The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 4-tuple NAT offload via PEDIT always overwrites all the 4-tuple
fields even if they had not been explicitly enabled. If any fields in
the 4-tuple are not enabled, then the hardware overwrites the
disabled fields with zeros, instead of ignoring them.
So, add a parser that can translate the enabled 4-tuple PEDIT fields
to one of the NAT mode combinations supported by the hardware and
hence avoid overwriting disabled fields to 0. Any rule with
unsupported NAT mode combination is rejected.
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t4_sge_stop() is only ever called from task context and the in_interrupt()
check is presumably a leftover from copying t3_sge_stop().
Aside of in_interrupt() being deprecated because it's not providing what it
claims to provide, this check would paper over illegitimate callers.
The functions invoked from t4_sge_stop() contain already warnings to catch
invocations from invalid contexts.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the ktls stats were at adapter level, but now changing it
to port level.
Fixes: 62370a4f34 ("cxgb4/chcr: Add ipv6 support and statistics")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing these logs to dynamic debugs. If issue is seen, these
logs can be enabled at run time.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the memory leak in mps during module unload
path by freeing mps reference entries if the list
adpter->mps_ref is not already empty
Fixes: 28b3870578 ("cxgb4: Re-work the logic for mps refcounting")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves complete nic tls offload (kTLS) code from crypto
directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls
directory. nic TLS is made a separate ULD of cxgb4.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ch_ipsec was removed without clearing xfrmdev_ops and netdev
feature(esp-hw-offload). When a recalculation of netdev feature is
triggered by changing tls feature(tls-hw-tx-offload) from user
request, it causes a page fault due to absence of valid xfrmdev_ops.
Fixes: 6dad4e8ab3 ("chcr: Add support for Inline IPSec")
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the correct offset to clear the stale filter hit
bytes counter. Otherwise, the counter starts incrementing
from the stale information, instead of 0.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
cxgb4 does not look for HASHTBLMEMCRCERR and CMDTIDERR
bits in LE_DB_INT_CAUSE register, but these are enabled
in LE_DB_INT_ENABLE. So, add error handlers to LE
interrupt handler to emit a warning or alert message
for hash table mem crc and cmd tid errors
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch seperates inline ipsec functionality from coprocessor
driver chcr. Now inline ipsec is separate ULD, moved from
"drivers/crypto/chelsio/" to "drivers/net/ethernet/chelsio/inline_crypto/ch_ipsec/"
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 filters can occupy up to 4 slots and will exhaust HPFILTER
region much sooner. So, continue searching for free slots in the
HASH or NORMAL filter regions, as long as the rule's priority does
not conflict with existing rules in those regions.
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
Matching IPv6 traffic require allocating their own individual slots
in TCAM. So, fetch additional slots to insert IPv6 rules. Also, fetch
the cumulative stats of all the slots occupied by the Matchall rule.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c8729cac2a ("cxgb4: add ethtool n-tuple filter insertion")
has removed checking control key for determining IP address types
for TC-FLOWER rules, which causes all the rules being inserted to
hardware to become IPv6 rule type always. So, add back the check
to select the correct IP address type to extract and hence fix the
correct rule type being inserted to hardware.
Also, ethtool_rx_flow_key doesn't have any control key and instead
directly sets the IPv4/IPv6 address keys. So, explicitly set the
IP address type for ethtool n-tuple filters to reuse the same code.
Fixes: c8729cac2a ("cxgb4: add ethtool n-tuple filter insertion")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag indicating the selftest to run is a bitmask. So, fix the
check. Also, the selftests will fail if adapter initialization has
not been completed yet. So, add appropriate check and bail sooner.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this test, loopback pkt is created and sent on default queue.
The packet goes until the Multi Port Switch (MPS) just before
the MAC and based on the specified channel number, it either
goes outside the wire on one of the physical ports or looped
back to Rx path by MPS. In this case, we're specifying loopback
channel, instead of physical ports, so the packet gets looped
back to Rx path, instead of getting transmitted on the wire.
v3:
- Modify commit message to include test details.
v2:
- Add only loopback self-test.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of uld_send(), the skb is consumed on all
execution paths except one. Release skb when returning NET_XMIT_DROP.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new infra, this driver is very simple. The check of
adapter->rawf_cnt in cxgb_udp_tunnel_unset_port() is kept from
the old port deletion function but it's dodgy since nothing ever
updates that member once its set during init. Also .set_port
callback always adds the raw mac filter..
