There are three boolean variable which were not initialized and later
being used in the code.
Signed-off-by: Yacov Simhony <ysimhony@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several cases where validate() would return bogus supported
modes with unusual combinations of interfaces and capabilities. For
example, if state->interface was 10GBASER and the macb had HIGH_SPEED
and PCS but not GIGABIT MODE, then 10/100 modes would be set anyway. In
another case, SGMII could be enabled even if the mac was not a GEM
(despite this being checked for later on in mac_config()). These
inconsistencies make it difficult to refactor this function cleanly.
There is still the open question of what exactly the requirements for
SGMII and 10GBASER are, and what SGMII actually supports. If someone
from Cadence (or anyone else with access to the GEM/MACB datasheet)
could comment on this, it would be greatly appreciated. In particular,
what is supported by Cadence vs. vendor extension/limitation?
To address this, the current logic is split into three parts. First, we
determine what we support, then we eliminate unsupported interfaces, and
finally we set the appropriate link modes. There is still some cruft
related to NA, but this can be removed in a future patch.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Parshuram Thombare <pthombar@cadence.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211112190400.1937855-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4d98bb0d7e ("net: macb: Use mdio child node for MDIO bus if it
exists") added code to detect if a 'mdio' child node exists to the macb
driver. Ths added code does, however, not actually check if the child node
exists, but if the parent node exists. This results in errors such as
macb 10090000.ethernet eth0: Could not attach PHY (-19)
if there is no 'mdio' child node. Fix the code to actually check for
the child node.
Fixes: 4d98bb0d7e ("net: macb: Use mdio child node for MDIO bus if it exists")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211026173950.353636-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This allows explicitly specifying which children are present on the mdio
bus. Additionally, it allows for non-phy MDIO devices on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update three drivers to use the new phylink_set_10g_modes() helper:
Cadence macb, Freescale DPAA2 and Marvell PP2.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb PTP support currently implements the `gettime64` callback to allow
to retrieve the hardware clock time. Update the implementation to provide
the `gettimex64` callback instead.
The difference between the two is that with `gettime64` a snapshot of the
system clock is taken before and after invoking the callback. Whereas
`gettimex64` expects the callback itself to take the snapshots.
To get the time from the macb Ethernet core multiple register accesses have
to be done. Only one of which will happen at the time reported by the
function. This leads to a non-symmetric delay and adds a slight offset
between the hardware and system clock time when using the `gettime64`
method. This offset can be a few 100 nanoseconds. Switching to the
`gettimex64` method allows for a more precise correlation of the hardware
and system clocks and results in a lower offset between the two.
On a Xilinx ZynqMP system `phc2sys` reports a delay of 1120 ns before and
300 ns after the patch. With the latter being mostly symmetric.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both MAC IPs available on SAMA7G5 support MII on RGMII feature.
Enable these by adding proper capability to proper macb_config
objects.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cadence IP has option to enable MII support on RGMII interface. This
could be selected though bit 28 of network control register. This option
is not enabled on all the IP versions thus add a software capability to
be selected by the proper implementation of this IP.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align for OSSMODE offset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for SRTSM bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff7 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/cadence/macb_pci.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/net/ethernet/cadence/macb_ptp.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable queue is set to bp->queues but these values is not used as it
is overwritten later on, hence redundant assignment can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/cadence/macb_main.c:4919:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/cadence/macb_main.c:4832:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a14d273ba1 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba1 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba1 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restore CMP screener registers on resume path.
Fixes: c1e85c6ce5 ("net: macb: save/restore the remaining registers and features")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, e.g., the ZynqMP, devm_clk_get can return
-EPROBE_DEFER if the clock controller, which is implemented in firmware,
has not been probed yet.
As clk_init is only called during probe, use dev_err_probe to simplify
the error message and hide it for -EPROBE_DEFER.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link configuration in SGMII mode, it's not really
sensible to have auto-negotiation enabled since the link settings are
fixed by definition. In other configurations, such as an SGMII
connection to a PHY, it should generally be enabled.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link configuration with GEM in SGMII mode, such as
for a chip-to-chip interconnect, the link state was always showing as
established regardless of the actual connectivity state. We can monitor
the pcs_link_state bit in the Network Status register to determine
whether the PCS link state is actually up.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no usrio config defined for default gem config leading to
a kernel panic devices that don't define a data. This issue can be
reprdouced with microchip polar fire soc where compatible string
is defined as "cdns,macb".
