Now that there is almost no special case code left in
spi_nor_sr_ready(), the return check looks odd. Move the function call
closer to the return code checking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-32-michael@walle.cc
Drop the generic spi_nor prefix for all the spansion functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-31-michael@walle.cc
Now that all functions using that flag are local to the spansion module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-30-michael@walle.cc
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
Don't return early when the flash is smaller than or equal to 16MiB. We
need to be able to register hooks for all sizes of flashes. This also has
the benefit that it increases the readability of the code because the
action, i.e. registering the fixups, is connected to the condition, i.e.
flashes larger than 16MiB.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-28-michael@walle.cc
Drop the generic spi_nor prefix for all the micron-st functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-27-michael@walle.cc
Now that all functions using that flag are local to the micron module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-26-michael@walle.cc
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
XRDSR is a combination of xilinx and the RDSR opcode, but the register
is just the status register. Correct the debug message.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-24-michael@walle.cc
Drop the generic spi_nor prefix for all the xilinx functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-23-michael@walle.cc
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
The _page_size marco parameter was missing parentheses around it. Add
them.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-21-michael@walle.cc
We will move vendor specific code into the vendor modules and thus we
will have to export these functions so they can be called.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-20-michael@walle.cc
Xilinx and Micron flashes have their own implementation of the
spi_nor_ready() function. At the moment, the core will figure out
which one to call according to some flags. Lay the foundation to
make it possible that a flash can register its own ready()
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-19-michael@walle.cc
Instead of always using a function pointer (and initializing it to our
default), just call the default function if the flash didn't set its own
one. That will make the call flow easier to follow.
Also mark the parameter as optional now.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-18-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-17-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-16-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-15-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-14-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-13-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-12-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-11-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-10-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-9-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-8-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-7-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-6-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-5-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-4-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-3-michael@walle.cc
To avoid name clashes unify all the function and static object names and
use one of the following prefixes which should be sufficiently unique:
- <vendor>_nor_
- <flash_family>_nor_
- <flash_part>_
There are no functional changes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-2-michael@walle.cc
The preferred way to implement SPI-NOR controller drivers is through SPI
subsubsystem utilizing the SPI MEM core functions. This converts the
Intel SPI flash controller driver over the SPI MEM by moving the driver
from SPI-NOR subsystem to SPI subsystem and in one go make it use the
SPI MEM functions. The driver name will be changed from intel-spi to
spi-intel to match the convention used in the SPI subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220209122706.42439-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver tries to disable the BIOS write protection
automatically even if this is not what the user wants. For this reason
modify the driver so that by default it does not touch the write
protection. Only if specifically asked by the user (setting writeable=1
command line parameter) the driver tries to disable the BIOS write
protection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220209122706.42439-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The aspeed-smc can have multiple SPI devices attached to it in the
device tree. If one of the devices is missing or failing the entire
probe will fail and all MTD devices under the controller will be
removed. On OpenBMC this results in a kernel panic due to missing
rootfs:
[ 0.538774] aspeed-smc 1e620000.spi: Using 50 MHz SPI frequency
[ 0.540471] aspeed-smc 1e620000.spi: w25q01jv-iq (131072 Kbytes)
[ 0.540750] aspeed-smc 1e620000.spi: CE0 window [ 0x20000000 - 0x28000000 ] 128MB
[ 0.540943] aspeed-smc 1e620000.spi: CE1 window [ 0x28000000 - 0x2c000000 ] 64MB
[ 0.541143] aspeed-smc 1e620000.spi: read control register: 203b0041
[ 0.581442] 5 fixed-partitions partitions found on MTD device bmc
[ 0.581625] Creating 5 MTD partitions on "bmc":
[ 0.581854] 0x000000000000-0x0000000e0000 : "u-boot"
[ 0.584472] 0x0000000e0000-0x000000100000 : "u-boot-env"
[ 0.586468] 0x000000100000-0x000000a00000 : "kernel"
[ 0.588465] 0x000000a00000-0x000006000000 : "rofs"
[ 0.590552] 0x000006000000-0x000008000000 : "rwfs"
[ 0.592605] aspeed-smc 1e620000.spi: Using 50 MHz SPI frequency
[ 0.592801] aspeed-smc 1e620000.spi: unrecognized JEDEC id bytes: 00 00 00 00 00 00
[ 0.593039] Deleting MTD partitions on "bmc":
[ 0.593175] Deleting u-boot MTD partition
[ 0.637929] Deleting u-boot-env MTD partition
[ 0.829527] Deleting kernel MTD partition
[ 0.856902] Freeing initrd memory: 1032K
[ 0.866428] Deleting rofs MTD partition
[ 0.906264] Deleting rwfs MTD partition
[ 0.986628] aspeed-smc 1e620000.spi: Aspeed SMC probe failed -2
[ 0.986929] aspeed-smc: probe of 1e620000.spi failed with error -2
...
[ 2.936719] /dev/mtdblock: Can't open blockdev
mount: mounting /dev/mtdblock on run/initramfs/ro failed: No such file or directory
[ 2.963030] MTD: Couldn't look up '/dev/mtdblock': -2
mount: mounting /dev/mtdblock on run/initramfs/rw failed: No such file or directory
Mounting read-write /dev/mtdblock filesystem failed. Please fix and run
mount /dev/mtdblock run/initramfs/rw -t jffs2 -o rw
or perform a factory reset with the clean-rwfs-filesystem option.
Fatal error, triggering kernel panic!
[ 3.013047] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
Many BMC designs have two flash chips so that they can handle a hardware
failure of one of them. If one chip failed, it doesn't do any good to
have redundancy if they all get removed anyhow.
Improve the resilience of the probe function to handle one of the
children being missing or failed. Only in the case where all children
fail to probe should the controller be failed out.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211229143334.297305-1-patrick@stwcx.xyz
SPI NOR sysfs defines partname and jedec_id device attributes, which
duplicate the information from debugfs. Since the sysfs directory
structure and the attributes in each directory define an ABI between the
kernel and user space, thus it can never be removed, remove the debugfs
entries so that we don't duplicate the information.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211217122636.474976-2-tudor.ambarus@microchip.com
The Octal DTR configuration is stored in the CFR0V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. The next byte address contains the CFR1V register, which
contains the number of dummy cycles. This is very fortunate since the
enable path changes the value of this register. Reset the value to its
default when disabling Octal DTR mode. This way, both changes to the
flash state made when enabling can be reverted in one single
transaction.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-4-p.yadav@ti.com
The Octal DTR configuration is stored in the CFR5V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. Since the next byte address does not contain any
register, it is safe to write any value to it. Write a 0 to it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-3-p.yadav@ti.com
The template ops used in spi_nor_spimem_check_pp() and
spi_nor_spimem_check_readop() currently set the data phase to 1 byte
long. This is problematic for 8D-8D-8D protocol where odd length data
phase is invalid since one cycle transfers 2 bytes and odd number of
bytes would mean half a cycle is left over. This could result in a
controller rejecting the op as "not supported" even though it actually
supports the protocol.
Change the data length to 2 bytes in these templates. One might argue
that this should only be done for 8D-8D-8D operations but when talking
about these templates, there is no functional difference between one and
two bytes, even in STR modes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210531181757.19458-2-p.yadav@ti.com
Remove the references to the old spi-nor.c file.
The old drivers/mtd/spi-nor/spi-nor.c file
is not more present and now some of its code is contained in:
drivers/mtd/spi-nor/core.c
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
[tudor.ambarus@microchip.com:
- remove change in Documentation/driver-api/mtd/spi-nor.rst.
The documentation has to be rewritten entirely.
