause the crash in the endpoint SoC once host asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host.
Thus, fix this crash by moving the controller cleanups to the start of
the pex_ep_event_pex_rst_deassert() function. This function is called
whenever the host has deasserted PERST# and it is guaranteed that the
refclk would be active at this point. So at the start of this function
(after enabling resources) the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-2-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of qcom_pcie_perst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the Qcom endpoint SoCs supported as of now depend on the refclk from
the host for keeping the controller operational. Due to this limitation,
any access to the hardware registers in the absence of refclk will result
in a whole endpoint crash. Unfortunately, most of the controller cleanups
require accessing the hardware registers (like eDMA cleanup performed in
dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup
functions are currently causing the crash in the endpoint SoC once host
asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host (as I was told by the Qcom engineers).
Thus, fix this crash by moving the controller cleanups to the start of
the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is
called whenever the host has deasserted PERST# and it is guaranteed that
the refclk would be active at this point. So at the start of this function
(after enabling resources), the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, if 'Global IRQ' is supported by the platform, only the Link up
interrupt is enabled in the PARF_INT_ALL_MASK register. This masks MSIs
on some platforms. The MSI bits in PARF_INT_ALL_MASK register are enabled
by default in the hardware, but commit 4581403f67 ("PCI: qcom: Enumerate
endpoints based on Link up event in 'global_irq' interrupt") disabled them
and enabled only the Link up interrupt. While MSI continued to work on the
SM8450 platform that was used to test the offending commit, on other
platforms like SM8250, X1E80100, MSIs are getting masked. And they require
enabling the MSI interrupt bits in the register to unmask (enable) the
MSIs.
Even though the MSI interrupt enable bits in PARF_INT_ALL_MASK are
described as 'diagnostic' interrupts in the internal documentation,
disabling them masks MSI on these platforms. Due to this, MSIs were not
reported to be received these platforms while supporting 'Global IRQ'.
So, enable the MSI interrupts along with the Link up interrupt in the
PARF_INT_ALL_MASK register if 'Global IRQ' is supported. This ensures that
the MSIs continue to work and also the driver is able to catch the Link
up interrupt for enumerating endpoint devices.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Closes: https://lore.kernel.org/linux-pci/9a692c98-eb0a-4d86-b642-ea655981ff53@kernel.org/
Link: https://lore.kernel.org/r/20241007051255.4378-1-manivannan.sadhasivam@linaro.org
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SL7
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Qiang Yu <quic_qianyu@quicinc.com>
Clear the address mapped (outbound_addr array) in dw_pcie_ep_unmap_addr(),
to ensure that dw_pcie_find_index() does not match an ATU index that was
already unmapped.
This is in addition to clearing the ATU index bit in ob_window_map.
Link: https://lore.kernel.org/linux-pci/20241004141000.5080-1-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove() return
void") .remove() is (again) the right callback to implement for platform
drivers.
Convert all PCI controller drivers to use .remove(), with the eventual goal
to drop struct platform_driver::remove_new(). As .remove() and .remove_new()
have the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Link: https://lore.kernel.org/r/20240923065706.728769-1-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[bhelgaas: add pcie-xilinx-nwl.c and tidy whitespace per Uwe Kleine-König:
https://lore.kernel.org/r/tdxrmmqyzcufupnwkdbg7lwgadizm7v3lxjirykijbml7x54ze@upbdzycdsilm]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Implement i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe Root Complex
(RC) support. While the controller resembles that of i.MX8MP, the PHY
differs significantly. Also, there's a distinction between PCI bus
addresses and CPU addresses.
Introduce IMX_PCIE_FLAG_CPU_ADDR_FIXUP in drvdata::flags to indicate driver
need the cpu_addr_fixup() callback to facilitate CPU address to PCI bus
address conversion according to "ranges" property.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-11-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: check resource_list_first_type() for NULL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Link: https://lore.kernel.org/r/20240827234848.4429-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Invoke the common PHY API to configure mode, speed, and submode. While
these functions are optional in the PHY interface, they are necessary for
certain PHY drivers. Lack of support for these functions in a PHY driver
does not cause harm.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-10-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Consolidated redundant if-checks pertaining to imx_pcie->phy. Instead of
two separate checks, merged them into one to improve code readability.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-8-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to assert/dassert the core
reset handled by this driver itself, let's introduce a new callback
core_reset() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to enable/disable the
reference clock handled by this driver itself, let's introduce a new
callback enable_ref_clk() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since this driver has evolved to support other i.MX SoCs such as
i.MX7/8/9, thus rename the 'imx6' prefix to 'imx' to avoid confusion.
The driver name is left unchanged to avoid breaking userspace.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log, refactor the IMX_* macros]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix missing call to phy_power_off() in the error path of
imx6_pcie_host_init(). Remove unnecessary check for imx6_pcie->phy
as the PHY API already handles NULL pointers.
Fixes: cbcf8722b5 ("phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.1+
Correct occasional MSI triggering failures in i.MX8MP PCIe EP by applying
the correct hardware outbound alignment requirement.
The i.MX platform has a restriction about outbound address translation. The
pci-epc-mem uses page_size to manage it. Set the correct page_size for i.MX
platform to meet the hardware requirement, which is the same as inbound
address alignment.
Thus, align it with epc_features::align.
Fixes: 1bd0d43dcf ("PCI: imx6: Clean up addr_space retrieval code")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-2-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Cc: <stable@vger.kernel.org> # 6.9+
Add IMX6_PCIE_FLAG_HAS_APP_RESET flag to IMX8MM_EP and IMX8MP_EP drvdata.
This flag was overlooked during code restructuring. It is crucial to
release the app-reset from the System Reset Controller before initiating
LTSSM to rectify the issue.
Fixes: 0c9651c21f ("PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-1-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9+
Within kirin_pcie_parse_port(), the pcie->num_slots is compared to
pcie->gpio_id_reset size (MAX_PCI_SLOTS) which is correct and would lead
to an overflow.
Thus, fix condition to pcie->num_slots + 1 >= MAX_PCI_SLOTS and move
pcie->num_slots increment below the if-statement to avoid out-of-bounds
array access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b22dbbb245 ("PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge")
Link: https://lore.kernel.org/linux-pci/20240903115823.30647-1-adiupina@astralinux.ru
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't populate the const read-only array check_addr on the stack at
run time, instead make it static.
Link: https://lore.kernel.org/linux-pci/20240822205941.643187-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
[kwilczynski: refactor array definition]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
Historically, Qcom PCIe RC controllers lacked standard hotplug support. So
when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. But this can be avoided by using the Link
up event exposed by the Qcom specific 'global_irq' interrupt.
Qcom PCIe RC controllers are capable of generating the 'global' SPI
interrupt to the host CPUs. The device driver can use this interrupt to
identify events such as PCIe link specific events, safety events etc...
One such event is the PCIe Link up event generated when an endpoint is
detected on the bus and the Link is 'up'. This event can be used to
enumerate the PCIe endpoint devices without user intervention.