Fixes: edac63861d ("add userio bits as platform configuration")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MII interface is used, the PHY is the clock master, thus don't
set the clock rate. On Zynq-7000, this will prevent the following
warning:
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210120194303.28268-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new flag MACB_CAPS_CLK_HW_CHG was added and all callers of
macb_set_tx_clk were gated on the presence of this flag.
- if (!clk)
+ if (!bp->tx_clk || !(bp->caps & MACB_CAPS_CLK_HW_CHG))
However the flag was not added to anything other than the new
sama7g5_gem, turning that function call into a no op for all other
systems. This breaks the networking on Zynq.
The commit message adding this states: a new capability so that
macb_set_tx_clock() to not be called for IPs having this
capability
This strongly implies that present of the flag was intended to skip
the function not absence of the flag. Update the if statement to
this effect, which repairs the existing users.
Fixes: daafa1d33c ("net: macb: add capability to not set the clock rate")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210104103802.13091-1-ckeepax@opensource.cirrus.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 0a4e9ce17b.
The code was developed and tested on an MSC313E SoC, which seems to be
half-way between the AT91RM9200 and the AT91SAM9260 in that it supports
both the 2-descriptors mode and a Tx ring.
It turns out that after the code was merged I could notice that the
controller would sometimes lock up, and only when dealing with sustained
bidirectional transfers, in which case it would report a Tx overrun
condition right after having reported being ready, and will stop sending
even after the status is cleared (a down/up cycle fixes it though).
After adding lots of traces I couldn't spot a sequence pattern allowing
to predict that this situation would happen. The chip comes with no
documentation and other bits are often reported with no conclusive
pattern either.
It is possible that my change is wrong just like it is possible that
the controller on the chip is bogus or at least unpredictable based on
existing docs from other chips. I do not have an RM9200 at hand to test
at the moment and a few tests run on a more recent 9G20 indicate that
this code path cannot be used there to test the code on a 3rd platform.
Since the MSC313E works fine in the single-descriptor mode, and that
people using the old RM9200 very likely favor stability over performance,
better revert this patch until we can test it on the original platform
this part of the driver was written for. Note that the reverted patch
was actually tested on MSC313E.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/netdev/20201206092041.GA10646@1wt.eu/
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SAMA7G5 10/100Mbps interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unprepare clocks in case of any failure in fu540_c000_clk_init().
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to disable all macb clocks.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SAMA7G5's ethernet IPs TX clock could be provided by its generic clock or
by the external clock provided by the PHY. The internal IP logic divides
properly this clock depending on the link speed. The patch adds a new
capability so that macb_set_tx_clock() to not be called for IPs having
this capability (the clock rate, in case of generic clock, is set at the
boot time via device tree and the driver only enables it).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary for SAMA7G5 as it uses different values for
PHY interface and also introduces hdfctlen bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In my test setup, I had a SAMA5D27 device configured with ip forwarding, and
