This is needed for AP mode. Otherwise client sees the network, but
can't connect to it.
REG_FWHW_TXQ_CTRL+1 is set to WLAN_TXQ_RPT_EN (0x1F) in common mac
init function (__rtw8723x_mac_init), but the value was overwritten
from mac table later.
Tables with register values for phy parameters initialization are
copied from vendor driver usually. When table will be regenerated,
manual modifications to it may be lost. To avoid regressions in this
case new callback mac_postinit is introduced, that is called after
parameters from table are set.
Tested on rtl8723cs, that reuses rtw8703b driver.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250711084740.3396766-1-andrej.skvortzov@gmail.com
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RTW_WCPU_11AC and RTW_WCPU_11N enums are used to identify two
types of microcontrollers used in Realtek chips, but these names are
misleading. The "11AC" type was also used in 11n devices (e.g.
RTL8733BU, not supported by rtw88), and the "11N" type was also used
in 11ac devices (RTL8821AU, RTL8812AU).
Rename RTW_WCPU_11AC to RTW_WCPU_3081 and RTW_WCPU_11N to RTW_WCPU_8051.
(8051 is well known. It's less clear what 3081 is, but the out of tree
drivers use this name.)
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bfb1099c-db52-4b25-b111-17ab712e9404@gmail.com
Tell the chip the maximum AMPDU size supported by the AP. This greatly
improves the TX speed of RTL8814AU in the 2.4 GHz band. Before: ~90
Mbps. After: ~300 Mbps.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/4edc2a63-81b3-431c-9a37-5a7d899a6cc2@gmail.com
Although the RTL8814AU only has 3 spatial streams, maybe some other chip
has 4.
Correct the TX power index and TX power limit calculations for 3SS and
4SS HT/VHT rates.
With this the RTL8814AU can set the TX power correctly.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d0c0e126-0794-4c4e-9203-ea39a707b673@gmail.com
Some users want to plug two identical USB devices at the same time.
This static variable could theoretically cause them to use incorrect
TX power values.
Move the variable to the caller and pass a pointer to it to
rtw8822b_set_tx_power_index_by_rate().
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/8a60f581-0ab5-4d98-a97d-dd83b605008f@gmail.com
Register a struct led_classdev with the kernel's LED subsystem and
create a throughput-based trigger for it. Then mac80211 makes the LED
blink.
Tested with Tenda U12 (RTL8812AU), Tenda U9 (RTL8811CU), TP-Link Archer
T2U Nano (RTL8811AU), TP-Link Archer T3U Plus (RTL8812BU), Edimax
EW-7611UCB (RTL8821AU), LM842 (RTL8822CU).
Also tested with devices which don't have LEDs: the laptop's internal
RTL8822CE and a no-name RTL8723DU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/6c43451f-ab2f-4e76-ac6e-ff5a18dd981d@gmail.com
RTL8812AU uses one set of TX power tracking tables for RFE 3, and
another set for everything else.
Move pwr_track_tbl from struct rtw_chip_info to struct rtw_rfe_def in
order to load the right set of tables for each RFE (RF front end) type.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/904d0ab1-c046-40cd-a3a3-d4fdcf663c9d@gmail.com
RTL8811AU fails to perform the 4-way handshake when the AP is too far
because it transmits the EAPOL frames at MCS9 and when that doesn't
work it retries 48 times with the same rate, to no avail.
Retrying 48 times with the same rate seems pointless. Set the
appropriate field in the TX descriptor to allow it to use lower rates
when retrying.
Set it for RTL8723D and RTL8703B because they interpret this field the
same way as RTL8811A.
The newer RTL8822C, RTL8822B, RTL8821C seem to interpret this field in
the TX descriptor differently, so leave it alone for those chips.
Tested with RTL8811AU and RTL8723DU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/2b3e3e6f-541b-4a3b-8ca3-65b267e6a95a@gmail.com
RTL8821AU and RTL8812AU have to do some things differently, so let
them have full control.
The other chips use the same functions as before.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/98ab839f-9100-44ae-9551-9af743a4aa3a@gmail.com
The RTL8821AU and RTL8812AU have smaller RA report size, only 4 bytes.
Avoid the "invalid ra report c2h length" error.
