Apart from a binding conversion to yaml, only minor changes/small fixes
have been merged.
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
* SPI NOR changes:
A notable changes is the fix for exiting 4-byte addressing on Infineon
SEMPER flashes. These flashes do not support the standard EX4B
opcode (E9h), and use a vendor-specific opcode (B8h) instead.
There is also a fix for unlocking flashes that are write-protected at
power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmiLn/sACgkQJWrqGEe9
VoTGowf/c6kynDuMlQbTANv/UIYX/LRFZsnIx0LB32LWrhLaUIBsbFxejyt07WG9
ryej+xRUtSHGsqMIw+B/PjvA4hUNLdsSwO/udIwstXNQjJcO9OKp/ucpvlxLzIha
REq8IifvT9vLLA+Efoq2L25dM14KjuFCAjwm3GH/SmdTOqPhI/Bbnx4vRWIPeXrx
XZ69ovIiu5NqLTD5IFGsu+omhbFWlDtVALtKNknrTOXWrjLZhDpieO4f7M9rvru6
OwazFQAWuixzqZRMFqvOzu8KUDnOHi9gHrzi6tS7T1zBUDz9ywdBtaHYCd7VlMJh
uV1wjUdWjnIh9E8R/llv3D+ko1Ya1w==
=IS/d
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- Apart from a binding conversion to yaml, only minor changes/small
fixes have been merged.
Raw NAND changes:
- Minor fixes for various controller drivers like DMA mapping checks,
better timing derivations or bitflip statistics.
- some Hynix NAND flashes were not supporting read-retries, so don't
even try to do it
SPI NAND changes:
- In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
- Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
SPI NOR changes:
- A notable changes is the fix for exiting 4-byte addressing on
Infineon SEMPER flashes. These flashes do not support the standard
EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.
- There is also a fix for unlocking flashes that are write-protected
at power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all()"
* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
mtd: spinand: winbond: Add comment about the maximum frequency
mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
mtd: spinand: Add a ->configure_chip() hook
mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
mtd: spinand: Fix macro alignment
spi: spi-mem: Take into account the actual maximum frequency
spi: spi-mem: Use picoseconds for calculating the op durations
mtd: rawnand: atmel: set pmecc data setup time
mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
mtd: rawnand: fsmc: Add missing check after DMA map
mtd: rawnand: rockchip: Add missing check after DMA map
mtd: rawnand: hynix: don't try read-retry on SLC NANDs
mtd: rawnand: atmel: Fix dma_mapping_error() address
mtd: nand: brcmnand: fix mtd corrected bits stat
mtd: rawnand: renesas: Add missing check after DMA map
mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
mtd: nand: brcmnand: replace manual string choices with standard helpers
mtd: map: Don't use "proxy" headers
mtd: spi-nor: Fix spi_nor_try_unlock_all()
...
Commit ff67592cbd ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
moved all initialization of the mtd fields at the end of spi_nor_scan().
Normally, the mtd info is only needed for the mtd ops on the device,
with one exception: spi_nor_try_unlock_all(), which will also make use
of the mtd->size parameter. With that commit, the size will always be
zero because it is not initialized. Fix that by not using the size of
the mtd_info struct, but use the size from struct spi_nor_flash_parameter.
Fixes: ff67592cbd ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
Cc: stable@vger.kernel.org
Reported-by: Jean-Marc Ranger <jmranger@hotmail.com>
Closes: https://lore.kernel.org/all/DM6PR06MB561177323DC5207E34AF2A06C547A@DM6PR06MB5611.namprd06.prod.outlook.com/
Tested-by: Jean-Marc Ranger <jmranger@hotmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250701140426.2355182-1-mwalle@kernel.org
Infineon SEMPER flash family does not support E9h opcode as Exit 4-byte
mode (EX4B). Therefore, params->set_4byte_addr_mode is not determined by
BFPT parse. Fixup it up by introducing vendor specific EX4B opcode (B8h)
and function.