- update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20210126092516.1431913-1-f.suligoi@asem.it
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_4B 0x12.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-15-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_1_1_4_4B
0x34.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-14-tudor.ambarus@microchip.com
s25fl256s0 does not define the SFDP tables nor implements the
RDSFDP 0x5a command. Skip the SFDP parsing in order to avoid
issuing an unsupported command to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-13-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4 0xeb,
for erases SPINOR_OP_BE_4K 0x20, and for writes SPINOR_OP_PP 0x02.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-12-tudor.ambarus@microchip.com
spi_nor_setup() configures the SPI NOR memory. Setting the addr width
is too a configuration, hence we can move the spi_nor_set_addr_width()
in spi_nor_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211207140254.87681-11-tudor.ambarus@microchip.com
New flash additions that support SFDP should be declared with
PARSE_SFDP and with all the other flags that are not SFDP
discoverable.
Keep the old way of initializing the flash, until all the flashes
are converted to use either PARSE_SFDP or SPI_NOR_SKIP_SFDP.
Flashes that declare PARSE_SFDP do not have a roll-back mechanism
because if spi_nor_parse_sfdp() returns an error it means that either
BFPT is not supported, thus SFDP is not supported and the user didn't
correctly declared the flash_info entry, or some memalloc failed.
Either way we should return an error. The rest of the SFDP tables are
optional, if one of the optional SFDP tables fails, we just continue.
We would like to get rid of the default_init() hook, so the
spi_nor_manufacturer_init_params() is not called in the new sequnce
of flash initialization.
Split spi_nor_info_init_params() in spi_nor_init_default_params()
and spi_nor_no_sfdp_init_params(). spi_nor_init_default_params() is
called for all the flashes regardless if they support SFDP or not.
spi_nor_no_sfdp_init_params() is called just for the flashes that
do not define SFDP and initializes parameters and setting solely
based on flash_info data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-10-tudor.ambarus@microchip.com
Group NOR flags initialization. Introduce a dedicated function for
setting the fixup_flags and emphasise when those flash_info flags
should be set: when the SNOR_F_4B_OPCODES/SNOR_F_IO_MODE_EN_VOLATILE
setttings can not be discovered by SFDP for this particular flash
because the SFDP table that indicates this support is not defined
in the flash.
In case the table for his support is defined but has wrong values,
one should instead use a post_sfdp() hook to set the SNOR_F equivalent
flag.
No functional change intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-9-tudor.ambarus@microchip.com
Used to initialize the NOR flags for settings that are not defined
in the JESD216 SFDP standard, thus can not be retrieved when parsing
SFDP.
This moves the setting of SNOR_F_READY_XSR_RDY and SNOR_F_HAS_LOCK
late in the init call, without any functional change expected.
The rest of the flags were already set after the spi_nor_init_params().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-8-tudor.ambarus@microchip.com
Clarify for what the flash_info flags are used for. Split them in
four categories and a bool:
1/ FLAGS: flags that indicate support that is not defined by the JESD216
standard in its SFDP tables.
2/ NO_SFDP_FLAGS: these flags are used when the flash does not define the
SFDP tables. These flags indicate support that can be discovered via
SFDP. Used together with SPI_NOR_SKIP_SFDP flag.
3/ FIXUP_FLAGS: flags that indicate support that can be discovered
via SFDP ideally, but can not be discovered for this particular flash
because the SFDP table that indicates this support is not defined by
the flash. In case the table for this support is defined but has wrong
values, one should instead use a post_sfdp() hook to set the SNOR_F
equivalent flag.
4/ MFR_FLAGS: manufacturer private flags. Used in the manufacturer
fixup hooks to differentiate support between flashes of the same
manufacturer.
5/ PARSE_SFDP: sets info->parse_sfdp to true. All flash_info entries
that support SFDP should be converted to set info->parse_sfdp to true.
SPI NOR flashes that statically declare one of the
SPI_NOR_{DUAL, QUAD, OCTAL, OCTAL_DTR}_READ flags and do not support
the RDSFDP command are gratuiously receiving the RDSFDP command
in the attempt of parsing the SFDP tables. It is not desirable to issue
commands that are not supported, so introduce PARSE_SFDP to help on this
situation.
New flash additions/updates should be declared/updated to use either
PARSE_SFDP or SPI_NOR_SKIP_SFDP. Once all the flash_info entries are
converted to use SPI_NOR_SKIP_SFDP or PARSE_SFDP, we can get rid of the
SPI_NOR_SKIP_SFDP flag and use just the bool nor->info->parse_sfdp to
determine whether to parse SFDP or not. SPI_NOR_SKIP_SFDP flag is kept
just as a way to differentiate whether a flash is converted to the new
flags logic or not.
Support that can be discovered when parsing SFDP should not be duplicated
by explicit flags at flash declaration. All the flash parameters will be
discovered when parsing SFDP. Sometimes manufacturers wrongly define some
fields in the SFDP tables. If that's the case, SFDP data can be amended
with the fixups() hooks. It is not common, but if the SFDP tables are
entirely wrong, and it does not worth the hassle to tweak the SFDP
parameters by using the fixups hooks, or if the flash does not define the
SFDP tables at all, then statically init the flash with the
SPI_NOR_SKIP_SFDP flag and specify the rest of flash capabilities with
the flash info flags.
With time, we want to convert all flashes to use PARSE_SFDP and
stop triggering the SFDP parsing with the
SPI_NOR_{DUAL, QUAD, OCTAL*}_READ flags. Getting rid of the
SPI_NOR_{OCTAL, OCTAL_DTR}_READ trigger is easily achievable,
the rest are a long term goal.
Manufacturer specific flags like USE_CLSR, USE_FSR, SPI_NOR_XSR_RDY,
will be removed in a future series.
No functional changes intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-7-tudor.ambarus@microchip.com
Used in the manufacturer fixup hooks to differentiate support
between flashes of the same manufacturer. Not used in the
SPI NOR core.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-6-tudor.ambarus@microchip.com
spi_nor_post_sfdp_fixups() was called even when there were no SFDP
tables defined. late_init() should be instead used for flashes that
do not define SFDP tables.
Use spi_nor_post_sfdp_fixups() just to fix SFDP data. post_sfdp()
hook is as of now used just by s28hs512t, mt35xu512aba, and both
support SFDP, there's no functional change with this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-5-tudor.ambarus@microchip.com
Used to init all the mtd_info fields. Move the mtd_info init
the last thing in the spi_nor_scan(), so that we avoid superfluous
initialization of the mtd_info fields in case of errors.
While here use common naming scheme for functions that are setting
mtd_info fields:
s/spi_nor_register_locking_ops/spi_nor_set_mtd_locking_ops
s/spi_nor_otp_init/spi_nor_set_mtd_otp_ops
The functions names are self explanatory, get rid of the comment
for the OTP function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-4-tudor.ambarus@microchip.com
Use NOR parameters in the probe's sequence of calls, thus
nor->params->size instead of nor->mtd.size and let the mtd_info
fields be used by the mtd calls (mtd->_erase, mtd->_read, mtd->_write).
mtd_info fields should not be used during probe because we haven't
registered mtd yet. It's safe to drop xilinx's setting of nor->mtd.size,
now that we use nor->params->size in spi_nor_set_addr_width().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-3-tudor.ambarus@microchip.com
As it was before the blamed commit, s3an_nor_scan() was called
after mtd size was set with params->size, and it overwrote the mtd
size value with '8 * nor->page_size * nor->info->n_sectors' when
XSR_PAGESIZE was set. With the introduction of
s3an_post_sfdp_fixups(), we missed to update the mtd size for the
s3an flashes. Fix the mtd size by updating both nor->params->size,
(which will update the mtd_info size later on) and nor->mtd.size
(which is used in spi_nor_set_addr_width()).
Fixes: 641edddb4f ("mtd: spi-nor: Add s3an_post_sfdp_fixups()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-2-tudor.ambarus@microchip.com
spansion_post_sfdp_fixups() was called regardless if the flash defined
SFDP tables or not. A better place for this kind of parameters init is
in manufacturer's late_init() hook. post_sfdp() should be called only
when SFDP is defined. No functional change in this patch.