Also, use a struct and u8_get_bits() to access the RA report C2H.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c3e73c3a-fb2f-4013-9f06-d5274211e282@gmail.com
rtw8703b_query_rx_desc(), rtw8723d_query_rx_desc(),
rtw8821c_query_rx_desc(), rtw8822b_query_rx_desc(), and
rtw8822c_query_rx_desc() are almost identical, so replace them all with
a single function, rtw_rx_query_rx_desc().
Also, access the RX descriptor using a struct with __le32 members and
le32_get_bits().
Tested with RTL8811CU, RTL8811AU, and RTL8812AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Tested-by: Ping-Ke Shih <pkshih@realtek.com> # RTL8723DE and RTL8822CE
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/913f1747-38fc-4409-85a4-57bb9cee506b@gmail.com
The Realtek wifi 5 devices which support USB 3 are weird: when first
plugged in, they pretend to be USB 2. The driver needs to send some
commands to the device, which make it disappear and come back as a
USB 3 device.
Implement the required commands in rtw88.
When a USB 3 device is plugged into a USB 2 port, rtw88 will try to
switch it to USB 3 mode only once. The device will disappear and come
back still in USB 2 mode, of course.
Some people experience heavy interference in the 2.4 GHz band in
USB 3 mode, so add a module parameter switch_usb_mode with the
default value 1 to let people disable the switching.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/77906c62-5674-426f-bde1-1b2a12a0339d@gmail.com
Currently the number of frames sent to the chip in a single USB Request
Block is limited only by the size of the TX buffer, which is 20 KiB.
Testing reveals that as many as 13 frames get aggregated. This is more
than what any of the chips would like to receive. RTL8822CU, RTL8822BU,
and RTL8821CU want at most 3 frames, and RTL8723DU wants only 1 frame
per URB.
RTL8723DU in particular reliably malfunctions during a speed test if it
receives more than 1 frame per URB. All traffic seems to stop. Pinging
the AP no longer works.
Fix this problem by limiting the number of frames sent to the chip in a
single URB according to what each chip likes.
Also configure RTL8822CU, RTL8822BU, and RTL8821CU to expect 3 frames
per URB.
RTL8703B may or may not be found in USB devices. Declare that it wants
only 1 frame per URB, just in case.
Tested with RTL8723DU and RTL8811CU.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cb46ea35-7e59-4742-9c1f-01ceeaad36fb@gmail.com
Extend 8822c's reserved page number to accommodate additional required
pages. Reserved page is an area of memory in the FIFO dedicated for
special purposes. Previously only one interface is supported so 8 pages
should suffice, extend it so we can support 2 interfaces concurrently.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-4-pkshih@realtek.com
The efuse of the SDIO RTL8822BS chip has only one known member: the mac
address is at offset 0x11a. Add a struct rtw8822bs_efuse describing this
and use it for copying the mac address when the SDIO bus is used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230218152944.48842-5-martin.blumenstingl@googlemail.com
Some WSC IEs require size larger than we current supports. Extend size
to fit those demands. Separate the registered scan IE length by IC so
settings can be independent.
Since old firmware uses fewer page number, define a firmware feature to
be compatible with various firmware version.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-2-pkshih@realtek.com
Sparse lists the following for rtw88:
CHECK drivers/net/wireless/realtek/rtw88/rtw8822b.c
drivers/net/wireless/realtek/rtw88/rtw8822b.c:2500:22: warning: symbol 'rtw8822b_hw_spec' was not declared. Should it be static?
The warning arises because the external declaration for rtw8822b_hw_spec
occurs in rtw8822be.h, which is not included in rtw8822b.h. That line is
moved, and the now empty file rtw8822be.h is deleted.
Symbol 'rtw8822b_hw_spec' can be made constant.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524153621.19027-2-Larry.Finger@lwfinger.net
Each chip have best ampdu density value, the correct setting can improve
throughput performance.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-1-pkshih@realtek.com
To keep high sensitivity reaction, Bluetooth gaming controller will send
packet very frequently, it will make WLAN performance very poor. To solve
this situation, MIMO PS mechanism makes WLAN/BT own an antenna itself, WLAN
quits 2SS performance but it can get a stable 1SS performance and Bluetooth
gaming controller can keep sensitivity reaction at the same time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-5-pkshih@realtek.com
These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
Currently all realtek wifi chip is set to check CRC of VHT-SIG-B
in 802.11ac signal, but some AP don't calculate the CRC and packets
from these AP can't be received and lead to disconnection.
We disable the check defaultly to avoid this case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012421.7859-1-pkshih@realtek.com
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.