Fixes: c87c9b11c5 ("mtd: spi-nor: spansion: Determine current address mode")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250612074427.22263-1-Takahiro.Kuwano@infineon.com
'struct spi_nor_fixups' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
23304 13168 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
After:
=====
text data bss dec hex filename
23560 12912 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/aa641732ba707ce3690217825c3ca7373ffde4f9.1748191985.git.christophe.jaillet@wanadoo.fr
SFDP of MX25L3255E is JESD216, which does not include the Quad
Enable bit Requirement in BFPT. As a result, during BFPT parsing,
the quad_enable method is not set to spi_nor_sr1_bit6_quad_enable.
Therefore, it is necessary to correct this setting by late_init.
In addition, MX25L3255E also supports 1-4-4 page program in 3-byte
address mode. However, since the 3-byte address 1-4-4 page program
is not defined in SFDP, it needs to be configured in late_init.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: move params declaration to top, and use it everywhere]
Link: https://lore.kernel.org/r/20250407075400.1113177-4-linchengming884@gmail.com
To clean up the code and reduce duplication, this entry is removed.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250407075400.1113177-3-linchengming884@gmail.com
Many flash devices share the same ID but have different part numbers.
To avoid confusion, the part number field is removed.
Additionally, since SFDP already provides size information and
functionality covered by no_sfdp_flags, these fields are also removed.
Furthermore, when 4-byte address instruction table is available,
the SPI_NOR_4B_OPCODES flag is no longer needed and is removed.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250407075400.1113177-2-linchengming884@gmail.com
The atmel,dataflash binding has been converted to yaml and the physmap
one constrained. Some logs are improved, error path are getting reworked
a bit, few patches target the use of str_enabled_disabled().
* Raw NAND changes:
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
* SPI NOR changes:
Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start using
the scope based mutex cleanup helpers.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmfkMTQACgkQJWrqGEe9
VoS+Fgf/apT4C5115f4EolKAcato3QpJ+J1+S0Oy6yYSKQVwKNa4NkdBIeKXfQLc
rjNdsoE9RmibCKViX3D3rjlMnynbkIr4F3YHbgP4lz7y2TQUVA7Dy0sp2RX+9M3G
+a5u6lfUyGA/uzJPJUESaPpjLWLg5uTRcduD8hGVid9D+/KFYWNF0EsufobT8JmT
X/R+aVS58W0uqLEJtiaINsD6D3f8ukMZCNgsvuAUINSUNUrX61pVQZwQAZ4eCCNa
W+YaLdsMtrwRBdoRGXfrElHEvnufglYocUo+9h8EOVMQ84rfNH363Nu+1WxTVGDj
GLB5O9knQFy7DR0M4gYBAqqji41nTg==
=O/Ud
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- The atmel,dataflash binding has been converted to yaml and the
physmap one constrained. Some logs are improved, error path are
getting reworked a bit, few patches target the use of
str_enabled_disabled().
Raw NAND changes:
- i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
SPI NAND changes:
- OTP support has been brought, and ESMT and Micron manufacturer
drivers implement it.
- Read retry, and Macronix manufacturer driver implement it.
SPI NOR changes:
- Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start
using the scope based mutex cleanup helpers.
There is also a bunch of minor improvements and fixes in drivers
and bindings"
* tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (34 commits)
dt-bindings: mtd: atmel,dataflash: convert txt to yaml
mtd: mchp48l640: Use str_enable_disable() in mchp48l640_write_prepare()
mtd: rawnand: gpmi: Use str_enabled_disabled() in gpmi_nand_attach_chip()
mtd: mtdpart: Do not supply NULL to printf()
dt-bindings: mtd: gpmi-nand: Add compatible string for i.MX8 chips
mtd: nand: Fix a kdoc comment
mtd: spinand: Improve spinand_info macros style
mtd: spi-nor: drop unused <linux/of_platform.h>
mtd: spi-nor: explicitly include <linux/of.h>
mtd: spi-nor: explicitly include <linux/math64.h>
mtd: spi-nor: macronix: add support for mx66{l2, u1}g45g
mtd: spi-nor: macronix: Add post_sfdp fixups for Quad Input Page Program
mtd: Fix error handling in mtd_device_parse_register() error path
mtd: capture device name setting failure when adding mtd
mtd: Add check for devm_kcalloc()
mtd: Replace kcalloc() with devm_kcalloc()
dt-bindings: mtd: physmap: Ensure all properties are defined
mtd: rawnand: brcmnand: fix PM resume warning
dt-bindings: mtd: mxc-nand: Document fsl,imx31-nand
mtd: spinand: macronix: Add support for read retry
...