So add support for capturing the PCIe Link up event using the 'global'
interrupt in the driver. Once the Link up event is received, the bus
underneath the host bridge is scanned to enumerate PCIe endpoint devices.
All of the Qcom SoCs have only one Root Port per controller instance. So
only a single 'Link up' event is generated for the PCIe controller.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-11-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Currently, the IRQ device name for both of these IRQs doesn't have Qcom
specific prefix and PCIe domain number. This causes 2 issues:
1. Pollutes the global IRQ namespace since 'global' is a common name.
2. When more than one EP controller instance is present in the SoC, naming
conflict will occur.
Hence, add 'qcom_pcie_ep_' prefix and PCIe domain number suffix to the IRQ
names to uniquely identify the IRQs and also to fix the above mentioned
issues.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-6-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Current error message just prints the contents of PARF_INT_ALL_STATUS
register as if like the IRQ event number. It could mislead the users.
Reword it to make it clear that the error message is actually showing the
interrupt status register to help debug spurious IRQ events.
While at it, let's also switch over to dev_WARN_ONCE() so that any IRQ
storm won't flood the kernel log buffer.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-2-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Once the events are disabled in PARF_INT_ALL_MASK register, only the
enabled events will generate global IRQ. So there is no need to do the
masking again in the IRQ handler, drop it.
If there are any spurious IRQs getting generated, they will be reported
using the existing dev_err() in the handler.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-1-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
With commit 5b6272e0ef ("PCI: qcom: Add OPP support to scale
performance"), OPP was used to control the interconnect and power domains
if the platform supported OPP. Also to maintain the backward compatibility
with platforms not supporting OPP but just ICC, the above mentioned commit
assumed that if ICC was not available on the platform, it would resort to
OPP.
Unfortunately, some old platforms don't support either ICC or OPP. On those
platforms, resorting to OPP in the absence of ICC throws below errors from
OPP core during suspend and resume:
qcom-pcie 1c08000.pcie: dev_pm_opp_set_opp: device opp doesn't exist
qcom-pcie 1c08000.pcie: _find_key: OPP table not found (-19)
Also, it doesn't make sense to invoke the OPP APIs when OPP is not
supported by the platform at all.
Add a "use_pm_opp" flag to identify whether OPP is supported and use it to
control invoking the OPP APIs.
Fixes: 5b6272e0ef ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240722131128.32470-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
SA8775P SoC has support for the hardware parity check feature on the MHI
RAM (entity that holds MHI registers, etc.) But due to a hardware bug in
the parity check logic, the data parity error interrupt is getting
generated all the time when using MHI. So the hardware team has suggested
disabling the parity check error to work around the hardware bug.
Mask the parity error interrupt in PARF_INT_ALL_5_MASK register.
Fixes: 58d0d3e032 ("PCI: qcom-ep: Add support for SA8775P SOC")
Link: https://lore.kernel.org/linux-pci/20240808063057.7394-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code accidentally uses && where || was intended. It potentially
results in a NULL dereference.
Thus, fix the if-statement expression to use the correct condition.
Fixes: 86f271f22b ("PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)")
Link: https://lore.kernel.org/linux-pci/1b762a93-e1b2-4af3-8c04-c8843905c279@stanley.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
- Remove unused struct 'acpi_handle_node' (Dr. David Alan Gilbert)
- Use array notation for portdrv .id_table consistently (Masahiro Yamada)
- Switch to new Intel CPU model defines (Tony Luck)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)
* pci/misc:
PCI: controller: Add missing MODULE_DESCRIPTION() macros
PCI: Add missing MODULE_DESCRIPTION() macros
PCI/PM: Switch to new Intel CPU model defines
PCI: Use array for .id_table consistently
ACPI: PCI: Remove unused struct 'acpi_handle_node'
- Ensure Tegra194 and Tegra234 inbound ATU entries are 64KB-aligned to
match the hardware restriction (Jon Hunter)
- Remove unused struct 'tegra_pcie_soc' (Dr. David Alan Gilbert)
* pci/controller/tegra194:
PCI: tegra: Remove unused struct 'tegra_pcie_soc'
PCI: tegra194: Set EP alignment restriction for inbound ATU
- Use dev_err_probe() in dw-rockchip probe error path so the failures
aren't silent (Uwe Kleine-König)
- Sleep PCIE_T_PVPERL_MS (100ms) before deasserting PERST# (Damien Le Moal)
- Sleep PCIE_T_RRS_READY_MS (100ms) after conventional reset, before a
config access (Damien Le Moal)
- Request the PERST# GPIO with GPIOD_OUT_LOW so it matches the POR value,
which avoids a spurious PERST# assertion and fixes a Qcom modem firmware
crash and issues with WLAN controllers, e.g., RTL8822CE (Manivannan
Sadhasivam for rockchip, Niklas Cassel for dw-rockchip)
- Refactor dw-rockchip and add support for Endpoint mode for rk3568 and
rk3588 (Niklas Cassel)
* pci/controller/rockchip:
PCI: dw-rockchip: Use pci_epc_init_notify() directly
PCI: dw-rockchip: Add endpoint mode support
PCI: dw-rockchip: Refactor the driver to prepare for EP mode
PCI: dw-rockchip: Add rockchip_pcie_get_ltssm() helper
PCI: dw-rockchip: Fix weird indentation
PCI: dw-rockchip: Fix initial PERST# GPIO value
PCI: dw-rockchip: Add error messages in .probe() error paths
PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
PCI: rockchip-host: Wait 100ms after reset before starting configuration
PCI: rockchip-host: Fix rockchip_pcie_host_init_port() PERST# handling
- Add Synopsys DWC macros for lane skew configuration (Yoshihiro Shimoda)
- Add struct rcar_gen4_pcie_drvdata to provide for future SoCs with
different initialization requirements (Yoshihiro Shimoda)
- Add .ltssm_control() method for SoC dependencies (Yoshihiro Shimoda)
- Add r8a779g0 (R-Car V4H) support (Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Add support for R-Car V4H
PCI: rcar-gen4: Add .ltssm_control() for other SoC support
PCI: rcar-gen4: Add struct rcar_gen4_pcie_drvdata
PCI: dwc: Add PCIE_PORT_{FORCE,LANE_SKEW} macros
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
- Enable BAR 0 only for v3.65a to avoid Completion Timeouts that
cause a 45 second boot delay on the v4.90a-based AM654x SoC (Siddharth
Vadapalli)
- Avoid a NULL pointer dereference if DT failed to provide a host bridge
memory window (Aleksandr Mishin)
* pci/controller/keystone:
PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
PCI: keystone: Fix NULL pointer dereference in case of DT error in ks_pcie_setup_rc_app_regs()
PCI: keystone: Don't enable BAR 0 for AM654x
PCI: keystone: Relocate ks_pcie_set/clear_dbi_mode()
- Correct the dra7xx_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/dra7xx:
PCI: dra7xx: Fix dra7xx_pcie_cpu_addr_fixup() parameter name
- Correct the artpec6_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/artpec6:
PCI: artpec6: Fix artpec6_pcie_cpu_addr_fixup() parameter name
- Check IORESOURCE_BUS existence to avoid NULL pointer dereference
(Aleksandr Mishin)
* pci/controller/al:
PCI: al: Check IORESOURCE_BUS existence during probe
- Use msleep() in DWC core instead of usleep_range() for ~100 ms sleep