Instead of doing the 4b opcodes settings at manufacturer level, thus
also for every flash that will be introduced, this should be done
just where it is needed, per flash. I'll let this for other patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-12-tudor.ambarus@microchip.com
Setting the correct nor->mtd._write in a fixup hook was misleading,
since this is not a fixup, just a specific setting for SST, that differs
from the SPI NOR core default init.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-11-tudor.ambarus@microchip.com
post_sfdp was misleading in this case, as SFDP is not supported by
xilinx. Plus, there's no fixup here, just setting the correct
setup method, as required by xilinx parts.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-10-tudor.ambarus@microchip.com
OTP is not described in the JESD216 SFDP standard, place the
OTP ops init in late_init().
We can't get rid of the default_init() hook for winbond, as the
4byte_addr_mode is SFDP specific and will require to have all
flashes at hand, in order to check which has the SFDP tables defined,
in which case there's nothing to do if the SFDP tables are corect,
and which of the flashes do not define the SFDP tables in which case
each flash should declare a late_init() fixup.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-9-tudor.ambarus@microchip.com
Locking is not described in JESD216 SFDP standard, place the
locking init in late_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-8-tudor.ambarus@microchip.com
Locking is not described in JESD216 SFDP standard, place the
locking init in late_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-7-tudor.ambarus@microchip.com
Flash parameters init is done in a spaghetti way right now.
There is the init based on the flash_info data, then there is the
default_init() hook, then SFDP init, an intermediary post_bft(),
then post_sfdp() and a spi_nor_late_init_params(). Each method can
overwrite previuosly initialized parameters.
We want to separate what is SFDP and non-SFDP specific. late_init()
will replace the default_init() hook and will be used only to initialize
flash parameters that are not declared in the JESD216 SFDP standard, or
where SFDP tables are not defined at all.
We cut a member in the chain of initializing parameters by getting rid
of the default_init() hook, and we make it clear that everything that is
in late_init() is not covered by the SFDP tables defined by the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-6-tudor.ambarus@microchip.com
nor->page_size duplicated what nor->params->page_size indicates
for no good reason. page_size is a flash parameter of fixed value
and it is better suited to be found in nor->params->page_size.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211029172633.886453-5-tudor.ambarus@microchip.com
"struct mtd_info mtd" is member of "struct spi_nor", there's no need
to use "mtd->priv". Get the pointer to the containing struct spi_nor
by using container_of. While here, make the function inline and
get rid of the __maybe_unused.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-3-tudor.ambarus@microchip.com
Update the description of the otp member of the
struct spi_nor_flash_parameter.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211029172633.886453-2-tudor.ambarus@microchip.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074307.9733-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074259.9683-1-caihuoqing@baidu.com
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
As 4bit block protection patchset for some micron models are merged,
n25q128a13 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a13, the locking functions work well.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210628211729.3625017-1-jonathan.lemon@gmail.com
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Add support to show the manufacturer, the partname and JEDEC identifier
as well as to dump the SFDP table. Not all flashes list their SFDP table
contents in their datasheet. So having that is useful. It might also be
helpful in bug reports from users.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Winbond flashes with OTP support provide a command to erase the OTP
data. This might come in handy during development.
This was tested with a Winbond W25Q32JW on a LS1028A SoC with the
NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
SPI NOR flashes will just ignore program commands if the OTP region is
locked. Thus, a user might not notice that the intended write didn't end
up in the flash. Return -EROFS to the user in this case. From what I can
tell, chips/cfi_cmdset_0001.c also return this error code.
One could optimize spi_nor_mtd_otp_range_is_locked() to read the status
register only once and not for every OTP region, but for that we would
need some more invasive changes. Given that this is
one-time-programmable memory and the normal access mode is reading, we
just live with the small overhead.
By moving the code around a bit, we can just check the length before
calling spi_nor_mtd_otp_range_is_locked() and avoid an underflow there
if a len is 0. This way we don't need to take the lock either. We also
skip the "*retlen = 0" assignment, mtdcore already takes care of that
for us.
Fixes: 069089acf8 ("mtd: spi-nor: add OTP support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Use the wording as used in the datasheet to describe the access methods
of the security registers (aka OTP storage). This will also match the
function names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The security registers either take a 3 byte or a 4 byte address offset,
depending on the address mode of the flash. Thus just leave the
nor->addr_width as is.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Macronix MX25L12805D supports locking with 4 block
protection bits in its status register. Add the corresponding
flag in order to clear these bits when unloking the flash.
Otherwise, the flash might not be writable depending on the state
left by the bootloader.
Tested-on: Ubiquiti UniFi AC Lite (ath79)
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
According to macronix website, there is no mx66l51235l part number.
The chip detected as such is actually mx66l51235f. Rename the flash.
Do not update the mx66l51235l name from the spi_nor_dev_ids[], since
there are dt that are using this compatible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Intel Alder Lake-M has the same SPI serial flash controller as Alder
Lake-S. Add Alder Lake-M PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use the correct argument names in the kerneldoc.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Reported-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Document what the function does and that it should only be used when it
is known that the device supports it. This will avoid unaware
programmers thinking that they can arbitrarily use it to reset the
device.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use SPI_MODE_X_MASK instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
This reverts commit 04b8edad26.
mx25l51245g and mx66l51235l have the same flash ID. The flash
detection returns the first entry in the flash_info array that
matches the flash ID that was read, thus for the 0xc2201a ID,
mx25l51245g was always hit, introducing a regression for
mx66l51235l.
If one wants to differentiate the flash names, a better fix would be
to differentiate between the two at run-time, depending on SFDP,
and choose the correct name from a list of flash names, depending on
the SFDP differentiator.
Fixes: 04b8edad26 ("mtd: spi-nor: macronix: Add support for mx25l51245g")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210402082031.19055-2-tudor.ambarus@microchip.com
If rmmod the driver during read or write, the driver will release the
resources which are used during read or write, so it is possible to
refer to NULL pointer.
Use the testcase "mtd_debug read /dev/mtd0 0xc00000 0x400000 dest_file &
sleep 0.5;rmmod spi_hisi_sfc_v3xx.ko", the issue can be reproduced in
hisi_sfc_v3xx driver.
To avoid the issue, fill the interface _get_device and _put_device of
mtd_info to grab the reference to the spi controller driver module, so
the request of rmmod the driver is rejected before read/write is finished.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1617262486-4223-1-git-send-email-yangyicong@hisilicon.com
With all the helper functions in place, add OTP support for the Winbond
W25Q32JW and W25Q32FW.
Both were tested on a LS1028A SoC with a NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-4-michael@walle.cc
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
SPI flashes sometimes have a special OTP area, which can (and is) used to
store immutable properties like board serial number or vendor assigned
network hardware addresses.
The MTD subsystem already supports accessing such areas and some (non
SPI NOR) flashes already implement support for it. It differentiates
between user and factory areas. User areas can be written by the user and
factory ones are pre-programmed and locked down by the vendor, usually
containing an "electrical serial number". This patch will only add support
for the user areas.
Lay the foundation and implement the MTD callbacks for the SPI NOR and add
necessary parameters to the flash_info structure. If a flash supports OTP
it can be added by the convenience macro OTP_INFO(). Sometimes there are
individual regions, which might have individual offsets. Therefore, it is
possible to specify the starting address of the first regions as well as
the distance between two regions (e.g. Winbond devices uses this method).
Additionally, the regions might be locked down. Once locked, no further
write access is possible.
For SPI NOR flashes the OTP area is accessed like the normal memory, e.g.
by offset addressing; except that you either have to use special read/write
commands (Winbond) or you have to enter (and exit) a specific OTP mode
(Macronix, Micron).
Thus we introduce four operations to which the MTD callbacks will be
mapped: .read(), .write(), .lock() and .is_locked(). The read and the write
ops will be given an address offset to operate on while the locking ops use
regions because locking always affects a whole region. It is up to the
flash driver to implement these ops.
Signed-off-by: Michael Walle <michael@walle.cc>
[ta: use div64_u64(), IS_ALIGNED, params->otp.org. unsigned int region,
drop comment, add rlen local variable in spi_nor_mtd_otp_lock()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-2-michael@walle.cc
It makes the core file a bit smaller and provides better separation
between the Software Write Protection features and the core logic.
