Currently macb sets clock divisor for pclk up to 160 MHz.
Function gem_mdc_clk_div was updated to enable divisor
for higher values of pclk.
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase halt timeout to accommodate for 16K SRAM at 10Mbps rounded.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230316083050.2108-1-harini.katakam@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In zynqmp platforms where firmware supports dynamic SGMII configuration
but has other non-SGMII ethernet devices, it fails them with no packets
received at the RX interface.
To fix this behaviour perform SGMII dynamic configuration only
for the SGMII phy interface.
Fixes: 32cee78181 ("net: macb: Add zynqmp SGMII dynamic configuration support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reported-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1675340779-27499-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver was capturing the TX timestamp values from the TX ring
during the TX completion path, but deferring the actual packet TX
timestamp updating to a workqueue. There does not seem to be much of a
reason for this with the current state of the driver. Simplify this to
just do the TX timestamping as part of the TX completion path, to avoid
the need for the extra timestamp buffer and workqueue.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP TX timestamp handling was observed to be broken with this driver
when using the raw Layer 2 PTP encapsulation. ptp4l was not receiving
the expected TX timestamp after transmitting a packet, causing it to
enter a failure state.
The problem appears to be due to the way that the driver pads packets
which are smaller than the Ethernet minimum of 60 bytes. If headroom
space was available in the SKB, this caused the driver to move the data
back to utilize it. However, this appears to cause other data references
in the SKB to become inconsistent. In particular, this caused the
ptp_one_step_sync function to later (in the TX completion path) falsely
detect the packet as a one-step SYNC packet, even when it was not, which
caused the TX timestamp to not be processed when it should be.
Using the headroom for this purpose seems like an unnecessary complexity
as this is not a hot path in the driver, and in most cases it appears
that there is sufficient tailroom to not require using the headroom
anyway. Remove this usage of headroom to prevent this inconsistency from
occurring and causing other problems.
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> # on SAMA7G5
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `macb_resume`/`macb_suspend` methods already call the
`phylink_start`/`phylink_stop` methods during their execution so
explicitly say that the PM of the PHY is done by MAC by using the
`mac_managed_pm` flag of the `struct phylink_config`.
This also fixes the warning message issued during resume:
WARNING: CPU: 0 PID: 237 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0x144/0x148
Depends-on: 96de900ae7 ("net: phylink: add mac_managed_pm in phylink_config structure")
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221019120929.63098-1-sergiu.moga@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When GEM is in SGMII mode and disabled as a wakeup source, the power
management controller can power down the entire full power domain(FPD)
if none of the FPD devices are in use.
Incase of FPD off, there are below ethernet link up issues on non-wakeup
suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the
resume path which reinitializes PS GTR SGMII lanes.
$ echo +20 > /sys/class/rtc/rtc0/wakealarm
$ echo mem > /sys/power/state
After resume:
$ ifconfig eth0 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
SIOCSIFFLAGS: Connection timed out
phy phy-fd400000.phy.0: phy poweron failed --> -110
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the dynamic configuration which takes care of
configuring the GEM secure space configuration registers
using EEMI APIs.
High level sequence is to:
- Check for the PM dynamic configuration support, if no error proceed with
GEM dynamic configurations(next steps) otherwise skip the dynamic
configuration.
- Configure GEM Fixed configurations.
- Configure GEM_CLK_CTRL (gemX_sgmii_mode).
- Trigger GEM reset.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Conor Dooley <conor.dooley@microchip.com> (for MPFS)
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull AVR32 updates from Hans-Christian Noren Egtvedt:
"Mostly changes to documentation and comments"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
video:backlight: remove reference to AVR32 architecture in ltv350qv
video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
net: remove cdns,at32ap7000-macb device tree entry
misc: update maintainer email address and description for atmel-ssc
mfd: remove reference to AVR32 architecture in atmel-smc.c
dma:dw: remove reference to AVR32 architecture in core.c
The AVR32 architecture has been removed from the kernel in commit
26202873bb, hence clean out the
cdns,at32ap7000-macb compatible entry in Cadence macb Ethernet driver.
