ravb_set_gti() was computing the value of GTI based on the reference clock
rate and then applied it to register. This was done on the driver's probe
function. In order to implement runtime PM for all IP variants (as some IP
variants switches to reset mode (and thus the registers content is lost)
when module standby is configured through clock APIs) the GTI setup was
split in 2 parts: one computing the value of the GTI register (done in the
driver's probe function) and one applying the computed value to register
(done in the driver's ndo_open API).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The runtime PM implementation will disable clocks at the end of
ravb_probe(). As some IP variants switch to reset mode as a result of
setting module standby through clock disable APIs, to implement runtime PM
the resource parsing and requesting are moved in the probe function and IP
settings are moved in the open function. This is done because at the end of
the probe some IP variants will switch anyway to reset mode and the
registers content is lost. Also keeping only register settings operations
in the ravb_open()/ravb_close() functions will make them faster.
Commit moves IRQ requests to ravb_probe() to have all the IRQs ready when
the interface is open. As now getting/requesting IRQs is done in a single
place there is no need to keep intermediary data (like ravb_rx_irqs[] and
ravb_tx_irqs[] arrays or IRQs in struct ravb_private).
In order to avoid accessing the IP registers while the IP is runtime
suspended (e.g. in the timeframe b/w the probe requests shared IRQs and
IP clocks are enabled) in the interrupt handlers were introduced
pm_runtime_active() checks. The device runtime PM usage counter has been
incremented to avoid disabling the device's clocks while the check is in
progress (if any).
This is a preparatory change to add runtime PM support for all IP variants.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reference clock could be or not be part of the power domain. If it is part
of the power domain, the power domain takes care of properly setting it. In
case it is not part of the power domain and full runtime PM support is
available in driver the clock will not be propertly disabled/enabled at
runtime. For this, keep the prepare/unprepare operations in the driver's
probe()/remove() functions and move the enable/disable in runtime PM
functions.
By doing this, the previous ravb_runtime_nop() function was renamed
ravb_runtime_suspend() and the comment was removed. A proper runtime PM
resume function was added (ravb_runtime_resume()). The current driver
still don't need to make any register settings on runtime suspend/resume
(as expressed in the removed comment) because, currently,
pm_runtime_put_sync() is called on the driver remove function. This will be
changed in the next commits (that extends the runtime PM support) such
that proper register settings (along with runtime resume/suspend) will be
done on ravb_open()/ravb_close().
Along with it, the other clock request operations were moved close to
reference clock request and prepare to have all the clock requests
specific code grouped together.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RZ/G3S can go to deep sleep states where power to most of the SoC parts is
off. When resuming from such a state, the Ethernet controller needs to be
reinitialized. De-asserting the reset signal for it should also be done.
Thus, add reset assert/de-assert on suspend/resume functions.
On the resume function, the de-assert was not reverted in case of failures
to give the user a chance to restore the interface (e.g., bringing down/up
the interface) in case suspend/resume failed.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use tabs instead of spaces in the ravb_set_rate_gbeth() function.
This aligns with the coding style requirements.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated now
and require __maybe_unused protection against unused function warnings.
The usage of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/RUNTIME_PM_OPS() allows
the compiler to see the functions, thus suppressing the warning. Thus
drop the __maybe_unused markings.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On the RZ/G3S SoC the reset controller is mandatory for the IP to work.
The device tree binding documentation for the ravb driver specifies that
the resets are mandatory. Based on this, make the resets mandatory also in
driver for all ravb devices.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ravb_rzv2m_hw_info::gptp_ref_clk is enabled only for RZ/V2M. RZ/V2M
is an ARM64-based device which selects power domains by default and
CONFIG_PM. The RZ/V2M Ethernet DT node has proper power-domain binding
available in device tree from the commit that added the Ethernet node.
(4872ca1f92 ("arm64: dts: renesas: r9a09g011: Add ethernet nodes")).