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all-mask IP address to Big Endian, instead, for comparison.
Fixes: f286dd8eaa ("cxgb4: use correct type for all-mask IP address comparison")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mirror VI is enabled, replicate various VI config params
enabled on main VI to mirror VI. These include replicating MTU,
promiscuous mode, all-multicast mode, and enabled netdev Rx
feature offloads.
v3:
- Replace mirror VI refcount_t with normal u32 variable.
- Add back calling cxgb4_port_mirror_start() in cxgb_open(), which
was there in v1, but got missed in v2 during refactoring.
v2:
- Simplify the replication code by refactoring t4_set_rxmode()
to handle mirror VI, instead of duplicating the t4_set_rxmode()
calls in multiple places.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mirror VI is enabled, allocate the mirror Rxqs and setup the
mirror VI RSS table. The mirror Rxqs are allocated/freed when
the mirror VI is created/destroyed or when underlying port is
brought up/down, respectively.
v3:
- Replace mirror VI refcount_t with normal u32 variable.
v2:
- Use mutex to protect all mirror VI data, instead of just
mirror Rxqs.
- Remove the un-needed mirror Rxq mutex.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mirror Virtual Interface (VI) support to receive all ingress
mirror traffic from the underlying device. The mirror VI is
created dynamically, if the TC-MATCHALL rule has a corresponding
mirror action. Also request MSI-X vectors needed for the mirror VI
Rxqs. If no vectors are available, then disable mirror VI support.
v3:
- Replace mirror VI refcount_t with normal u32 variable.
v2:
- Add mutex to protect all mirror VI data, instead of just
mirror Rxqs.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_prep_fw goto bye tag with positive return value when something
bad happened and which can not free resource in adap_init0.
so fix it to return negative value.
Fixes: 16e47624e7 ("cxgb4: Add new scheme to update T4/T5 firmware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all arrays related to device dump in header file to C file.
Also, move the function that shares the arrays to the same C file.
Fixes following warnings reported by make W=1 in several places:
cudbg_entity.h:513:18: warning: 't6_hma_ireg_array' defined but not
used [-Wunused-const-variable=]
513 | static const u32 t6_hma_ireg_array[][IREG_NUM_ELEM] = {
Fixes: a7975a2f9a ("cxgb4: collect register dump")
Fixes: 17b332f480 ("cxgb4: add support to read serial flash")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to on-chip memory for flashing PHY firmware must always
be synchronized. So, ensure the callers take on-chip memory lock.
Also fixes following sparse warning:
sge.c:1641:26: warning: context imbalance in 't4_load_phy_fw' -
different lock contexts for basic block
Fixes: 01b6961410 ("cxgb4: Add PHY firmware support for T420-BT cards")
Fixes: 4ee339e1e9 ("cxgb4: add support to flash PHY image")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update several kernel-doc line comments to fix warnings reported by
make W=1.
Fixes following class of warnings reported by make W=1 in several
places:
l2t.c:616: warning: Cannot understand * @dev: net_device pointer
t4_hw.c:3175: warning: Function parameter or member 'adap' not
described in 't4_get_exprom_version'
t4_hw.c:3175: warning: Excess function parameter 'adapter' description
in 't4_get_exprom_version'
Fixes: 56d36be4dd ("cxgb4: Add HW and FW support code")
Fixes: fd3a47900b ("cxgb4: Add packet queues and packet DMA code")
Fixes: 26f7cbc0a5 ("cxgb4: Don't attempt to upgrade T4 firmware when cxgb4 will end up as a slave")
Fixes: 793dad94e7 ("RDMA/cxgb4: Fix bug for active and passive LE hash collision path")
Fixes: ba3f8cd55f ("cxgb4: Add support in cxgb4 to get expansion rom version via ethtool")
Fixes: f7502659ce ("cxgb4: Add API to alloc l2t entry; also update existing ones")
Fixes: ddc7740d9a ("cxgb4: Decode link down reason code obtained from firmware")
Fixes: 193c4c2845 ("cxgb4: Update T6 Buffer Group and Channel Mappings")
Fixes: 8f46d46715 ("cxgb4: Use Firmware params to get buffer-group map")
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Fixes: 9c33e4208b ("cxgb4: Add PTP Hardware Clock (PHC) support")
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Fixes: 5ccf9d0496 ("cxgb4: update API for TP indirect register access")
Fixes: 3bdb376e69 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Fixes: 736c3b9447 ("cxgb4: collect egress and ingress SGE queue contexts")
Fixes: f56ec6766d ("cxgb4: Add support for ethtool i2c dump")
Fixes: 9d5fd927d2 ("cxgb4/cxgb4vf: add support for ndo_set_vf_vlan")
Fixes: 98f3697f8d ("cxgb4: add tc flower match support for tunnel VNI")
Fixes: 02d805dc5f ("cxgb4: use new fw interface to get the VIN and smt index")
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the set but unused variable when DCB is disabled. Instead,
do the calculation directly inline.