AVR32 architecture never supported device tree, hence this code was not
used by anybody.
Updated documentation to match the default entry, no users of
cdns,at32ap7000-macb in the kernel tree.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Use correct vendor for Xilinx versions of Cadence MACB/GEM Ethernet
controller. The Versal compatible was not released, so it can be
changed. Zynq-7xxx and Ultrascale+ has to be kept in new and deprecated
form.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/20220726070802.26579-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On Versal TSU clock cannot be disabled irrespective of whether PTP is
used. Hence introduce a new Versal config structure with a "need tsu"
caps flag and check the same in runtime_suspend/resume before cutting
off clocks.
More information on this for future reference:
This is an IP limitation on versions 1p11 and 1p12 when Qbv is enabled
(See designcfg1, bit 3). However it is better to rely on an SoC specific
check rather than the IP version because tsu clk property itself may not
represent actual HW tsu clock on some chip designs.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort capability flags by the bit position set.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port fields in the ethool flow structures are defined
to be __be16 types, so sparse is showing issues where these
are being passed to htons(). Fix these warnings by passing
them to be16_to_cpu() instead.
These are being used in netdev_dbg() so should only effect
anyone doing debug.
Fixes the following sparse warnings:
drivers/net/ethernet/cadence/macb_main.c:3366:9: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3366:9: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3366:9: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3419:25: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3419:25: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3419:25: warning: cast from restricted __be16
drivers/net/ethernet/cadence/macb_main.c:3419:25: warning: cast from restricted __be16
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Link: https://lore.kernel.org/r/20220715173009.526126-1-ben.dooks@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
init_reset_optional() is somewhat oddly placed amidst the macb_config
struct definitions. Move it to a more reasonable location alongside
the fu540 init functions.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The error handling paths in init_reset_optional() can all be
simplified to return dev_err_probe(). Do so.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The various macb_config structs have taken different approaches to
alignment when broken over newlines. Pick one style and make them
match.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To date, the Microchip PolarFire SoC (MPFS) has been using the
cdns,macb compatible, however the generic device does not have reset
support. Add a new compatible & .data for MPFS to hook into the reset
functionality added for zynqmp support (and make the zynqmp init
function generic in the process).
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JML register on probe will return zero . This register is configured
later on macb_init_hw() which is called on open.
Since we have zero, after header and FCS length subtraction we will get
negative max_mtu size. This issue was affecting DSA drivers with MTU support
(for example KSZ9477).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP one step sync packets cannot have CSUM padding and insertion in
SW since time stamp is inserted on the fly by HW.
In addition, ptp4l version 3.0 and above report an error when skb
timestamps are reported for packets that not processed for TX TS
after transmission.
Add a helper to identify PTP one step sync and fix the above two
errors. Add a common mask for PTP header flag field "twoStepflag".
Also reset ptp OSS bit when one step is not selected.
Fixes: ab91f0a9b5 ("net: macb: Add hardware PTP support")
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220518170756.7752-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.
Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact. A
separate NAPI instance is used for TX and RX to avoid checking the other
ring's state unnecessarily when doing the poll, and so that the NAPI
budget handling can work for both TX and RX packets.
A new per-queue tx_ptr_lock spinlock has been added to avoid using the
main device lock (with IRQs needing to be disabled) across the entire TX
mapping operation, and also to protect the TX queue pointers from
concurrent access between the TX start and TX poll operations.
The TX Used Bit Read interrupt (TXUBR) handling also needs to be moved into
the TX NAPI poll handler to maintain the proper order of operations. A flag
is used to notify the poll handler that a UBR condition needs to be
handled. The macb_tx_restart handler has had some locking added for global
register access, since this could now potentially happen concurrently on
different queues.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously the macb_poll method was checking the RSR register after
completing its RX receive work to see if additional packets had been
received since IRQs were disabled, since this controller does not
maintain the pending IRQ status across IRQ disable. It also had to
double-check the register after re-enabling IRQs to detect if packets
were received after the first check but before IRQs were enabled.
