We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 626 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xe4
As the Renesas SuperH Ethernet driver already calls phy_{stop,start}()
in its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/c6e1331b9bef61225fa4c09db3ba3e2e7214ba2d.1663598886.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EMAC IP found on RZ/G2L Gb ethernet supports MII interface.
This patch adds support for selecting MII interface mode.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20220914192604.265859-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the Renesas Ethernet AVB (EtherAVB-IF) blocks on R-Car
Gen4 SoCs (e.g. R-Car V4H) by matching on a family-specific compatible
value.
These are treated the same as EtherAVB on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/2ee968890feba777e627d781128b074b2c43cddb.1662718171.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/V2M Ethernet is very similar to R-Car Gen3 Ethernet-AVB, though
some small parts are the same as R-Car Gen2.
Other differences to R-Car Gen3 and Gen2 are:
* It has separate data (DI), error (Line 1) and management (Line 2) irqs
rather than one irq for all three.
* Instead of using the High-speed peripheral bus clock for gPTP, it has a
separate gPTP reference clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/V2M has a separate gPTP reference clock that is used when the
AVB-DMAC Mode Register (CCC) gPTP Clock Select (CSEL) bits are
set to "01: High-speed peripheral bus clock".
Therefore, add a feature that allows this clock to be used for
gPTP.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car has a combined interrupt line, ch22 = Line0_DiA | Line1_A | Line2_A.
RZ/V2M has separate interrupt lines for each of these, so add a feature
that allows the driver to get these interrupts and call the common handler.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the HW has a single interrupt, the driver uses the
GIC, TIC, RIC0 registers to enable and disable interrupts.
When the HW has multiple interrupts, it uses the GIE, GID, TIE, TID,
RIE0, RID0 registers.
However, other devices, e.g. RZ/V2M, have multiple irqs and only have
the GIC, TIC, RIC0 registers.
Therefore, split this into a separate feature.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
'max_rx_len' can be up to GBETH_RX_BUFF_MAX (i.e. 8192) (see
'gbeth_hw_info').
The default value of 'num_rx_ring' can be BE_RX_RING_SIZE (i.e. 1024).
So this loop can allocate 8 Mo of memory.
Previous memory allocations in this function already use GFP_KERNEL, so
use __netdev_alloc_skb() and an explicit GFP_KERNEL instead of a
implicit GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_{suspend|resume}() initialize their local variable 'ret' to 0 but
this value is never really used, thus we can kill those intializers...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/f09d7c64-4a2b-6973-09a4-10d759ed0df4@omp.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() always returns 0, hence the check in sh_eth_wol_restore()
is pointless (however we cannot change the prototype of sh_eth_close() as
it implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
ravb_close() always returns 0, hence the check in ravb_wol_restore() is
pointless (however, we cannot change the prototype of ravb_close() as it
implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do_div() does a 64-by-32 division. Here the divisor is an
unsigned long which on some platforms is 64 bit wide. So use
div64_ul instead of do_div to avoid a possible truncation.
Eliminate the following coccicheck warning:
./drivers/net/ethernet/renesas/ravb_main.c:2492:1-7: WARNING:
do_div() does a 64-by-32 division, please consider using div64_ul
instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/1637228883-100100-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo AVB->DMAC in comment, as the code following the comment
is for DMAC on Gigabit Ethernet IP.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables Receive/Transmit port of TOE and removes
the setting of promiscuous bit from EMAC configuration mode register.
This patch also update EMAC configuration mode comment from
"PAUSE prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX;
RX; CRC Pass Through".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document PFRI register bit, as it is documented on R-Car Gen3 and
RZ/G2L hardware manuals.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the feature bit "nc_queue" with "nc_queues" as AVB DMAC has
RX and TX NC queues.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the variable "tsrq" with "tccr_mask" as we are passing
TCCR mask to the ravb_wait() function.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for retrieving stats information for GbEthernet.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/G2L E-MAC supports carrier counters.
Add a carrier_counter hw feature bit to struct ravb_hw_info
to add this feature only for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_gbeth() function to support RZ/G2L.
This patch also renames ravb_rcar_rx to ravb_rx_rcar to be
consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_format_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_format to ravb_rx_ring_format_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_free_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_free to ravb_rx_ring_free_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_alloc_rx_desc_gbeth() function to support RZ/G2L.
This patch also renames ravb_alloc_rx_desc to ravb_alloc_rx_desc_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
R-Car AVB-DMAC has maximum 2K size on RX buffer, whereas on RZ/G2L
it is 8K. We need to allow for changing the MTU within the limit
of the maximum size of a descriptor.
Add a rx_max_buf_size variable to struct ravb_hw_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use ALIGN macro for calculating the value for max_rx_len.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with
the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports half duplex mode.
Add a half_duplex hw feature bit to struct ravb_hw_info for
supporting half duplex mode for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-MAC on R-Car supports magic packet detection, whereas RZ/G2L
does not support this feature. Add magic_pkt to struct ravb_hw_info
and enable this feature only for R-Car.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car AVB-DMAC has 4 Transmit start request queues, whereas
RZ/G2L has only 1 Transmit start request queue.
Add a tsrq variable to struct ravb_hw_info to handle this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports gPTP feature whereas RZ/G2L does not support it.
This patch excludes gtp feature support for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize GbEthernet DMAC found on RZ/G2L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L SoC has Gigabit Ethernet IP consisting of Ethernet controller
(E-MAC), Internal TCP/IP Offload Engine (TOE) and Dedicated Direct
memory access controller (DMAC).