Power domain support was available in the rzg2l-cpg.c driver when the
Ethernet DT node has been enabled in RZ/V2M device tree.
(ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")).
Thus, remove the explicit clock enable for gptp_clk (and treat it as the
other clocks are treated) as it is not needed and removing it doesn't
break the ABI according to the above explanations.
By removing the enable/disable operation from the driver we can add
runtime PM support (which operates on clocks) w/o the need to handle
the gptp_clk in the Ethernet driver functions like ravb_runtime_nop().
PM domain does all that is needed.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ravb_poll() initial code used to interrogate the first descriptor of the
RX queue in case gPTP is false to determine if ravb_rx() should be called.
This is done for non-gPTP IPs. For gPTP IPs the driver PTP-specific
information was used to determine if receive function should be called. As
every IP has its own receive function that interrogates the RX descriptors
list in the same way the ravb_poll() was doing there is no need to double
check this in ravb_poll(). Removing the code from ravb_poll() leads to a
cleaner code.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In ravb_start_xmit(), ravb driver uses u32 variable to store result of
dma_map_single() call. Since ravb hardware has 32-bit address fields in
descriptors, this works properly when mapping is successful - it is
platform's job to provide mapping addresses that fit into hardware
limitations.
However, in failure case dma_map_single() returns DMA_MAPPING_ERROR
constant that is 64-bit when dma_addr_t is 64-bit. Storing this constant
in u32 leads to truncation, and further call to dma_mapping_error()
fails to notice the error.
Fix that by storing result of dma_map_single() in a dma_addr_t
variable.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CSR.OPS bits specify the current operating mode and (according to
documentation) they are updated by HW when the operating mode change
request is processed. To comply with this check CSR.OPS before proceeding.
Commit introduces ravb_set_opmode() that does all the necessities for
setting the operating mode (set CCC.OPC (and CCC.GAC, CCC.CSEL, if any) and
wait for CSR.OPS) and call it where needed. This should comply with all the
HW manuals requirements as different manual variants specify that different
modes need to be checked in CSR.OPS when setting CCC.OPC.
If gPTP active in config mode is supported and it needs to be enabled, the
CCC.GAC and CCC.CSEL needs to be configured along with CCC.OPC in the same
write access. For this, ravb_set_opmode() allows passing GAC and CSEL as
part of opmode and the function updates accordingly CCC register.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow jumbo frames by changing maximum MTU size and number of RX queues.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add handling specific descriptor types F{START,MID,END}. However,
such jumbo frames will not happen yet because the maximum MTU size is
still default for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this hardware receives a jumbo frame like 2KiB or more, it will be
split into multiple queues. In the near future, to support this,
add handling specific descriptor types F{START,MID,END}. However, such
jumbo frames will not happen yet because the maximum MTU size is still
default for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support jumbo frames, set GWMDNC register with acceptable maximum
values for TX and RX.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add a setting ext descriptor function to improve code readability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add unmap_addrs array to unmap dma mapping address instead of dma
address in each TX descriptor because the descriptors may not have
the top dma address.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this hardware receives a jumbo frame like 2KiB or more, it will be
split into multiple queues. In the near future, to support this, use
build_skb() instead of netdev_alloc_skb_ip_align().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index should not be negative, so use unsigned int for
descriptors related array index.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused argument and return value of rswitch_tx_free() to
simplify the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When breaking out the Gen4 gPTP support to its own module the dependency
on the PTP_1588_CLOCK framework was left as optional and only stated for
the driver using the module. This leads to issues when doing
COMPILE_TEST of RENESAS_GEN4_PTP separately and PTP_1588_CLOCK is built
as a module and the other as a built-in. Add an explicit depend on
PTP_1588_CLOCK.