second device with usb ethernet (r8152) sending ICMP packets. If the packet
was larger than about 220 bytes, the SAMA5 device would "oops" with the
following trace:
kernel BUG at net/core/skbuff.c:1863!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in: xt_MASQUERADE ppp_async ppp_generic slhc iptable_nat xt_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 can_raw can bridge stp llc ipt_REJECT nf_reject_ipv4 sd_mod cdc_ether usbnet usb_storage r8152 scsi_mod mii o
ption usb_wwan usbserial micrel macb at91_sama5d2_adc phylink gpio_sama5d2_piobu m_can_platform m_can industrialio_triggered_buffer kfifo_buf of_mdio can_dev fixed_phy sdhci_of_at91 sdhci_pltfm libphy sdhci mmc_core ohci_at91 ehci_atmel o
hci_hcd iio_rescale industrialio sch_fq_codel spidev prox2_hal(O)
CPU: 0 PID: 0 Comm: swapper Tainted: G O 5.9.1-prox2+ #1
Hardware name: Atmel SAMA5
PC is at skb_put+0x3c/0x50
LR is at macb_start_xmit+0x134/0xad0 [macb]
pc : [<c05258cc>] lr : [<bf0ea5b8>] psr: 20070113
sp : c0d01a60 ip : c07232c0 fp : c4250000
r10: c0d03cc8 r9 : 00000000 r8 : c0d038c0
r7 : 00000000 r6 : 00000008 r5 : c59b66c0 r4 : 0000002a
r3 : 8f659eff r2 : c59e9eea r1 : 00000001 r0 : c59b66c0
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c53c7d Table: 2640c059 DAC: 00000051
Process swapper (pid: 0, stack limit = 0x75002d81)
<snipped stack>
[<c05258cc>] (skb_put) from [<bf0ea5b8>] (macb_start_xmit+0x134/0xad0 [macb])
[<bf0ea5b8>] (macb_start_xmit [macb]) from [<c053e504>] (dev_hard_start_xmit+0x90/0x11c)
[<c053e504>] (dev_hard_start_xmit) from [<c0571180>] (sch_direct_xmit+0x124/0x260)
[<c0571180>] (sch_direct_xmit) from [<c053eae4>] (__dev_queue_xmit+0x4b0/0x6d0)
[<c053eae4>] (__dev_queue_xmit) from [<c05a5650>] (ip_finish_output2+0x350/0x580)
[<c05a5650>] (ip_finish_output2) from [<c05a7e24>] (ip_output+0xb4/0x13c)
[<c05a7e24>] (ip_output) from [<c05a39d0>] (ip_forward+0x474/0x500)
[<c05a39d0>] (ip_forward) from [<c05a13d8>] (ip_sublist_rcv_finish+0x3c/0x50)
[<c05a13d8>] (ip_sublist_rcv_finish) from [<c05a19b8>] (ip_sublist_rcv+0x11c/0x188)
[<c05a19b8>] (ip_sublist_rcv) from [<c05a2494>] (ip_list_rcv+0xf8/0x124)
[<c05a2494>] (ip_list_rcv) from [<c05403c4>] (__netif_receive_skb_list_core+0x1a0/0x20c)
[<c05403c4>] (__netif_receive_skb_list_core) from [<c05405c4>] (netif_receive_skb_list_internal+0x194/0x230)
[<c05405c4>] (netif_receive_skb_list_internal) from [<c0540684>] (gro_normal_list.part.0+0x14/0x28)
[<c0540684>] (gro_normal_list.part.0) from [<c0541280>] (napi_complete_done+0x16c/0x210)
[<c0541280>] (napi_complete_done) from [<bf14c1c0>] (r8152_poll+0x684/0x708 [r8152])
[<bf14c1c0>] (r8152_poll [r8152]) from [<c0541424>] (net_rx_action+0x100/0x328)
[<c0541424>] (net_rx_action) from [<c01012ec>] (__do_softirq+0xec/0x274)
[<c01012ec>] (__do_softirq) from [<c012d6d4>] (irq_exit+0xcc/0xd0)
[<c012d6d4>] (irq_exit) from [<c0160960>] (__handle_domain_irq+0x58/0xa4)
[<c0160960>] (__handle_domain_irq) from [<c0100b0c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0d01ef0 to 0xc0d01f38)
1ee0: 00000000 0000003d 0c31f383 c0d0fa00
1f00: c0d2eb80 00000000 c0d2e630 4dad8c49 4da967b0 0000003d 0000003d 00000000
1f20: fffffff5 c0d01f40 c04e0f88 c04e0f8c 30070013 ffffffff
[<c0100b0c>] (__irq_svc) from [<c04e0f8c>] (cpuidle_enter_state+0x7c/0x378)
[<c04e0f8c>] (cpuidle_enter_state) from [<c04e12c4>] (cpuidle_enter+0x28/0x38)
[<c04e12c4>] (cpuidle_enter) from [<c014f710>] (do_idle+0x194/0x214)
[<c014f710>] (do_idle) from [<c014fa50>] (cpu_startup_entry+0xc/0x14)
[<c014fa50>] (cpu_startup_entry) from [<c0a00dc8>] (start_kernel+0x46c/0x4a0)
Code: e580c054 8a000002 e1a00002 e8bd8070 (e7f001f2)
---[ end trace 146c8a334115490c ]---
The solution was to force nonlinear buffers to be cloned. This was previously
reported by Klaus Doth (https://www.spinics.net/lists/netdev/msg556937.html)
but never formally submitted as a patch.