Using the RSR register for this purpose is problematic since it reflects
the global device state rather than the per-queue state, so if packets
are being received on multiple queues it may end up retriggering receive
on a queue where the packets did not actually arrive and not on the one
where they did arrive. This will also cause problems with an upcoming
change to use NAPI for the TX path where use of multiple queues is more
likely.
Add a macb_rx_pending function to check the RX ring to see if more
packets have arrived in the queue, and use that to check if NAPI should
be rescheduled rather than the RSR register. By doing this, we can just
ignore the global RSR register entirely, and thus save some extra device
register accesses at the same time.
This also makes the previous first check for pending packets rather
redundant, since it would be checking the RX ring state which was just
checked in the receive work function. Therefore we can get rid of it and
just check after enabling interrupts whether packets are already
pending.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the macb binding documentation "phys" is an optional property. Make
implementation in line with it. This change allows the traditional flow
in which first stage bootloader does PS-GT configuration to work along
with newer use cases in which PS-GT configuration is managed by the
phy-zynqmp driver.
It fixes below macb probe failure when macb DT node doesn't have SGMII
phys handle.
"macb ff0b0000.ethernet: error -ENODEV: failed to get PS-GTR PHY"
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220411013812.2517212-1-chi.minghao@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 4298388574 ("net: macb: restart tx after tx used bit read")
added support for restarting transmission. Restarting tx does not work
in case controller asserts TXUBR interrupt and TQBP is already at the end
of the tx queue. In that situation, restarting tx will immediately cause
assertion of another TXUBR interrupt. The driver will end up in an infinite
interrupt loop which it cannot break out of.
For cases where TQBP is at the end of the tx queue, instead
only clear TX_USED interrupt. As more data gets pushed to the queue,
transmission will resume.
This issue was observed on a Xilinx Zynq-7000 based board.
During stress test of the network interface,
driver would get stuck on interrupt loop within seconds or minutes
causing CPU to stall.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220407161659.14532-1-tomas.melin@vaisala.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34 ("net: macb: Re-enable RX interrupt only when RX is done")
Cc: stable@vger.kernel.org
Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GEM controllers on ZynqMP were missing some initialization steps which
are required in some cases when using SGMII mode, which uses the PS-GTR
transceivers managed by the phy-zynqmp driver.
The GEM core appears to need a hardware-level reset in order to work
properly in SGMII mode in cases where the GT reference clock was not
present at initial power-on. This can be done using a reset mapped to
the zynqmp-reset driver in the device tree.
Also, when in SGMII mode, the GEM driver needs to ensure the PHY is
initialized and powered on.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.
We must use separate phylink_pcs instances for the USX and SGMII PCS,
rather than just changing the "ops" pointer before re-setting it to
phylink as this interface queries the PCS, rather than requesting it
to be changed.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces bitmap and MAC capabilities mask for
the macb driver and remove the old validate implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mpuRv-00D4rb-Lz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are three boolean variable which were not initialized and later
being used in the code.
Signed-off-by: Yacov Simhony <ysimhony@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several cases where validate() would return bogus supported
modes with unusual combinations of interfaces and capabilities. For
example, if state->interface was 10GBASER and the macb had HIGH_SPEED
and PCS but not GIGABIT MODE, then 10/100 modes would be set anyway. In
another case, SGMII could be enabled even if the mac was not a GEM
(despite this being checked for later on in mac_config()). These
inconsistencies make it difficult to refactor this function cleanly.
There is still the open question of what exactly the requirements for
SGMII and 10GBASER are, and what SGMII actually supports. If someone
from Cadence (or anyone else with access to the GEM/MACB datasheet)
could comment on this, it would be greatly appreciated. In particular,
what is supported by Cadence vs. vendor extension/limitation?
To address this, the current logic is split into three parts. First, we
determine what we support, then we eliminate unsupported interfaces, and
finally we set the appropriate link modes. There is still some cruft
related to NA, but this can be removed in a future patch.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Parshuram Thombare <pthombar@cadence.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211112190400.1937855-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4d98bb0d7e ("net: macb: Use mdio child node for MDIO bus if it
exists") added code to detect if a 'mdio' child node exists to the macb
driver. Ths added code does, however, not actually check if the child node
exists, but if the parent node exists. This results in errors such as
macb 10090000.ethernet eth0: Could not attach PHY (-19)
if there is no 'mdio' child node. Fix the code to actually check for
the child node.