(Konrad Dybcio)
- Fix iATU slot management to avoid using the wrong slot after PERST#
assert/deassert, which could potentially cause DMA to go the wrong place
(Frank Li)
- Consolidate dw_pcie_prog_outbound_atu() arguments into a struct to ease
adding new functionality like initiating Message TLPs (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe messages (Yoshihiro Shimoda)
- Add #defines for PCIe INTx messages (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe PME_Turn_Off messages for
system suspend (Frank Li)
- Add dw_pcie_ep_linkdown() to reinitialize registers that are lost when
the link goes down (Manivannan Sadhasivam)
- Use dw_pcie_ep_linkdown() to reinitialize qcom non-sticky registers that
are lost when the link goes down (Manivannan Sadhasivam)
- Enforce DWC limitation that 64-bit BARs must start with the even numbered
BAR (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Enforce DWC specific 64-bit BAR limitation
PCI: layerscape-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper
PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system suspend
PCI: Add PCIE_MSG_CODE_PME_TURN_OFF message macro
PCI: Add PCIE_MSG_CODE_ASSERT_INTx message macros
PCI: dwc: Add outbound MSG TLPs support
PCI: dwc: Consolidate args of dw_pcie_prog_outbound_atu() into a structure
PCI: dwc: Fix index 0 incorrectly being interpreted as a free ATU slot
PCI: dwc: Use msleep() in dw_pcie_wait_for_link()
- Include <linux/irqchip/chained_irq.h> in dra7xx to avoid implicitly
including it elsewhere (Andy Shevchenko)
- Remove unused <linux/of_gpio.h> from aardvark and dwc drivers (dra7xx,
meson, qcom, tegra194) (Andy Shevchenko)
- Convert kirin to use scoped for_each_available_child_of_node() to ease
future error exits (Javier Carrasco)
- Convert imx6 and kirin to use the agnostic GPIO API to simplify GPIO
setup and remove usage of the deprecated of_gpio.h API (Andy Shevchenko)
* pci/controller/gpio:
PCI: kirin: Convert to use agnostic GPIO API
PCI: kirin: Convert kirin_pcie_parse_port() to scoped iterator
PCI: imx6: Convert to use agnostic GPIO API
PCI: dwc: Remove unused of_gpio.h inclusion
PCI: aardvark: Remove unused of_gpio.h inclusion
PCI: dra7xx: Add missing chained IRQ header inclusion
Smatch complains that "ret" could be uninitialized if "pcie->icc_mem" is
NULL and "pm_suspend_target_state == PM_SUSPEND_MEM".
Silence this warning by initializing ret to zero.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-4-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Only call dev_pm_opp_put() if dev_pm_opp_find_freq_exact() succeeds;
otherwise it leads to an error pointer dereference.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-3-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A previous commit ("PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper")
removed the dw_pcie_ep_init_notify() wrapper and changed the DWC glue
drivers to instead use pci_epc_init_notify() directly.
The endpoint support for the dw-rockchip had not been merged at that point
in time, so the previous commit wrapper") did not update dw-rockchip.
Do the same change for dw-rockchip, so that the driver will not try
to use a function that has now been removed.
Link: https://lore.kernel.org/linux-pci/20240622132024.2927799-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the driver to prepare for EP mode.
Add of-match data to the existing compatible, and explicitly define it as
DW_PCIE_RC_TYPE. This way, we will be able to add EP mode in a follow-up
commit in a much less intrusive way, which makes the follow-up commit much
easier to review.
No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-9-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a rockchip_pcie_ltssm() helper function that reads the LTSSM status.
This helper will be used in additional places in follow-up commits.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-8-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix the indentation of rockchip_pcie_{readl,writel}_apb() parameters to
match the opening parenthesis.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-7-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Drivers that silently fail to probe provide a bad user experience and
make it unnecessarily hard to debug such a failure.
Fix it by using dev_err_probe() instead of a plain return.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240227141256.413055-2-ukleinek@debian.org
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/20240609-pcie-kirin-memleak-v1-1-62b45b879576@gmail.com
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
maintains hardware state of a regulator by performing max aggregation of
the requests made by all of the clients.
PCIe controller can operate on different RPMh performance state of power
domain based on the speed of the link. And this performance state varies
from target to target, like some controllers support GEN3 in NOM (Nominal)
voltage corner, while some other supports GEN3 in low SVS (static voltage
scaling).
The SoC can be more power efficient if we scale the performance state
based on the aggregate PCIe link bandwidth.
Add Operating Performance Points (OPP) support to vote for RPMh state based
on the aggregate link bandwidth.
OPP can handle ICC bw voting also, so move ICC bw voting through OPP
framework if OPP entries are present.
As we are moving ICC voting as part of OPP, don't initialize ICC if OPP
is supported.
Before PCIe link is initialized vote for highest OPP in the OPP table,
so that we are voting for maximum voltage corner for the link to come up
in maximum supported speed.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-4-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To access the host controller registers of the host controller and the
endpoint BAR/config space, the CPU-PCIe ICC (interconnect) path should
be voted otherwise it may lead to NoC (Network on chip) timeout.
We are surviving because of other driver voting for this path.
As there is less access on this path compared to PCIe to mem path
add minimum vote i.e 1KBps bandwidth always which is sufficient enough
to keep the path active and is recommended by HW team.
During S2RAM (Suspend-to-RAM), the DBI access can happen very late (while
disabling the boot CPU). So do not disable the CPU-PCIe interconnect path
during S2RAM as that may lead to NoC error.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-1-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Add support for r8a779g0 (R-Car V4H).
This driver previously supported r8a779f0 (R-Car S4-8). PCIe features
of both r8a779f0 and r8a779g0 are almost all the same. For example:
- PCI Express Base Specification Revision 4.0
- Root complex mode and endpoint mode are supported
However, r8a779g0 requires specific firmware to be provided, to
initialize the PHY. Otherwise, the PCIe controller will not work.
[kwilczynski: drop the proprietary firmware conversion comment]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Sequence for controlling the LTSSM state machine is going to change
for SoCs like r8a779f0. Move the LTSSM code to a new callback
ltssm_control() and populate it for each SoCs.
This also warrants the addition of new compatibles for r8a779g0 and
r8a779h0. But since they are already part of the DT binding, it won't
make any difference.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to support future SoCs such as r8a779g0 (R-Car V4H) and
r8a779h0 (R-Car V4M) that require different initialization settings,
introduce SoC specific driver data with the initial member being the
device mode.