This is the third revision, hopefully the formatting is correct this time!
Suggested-by: Klaus Doth <krnl@doth.eu>
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Signed-off-by: Mark Deneen <mdeneen@saucontech.com>
Link: https://lore.kernel.org/r/20201030155814.622831-1-mdeneen@saucontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for 10GBASE-R interface to the linux driver for
Cadence's ethernet controller.
This controller has separate MAC's and PCS'es for low and high speed paths.
High speed PCS supports 100M, 1G, 2.5G, 5G and 10G through rate adaptation
implementation. However, since it doesn't support auto negotiation, linux
driver is modified to support 10GBASE-R instead of USXGMII.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/1603975627-18338-1-git-send-email-pthombar@cadence.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The at91rm9200 variant used by a few chips including the MSC313 supports
two Tx descriptors (one frame being serialized and another one queued).
However the driver only implemented a single one, which adds a dead time
after each transfer to receive and process the interrupt and wake the
queue up, preventing from reaching line rate.
This patch implements a very basic 2-deep queue to address this limitation.
The tests run on a Breadbee board equipped with an MSC313E show that at
1 GHz, HTTP traffic on medium-sized objects (45kB) was limited to exactly
50 Mbps before this patch, and jumped to 76 Mbps with this patch. And tests
on a single TCP stream with an MTU of 576 jump from 10kpps to 15kpps. With
1500 byte packets it's now possible to reach line rate versus 75 Mbps
before.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-4-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RM9200 supports one frame being sent while another one is waiting in
queue. This avoids the dead time that follows the emission of a frame
and which prevents one from reaching line speed.
Right now the driver supports only a single skb, so we'll first replace
the rm9200-specific skb info with an array of two macb_tx_skb (already
used by other drivers). This patch only moves the skb_length to
txq[0].size and skb_physaddr to skb[0].mapping but doesn't perform any
other change. It already uses [desc] in order to minimize future changes.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-3-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transmit Buffer Register Empty replaces TXERR on RM9200 and signals the
sender may try to send again becase the last queued frame is no longer
in queue (being transmitted or already transmitted).
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-2-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct macb_platform_data is only used by macb_pci to register the platform
device, move its definition to cadence/macb.h and remove platform_data/macb.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of drivers had a "generic documentation" section that
would trigger a "can't understand" message from W=1 compiles.
Fix by using correct DOC: tags in the generic sections.
Fixed Warnings:
drivers/net/ethernet/arc/emac_arc.c:4: info: Scanning doc for c
drivers/net/ethernet/cadence/macb_pci.c:3: warning: missing initial short description on line:
* Cadence GEM PCI wrapper.
drivers/net/ethernet/cadence/macb_pci.c:3: info: Scanning doc for Cadence
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PAE bit of NCFGR register, when set, pauses transmission
if a non-zero 802.3 classic pause frame is received.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I just recently noticed that ethernet does not work anymore since v5.5
on the GARDENA smart Gateway, which is based on the AT91SAM9G25.
Debugging showed that the "GEM bits" in the NCFGR register are now
unconditionally accessed, which is incorrect for the !macb_is_gem()
case.
This patch adds the macb_is_gem() checks back to the code
(in macb_mac_config() & macb_mac_link_up()), so that the GEM register
bits are not accessed in this case any more.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the Wake-on-Lan interrupt for the Cadence MACB Ethernet
controller.
As we do for the GEM version, we handle of WoL interrupt in a
specialized interrupt handler for MACB version that is positionned
just between suspend() and resume() calls.
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the Wake-on-Lan feature to the Cadence GEM Ethernet controller.
This controller has different register layout and cannot be handled by
previous code.
We disable completely interrupts on all the queues but the queue 0.