Fixes: 4d98bb0d7e ("net: macb: Use mdio child node for MDIO bus if it exists")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211026173950.353636-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This allows explicitly specifying which children are present on the mdio
bus. Additionally, it allows for non-phy MDIO devices on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update three drivers to use the new phylink_set_10g_modes() helper:
Cadence macb, Freescale DPAA2 and Marvell PP2.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb PTP support currently implements the `gettime64` callback to allow
to retrieve the hardware clock time. Update the implementation to provide
the `gettimex64` callback instead.
The difference between the two is that with `gettime64` a snapshot of the
system clock is taken before and after invoking the callback. Whereas
`gettimex64` expects the callback itself to take the snapshots.
To get the time from the macb Ethernet core multiple register accesses have
to be done. Only one of which will happen at the time reported by the
function. This leads to a non-symmetric delay and adds a slight offset
between the hardware and system clock time when using the `gettime64`
method. This offset can be a few 100 nanoseconds. Switching to the
`gettimex64` method allows for a more precise correlation of the hardware
and system clocks and results in a lower offset between the two.
On a Xilinx ZynqMP system `phc2sys` reports a delay of 1120 ns before and
300 ns after the patch. With the latter being mostly symmetric.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both MAC IPs available on SAMA7G5 support MII on RGMII feature.
Enable these by adding proper capability to proper macb_config
objects.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cadence IP has option to enable MII support on RGMII interface. This
could be selected though bit 28 of network control register. This option
is not enabled on all the IP versions thus add a software capability to
be selected by the proper implementation of this IP.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align for OSSMODE offset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for SRTSM bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff7 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/cadence/macb_pci.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/net/ethernet/cadence/macb_ptp.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable queue is set to bp->queues but these values is not used as it
is overwritten later on, hence redundant assignment can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/cadence/macb_main.c:4919:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/cadence/macb_main.c:4832:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a14d273ba1 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba1 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba1 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restore CMP screener registers on resume path.
Fixes: c1e85c6ce5 ("net: macb: save/restore the remaining registers and features")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, e.g., the ZynqMP, devm_clk_get can return
-EPROBE_DEFER if the clock controller, which is implemented in firmware,
has not been probed yet.
As clk_init is only called during probe, use dev_err_probe to simplify
the error message and hide it for -EPROBE_DEFER.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link configuration in SGMII mode, it's not really
sensible to have auto-negotiation enabled since the link settings are
fixed by definition. In other configurations, such as an SGMII
connection to a PHY, it should generally be enabled.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link configuration with GEM in SGMII mode, such as
for a chip-to-chip interconnect, the link state was always showing as
established regardless of the actual connectivity state. We can monitor
the pcs_link_state bit in the Network Status register to determine
whether the PCS link state is actually up.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no usrio config defined for default gem config leading to
a kernel panic devices that don't define a data. This issue can be
reprdouced with microchip polar fire soc where compatible string
is defined as "cdns,macb".
Fixes: edac63861d ("add userio bits as platform configuration")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MII interface is used, the PHY is the clock master, thus don't
set the clock rate. On Zynq-7000, this will prevent the following
warning:
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210120194303.28268-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new flag MACB_CAPS_CLK_HW_CHG was added and all callers of
macb_set_tx_clk were gated on the presence of this flag.
- if (!clk)
+ if (!bp->tx_clk || !(bp->caps & MACB_CAPS_CLK_HW_CHG))
However the flag was not added to anything other than the new
sama7g5_gem, turning that function call into a no op for all other
systems. This breaks the networking on Zynq.
The commit message adding this states: a new capability so that
macb_set_tx_clock() to not be called for IPs having this
capability
This strongly implies that present of the flag was intended to skip
the function not absence of the flag. Update the if statement to
this effect, which repairs the existing users.
Fixes: daafa1d33c ("net: macb: add capability to not set the clock rate")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210104103802.13091-1-ckeepax@opensource.cirrus.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 0a4e9ce17b.
