If there is an ongoing scan that lasts long, the MPDU counters may not
increase enough due the device being busy with scanning and not
because we are in a low throughput scenario.
In that case we don't want to block EMLSR.
Instead, stop checking the counters from the moment we started
scanning, and when the scan ends - clear the counters and schedule a
check in 5 seconds, as usual.
Note that this is only done for regular scan since MLO scan is too short
to affect the counters, and scheduled scan is mainly used when we are
not connected.
Also note that we only stop checking whether to block EMLSR, and not if to
unblock.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.330ea440d19c.Ib10dae0b7a0cb0e10c59a9edf5ff7af0f065ac60@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
There's no need to build a list of individual configs
first and then compare them, we can just go through all
of them and compare if the pointers aren't the same.
The complexity (in terms of number of comparisons) is a
bit higher that way, but it's just a test and the code
complexity is much lower without that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.85911c59d96a.I540f464229da3566d1726dfb61b46002fbb73bde@changeid
For different MACs we maintain the configs in different
files, and while it's a small waste of space, this is a
worthwhile trade-off for maintenance and simplicity. So
allow different MAC types to have the same config. This
could allow the same config for two MACs in the same MAC
family, but that's not hugely important. Also simplify
the test to not build a config list, there's no good
reason to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.27f5d570eb32.I1649309a0e54a1d446a38c5b2124a582de9f6d61@changeid
No hardware that uses iwlmvm actually supports HT greenfield.
Remove the support and then clean up the v1 rate API by doing
a conversion to v2 rate API, the only thing v1 covered that
couldn't be done in v2 was HT greenfield.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.805ec090c61f.Iafd87f62ceb463b72f861a5348078999dcaace92@changeid
This is ephemeral data that's passed from the alive
response to the PNVM loading, so it doesn't need to
be stored. Pass it around instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.fe8be4454007.I24824f35620b21fe49e9243818c7188e431af48e@changeid
This really belongs there, it's needed early, so move it. Remove
the related but dead iwl_trans_pcie_ctx_info_gen3_set_step() while
at it. In iwlmld move the calls since they do part of the trans
configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.a4681ee11dd7.I6434a13d51932e984bb07695bc1cb931ebdcd27c@changeid
Instead of having a trans_configure method that copies all
the data, just have the users set up the configuration in
the transport directly. This simplifies the code on both
sides. While doing so also move some value from the trans
struct into the conf struct because they are configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.e2a2535ecfd0.I21653103ff02afc5a4d97a41b68021f053985e37@changeid
Add a new device information 'info' substruct to the transport
that's const and can only be set by a special helper, and move
some information there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.cd80cb55403c.Ic18524b66d655fad734bf97192a54d9cfa9fdf1f@changeid
We pass this parameter around a lot of places just to
validate what the firmware told us against the hardware
with a warning, which seems to never trigger. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.5405014d7f88.I3b74a1fd51a39c6df5674f2994189092d1635e7f@changeid
The rate validation in mac80211 considers a rate to be valid iff both
the rate index and the count are positive. When the rate scaling is
managed in the driver and not enough traffic passed to set the actual
rate, the driver set the rate to be the optimal rate. However, the rate
count is not set and thus the rate is considered not valid. Fix it by
setting the count to 1.
Fixes: 3e99b4d282 ("wifi: mac80211: Sanity check tx bitrate if not provided by driver")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.0d1d1e022d63.I76833c14ba1d66f9bea5c32b25a54d8b36f229ba@changeid
The code currently passes only the specific image that should
be loaded, but then has to pass the IML (image loader) out of
band, which is confusing. Pass the full FW data together with
desired image type, and use the IML from that.
This also cleans up the code in the various sub-drivers a bit
as they no longer have to look up and check for the image.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224231.eac4006e81c5.Iebadc56bb2762e5f4d71f66bb2609d74b33daf11@changeid
FW sends new notification version 2 indicating whether activating EMLSR
mode is recommended or not. If recommendation is to leave EMLSR or force
leave then FW sends the reason. Add debug log for the reason sent by FW.
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224231.0582726248a4.I9d1d00eb98d10a3a742cb3e06665ce10e5ec93f0@changeid
Simplify the logic here by tracking only suspended as a
status bit, and remove CMD_SEND_IN_D3 completely. There
is no value, since the op-mode sets the state and also
sends the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224231.cc3360761f1e.I72261afc42cee8983198b4660b7d38b7df7963da@changeid
* stack
- free SKBTX_WIFI_STATUS flag
- fixes for VLAN multicast in multi-link
- improve codel parameters (revert some old twiddling)
* ath12k
- Enable AHB support for IPQ5332.
- Add monitor interface support to QCN9274.
- Add MLO support to WCN7850.
- Add 802.11d scan offload support to WCN7850.
* ath11k
- Restore hibernation support
* iwlwifi
- EMLSR on two 5 GHz links
* mwifiex
- cleanups/refactoring
along with many other small features/cleanups
-----BEGIN PGP SIGNATURE-----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=s9mS
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless features, notably
* stack
- free SKBTX_WIFI_STATUS flag
- fixes for VLAN multicast in multi-link
- improve codel parameters (revert some old twiddling)
* ath12k
- Enable AHB support for IPQ5332.
- Add monitor interface support to QCN9274.
- Add MLO support to WCN7850.
- Add 802.11d scan offload support to WCN7850.
* ath11k
- Restore hibernation support
* iwlwifi
- EMLSR on two 5 GHz links
* mwifiex
- cleanups/refactoring
along with many other small features/cleanups
* tag 'wireless-next-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (177 commits)
Revert "wifi: iwlwifi: clean up config macro"
wifi: iwlwifi: move phy_filters to fw_runtime
wifi: iwlwifi: pcie: make sure to lock rxq->read
wifi: iwlwifi: add definitions for iwl_mac_power_cmd version 2
wifi: iwlwifi: clean up config macro
wifi: iwlwifi: mld: simplify iwl_mld_rx_fill_status()
wifi: iwlwifi: mld: rx: simplify channel handling
wifi: iwlwifi: clean up band in RX metadata
wifi: iwlwifi: mld: skip unknown FW channel load values
wifi: iwlwifi: define API for external FSEQ images
wifi: iwlwifi: mld: allow EMLSR on separated 5 GHz subbands
wifi: iwlwifi: mld: use cfg80211_chandef_get_width()
wifi: iwlwifi: mld: fix iwl_mld_emlsr_disallowed_with_link() return
wifi: iwlwifi: mld: clarify variable type
wifi: iwlwifi: pcie: add support for the reset handshake in MSI
wifi: mac80211_hwsim: Prevent tsf from setting if beacon is disabled
wifi: mac80211: restructure tx profile retrieval for MLO MBSSID
wifi: nl80211: add link id of transmitted profile for MLO MBSSID
wifi: ieee80211: Add helpers to fetch EMLSR delay and timeout values
wifi: mac80211: update ML STA with EML capabilities
...
====================
Link: https://patch.msgid.link/20250506174656.119970-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no reason for pcie code to call itself indirectly,
directly use the pcie functions instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Yedidya Ben Shimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.52db0b9fba15.I062e766ded86f61ec86104c28b84767f1c29ea78@changeid
Since there are two bytes hole in struct iwl_dev_info, add
a subdev_mask to match with. Also, since the PCI IDs list
needs to match first, and the dev-info list is matched from
the bottom up, remove unnecessary entries.
With this, even though there are new entries from previous
changes, the overall size is slightly reduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.689f9b335cbe.I66f1344b6ac7aa3665696637c97fa843c2307423@changeid
A long time ago, when transport vs. device configs were
introduced, we wanted to eventually have a list of PCI
IDs and a separate list of devices, but for simplicity
embedded the transport config in the whole config, and
it all got confusing.
Finish splitting that out. Doing so requires having more
IWL_DEV_INFO() entries, but the whole trans/cfg aliasing
goes away and the code becomes a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.e03f65c0f693.I076a997f800db455b575008f9488b151738ad7ec@changeid
Remove the erroneously named IWL_DEVICE_BZ_COMMON macro
from the Sc file and fix some indentation. Also bump the
minimum FW version since it's not released yet anyway,
right now this is mostly to make the config different
from iwl_bz_cfg which would otherwise be the same with
the upcoming transport config cleanups.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.b313d54b8809.Ia975b6d5460996f2a2761dd3d0fef4a56f1f3e24@changeid
It's not clear that it makes sense to have any matches
for IWL_CFG_ANY for this bit, but let's assume for now
that this makes sense. Then, it's clearer to call this
BW_NOT_LIMITED rather than BW_NO_LIMIT, since the last
change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.9b39693b505c.Ib47aa6a072a0e61bbba28383ce54764cd859f19c@changeid
The BW limit, cores and RF ID are matched in the subdevice ID,
so it doesn't really make sense to have both SUBDEV() match and
a match on any of those three. In particular, for Killer devices
the subdevice ID doesn't even follow the layout, so no matching
should be on those three values at all, only with SUBDEV().