Handling of WoL interrupt is done in another interrupt handler
positioned depending on the controller version used, just between
suspend() and resume() calls.
It allows to lower pressure on the generic interrupt hot path by
removing the need to handle 2 tests for each IRQ: the first figuring out
the controller revision, the second for actually knowing if the WoL bit
is set.
Queue management in suspend()/resume() functions inspired from RFC patch
by Harini Katakam <harinik@xilinx.com>, thanks!
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to pm_runtime_force_suspend/resume() functions are only
relevant if the device is not configured to act as a WoL wakeup source.
Add the device_may_wakeup() test before calling them.
Fixes: 3e2a5e1539 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we now use the phylink call to phylink_stop() in the non-WoL path,
there is no need for this call to netif_carrier_off() anymore. It can
disturb the underlying phylink FSM.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep previous function goals and integrate phylink actions to them.
phylink_ethtool_get_wol() is not enough to figure out if Ethernet driver
supports Wake-on-Lan.
Initialization of "supported" and "wolopts" members is done in phylink
function, no need to keep them in calling function.
phylink_ethtool_set_wol() return value is considered and determines
if the MAC has to handle WoL or not. The case where the PHY doesn't
implement WoL leads to the MAC configuring it to provide this feature.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the way the "magic-packet" DT property is handled in the
macb_probe() function, matching DT binding documentation.
Now we mark the device as "wakeup capable" instead of calling the
device_init_wakeup() function that would enable the wakeup source.
For Ethernet WoL, enabling the wakeup_source is done by
using ethtool and associated macb_set_wol() function that
already calls device_set_wakeup_enable() for this purpose.
That would reduce power consumption by cutting more clocks if
"magic-packet" property is set but WoL is not configured by ethtool.
Fixes: 3e2a5e1539 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper struct device pointer to check if the wakeup flag
and wakeup source are positioned.
Use the one passed by function call which is equivalent to
&bp->dev->dev.parent.
It's preventing the trigger of a spurious interrupt in case the
Wake-on-Lan feature is used.
Fixes: d54f89af6c ("net: macb: Add pm runtime support")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove is_udp variable that is used in only one place and use
ip_hdr(skb)->protocol == IPPROTO_UDP check instead.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not initialize queue variable. It is already initialized in for loops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hweight32() to count set bits in queue_mask.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 0 of queue_mask is set at the beginning of
macb_probe_queues() function. Do not set it again after reading
DGFG6 but instead use "|=" operator.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA buffers were not freed on failure path of at91ether_open().
Along with changes for freeing the DMA buffers the enable/disable
interrupt instructions were moved to at91ether_start()/at91ether_stop()
functions and the operations on at91ether_stop() were done in
their reverse order (compared with how is done in at91ether_start()):
before this patch the operation order on interface open path
was as follows:
1/ alloc DMA buffers
2/ enable tx, rx
3/ enable interrupts
and the order on interface close path was as follows:
1/ disable tx, rx
2/ disable interrupts
3/ free dma buffers.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call pm_runtime_put_sync() on failure path of at91ether_open.
Fixes: e6a41c23df ("net: macb: ensure interface is not suspended on at91rm9200")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Undo previously done operation in case macb_phylink_connect()
fails. Since macb_reset_hw() is the 1st undo operation the
napi_exit label was renamed to reset_hw.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a disable to NAPI into macb_open, this was
intended to only happen on the error path but accidentally applies
to all paths. This causes NAPI to be disabled on the success path, which
leads to the network to no longer functioning.
Fixes: 014406babc ("net: cadence: macb: disable NAPI on error")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
A call of the function macb_init() can fail in the function
fu540_c000_init. The related system resources were not released
then. use devm_platform_ioremap_resource() to replace ioremap()
to fix it.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Yash Shah <yash.shah@sifive.com>
Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d1cbfd771c ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771c ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit e6a41c23df, while trying to fix an issue,
("net: macb: ensure interface is not suspended on at91rm9200")
introduced a refcounting regression, because in error case refcounter
must be balanced. Fix it by calling pm_runtime_put_noidle() in error case.
While here, fix the same mistake in other couple of places.