While at it remove the optional support for PTP_1588_CLOCK from
RENESAS_ETHER_SWITCH as the driver unconditionally calls the Gen4 gPTP
module and thus also requires the PTP_1588_CLOCK framework.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8c1c66235e ("net: ethernet: renesas: rcar_gen4_ptp: Break out to module")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231129111142.3322667-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ravb_phy_start() may fail. If that happens, the TX queues will remain
started. Thus, move the netif_tx_start_all_queues() after PHY is
successfully initialized.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This .ndo_start_xmit() function should return netdev_tx_t value,
not -ENOMEM. So, fix it.
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of ret in rswitch_start_xmit() should be netdev_tx_t. So,
fix it.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Gen4 gPTP support will be shared between the existing Renesas
Ethernet Switch driver and the upcoming Renesas Ethernet-TSN driver. In
preparation for this break out the gPTP support to its own module.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of using hard coded clock increment values for each SoC derive
the clock increment from the module clock. This is done in preparation
to support a second platform, R-Car V4H that uses a 200Mhz clock
compared with the 320Mhz clock used on R-Car S4.
Tested on both SoCs,
S4 reports a clock of 320000000Hz which gives a value of 0x19000000.
Documentation says a 320Mhz clock is used and the correct increment for
that clock is 0x19000000.
V4H reports a clock of 199999992Hz which gives a value of 0x2800001a.
Documentation says a 200Mhz clock is used and the correct increment for
that clock is 0x28000000.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All known R-Car Gen4 SoC share the same register layout, rename the
R-Car S4 specific identifiers so they can be shared with the upcoming
R-Car V4H support.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of printing a warning and proceeding with an unknown register
layout return an error. The only call site is already prepared to
propagate the error.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The comments intent was to indicates which function uses the enum. While
upstreaming rcar_gen4_ptp the function was renamed but this comment was
left with the old function name.
Instead of correcting the comment remove it, it adds little value.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Mentioning SoCs in Kconfig descriptions tends to get stale (e.g. RAVB is
missing RZV2M) or imprecise (e.g. SH_ETH is not available on all
R8A779x). Drop them instead of providing vague information. Improve the
file description a tad while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20231022205316.3209-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new Renesas driver shall be added soon. Prepare the Makefile by
grouping the specific objects to the Kconfig symbol for better
readability. Improve the file description a tad while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20231022205316.3209-2-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add PM ops for Suspend to Idle. When the system suspended,
the Ethernet Serdes's clock will be stopped. So, this driver needs
to re-initialize the Ethernet Serdes by phy_init() in
renesas_eth_sw_resume(). Otherwise, timeout happened in phy_power_on().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Array index should not be negative, so modify the condition of
rswitch_for_each_enabled_port_continue_reverse() macro, and then
use unsigned int instead.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c ("bpf: Fix verifier log for async callback return values")
a923819fb2 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_power_off() should not be called if phy_power_on() failed.
So, add a condition .power_count before calls phy_power_off().
Fixes: 5cb630925b ("net: renesas: rswitch: Add phy_power_{on,off}() calling")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix functions calling order and a condition in renesas_eth_sw_remove().
Otherwise, kernel NULL pointer dereference happens from phy_stop() if
a net device opens.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reported-by: Zheng Wang <zyytlz.wz@163.com>
Closes: https://lore.kernel.org/netdev/20230725030026.1664873-1-zyytlz.wz@163.com/
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ravb_remove(), dma_free_coherent() should be call after
unregister_netdev(). Otherwise, this controller is possible to use
the freed buffer.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add .[gs]et_link_ksettings support by using
phy_ethtool_[gs]et_link_ksettings() functions.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807003231.1552062-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The latest SoC version can support runtime speed change. So,
add detect SoC version by using soc_device_match() and then
reconfigure the hardware of this and SerDes if needed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807003231.1552062-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this driver used the "global rate limiter" feature of GWCA,
the TX performance of each port was reduced when multiple ports
transmitted frames simultaneously. To improve performance, remove
the use of the "global rate limiter" feature and use "hardware pause"
features of the following:
- "per priority pause" of GWCA
- "global pause" of COMA
Note that these features are not related to the ethernet PAUSE frame.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware can receive multiple frames so that using
napi_gro_receive() instead of netif_receive_skb() gets good
performance of RX.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamp descriptors were intended to act cyclically. Descriptors
from index 0 through gq->ring_size - 1 contain actual information, and
the last index (gq->ring_size) should have LINKFIX to indicate
the first index 0 descriptor. However, the LINKFIX value is missing,
causing the timestamp feature to stop after all descriptors are used.