Change the logic around the BW limit to have it more like all
the other things: only a bw_limit match in the dev_info, and
put the actual bandwidth into struct iwl_cfg. This duplicates a
number of those values, but that way the logic is clearer.
Add a test that checks that the three matches mentioned above
are not used in conjunction with SUBDEV(), and check that if
the bw_limit is matched, a BW limit is provided in the config.
Also check that the "Killer" devices have a SUBDEV() match.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.a185eac2736c.I87ee87300c92518a1d3296d3eda9fd4163e9085e@changeid
This really is the same device as covered by iwl_cfg_bz,
just the discrete version. Since discrete vs integrated
is handled in the transport config, there's no need to
have both. Remove iwl_cfg_gl.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.fbb78183dc85.Ic5429009677ae1023cf1f43a655e90409a30c493@changeid
This was used in some really old devices, and then got
carried forward to Qu devices, even though on those we
don't need it at all since the TX aggregation start is
offloaded to the firmware. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.9c2689e2ca8e.I8274b29ca64d9ef9d1e357bbe34ca3a4b97aeb7a@changeid
Now that the fw_name_mac is no longer around and derived
from the MAC type automatically, we no longer need to have
different configurations for Qu/QuZ. Combine them. For the
killer AX1650s/i, also fix the names, there was a mixup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.957fbb5437ce.If51ad0b2c8afaaa131208125af3bc292793613bb@changeid
This was used in the past for NoA and/or beacon filter
testing, but these days everything is tested via debugfs
or special FW commands, so remove the testmode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.751018e0ed8e.I21557a9a3d57234187f1b0b2182a1714ecc66b9a@changeid
When a soft AP is started, it may not use the full configured
bandwidth (e.g. if no station is connected). As a result, the
responder will not support the configured bandwidth. Since the
responder supports ranging with unassociated stations, there is
no indication to the driver when the full bandwidth should be enabled.
Fix it by configuring the AP to always use the full bandwidth when a
responder is supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.620fe8099fff.Id50675f4d4c524b0a7ee602c48af538a327010e0@changeid
When a channel context is added, it is still not assigned to the link
and the link is not yet active. As a result, the channel context
min_def is used when the AP is started, even when the full bandwidth
should be used.
Fix it by updating the PHY channel context when the link is already
active so the full bandwidth is used when needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.30b043b10fb1.I62c2aa58687e4796b759fa68132122119a337b49@changeid
This version fixes the issue that was worked around by
iwl_mvm_smps_workaround. So for FWs with the new version don't do the
workaround, and set new bit added in this version when appropriate.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250430155443.5c9a0181a84b.I9a03bc07a7b3f6e37cc1c0c1af5719e765a05897@changeid
Implement TOP reset (new in the SC family), which resets much
of the (shared) hardware without resetting the bus interfaces.
Use it to recover from TOP fatal error, or if manually used;
we'll need to add using it for FSEQ updates later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.12f38024a3b4.I9c22f6c4f6de64f3b34ccd898370ec1859ab7dbf@changeid
This version fixes the issue that was worked around by
iwl_mld_smps_wa. So for FWs with the new version don't do the
workaround, and set new bit added in this version when appropriate.
While at it, rename iwl_mld_smps_wa to iwl_mld_smps_workaround.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250430155443.77fdb18d1ee0.I93688612ac4f6ec99da9bc54bee16554ef40a40b@changeid
PPAG command version 7 will send exact data read from BIOS to
firmware without filtering/altering BIOS data. This enables the
driver to become purely a pipe for this feature.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.88ed7b2cadef.Iad78f6cec617d1f111b704352795dde81af71a99@changeid
ppag_ver variable is holding PPAG BIOS revision but name misleading
as PPAG command API version, So rename to ppag_bios_rev.
This will improve code readability but doesn't alter behaviour.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.be51850947df.If81d88cd2d38299faf1e2a3db5efbc021650f907@changeid
If iwl_mld_change_vif_links failed to add the requested link(s)
because the FW is dead (error before recovery), there is no point
in returning an error value, as the reconfig will re-add the link(s)
after the FW is started.
Return 0 in that case, and WARN in the others.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250430151952.c549c72b1f37.I445bf723e9befc9541b4abd0ec7c72db8f1ff177@changeid
When BT is ON, EMLSR with one of the links operating on 2.4 GHz
is allowed only if it meets following conditions.
In this patch:
1. during link selection, when BT is ON, allow emlsr only if BT
pentalty is < 7%.
2. exit EMLSR if BT is turned ON and one of the links is operating
on 2.4 GHz with BT penalty > 7%
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.d30212ec3901.I48e3d5bd6b0b8583f98057c38d2ee30fff5abd8a@changeid
For the upcoming SC hardware, a new reset mode "(silent) TOP
reset" will be available. When BT initiates that reset, it'll
negotiate with the WiFi firmware which makes it appear to the
driver as the reset interrupt. To distinguish it from all the
other reasons for the reset interrupt, there's (now) a status
field in CSR 0x110.
Implement the part of TOP reset where we react to BT doing it.
This requires disambiguating the interrupt, depending on the
state of the device, since we can even get TOP reset from BT
while waiting for the reset handshake.
If TOP reset is done by BT while we're not trying to do reset
anyway, then simply reprobe, since we cannot keep the state
of the device as it's being reset, after waiting the needed
180ms to let the device reset/settle.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.fb86bfbdca40.Ibe40bf54003e3f8929b671324a395e76eb64a4d8@changeid
When a restart is in progress, it can be async due to the next
worker being scheduled in mac80211 (restart work) or the driver
itself (reprobe). Avoid scheduling another restart during this
period.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.db428503ec3c.I3f2be3d72a9d40cfb4e697cdab1cd2866a9262bc@changeid
Generalize and extend the link pair tests to not just do
channel load checks, but generally check link pairs. To
enable more accurate checking, return the reasons bitmap
from iwl_mld_valid_emlsr_pair() and therefore rename it
to iwl_mld_emlsr_pair_state.
It's also necessary now to add more chandefs, and while
doing so fix the existing ones to be valid and add a
test to check they really are valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.1f7c4ac75c6d.I69d68359e02d99632e95daba3d126115dce167b3@changeid
We are currently reading it only from ACPI, but we need to read it from
UEFI too (if exists, and if the UEFI variables are locked)
Add the reading from the UEFI and use IWL_BIOS_TABLE_LOADER to generate
the code that determines the source from which the table should be read
(ACPI/UEFI).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.839a5e7dd89b.I491acbf68047874df97b3971f1ba692ebc998a52@changeid
IWL_BIOS_TABLE_LOADER generates the code that determines from what source
to read a BIOS table (ACPI or UEFI).
As we want to read WPFC from UEFI to, iwl_acpi_get_phy_filters needs to
have the prototype that is required by this macro:
receive fwrt and return a int on success/failure.
Do that.
This allowes us to make to version of iwl_acpi_get_phy_filters for non
ACPI builds back to an iniline function.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Link: https://patch.msgid.link/20250430151952.8046a2db775b.Ifbcf4168183d3cd635e3e800ec7ecd903e57d361@changeid
The kernel-doc script flagged the following:
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:130: warning: missing initial short description on line:
* enum iwl_power_scheme
1 warnings as Errors
Add a short description to address this warning.
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250319-iwl_power_scheme-kdoc-v1-1-2033ae38b178@oss.qualcomm.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
This reverts commit b6abf63ed7.
This is causing major merge conflicts with the changes in
wireless, where we reverted some changes. Revert this for
now to avoid having to solve that problem. We can redo it
on top of wireless-next with wireless merged back later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
phy_filters holds the values as read from WFPC BIOS table.
Since also iwlmld is going to need it, move it to fw_runtime.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250424153620.357baa65950a.I01d22328b4c381d4c0064ad9bd36750911157f90@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rxq->read is accessed without the rxq->lock in a few places,
Make sure to have the lock there.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250424153620.73725f207aaa.I1a3e4b6c5fd370e029fdacfcdc9ee335788afa98@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This version has a new flag bit that indicates whether or not SMPS is
allowed for the MAC.
This only adds the API, the actual support will be done in other
patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250424153620.991ff01b8d16.Id0aa4061d7926753b03a13bf94ec1ac9e1d18745@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IWL_DEV_INFO() macro has far too many arguments, and most
of the time they're just "ANY". Use C99 initializers in the
macro to clean that up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.877b65b940b5.Ic3a40afcd182b6e1802bb8f8a1a845b20608e328@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move some code that's only done when having received data out
of iwl_mld_rx_fill_status() and remove the two arguments that
are related to that. This simplifies the function for the no-
data case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.77010d6a6694.I2fd06b073460717d324245482110cb0381218526@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use u8_get_bits() instead of open-coding, and adjust the
name as well. Also don't use enum nl80211_band for the
variable holding an entirely different type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.c41058510800.Ic3f16ce2f0c991fde2cfe7bcd58ee3b875575fce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware statistics were previously reporting bogus/old
channel load values if the device hadn't been active on a
given channel; it'll report an unknown value now for those
statistics affected (channel_load and channel_load_not_by_us.)