By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
Mapping table from country code to rtw_regulatory, which manages tx power
limit according to countries, is updated. And mapping architecture is also
upgraded. For more precise control on tx power limit, it allows different
rtw_regulatory for different bands logically. Besides, a helper function
to query rtw_regulatory for current band under current country is provided.
For older chips, some newly added rtw_regulatory may not be configured.
To avoid that those chips have no limit on some countries mapping to a
newer rtw_regulatory after table update, a backward selection mechanism
of rtw_regulatory is introduced. It can help chips use a rtw_regulatory
which has been configured as an alternative of a newer one which is not
configured.
In addition, rtw88 actually doesn't manage channel plans by itself.
Instead, it follows them from stack. So, correct some naming about
chplan with regd, and remove the unnecessary channel control for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-2-pkshih@realtek.com
Add modifications for A2DP interoperability issue of TWS earphones.
Some TWS earphones has low buffer size, so it's necessary to reduce
the slot period to let it get data more frequently.
(e.g. use 4-slot to replace the original 2-slot method).
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-10-pkshih@realtek.com
Since coexistence issue is related to WL/BT and each digital/analog/rf,
and these issues are often critical with low failure rate, add more
debugging information is helpful to clarify issues.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-11-pkshih@realtek.com
Adaptive Frequency Hopping(AFH) is a method of transmitting
radio signals by rapidly changing the carrier frequency among
many distinct frequencies, which can avoid interference.
Add this feature to update AFH parameter for 8822b.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-10-pkshih@realtek.com
Update COEX parameters and logic to enhance WL/BT performance
while WL_Busy + A2DP in a less interference environment.
It can avoid the interference comes cross from each other
and earned more performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-3-pkshih@realtek.com
Some register definition and bit definition were incorrect.
e.g. REG_BT_COEX_V2 should be word alignment to meet the coding style.
e.g. set REG_BT_TDMA_TIME[5:0]=0x5,
But the original is to set REG_BT_TDMA_TIME[7:0]=0x5.
This will cause unexpected hardware behavior.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-2-pkshih@realtek.com
BT firmware will report BLE-HID and BLE-RCU in different profile.
We can distinguish the two profile from BT info now.
Add the coexistence for BLE-HID coexistence,
it can make BLE HID work more smoothly.
BLE-HID need to Tx/Rx packet more frequently to respond
user operation, but RCU doesn't.
In the case of RCU coexistence, it will make Wi-Fi have a
higher priority to earn more Wi-Fi throughput.
If BLE-HID go for the same case,
it will make user feel mouse is lagging.
Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030055506.6560-1-pkshih@realtek.com
clang -Wextra warns about functions returning a 'const' integer:
drivers/net/wireless/realtek/rtw88/rtw8822b.c:90:8: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
static const u8 rtw8822b_get_swing_index(struct rtw_dev *rtwdev)
Remove the extra qualifier here.
Fixes: c97ee3e0be ("rtw88: add power tracking support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-7-arnd@kernel.org
Rtw88 currently has a function to dump reserved page section of the
firmware fifo. Reserved page is just part of the firmware fifo, there
are multiple sections in the firmware fifo for different usages, such as
firmware rx fifo and tx fifo.
This commit adds a function to check not only the reserved page section
but also other parts of the firmware fifo. In addition, we need to dump
firmware fifo to dump the debug log message if firmware crashes.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-4-tehuang@realtek.com
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
Make objects about 8822b functions and 8822b tables,
i.e. rtw8822b.o and rtw8822b_table.o, an individual
kernel module called rtw88_8822b.ko.
For 8822b pcie chip, i.e. 8822BE chip, add a chip
entry point module called rtw88_8822be.ko which
will depend on rtw88_8822b.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-5-yhchuang@realtek.com
Since 8723D use different address of ltecoex register, this commit add a
new field in chip_info and fill proper address. Then, ltecoex_read_reg()
and ltecoex_reg_write() can use them to access ltecoex according to chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-7-yhchuang@realtek.com
Flush queue is used to check if queue is empty, before doing something
else. Since 8723D uses different registers and page number of
availabl/reserved occupy 8 bits instead of 16 bits, so use a 'wsize' field
to discriminate which rtw_read{8,16} is adopted.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-6-yhchuang@realtek.com
DIG sets only one IG register for most chips, but 8723D need to set
additional register for CCK rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-8-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.
Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.
Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