To resolve this issue, set the LINKFIX to the timestamp descritors.
Reported-by: Phong Hoang <phong.hoang.wz@renesas.com>
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix return value in the error path of rswitch_start_xmit(). If TX
queues are full, this function should return NETDEV_TX_BUSY.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230529073817.1145208-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit ce1fdb0656. It turned
out this actually introduces a race condition. netif_running() is not a
suitable check for get_stats.
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230327152112.15635-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_disconnect() calls phy_detach() which already clears 'phydev' if it
is attached to a struct net_device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321131745.27688-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It had a purpose back in the days, but today we have a handy helper.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321065826.2044-1-wsa+renesas@sang-engineering.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since the GWCA has the TX timestamp feature, this driver
should not disable it if one of ports is opened. So, fix it.
Reported-by: Phong Hoang <phong.hoang.wz@renesas.com>
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RX descriptor doesn't have any data, the output value of quote
from rswitch_rx() will be increased unexpectedily. So, fix it.
Reported-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SH_ETH doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 6a1dbfefda ("net: sh_eth: Fix PHY state warning splat during system resume")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RAVB doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 4924c0cdce ("net: ravb: Fix PHY state warning splat during system resume")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/all/20230307163041.3815-8-wsa+renesas@sang-engineering.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous code, TX timestamp accuracy was bad because the irq
handler got the timestamp from the timestamp register at that time.
This hardware has "Timestamp capture" feature which can store
each TX timestamp into the timestamp descriptors. To improve
TX timestamp accuracy, implement timestamp descriptors' handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous code, the gptp flag was completely related to
the !dir_tx in struct rswitch_gwca_queue because
rswitch_gwca_queue_alloc() was called below:
< In rswitch_txdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->tx_queue, true, false,
TX_RING_SIZE);
So, dir_tx = true, and gptp = false.
< In rswitch_rxdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->rx_queue, false, true,
RX_RING_SIZE);
So, dir_tx = false, and gptp = true.
In the future, a new queue handling for timestamp will be implemented
and this gptp flag is confusable. So, remove the gptp flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To improve readability, move linkfix related variables to
struct rswitch_gwca. Also, rename function names "desc" with "linkfix".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To add a new ring which is really related to timestamp (ts_ring)
in the future, rename the following members to improve readability:
ring --> tx_ring
ts_ring --> rx_ring
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous code set the speed by the interface mode of PHY.
Also this hardware has a restriction which cannot change the speed
at runtime. To use other speed, add "max-speed" handling to set
each port's speed if needed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHYs (like marvell10g) will decide the host interface
mode by the media-side speed. So, the rswitch driver needs to
initialize one of the Ethernet SERDES (r8a779f0-eth-serdes) ports
after linked the Ethernet PHY up. The r8a779f0-eth-serdes driver has
.init() for initializing all ports and .power_on() for initializing
each port. So, add phy_power_{on,off} calling for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set phydev->host_interfaces before calling of_phy_connect() to
configure the PHY with the information of host_interfaces.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intended to set phy_device->host_interfaces by phylink in the future.
But there is difficult to implement phylink properly, especially
supporting the in-band mode on this driver because extra initialization
is needed after linked the ethernet PHY up. So, convert to phy_device
from phylink.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify struct phy *serdes handling by keeping the valiable in
the struct rswitch_device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this driver enables the interrupt by RIC2_QFE1, this driver
should clear the interrupt flag if it happens. Otherwise, the interrupt
causes to hang the system.