Handle that by simply skipping the value, the averaging would
result in the exact same value as before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.db5410318642.I4d2981f68b915ad335bb02c926e9289c2a60ea6c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware will support external FSEQ images, define the
necessary API for that. We're not yet using/shipping such,
so don't add code to load them for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.4f5acc3dff6c.Ic559d90376945c78495352a0d24b1d44ef887f2d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are two links on 5 GHz subbands that are separated
enough (using channels 36-64 and 100+) then we can support
EMLSR across those two links. Allow that in the logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.d568a26661d5.Ie4277945272c5bbf637957704fda34ea03ef28d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return type of iwl_mld_emlsr_disallowed_with_link() is a u32
bitmap of exit reasons, but in the data structure confusion case
where the warning triggers, it returns false. Add a new reason
bit for this case so it doesn't return that EMLSR is possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.d1f8465e2b5e.I58c463c70801231a79b04c1ff600f41afcbb04f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In iwl_mld_emlsr_disallowed_with_link() the code uses an
enum for a bitmap of values from it, which doesn't really
make sense.Use u32 for the variable just like the return
value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250424153620.ddf54a728ec0.Ie2e8de150f67369c4e034452c5f1a15f85d2931c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* iwlwifi: various regression and iwlmld fixes
* mac80211: fix TX frames in monitor mode
* brcmfmac: error handling for firmware load
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEpeA8sTs3M8SN2hR410qiO8sPaAAFAmgKKK0ACgkQ10qiO8sP
aADVRxAAjf7m5Owl/3euI+wQbuYQql0F+82eoukbqWgMUKioYzWf/5N5fjtJrAn8
0LW2O23/HHlK2Y4dqIJR3oRm+zvAQftCTr9Eqd0bC/hpT/1FBOujqagtdTNkpMSH
qH+ExoJjpbMfuNeq3Jok2BgI82pM39vHDVL4c/EebaoNoVrwTU4y6B/nmbpOajMF
V75spwaX1vnmdgmZdWXb+4MbH9r78Bj4CjGJ7PGXBvsepiZnNUtkFDUeqjJJcSCH
wAQn2cv2iC1HGGDIDYe2fmO8ChnNfwiBJmWcO70CiWRrb2SXfv93nZucaWWRbD27
5PiJnzII9CkyTEIrR47nV3xS9pw34Zov5MPRvqZi96WfYWchPVsm0fUIDWthGO+P
RqCWJsl5z5aI2O6OlTRr7oPXCVPiD5Womv76ptjQhxls73AXv60ox/EMoCu2Mw9u
XfZYJckjhBobOSgLJ+3bNJW22Mm5ZycLZcZo1/zjt4DpB2boAF2WYiJ1TFaQpir6
9azBHJ8YqqniipZUsT0wDyQh+24SU97peXaF/Z0g+D55EboxcWMsGLOLZaahEhMv
BZdRo71j1XPr4jluvOyHq6su/s1pspVnWw7+xChtV2PqZT5Ce/oxk+wuUWykNEQ3
ZSJ2TgVkbkjeY+TWNdAKvtiS21SsVNB4rGlt3ZDNHuWnann7OOs=
=c/97
-----END PGP SIGNATURE-----
Merge tag 'wireless-2025-04-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Some more fixes, notably:
* iwlwifi: various regression and iwlmld fixes
* mac80211: fix TX frames in monitor mode
* brcmfmac: error handling for firmware load
* tag 'wireless-2025-04-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: restore missing initialization of async_handlers_list
wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage()
wifi: plfxlc: Remove erroneous assert in plfxlc_mac_release
wifi: iwlwifi: fix the check for the SCRATCH register upon resume
wifi: iwlwifi: don't warn if the NIC is gone in resume
wifi: iwlwifi: mld: fix BAID validity check
wifi: iwlwifi: back off on continuous errors
wifi: iwlwifi: mld: only create debugfs symlink if it does not exist
wifi: iwlwifi: mld: inform trans on init failure
wifi: iwlwifi: mld: properly handle async notification in op mode start
Revert "wifi: iwlwifi: make no_160 more generic"
Revert "wifi: iwlwifi: add support for BE213"
wifi: mac80211: restore monitor for outgoing frames
====================
Link: https://patch.msgid.link/20250424120535.56499-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This has nothing to do with the opmode. Set it in the transport layer
instead.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250423091408.4e288f7897be.I0c8f792ea2ed6967f8c6d8181f9c5f74bbec7d18@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If starting the op mode failed, the opmode memory is being freed,
so trans->op_mode needs to be NULLified. Otherwise, trans will access
already freed memory.
Call iwl_trans_op_mode_leave in that case.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.c7e178748ef7.Ifaf15bdd8ef8c59e04effbd2e7aa0034b30eeacb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From the moment that we have ALIVE, we can receive notification that
are handled asynchronously.
Some notifications (for example iwl_rfi_support_notif) requires an
operational FW. So we need to make sure that they were handled in
iwl_op_mode_mld_start before we stop the FW. Flush the async_handlers_wk
there to achieve that.
Also, if loading the FW in op mode start failed, we need to cancel
these notifications, as they are from a dead FW.
More than that, not doing so can cause us to access freed memory
if async_handlers_wk is executed after ieee80211_free_hw is called.
Fix this by canceling all async notifications if a failure occurred in
init (after ALIVE).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.a8f63d983466.Ifd77d9c1a29fdd278b0a7bfc2709dd5d5e5efdb1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To cancel all async notifications, we need to:
- cancel async_handlers_wk
- empty async_handlers_list
Instead of having the callers to do both, do it in
iwl_mld_purge_async_handlers_list and rename it accordingly.
Note that the caller iwl_cleanup_mld didn't cancel the work, but it is
harmless.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.e98aed77e836.Id9f858d9d553d406a24165b09db830df111befce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If iwl_mld_load_fw failed, we call iwl_mld_stop_fw which does, among the
others, iwl_trans_stop_device. But this is already called from
iwl_mld_load_fw's error path.
Since we do need the other stuff of iwl_mld_stop_fw to be done also in
the error path of iwl_mld_load_fw, just call it there.
This also makes the call to iwl_fw_flush_dumps in
iwl_mld_op_mope_start redundant, since it is the same as iwl_fw_dbg_stop_sync.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.f7d86be570d3.Ied68f0c4d126b3b0f1ffd9990bbc43d97f098e24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mld_run_fw_init_sequence used to be the last thing done in
iwl_mld_load_fw, and if it failed, it called iwl_trans_stop_hw.
Now we also have there iwl_mld_init_mcc, and it can fail.
In that case, we need to undo what we did so far, which is basically only
iwl_trans_stop_device. Do that.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.ba06d972a57b.I317fb7b10ed8a688a0d92c5d99de8765d8044b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
allocating mld->nvm_data used to be the last thing done in
iwl_mld_load_fw, so there was no need to free on any error path of
iwl_mld_load_fw.
But now iwl_mld_load_fw also calls iwl_mld_init_mcc, that can fail,
after allocating nvm->data. In that case, it is not freed.
As allocating the NVM data should only be done at op mode start anyway,
simply move it to there, where it is already freed in the right error
paths.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.d07469f866ac.I84ad2e624ce7cd4a661c73b4942186e50cdf82b2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We never ask the firmware to store the beacon, so it won't ever send the
notification.
Remove the handling of that notification.
Remove that notification from the arrays of the notifications' names and
add the ones that we forgot to add.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423091408.2bb3ea3ff79b.Ie8f1d89f59d45a960a5fe63e7b717527251350ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the FW is tracking the CT window by itself, we don't need
to update the MAC context or even fill in the value. We just had
added that because a firmware bug had broken it for a while.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423091408.ee164b464c21.I29de491b4d74b2b8084e54bfbd28646b15dee196@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Configure 20 MHz AP mode based on NVM settings, set the
NL80211_RRF_ALLOW_20MHZ_ACTIVITY flag, when the NVM indicates
that an access point can operate in 20 MHz only.
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423091408.897d826a8612.I1f7f84f4485ed3928070c97a031110ccb608bda8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Earlier, the firmware could only request the reset handshake is
done during the dump, if the dump was split. However, it's also
needed when the dump isn't split, in which case it must be done
before the dump. The firmware now advertises this requirement,
so do the handshake in the non-split case when asked for.