All the next generic software write protection features (e.g. Individual
Block Protection) will reside in swp.c.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210322075131.45093-2-tudor.ambarus@microchip.com
s/legacy/default. spi_nor_info_init_params initializes some default
flash parameters and settings that can be overwritten when parsing
SFDP, or by fixup hooks. There's nothing legacy about them, they are
just some default settings, if not otherwise discovered or specified.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210315055634.17332-1-tudor.ambarus@microchip.com
spi_nor_parse_sfdp(nor, nor->params);
passes for the second argument a member within the first argument.
Drop the second argument and obtain it directly from the first,
and do it across all the children functions. This is a follow up for
'commit 69a8eed58c ("mtd: spi-nor: Don't copy self-pointing struct around")'
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210306095002.22983-4-tudor.ambarus@microchip.com
addr and len were gratuitously updated even when spi_nor_wait_till_ready()
failed. Wait for the erase cmd to complete and then advance the erase.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210306095002.22983-2-tudor.ambarus@microchip.com
In order to group x86 related platform data move intel-spi.h to x86 folder.
While at it, remove duplicate inclusion in C file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ta: s/x85/x86]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210304140820.56692-1-andriy.shevchenko@linux.intel.com
Add support for w25q512jvq. This is of the same series chip with
w25q256jv, which is already supported, but with size doubled and
different JEDEC ID.
Tested on Intel whitley platform with dd from/to the flash for
read/write respectly, and flash_erase for erasing the flash.
Signed-off-by: Shuhao Mai <shuhao.mai.1990@gmail.com>
[ta: put flash_info flags in order, first SPI_NOR_DUAL_READ, then
SPI_NOR_QUAD_READ]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210208075303.4200-1-shuhao.mai.1990@gmail.com
Even if sst26vf shares the SPINOR_OP_GBULK opcode with
Macronix (ex. MX25U12835F) and Winbound (ex. W25Q128FV),
it has its own Individual Block Protection scheme, which
is also capable to read-lock individual parameter blocks.
Thus the sst26vf's Individual Block Protection scheme will
reside in the sst.c manufacturer driver.
Add support to unlock the entire flash memory. The device
is write-protected by default after a power-on reset cycle
(volatile software protection), in order to avoid inadvertent
writes during power-up. Could do an erase, write, read back,
and compare when MTD_SPI_NOR_SWP_DISABLE_ON_VOLATILE=y.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210121110546.382633-2-tudor.ambarus@microchip.com
The Global Block Unlock command has different names depending
on the manufacturer, but always the same command value: 0x98.
Macronix's MX25U12835F names it Gang Block Unlock, Winbond's
W25Q128FV names it Global Block Unlock and Microchip's
SST26VF064B names it Global Block Protection Unlock.
Used in the Individual Block Protection mode, which is mutually
exclusive with the Block Protection mode (BP0-3).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210121110546.382633-1-tudor.ambarus@microchip.com
Even if erase type is same as previous region, erase size can be different
if the previous region is overlaid region. Since 'region->size' is assigned
to 'cmd->size' for overlaid region, comparing 'erase->size' and 'cmd->size'
can detect previous overlaid region.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/13d47e8d8991b8a7fd8cc7b9e2a5319c56df35cc.1601612872.git.Takahiro.Kuwano@infineon.com
In case of overlaid regions in which their biggest erase size command
overpasses in size the region's size, only the non-overlaid portion of
the sector gets erased. For example, if a Sector Erase command is applied
to a 256-kB range that is overlaid by 4-kB sectors, the overlaid 4-kB
sectors are not affected by the erase.
For overlaid regions, 'region->size' is assigned to 'cmd->size' later in
spi_nor_init_erase_cmd(), so 'erase->size' can be greater than 'len'.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Update commit description, add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/fa5d8b944a5cca488ac54ba37c95e775ac2deb34.1601612872.git.Takahiro.Kuwano@infineon.com
At the time spi_nor_region_check_overlay() is called, the erase types are
sorted in ascending order of erase size. The 'erase_type' should be masked
with 'BIT(erase[i].idx)' instead of 'BIT(i)'.
Fixes: b038e8e3be ("mtd: spi-nor: parse SFDP Sector Map Parameter Table")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/fd90c40d5b626a1319a78fc2bcee79a8871d4d57.1601612872.git.Takahiro.Kuwano@infineon.com
Intel Alder Lake-P has the same SPI serial flash controller as Alder
Lake-S. Add Alder Lake-P PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210113101545.71579-1-mika.westerberg@linux.intel.com
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl/XAWAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW40rIB/sG1foD0j1iImcTfjlVW4I21HabniykUPBw
GTUlsHoDEEjhY3jEjdYx+l8HHdcqadmedR27DO91l+2ieR7uVoIn2lTADbxnWrgl
DsE6aQLf7KWn340UxEUtihNaa14Zr45GcpYdqs0tjMClRHxM0udwd6qIFHGCi9AC
MOA6kFJewLdCqIRYwBoo1VD4iYQA0RMR463KLvIdrS1bGpkaB3ihxBZb3QgR2ILD
mG9sZClCzeivjNkuiCrJrkWZgAvYTM5DZugBd9+X85Qtq4921zQS5QfZLA9UjnFh
7ChrsTJQFz6CByt6oAH4jCtc0T1hJRL9o1FlbIsAO6gP5mRxKFUV
=bIwk
-----END PGP SIGNATURE-----
mergetag object ee4e0eafa4
type commit
tag nand/for-5.11
tagger Miquel Raynal <miquel.raynal@bootlin.com> 1608042580 +0100
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl/Yz80ACgkQJWrqGEe9
VoTGxAf8CqJ1nc3kuhHasjyIQ+cCK6TkqP3KciGXOlmLJXFkhvk9ge/9Q0qttevh
gA/y5wQWn4L7o5nssslKNZ9UXCv7Ksopukx8gFjXHXM0CeukJ7Px3Phlu27WLiOn
qgmSX3xTVV8wdcVXxS+iNpsu3v5G/H4rZLb2V0bH8+tvalAEje8k6AHP4XLLrjIS
mcjkhLn46ttT7WvxmVmlUN+ghrmFRT5DnhgaD7JdE9beaJv8yZ8MLoz5oFD56Z9S
f7qYugVW0ClOK/YvuPRRCiJcMg3siHxm8XtqQTA2spq/LY6hBEykNFlxbQ/23DXa
1kCUi2L1ld+JOe9YgK+OskoIf+Fywg==
=mqSb
-----END PGP SIGNATURE-----
Merge tags 'spi-nor/for-5.11' and 'nand/for-5.11' into mtd/next
SPI NOR core changes:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
Traditionally, Linux unlocks the whole flash because there are legacy
devices which has the write protection bits set by default at startup.
If you actually want to use the flash protection bits, eg. because there
is a read-only part for a bootloader, this automatic unlocking is
harmful. If there is no hardware write protection in place (usually
called WP#), a startup of the kernel just discards this protection.
I've gone through the datasheets of all the flashes (except the Intel
ones where I could not find any datasheet nor reference) which supports
the unlocking feature and looked how the sector protection was
implemented. The currently supported flashes can be divided into the
following two categories:
(1) block protection bits are non-volatile. Thus they keep their values
at reset and power-cycle
(2) flashes where these bits are volatile. After reset or power-cycle,
the whole memory array is protected.
(a) some devices needs a special "Global Unprotect" command, eg.
the Atmel AT25DF041A.
(b) some devices require to clear the BPn bits in the status
register.
Due to the reasons above, we do not want to clear the bits for flashes
which belong to category (1). Fortunately for us, only Atmel flashes
fall into category (2a). Implement the "Global Protect" and "Global
Unprotect" commands for these. For (2b) we can use normal block
protection locking scheme.
This patch adds a new flag to indicate the case (2). Only if we have
such a flash we unlock the whole flash array. To be backwards compatible
it also introduces a kernel configuration option which restores the
complete legacy behavior ("Disable write protection on any flashes").
Hopefully, this will clean up "unlock the entire flash for legacy
devices" once and for all.