This patch adds compatible string for RZ/G2L and fills up the
ravb_hw_info struct. Function stubs are added which will be used by
gbeth_hw_info and will be filled incrementally.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports network control queue whereas RZ/G2L does not support
it. Add nc_queue to struct ravb_hw_info, so that NC queue is handled
only by R-Car.
This patch also renames ravb_rcar_dmac_init to ravb_dmac_init_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the variable "no_ptp_cfg_active" with "gptp" and
"ptp_cfg_active" with "ccc_gac" to match the HW features.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename "ravb_set_features_rx_csum" function to "ravb_set_features_rcar" and
replace the function pointer "set_rx_csum_feature" with "set_feature".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset support is present on R-Car. Let's support it, if it is
available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E-MAC IP on the R-Car AVB module has different initialization
parameters for RX frame size, duplex settings, different offset
for transfer speed setting and has magic packet detection support
compared to E-MAC on RZ/G2L Gigabit Ethernet module. Factorise
the ravb_emac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC IP on the R-Car AVB module has different initialization
parameters for RCR, TGC, TCCR, RIC0, RIC2, and TIC compared to
DMAC IP on the RZ/G2L Gigabit Ethernet module. Factorise the
ravb_dmac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports HW checksum on RX and TX whereas R-Car supports on RX.
Factorise ravb_set_features to support this feature.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports 100 and 1000 Mbps transfer speed whereas RZ/G2L
in addition support 10Mbps. Factorise ravb_adjust_link function
in order to support 10Mbps speed.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses an extended descriptor in RX whereas, RZ/G2L uses
normal descriptor in RX. Factorise the ravb_rx function to
support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_init function uses an extended descriptor in RX for
R-Car and normal descriptor for RZ/G2L. Add a helper function
for RX ring buffer allocation to support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_format function uses an extended descriptor in RX
for R-Car compared to the normal descriptor for RZ/G2L. Factorise
RX ring buffer buildup to extend the support for later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses extended descriptor in RX, whereas RZ/G2L uses normal
descriptor. Factorise ravb_ring_free function so that it can
support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen3, gPTP support is active in config mode.
2) On R-Car Gen2, gPTP support is not active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a ptp_cfg_active hw feature bit to struct ravb_hw_info for
supporting gPTP active in config mode for R-Car Gen3.
This patch also removes enum ravb_chip_id, chip_id from both
struct ravb_hw_info and struct ravb_private, as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen2, gPTP support is not active in config mode.
2) On R-Car Gen3, gPTP support is active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a no_ptp_cfg_active hw feature bit to struct ravb_hw_info for
handling gPTP for R-Car Gen2.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports separate interrupts for E-MAC and DMA queues,
whereas R-Car Gen2 and RZ/G2L have a single interrupt instead.
Add a multi_irq hw feature bit to struct ravb_hw_info to enable
this only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For addressing 4 bytes alignment restriction on transmission
buffer for R-Car Gen2 we use 2 descriptors whereas it is a single
descriptor for other cases.
Replace the macros NUM_TX_DESC_GEN[23] with magic number and
add a comment to explain it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register for retrieving TX counters is present only on R-Car Gen3
and RZ/G2L; it is not present on R-Car Gen2.
Add the tx_counters hw feature bit to struct ravb_hw_info, to enable this
feature specifically for R-Car Gen3 now and later extend it to RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports TX and RX clock internal delay modes, whereas R-Car
Gen2 and RZ/G2L do not support it.
Add an internal_delay hw feature bit to struct ravb_hw_info to enable this
only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On R-Car the checksum calculation on RX frames is done by the E-MAC
module, whereas on RZ/G2L it is done by the TOE.
TOE calculates the checksum of received frames from E-MAC and outputs it to
DMAC. TOE also calculates the checksum of transmission frames from DMAC and
outputs it E-MAC.
Add net_features and net_hw_features to struct ravb_hw_info, to support
subsequent SoCs without any code changes in the ravb_probe function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stats strings for R-Car and RZ/G2L are different.
R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".
Add structure variables gstrings_stats and gstrings_size to struct
ravb_hw_info, so that subsequent SoCs can be added without any code
changes in the ravb_get_strings function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".
Replace RAVB_STATS_LEN macro with a structure variable stats_len to
struct ravb_hw_info, to support subsequent SoCs without any code changes
to the ravb_get_sset_count function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum descriptor size that can be specified on the reception side for
R-Car is 2048 bytes, whereas for RZ/G2L it is 8096.
Add the max_rx_len variable to struct ravb_hw_info for allocating different
RX skb buffer sizes for R-Car and RZ/G2L using the netdev_alloc_skb
function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen2 needs a 4byte aligned address for the transmission buffer,
whereas R-Car Gen3 doesn't have any such restriction.
Add aligned_tx to struct ravb_hw_info to select the driver to choose
between aligned and unaligned tx buffers.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP. With a few changes in the driver we
can support both IPs.
This patch adds the struct ravb_hw_info to hold hw features, driver data
and function pointers to support both the IPs. It also replaces the driver
data chip type with struct ravb_hw_info by moving chip type to it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of TX descriptors per packet is an unsigned value and
the variable for holding this information should be unsigned.
This patch replaces the data type of num_tx_desc variable in struct
ravb_private from 'int' to 'unsigned int'.
This patch also updates the data type of local variables to unsigned int,
where the local variables are evaluated using num_tx_desc.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The EtherAVB instances on the R-Car E3/D3 and RZ/G2E SoCs do not support
TX clock internal delay modes, and the EtherAVB driver prints a warning
if an unsupported "rgmii-*id" PHY mode is specified, to catch buggy
DTBs.