Fixes following warning in make W=1:
cxgb4_main.c: In function 'cfg_queues':
cxgb4_main.c:5380:29: warning: variable 'n1g' set but not used
[-Wunused-but-set-variable]
u32 i, n10g = 0, qidx = 0, n1g = 0;
^
Fixes: 116ca924ae ("cxgb4: fix checks for max queues to allocate")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DCB version string array extern to header file.
Fixes following sparse warning:
cxgb4_dcb.c:13:12: warning: symbol 'dcb_ver_array' was not declared.
Should it be static?
Fixes: ebddd97afb ("cxgb4: add support to display DCB info")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum field in IPv4 header is in __sum16 and ip_fast_csum()
also returns __sum16. So, no need to cast it to u16.
Fixes following sparse warning:
sge.c:1539:47: warning: cast from restricted __sum16
sge.c:1539:44: warning: incorrect type in assignment (different base types)
sge.c:1539:44: expected restricted __sum16 [usertype] check
sge.c:1539:44: got unsigned short [usertype]
Fixes: d0a1299c6b ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data in destination buffer is expected to be be parsed in big
endian. So, use the right context.
Fixes following sparse warning:
cudbg_lib.c:2041:44: warning: incorrect type in assignment (different
base types)
cudbg_lib.c:2041:44: expected unsigned long long [usertype]
cudbg_lib.c:2041:44: got restricted __be64 [usertype]
Fixes: 736c3b9447 ("cxgb4: collect egress and ingress SGE queue contexts")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct type to check for all-mask exact match IP addresses.
Fixes following sparse warnings due to big endian value checks
against 0xffffffff in is_addr_all_mask():
cxgb4_filter.c:977:25: warning: restricted __be32 degrades to integer
cxgb4_filter.c:983:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:984:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:985:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:986:37: warning: restricted __be32 degrades to integer
Fixes: 3eb8b62d5a ("cxgb4: add support to create hash-filters via tc-flower offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The source and destination L4 ports in filter offload need to be
in CPU endian. They will finally be converted to Big Endian after
all operations are done and before giving them to hardware. The
L4 ports for NAT are expected to be passed as a byte stream TCB.
So, treat them as such.
Fixes following sparse warnings in several places:
cxgb4_tc_flower.c:159:33: warning: cast from restricted __be16
cxgb4_tc_flower.c:159:33: warning: incorrect type in argument 1 (different
base types)
cxgb4_tc_flower.c:159:33: expected unsigned short [usertype] val
cxgb4_tc_flower.c:159:33: got restricted __be16 [usertype] dst
Fixes: dca4faeb81 ("cxgb4: Add LE hash collision bug fix path in LLD driver")
Fixes: 62488e4b53 ("cxgb4: add basic tc flower offload support")
Fixes: 557ccbf9df ("cxgb4: add tc flower support for L3/L4 rewrite")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC-U32 passes all keys values and masks in __be32 format. The parser
already expects this and hence pass the value and masks in __be32
natively to the parser.