Note that this also fix a minor coding style (a comment indentation)
around the fixed code.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After system entered Suspend to RAM, registers setting of this
hardware is reset because the SoC will be turned off. On R-Car Gen3
(info->ccc_gac), ravb_ptp_init() is called in ravb_probe() only. So,
after system resumed, it lacks of the initial settings for ptp. So,
add ravb_ptp_{init,stop}() into ravb_{resume,suspend}().
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
If one of ports in the ethernet-ports was disabled, this driver
failed to probe all ports. So, fix it.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230120001959.1059850-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rswitch MDIO bus driver only supports C45 transfers. Update the
function names to make this clear, pass the mmd as a parameter, and
register the accessors to the _c45 ops of the bus driver structure.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bitbbanging bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new driver API calls.
The SH Ethernet driver places wrappers around these functions. In
order to not break boards which might be using C45, add similar
wrappers for C45 operations.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To get mac address from device tree which is from each ethernet-port,
fix the first argument of of_get_ethdev_address().
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rswitch_init() returns non-zero and this driver is re-probed,
the following error happens:
renesas_eth_sw e6880000.ethernet: Unbalanced pm_runtime_enable!
So, fix error path in renesas_eth_sw_probe().
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the error "ravb 11c20000.ethernet eth0: failed to switch
device to config mode" during unbind.
We are doing register access after pm_runtime_put_sync().
We usually do cleanup in reverse order of init. Currently in
remove(), the "pm_runtime_put_sync" is not in reverse order.
Probe
reset_control_deassert(rstc);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
remove
pm_runtime_put_sync(&pdev->dev);
unregister_netdev(ndev);
..
ravb_mdio_release(priv);
pm_runtime_disable(&pdev->dev);
Consider the call to unregister_netdev()
unregister_netdev->unregister_netdevice_queue->rollback_registered_many
that calls the below functions which access the registers after
pm_runtime_put_sync()
1) ravb_get_stats
2) ravb_close
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221214105118.2495313-1-biju.das.jz@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The skb is delivered to napi_gro_receive() which may free it, after calling this,
dereferencing skb may trigger use-after-free.
Fixes: 1c59eb678c ("ravb: Fillup ravb_rx_gbeth() stub")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221203092941.10880-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After system resumed on some environment board, the promiscuous mode
is disabled because the SoC turned off. So, call ravb_set_rx_mode() in
the ravb_resume() to fix the issue.
Reported-by: Tho Vu <tho.vu.wh@renesas.com>
Fixes: 0184165b2f ("ravb: add sleep PM suspend/resume support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20221128065604.1864391-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch detected the following warning.
drivers/net/ethernet/renesas/rswitch.c:1717 rswitch_init() warn:
'%pM' cannot be followed by 'n'
The 'n' should be '\n'.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rswitch_etha_wait_link_verification() is supposed to return zero
on success or negative error codes. Unfortunately it is declared as a
bool so the caller treats everything as success.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/Y3OPo6AOL6PTvXFU@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If CONFIG_PTP_1588_CLOCK_OPTIONAL=m and CONFIG_RENESAS_ETHER_SWITCH=y,
the following build error happened:
aarch64-linux-ld: DWARF error: could not find abbrev number 60
drivers/net/ethernet/renesas/rswitch.o: in function `rswitch_get_ts_info':
rswitch.c:(.text+0x408): undefined reference to `ptp_clock_index'
aarch64-linux-ld: DWARF error: could not find abbrev number 1190123
drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_register':
rcar_gen4_ptp.c:(.text+0x4dc): undefined reference to `ptp_clock_register'
aarch64-linux-ld: drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_unregister':
rcar_gen4_ptp.c:(.text+0x584): undefined reference to `ptp_clock_unregister'
To fix the issue, add "depends on PTP_1588_CLOCK_OPTIONAL" into the
Kconfig.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6c6fa1a00a ("net: ethernet: renesas: rswitch: Add R-Car Gen4 gPTP support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221110012720.3552060-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coverity reported that the error path in rswitch_gwca_queue_alloc_skb()
has an issue to cause endless loop. So, fix the issue by changing
variables' types from u32 to int. After changed the types,
rswitch_tx_free() should use rswitch_get_num_cur_queues() to
calculate number of current queues.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1527147 ("Control flow issues")
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221107081021.2955122-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/net/ethernet/renesas/rswitch.c:1533:20: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = rswitch_start_xmit,
^~~~~~~~~~~~~~~~~~
1 error generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of rswitch_start_xmit()
to match the prototype's to resolve the warning and CFI failure.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221103220032.2142122-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add R-Car Gen4 gPTP support into the rswitch driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial support for Renesas "Ethernet Switch" device of R-Car S4-8.