Commit a6f51f2efa ("ravb: Add support for explicit internal
clock delay configuration") deprecated deriving the internal delay mode
from the PHY mode, in favor of explicit configuration using the now
mandatory "rx-internal-delay-ps" and "tx-internal-delay-ps" properties,
thus delegating the warning to the legacy fallback code.
Since explicit configuration of a (valid) internal clock delay
configuration is enforced by validating device tree source files against
DT binding files, and all upstream DTS files have been converted as of
commit a5200e63af ("arm64: dts: renesas: rzg2: Convert EtherAVB to
explicit delay handling"), the checks in the legacy fallback code can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/2037542ac56e99413b9807e24049711553cc88a9.1628696778.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.
Fixes: 8ef7adc6be ("net: ethernet: ravb: Enable optional refclk")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable it when available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place the RX/TX descriptor bit *enum*s where they belong -- after the
corresponding RX/TX descriptor *struct*s and, while at it, switch to
declaring one *enum* entry per line...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename the rest of the *enum* tags still not (exactly) matching
the abbreviated register names from the manuals...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals (except R-Car gen2) the PHY status register's name
is abbreviated to PSR with the only valid bit 0 named LMON. Follow the
suit and rename the corresponding *enum* tag/entry.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals the TRSCER register bits match the corresponding
EESR registers's bits, but only on the R-Car gen2 SoC those are named
RINT<n> and TINT<n>. Follow the suit and rename the *enum* tag/entries
from DESC_I_* to TRSCER_*.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wolfram reports that his R-Car H2-based Lager board can no longer be
rebooted in v5.11-rc1, as it crashes with an imprecise external abort.
The issue can be reproduced on other boards (e.g. Koelsch with R-Car
M2-W) too, if CONFIG_IP_PNP is disabled, and the Ethernet interface is
down at reboot time:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=422b6835, *pte=00000000, *ppte=00000000
Internal error: : 1406 [#1] ARM
Modules linked in:
CPU: 0 PID: 1105 Comm: init Tainted: G W 5.10.0-rc1-00402-ge2f016cf7751 #1048
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
PC is at sh_mdio_ctrl+0x44/0x60
LR is at sh_mmd_ctrl+0x20/0x24
...
Backtrace:
[<c0451f30>] (sh_mdio_ctrl) from [<c0451fd4>] (sh_mmd_ctrl+0x20/0x24)
r7:0000001f r6:00000020 r5:00000002 r4:c22a1dc4
[<c0451fb4>] (sh_mmd_ctrl) from [<c044fc18>] (mdiobb_cmd+0x38/0xa8)
[<c044fbe0>] (mdiobb_cmd) from [<c044feb8>] (mdiobb_read+0x58/0xdc)
r9:c229f844 r8:c0c329dc r7:c221e000 r6:00000001 r5:c22a1dc4 r4:00000001
[<c044fe60>] (mdiobb_read) from [<c044c854>] (__mdiobus_read+0x74/0xe0)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e000
[<c044c7e0>] (__mdiobus_read) from [<c044c9d8>] (mdiobus_read+0x40/0x54)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e458
[<c044c998>] (mdiobus_read) from [<c044d678>] (phy_read+0x1c/0x20)
r7:ffffe000 r6:c221e470 r5:00000200 r4:c229f800
[<c044d65c>] (phy_read) from [<c044d94c>] (kszphy_config_intr+0x44/0x80)
[<c044d908>] (kszphy_config_intr) from [<c044694c>] (phy_disable_interrupts+0x44/0x50)
r5:c229f800 r4:c229f800
[<c0446908>] (phy_disable_interrupts) from [<c0449370>] (phy_shutdown+0x18/0x1c)
r5:c229f800 r4:c229f804
[<c0449358>] (phy_shutdown) from [<c040066c>] (device_shutdown+0x168/0x1f8)
[<c0400504>] (device_shutdown) from [<c013de44>] (kernel_restart_prepare+0x3c/0x48)
r9:c22d2000 r8:c0100264 r7:c0b0d034 r6:00000000 r5:4321fedc r4:00000000
[<c013de08>] (kernel_restart_prepare) from [<c013dee0>] (kernel_restart+0x1c/0x60)
[<c013dec4>] (kernel_restart) from [<c013e1d8>] (__do_sys_reboot+0x168/0x208)
r5:4321fedc r4:01234567
[<c013e070>] (__do_sys_reboot) from [<c013e2e8>] (sys_reboot+0x18/0x1c)
r7:00000058 r6:00000000 r5:00000000 r4:00000000
[<c013e2d0>] (sys_reboot) from [<c0100060>] (ret_fast_syscall+0x0/0x54)
As of commit e2f016cf77 ("net: phy: add a shutdown procedure"),
system reboot calls phy_disable_interrupts() during shutdown. As this
happens unconditionally, the PHY registers may be accessed while the
device is suspended, causing undefined behavior, which may crash the
system.
Fix this by wrapping the PHY bitbang accessors in the sh_eth driver by
wrappers that take care of Runtime PM, to resume the device when needed.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "undocumented" annotations in the EtherAVB driver were done against
the R-Car gen2 manuals; most of these registers/bits were then described
in the R-Car gen3 manuals -- reflect this fact in the annotations (note
that ECSIPR.LCHNGIP was documented in the recent R-Car gen2 manual)...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Follow the suit: remove #define APSR_DM
and rename #define's APSR_DM_{R|T}DM to APSR_{R|T}DM.
While at it, do several more things to the declaration of *enum* APSR_BIT:
- remove superfluous indentation;
- annotate APSR_MEMS as undocumented;
- annotate APSR as R-Car Gen3 only.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This caused issues with PHY drivers that
implement PHY internal delays properly[1]. Hence a backwards-compatible
workaround was added by masking the PHY mode[2].