Rename apply policy ..._RESET_HANDSHAKE to ..._SPLIT_DUMP_RESET
to more clearly indicate that this specific dump needs to be
split, while the handshake requirement overall is now indicated
by the new capability flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423091408.10adafedb74b.Ie3911db1ebbd196ae4b0de1c53012aa1de193c0d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This state can never be entered, since the last place using it was
removed with non-DQA mode in commit c8f54701bd ("iwlwifi: mvm:
remove non-DQA mode"). Clean up this code too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423091408.e8a20fb41dc5.I9cd41a15148c90e953335e7020405103ba3fc7f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Use the `DEFINE_RAW_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c:6430:41: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/Z-SV8gb6MuZJmmhe@kspp
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initialization of async_handlers_list
was accidentally removed in a previous change.
This patch restores the missing initialization
to ensure proper handler registration.
Fixes: 6895d74c11 ("wifi: iwlwifi: mld: initialize regulatory early")
Signed-off-by: Itamar Shalev <itamar.shalev@intel.com>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250423092503.35206-1-itamar.shalev@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can't rely on the SCRATCH register being 0 on platform that power
gate the NIC in S3. Even in those platforms, the SCRATCH register is
still returning 0x1010000.
Make sure that we understand that those platforms have powered off the
device.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219597
Fixes: cb347bd29d ("wifi: iwlwifi: mvm: fix hibernation")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.a7e082ee785c.I9418d76f860f54261cfa89e1f7ac10300904ba40@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some BIOSes decide to power gate the WLAN device during S3. Since
iwlwifi doesn't expect this, it gets very noisy reporting that the
device is no longer available. Wifi is still available because iwlwifi
recovers, but it spews scary prints in the log.
Fix that by failing gracefully.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219597
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.d8d58146c829.I569ca15eaaa774d633038a749cc6ec7448419714@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Perhaps IWL_FW_CHECK() is a bit misnamed, but it just returns
the value of the inner condition. Therefore, the current code
skips the actual function when it has the BAID data and makes
it crash later when it doesn't. Fix the logic.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.9c0b84c44c3b.Ied236258854b149960eb357ec61bf3a572503fbc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When errors occur repeatedly, the driver shouldn't go into a
tight loop trying to reset the device. Implement the backoff
I had already defined IWL_TRANS_RESET_DELAY for, but clearly
forgotten the implementation of.
Fixes: 9a2f13c40c ("wifi: iwlwifi: implement reset escalation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.8816e299efa2.I82cde34e2345a2b33b1f03dbb040f5ad3439a5aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 switches between non-MLO and MLO it will recreate the
debugfs directories. This results in the add_if_debugfs handler being
called multiple times. As the convenience symlink is created in the mld
debugfs directory and not the vif, it will not be removed by mac80211
when this happens and still exists.
Add a check and only create the convenience symlink if we have not yet
done so.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.2490696f032a.I74319c7cf18f7e16a3d331cb96e38504b9fbab66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If starting the op mode failed, the opmode memory is being freed,
so trans->op_mode needs to be NULLified. Otherwise, trans will access
already freed memory.
Call iwl_trans_op_mode_leave in that case.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.3331d1686556.Ifaf15bdd8ef8c59e04effbd2e7aa0034b30eeacb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From the moment that we have ALIVE, we can receive notification that
are handled asynchronously.
Some notifications (for example iwl_rfi_support_notif) requires an
operational FW. So we need to make sure that they were handled in
iwl_op_mode_mld_start before we stop the FW. Flush the async_handlers_wk
there to achieve that.
Also, if loading the FW in op mode start failed, we need to cancel
these notifications, as they are from a dead FW.
More than that, not doing so can cause us to access freed memory
if async_handlers_wk is executed after ieee80211_free_hw is called.
Fix this by canceling all async notifications if a failure occurred in
init (after ALIVE).
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.1a8579662437.Ifd77d9c1a29fdd278b0a7bfc2709dd5d5e5efdb1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 75a3313f52.
The indication of the BW limitation in the sub-device ID is not applicable
for Killer devices. For those devices, bw_limit will hold a random value,
so a matching dev_info might not be found, which leads to a probe
failure.
Until it is properly fixed, revert this.
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220029
Fixes: 75a3313f52 ("wifi: iwlwifi: make no_160 more generic")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420115541.36dd3007151e.I66b6b78db09bfea12ae84dd85603cf1583271474@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The C sequence points are complicated things, and gcc-15 has apparently
added a warning for the case where an object is both used and modified
multiple times within the same sequence point.
That's a great warning.
Or rather, it would be a great warning, except gcc-15 seems to not
really be very exact about it, and doesn't notice that the modification
are to two entirely different members of the same object: the array
counter and the array entries.
So that seems kind of silly.
That said, the code that gcc complains about is unnecessarily
complicated, so moving the array counter update into a separate
statement seems like the most straightforward fix for these warnings:
drivers/net/wireless/intel/iwlwifi/mld/d3.c: In function ‘iwl_mld_set_netdetect_info’:
drivers/net/wireless/intel/iwlwifi/mld/d3.c:1102:66: error: operation on ‘netdetect_info->n_matches’ may be undefined [-Werror=sequence-point]
1102 | netdetect_info->matches[netdetect_info->n_matches++] = match;
| ~~~~~~~~~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mld/d3.c:1120:58: error: operation on ‘match->n_channels’ may be undefined [-Werror=sequence-point]
1120 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
side note: the code at that second warning is actively buggy, and only
works on little-endian machines that don't do strict alignment checks.
The code casts an array of integers into an array of unsigned long in
order to use our bitmap iterators. That happens to work fine on any
sane architecture, but it's still wrong.
This does *not* fix that more serious problem. This only splits the two
assignments into two statements and fixes the compiler warning. I need
to get rid of the new warnings in order to be able to actually do any
build testing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- iwlwifi: various build warning fixes (e.g. PM_SLEEP)
- iwlwifi: fix operation when FW reset handshake times out
- mac80211: drop pending frames on interface down
-----BEGIN PGP SIGNATURE-----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=FdK4
-----END PGP SIGNATURE-----
Merge tag 'wireless-2025-04-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a handful of fixes, notably
- iwlwifi: various build warning fixes (e.g. PM_SLEEP)
- iwlwifi: fix operation when FW reset handshake times out
- mac80211: drop pending frames on interface down
* tag 'wireless-2025-04-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
Revert "wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()"
wifi: iwlwifi: mld: Restart firmware on iwl_mld_no_wowlan_resume() error
wifi: iwlwifi: pcie: set state to no-FW before reset handshake
wifi: wl1251: fix memory leak in wl1251_tx_work
wifi: brcmfmac: fix memory leak in brcmf_get_module_param
wifi: iwlwifi: mld: silence uninitialized variable warning
wifi: mac80211: Purge vif txq in ieee80211_do_stop()
wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()
wifi: at76c50x: fix use after free access in at76_disconnect
wifi: add wireless list to MAINTAINERS
iwlwifi: mld: fix building with CONFIG_PM_SLEEP disabled
wifi: iwlwifi: mld: fix PM_SLEEP -Wundef warning
wifi: iwlwifi: mld: reduce scope for uninitialized variable
====================
Link: https://patch.msgid.link/20250411142354.24419-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reset handshake attempts to kill the firmware, and it'll go
into a pretty much dead state once we do that. However, if it
times out, then we'll attempt to dump the firmware to be able
to see why it didn't respond. During this dump, we cannot treat
it as if it was still running, since we just tried to kill it,
otherwise dumping will attempt to send a DBGC stop command. As
this command will time out, we'll go into a reset loop.
For now, fix this by setting the trans->state to say firmware
isn't running before doing the reset handshake. In the longer
term, we should clean up the way this state is handled.
It's not entirely clear but it seems likely that this issue was
introduced by my rework of the error handling, prior to that it
would've been synchronous at that point and (I think) not have
attempted to reset since it was already doing down.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219967
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219968
Fixes: 7391b2a4f7 ("wifi: iwlwifi: rework firmware error handling")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250411104054.63aa4f56894d.Ife70cfe997db03f0d07fdef2b164695739a05a63@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The newly added driver causes multiple build problems when CONFIG_PM_SLEEP is
disabled:
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1982:12: error: 'iwl_mld_resume' defined but not used [-Werror=unused-function]
1982 | static int iwl_mld_resume(struct ieee80211_hw *hw)
| ^~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1960:1: error: 'iwl_mld_suspend' defined but not used [-Werror=unused-function]
1960 | iwl_mld_suspend(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan)
| ^~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1946:13: error: 'iwl_mld_set_wakeup' defined but not used [-Werror=unused-function]
1946 | static void iwl_mld_set_wakeup(struct ieee80211_hw *hw, bool enabled)
| ^~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c: In function 'iwl_mld_mac80211_start':
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:504:20: error: 'ret' is used uninitialized [-Werror=uninitialized]
504 | if (!in_d3 || ret) {
| ^~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:478:13: note: 'ret' was declared here
478 | int ret;
| ^~~
Hide the unused functions and make sure the 'ret' variable is not used
before the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250325084340.378724-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Config symbols are not defined if turned off, so need to
use #ifdef, not #if.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Yedidya Ben Shimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250401064530.612020bcdaad.I4e885e6646576e29fb236250a1b5038d3f14b08e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After resuming from D3, keeping the connection or disconnecting
isn't relevant for the case of netdetect.