For reference here are the actually commits which introduced the legacy
behavior (and extended the behavior to other chip manufacturers):
commit f80e521c91 ("mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips")
commit ea60658a08 ("mtd: m25p80: disable SST software protection bits by default")
commit 7228982442 ("[MTD] m25p80: fix bug - ATmel spi flash fails to be copied to")
Actually, this might also fix handling of the Atmel AT25DF flashes,
because the original commit 7228982442 ("[MTD] m25p80: fix bug -
ATmel spi flash fails to be copied to") was writing a 0 to the status
register, which is a "Global Unprotect". This might not be the case in
the current code which only handles the block protection bits BP2, BP1
and BP0. Thus, it depends on the current contents of the status register
if this unlock actually corresponds to a "Global Unprotect" command. In
the worst case, the current code might leave the AT25DF flashes in a
write protected state.
The commit 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE
is set on spansion flashes") changed that behavior by just clearing BP2
to BP0 instead of writing a 0 to the status register.
Further, the commit 3e0930f109 ("mtd: spi-nor: Rework the disabling
of block write protection") expanded the unlock_all() feature to ANY
flash which supports locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-8-michael@walle.cc
These flashes have some weird BP bits mapping which aren't supported in
the current locking code. Just add a simple unlock op to unprotect the
entire flash array which is needed for legacy behavior.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-7-michael@walle.cc
For the Atmel and SST parts this flag was already moved to individual
flash parts because it is considered bad esp. because newer flash chips
will automatically inherit the "has locking" support. While this won't
likely be the case for the Intel parts, we do it for consistency
reasons.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-6-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all SST parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes
which supports BP locking. In particular the following flashes
don't support the BP scheme:
- SST26VF016B
- SST26WF016B
- SST26VF064B
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-5-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all Atmel parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes which
supports BP locking. In particular the following flashes don't support
the BP scheme:
- AT26F004
- AT25SL321
- AT45DB081D
Please note, that some flashes which are marked as SPI_NOR_HAS_LOCK just
support Global Protection, i.e. not our supported block protection
locking scheme. This is to keep backwards compatibility with the
current "unlock all at boot" mechanism. In particular the following
flashes doesn't have BP bits:
- AT25DF041A
- AT25DF321
- AT25DF321A
- AT25DF641
- AT26DF081A
- AT26DF161A
- AT26DF321
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-4-michael@walle.cc
Just try to unlock the whole SPI-NOR flash array. Don't abort the
probing in case of an error. Justifications:
(1) For some boards, this just works because
spi_nor_write_16bit_sr_and_check() is broken and just checks the
second half of the 16bit. Once that will be fixed, SPI probe will
fail for boards which has hardware-write protected SPI-NOR flashes.
(2) Until now, hardware write-protection was the only viable solution
to use the block protection bits. This is because this very
function spi_nor_unlock_all() will be called unconditionally on
every linux boot. Therefore, this bits only makes sense in
combination with the hardware write-protection. If we would fail
the SPI probe on an error in spi_nor_unlock_all() we'd break
virtually all users of the block protection bits.
(3) We should try hard to keep the MTD working even if the flash might
not be writable/erasable.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-3-michael@walle.cc
This flash part actually has 4 block protection bits.
Please note, that this patch is just based on information of the
datasheet of the datasheet and wasn't tested.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-2-michael@walle.cc
The S28 flash family uses 2-bit ECC by default with each ECC block being
16 bytes. Under this scheme multi-pass programming to an ECC block is
not allowed. Set the writesize to make sure multi-pass programming is
not attempted on the flash.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-4-p.yadav@ti.com
Some flashes like the Cypress S28 family use ECC. Under this ECC scheme,
multi-pass writes to an ECC block is not allowed. In other words, once
data is programmed to an ECC block, it can't be programmed again without
erasing it first.
Upper layers like file systems need to be given this information so they
do not cause error conditions on the flash by attempting multi-pass
programming. This can be done by setting 'writesize' in 'struct
mtd_info'.
Set the default to 1 but allow flashes to modify it in fixup hooks. If
more flashes show up with this constraint in the future it might be
worth it to add it to 'struct flash_info', but for now increasing its
size is not worth it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-3-p.yadav@ti.com
There are a few typos in comments in the SPI NOR framework; fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201130152416.1283972-1-j.neuschaefer@gmx.net
Fixes the following W=1 kernel build warning(s):
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'np' not described in 'hisi_spi_nor_register'
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'host' not described in 'hisi_spi_nor_register'
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-8-lee.jones@linaro.org
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
The flash supports the soft reset sequence. So, add the flag in the
flash's info.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-16-p.yadav@ti.com
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com
On resume, the init procedure will be run that will re-enable it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-14-p.yadav@ti.com
Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-13-p.yadav@ti.com
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-12-p.yadav@ti.com
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-11-p.yadav@ti.com
Parse just the 22nd dword and look for the 'DTR Octal Mode Enable
Volatile bit'.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes
that don't define the optional SFDP SCCR Map. For the others,
let the SFDP do its job and fill the SNOR_F_IO_MODE_EN_VOLATILE
flag. We avoid this way polluting the flash flags when declaring
one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-10-p.yadav@ti.com
We don't want to enter a stateful mode, where a X-X-X I/O mode
is entered by setting a non-volatile bit, because in case of a
reset or a crash, once in the non-volatile mode, we may not be able
to recover in bootloaders and we may break the SPI NOR boot.
Forbid by default the I/O modes that are set via a non-volatile bit.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes that
don't define the optional SFDP SCCR Map, so that we don't pollute the
flash info flags.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-9-p.yadav@ti.com
Some controllers, like the cadence qspi controller, have trouble reading
only 1 byte in DTR mode. So, do 2 byte reads for SR and FSR commands in
DTR mode, and then discard the second byte.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-8-p.yadav@ti.com
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-7-p.yadav@ti.com
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
dummy cycles, the number of dummy cycles needed for a Read Status
Register command, and the number of address bytes needed for a Read
Status Register command.
We don't know what speed the controller is running at. Find the fast
read dummy cycles for the fastest frequency the flash can run at to be
sure we are never short of dummy cycles. If nothing is available,
default to 20. Flashes that use a different value should update it in
their fixup hooks.
Since we want to set read settings, expose spi_nor_set_read_settings()
in core.h.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-6-p.yadav@ti.com
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-5-p.yadav@ti.com
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-4-p.yadav@ti.com
They are thin wrappers around
nor->controller_ops->{read_reg,write_reg,erase}(). In a future commit
DTR support will be added. These ops can not be supported by the
controller_ops hooks and these helpers will make it easier to reject
those calls.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-3-p.yadav@ti.com
ENOTSUPP is not a SUSV4 error code. Using EOPNOTSUPP is preferred
in its stead.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-2-p.yadav@ti.com
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_set_addr_width() doesn't catch it because addr_width
did get set. This fixes that check.
Fixes: f9acd7fa80 ("mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths")
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20201006132346.12652-1-bert@biot.com
This reverts commit 03edda0e1e.
This leads to warn dump like [1] on some platforms and reorders MTD
devices which may break user space expectations [2]. So revert the change.
[1]:
[ 1.849801] ------------[ cut here ]------------
[ 1.854271] mscc_felix 0000:00:00.5: device is disabled, skipping
[ 1.858753] WARNING: CPU: 1 PID: 7 at kernel/kmod.c:136 __request_module+0x3a4/0x568
[...]
[2] Bug report: https://lore.kernel.org/linux-mtd/20201003150633.23416-1-michael@walle.cc/
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201005090321.8724-1-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-3-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-2-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Fixes: bce679e5ae ("mtd: spi-nor: Check for errors after each Register Operation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/282e1305-fd08-e446-1a22-eb4dff78cfb4@nokia.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
Intel Tiger Lake-H has the same SPI serial flash controller as Cannon
Lake. Add Tiger Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200624192103.78770-1-mika.westerberg@linux.intel.com
Intel Emmitsburg has the same SPI serial flash controller as Lewisburg.