Add proper support for explicit configuration of the MAC internal clock
delays using the new "[rt]x-internal-delay-ps" properties.
Fall back to the old handling if none of these properties is present.
[1] Commit bcf3440c6d ("net: phy: micrel: add phy-mode support for
the KSZ9031 PHY")
[2] Commit 9b23203c32 ("ravb: Mask PHY mode to avoid inserting
delays twice").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, full delay handling is done in both the probe and resume
paths. Split it in two parts, so the resume path doesn't have to redo
the parsing part over and over again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While fixing the W=1 builds, this warning came up because the
developers used a very tricky way to get structures initialized
to a non-zero value, but this causes GCC to warn about an
override. In this case the override was intentional, so just
disable the warning for this code with a kernel macro that results
in disabling the warning for compiles on GCC versions after 8.
It is not appropriate to change the struct to initialize all the
values as it will just add a lot more code for no value. The code
is completely correct as is, we just want to acknowledge that
this code could generate a warning and we're ok with that.
NOTE: the __diag_ignore macro currently only accepts a second
argument of 8 (version 80000), it's either use this one or
open code the pragma.
Fixed Warnings example (all the same):
drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init]
+ 256 more...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1838d6c62f.
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425a ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties. The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.
However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions. E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.
As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary. Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC. However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.
Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay. This also fixes messages
like:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"
as the PHY no longer sees the original RGMII-*ID mode.
Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register maps for the Gigabit controllers and the Ether one used on
RZ/A1 (AKA R7S72100) are identical except for GECMR which is only present
on the true GEther controllers. We no longer use the register map arrays
to determine if a given register exists, and have added the GECMR flag to
the 'struct sh_eth_cpu_data' in the previous patch, so we're ready to drop
the R7S72100 specific register map -- this saves 216 bytes of object code
(ARM gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Ether controllers having the Gigabit register layout have GECMR --
RZ/A1 (AKA R7S72100) actually has the same layout but no Gigabit speed
support and hence no GECMR. In the past, the new register map table was
added for this SoC, now I think we should have used the existing Gigabit
table with the differences (such as GECMR) covered by the mere flags in
the 'struct sh_eth_cpu_data'. Add such flag for GECMR -- and then we can
get rid of the R7S72100 specific layout in the next patch...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_xdfar flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RDFAR/TDFAR to be
considered for dumping on the R-Car gen1/2 SoCs (the register offset check
has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::cexcr flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RX packet counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_tx_cntrs flag I forgot to add the
flag check to __sh_eth_get_regs(), causing the non-existing TX counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: ce9134dff6 ("sh_eth: add sh_eth_cpu_data::no_tx_cntrs flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the renesas PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocates buffers sufficient for the maximum supported MTU (2026) in
order to eliminate the possibility of resource exhaustion when changing the
MTU while the device is up.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only use the TROCR register on R-Car Gen3 as it is not present on other
SoCs.
Offsets used for the undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas it
remains unclear why this driver accesses these fields on R-Car Gen2 but
regardless of what the historical reasons are the current code is
considered incorrect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of the undocumented BOC bit of the CCC register.
Current documentation for EtherAVB (ravb) describes the offset of what the
driver uses as the BOC bit as reserved and that only a value of 0 should be
written. After some internal investigation with Renesas it remains unclear
why this driver accesses these fields but regardless of what the historical
reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of the undocumented counter registers
CDCR, LCCR, CERCR, CEECR.
Offsets used for undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas
it remains unclear why this driver accesses these fields but regardless of
what the historical reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field name is FBP rather than FPB.
This field is unused and could equally be removed from the driver entirely.
But there seems no harm in leaving as documentation of the presence of the
field.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Tx timestamp is requested, a pointer to the skb is stored in the
ravb_tstamp_skb struct. This was done without an skb_get. There exists
the possibility that the skb could be freed by ravb_tx_free (when
ravb_tx_free is called from ravb_start_xmit) before the timestamp was
processed, leading to a use-after-free bug.
Use skb_get when filling a ravb_tstamp_skb struct, and add appropriate
frees/consumes when a ravb_tstamp_skb struct is freed.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Tho Vu <tho.vu.wh@rvc.renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995). And by extension it is also not supported by RZ/G2E (r9a774c0).
This matches all ES versions of the affected SoCs as it is
not clear if this problem will be resolved in newer chips.
This can be revisited, as necessary.
This patch does not error-out if PHY_INTERFACE_MODE_RGMII_ID or
PHY_INTERFACE_MODE_RGMII_TXID are used on SoCs where TX clock delay
mode is not supported as there is a risk of introducing a regression
when used in conjunction with older DT blobs present in the field.
Rather, a warning is logged in such cases.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.
Fixes: b356e978e9 ("sh_eth: add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware has the CBS (Credit Based Shaper) which affects only Q3
and Q2. When updating the CBS settings, even if the driver does so
after waiting for Tx DMA finished, there is a possibility that frame
data still remains in TxFIFO.
To avoid this, decrease TxFIFO depth of Q3 and Q2 to one.