Reduce the scope of the keep_connection indicator to wowlan only.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250401064530.769f76a9ad6e.I69e8f194997eb3a20e40d27fdc31002d5753d905@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create a new tagged `struct iwl_tx_cmd_hdr`. This structure
groups together all the members of the flexible `struct iwl_tx_cmd`
except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct iwl_tx_cmd` to `struct iwl_tx_cmd_hdr`.
We also want to ensure that when new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct iwl_tx_cmd_hdr`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/intel/iwlwifi/dvm/commands.h:2315:27: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlwifi/dvm/commands.h:2426:27: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/Zr5QR03+wyw571zd@elsanto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Roll-back to use iwlmvm for those devices. iwlmld will support wifi7
capable devices only. The firmware for the non-wifi7 capable will soon
be frozen and we don't want iwlmld to have to support devices that will
require the old APIs.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250318103019.df6df96df826.I0020ca9f6c6c928caa78721666df131a692c6186@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mld_remove_link removes the link from both the FW and from the
driver.
If removing it from the FW failed, we assume that the FW is
dead anyway and remove it from the driver as well.
On the other hand, we still return an error value, indicating the caller
(i.e. mac80211) that the link couldn't be removed - while it was
actually removed.
Later, mac80211 might tell the driver again to remove that link,
and then the driver will warn that it doesn't exist.
Fix this by making iwl_mld_remove_link a void function.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.16fe6ebae412.If5371ff7e096b7078ff9e98ff0e72010cd1f076d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently iwlmld_kunit_add_chanctx receives a band, picks a predefined
static chandef, and creates the chanctx from it.
Change it to receive a bandwidth as well. Otherwise, the bandwidth in
the chanctx/phy will be different than what test specified in the
iwl_mld_kunit_link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.85a1285d34cd.Ia71cdcd4241fe73501bc93e3cb2c6bb3f631b9ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow setting up association/EMLSR states with more flexibility,
change the relevant functions to receive a new struct, iwl_mld_kunit_link,
which will contain all the link parameters (for now just link id, band
and bandwidth).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f336491ccc4e.I6b727765eb394a3dbb78cea71e356be1bdc4a17c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow EMLSR if the bandwidths of the links are unequal if one of the
following conditions is true:
1. in low latency mode
2. bandwidth of the secondary link is greater than the bandwidth of the
primary
3. the primary link is active and is loaded enough to justify EMLSR
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.150c330711c4.Ifd72d2e076783991852a7f1756948b4f0efb9fea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We exit EMLSR mode if the FW requested to do so.
To prevent repeated toggling of the EMLSR mode (frequent entry and
exit), add this exit reason to the EMLSR prevention mechanism.
This mechanism avoids re-entering EMLSR for a certain period of time
after multiple exits caused by the same reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f0e74a7f99af.I447c8788afba85a2a5040ae2c1213b6e05ec14f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel load logic moves from the FW to the driver.
- Implement the logic: allow EMLSR only if the candidate primary link is
active and if its average channel load exceeds the threshold.
- Remove IWL_MLD_EMLSR_BLOCKED_FW. Instead, treat ESR_RECOMMEND_LEAVE in
the EMLSR_RECOMMENDATION notif as an EXIT reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.6729a8d67815.Iab39bf0982d8cdbb0db701d31854101c2fcf3b64@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add debugfs file in mld to retrieve TAS status per radio, TAS block list,
current mcc, OEM name and OEM allowed list. This will add ability to get
TAS status to user application via debugfs and required for debugging.
Add the required API definitions and some debug host command utils.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.66524c6ea198.I1625135284fc075148a55dd9ac629e94ca881fe4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro is intended to call
read/write handlers with the wiphy lock held. However, the current
implementation uses the MLD_DEBUGFS_READ_WRAPPER macro, which does
not hold the wiphy lock during read operations. This fix updates
the WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro to use the
WIPHY_DEBUGFS_READ_WRAPPER_MLD macro instead, ensuring that the
wiphy lock is held during both read and write operations.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.2001d2335e9d.I607a8bd12efc6d1190cef1fca44279dbdd2756ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduced the WIPHY_DEBUGFS_READ_FILE_OPS_MLD macro to enable reading
data from the driver while holding the wiphy lock.
This will enable read operations with wiphy locked.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.b0ddb6b0a144.I1fab63f2c6f52fea61cc5d7b27775aed58adfd8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Renamed the macro WIPHY_DEBUGFS_HANDLER_WRAPPER to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER to better reflect its purpose as a
write handler.
Additionally, updated the corresponding macro
WIPHY_DEBUGFS_HANDLER_WRAPPER_MLD to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER_MLD for consistency.
This change does not alter the functionality but enhances the
maintainability of the code.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.bb8a1d7907c8.I53325f2f37ccaad2b212d35d10616e06c1555e48@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few conflicts between the work that went
into wireless and that's here now, resolve them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pointers declared with the __free(kfree) attribute need to be initialized
because they will be passed to kfree() on every return path. There are
two return statement before the "cmd" pointer is initialized so this
leads to an uninitialized variable bug.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/f7c17a7f-f173-43bf-bc39-316b8adde349@stanley.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, we don't select a link that wasn't heared in the last 5
seconds.
But if the link started to suffer from missed beacons more recent than
that, we might select this link even we really shouldn't,
leading to a disconnection instead of a link switch.
Fix this by checking if a link was heared in the last MLO scan,
if not - don't include it in the link selection.
Since we do an MLO scan on missed beacons, we will not hear that link in
that scan, and won't select it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.8f950497219e.I51306021fe9231a8184e89c23707be47d3c05241@changeid
[replace cast with ULL constant]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the RSSI is dropping to below the threshold, we need to do a MLO
scan to try select a better link.
This is true also if the connection doesn't have EMLSR capability,
and also if we are in EMLSR.
Fix the logic to always check the RSSI (and do a MLO scan if needed).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.a31b95888244.If6dca30d657658fa902b19e07b6fbc86c48d69cb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to the requirements, if the last scan isn't older than 20
seconds, we can use its results and do the link selection without
scanning before.
But this applies only when trying to get back to EMLSR, not if the link
has bad RSSI/missed beacons.
Since an MLO scan is cheap anyway, and results from 20 seconds before
are really old, always scan before links switching.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.a4c96e5c49d4.Ie55697af49435c2c45dccf7c607de5857b370f7a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the setting of the A-MSDU maximal lengths as follows:
- Move the setting of the maximal A-MSDU length in case of HT from TLC
logic to the station logic as it is not related to TLC.
- As long as the station is not associated, set RC A-MSDU maximal
lengths to 1, to prevent iwlmld and mac80211 from building A-MSDUs.
- Update the RC and the TID specific A-MSDU maximal lengths based on
the FW TLC notifications.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.afc842633002.I68153b6b0c5d976f2c7525009631f8fa28e9987c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On station interfaces we don't only have the AP STA, but also
TDLS stations. Don't try to remove AP keys for them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.f06a4d6eed2b.Icd20af668a22bfae5328eb0ea00ce10a72ce3539@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the iwl_mld_get_chandef_from_chanctx() logic, even after
the OMI handshake to reduce bandwidth the driver wouldn't apply
that to the PHY context, since it always uses the normal, not
the reduced, configuration on 6 GHz (not strictly always, but
OMI will only apply if the original bandwidth is > 80 MHz.) Fix
this by making that selection contingent on AP mode. Refactor
the code a bit to also make it clearer why the min_def isn't
used in that case (for FILS.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.2706cbd0b100.Ic34636b1aee81a140eb690fca8139909a58f8e8b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used ieee80211_iterate_active_interfaces instead of
ieee80211_iterate_active_interfaces_mtx, which is the one to use when
the wiphy lock is held.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20250309073442.925cdca61ed0.I34f5c52d27414cb4c301bbd24df7c3530a43fa1d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since iwlmld claims wiphys to be self-managed, it needs to
have a regdomain registered before the wiphy is registered
to avoid issues when trying to get the regdomain, e.g. via
"iw phy phy0 reg get".