No functional change.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
R-Car Gen4 PCIe controller needs to use the Synopsys-specific PCIe
configuration registers. So, add the macros.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
'tegra_pcie_soc' has been unused since 56e15a238d ("PCI: tegra: Add
Tegra194 PCIe support"). Remove it.
Link: https://lore.kernel.org/r/20240527160118.37069-1-linux@treblig.org
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Tegra194 and Tegra234 PCIe EP controllers have 64K alignment restriction
for the inbound ATU. Set the endpoint inbound ATU alignment to 64kB in the
Tegra194 PCIe driver.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Link: https://lore.kernel.org/linux-pci/20240508092207.337063-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to hardcode the clock info in the driver as driver can
rely on the devicetree to supply the clocks required for the functioning
of the peripheral.
Thus, remove the static clock info and obtain the platform supplied
clocks. All the clocks supplied are obtained and enabled using the
devm_clk_bulk_get_all_enable() API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240220084046.23786-3-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the dra7xx_pcie_cpu_addr_fixup() function parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-3-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the artpec6_pcie_cpu_addr_fixup() parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-4-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
SA8775P SoC supports the new Hyper DMA (HDMA) DMA Engine inside the DWC IP,
so add support for it by passing the mapping format and the number of
read/write channels count.
The PCIe EP controller used on this SoC is of version 1.34.0, so a separate
config struct is introduced for the sake of enabling HDMA conditionally.
It should be noted that for the eDMA support (predecessor of HDMA), there
are no mapping format and channels count specified. That is because eDMA
supports auto detection of both parameters, whereas HDMA doesn't.
[mani: reworded commit message, added kdoc, and minor cleanups]
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-4-f04c5cdde760@linaro.org
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Instead of maintaining a separate capability for glue drivers that cannot
support auto detection of the eDMA mapping format, pass the mapping format
directly from them.
This will simplify the code and also allow adding HDMA support that also
doesn't support auto detection of mapping format.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-3-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In the case of Hyper DMA (HDMA) present in DWC controllers, there is no way
the drivers can auto detect the number of read/write channels as like its
predecessor embedded DMA (eDMA). So the glue drivers making use of HDMA
have to pass the channels count during probe.
To accommodate that, skip the existing auto detection of channels count
procedure for HDMA based platforms. If the channels count passed by the
glue drivers were wrong in any form, then the existing sanity check will
catch it.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-2-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In order to add support for Hyper DMA (HDMA), refactor the existing
dw_pcie_edma_find_chip() API by moving the common code to separate
functions.
No functional change.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-1-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add support for SA8775P SoC to the Qualcomm PCIe Endpoint Controller
driver. Adding new compatible string as it has different set of clocks
compared to other SoCs.
Link: https://lore.kernel.org/linux-pci/1714492540-15419-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need for the device drivers to validate the clocks defined in
Devicetree. The validation should be performed by the DT schema and the
drivers should just get all the clocks from DT. Right now the driver
hardcodes the clock info and validates them against DT which is redundant.
So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
and get rid of all static clocks info from the driver. This simplifies the
driver.
Link: https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Return success from endpoint probe before incorrectly dropping the
reference to the BPMP (Vidya Sagar)
* pci/controller/tegra194:
PCI: tegra194: Fix probe path for Endpoint mode
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
"core_init_notifier" flag is set by the glue drivers requiring refclk from
the host to complete the DWC core initialization. Also, those drivers will
send a notification to the EPF drivers once the initialization is fully
completed using the pci_epc_init_notify() API. Only then, the EPF drivers
will start functioning.
For the rest of the drivers generating refclk locally, EPF drivers will
start functioning post binding with them. EPF drivers rely on the
'core_init_notifier' flag to differentiate between the drivers.
Unfortunately, this creates two different flows for the EPF drivers.
So to avoid that, let's get rid of the "core_init_notifier" flag and follow
a single initialization flow for the EPF drivers. This is done by calling
the dw_pcie_ep_init_notify() from all glue drivers after the completion of
dw_pcie_ep_init_registers() API. This will allow all the glue drivers to
send the notification to the EPF drivers once the initialization is fully
completed.
Only difference here is that, the drivers requiring refclk from host will
send the notification once refclk is received, while others will send it
during probe time itself.
But this also requires the EPC core driver to deliver the notification
after EPF driver bind. Because, the glue driver can send the notification
before the EPF drivers bind() and in those cases the EPF drivers will miss
the event. To accommodate this, EPC core is now caching the state of the
EPC initialization in 'init_complete' flag and pci-ep-cfs driver sends the
notification to EPF drivers based on that after each EPF driver bind.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-8-082625472414@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently, dw_pcie_ep_init_registers() API is directly called by the glue
drivers requiring active refclk from host. But for the other drivers, it is
getting called implicitly by dw_pcie_ep_init(). This is due to the fact
that this API initializes DWC EP specific registers and that requires an
active refclk (either from host or generated locally by endpoint itsef).
But, this causes a discrepancy among the glue drivers. So to avoid this
confusion, let's call this API directly from all glue drivers irrespective
of refclk dependency. Only difference here is that the drivers requiring
refclk from host will call this API only after the refclk is received and
other drivers without refclk dependency will call this API right after
dw_pcie_ep_init().
With this change, the check for 'core_init_notifier' flag can now be
dropped from dw_pcie_ep_init() API. This will also allow us to remove the
'core_init_notifier' flag completely in the later commits.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-7-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
The goal of the dw_pcie_ep_init_complete() API is to initialize the DWC
specific registers post registering the controller with the EP framework.
But the naming doesn't reflect its functionality and causes confusion. So,
let's rename it to dw_pcie_ep_init_registers() to make it clear that it
initializes the DWC specific registers.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-6-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
For DWC glue drivers supporting PERST# (currently Qcom and Tegra194), some
of the DWC resources like eDMA should be cleaned up during the PERST#
assert time.
So let's introduce a dw_pcie_ep_cleanup() API that could be called by these
drivers to cleanup the DWC specific resources. Currently, it just removes
eDMA.
Closes: https://lore.kernel.org/linux-pci/ZWYmX8Y%2F7Q9WMxES@x1-carbon
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-5-082625472414@linaro.org
Reported-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
dw_pcie_ep_exit() API is undoing what the dw_pcie_ep_init() API has done
already (at least partly). But the API name dw_pcie_ep_exit() is not quite
reflecting that. So let's rename it to dw_pcie_ep_deinit() to make the
purpose of this API clear. This also aligns with the DWC host driver.
Link: https://patchwork.kernel.org/project/linux-pci/patch/20240327-pci-dbi-rework-v12-4-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
deinit() callback was solely introduced for the pcie-rcar-gen4 driver where
it is used to do platform specific resource deallocation. And this callback
is called right at the end of the dw_pcie_ep_exit() API. So it doesn't
matter whether it is called within or outside of dw_pcie_ep_exit() API.
So let's remove this callback and directly call rcar_gen4_pcie_ep_deinit()
in pcie-rcar-gen4 driver to do resource deallocation after the completion
of dw_pcie_ep_exit() API in rcar_gen4_remove_dw_pcie_ep().