Fixes following sparse warnings in several places:
cxgb4_tc_u32.c:57:21: warning: incorrect type in assignment (different base
types)
cxgb4_tc_u32.c:57:21: expected unsigned int [usertype] val
cxgb4_tc_u32.c:57:21: got restricted __be32 [usertype] val
cxgb4_tc_u32_parse.h:48:24: warning: cast to restricted __be32
Fixes: 2e8aad7bf2 ("cxgb4: add parser to translate u32 filters to internal spec")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use get_unaligned_be64() to fetch the timestamp needed for ns_to_ktime()
conversion.
Fixes following sparse warning:
sge.c:3282:43: warning: cast to restricted __be64
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for whether PTP is enabled or not at the caller and perform
locking/unlocking at the caller.
Fixes following sparse warning:
sge.c:1641:26: warning: context imbalance in 'cxgb4_eth_xmit' -
different lock contexts for basic block
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code handling L2T ARP failures to the only caller.
Fixes following sparse warning:
skbuff.h:2091:29: warning: context imbalance in
'handle_failed_resolution' - unexpected unlock
Fixes: 749cb5fe48 ("cxgb4: Replace arpq_head/arpq_tail with SKB double link-list code")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for queue action to steer Rx traffic
hitting the flows to specified Rxq.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the requested ethtool n-tuple filters by
translating them from hardware spec to ethtool n-tuple spec.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to delete ethtool n-tuple filter. Fetch the appropriate
filter region (HPFILTER, HASH, NORMAL) in which the filter exists,
and delete it from the respective region, accordingly.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to parse and insert ethtool n-tuple filters.
Translate n-tuple spec to flow spec and use the existing tc-flower
offload infra to insert ethtool n-tuple filters.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and manage resources required for ethtool n-tuple filters.
Also fetch the HASH filter region size and calculate nhash entries.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to dump flash memory via
ethtool --get-dump
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update set_flash to flash boot cfg image to flash region
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update set_flash to flash boot image to flash region
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update set_flash to flash PHY image to flash region
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chelsio adapter contains different flash regions and each
region is used by different binary files. This patch adds
support to flash images like PHY firmware, boot and boot config
using ethtool -f N.
The N value mapping is as follows.
N = 0 : Parse image and decide which region to flash
N = 1 : Firmware
N = 2 : PHY firmware
N = 3 : boot image
N = 4 : boot cfg
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kfree(buf) in blocked_fl_read() because the memory is allocated with
kzalloc(). Use kfree(t) in blocked_fl_write() because the memory is
allocated with kcalloc().
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_uld_in_use() is used only by cxgb4_ktls_det_feature() which
is under CONFIG_CHELSIO_TLS_DEVICE macro.
Fixes: a3ac249a1a ("cxgb4/chcr: Enable ktls settings at run time")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current design enables ktls setting from start, which is not
efficient. Now the feature will be enabled when user demands
TLS offload on any interface.
v1->v2:
- taking ULD module refcount till any single connection exists.
- taking rtnl_lock() before clearing tls_devops.
v2->v3:
- cxgb4 is now registering to tlsdev_ops.
- module refcount inc/dec in chcr.
- refcount is only for connections.
- removed new code from cxgb_set_feature().
v3->v4:
- fixed warning message.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon adapter hotplug, cxgb4 registers ULD devices for all the ULDs that
are already loaded, ensuring that ULD's can enumerate the hotplugged
adapter without reloading the ULD.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework and add support for dumping EOTID software context used by
TC-MQPRIO. Also track number of EOTIDs in use.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each traffic class, firmware handles up to 4 * MTU amount of data
per burst cycle. Under heavy load, this small buffer size is a
bottleneck when buffering large TSO packets in <= 1500 MTU case.
Increase the burst buffer size to 8 * MTU when supported.
Also, keep the driver's traffic class configuration API similar to
the firmware API counterpart.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request credit update for every half credits consumed, including
the current request. Also, avoid re-trying to post packets when there
are no credits left. The credit update reply via interrupt will
eventually restore the credits and will invoke the Tx path again.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate headers which are included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports a warning at service_ofldq()
warning: context imbalance in service_ofldq() - unexpected unlock
The root cause is the missing annotation at service_ofldq()
Add the missing __must_hold(&q->sendq.lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy load, the EOTID termination FLOWC request fails to get
enqueued to the end of the Tx ring due to lack of credits. This
results in EOTID leak.