The hardware has features about forwarding for an ethernet switch
device. But, for now, it acts as ethernet controllers so that any
forwarding offload features are not supported. So, any switchdev
header files and DSA framework are not used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb implementation of .adjfreq is implemented in terms of a
straight forward "base * ppb / 1 billion" calculation.
Convert this driver to .adjfine and use the adjust_by_scaled_ppm helper
function to calculate the new addend.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 626 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xe4
As the Renesas SuperH Ethernet driver already calls phy_{stop,start}()
in its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/c6e1331b9bef61225fa4c09db3ba3e2e7214ba2d.1663598886.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EMAC IP found on RZ/G2L Gb ethernet supports MII interface.
This patch adds support for selecting MII interface mode.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20220914192604.265859-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the Renesas Ethernet AVB (EtherAVB-IF) blocks on R-Car
Gen4 SoCs (e.g. R-Car V4H) by matching on a family-specific compatible
value.
These are treated the same as EtherAVB on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/2ee968890feba777e627d781128b074b2c43cddb.1662718171.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/V2M Ethernet is very similar to R-Car Gen3 Ethernet-AVB, though
some small parts are the same as R-Car Gen2.
Other differences to R-Car Gen3 and Gen2 are:
* It has separate data (DI), error (Line 1) and management (Line 2) irqs
rather than one irq for all three.
* Instead of using the High-speed peripheral bus clock for gPTP, it has a
separate gPTP reference clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/V2M has a separate gPTP reference clock that is used when the
AVB-DMAC Mode Register (CCC) gPTP Clock Select (CSEL) bits are
set to "01: High-speed peripheral bus clock".
Therefore, add a feature that allows this clock to be used for
gPTP.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car has a combined interrupt line, ch22 = Line0_DiA | Line1_A | Line2_A.
RZ/V2M has separate interrupt lines for each of these, so add a feature
that allows the driver to get these interrupts and call the common handler.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the HW has a single interrupt, the driver uses the
GIC, TIC, RIC0 registers to enable and disable interrupts.
When the HW has multiple interrupts, it uses the GIE, GID, TIE, TID,
RIE0, RID0 registers.
However, other devices, e.g. RZ/V2M, have multiple irqs and only have
the GIC, TIC, RIC0 registers.
Therefore, split this into a separate feature.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
'max_rx_len' can be up to GBETH_RX_BUFF_MAX (i.e. 8192) (see
'gbeth_hw_info').
The default value of 'num_rx_ring' can be BE_RX_RING_SIZE (i.e. 1024).
So this loop can allocate 8 Mo of memory.
Previous memory allocations in this function already use GFP_KERNEL, so
use __netdev_alloc_skb() and an explicit GFP_KERNEL instead of a
implicit GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_{suspend|resume}() initialize their local variable 'ret' to 0 but
this value is never really used, thus we can kill those intializers...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/f09d7c64-4a2b-6973-09a4-10d759ed0df4@omp.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() always returns 0, hence the check in sh_eth_wol_restore()
is pointless (however we cannot change the prototype of sh_eth_close() as
it implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
ravb_close() always returns 0, hence the check in ravb_wol_restore() is
pointless (however, we cannot change the prototype of ravb_close() as it
implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do_div() does a 64-by-32 division. Here the divisor is an
unsigned long which on some platforms is 64 bit wide. So use
div64_ul instead of do_div to avoid a possible truncation.