Add Emmitsburg PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200615155748.920-1-mika.westerberg@linux.intel.com
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move cadence-quadspi driver to use spi-mem framework. This is required
to make the driver support for SPI NAND flashes in future.
Driver is feature compliant with existing SPI NOR version.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-8-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care
of sending WREN command before sending erase command.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-7-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider
is not yet probed. Currently driver just falls back to using PIO mode
(which is less efficient) in this case. Instead return probe deferral
error as is so that driver will be re probed once DMA provider is
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-6-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to undo the prior changes done by the driver when exiting due
to failure to acquire reset lines.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-5-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver fails to acquire DMA channel then don't initialize
rx_dma_complete struct as it won't be used.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-4-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently direct access mode is used on platforms that have AHB window
(memory mapped window) larger than flash size. This feature is limited
to TI platforms as non TI platforms have < 1MB of AHB window.
Therefore introduce a driver quirk to disable DAC mode and set it for
non TI compatibles. This is in preparation to move to spi-mem framework
where flash geometry cannot be known.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop configuration of Flash size, erase size and page size
configuration. Flash size is needed only if using AHB decoder (BIT 23 of
CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN
automatically. But since SPI NOR layer takes care of sending WREN, there
is no need to configure these fields either.
Therefore drop these in preparation to move the driver to spi-mem
framework where flash geometry is not visible to controller driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.
Fixes: 10050a02f7 ("mtd: spi-nor: Add 4B_OPCODES flag to w25q256")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Despite of how spi_nor_parse_bfpt() abuses the structure fields during
their calculation, gcc manages to make some decent code out of that. :-)
Yet adding a local variable to store the BFPT DWORDs during calculations
still saves 12 bytes of the object code (AArch64 gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
JESD216D.01 says that when the address width can be 3 or 4, it defaults
to 3 and enters 4-byte mode when given the appropriate command. So, when
we see a configurable width, default to 3 and let flash that default to
4 change it in a post-bfpt fixup.
This fixes SMPT parsing for flashes with configurable address width. If
the SMPT descriptor advertises variable address width, we use
nor->addr_width as the address width. But since it was not set to any
value from the SFDP table, the read command uses an address width of 0,
resulting in an incorrect read being issued.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Cypress cy15b104q and cy15v104q are 4Mbit serial SPI F-RAM devices.
Add support for them to the spi-nor driver.
The actual Device ID of this chip is 7f 7f 7f 7f 7f 7f c2 2c 04. That is
six times the continuation code 7f followed by c2 for Ramtron.
Unfortunately the chip sends the Device ID in reversed order, so the
continuation code is not at the beginning, but instead at the end. Even
more unfortunate is that when reading further the chip sends more 7f
codes which means we are not even able to count the continuation codes.
We can only hope that this reversed Device ID will never match any other
devices ID.
Collisions are improbable as of now, the solution from above is good
enough. In case of future collisions one can introduce an INFO9 macro,
with the downsize that struct flash_info would grow and we have lots of
flashes. A more elegant solution would be to introduce dedicated
flash ID tables for each bank in JESP106BA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[tudor.ambarus@microchip.com: amend commit description with possible
future solutions in case collisions occur.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The correct terminology is serial NOR flash or SPI NOR.
s/SPI-NOR/SPI NOR and s/spi-nor/SPI NOR across the subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.
Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.
The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes. Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:
https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/
Fixes: dfd2b74530 ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The functions return 1 if ready, 0 if not ready, -errno on errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_ready() returns 1 if ready, 0 if not ready and -errno on errors.
Do the same in all the spi_nor_*_ready() children.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
n25q00 uses the 4 bit Block Protection scheme and supports Top/Bottom
protection via the BP and TB bits of the Status Register.
Enable locking for n25q00. Tested with cirrus controller.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mx25u51245g is a mass production for new design and
replace mx66u51235f(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mx25l51245g is a mass production for new design and
replace mx66l51235l(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_info_init_params(), spi_nor_sfdp_init_params(), and
spi_nor_init_params() were added, the kernel-doc for them contained
a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix them.
Fixes: 1c1d8d98e1 ("mtd: spi-nor: Split spi_nor_init_params()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_manufacturer_init_params() was added, the kernel-doc for it
contained a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix it.
Fixes: ce0b6f3f3c ("mtd: spi-nor: Add default_init() hook to tweak flash parameters")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
As 4bit block protection patchset for some micron models are merged,
n25q128a11 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a11, the locking functions work well.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Tested-by: Shreyas Joshi <shreyasjoshi15@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry. Tested with the device and
confirmed that is working.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Commit a0900d0195 ("mtd: spi-nor: Prepare core / manufacturer code
split") moved various files into a new directory, but did not add the new
directory to its parent directory Makefile. The moved files no longer
build, and affected flash chips no longer instantiate.
Adding the new directory to the parent directory Makefile fixes the
problem.
Fixes: a0900d0195 ("mtd: spi-nor: Prepare core / manufacturer code split")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Use Joe Perches cvt_fallthrough.pl script to convert
/* fallthrough */
comments (and its derivatives) into a
fallthrough;
statement. This automatically drops useless ones.
Do it MTD-wide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200325212115.14170-1-miquel.raynal@bootlin.com
n25q512ax3 and n25q512a use the 4 bit Block Protection scheme.
Enable locking for both. Tested on n25q512ax3. The other is modified
following the datasheet.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Currently we are supporting block protection only for flash chips with
3 block protection bits (BP0-2) in the SR register.
Enable block protection support for flashes with 4 block protection bits
(BP0-3).
Add a flash_info flag for flashes that describe 4 block protection bits.
Add another flash_info flag for flashes in which BP3 bit is not adjacent
to the BP0-2 bits.
Tested with a n25q512ax3 (BP0-3) and w25q128 (BP0-2).
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The current mainline locking was restricted and could only be applied
to flashes that have 3 block protection bits and fixed locking ratio.
A new method of normalization was reached at the end of the discussion [1].
(1) - if bp slot is insufficient.
(2) - if bp slot is sufficient.
if (bp_slots_needed > bp_slots) // (1)
min_prot_length = sector_size << (bp_slots_needed - bp_slots);
else // (2)
min_prot_length = sector_size;
This patch changes logic to handle block protection based on min_prot_length.
It is suitable for the overall flashes with exception of some corner cases
(see EON and catalyst) and easy to extend and apply for the case of 2bit or
4bit block protection.
[1] http://lists.infradead.org/pipermail/linux-mtd/2020-February/093934.html
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When there are more BP settings than needed for defining the protected
areas of the flash memory, most flashes will define the remaining
settings as "protect all", i.e. the equivalent of having all the BP bits
set to one. But there are flashes where the in-between BP values
are undefined (not mentioned), and only the "all bits set" is protecting
the entire memory. One such example is w25q80, where BP[2:0]=0b101 and
0b110 are not defined.
Set all the BP bits to one when lock_len == mtd->size, to treat this
special case.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When an Erase or Program error occurs on a spansion/cypress or a
micron flash, the WEL bit remains set to one and should be cleared
with a WRDI command in order to protect against inadvertent writes
that can possible corrupt the contents of the memory.
Winbond, macronix, gd, etc., do not support the E_ERR and P_ERR bits in the
Status Register and always clear the WEL bit regardless of the outcome
of the erase or page program operation (ex w25q40bw, MX25L25635E).
Issue a WRDI command when erase or page program errors occur.
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
The SPI NOR controllers drivers must not be able to use structures that
are meant just for the SPI NOR core.
struct spi_nor_flash_parameter is filled at run-time with info gathered
from flash_info, manufacturer and sfdp data. struct spi_nor_flash_parameter
should be opaque to the SPI NOR controller drivers, make sure it is.
spi_nor_option_flags, spi_nor_read_command, spi_nor_pp_command,
spi_nor_read_command_index and spi_nor_pp_command_index are defined for the
core use, make sure they are opaque to the SPI NOR controller drivers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Cross manufacturer code is unlikely and discouraged, get rid of the
MFR definitions.