This simplifies the DWC layer.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-3-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
All of the APIs are missing the Kernel-doc comments. Hence, add them.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-2-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
The DWC glue drivers requiring an active reference clock from the PCIe host
for initializing their PCIe EP core, set a flag called 'core_init_notifier'
to let DWC driver know that these drivers need a special attention during
initialization. In these drivers, access to the hw registers (like DBI)
before receiving the active refclk from host will result in access failure
and also could cause a whole system hang.
But the current DWC EP driver doesn't honor the requirements of the drivers
setting 'core_init_notifier' flag and tries to access the DBI registers
during dw_pcie_ep_init(). This causes the system hang for glue drivers such
as Tegra194 and Qcom EP as they depend on refclk from host and have set the
above mentioned flag.
To workaround this issue, users of the affected platforms have to maintain
the dependency with the PCIe host by booting the PCIe EP after host boot.
But this won't provide a good user experience, since PCIe EP is _one_ of
the features of those platforms and it doesn't make sense to delay the
whole platform booting due to PCIe requiring active refclk.
So to fix this issue, let's move all the DBI access from
dw_pcie_ep_init() in the DWC EP driver to the dw_pcie_ep_init_complete()
API. This API will only be called by the drivers setting
'core_init_notifier' flag once refclk is received from host. For the rest
of the drivers that gets the refclk locally, this API will be called
within dw_pcie_ep_init().
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-1-082625472414@linaro.org
Fixes: e966f7390d ("PCI: dwc: Refactor core initialization code for EP mode")
Co-developed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AP3I
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate interrupt related code in irq.c (Ilpo Järvinen)
- Reduce kernel size by replacing sysfs resource macros with
functions (Ilpo Järvinen)
- Reduce kernel size by compiling sysfs support only when
CONFIG_SYSFS=y (Lukas Wunner)
- Avoid using Extended Tags on 3ware-9650SE Root Port to work around
an apparent hardware defect (Jörg Wedekind)
Resource management:
- Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner)
- Move pci_iomap.c and other PCI-specific devres code to drivers/pci
(Philipp Stanner)
- Consolidate PCI devres code in devres.c (Philipp Stanner)
Power management:
- Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't
know how to return correctly to D0, and remove previous quirk that
wasn't as specific (Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any
runtime PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races
between .remove() and .runtime_idle(), which caused intermittent
page faults when the rtsx .runtime_idle() accessed registers that
its .remove() had already unmapped (Rafael J. Wysocki)
Virtualization:
- Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs
with VFIO, e.g., for professional audio software on many Apple
machines, at the cost of leaking state between VMs (Edmund Raile)
Error handling:
- Print all logged TLP Prefixes, not just the first, after AER or DPC
errors (Ilpo Järvinen)
- Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which
still don't advertise a legal size (Paul Menzel)
- Ignore expected DPC Surprise Down errors on hot removal (Smita
Koralahalli)
- Block runtime suspend while handling AER errors to avoid races that
prevent the device form being resumed from D3hot (Stanislaw
Gruszka)
Peer-to-peer DMA:
- Use atomic XA allocation in RCU read section (Christophe JAILLET)
ASPM:
- Collect bits of ASPM-related code that we need even without
CONFIG_PCIEASPM into aspm.c (David E. Box)
- Save/restore L1 PM Substates config for suspend/resume (David E.
Box)
- Update save_save when ASPM config is changed, so a .slot_reset()
during error recovery restores the changed config, not the
.probe()-time config (Vidya Sagar)
Endpoint framework:
- Refactor and improve pci_epf_alloc_space() API (Niklas Cassel)
- Clean up endpoint BAR descriptions (Niklas Cassel)
- Fix ntb_register_device() name leak in error path (Yang Yingliang)
- Return actual error code for pci_vntb_probe() failure (Yang
Yingliang)
Broadcom STB PCIe controller driver:
- Fix MDIO write polling, which previously never waited for
completion (Jonathan Bell)
Cadence PCIe endpoint driver:
- Clear the ARI "Next Function Number" of last function (Jasko-EXT
Wojciech)
Freescale i.MX6 PCIe controller driver:
- Simplify by replacing switch statements with function pointers for
different hardware variants (Frank Li)
- Simplify by using clk_bulk*() API (Frank Li)
- Remove redundant DT clock and reg/reg-name details (Frank Li)
- Add i.MX95 DT and driver support for both Root Complex and Endpoint
mode (Frank Li)
Microsoft Hyper-V host bridge driver:
- Reduce memory usage by limiting ring buffer size to 16KB instead of
4 pages (Michael Kelley)
Qualcomm PCIe controller driver:
- Add X1E80100 DT and driver support (Abel Vesa)
- Add DT 'required-opps' for SoCs that require a minimum performance
level (Johan Hovold)
- Make DT 'msi-map-mask' optional, depending on how MSI interrupts
are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY
configuration isn't tuned correctly for L0s (Johan Hovold)
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and
separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150,
SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof
Kozlowski)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay
Sarkar)
Synopsys DesignWare PCIe controller driver:
- Allocate 64-bit MSI address if no 32-bit address is available (Ajay
Agarwal)
- Fix endpoint Resizable BAR to actually advertise the required 1MB
size (Niklas Cassel)
MicroSemi Switchtec management driver:
- Release resources if the .probe() fails (Christophe JAILLET)
Miscellaneous:
- Make pcie_port_bus_type const (Ricardo B. Marliere)"
* tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits)
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI: hv: Fix ring buffer size calculation
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
PCI: dwc: Strengthen the MSI address allocation logic
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
PCI/AER: Block runtime suspend when handling errors
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
...
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate
files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350,
SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski)
- Allow 'required-opps' DT property for SoCs that require a minimum
performance level for the power domain (Johan Hovold)
- Remove requirement for 'msi-map-mask' DT property since it depends on how
MSIs are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because their PHY
configuration isn't tuned for L0s, which results in many Correctable
Errors (Johan Hovold)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add DT binding and driver support for X1E80100 (Abel Vesa)
* pci/controller/qcom:
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
dt-bindings: PCI: qcom,pcie-sa8775p: Move SA8775p to dedicated schema
dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8180x: Move SC8180X to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8280xp: Move SC8280XP to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8350: Move SM8350 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8150: Move SM8150 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8250: Move SM8250 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8450: Move SM8450 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8550: Move SM8550 to dedicated schema
- Fall back to allocating 64-bit MSI DMA address if unable to allocate a
32-bit address (Ajay Agarwal)
* pci/controller/dwc:
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: dwc: Strengthen the MSI address allocation logic
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
There can be platforms that do not use/have 32-bit DMA addresses.
The current implementation of 32-bit IOVA allocation can fail for
such platforms, eventually leading to the probe failure.
Try to allocate a 32-bit msi_data. If this allocation fails,
attempt a 64-bit address allocation. Please note that if the
64-bit MSI address is allocated, then the EPs supporting 32-bit
MSI address only will not work.
