To support ieee80211_ops::set_antenna, the driver can decide if the
antenna mask is accepted, otherwise it can return an error code.
Because each chip could have different limitations, let the chip
check the mask and return.
Also the antenna mask for TRX from upper space is 32-bit long.
Change the antenna mask for rtw_chip_ops::set_antenna from u8 to u32.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410100950.3199-2-yhchuang@realtek.com
Add a new entry "coex_info" in debugfs to dump coex's states for
us to debug on coex's issues.
The basic concept for co-existence (coex, usually for WiFi + BT)
is to decide a strategy based on the current status of WiFi and
BT. So, it means the WiFi driver requires to gather information
from BT side and choose a strategy (TDMA/table/HW settings).
Althrough we can easily check the current status of WiFi, e.g.,
from kernel log or just dump the hardware registers, it is still
very difficult for us to gather so many different types of WiFi
states (such as RFE config, antenna, channel/band, TRX, Power
save). Also we will need BT's information that is stored in
"struct rtw_coex". So it is necessary for us to have a debugfs
that can dump all of the WiFi/BT information required.
Note that to debug on coex related issues, we usually need a
longer period of time of coex_info dump every 2 seconds (for
example, 30 secs, so we should have 15 times of coex_info's
dump).
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200313033008.20070-2-yhchuang@realtek.com
The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the modules use RFE type 3, add corresponding tables
for them.
Tested-by: G.schlmm <g.schlmm@googlemail.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sparse warnings:
drivers/net/wireless/realtek/rtw88/rtw8822b.c:1440:6: sparse: sparse:
symbol 'rtw8822b_pwr_track' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1008:6: sparse: sparse:
symbol 'rtw8822c_pwrtrack_init' was not declared. Should it be static?
Fixes: c97ee3e0be ("rtw88: add power tracking support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit adds several Tx/Rx physical information to phy_info
debugfs for 8822B/8822C. By this debugfs, we can know physical
information, such as Tx/Rx rate, RSSI, EVM,SNR, etc. The
information is gotten from the packets of Tx/Rx path. It has
no impact for the performance of 8822B/8822C.
In the fields, we may meet different kinds of problems, but
we may have no professional instrument to check them. At
this moment, this debugfs is a good tool, and it may provide
useful information for debug.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable MU-MIMO transmit beamformee support for chipset 8822b and 8822c.
If the driver is in station mode and associated with an AP, and the
capabilities of both meet the requirement of beamforming, driver will
run as a beamformee and the corresponding chip settings will be set.
In addition, module parameter support_bf is added to enable or disable
beamforming. Sometimes driver will need to disable for inter-operate
issues, and it would be easier for driver to debug.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The temperature of the chip can affect the output power
of the RF components. Hence driver requires to compensate
the power by adjusting the power index recorded in the
power swing table.
And if the difference of current thermal value to the
default thermal value exceeds a threshold, the RF IQK
should be triggered to re-calibrate the characteristics
of the RF components, to keep the output IQ vectors of
the RF components orthogonal enough.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add macros to see which band we are, based on the current channel.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value of GET_RX_DESC_SWDEC() indicates that if this RX
packet requires software decryption or not. And software
decryption is required when the packet was encrypted and the
hardware failed to decrypt it.
So, GET_RX_DESC_SWDEC() is negative does not mean that this
packet is decrypted, it might just have no encryption at all.
To actually see if the packet is decrypted, driver needs to
further check if the hardware has successfully decrypted it,
with a specific type of encryption algorithm.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since
WiFi and BT use 2.4GHz to transmit, it is important to
make sure they run concurrently without interfering each
other. To achieve this, WiFi driver requires a mechanism
to collaborate with BT, whether they share the antenna(s)
or not.
The final decision made by the co-existence mechanism is
to choose a proper strategy, or called "tdma/table", and
inform either firmware or hardware of the strategy.
To choose a strategy, co-existence mechanism needs to
have enough information from WiFi and BT.
BT information is provided through firmware C2H.
The contents describe the current status of BT, such as
if BT is connected or is idle, or the profile that is
being used.
WiFi information can be provided by WiFi itself. The WiFi
driver will call various of "notify" functions each time
the state of WiFi changed, such as WiFi is going to switch
channel or is connected. Also WiFi driver can know if it
shares antenna with BT by reading efuse content. Antenna
configuration of the module will finally get a different
strategy.
Upon receiving any information from WiFi or BT, the WiFi
driver will run the co-existence mechanism immediately.
It will set the RF antenna configuration according to the
strategy through the TDMA H2C to firmware and a hardware
table. Based on the tdma/table, WiFi + BT should work with
each other, and having a better user experience.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin
And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.
Supported:
* Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)
Missing feature:
* WOW/PNO
* USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
* BT coexistence (8822B/8822C are combo ICs)
* Multiple interfaces (for now single STA is better supported)
* Dynamic hardware calibrations (to improve/stabilize performance)
Potential problems:
* static calibration spends too much time, and it is painful for
driver to leave IDLE state. And slows down associate process.
But reload function are under development, will be added soon!
* TRX statictics misleading, as we are not reporting status correctly,
or say, not reporting for "every" packet.
The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.
Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.
Finally, rtw88 has many authors, listed alphabetically:
Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