Move the initialization early, on every FW start not just
when starting to really operate it. This also requires the
self-managed flag to be set early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.10ab8fed94e9.I7c8dee3d14c7427a56882739f82546c6492f3b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code was calling ieee80211_iterate_interfaces, however that
takes a lock of iflist_mtx, which must not be taken recursively. Fix
this by using the appropriate _mtx version that asserts that the wiphy
mutex is already held.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.6ce298d6a44f.Ibc862dfdd6cb2da63781c791b9dc601bd5ce4bdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Change reasons enum to a bitmask and rename it
- Don't use 'else if' so all reasons will be set in the reasons bitmask
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.0a3b2f88fbbf.I0152bc39e828488451e85135feb044ce1f7a85d3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For each channel context, track the avarage channel load by others in the
driver specific phy data, to be used by EMLSR.
Due to FW limitations, this value is incorrect in EMLSR, so it is
shouldn't be used in EMLSR.
On EMLSR exit, clear it so the wrong value won't be used.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.dd443fc5b178.I68b2fed197aae14888159b7a73bf40c2f346f41f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user disables power save of a vif that didn't have it enabled
(for example before association), mac80211 will not notify the driver
with BSS_CHANGED_PS. This will cause the driver to not update the
device-level power save to disabled.
Fix this by checking the vif's power save status upon authorization, and
stop considering the vif's power save status on disassociation.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.1cdeb78b19ba.I58fe02c062524029071b04b093a1b09c5e46f4ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running secured ranging and the initiator is associated with
the responder, the TK was not set in the range request command.
Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.603dc31579d9.Icd19d797e56483c08dd22c55b96fee481c4d2f3d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.ba3d90b22c25.I9332506af1997faefcf0bdb51d98d5e874051722@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Corrected the bit size calculation in the for_each_set_bit macro in
the iwl_dbgfs_tas_get_status_read(). The previous implementation used
sizeof(dyn_status), which only accounts for the number of bytes.
This has been updated to TAS_DYNA_STATUS_MAX to ensure the loop iterates
over the correct number of valid bits in dyn_status.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.65d373e4a10e.If2cea63035333b07849e5a2c2a4f5dc5c5239595@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW is now responsible of determining the SMPS mode.
If the user disabled power save in a certain vif, we send the vif-level
power command to clear out the POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK bit
for that vif.
But erroneously, the FW checks DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK in
the device-level command to determine the SMPS mode.
To W/A this, send also the device-level command when the power save of a
vif changes, and disable power save if there is any vif that has power
save disabled.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.7bf205efa027.I2c793ff1fc2a6779a95faaee1ded348100fd97f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The order of actions taken for debug was implemented incorrectly.
Now we implemented the dump split and do the FW reset only in the
middle of the dump (rather than the FW killing itself on error.)
As a result, some of the actions taken when applying the config
will now crash the device, so we need to fix the order.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.6de7fa8e63ed.I40632c48e2a67a8aca05def572a934b88ce7934b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new reason is added to the iwl_tas_statically_disabled_reason enum
and the corresponding message is updated in the
iwl_dbgfs_tas_get_status_read().
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.5e1272ef3508.I24f668ae716bee20cba15fdc73c3363693bbaf73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removed mvm prefix from the following structures and enum names:
1. struct iwl_tas_status_per_mac
2. struct iwl_tas_status_resp
3. enum iwl_tas_dyna_status
4. enum iwl_tas_statically_disabled_reason
As these structures and enums are not specific to mvm.
Replaced TAS_LMAC_BAND_LB, TAS_LMAC_BAND_HB, and TAS_LMAC_BAND_UHB macros
with a generic BAND macro, as these macros are not specific to TAS.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.59144bee9987.Ic2678dcb5afdacc2ca234d4aa4901e7e1f6e8dbb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This UEFI variable name was badly named. Fix its name and also use the
right GUID to find it: we need to use the BT_WIFI (a.k.a. Common) GUID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231426.78c998d0fa71.I2bc9d72c1dc2c4d7028f0265634a940c2fadbbb5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the restart work happens to run after the opmode left
(i.e. called iwl_trans_op_mode_leave), then the opmode memory (including
its mutex) is likely to be freed already, and trans->opmode is NULL.
Although the hw is stopped in that stage, which means that this restart
got aborted (i.e. STATUS_RESET_PENDING will be cleared),
it still can access trans->opmode (NULL pointer dereference)
or the opmodes memory (which is freed).
Fix this by canceling the restart wk in iwl_trans_op_mode_leave.
Also make sure that the restart wk is really aborted.
Fixes: 7391b2a4f7 ("wifi: iwlwifi: rework firmware error handling")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250306122425.801301ba1b8b.I6f6143f550b6335b699920c5d4b2b78449607a96@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When MSI-X is not enabled, we mask all the interrupts in the interrupt
handler and re-enable them when the interrupt thread runs. If
STATUS_INT_ENABLED is not set, we won't re-enable in the thread.
In order to get the ALIVE interrupt, we allow the ALIVE interrupt
itself, and RX as well in order to receive the ALIVE notification (which
is received as an RX from the firmware.
The problem is that STATUS_INT_ENABLED is clear until the op_mode calls
trans_fw_alive which means that until trans_fw_alive is called, any
notification from the firmware will not be received.
This became a problem when we inserted the pnvm_load exactly between the
ALIVE and trans_fw_alive.
Fix that by calling trans_fw_alive before loading the PNVM. This will
allow to get the notification from the firmware about PNVM load being
complete and continue the flow normally.
This didn't happen on MSI-X because we don't disable the interrupts in
the ISR when MSI-X is available.
The error in the log looks like this:
iwlwifi 0000:00:03.0: Timeout waiting for PNVM load!
iwlwifi 0000:00:03.0: Failed to start RT ucode: -110
iwlwifi 0000:00:03.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
Fixes: 70d3ca86b0 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.0f2cf207aae1.I025d8f724b44f52eadf6c19069352eb9275613a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The allocation of the scatter gather data structure should be done
based on the number of memory chunks that need to be mapped, and it
is not dependent on the overall payload length. Fix it.
In addition, as the skb_to_sgvec() function returns an 'int' do not
assign it to an 'unsigned int' as otherwise the error check would be
useless.
Fixes: 7f5e3038f0 ("wifi: iwlwifi: map entire SKB when sending AMSDUs")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.8c0e23a3d583.I3cb4d6768c9d28ce3da6cd0a6c65466176cfc1ee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My previous patch caused a slight code size increase when DEBUG_FS is disabled,
as Stanislaw Gruszka pointed out.
Fix this with an added IS_ENABLED() check.
Fixes: cf6b9ba172 ("wifi: iwlegacy: don't warn for unused variables with DEBUG_FS=n")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250304144210.997531-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e4 ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
iwlwifi is the driver of all Intel wifi devices since 2008.
Since then, the hardware has changed a lot, but the firmware
API has changed even more. The need to keep one driver that
supports all those different APIs led us to introduce a new
architecture circa 2012 which allowed us to keep the same
interface to the hardware (DMAs, Tx queues, etc...) with a
new layer to implement the mid-layer between mac80211 and
the firmware. The first component is called the 'transport'
and the latter is called 'operation_mode' a.k.a op_mode.
In 2013 we took advantage of the new architecture to
introduce iwlmvm which allowed us to implement the, then,
new firmware API. This op_mode supports 7260 and up, those
devices supports support at least VHT.
Since then, wifi evolved and so did the firmware. It became
much bigger and took a lot of functionality from the driver.
It became increasingly hard to keep the same op_mode for the
newest devices and we experienced frequent regressions on
older devices. In order to avoid those regressions and keep
the code maintainable, we decided it was about time to start
a new op_mode.
iwlmld is a new op_mode that supports BE200 or newer if the
firmware being used is 97.ucode or newer. If the user has
an older devices or BE200 with .96.ucode, iwlmvm will be
loaded. Of course, this op_mode selection is seamless.
All the features supported in iwlmvm are supported in
iwlmld besides a few seldom used use cases: injection and
Hotspot 2.0. Those are under work.
A few points about the implementation:
* iwlmld doesn't have any mutexes, it relies on the
wiphy_lock
* iwlmld is more "resource oriented": stations, links and
interfaces are allocated and freed only after all the
relevant flows are completed.
* Firmware notifications' sizes are validated in a more
structured way.
We would love to see this new op_mode merged in 6.15. The
firmware for this new driver (.97.ucode) is not yet publicly
available but it'll be sent very soon.
People eager to get an early version of this firmware can
contact Emmanuel at:
emmanuel.grumbach@intel.com
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Co-developed-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Co-developed-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/linux-wireless/20250216094321.537988-1-miriam.rachel.korenblit@intel.com/
[fix Kconfig, fix api/phy.h includes, SPDX tag and coding
style issues, duplicated includes per 0-day robot]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This file should never have been part of the commit, remove it.
Fixes: af3be90884 ("wifi: iwlwifi: support ROC version 6")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow to read the table once, and not any time the command is
sent. The actual use of this will be in a later patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.61801b78a2cb.I710a766888f370a75b47116fec29d41c106b13ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will now be called from another opmode we are writing.
iwl_fill_lari_config will only be used for the older ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.9bb7fbc592a6.I8850691eac7c8471257f3031e8c05905afc72f70@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the BIOS allows it, instruct the firmware to use the external 32
KHz clock.