The code was developed and tested on an MSC313E SoC, which seems to be
half-way between the AT91RM9200 and the AT91SAM9260 in that it supports
both the 2-descriptors mode and a Tx ring.
It turns out that after the code was merged I could notice that the
controller would sometimes lock up, and only when dealing with sustained
bidirectional transfers, in which case it would report a Tx overrun
condition right after having reported being ready, and will stop sending
even after the status is cleared (a down/up cycle fixes it though).
After adding lots of traces I couldn't spot a sequence pattern allowing
to predict that this situation would happen. The chip comes with no
documentation and other bits are often reported with no conclusive
pattern either.
It is possible that my change is wrong just like it is possible that
the controller on the chip is bogus or at least unpredictable based on
existing docs from other chips. I do not have an RM9200 at hand to test
at the moment and a few tests run on a more recent 9G20 indicate that
this code path cannot be used there to test the code on a 3rd platform.
Since the MSC313E works fine in the single-descriptor mode, and that
people using the old RM9200 very likely favor stability over performance,
better revert this patch until we can test it on the original platform
this part of the driver was written for. Note that the reverted patch
was actually tested on MSC313E.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/netdev/20201206092041.GA10646@1wt.eu/
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SAMA7G5 10/100Mbps interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unprepare clocks in case of any failure in fu540_c000_clk_init().
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to disable all macb clocks.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SAMA7G5's ethernet IPs TX clock could be provided by its generic clock or
by the external clock provided by the PHY. The internal IP logic divides
properly this clock depending on the link speed. The patch adds a new
capability so that macb_set_tx_clock() to not be called for IPs having
this capability (the clock rate, in case of generic clock, is set at the
boot time via device tree and the driver only enables it).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary for SAMA7G5 as it uses different values for
PHY interface and also introduces hdfctlen bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In my test setup, I had a SAMA5D27 device configured with ip forwarding, and
second device with usb ethernet (r8152) sending ICMP packets. If the packet
was larger than about 220 bytes, the SAMA5 device would "oops" with the
following trace:
kernel BUG at net/core/skbuff.c:1863!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in: xt_MASQUERADE ppp_async ppp_generic slhc iptable_nat xt_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 can_raw can bridge stp llc ipt_REJECT nf_reject_ipv4 sd_mod cdc_ether usbnet usb_storage r8152 scsi_mod mii o
ption usb_wwan usbserial micrel macb at91_sama5d2_adc phylink gpio_sama5d2_piobu m_can_platform m_can industrialio_triggered_buffer kfifo_buf of_mdio can_dev fixed_phy sdhci_of_at91 sdhci_pltfm libphy sdhci mmc_core ohci_at91 ehci_atmel o
hci_hcd iio_rescale industrialio sch_fq_codel spidev prox2_hal(O)
CPU: 0 PID: 0 Comm: swapper Tainted: G O 5.9.1-prox2+ #1
Hardware name: Atmel SAMA5
PC is at skb_put+0x3c/0x50
LR is at macb_start_xmit+0x134/0xad0 [macb]
pc : [<c05258cc>] lr : [<bf0ea5b8>] psr: 20070113
sp : c0d01a60 ip : c07232c0 fp : c4250000
r10: c0d03cc8 r9 : 00000000 r8 : c0d038c0