This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM
and UDP_STREAM tests run on an Ebisu board. No performance change was
detected, outside of noise in the tests, both in terms of throughput and
CPU utilisation.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7763 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7734 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead Command Shared Object Symbol
9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user
7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
6.31% swapper [kernel.kallsyms] [k] default_idle_call
5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle
4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.52% netperf [kernel.kallsyms] [k] preempt_count_sub
1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg
1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres
1.78% netperf [kernel.kallsyms] [k] preempt_count_add
1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb
1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip
1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit
Test results with RX checksum offload disabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead Command Shared Object Symbol
7.00% swapper [kernel.kallsyms] [k] do_csum
3.94% swapper [kernel.kallsyms] [k] sh_eth_poll
3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user
2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.13% swapper [kernel.kallsyms] [k] default_idle_call
2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll
2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start
1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.32% netperf [kernel.kallsyms] [k] preempt_count_sub
1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area
1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled
1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
The above results collected on the R-Car V3H Starter Kit board.
Based on the commit 4d86d38186 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62e04b7e0e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB may provide a checksum of packet data appended to packet data. In
order to allow this checksum to be received by the host descriptor data
needs to be enlarged by 2 bytes to accommodate the checksum.
In the case of MTU-sized packets without a VLAN tag the
checksum were already accommodated by virtue of the space reserved for the
VLAN tag. However, a packet of MTU-size with a VLAN tag consumed all
packet data space provided by a descriptor leaving no space for the
trailing checksum.
This was not detected by the driver which incorrectly used the last two
bytes of packet data as the checksum and truncate the packet by two bytes.
This resulted all such packets being dropped.
A work around is to disable RX checksum offload
# ethtool -K eth0 rx off
This patch resolves this problem by increasing the size available for
packet data in RX descriptors by two bytes.
Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board
v2
* Use sizeof(__sum16) directly rather than adding a driver-local
#define for the size of the checksum provided by the hw (2 bytes).
Fixes: 4d86d38186 ("ravb: RX checksum offload")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since only full-duplex operation is supported by the
hardware, remove duplex handling code and keep the
register setting of ECMR.DM fixed at 1.
This updates the driver implementation to follow the
data sheet text "This bit should always be set to 1."
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the data sheet the Ethernet-AVB hardware in R-Car Gen3
and R-Car Gen2 SoCs do not support half duplex operation. So update
the driver to mark 100Mbit and 1Gbps HDX as unsupported.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit to ravb had the side effect of making the PHY
advertise Pause and Asym Pause, which previously did not happen. By
default, phydev->supported has both forms of pause enabled, but
phydev->advertising does not. The new phy_remove_link_mode() copies
phydev->supported to phydev->advertising after removing the requested
link mode. These Pause configuration bits appears it stops the PHY
from completing Auto-Neg and the link remains down. Be explicit and
remove the Pause and Asym Pause modes, so restoring the old behavior.
Fixes: 41124fa64d ("net: ethernet: Add helper to remove a supported link mode")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets from two descriptor to one descriptor because R-Car Gen3
does not have the 4 bytes alignment restriction of the transmission buffer.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the R7S9210 which is part of the RZ/A2 series.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry()
WRT their prototypes -- make them symmetric by passing to the former a TSU
register offset instead of its address and also adding the (now necessary)
'ndev' parameter...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can add the TSU register base address to a TSU register offset right
in sh_eth_tsu_write_entry(), no need to do it in its callers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With sh_eth_tsu_get_offset() now actually returning TSU register's offset,
we can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248
bytes of object code with AArch64 gcc 4.8.5... :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address,
not its offset. Make this function match its name and return a register's
offset from the TSU registers base address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_get_offset() is called several times by the driver, remove
*inline* and move that function from the header to the driver itself
to let gcc decide whether to expand it inline or not...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong helper is used to swap the bytes when adding the lower bits of
the TX descriptors tag field in the shared ds_tagl variable. The
variable contains the DS[11:0] field and then the TAG[3:0] bits.
The mistake was highlighted by the sparse warning:
ravb_main.c:1622:31: left side has type restricted __le16
ravb_main.c:1622:31: right side has type unsigned short
ravb_main.c:1622:31: warning: invalid assignment: |=
ravb_main.c:1622:34: warning: cast to restricted __le16
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse warning:
ravb_main.c:1257 ravb_get_strings() error: memcpy() '*ravb_gstrings_stats' too small (32 vs 960)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside a loop in ravb_get_ethtool_stats() a variable 'stats' is declared
resulting in the argument also named 'stats' to be shadowed. Fix this
warning by renaming the unused argument 'stats' to 'estats'.
This fixes the sparse warning:
ravb_main.c:1225:36: originally declared here
ravb_main.c:1233:41: warning: symbol 'stats' shadows an earlier one
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house ravb_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house ravb_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house ravb_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
ravb_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in ravb_adjust_link() only, also
now RX/TX is disabled when link is put down or modifications to E-MAC
registers ECMR and GECMR are expected for both cases of checked and
ignored link status pin state from E-MAC interrupt handler.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house sh_eth_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house sh_eth_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house sh_eth_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
sh_eth_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *enum* {A|M}PR_BIT were declared in the commit 86a74ff21a ("net:
sh_eth: add support for Renesas SuperH Ethernet") adding SH771x support,
however the SH771x manual doesn't have the APR/MPR registers described
and the code writing to them for SH7710 was later removed by the commit
380af9e390 ("net: sh_eth: CPU dependency code collect to "struct
sh_eth_cpu_data""). All the newer SoC manuals have these registers
documented as having a 16-bit TIME parameter of the PAUSE frame, not
1-bit -- update the *enum* accordingly, fixing up the APR/MPR writes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RPADIR exists, the value written to it is always the same for all SoCs
(and derived from NET_IP_ALIGN), so there has not been any need to store
it in the *struct* sh_eth_cpu_data...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *enum* RPADIR_BIT was declared in the commit 86a74ff21a ("net:
sh_eth: add support for Renesas SuperH Ethernet") adding SH771x support,
however the SH771x manual doesn't have the RPADIR register described and,
moreover, tells why the padding insertion must not be used. The newer SoC
manuals do have RPADIR documented, though with somewhat different layout --
update the *enum* according to these manuals...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing 'maxp' in sh_eth_soft_swap(), the buffer length needs
to be rounded up -- that's just asking for DIV_ROUND_UP()!