The op mode specific implementation (i.e. reading the BIOS table) will
come in a later patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.9aae3f74fee0.I25ae45ef02b9ea387b512f974c1f3e5367a537e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the version suffix from the latest version of the range
request command structs and the range response notification structs.
In addition, don't use MVM in the API file as it is not MVM specific.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.294b7109e0be.I229ceef5933e825815d84c33855cadd62687ee04@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reference to il_rate_mcs is inside of an #ifdef, causing a W=1 warning:
drivers/net/wireless/intel/iwlegacy/4965-rs.c:189:38: error: unused variable 'il_rate_mcs' [-Werror,-Wunused-const-variable]
static const struct il_rate_mcs_info il_rate_mcs[RATE_COUNT] = {
Replace the #ifdef with a PTR_IF() for better compile time analysis.
The dead code will still get eliminated, but the warning goes away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250225145359.1126786-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TSO preparation assumed that the skb head contained the headers
while the rest of the data was in the fragments. Since this is not
always true, e.g., it is possible that the data was linearised, modify
the TSO preparation to start the data processing after the network
headers.
Fixes: 7f5e3038f0 ("wifi: iwlwifi: map entire SKB when sending AMSDUs")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.75769a4769bf.Iaf79e8538093cdf8c446c292cc96164ad6498f61@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When failing to prepare the data needed for A-MSDU transmission, the memory
allocated for the TSO management was not freed. Fix it.
Fixes: 7f5e3038f0 ("wifi: iwlwifi: map entire SKB when sending AMSDUs")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.bc27fad9b3d5.Ibf43dd18fb652b1a59061204e081f11c9fa34a3f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no guarantee here that the file is always with a
NUL-termination, so reading the string may read beyond the
end of the TLV. If that's the last TLV in the file, it can
perhaps even read beyond the end of the file buffer.
Fix that by limiting the print format to the size of the
buffer we have.
Fixes: aee1b6385e ("iwlwifi: support fseq tlv and print fseq version")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.cb5f9d0c2f5d.Idec695d53c6c2234aade306f7647b576c7e3d928@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware uses the newer version of the API in recent devices. For
older devices, we translate the rate to the new format.
Don't parse the rate with old parsing macros.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.13d70cdcbb4e.Ic92193bce4013b70a823cfef250ee79c16cf7c17@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not really a firmware error. We need to reload the firmware, but
this doesn't mean that we should consider this as a firmware error.
When the firmware was restarted upon resume, this wasn't felt by the
driver. Now that we keep the firmware running during suspend even if we
don't have wowlan, this started to pop-up.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.a10463a40318.I14131781c3124b58e60e1f5e9d793a2bc88b464c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware fails to start the session protection, then we
do call iwl_mvm_roc_finished() here, but that won't do anything
at all because IWL_MVM_STATUS_ROC_P2P_RUNNING was never set.
Set IWL_MVM_STATUS_ROC_P2P_RUNNING in the failure/stop path.
If it started successfully before, it's already set, so that
doesn't matter, and if it didn't start it needs to be set to
clean up.
Not doing so will lead to a WARN_ON() later on a fresh remain-
on-channel, since the link is already active when activated as
it was never deactivated.
Fixes: 35c1bbd93c ("wifi: iwlwifi: mvm: remove IWL_MVM_STATUS_NEED_FLUSH_P2P")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.0fe36c291068.I67f5dac742170dd937f11e4d4f937f45f71b7cb4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_fwrt_read_err_table can return true also when it failed to read
the memory. In this case, err_id argument is not initialized,
but the callers are still using it.
Simply initialize it to 0. If the error table was read successfully it'll
be overridden.
Fixes: 43e0b2ada5 ("wifi: iwlwifi: fw: add an error table status getter")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250209143303.37cdbba4eb56.I95fe9bd95303b8179f946766558a9f15f4fe254c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware dumps can be pretty big, and since we use single
pages for each SG table entry, even the table itself may end
up being an order-5 allocation. Build chained tables so that
we need not allocate a higher-order table here.
This could be improved and cleaned up, e.g. by using the SG
pool code or simply kvmalloc(), but all of that would require
also updating the devcoredump first since that frees it all,
so we need to be more careful. SG pool might also run against
the CONFIG_ARCH_NO_SG_CHAIN limitation, which is irrelevant
here.
Also use _devcd_free_sgtable() for the error paths now, much
simpler especially since it's in two places now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.697c7a465ac9.Iea982df46b5c075bfb77ade36f187d99a70c63db@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to hardware design constraints, a reset handshake may be
necessary even when the firmware has already crashed, with
the dump descriptions indicating which parts should be done
before/after the handshake, if needed. Implement that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.9296e3113d42.Ifb32703fd06a644d08a86b7af1b990738e3c8134@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a bit that tells the firmware to wait for the
PHY_CONFIGURATION_CMD before completing its init sequence.
Clarify this in the comment.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.097510347ae2.Ica00b4b30163a21bf993fa968dd406ee4023fc9e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll have devices that are EHT capable but don't support 320 MHz and
those devices look like the 320 MHz capable devices, but have distinct
subsystem ID.
We already had the same type of differentiation for HE devices that
support 160 MHz or not.
Enhance that mechanism and now the _IWL_DEV_INFO macro gets an
indication whether the bandwidth should be limited for that specific
device.
The subsystem ID gives a binary answer about the bandwidth limitation
and iwl_pci_find_dev_info() compares this to the list of _IWL_DEV_INFO
entries.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.1ba406c538a5.I6e24123f60a764aedfeaaac8768c26e136c320cf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Re-probing if we had 2 firmware crash within 3 minutes is really too
aggressive. Drastically reduce the threshold to 7 seconds.
After 7 seconds, a new firmware crash will be considered "new" and not
cause a PCI re-probe.
This allows to pass tests that cause a firmware crash every 10 seconds
and expect to see no impact on the traffic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.38f912b047f4.I03f0c10ae9e7ecea639431f3e089b757cc8a4347@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As MLO link configuration is supported by mac80211, indicate
support for MLO link reconfiguration in station mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
----------------
depends on "wifi: ieee80211: Add some missing MLO related definitions"
Link: https://patch.msgid.link/20250205145347.92d19705d2b9.Id07fa3ebad6bc23ecf6e91868f67150ce70f47b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're adding a new IWLMLD opmode for just BZ and later
devices. If that's enabled but IWLMVM isn't, the build
fails because 22000 family configs aren't built but BZ
and later refer to it. Rather than trying to make some
new file to build it in all cases, just copy the small
struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.1d6186c23bee.I3c61a6c9e0db3ba6eea4dac63e1547945ad01703@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Despite not being able to sustain the full 320 MHz throughput
even at MCS 9, enable 320 MHz on slow PCIe links. This may in
some cases result in frames being dropped (on the air) by the
firmware if they cannot be delivered to the host, but it can
still be better to use 320 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.1e5356a3b124.I1224023721aaeff8ebcaa47dff88613c7fd0533a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reprobe, the sw state is being destroyd, and so is the
connection. When the peer STA is being removed, the opmode sends a
command to flush the TXQs of the STA and uses iwl_trans_wait_txq_empty.
This one warns if the FW is not alive, but it really shouldn't if
there is a FW error - and return silently instead, just like we do when
sending a hcmd.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250205145347.76425b10e5a0.I3bf0de2eb090a8b94c4e36d93dd91df61fadb808@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Created a common function iwl_add_mcc_to_tas_block_list() to handle the
operations previously performed by iwl_mld_add_to_tas_block_list() and
iwl_mvm_add_to_tas_block_list(). moved this new function to regulatory.c
to better reflect its purpose and improve code organization.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.157d26fb7f02.I87e20e967835bc895be390daf1c6637e20b52aae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Renamed iwl_mvm_eval_dsm_rfi() to iwl_rfi_is_enabled_in_bios() to better
reflect the function's operation. Additionally, moved the function to the
regulatory.c file for better organization. optimize local variable
usage in it.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.b7ac9d05234e.Ieb623d7e8dca6bb6a5733682b31e4ff1e39373f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The last use of iwl_ax204_name[], iwl_ax221_name[] and iwl_cfg_so_a0_ms_a0
was removed by
commit f473a7fd6d ("wifi: iwlwifi: remove devices that never came out")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-7-linux@treblig.org
iwl_bz_name[] has been unused since the resent
commit 6795a37161 ("wifi: iwlwifi: Print a specific device name.")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-6-linux@treblig.org
iwl_mvm_ftm_add_pasn_sta() was added in 2020 by
commit 0739a7d70e ("iwlwifi: mvm: initiator: add option for adding a
PASN responder")
but hasn't been used.
Remove it.