r7 : 00000000 r6 : 00000008 r5 : c59b66c0 r4 : 0000002a
r3 : 8f659eff r2 : c59e9eea r1 : 00000001 r0 : c59b66c0
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c53c7d Table: 2640c059 DAC: 00000051
Process swapper (pid: 0, stack limit = 0x75002d81)
<snipped stack>
[<c05258cc>] (skb_put) from [<bf0ea5b8>] (macb_start_xmit+0x134/0xad0 [macb])
[<bf0ea5b8>] (macb_start_xmit [macb]) from [<c053e504>] (dev_hard_start_xmit+0x90/0x11c)
[<c053e504>] (dev_hard_start_xmit) from [<c0571180>] (sch_direct_xmit+0x124/0x260)
[<c0571180>] (sch_direct_xmit) from [<c053eae4>] (__dev_queue_xmit+0x4b0/0x6d0)
[<c053eae4>] (__dev_queue_xmit) from [<c05a5650>] (ip_finish_output2+0x350/0x580)
[<c05a5650>] (ip_finish_output2) from [<c05a7e24>] (ip_output+0xb4/0x13c)
[<c05a7e24>] (ip_output) from [<c05a39d0>] (ip_forward+0x474/0x500)
[<c05a39d0>] (ip_forward) from [<c05a13d8>] (ip_sublist_rcv_finish+0x3c/0x50)
[<c05a13d8>] (ip_sublist_rcv_finish) from [<c05a19b8>] (ip_sublist_rcv+0x11c/0x188)
[<c05a19b8>] (ip_sublist_rcv) from [<c05a2494>] (ip_list_rcv+0xf8/0x124)
[<c05a2494>] (ip_list_rcv) from [<c05403c4>] (__netif_receive_skb_list_core+0x1a0/0x20c)
[<c05403c4>] (__netif_receive_skb_list_core) from [<c05405c4>] (netif_receive_skb_list_internal+0x194/0x230)
[<c05405c4>] (netif_receive_skb_list_internal) from [<c0540684>] (gro_normal_list.part.0+0x14/0x28)
[<c0540684>] (gro_normal_list.part.0) from [<c0541280>] (napi_complete_done+0x16c/0x210)
[<c0541280>] (napi_complete_done) from [<bf14c1c0>] (r8152_poll+0x684/0x708 [r8152])
[<bf14c1c0>] (r8152_poll [r8152]) from [<c0541424>] (net_rx_action+0x100/0x328)
[<c0541424>] (net_rx_action) from [<c01012ec>] (__do_softirq+0xec/0x274)
[<c01012ec>] (__do_softirq) from [<c012d6d4>] (irq_exit+0xcc/0xd0)
[<c012d6d4>] (irq_exit) from [<c0160960>] (__handle_domain_irq+0x58/0xa4)
[<c0160960>] (__handle_domain_irq) from [<c0100b0c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0d01ef0 to 0xc0d01f38)
1ee0: 00000000 0000003d 0c31f383 c0d0fa00
1f00: c0d2eb80 00000000 c0d2e630 4dad8c49 4da967b0 0000003d 0000003d 00000000
1f20: fffffff5 c0d01f40 c04e0f88 c04e0f8c 30070013 ffffffff
[<c0100b0c>] (__irq_svc) from [<c04e0f8c>] (cpuidle_enter_state+0x7c/0x378)
[<c04e0f8c>] (cpuidle_enter_state) from [<c04e12c4>] (cpuidle_enter+0x28/0x38)
[<c04e12c4>] (cpuidle_enter) from [<c014f710>] (do_idle+0x194/0x214)
[<c014f710>] (do_idle) from [<c014fa50>] (cpu_startup_entry+0xc/0x14)
[<c014fa50>] (cpu_startup_entry) from [<c0a00dc8>] (start_kernel+0x46c/0x4a0)
Code: e580c054 8a000002 e1a00002 e8bd8070 (e7f001f2)
---[ end trace 146c8a334115490c ]---
The solution was to force nonlinear buffers to be cloned. This was previously
reported by Klaus Doth (https://www.spinics.net/lists/netdev/msg556937.html)
but never formally submitted as a patch.
This is the third revision, hopefully the formatting is correct this time!
Suggested-by: Klaus Doth <krnl@doth.eu>
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Signed-off-by: Mark Deneen <mdeneen@saucontech.com>
Link: https://lore.kernel.org/r/20201030155814.622831-1-mdeneen@saucontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for 10GBASE-R interface to the linux driver for
Cadence's ethernet controller.
This controller has separate MAC's and PCS'es for low and high speed paths.
High speed PCS supports 100M, 1G, 2.5G, 5G and 10G through rate adaptation
implementation. However, since it doesn't support auto negotiation, linux
driver is modified to support 10GBASE-R instead of USXGMII.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/1603975627-18338-1-git-send-email-pthombar@cadence.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