When disabling TC-MQPRIO offload, the link is already brought down
to cleanup EOTIDs. So, flush any pending enqueued skbs that can't be
sent outside the wire, to make room for FLOWC request. Also, move the
FLOWC descriptor consumption logic closer to when the FLOWC request is
actually posted to hardware.
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.
Fixes: a1c69520f7 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208b ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_update_mac_filt() earlier requests firmware to add a new MAC
address into MPS TCAM. The MPS TCAM index returned by firmware is
stored in pi->xact_addr_filt. However, the saved MPS TCAM index gets
overwritten again with the return value of cxgb4_update_mac_filt(),
which is wrong.
When trying to update to another MAC address later, the wrong MPS TCAM
index is sent to firmware, which causes firmware to return error,
because it's not the same MPS TCAM index that firmware had sent
earlier to driver.
So, fix by removing the wrong overwrite being done after call to
cxgb4_update_mac_filt().
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Included nic tls statistics in ethtool stats.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support to catch any bits set in SGE_INT_CAUSE5 for Parity Errors.
F_ERR_T_RXCRC flag is used to ignore that particular bit as it is not considered as fatal.
So, we clear out the bit before looking for error.
This patch now read and report separately all three registers(Cause1, Cause2, Cause5).
Also, checks for errors if any.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c: In function cxgb4_get_free_ftid:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c:547:23:
warning: variable tab set but not used [-Wunused-but-set-variable]
commit 8d174351f2 ("cxgb4: rework TC filter rule insertion across regions")
involved this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).
Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.
So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in remove filters entry
failure for cxgb4 unload path. This patch fix that.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more T5/T6 registers to be collected in register dump:
1. MPS register range 0x9810 to 0x9864 and 0xd000 to 0xd004.
2. NCSI register range 0x1a114 to 0x1a130 and 0x1a138 to 0x1a1c4.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding ipv6 support and ktls related statistics.
v1->v2:
- added blank lines at 2 places.
v3->v4:
- Replaced atomic_t with atomic64_t
- added few necessary stat counters.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added tx handling in this patch. This includes handling of segments
contain single complete record.
v1->v2:
- chcr_write_cpl_set_tcb_ulp is added in this patch.
v3->v4:
- mss calculation logic.
- replaced kfree_skb with dev_kfree_skb_any.
- corrected error message reported by kbuild test robot <lkp@intel.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of this patch generated and saved crypto keys, handled HW
response of act_open_req and set_tcb_req. Defined connection state
update.
v1->v2:
- optimized tcb update using control queue.
- state machine handling when earlier states received.
v2->v3:
- Added one empty line after function declaration.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new macro is defined to enable ktls tx offload support on Chelsio
T6 adapter. And if this macro is enabled, cxgb4 will send mailbox to
enable or disable ktls settings on HW.
In chcr, enabled tx offload flag in netdev and registered tls_dev_add
and tls_dev_del.
v1->v2:
- mark tcb state to close in tls_dev_del.
- u_ctx is now picked from adapter structure.
- clear atid in case of failure.
- corrected ULP_CRYPTO_KTLS_INLINE value.
v2->v3:
- add empty line after variable declaration.
- local variable declaration in reverse christmas tree ordering.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.
Fixes: 5952dde723 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set N/A if FW is not available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the code related to various versions: driver and module.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added debugfs entry to show the tls stats.
Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd6 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8e ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in connection failures for
ULDs.
So, fix all related code to properly recalculate the TID start index
based on whether high priority filters are enabled or not.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c219399988 ("cxgb4: add support for high priority filters")
has missed considering high priority region calculation in some code
paths. This patch fixes them.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 has a separate region known as high priority filter region
that allows classifying packets going through ULD path. So,
query firmware for HPFILTER resources and enable the high
priority offload filter support when it is available.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement and export UDP segmentation offload (USO) support for both
NIC and MQPRIO QoS offload Tx path. Update appropriate logic in Tx to
parse GSO info in skb and configure FW_ETH_TX_EO_WR request needed to
perform USO.
v2:
- Remove inline keyword from write_eo_udp_wr() in sge.c. Let the
compiler decide.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The FW_ETH_TX_EO_WR used for sending UDP Segmentation Offload (USO)
requests expects the headers to be part of the descriptor and the
payload to be part of the SGL containing the DMA mapped addresses.