Link: https://lore.kernel.org/linux-pci/20240221153840.1789979-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Will McVicker <willmcvicker@google.com>
Add the compatible and the driver data for X1E80100 PCIe controller.
There are 5 controller instances found on this platform, out of which
2 are Gen3 with speeds of up to 8.0GT/s, while the other 3 are Gen4 with
speeds of up to 16GT/s.
The version of the controller is 1.38.0 for all instances, but they are
compatible with 1.9.0 config. The max link width is x8 for one
controller, x4 for two of others and x2 for the two left.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240301-x1e80100-pci-v4-2-7ab7e281d647@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Commit 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting
1.9.0 ops") started enabling ASPM unconditionally when the hardware
claims to support it. This triggers Correctable Errors for some PCIe
devices on machines like the Lenovo ThinkPad X13s when L0s is enabled,
which could indicate an incomplete driver ASPM implementation or that
the hardware does in fact not support L0s.
This has now been confirmed by Qualcomm to be the case for sc8280xp and
its derivate platforms (e.g. sa8540p and sa8295p). Specifically, the PHY
configuration used on these platforms is not correctly tuned for L0s and
there is currently no updated configuration available.
Add a new flag to the driver configuration data and use it to disable
ASPM L0s on sc8280xp, sa8540p and sa8295p for now.
Note that only the 1.9.0 ops enable ASPM currently.
Link: https://lore.kernel.org/r/20240306095651.4551-4-johan+linaro@kernel.org
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 6.7
Add iMX95 EP support and add 64bit address support.
The internal bus bridge for PCI support 64bit DMA address in iMX95 hence
call dma_set_mask_and_coherent() to set 64 bit DMA mask.
Link: https://lore.kernel.org/r/20240220161924.3871774-15-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The i.MX EP exhibits variations in epc_features among different EP
configurations. This introduces the addition of epc_features in
imx6_pcie_drvdata to accommodate these differences. It's important to note
that there are no functional changes in this commit; instead, it lays the
groundwork for supporting i.MX95 EP functions.
Link: https://lore.kernel.org/r/20240220161924.3871774-13-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the dw_pcie_ep_init() function is already fetching the 'addr_space'
region, no need to do the same in this driver.
Link: https://lore.kernel.org/r/20240220161924.3871774-12-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to initialize the PHY handled by
this driver itself, let's introduce a new callback init_phy() and define it
for platforms that require it.
Link: https://lore.kernel.org/r/20240220161924.3871774-7-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::mode_off and drvdata::mode_mask to simplify
imx6_pcie_configure_type() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-6-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::ltssm_off and drvdata::ltssm_mask to simplify
imx6_pcie_ltssm_enable(disable)() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the reset handling logic in the imx6 PCI driver by adding
IMX6_PCIE_FLAG_HAS_*_RESET bitmask define for drvdata::flags.
The drvdata::flags and bitmask ensure a cleaner and more scalable
switch-case structure for handling reset.
Link: https://lore.kernel.org/r/20240220161924.3871774-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Since some i.MX platforms make use of a separate PHY driver, use
IMX6_PCIE_FLAG_HAS_PHYDRV flag to identify them and get the reference to
PHY from DT to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the clock handling logic. Add 'clk_names' define in drvdata.
Use clk_bulk*() API to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The definition of a reserved BAR is that EPF drivers should not touch
them.
The definition of only_64bit is that the EPF driver must configure this
BAR as 64-bit. (An EPF driver is not allowed to choose if this BAR should
be configured as 32-bit or 64-bit.)
Thus, it does not make sense to put only_64bit of a BAR that EPF drivers
are not allow to touch.
Drop the only_64bit property from hardware descriptions that are of type
reserved BAR.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-3-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The hardware description for BARs is scattered in many different variables
in pci_epc_features. Some of these things are mutually exclusive, so it
can create confusion over which variable that has precedence over another.
Improve the situation by creating a struct pci_epc_bar_desc, and a new
enum pci_epc_bar_type, and convert the endpoint controller drivers to use
this more well defined format.
Additionally, some endpoint controller drivers mark the BAR succeeding a
"64-bit only BAR" as reserved, while some do not. By definition, a 64-bit
BAR uses the succeeding BAR for the upper 32-bits, so an EPF driver cannot
use a BAR succeeding a 64-bit BAR. Ensure that all endpoint controller
drivers are uniform, and actually describe a reserved BAR as reserved.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=jJks
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Fix an unintentional truncation of DWC MSI-X address to 32 bits and
update similar MSI code to match (Dan Carpenter)
* tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: dwc: Clean up dw_pcie_ep_raise_msi_irq() alignment
PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
I recently changed the alignment code in dw_pcie_ep_raise_msix_irq(). The
code in dw_pcie_ep_raise_msi_irq() is similar, so update it to match, just
for consistency. (No effect on runtime, just a cleanup).
Link: https://lore.kernel.org/r/184097e0-c728-42c7-9e8a-556bd33fb612@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd6 ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
A last minute revert in 6.7-final introduced a potential deadlock when
enabling ASPM during probe of Qualcomm PCIe controllers as reported by
lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0 #40 Not tainted
--------------------------------------------
kworker/u16:5/90 is trying to acquire lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc
but task is already holding lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Call trace:
print_deadlock_bug+0x25c/0x348
__lock_acquire+0x10a4/0x2064
lock_acquire+0x1e8/0x318
down_read+0x60/0x184
pcie_aspm_pm_state_change+0x58/0xdc
pci_set_full_power_state+0xa8/0x114
pci_set_power_state+0xc4/0x120
qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom]
pci_walk_bus+0x64/0xbc
qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom]
The deadlock can easily be reproduced on machines like the Lenovo ThinkPad
X13s by adding a delay to increase the race window during asynchronous
probe where another thread can take a write lock.
Add a new pci_set_power_state_locked() and associated helper functions that
can be called with the PCI bus semaphore held to avoid taking the read lock
twice.