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All entries have been moved to manufacturer drivers. Get rid of this
empty table.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Create a SPI NOR manufacturer driver for XMC chips, and move the
XMC definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Xilinx chips, and move the
Xilinx definitions outside of core.c.
While at it, remove the SPI_S3AN flag which is now useless.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Catalyst chips, and move the
Catalyst definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Winbond chips, and move the
Winbond definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for SST chips, and move the
SST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Spansion chips, and move the
Spansion definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Micron/ST chips, and move the
Micron/ST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Macronix chips, and move the
Macronix definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Create a SPI NOR manufacturer driver for ISSI chips, and move the
ISSI definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Intel chips, and move the
Intel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Create a SPI NOR manufacturer driver for GigaDevice chips, and move the
GigaDevice definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Fujitsu chips, and move the
Fujitsu definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Everspin chips, and move the
Everspin definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for ESMT chips, and move the
ESMT definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Eon chips, and move the
Eon definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Atmel chips, and move the
Atmel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Declare a spi_nor_manufacturer struct and add basic building blocks to
move manufacturer specific code outside of the core.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Expose the flash_info struct and some function prototypes that
will be used by manufacturers.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
It makes the core file a bit smaller and provides better separation
between the SFDP parsing and core logic.
Keep the core.h and sfdp.h definitions private in drivers/mtd/spi-nor/.
Both expose just the definitions that are required by the core and
manufacturer drivers. None of the SPI NOR controller drivers should
include them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Move all SPI NOR controller drivers to a controllers/ sub-directory
so that we only have SPI NOR related source files under
drivers/mtd/spi-nor/.
Rename spi-nor.c into core.c, we are about to split this file in multiple
source files (one per manufacturer, plus one for the SFDP parsing logic).
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Rename (*set_4byte)() to (*set_4byte_addr_mode)() for a better
differentiation between the 4 byte address mode and opcodes.
Rename macronix_set_4byte() to spi_nor_set_4byte_addr_mode(), it will be
the only 4 byte address mode method exposed to the manufacturer drivers.
Here's how the manufacturers enter and exit the 4 byte address mode:
- eon, gidadevice, issi, macronix, xmc use EN4B/EX4B
- micron-st needs WEN. st_micron_set_4byte_addr_mode() will become
a private method, as they are the only ones that need WEN before the
EN4B/EX4B commands.
- newer spansion have a 4BAM opcode (this translates to a new, public
command). Older spansion flashes use the BRWR command (legacy in
core.c -> spansion_set_4byte_addr_mode())
- winbond's method is hackish and may be reason for just a flash
fixup hook -> private method
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Replace the manufacturer prefix by something describing more precisely
what those functions do.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
[tudor.ambarus@microchip.com: prepend spi_nor_ to all modified methods.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQmYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D9sB/9PBy5hYIWLJOqP3Tegy+si7eEjgYQe
32DvHZRYYL+Oc8OQMGnJYUY5grfriS300TjxeB4MNx8ajVyuaH7e2aIhgTz3oJ6a
YrygFcxEi0LmRT82HyLVxptyblMSo3A8QWOTOqe1aFvJRZjDDKvEIcGCW2RPmtxT
r/EoVVkSv4X+k3GUtYnRBrq12hL+vr1YIjZM05MVu2sDtFXLO2+wotFIODDv15zi
ByBtwhKumKawUOETzGDw4EDV5MJx9nZtswRC4x3hDrLS6au39F/MyP78gpHm8vw+
YfiS5/39rkB6j1QltcP3B9n7joxrgaFAYsLBTZUoE3IjeVTggcKCOSVX
=q5ml
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl5rqKYACgkQS1VPR6WN
FOltQggAvmX8EZO9DvpKr6rVhrapDgkJUT5QmwTwZfmBgp5vlRqd8AvY2IYx6/a8
yVr8TwvbJuvPKaC3PI6I9/feDYx2P5NA9fAoqy6bMACeAwuXcDwjnv/aJo74bf6d
cY2zm/heVXJ9qecPmf0msgxBpnKBaxO/u9JmyX197pHdz3vAqNq2t4w4npSqnUlJ
M/dtUxL8bIjkPeQfbV3F+2y6Ttu5hsGauy5y+spnMnMga4+tTxtokauyPBxvkllv
tqbXP5Q1C0ogByJ0rg1M7XqLb1IuCNzYo5aH20T98aCxmcUyTVnanAMX9J/rmbH8
7ykpSUYMP5WvbpRUqdIWvhmJtkPbSA==
=mMmy
-----END PGP SIGNATURE-----
Merge tag 'mtk-mtd-spi-move' into spi-nor/next
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
The mtk-quadspi driver is replaced by the new spi-mtk-nor driver.
Merge it in spi-nor/next to avoid conflicts during the release cycle.
This driver is superseded by the new spi-mtk-nor driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200306085052.28258-5-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Don't use `tmp` for two purposes (return value, loop counter).
Instead, use `i` for the loop counter, and `ret` for the return value.
- Don't use tabs between type and name in variable declarations,
for consistency with other functions in spi-nor.c.
- Rewrite nested `if`s as `if (a && b)`.
- Remove `info` variable, and use spi_nor_ids[i] directly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
[tudor.ambarus@microchip.com: change i's type from int to unsigned int,
reorder local variables]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on the original patch by Boris Brezillon
<boris.brezillon@bootlin.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_spimem_xfer_data() being a helper function for the data reads/
writes contains 3 fragments that depend on the data direction; and I'm
going to add another one to call the SPI dirmap API...
I think this function should be split so that the common fragments are
put into 2 functions, spi_nor_spimem_bounce() and spi_nor_spimem_exec_op()
called from spi_nor_spimem_{read|write}_data(), and the data direction
dependent bits moved back into those read/write functions -- that way we
would be able to avoid *goto*s otherwise needed in the next patch adding
the SPI dirmap support...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The shift variable of SR_BP is conclusive because the first bit of SR_BP
is fixed on all known flashes. Replace ffs operation with SR_BP_SHIFT.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver calls le32_to_cpu() to convert the little-endian tables
to a CPU endianness, where le32_to_cpus() should have been called.
Was going to use that one... and then discovered a whole array
converter, le32_to_cpu_array()! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
* block2mtd: page index should use pgoff_t
* maps: physmap: minimal Runtime PM support
* maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
* concat: Fix a comment referring to an unknown symbol
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Cadence: add unspecified HAS_IOMEM dependency
* Various cleanup.
Onenand
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4zMfgACgkQJWrqGEe9
VoS0xwf+KdaihRno4SkDovcHoF7K54N6CqBhwuV9uabfy4phEr38cyvaivYu0rG7
k/n3CUNRDghTh7DAUT7pBsjUeZn9XxvKyQaZz34TBgoQYwGz57ssp8lMRmJkYoA6
t9z95N9bRJ+IzZJlYELCbhNq+aOGyWYgWL+aaO0CE8OyOeWzdZumdd4k7cF7rSAu
9gWV/6iX/qP081NexfjPEVmMtNQ+0p4T7zQ01nQA7rIZiVoIgMKwBu41aRYycEEs
LeuV5gNEDn2vGBl+u85w5oF6o1TIzDeTmh0G7Jm3NQGGco2kOOZ1O39a0hrDONrA
hEoEIG/rAMKOtaLr6rCGnV/5/i/Tlw==
=WC+m
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4nSy0ACgkQJWrqGEe9
VoSr1gf+KKMtE8GabWYbKsgKRx1cmC/0pvRmp7wqjul4gd/s+llKzEDG/qMYUOua
PgynNJeP7LPIZJWqo8TjXZcNxs1E0JSoAjYK58Hm9MOIwiwmdSE7GOVxv8/1drN/
7mjJvnGznol/2GD3U4NRvW/SZHkj0/Xt9Ys70qdpcWDQWJSIUIhrNuKOMgjTP+kp
XfZ4vWL6T9LHJiIojLTkrfjXH774dWflSj8bySz+9d9kwkbvKEGU6zb6sKfGO4nm
yYqQhpUrbN8c4t+hSuJlf140haVhwCIQeujUNlTn2oDXnJIO/98k0jDSn6dpUSdx
H6NvWMa8e8Bz7HAbB7/VOawtjt/k+w==
=UPI6
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.6' into mtd/next
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for the Winbond W25Q32JW-xM flashes. These have a
programmable QE bit. There is also the W25Q32JW-xQ variant which shares
the ID with the W25Q32DW and W25Q32FW parts. The W25Q32JW-xQ has the QE
bit hard strapped to 1, thus don't support the /HOLD and /WP pins.