That was the only caller of iwl_mvm_ftm_remove_pasn_sta().
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-5-linux@treblig.org
iwl_mvm_ftm_respoder_add_pasn_sta() and
iwl_mvm_ftm_resp_remove_pasn_sta() were added in 2020 by
commit be82ecd3a5 ("iwlwifi: mvm: add an option to add PASN station")
but have remained unused.
Remove them.
After that removal iwl_mvm_add_pasn_sta() is now unused.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-4-linux@treblig.org
iwl_mvm_rx_missed_vap_notif() was added in 2019 by
commit 449a29d0fe ("iwlwifi: mvm: add notification for missed VAP")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-3-linux@treblig.org
iwl_rx_ant_restriction() was added in 2009 by
commit 46f9381aa3 ("iwlwifi: Thermal Throttling Management - part 2")
but never used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241223013202.340180-2-linux@treblig.org
libipw_rx_any() was added in 2006 by commit 1a995b45a5 ("[PATCH]
ieee80211_rx_any: filter out packets, call ieee80211_rx or ieee80211_rx_mgt")
as ieee80211_rx_any but is currently unused and I can't find any sign it was
used under either name.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250122022240.456198-1-linux@treblig.org
Extend TAS_CONFIG to send exact data read from bios to firmware
without filtering/altering bios data. This enables driver becoming
purely a pipe for TAS features.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.f46d58e7cfd1.Ifd81e632fa3e7039b8d139ee0d1c24e09669dff5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All newer devices now require PNVM files, so don't list them
separately but simply generate the relevant MODULE_FIRMWARE()
declarations together. This simplifies the code and adds a
large number of missing PVNM declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.302e521e08e9.I782513432d3dcbf801e8262522ded95302548e1c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two cases in which the min_def isn't used:
a) if FILS will be enabled
b) if FTM responder is enabled
Both of these apply to AP mode only, but for FILS we're
not checking that right now. Change the code to iterate
the interfaces and links using the channel context, and
check for AP mode for both, not just for FTM responder.
In the case of iwl_mvm_enable_fils() this might also fix
an issue where FILS is enabled for an IBSS network that
happens to be started on 6 GHz, though that's not very
likely to be possible due to regulatory.
However for RX OMI bandwidth reduction the driver needs
to use the min_def in client mode as well, in order to
actually reduce bandwidth when it requested that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.7b91025e103d.I4c99c03fd32363d574ab5e34798b6099401f0729@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the normal reset methods don't work well, attempt to
escalate to ever increasing methods. TOP reset will only
be available for SC (and presumably higher) devices, and
still needs to be filled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.804e005403d8.I9558f09cd68eec16b02373b1e47adafd28fdffa3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TOP is a shared (between BT and WiFi) hardware component,
and if it has an error we need to reset the whole device, i.e.
both BT and WiFi. This is achieved by calling a specific ACPI
DSM (device-specific method) with the right arguments before
doing a reset via the object referenced by _PRR.
Since this is needed here, but a function reset will always do
better than just re-enumerating the bus in case of errors, we
can always try to at least do a function reset and do the full
product reset only when needed for TOP errors.
Also, for some Bz and Sc devices where BT is PCIe/IOSF as well,
find the BT device and unbind that device as well so the BT
driver can recover from the reset that's going to happen,
rather than having to somehow detect that the device was reset.
Also add - currently unused - the function reset mode, this is
going to get used in the upcoming escalation model.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.5b0f846d3e13.Ia14ccac38ac3d48adf5f341b17c7e34ccc41c065@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to know whether or not a product reset can safely
be done (without risking locking up the system completely),
check for ME presence with the known methods.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.0ac9173f1f37.Id83b80b61548b8f4f01e96a356dafe063543c4ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_ssid_exist() seems to check if a given ssid/ssid_len already
exists in a given array ssid_list.
Correctly compare the ssid to the SSID of each array element
(with a matching SSID length) to better remove duplicates.
Signed-off-by: Bjoern A. Zeeb <bz@FreeBSD.org>
Sponsored by: The FreeBSD Foundation
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Link: https://patch.msgid.link/20241229164246.4471cd3d8dba.Iab8409b22bf6f01d05571ecef1e97dd3c8b1cc75@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Smatch reported that we dereference the data pointer to calculate the
expected length before we check it's not NULL. While this is true (and
hence needs to be fixed), this will never happen because the data
pointer comes from struct iwl_rx_packet object which has the following
layout:
struct iwl_rx_packet {
__le32 len_n_flags;
struct iwl_cmd_header hdr;
u8 data[];
} __packed;
So, if the pointer to iwl_rx_packet is valid, data will be valid as
well.
Remove the NULL pointer check on 'data' to avoid confusing smatch.
Also remove the check from similar functions in the same flow that were
cargo cult copy-pasted.
Fixes: 4635e6eaa0 ("wifi: iwlwifi: mvm: support new versions of the wowlan APIs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202411210812.0eLaonw3-lkp@intel.com/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241229164246.c8ce6e041e4b.I4dc19289e3f3807386768c846e08be3ea322cd15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should be comparing the AP STA, not the deflink firmware STA
ID. Correct the implementation so that statistics can be requested
for the AP, but not for other stations that may end up with the
firmware STA ID matching 0 in the deflink, or so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241229164246.08b05aca37cf.Iba1a6a637a758691f710dc4f3f03bd1d960fb087@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When handling TX_CMD notification, for mgmt frames tid is equal
to IWL_MAX_TID_COUNT, so with the current logic we'll count
that as MPDU, fix that.
Fixes: ec0d43d26f ("wifi: iwlwifi: mvm: Activate EMLSR based on traffic volume")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241229164246.80b119bb5d08.I31b1e8ba25cce15819225e5ac80332e4eaa20c13@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The API isn't really MVM specific, it's just the firmware
API. Remove the "MVM_" from the name here as well, as we've
already done in many other places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241229164246.66e17791c392.I6998e263973c26c1e22b4f470b974a519011b29a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When iterating over the links of a vif, we need to make sure that the
pointer is valid (in other words - that the link exists) before
dereferncing it.
Use for_each_vif_active_link that also does the check.
Fixes: 2b7ee1a10a ("wifi: iwlwiif: mvm: handle the new BT notif")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241229164246.31d41f7d3eab.I7fb7036a0b187c1636b01970207259cb2327952c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My recent restart related work has made this race more likely
to happen and we've now noticed it, but it seems that it was
always possible. The race is that the add stream work can be
scheduled just before a restart is scheduled and then execute
before the restart, accessing the device while it's doing the
restart and not accessible.
To fix this, check if the device is restarting and abort the
work in that case. Reschedule it after the restart as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.9c30af039b4d.I1a32936776f8ba5e83dda0a68ffc2722d9d37950@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By convention the newest version of a command/notification structure is
named with out the _ver_# suffix. Apply to stored_beacon_notif.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.e2140aa3c65b.Ie851bdda6df02dcc352bf765a3ec6bdac45c65a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A caller of iwl_acpi_get_dsm_object must free the returned object.
iwl_acpi_get_dsm_integer returns immediately without freeing
it if the expected size is more than 8 bytes. Fix that.
Note that with the current code this will never happen, since the caller
of iwl_acpi_get_dsm_integer already checks that the expected size if
either 1 or 4 bytes, so it can't exceed 8 bytes.
While at it, print the DSM value instead of the return value, as this
was the intention in the first place.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.bf61eaab99f8.Ibdc5df02f885208c222456d42c889c43b7e3b2f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Usually each struct that represent an API needs to have a comment
specifying all the versions of the API that this struct corresponds to.
iwl_tx_cmd_gen3 was long supporting also version 10. Say that.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241228223206.83d681dc9cf7.I355270fb20b23978d9402cb70caf52a0108b8cd4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The register 0x000 is now really boot control, and some
of the old bit names were (even for old hardware) not
reflecting the names on the hardware side; rename them
in the driver to align the naming.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.6f25be160619.I3ffc9601e99dc414a9ae54a0d90c9d20c0253da5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since iwl_fw_error_collect() is now always called with the sync
argument set to true, to collect data synchronously, remove the
argument from it entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.08f515513e88.I780a557743ca7f029f46a1cc75d0799542e39d83@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to later add the ability to do deeper resets of the
device when it crashes, first restructure the firmware error
handling. Instead of having just a single nic_error() method
that handles all, split it:
- nic_error() just handles and prints the error itself,
- dump_error() synchronously creates an error dump, and
- sw_reset() will be called to request doing a SW reset.
This changes the architecture so that the transport is now
responsible for deciding how to do the reset, and therefore
the handling of reprobe if error occurs during reconfig
moves there, which necessitates adding a method there that
notifies the transport that the recovery was completed.
Actually introducing the model under which deeper resets can
be done will be in future patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.6d4f741ae907.I96a9243e7877808ed6d1bff6967c15d6c24882f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