Hence, the DMA address in the first entry of the SGL can start after
the packet headers. Currently, unmap_sgl() tries to unmap from this
wrong offset, instead of the originally mapped DMA address.
So, use existing unmap_skb() instead, which takes originally saved DMA
addresses as input. Update all necessary Tx paths to save the original
DMA addresses, so that unmap_skb() can unmap them properly.
v2:
- No change.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add TC-MATCHALL classifier ingress offload support. The same actions
supported by existing TC-FLOWER offload can be applied to all incoming
traffic on the underlying interface.
Ensure the rule priority doesn't conflict with existing rules in the
TCAM. Only 1 ingress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually.
v3:
- No change.
v2:
- Removed logic to fetch free index from end of TCAM. Must maintain
same ordering as in kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only offload rule if it satisfies both of the following conditions:
1. The immediate previous rule has priority <= current rule's priority.
2. The immediate next rule has priority >= current rule's priority.
Also rework free entry fetch logic to search from end of TCAM, instead
of beginning, because higher indices have lower priority than lower
indices. This is similar to how TC auto generates priority values.
v5:
- Fixed commit message and comment to include comparison for equal
priority.
v4:
- Patch added in this version.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
$ tc qdisc add dev enp2s0f4 clsact
$ tc filter add dev enp2s0f4 egress matchall skip_sw \
action police rate 1Gbit burst 8Kbit
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semicolon is not required at the end of switch block. So, remove it.
Addresses coccinelle warning:
drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon
Fixes: 4846d5330d ("cxgb4: add Tx and Rx path for ETHOFLD traffic")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ret" is zero or possibly uninitialized on this error path. It
should be a negative error code instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c:242:6: warning: symbol 'cxgb4_mqprio_free_hw_resources' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework SCHED API to allow offloading TC-MQPRIO QoS configuration.
The existing QUEUE based rate limiting throttles all queues sharing
a traffic class, to the specified max rate limit value. So, if
multiple queues share a traffic class, then all the queues get
the aggregate specified max rate limit.
So, introduce the new FLOWC based rate limiting, where multiple
queues can share a traffic class with each queue getting its own
individual specified max rate limit.
For example, if 2 queues are bound to class 0, which is rate limited
to 1 Gbps, then 2 queues using QUEUE based rate limiting, get the
aggregate output of 1 Gbps only. In FLOWC based rate limiting, each
queue gets its own output of max 1 Gbps each; i.e. 2 queues * 1 Gbps
rate limit = 2 Gbps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement Tx path for traffic flowing through software EOSW_TXQ
and EOHW_TXQ. Since multiple EOSW_TXQ can post packets to a single
EOHW_TXQ, protect the hardware queue with necessary spinlock. Also,
move common code used to generate TSO work request to a common
function.
Implement Rx path to handle Tx completions for successfully
transmitted packets.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring and managing ETHOFLD hardware queues.
Keep the queue count and MSI-X allocation scheme same as NIC queues.
ETHOFLD hardware queues are dynamically allocated/destroyed as
TC-MQPRIO Qdisc offload is enabled/disabled on the corresponding
interface, respectively.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for validation and configuration of TC-MQPRIO Qdisc
offload. Also, add support to manage EOSW_TXQ, which have 1-to-1
mapping with EOTIDs, and expose them to network stack.
Move common skb validation in Tx path to a separate function and
add minimal Tx path for ETHOFLD. Update Tx queue selection to return
normal NIC Txq to send traffic pattern that can't go through ETHOFLD
Tx path.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify queue configuration and MSI-X allocation logic. Use a single
MSI-X information table for both NIC and ULDs. Remove hard-coded
MSI-X indices for firmware event queue and non data interrupts.
Instead, use the MSI-X bitmap to obtain a free MSI-X index
dynamically. Save each Rxq's index into the MSI-X information table,
within the Rxq structures themselves, for easier cleanup.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QoS offload needs Ethernet Offload (ETHOFLD) resources present in the
NIC. These resources are shared with other ULDs. So, query firmware
for the available number of traffic classes, as well as, start and
end indices (EOTID) of the ETHOFLD region.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use '__skb_queue_purge()' instead of re-implementing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release resources when attaching to ULD fail. Otherwise, data
mismatch is seen between LLD and ULD later on, which lead to
kernel panic when accessing resources that should not even
exist in the first place.