The core driver is using of_property_read_bool() and relies on implicit
inclusion of <linux/of.h>, which comes from <linux/mtd/mtd.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250307-spi-nor-headers-cleanup-v1-1-c186a9511c1e@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
swp and otp drivers use div_u64 and div64_u64 and rely on implicit
inclusion of <linux/math64.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250223-snor-math64-v2-1-6f0313eea331@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Due to incorrect values in the 4-BAIT table for these two flash IDs,
it is necessary to add these two flash IDs with fixups.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20250211063028.382169-3-linchengming884@gmail.com
[ta: update commit subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Although certain Macronix NOR flash support the Quad Input Page Program
feature, the corresponding information in the 4-byte Address Instruction
Table of these flash is not properly filled. As a result, this feature
cannot be enabled as expected.
To address this issue, a post_sfdp fixups implementation is required to
correct the missing information.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20250211063028.382169-2-linchengming884@gmail.com
[ta: fix alignment to match open parenthesis]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Sorting headers alphabetically helps locating duplicates,
and makes it easier to figure out where to insert new headers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250211-spi-nor-guard-mutex-v1-1-05ed77a484d9@linaro.org
Add support for Winbond w25q01jv spi-nor chip.
This chip is internally made of two dies with linear addressing
capabilities to make it transparent to the user that two dies were
used. There is one drawback however, the read status operation is racy
as the status bit only gives the active die status and not the status of
the other die. For commands affecting the two dies, it means if another
command is sent too fast after the first die has returned a valid status
(deviation can be up to 200us), the chip will get corrupted/in an
unstable state.
This chip hence requires a better status register read. There are three
solutions here:
1- If we assume that the most common situation producing this problem is
status register writes, maybe we could change the "non-volatile"
status register write commands to become "volatile" status register
writes. In practice, what takes time is the write operation of the bits
themselves, and not the activation of the feature in the internal
circuitry. Enabling "volatile" status register writes would make the
writes nearly instant.
This approach, besides probably being the less impacting one, could
overlook other possible actions where both dies can be used at the same
time like a chip erase (or any erase over die boundaries in general).
2- Wait about 200us after getting a first status ready feedback. This
200us is about the maximum possible deviation between dies and would
cover all cases.
3- We iterate manually over all internal dies (which takes about 30us
per die) until all are ready. This approach will always be faster than
a blind delay which represents the maximum deviation, while also being
totally safe.
This third approach has been adopted. A flash-specific hook for the
status register read had to be implemented. Testing with the flash_speed
benchmark shown no difference with the existing performances (using the
regular status read core function). In practice there are difference in
the experimental results below, but they are part of the natural
deviation of the benchmark:
> Without the fixup
$ flash_speed /dev/mtd0 -c100 -d
eraseblock write speed is 442 KiB/s
eraseblock read speed is 1606 KiB/s
page write speed is 439 KiB/s
page read speed is 1520 KiB/s
2 page write speed is 441 KiB/s
2 page read speed is 1562 KiB/s
erase speed is 68 KiB/s
> With the fixup
$ flash_speed /dev/mtd0 -c100 -d
eraseblock write speed is 428 KiB/s
eraseblock read speed is 1626 KiB/s
page write speed is 426 KiB/s
page read speed is 1538 KiB/s
2 page write speed is 426 KiB/s
2 page read speed is 1574 KiB/s
erase speed is 66 KiB/s
However, the fixup, whatever which one we pick, must be applied on
multi-die chips, which hence must be properly flagged. The SFDP tables
implemented give a lot of information but the die details are part of an
optional table that is not implemented, hence we use a post parsing
fixup hook to set the params->n_dice value manually.