Eliminate the following coccicheck warning:
./drivers/net/ethernet/renesas/ravb_main.c:2492:1-7: WARNING:
do_div() does a 64-by-32 division, please consider using div64_ul
instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/1637228883-100100-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo AVB->DMAC in comment, as the code following the comment
is for DMAC on Gigabit Ethernet IP.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables Receive/Transmit port of TOE and removes
the setting of promiscuous bit from EMAC configuration mode register.
This patch also update EMAC configuration mode comment from
"PAUSE prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX;
RX; CRC Pass Through".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document PFRI register bit, as it is documented on R-Car Gen3 and
RZ/G2L hardware manuals.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the feature bit "nc_queue" with "nc_queues" as AVB DMAC has
RX and TX NC queues.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the variable "tsrq" with "tccr_mask" as we are passing
TCCR mask to the ravb_wait() function.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for retrieving stats information for GbEthernet.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/G2L E-MAC supports carrier counters.
Add a carrier_counter hw feature bit to struct ravb_hw_info
to add this feature only for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_gbeth() function to support RZ/G2L.
This patch also renames ravb_rcar_rx to ravb_rx_rcar to be
consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_format_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_format to ravb_rx_ring_format_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_free_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_free to ravb_rx_ring_free_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_alloc_rx_desc_gbeth() function to support RZ/G2L.
This patch also renames ravb_alloc_rx_desc to ravb_alloc_rx_desc_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
R-Car AVB-DMAC has maximum 2K size on RX buffer, whereas on RZ/G2L
it is 8K. We need to allow for changing the MTU within the limit
of the maximum size of a descriptor.
Add a rx_max_buf_size variable to struct ravb_hw_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use ALIGN macro for calculating the value for max_rx_len.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with
the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports half duplex mode.
Add a half_duplex hw feature bit to struct ravb_hw_info for
supporting half duplex mode for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-MAC on R-Car supports magic packet detection, whereas RZ/G2L
does not support this feature. Add magic_pkt to struct ravb_hw_info
and enable this feature only for R-Car.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car AVB-DMAC has 4 Transmit start request queues, whereas
RZ/G2L has only 1 Transmit start request queue.
Add a tsrq variable to struct ravb_hw_info to handle this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports gPTP feature whereas RZ/G2L does not support it.
This patch excludes gtp feature support for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize GbEthernet DMAC found on RZ/G2L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L SoC has Gigabit Ethernet IP consisting of Ethernet controller
(E-MAC), Internal TCP/IP Offload Engine (TOE) and Dedicated Direct
memory access controller (DMAC).
This patch adds compatible string for RZ/G2L and fills up the
ravb_hw_info struct. Function stubs are added which will be used by
gbeth_hw_info and will be filled incrementally.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports network control queue whereas RZ/G2L does not support
it. Add nc_queue to struct ravb_hw_info, so that NC queue is handled
only by R-Car.
This patch also renames ravb_rcar_dmac_init to ravb_dmac_init_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the variable "no_ptp_cfg_active" with "gptp" and
"ptp_cfg_active" with "ccc_gac" to match the HW features.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename "ravb_set_features_rx_csum" function to "ravb_set_features_rcar" and
replace the function pointer "set_rx_csum_feature" with "set_feature".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset support is present on R-Car. Let's support it, if it is
available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E-MAC IP on the R-Car AVB module has different initialization
parameters for RX frame size, duplex settings, different offset
for transfer speed setting and has magic packet detection support
compared to E-MAC on RZ/G2L Gigabit Ethernet module. Factorise
the ravb_emac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC IP on the R-Car AVB module has different initialization
parameters for RCR, TGC, TCCR, RIC0, RIC2, and TIC compared to
DMAC IP on the RZ/G2L Gigabit Ethernet module. Factorise the
ravb_dmac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