Link: https://lore.kernel.org/r/ZZu0qx2cmn7IwTyQ@hovoldconsulting.com
Link: https://lore.kernel.org/r/20240130100243.11011-1-johan+linaro@kernel.org
Fixes: f93e71aea6 ("Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org> # 6.7
-----BEGIN PGP SIGNATURE-----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=ri0M
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Reserve ECAM so we don't assign it to PCI BARs; this works around
bugs where BIOS included ECAM in a PNP0A03 host bridge window,
didn't reserve it via a PNP0C02 motherboard device, and didn't
allocate space for SR-IOV VF BARs (Bjorn Helgaas)
- Add MMCONFIG/ECAM debug logging (Bjorn Helgaas)
- Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas)
- Log device type (Root Port, Switch Port, etc) during enumeration
(Bjorn Helgaas)
- Log bridges before downstream devices so the dmesg order is more
logical (Bjorn Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc)
consistently instead of a mix of names and "reg 0x10" (Puranjay
Mohan, Bjorn Helgaas)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding
rather than the 8b/10b or 128b/130b used by lower rates (Ilpo
Järvinen)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI
lpfc (Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
Resource management:
- Restructure pci_dev_for_each_resource() to avoid computing the
address of an out-of-bounds array element (the bounds check was
performed later so the element was never actually *read*, but it's
nicer to avoid even computing an out-of-bounds address) (Andy
Shevchenko)
Driver binding:
- Convert pci-host-common.c platform .remove() callback to
.remove_new() returning 'void' since it's not useful to return
error codes here (Uwe Kleine-König)
- Convert exynos, keystone, kirin from .remove() to .remove_new(),
which returns void instead of int (Uwe Kleine-König)
- Drop unused struct pci_driver.node member (Mathias Krause)
Virtualization:
- Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc)
Error handling:
- Log AER errors as "Correctable" (not "Corrected") or
"Uncorrectable" to match spec terminology (Bjorn Helgaas)
- Decode Requester ID when no error info found instead of printing
the raw hex value (Bjorn Helgaas)
Endpoint framework:
- Use a unique test pattern for each BAR in the pci_endpoint_test to
make it easier to debug address translation issues (Niklas Cassel)
Broadcom STB PCIe controller driver:
- Add DT property "brcm,clkreq-mode" and driver support for different
CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan)
Freescale Layerscape PCIe controller driver:
- Add suspend/resume support for Layerscape LS1043a and LS1021a,
including software-managed PME_Turn_Off and transitions between L0,
L2/L3_Ready Link states (Frank Li)
MediaTek PCIe controller driver:
- Clear MSI interrupt status before handler to avoid missing MSIs
that occur after the handler (qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 translation window setup to handle MMIO space
that is not a power of two in size (Jianjun Wang)
Qualcomm PCIe controller driver:
- Increase qcom iommu-map maxItems to accommodate SDX55 (five
entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly
called "reset-names" (Krzysztof Kozlowski)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil
Armstrong)
Renesas R-Car PCIe controller driver:
- Replace of_device.h with explicit of.h include to untangle header
usage (Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v
regulators on KingFisher (Wolfram Sang)
SiFive FU740 PCIe controller driver:
- Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to
ARCH_SIFIVE (Conor Dooley)
Synopsys DesignWare PCIe controller driver:
- Align iATU mapping for endpoint MSI-X (Niklas Cassel)
- Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro
Shimoda)
- Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro
Shimoda)
- Rename struct dw_pcie_ep_ops.func_conf_select() to
.get_dbi_offset() to be more descriptive (Yoshihiro Shimoda)
- Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro
Shimoda)
TI J721E PCIe driver:
- Add j721e DT and driver support for 'num-lanes' for devices that
support x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt
Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is
specific to those TI SoC parts (Peter Robinson)
TI Keystone PCIe controller driver:
- Hold power management references to all PHYs while enabling them to
avoid a race when one provides clocks to others (Siddharth
Vadapalli)
Xilinx XDMA PCIe controller driver:
- Remove redundant dev_err(), since platform_get_irq() and
platform_get_irq_byname() already log errors (Yang Li)
- Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
(Krzysztof Wilczyński)
- Fix xilinx_pl_dma_pcie_init_irq_domain() error return when
irq_domain_add_linear() fails (Harshit Mogalapalli)
MicroSemi Switchtec management driver:
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was
done in stdev_release(), which used stale pointers if stdev->cdev
happened to be open when the PCI device was removed (Daniel
Stodden)
Miscellaneous:
- Convert interrupt terminology from "legacy" to "INTx" to be more
specific and match spec terminology (Damien Le Moal)
- In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of
deprecated ida_simple_*() API with ida_alloc() and ida_free()
(Christophe JAILLET)"
* tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Fix kernel-doc issues
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
PCI: keystone: Fix race condition when initializing PHYs
PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain()
PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error
PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning
PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers
PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops
PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops
PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members
misc: pci_endpoint_test: Use a unique test pattern for each BAR
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI/AER: Use explicit register sizes for struct members
PCI/AER: Decode Requester ID when no error info found
PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors
...
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more explicit and match spec
terminology (Bjorn Helgaas)
- Use existing PCI_IRQ_INTX, PCI_IRQ_MSI, PCI_IRQ_MSIX in artpec6, cadence,
designware, designware-plat, dra7xx, imx6, keembay, keystone, layerscape,
mhi, ntb, qcom, rcar, rcar-gen4, rockchip, tegra194, uniphier, vntb; drop
the redundant pci_epc_irq_type enum with the same values (Damien Le Moal)
- Use "intx" instead of "leg" or "legacy" when describing INTx interrupts
in endpoint core, endpoint tests, cadence, dra7xx, designware,
dw-rockchip, dwc core, imx6, keystone, layerscape, qcom, rcar-gen4,
rockchip, tegra194, uniphier, xilinx-nwl (Damien Le Moal)
* pci/irq-clean-up:
PCI: xilinx-nwl: Use INTX instead of legacy
PCI: rockchip-host: Rename rockchip_pcie_legacy_int_handler()
PCI: rockchip-ep: Use INTX instead of legacy
PCI: uniphier: Use INTX instead of legacy
PCI: tegra194: Use INTX instead of legacy
PCI: dw-rockchip: Rename rockchip_pcie_legacy_int_handler()
PCI: keystone: Use INTX instead of legacy
PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq()
PCI: cadence: Use INTX instead of legacy
PCI: dra7xx: Rename dra7xx_pcie_raise_legacy_irq()
misc: pci_endpoint_test: Use INTX instead of LEGACY
PCI: endpoint: Rename LEGACY to INTX in test function driver
PCI: endpoint: Use INTX instead of legacy
PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitions
PCI: Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX
- Replace of_device.h with explicit of.h include to untangle header usage
(Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators
on KingFisher (Wolfram Sang)
* pci/controller/rcar:
PCI: rcar-host: Add support for optional regulators
dt-bindings: PCI: rcar-pci-host: Add optional regulators
PCI: rcar-gen4: Replace of_device.h with explicit of.h include
- Add suspend/resume support for Layerscape LS1043a, including
software-managed PME_Turn_Off and transitions between L0, L2/L3_Ready
Link states (Frank Li)
* pci/controller/layerscape:
PCI: layerscape: Add suspend/resume for ls1043a
PCI: layerscape(ep): Rename pf_* as pf_lut_*
PCI: layerscape: Add suspend/resume for ls1021a
PCI: layerscape: Add function pointer for exit_from_l2()
- Use devm_kasprintf() to dynamically allocate clock names, removing need
for an intermediate buffer (Christophe JAILLET)
* pci/controller/kirin:
PCI: kirin: Use devm_kasprintf() to dynamically allocate clock names
- Hold power management references to all PHYs while enabling them to avoid
a race when one provides clocks to others (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Fix race condition when initializing PHYs
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
When building with clang 18 with the -Werror compiler option enabled,
the following error will be reported:
drivers/pci/controller/dwc/pcie-rcar-gen4.c:439:15: error: cast to smaller integer type 'enum dw_pcie_device_mode' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
439 | rcar->mode = (enum dw_pcie_device_mode)of_device_get_match_data(&rcar->pdev->dev);
To fix this issue, cast the data the of_device_get_match_data() helper
returns to uintptr_t rather than the dw_pcie_device_mode enum.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The current code calculated some dbi[2] registers' offset by calling
dw_pcie_ep_get_dbi[2]_offset() in each function. To improve the code
readability, add dw_pcie_ep_{read,write}_dbi[2} and some data-width
related helpers.