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller. Also the BP bits as well as the TB bit were
tested.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The commit 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc38 ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ops aren't used in any SPI NOR controller. Therefore, remove them
altogether.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-V has the same SPI serial flash controller as Kaby
Lake. Add Comet Lake-V PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver is for the HiSilicon FMC (Flash Memory Controller), which
supports SPI NOR in addition other memory technologies, like SPI NAND.
Indeed, the naming in the driver is a little inappropriate, especially
considering that there is already another HiSilicon SPI NOR flash
controller (which I believe the FMC is derived from).
Since we now want to provide software support for this other HiSilicon
controller, update code comments to at least try to make it clear that
this driver is for the FMC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Adds support for sst26vf016b, a smaller variant of the sst26vf064b.
Tested on a sama5d3 SOC using the atmel,at91rm9200-spi controller.
The dual read could not be tested.
SPI_NOR_QUAD_READ is not added because it requires that the IOC bit
from the Configuration Register to be set to 1, which is not the case:
its default value at power-up is zero and we don't set it to one in
spi-nor either.
Signed-off-by: Joseph Kust <joseph.kust@rockwellcollins.com>
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
[tudor.ambarus@microchip.com: Drop quad read flag, amend commit description]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f85 ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
c94e267766
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
refers to this bit as "bit 1 of the status register 2".
Rename the macro accordingly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Test that all the bits from Status Register 1 and Status Register 2
were written correctly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_unlock() unlocks blocks of memory or the entire flash memory
array, if requested. clear_sr_bp() unlocks the entire flash memory
array at boot time. This calls for some unification, clear_sr_bp() is
just an optimization for the case when the unlock request covers the
entire flash size.
Get rid of clear_sr_bp() and introduce spi_nor_unlock_all(), which is
just a call to spi_nor_unlock() for the entire flash memory array.
This fixes a bug that was present in spi_nor_spansion_clear_sr_bp().
When the QE bit was zero, we used the Write Status (01h) command with
one data byte, which might cleared the Status Register 2. We now always
use the Write Status (01h) command with two data bytes when
SNOR_F_HAS_16BIT_SR is set, to avoid clearing the Status Register 2.
The SNOR_F_NO_READ_CR case is treated as well. When the flash doesn't
support the CR Read command, we make an assumption about the value of
the QE bit. In spi_nor_init(), call spi_nor_quad_enable() first, then
spi_nor_unlock_all(), so that at the spi_nor_unlock_all() time we can
be sure the QE bit has value one, because of the previous call to
spi_nor_quad_enable().
Get rid of the MFR handling and implement specific manufacturer
default_init() fixup hooks.
Note that this changes a bit the logic for the SNOR_MFR_ATMEL,
SNOR_MFR_INTEL and SNOR_MFR_SST cases. Before this patch, the Atmel,
Intel and SST chips did not set the locking ops, but unlocked the entire
flash at boot time, while now they are setting the locking ops to
stm_locking_ops. This should work, since the disable of the block
protection at the boot time used the same Status Register bits to unlock
the flash, as in the stm_locking_ops case.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Make sure that when doing a lock() or an unlock() operation we don't clear
the QE bit from Status Register 2.
JESD216 revB or later offers information about the *default* Status
Register commands to use (see BFPT DWORDS[15], bits 22:20). In this
standard, Status Register 1 refers to the first data byte transferred on a
Read Status (05h) or Write Status (01h) command. Status register 2 refers
to the byte read using instruction 35h. Status register 2 is the second
byte transferred in a Write Status (01h) command.
Industry naming and definitions of these Status Registers may differ.
The definitions are described in JESD216B, BFPT DWORDS[15], bits 22:20.
There are cases in which writing only one byte to the Status Register 1
has the side-effect of clearing Status Register 2 and implicitly the Quad
Enable bit. This side-effect is hit just by the
BFPT_DWORD15_QER_SR2_BIT1_BUGGY and BFPT_DWORD15_QER_SR2_BIT1 cases.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Check that all the bits written in the write_sr_and_check() method
match the status_new received value. Failing to write the other bits
is dangerous too, extend the check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
When the Read-Modify-Write-Read-Back Quad Enable methods failed on
the Read-Back, they returned -EINVAL. Since this is an I/O error,
return -EIO.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop the default spansion_quad_enable() method and replace it with
spansion_read_cr_quad_enable().
The function was buggy, it didn't care about the previous values
of the Status and Configuration Registers. spansion_read_cr_quad_enable()
is a Read-Modify-Write-Check function that keeps track of what were
the previous values of the Status and Configuration Registers.
In terms of instruction types sent to the flash, the only difference
between the spansion_quad_enable() and spansion_read_cr_quad_enable()
is that the later calls spi_nor_read_sr(). We can safely assume that all
flashes support spi_nor_read_sr(), because all flashes call it in
spi_nor_sr_ready(). The transition from spansion_quad_enable() to
spansion_read_cr_quad_enable() will not affect anybody, drop the buggy
code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
static int spi_nor_write_sr(struct spi_nor *nor, u8 val)
static int spi_nor_write_sr_cr(struct spi_nor *nor, const u8 *sr_cr)
into
static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
The Status Register can be written with one or two bytes. Merge
the two functions to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.
Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Check for the return vales of each Register Operation.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.
Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.
Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.
Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.
Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: Jethro Beekman <jethro@fortanix.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
n25q512a was rebranded to mt25qu512a after its spin off from STM.
mt25qu512a is different only in terms of operating frequency, the
JEDEC id is the same as in n25q512a.
Dual reads are supported (0x3b, 0x3c), set the SPI_NOR_DUAL_READ flag.
4-byte opcodes are supported, set the SPI_NOR_4B_OPCODES flag.
Tested Single I/O and QUAD I/O mode on LS1046FRWY.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: rename entry to "mt25qu512a (n25q512a)",
reword commit message, order entry by size, drop comment as it looked
redundant]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We already pass a pointer to nor, we can obtain the sector_size
by dereferencing it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch adds spi_nor_debugfs_init() for the debugfs initialization.
With this patch, we can read the partname and partid through the
debugfs.
The output of new debugfs nodes on my device are:
cat /sys/kernel/debug/mtd/mtd0/partid
spi-nor:ef6017
cat /sys/kernel/debug/mtd/mtd0/partname
w25q64dw
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put before
the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there is
no put, thus causing a memory leak. Upon termination of the loop
(whether by break or a natural exit), either ret will have a non-zero
value or child will be NULL. Hence add an of_node_put() that will
execute only when ret has a non-zero value, as calling of_node_put() on
a possible NULL value does not cause any further issues.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Dedicate a function for getting the pointer to the flash_info
const struct. Trim a bit the spi_nor_scan() huge function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Parsing of flash parameters were interleaved with setting of the
nor addr width. Dedicate a function for setting nor addr width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
S3AN flashes use a specific opcode to read the status register.
We currently use the SPI_S3AN flag to decide whether this specific
SR read opcode should be used, but SPI_S3AN is about to disappear, so
let's add a new flag.
Note that we use the same bit as SPI_S3AN implies SPI_NOR_XSR_RDY and
vice versa.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
s3an_nor_scan() was overriding the opcode selection done in
spi_nor_default_setup(). Set nor->setup() method in order to
avoid the unnecessary call to spi_nor_default_setup().
Now that the call to spi_nor_default_setup() is skipped, set
mtd.erasesize to nor->info->sector_size, as it was when
spi_nor_select_erase() was called.
No dummy byte is required for the S3AN's Random Read command (0x03),
so no need to set nor->read_dummy.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