Fixes: e6a41c23df ("net: macb: ensure interface is not suspended on at91rm9200")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed-link nodes are treated as PHY nodes by of_mdiobus_child_is_phy().
We must check if the interface is a fixed-link before looking up for PHY
nodes.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the macb ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
at91ether_init was handling the phy mode and speed but since the switch to
phylink, the NCFGR register got overwritten by macb_mac_config(). The issue
is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared
but never restored as they conflict with the PAE, GBE and PCSSEL bits.
Add new capability to differentiate between EMAC and the other versions of
the IP and use it to set and avoid clearing the relevant bits.
Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC
doesn't use any rings/bufffers/queues.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of autosuspend, at91ether_start is called with clocks disabled.
Ensure that pm_runtime doesn't suspend the interface as soon as it is
opened as there is no pm_runtime support is the other relevant parts of the
platform support for at91rm9200.
Fixes: d54f89af6c ("net: macb: Add pm runtime support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f76 ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the issue with fixed link. With fixed-link
device opening fails due to macb_phylink_connect not
handling fixed-link mode, in which case no MAC-PHY connection
is needed and phylink_connect return success (0), however
in current driver attempt is made to search and connect to
PHY even for fixed-link.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify MDIO read/write functions to support
communication with C45 PHY.
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only clk init function in this driver that register a clk is
fu540_c000_clk_init(), and thus we need to unregister the clk when this
driver is removed on that platform. Other init functions, for example
macb_clk_init(), don't register clks and therefore we shouldn't
unregister the clks when this driver is removed. Convert this
registration path to devm so it gets auto-unregistered when this driver
is removed and drop the clk_unregister() calls in driver remove (and
error paths) so that we don't erroneously remove a clk from the system
that isn't registered by this driver.
Otherwise we get strange crashes with a use-after-free when the
devm_clk_get() call in macb_clk_init() calls clk_put() on a clk pointer
that has become invalid because it is freed in clk_unregister().
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Yash Shah <yash.shah@sifive.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case where the PHY isn't described in the device
tree. This is due to the way the MDIO bus is registered in the driver:
whether the PHY is described in the device tree or not, the bus is
registered through of_mdiobus_register. The function masks all the PHYs
and only allow probing the ones described in the device tree. Prior to
the Phylink conversion this was also done but later on in the driver
the MDIO bus was manually scanned to circumvent the fact that the PHY
wasn't described.
This patch fixes it in a proper way, by registering the MDIO bus based
on if the PHY attached to a given interface is described in the device
tree or not.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to kill tasklet in remove.
Add the call to fix it.
Fixes: 032dc41ba6 ("net: macb: Handle HRESP error")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch converts the MACB Ethernet driver to the Phylink framework.
The MAC configuration is moved to the Phylink ops and Phylink helpers
are now used in the ethtools functions. This helps to access the flow
control and pauseparam logic and this will be helpful in the future for
boards using this controller with SFP cages.
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the Tx and Rx buffer initialization into its own
function. This does not modify the behaviour of the driver and will be
helpful to convert the driver to phylink.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.
In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.
For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.
Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_64b_desc is always called when HW_DMA_CAP_64B is defined.
So the return NULL can never be reached. Remove the dead code.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the compatibility string for SiFive FU540-C000 as per the new
string updated in the binding doc.
Reference:
https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Tested-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF is disabled, we get a harmless warning about the
newly added variable:
drivers/net/ethernet/cadence/macb_main.c:48:39: error: 'mgmt' defined but not used [-Werror=unused-variable]
static struct sifive_fu540_macb_mgmt *mgmt;
Move the variable closer to its use inside of the #ifdef.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subns increment register has 24 bits as follows:
RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0]
Fix the same in the driver and increase sub ns resolution to the
best capable, 24 bits. This should be the case on all GEM versions
that this PTP driver supports.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scaled ppm parameter passed to _adjfine() contains a 16 bit
fraction. This just happens to be the same as SUBNSINCR_SIZE now.
Hence define this separately.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The help text makes it look like NET_VENDOR_CADENCE enables support for
Atmel devices, when in reality it's a driver written by Atmel that
supports Cadence devices. This may confuse users that have this device
on a non-Atmel SoC.