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_soft_swap() is called twice by the driver, remove *inline* and
move that function from the header to the driver itself to let gcc decide
whether to expand it inline or not...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Browsing thru the driver disassembly, I noticed that ARM gcc generated
no code whatsoever for sh_eth_soft_swap() while building a little-endian
kernel -- apparently __LITTLE_ENDIAN__ was not being #define'd, however
it got implicitly #define'd when building with the SH gcc (I could only
find the explicit #define __LITTLE_ENDIAN that was #include'd when building
a little-endian kernel). Luckily, the Ether controller only doing big-
endian DMA is encountered on the early SH771x SoCs only and all ARM SoCs
implement EDMR.DE and thus set 'sh_eth_cpu_data::hw_swap'. But anyway, we
need to fix the #ifdef inside sh_eth_soft_swap() to something that would
work on all architectures...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon has noticed a typo in the comment accompaining the BCULR write --
fix it and move the comment before the write (following the style of
the other comments), while at it...
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the verbs in the comments to the 'struct sh_eth_cpu_data' declaration
should be in a 3rd person singular, to match the nouns.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the EESR bit 8 is TRO (transmit retry over), not RTO.
Note that EESIPR bit 8, TROIP remained correct...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, add support for the DT probing of the R-Car V3H (AKA R8A77980) --
it's the only R-Car gen3 SoC having the GEther controller -- others have
only EtherAVB...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds the DMA burst mode bit
(NBST) in EDMR and the manual tells to always set it before doing any DMA.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds support for the RGMII
PHY interface mode as a new value for the RMII_MII register.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3365711df0 ("sh_eth: WARN on access to a register not implemented
in a particular chip") added WARN_ON() to sh_eth_{read|write}() but not
to sh_eth_tsu_{read|write}(). Now that we've routed almost all TSU register
accesses (except TSU_ADR{H|L}<n> -- which are special) thru the latter
pair of accessors, it makes sense to check for the unimplemented TSU
registers as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no particularly good reason TSU_POST<n> registers get accessed
circumventing sh_eth_tsu_{read|write}() -- start using those, removing
(badly named) sh_eth_tsu_get_post_reg_offset(), while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iff TSU registers exist on a given [G]Ether controller, they always include
the CAM entry table registers (TSU_ADR{H|L}<n>), thus the check for invalid
TSU_ADRH0 offset in __sh_eth_get_regs() is useless...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6ded286555 ("sh_eth: Fix RX recovery on R-Car in case of RX
ring underrun") added a check for an bad RDFAR offset in sh_eth_rx(), so
that the code could work on the R-Car Ether controllers which don't have
this register (and TDFAR), then the commit 3365711df0 ("sh_eth: WARN on
access to a register not implemented in a particular chip") replaced
offset 0 with 0xffff. Adding/checking the 'no_xdfar' bit field in the
'struct sh_eth_cpu_data' instead results in less object code...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEther controllers have CERCR/CEECR instead of CNDCR on the others.
Currently we are calling sh_eth_is_gether() in order to check for this,
however it would be simpler to check the new 'cexcr' bitfield in the
'struct sh_eth_cpu_data'; then we'd be able to remove sh_eth_is_gether()
as there would be no callers left...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/A1H (R7S72100) Ether controller doesn't seem to have the TX counter
registers like TROCR/CDCR/LCCR (or at least they are still undocumented
like some TSU registers), so we bail out of sh_eth_get_stats() early in
this case. Currently we are calling sh_eth_is_rz_fast_ether() in order
to check for this, but it would be simpler to check the new 'no_tx_cntrs'
bitfield in the 'struct sh_eth_cpu_data'; then we'd be able to remove
sh_eth_is_rz_fast_ether() as there would be no callers left...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GEther-like controllers have writeable RDFAR/TDFAR, on the others
they are read-only or just absent (on R-Car). Currently we are calling
sh_eth_is_{gether|rz_fast_ether}() in order to check if these registers
can be written to, however it would be simpler to check the new 'xdfar_rw'
bitfield in the 'struct sh_eth_cpu_data'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_get_edtrr_trns() returns the value to be written to EDTRR in order
to start TX DMA -- this value is different between the GEther-like and
the other controllers. We can replace this function (and thus get rid of
the calls to sh_eth_is_{gether|rz_fast_ether}() by it) with a new field
'edtrr_trns' in the 'struct sh_eth_cpu_data'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_reset() performs a software reset which is implemented in a
completely different way for the GEther-like controllers vs the other
controllers due to a different layout of EDMR (and other factors) --
it therefore makes sense to convert this function to a mandatory
sh_eth_cpu_data::soft_reset() method and thus get rid of the runtime
controller type check via sh_eth_is_{gether|rz_fast_ether}().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When addressing a review comment in a early version of the offending
patch a comment where left in which should have been removed. Remove the
comment to keep it consistent with the code.
Fixes: 75efa06f45 ("ravb: add support for changing MTU")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38 ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that the single port Ether controllers having TSU (like SH7734/
R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100
currently has -- they also don't have the TSU registers related e.g. to
passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port'
flag and use it as a new criterion for taking a "short path" in the TSU
init sequence in order to avoid writing to the non-existent registers...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Fixes: 73a0d90730 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSU_QTAG0/1 registers found in the Gigabit Ether controllers actually
have the same long name as the TSU_QTAGM0/1 registers in the early Ether
controllers: Qtag Addition/Deletion Set Register (Port 0/1 to 1/0); thus
there's no need to make a difference in sh_eth_tsu_init() between those
controllers. Unfortunately, we can't just remove TSU_QTAG0/1 from the
register *enum* because that would break the ethtool register dump...