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For adapters which support the SGE Doorbell Queue Timer facility,
we configured the Ethernet TX Queues to send CIDX Updates to the
Associated Ethernet RX Response Queue with CPL_SGE_EGR_UPDATE
messages to allow us to respond more quickly to the CIDX Updates.
But, this was adding load to PCIe Link RX bandwidth and,
potentially, resulting in higher CPU Interrupt load.
This patch requests the HW to deliver the CIDX updates to the TX
queue status page rather than generating an ingress queue message
(as an interrupt). With this patch, the load on RX bandwidth is
reduced and a substantial improvement in BW is noticed at lower
IO sizes.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "chip" variable is an enum, and it's treated as unsigned int by GCC
in this context so the error handling isn't triggered.
Fixes: e8d452923a ("cxgb4: clean up init_one")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix several spelling typos in comments in t4_hw.c.
Signed-off-by: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails,
leading to a memory leak bug. To fix this issue, free t before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
If a debugfs call fails, it will properly warn in the syslog, there's no
need for all individual drivers to also print a message, so that is one
more reason to not care about checking the return values.
Cc: Vishal Kulkarni <vishal@chelsio.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All refcount operations are protected by spinlocks now.
Then the atomic counter can be replaced by a normal int.
This patch depends on PATCH 1/2.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atomic_dec_and_test() is not safe because it is
outside of locks.
Move the locks of t4_smte_free() to its caller,
cxgb4_smt_release() to protect the atomic decrement.
Fixes: 3bdb376e69 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
allocate_flower_entry does not check for allocation success, but tries
to deref the result. I only moved the spin_lock under null check, because
the caller is checking allocation's status at line 652.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cudbg_collect_mem_region() and cudbg_read_fw_mem() both use several
hundred kilobytes of kernel stack space. One gets inlined into the other,
which causes the stack usage to be combined beyond the warning limit
when building with clang:
drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c:1057:12: error: stack frame size of 1244 bytes in function 'cudbg_collect_mem_region' [-Werror,-Wframe-larger-than=]
Restructuring cudbg_collect_mem_region() lets clang do the same
optimization that gcc does and reuse the stack slots as it can
see that the large variables are never used together.
A better fix might be to avoid using cudbg_meminfo on the stack
altogether, but that requires a larger rewrite.
Fixes: a1c69520f7 ("cxgb4: collect MC memory dump")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.
This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.
This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.
This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.
There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds reference counting support for
alloc/free mac filters
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for cxgb4 change mac path
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for raw mac filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove existing mps refcounting code which was
added only for encap filters and add necessary
data structures/functions to support mps reference
counting for all the mac filters. Also add wrapper
functions for allocating and freeing encap mac
filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page pods are used for direct data placement, this patch
enables eDRAM page pods if firmware supports this feature.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spread initial IRQ affinity hints across the device node CPUs,
for nic queue and uld queue IRQs, to load balance and avoid
all interrupts on CPU0.
Signed-off-by: Nirranjan Kirubaharan <nirranjan@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope [that] it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 57 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.515993066@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14:
warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2391b0030e which has
introduced regression. Now SGE's BAR2 Doorbell/GTS Page Size is
interpreted correctly in the firmware itself by using actual host
page size. Hence previous commit needs to be reverted.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN flows never get offloaded unless ivlan_vld is set in filter spec.
It's not compulsory for vlan_ethtype to be set.
So, always enable ivlan_vld bit for offloading VLAN flows regardless of
vlan_ethtype is set or not.
Fixes: ad9af3e09c (cxgb4: add tc flower match support for vlan)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for validating hardware filter spec configured in firmware
before offloading exact match flows.