The fix is just s/Atmel/Cadence/, but I did go and re-wrap the Kconfig
help text as that change caused it to go over 80 characters.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c218ad5590 ("macb: Add support for SiFive FU540-C000") added a
dependency on the common clock framework to the macb driver, but didn't
express that dependency in Kconfig. As a result macb now fails to
compile on systems without COMMON_CLK, which specifically causes a build
failure on powerpc allyesconfig.
This patch adds the dependency, which results in the macb driver no
longer being selectable on systems without the common clock framework.
All known systems that have this device already support the common clock
framework, so this should not cause trouble for any uses. Supporting
both the FU540-C000 and systems without COMMON_CLK is quite ugly.
I've build tested this on powerpc allyesconfig and RISC-V defconfig
(which selects MACB), but I have not even booted the resulting kernels.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the macb driver to use NAPI GRO helpers when
receiving SKBs. This improves performances.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NAPI_POLL_WEIGHT, the default NAPI poll() weight instead of
redefining our own value (which turns out to be 64 as well).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the MAC address setup in the probe. The MAC address
retrieved using of_get_mac_address was checked for not containing an
error, but it may also be NULL which wasn't tested. Fix it by replacing
IS_ERR with IS_ERR_OR_NULL.
Fixes: 541ddc66d6 ("net: macb: support of_get_mac_address new ERR_PTR error")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The management IP block is tightly coupled with the Cadence MACB IP
block on the FU540, and manages many of the boundary signals from the
MACB IP. This patch only controls the tx_clk input signal to the MACB
IP. Future patches may add support for monitoring or controlling other
IP boundary signals.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 of
the license as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.144869442@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SAMA5D2 SoC has a suspend mode where SoC's power is cut off. Due to this
the registers content is lost after a suspend/resume cycle. The current
suspend/resume implementation covers some of these registers. However
there are few which were not treated (e.g. SCRT2 and USRIO). Apart
from this, netdev features are not restored. Treat these issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Errors are negative numbers. Using %u shows them as very large positive
numbers such as 4294967277 that don't make sense. Use the %d format
instead, and get a much nicer -19.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Fixes: b48e0bab14 ("net: macb: Migrate to devm clock interface")
Fixes: 93b31f48b3 ("net/macb: unify clock management")
Fixes: 421d9df062 ("net/macb: merge at91_ether driver into macb driver")
Fixes: aead88bd0e ("net: ethernet: macb: Add support for rx_clk")
Fixes: f5473d1d44 ("net: macb: Support clock management for tsu_clk")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current order in open:
-> Enable interrupts (macb_init_hw)
-> Enable NAPI
-> Start PHY
Sequence of RX handling:
-> RX interrupt occurs
-> Interrupt is cleared and interrupt bits disabled in handler
-> NAPI is scheduled
-> In NAPI, RX budget is processed and RX interrupts are re-enabled
With the above, on QEMU or fixed link setups (where PHY state doesn't
matter), there's a chance macb RX interrupt occurs before NAPI is
enabled. This will result in NAPI being scheduled before it is enabled.
Fix this macb open by changing the order.
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While moving the chunk of code during 739de9a156
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.
Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add runtime pm functions and move clock handling there.
Add runtime PM calls to mdio functions to allow for active mdio bus.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb should be freed by dev_consume_skb_any() in macb_pad_and_fcs()
when *skb is still used. The *skb is be replaced by nskb, so the
original *skb should be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in at91ether_interrupt() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new compatibility string for this product. It's using
at91sam9260-macb layout but has a newer hardware revision: it's safer
to use its own string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler contains a workaround for RX hang applicable
to Zynq and AT91RM9200 only. Subsequent versions do not need this
workaround. This workaround unnecessarily resets RX whenever RX used
bit read is observed, which can be often under heavy traffic. There
is no other action performed on RX UBR interrupt. Hence introduce a
CAPS mask; enable this interrupt and workaround only on affected
versions.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 653e92a917 ("net: macb: add support for padding and fcs
computation") introduced a bug fixed by commit 899ecaedd1 ("net:
ethernet: cadence: fix socket buffer corruption problem"). Code removed
in this patch is not reachable at all so remove it.
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