Fixes: b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *while* loop in this function can be turned into a normal *for* loop.
And getting rid of the single return point saves us a few more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for changing the MTU within the limit of the maximum size of a
descriptor (2048 bytes). Add the callback to change MTU from user-space
and take the configurable MTU into account when configuring the
hardware.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the SH-ETH device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commits 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") and 744dddcae8 ("clk:
renesas: mstp: Keep wakeup sources active during system suspend"), this
workaround is no longer needed. Hence remove all explicit clock
handling to keep the device active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the EtherAVB device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commit 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") , this workaround is no longer
needed. Hence remove all explicit clock handling to keep the device
active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dual-port Ether configurations always have a shared TSU to e.g. pass
the packets between those ports. With the TSU init. code gathered under
the single *if*, we now can only get the port # from 'platform_device::id'
only when we actually need it (and not recalculate it each time)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_cpu_data::chip_reset() method always resets using ARSTR and
this register is always located at the start of the TSU register region.
Therefore, we can only call this method if we know TSU is there and thus
simplify the probing code a bit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARSTR is always located at the start of the TSU register region, thus
using add_reg() instead of add_tsu_reg() in __sh_eth_get_regs() to dump it
causes EDMR or EDSR (depending on the register layout) to be dumped instead
of ARSTR. Use the correct condition/macro there...
Fixes: 6b4b4fead3 ("sh_eth: Implement ethtool register dump operations")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error. Luckily, the driver never uses this
register. :-)
Fixes: 4a55530f38 ("net: sh_eth: modify the definitions of register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think that we can infer this information from the 'devno' variable
(set to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...
Fixes: 150647fb2c ("net: sh_eth: change the condition of initialization")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching the driver to the managed device API, I managed to break
the case of a dual Ether devices sharing a single TSU: the 2nd Ether port
wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy
and he then dropped the ball...
The solution is to limit calling devm_request_mem_region() to the first
of the two ports sharing the same TSU, so devm_ioremap_resource() can't
be used anymore for the TSU resource...
Fixes: d5e07e6921 ("sh_eth: use managed device API")
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Browsing thru the driver disassembly, I noticed that gcc was able to
figure out that the 'ndev' pointer is always non-NULL when calling
free_netdev() on the probe() method's error path and thus skip that
redundant NULL check... gcc is smart, be like gcc! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Browsing thru the driver disassembly, I noticed that gcc was able to
figure out that the 'ndev' pointer is always non-NULL when calling
free_netdev() on the probe() method's error path and thus skip that
redundant NULL check... gcc is smart, be like gcc! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fbf3d034f2.
As of commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NULL as argument for the DMA mapping API is bogus, as the DMA
mapping API may use information from the "struct device" to perform
the DMA mapping operation. Therefore, pass the appropriate "struct
device".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two types of "struct device": the one representing the
physical device on its physical bus (platform, SPI, PCI, etc.), and
the one representing the logical device in its device class (net,
etc.).
The DMA mapping API expects to receive as argument a "struct device"
representing the physical device, as the "struct device" contains
information about the bus that the DMA API needs.
However, the sh_eth driver mistakenly uses the "struct device"
representing the logical device (embedded in "struct net_device")
rather than the "struct device" representing the physical device on
its bus.
This commit fixes that by adjusting all calls to the DMA mapping API.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement fallback compatibility strings for R-Car Gen 1 and 2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Note that R-Car Gen2 and RZ/G1 have many compatible IP blocks. The
approach that has been consistently taken for other IP blocks is to name
common code, compatibility strings and so on after R-Car Gen2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename structures describing R-Car SoCs as rcar_gen[12]_*
rather than r8a77[79]x_*. This seems a little easier on the
eyes. And will make things slightly cleaner in a follow-up
patch that adds fallback-compatibility strings for these SoCs.
Note that R-Car Gen2 and RZ/G1 have many compatible IP blocks. The
approach that has been consistently taken for other IP blocks is to name
common code, compatibility strings and so on after R-Car Gen2.
Also rename sh_eth_set_rate_r8a777x as sh_eth_set_rate_rcar as
it it is used by the R-Car generations supported by the driver.
This patch should have no run-time effect and
is compile-tested only.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module clock is used for two purposes:
- Wake-on-LAN (WoL), which is optional,
- gPTP Timer Increment (GTI) configuration, which is mandatory.
As the clock is needed for GTI configuration anyway, WoL is always
available. Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload. This is enabled by default and
may be disabled and re-enabled using ethtool:
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
The RAVB provides a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by the
driver and used to update the skb accordingly.
In terms of performance throughput is close to gigabit line-rate both with
and without RX checksum offload enabled. Perf output, however, appears to
indicate that significantly less time is spent in do_csum(). This is as
expected.