Use the new fw api FW_PARAM_DEV_FILTER_MODE_MASK to read the filter mode
and mask from firmware. If the api isn't supported, then fall-back to
older way of reading just the mode from indirect register.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver unload, hash/TCAM filter deletion doesn't wait for
completion.This patch deletes all the filters with completion before
clearing the resources.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hash filter programming, driver needs to return ENOSPC error
intead of EAGAIN when TCAM is full.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advertises Forward Error Correction in ethtool
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.23.3.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
# define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x)))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
return buf_size;
^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
BUG_ON(1);
^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^
drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
int buf_size;
^
= 0
Use BUG() here to create simpler code that clang understands
correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been a slightly more active cycle than normal with ongoing core
changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5 On-Demand-Paging MR
feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and fixing
the various unregistration race conditions in rxe's unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
* Drivers should not assume umem SGLs are in PAGE_SIZE chunks
* ucontext is accessed via udata not other means
* Start to make the core code responsible for object memory
allocation
* Drivers should convert struct device to struct ib_device
via a helper
* Drivers have more tools to avoid use after unregister problems
-----BEGIN PGP SIGNATURE-----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=p12E
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a slightly more active cycle than normal with ongoing
core changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5
On-Demand-Paging MR feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and
fixing the various unregistration race conditions in rxe's
unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
- drivers should not assume umem SGLs are in PAGE_SIZE chunks
- ucontext is accessed via udata not other means
- start to make the core code responsible for object memory
allocation
- drivers should convert struct device to struct ib_device via a
helper
- drivers have more tools to avoid use after unregister problems"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (280 commits)
net/mlx5: ODP support for XRC transport is not enabled by default in FW
IB/hfi1: Close race condition on user context disable and close
RDMA/umem: Revert broken 'off by one' fix
RDMA/umem: minor bug fix in error handling path
RDMA/hns: Use GFP_ATOMIC in hns_roce_v2_modify_qp
cxgb4: kfree mhp after the debug print
IB/rdmavt: Fix concurrency panics in QP post_send and modify to error
IB/rdmavt: Fix loopback send with invalidate ordering
IB/iser: Fix dma_nents type definition
IB/mlx5: Set correct write permissions for implicit ODP MR
bnxt_re: Clean cq for kernel consumers only
RDMA/uverbs: Don't do double free of allocated PD
RDMA: Handle ucontext allocations by IB/core
RDMA/core: Fix a WARN() message
bnxt_re: fix the regression due to changes in alloc_pbl
IB/mlx4: Increase the timeout for CM cache
IB/core: Abort page fault handler silently during owning process exit
IB/mlx5: Validate correct PD before prefetch MR
IB/mlx5: Protect against prefetch of invalid MR
RDMA/uverbs: Store PR pointer before it is overwritten
...
Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ndo_set_vf_link_state to control the link states associated
with the virtual interfaces.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 adapters support outer UDP checksum offload for
encapsulated packets, hence enabling netdev feature flag
NETIF_F_GSO_UDP_TUNNEL_CSUM.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is done by cxgb4/cxgb4vf. Hence set NETIF_F_GRO flag for
both cxgb4/cxgb4vf.
Cleaned up VLAN netdev features in cxgb4vf. Also fixed
NETIF_F_HIGHDMA being set unconditionally for vlan netdev
features.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are rare cases where a PL_INT_CAUSE bit may end up getting
set when the corresponding PL_INT_ENABLE bit isn't set.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the sge_host_page_size field to ULDs via cxgb4_lld_info, so that
iw_cxgb4 can make use of this in calculating the correct qp/cq mask.
Fixes: 2391b0030e ("cxgb4: Remove SGE_HOST_PAGE_SIZE dependency on page size")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch gets/sets SGE Doorbell Queue timer ticks via ethtool
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 introduced a Timer Mechanism in SGE called the
SGE Doorbell Queue Timer. With this we can now configure
TX Queues to get CIDX Updates when:
Time(CIDX == PIDX) >= Timer
Previously we rely on TX Queue Status Page updates by hardware
for DMA completions. This will make Hardware/Firmware actually
deliver the CIDX Updates as Ingress Queue messages with
commensurate Interrupts.
So we now have a new RX Path component for processing CIDX Updates
and reclaiming TX Descriptors faster.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the tcb flags and structures needed for querying tcb
information.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Change t4fw_version.h to update latest firmware version
number to 1.22.9.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is
finding the size of a structure that has a zero-sized array at
the end, along with memory for some number of elements for that
array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is
finding the size of a structure that has a zero-sized array at
the end, along with memory for some number of elements for that
array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