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the struct member .func_conf_select makes the intentions behind it
difficult to ascertain from its name alone, rename it to .get_dbi_offset
to make the intended usage more obvious.
[kwilczynski: commmit log]
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Since the name of the dw_pcie_ep_ops struct makes it obvious that it's
for the PCIe Endpoint, rename the struct member .ep_init to .init.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Since the name of the dw_pcie_host_ops struct makes it obvious that it's
for the PCIe Host, drop the host prefix from the struct members.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Lei Chuanhua <lchuanhua@maxlinear.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
In the Designware uniphier controller driver, including the endpoint
driver, change all names using "legacy" to use "intx", to match the
term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Designware tegra194 controller driver, change all names using
"legacy" to use "intx", to match the term used in the PCI
specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function rockchip_pcie_legacy_int_handler() to
rockchip_pcie_intx_handler() to match the code managing INTX interrupts
(e.g. intx_domain_ops) and the term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the Keystone controller driver, change all names using "legacy" to
use "intx" instead, to match the term used in the PCI specifications.
Given that the field legacy_intc_np of struct keystone_pcie is unused,
this field is removed instead of being renamed.
Link: https://lore.kernel.org/r/20231122060406.14695-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dw_pcie_ep_raise_legacy_irq() of the Designware
endpoint controller driver to dw_pcie_ep_raise_intx_irq() to match the
name of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename the function dra7xx_pcie_raise_legacy_irq() to
dra7xx_pcie_raise_intx_irq() to match the use of the PCI_IRQ_INTX macro.
Link: https://lore.kernel.org/r/20231122060406.14695-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
linux/pci.h defines the IRQ flags PCI_IRQ_INTX, PCI_IRQ_MSI and
PCI_IRQ_MSIX. Let's use these flags directly instead of the endpoint
definitions provided by enum pci_epc_irq_type. This removes the need
for defining this enum type completely.
Link: https://lore.kernel.org/r/20231122060406.14695-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Use devm_kasprintf() instead of open coding it. This saves the need of
an intermediate buffer.
There was also no reason to use devm_kstrdup_const() as string is known
to be constant.
[kwilczynski: commit log, and add missing Reviewed-by tag]
Link: https://lore.kernel.org/linux-pci/1bad6879083a7d836c8a47418a0afa22485e8f69.1700294127.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/c3a51791d54deaa818b8526975fc4e16ef1090ce.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/06612aff79dfb52d5b0b20129dff5e4b1f04d3a7.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/50de44ea8931465fd9cdc821854ea761cb43adf6.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive PCI
drivers to use the newer symbol.
Link: https://lore.kernel.org/linux-pci/20230918-safeness-cornflake-62278bc3aaaa@wendy
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform
bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
As a result, there's a pretty much random mix of those include files
used throughout the tree. In order to detangle these headers and replace
the implicit includes with struct declarations, users need to explicitly
include the correct includes.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231207165251.2855783-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add suspend/resume support for Layerscape LS1043a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
'pf' and 'lut' are two different acronyms describing the same
thing, basically it is a MMIO base address plus an offset.
Rename them to avoid duplicate pf_* and lut_* naming schemes in the
driver.
Link: https://lore.kernel.org/r/20231204160829.2498703-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Add suspend/resume support for Layerscape LS1021a.
In the suspend path, PME_Turn_Off message is sent to the endpoint to
transition the link to L2/L3_Ready state. In this SoC, there is no way to
check if the controller has received the PME_To_Ack from the endpoint or
not. So to be on the safer side, the driver just waits for
PCIE_PME_TO_L2_TIMEOUT_US before asserting the SoC specific PMXMTTURNOFF
bit to complete the PME_Turn_Off handshake. Then the link would enter L2/L3
state depending on the VAUX supply.
In the resume path, the link is brought back from L2 to L0 by doing a
software reset.
Link: https://lore.kernel.org/r/20231204160829.2498703-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Since different SoCs require different sequences for exiting L2, let's add
a separate "exit_from_l2()" callback to handle SoC specific sequences.
Change ls_pcie_exit_from_l2() return value from void to int in order
to propagate errors. Return an error if the exit_from_l2() callback
fails in the resume flow.
Link: https://lore.kernel.org/r/20231204160829.2498703-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Break up the newly added ASPM comment so that it fits within the soft 80
character limit and becomes more readable.
Link: https://lore.kernel.org/r/20231128081512.19387-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom_pcie_enable_aspm() helper is called from pci_walk_bus() during
host init to enable ASPM.
Since pci_walk_bus() already holds a pci_bus_sem read lock, use
pci_enable_link_state_locked() to enable link states in order to avoid a
potential deadlock (e.g. in case someone takes a write lock before
reacquiring the read lock).
This issue was reported by lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0-rc1 #4 Not tainted
--------------------------------------------
kworker/u16:6/147 is trying to acquire lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_enable_link_state+0x74/0x1e8
but task is already holding lock:
ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Link: https://lore.kernel.org/r/20231128081512.19387-4-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
[bhelgaas: add "potential" in subject since the deadlock has only been
reported by lockdep, include helper name in commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
- Use FIELD_GET()/FIELD_PREP() when possible throughout drivers/pci/ (Ilpo
Järvinen, Bjorn Helgaas)
- Rework DPC control programming for clarity (Ilpo Järvinen)
* pci/field-get:
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
PCI: Use FIELD_GET()
PCI/MSI: Use FIELD_GET/PREP()
PCI/DPC: Use defines with DPC reason fields
PCI/DPC: Use defined fields with DPC_CTL register
PCI/DPC: Use FIELD_GET()
PCI: hotplug: Use FIELD_GET/PREP()
PCI: dwc: Use FIELD_GET/PREP()
PCI: cadence: Use FIELD_GET()
PCI: Use FIELD_GET() to extract Link Width
PCI: mvebu: Use FIELD_PREP() with Link Width
PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
# Conflicts:
# drivers/pci/controller/dwc/pcie-tegra194.c
- Use PCIE_SPEED2MBS_ENC() macro in qcom host and endpoint to encode link
speed instead of hard-coding the link speed in MBps (Manivannan
Sadhasivam)
- Use Mbps_to_icc() (not MBps_to_icc()) in tegra194 instead of explicitly
doing the bytes-to-bits conversion (Manivannan Sadhasivam)
* pci/controller/speed:
PCI: tegra194: Use Mbps_to_icc() macro for setting icc speed
PCI: qcom-ep: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
PCI: qcom: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