Test results with RX checksum offload enabled:
# /usr/bin/perf_3.16 record -o /run/perf.data -a netperf -t TCP_MAERTS -H 10.4.3.162
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.4.3.162 () port 0 AF_INET : demo
enable_enobufs failed: getprotobyname
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 937.54
Summary of output of perf report:
18.28% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
10.34% ksoftirqd/0 [kernel.kallsyms] [k] __pi_memcpy
9.83% ksoftirqd/0 [kernel.kallsyms] [k] ravb_poll
7.89% ksoftirqd/0 [kernel.kallsyms] [k] skb_put
4.01% ksoftirqd/0 [kernel.kallsyms] [k] dev_gro_receive
3.37% netperf [kernel.kallsyms] [k] __arch_copy_to_user
3.17% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.55% swapper [kernel.kallsyms] [k] tick_nohz_idle_enter
2.04% ksoftirqd/0 [kernel.kallsyms] [k] __pi___inval_dcache_area
2.03% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.96% ksoftirqd/0 [kernel.kallsyms] [k] __netdev_alloc_skb
1.59% ksoftirqd/0 [kernel.kallsyms] [k] __slab_alloc.isra.83
Test results without RX checksum offload enabled:
# /usr/bin/perf_3.16 record -o /run/perf.data -a netperf -t TCP_MAERTS -H 10.4.3.162
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.4.3.162 () port 0 AF_INET : demo
enable_enobufs failed: getprotobyname
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 940.20
Summary of output of perf report:
17.10% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
10.99% ksoftirqd/0 [kernel.kallsyms] [k] __pi_memcpy
8.87% ksoftirqd/0 [kernel.kallsyms] [k] ravb_poll
8.16% ksoftirqd/0 [kernel.kallsyms] [k] skb_put
7.42% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.91% ksoftirqd/0 [kernel.kallsyms] [k] dev_gro_receive
2.31% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.16% ksoftirqd/0 [kernel.kallsyms] [k] __pi___inval_dcache_area
2.14% ksoftirqd/0 [kernel.kallsyms] [k] __netdev_alloc_skb
1.93% netperf [kernel.kallsyms] [k] __arch_copy_to_user
1.79% swapper [kernel.kallsyms] [k] tick_nohz_idle_enter
1.63% ksoftirqd/0 [kernel.kallsyms] [k] __slab_alloc.isra.83
Above results collected on an R-Car Gen 3 Salvator-X/r8a7796 ES1.0.
Also tested on a R-Car Gen 3 Salvator-X/r8a7795 ES1.0.
By inspection this also appears to be compatible with the ravb found
on R-Car Gen 2 SoCs, however, this patch is currently untested on such
hardware.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The renesas-cpg-mssr clock driver are not yet aware of PSCI sleep where
power is cut to the SoC. When resuming from this state with WoL enabled
the enable count of the ravb clock is 1 and the clock driver thinks the
clock is already on when PM core enables the clock and increments the
enable count to 2. This will result in the ravb driver failing to talk
to the hardware since the module clock is off. Work around this by
forcing the enable count to 0 and then back to 2 when resuming with WoL
enabled.
This workaround should be reverted once the renesas-cpg-mssr clock
driver becomes aware of this PSCI sleep behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL is enabled in the suspend callback by setting MagicPacket detection
and disabling all interrupts expect MagicPacket. In the resume path the
driver needs to reset the hardware to rearm the WoL logic, this prevents
the driver from simply restoring the registers and to take advantage of
that ravb was not suspended to reduce resume time. To reset the
hardware the driver closes the device, sets it in reset mode and reopens
the device just like it would do in a normal suspend/resume scenario
without WoL enabled, but it both closes and opens the device in the
resume callback since the device needs to be reset for WoL to work.
One quirk needed for WoL is that the module clock needs to be prevented
from being switched off by Runtime PM. To keep the clock alive the
suspend callback need to call clk_enable() directly to increase the
usage count of the clock. Then when Runtime PM decreases the clock usage
count it won't reach 0 and be switched off.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports the MTU to be changed and the driver it self is
somewhat prepared to support this. This patch hooks up the callbacks to
be able to change the MTU from user-space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0b ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_put_padto() fails then it frees the skb. I shifted that code
up a bit to make my error handling a little simpler.
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API debugging (when enabled) causes:
WARNING: CPU: 0 PID: 1445 at lib/dma-debug.c:519 add_dma_entry+0xe0/0x12c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x01b2974d
to be printed after repeated initialization of the Ether device, e.g.
suspend/resume or 'ifconfig' up/down. This is because DMA buffers mapped
using dma_map_single() in sh_eth_ring_format() and sh_eth_start_xmit() are
never unmapped. Resolve this problem by unmapping the buffers when freeing
the descriptor rings; in order to do it right, we'd have to add an extra
parameter to sh_eth_txfree() (we rename this function to sh_eth_tx_free(),
while at it).
Based on the commit a47b70ea86 ("ravb: unmap descriptors when freeing
rings").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a link change interrupt happens along side the MagicPacket interrupt
and the link change interrupt is ignored the interrupt handler will
return and the wakeup event is not registered. Fix this by moving the
MagicPacket check before the link change check.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be consistent with the rest of the driver when setting bits using
sh_eth_modify() the same bit should also be cleared. This have no
functional change and should have been done from the start.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have almost all EESIPR bits declared (and those that are
still not are most probably reserved anyway) we can at last replace the
bare numbers used for 'sh_eth_cpu_data::eesipr_value' initializers with
the bit names ORed together...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH77{34|63} manuals describe more EESIPR bits than the current
driver. Declare the new bits with the end goal of using the bit names
instead of the bare numbers for the 'sh_eth_cpu_data::eesipr_value'
initializers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
the *enum* declaring the EESIPR bits (interrupt mask) went out of sync with
the *enum* declaring the EESR bits (interrupt status) WRT bit naming and
formatting. I'd like to restore the consistency by using EESIPR as the bit
name prefix, renaming the *enum* to EESIPR_BIT, and (finally) renaming the
bits according to the available Renesas SH77{34|63} manuals; additionally,
reconstruct couple names using the EESR bit declaration above...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