Link: https://www.winbond.com/resource-files/W25Q01JV%20SPI%20RevE%2003042024%20Plus.pdf
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250110-winbond-6-12-rc1-nor-volatile-bit-v3-1-735363f8cc7d@bootlin.com
There's been no major core change, and a bunch of driver related
improvements, amongst them the conversion to of_property_present() for
non-boolean properties, the addition of the support for Fujitsu
MB85RS128TY FRAM, a couple of improvements to the phram driver and the
usual load of misc changes.
* Raw NAND changes
A new controller driver, from Nuvoton, has been merged.
Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also on the
performance side. The binding has also been converted to yaml, received
a new OOB layout and now supports on-die ECC engines.
The Qualcomm controller driver has been deeply cleaned to extract some
parts of the code into a shared file with the Qualcomm SPI memory
controller.
Aside from these main changes, the Cadence binding has been converted to
yaml, the brcmnand controller driver has received a small fix, otherwise
some more minor changes have also made their way in.
* SPI NAND changes
The SPI NAND subsystem has seen a great improvement, with the advent of
DTR operations (DDR operations, which may be extended to the address
cycles). The first vendor driver to benefit from these improvements is
the Winbond driver.
A new manufacturer driver is added SkyHigh, with a new constraint for
the core, it is impossible to disable the on-die ECC engine.
A Foresee device is also now supported.
* SPI NOR changes
Several flash entries have been added: Atmel AT25SF321, Spansion
S28HL256T and S28HL02GT.
Support for vcc-supply regulators and their DT bindings has been added.
The mx25u25635f entry has been dropped. The flash shares its ID with
mx25u25645g and both parts have an SFDP table. Removing their entry lets
them be driven by the generic SFDP-based driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmeTZO0ACgkQJWrqGEe9
VoSW1Qf/f96ejqjzTenBHYKOdSqm6aoML17po1xAUubIViub6LJQBHHrj69qvCvj
A4LrqQBPrnH1Escw79QEdwtTrefqra7CHnR1mMrhgF9SCS90762tt+MZ3+GDawBD
CU/Zw86+FrFyH1wRZg6RFT+FEGHBIExi7FqpypBLARdYrGt8ZpNDhJuPHizhvyco
Whd2WCoQEYxRsPQr+tcAuTtymCRSrNQ+IalVoTfm7p0QHS3OGfJWHHS92FPwTs/H
p2TvkEY/HD4pSelseJhG7nWA+CgfxyTg0pzISi2Ctr3qH76AHTDRZBm1xBKY/NiY
ZfC1YJ3cAjyN+VfL897DopAqmZK+3g==
=mk21
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- There's been no major core change, just a bunch of driver related
improvements.
Amongst them the conversion to of_property_present() for
non-boolean properties, the addition of the support for Fujitsu
MB85RS128TY FRAM, a couple of improvements to the phram driver and
the usual load of misc changes.
Raw NAND changes:
- A new controller driver, from Nuvoton, has been merged
- Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also
on the performance side. The binding has also been converted to
yaml, received a new OOB layout and now supports on-die ECC engines
- The Qualcomm controller driver has been deeply cleaned to extract
some parts of the code into a shared file with the Qualcomm SPI
memory controller
- Aside from these main changes, the Cadence binding has been
converted to yaml, the brcmnand controller driver has received a
small fix, otherwise some more minor changes have also made their
way in
SPI NAND changes:
- The SPI NAND subsystem has seen a great improvement, with the
advent of DTR operations (DDR operations, which may be extended to
the address cycles). The first vendor driver to benefit from these
improvements is the Winbond driver
- A new manufacturer driver is added SkyHigh, with a new constraint
for the core, it is impossible to disable the on-die ECC engine
- A Foresee device is also now supported
SPI NOR changes:
- Several flash entries have been added: Atmel AT25SF321, Spansion
S28HL256T and S28HL02GT
- Support for vcc-supply regulators and their DT bindings has been
added
- The mx25u25635f entry has been dropped. The flash shares its ID
with mx25u25645g and both parts have an SFDP table. Removing their
entry lets them be driven by the generic SFDP-based driver"
* tag 'mtd/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (47 commits)
mtd: spinand: skyhigh: Align with recent read from cache variant changes
mtd: spinand: winbond: Add support for DTR operations
mtd: spinand: winbond: Add comment about naming
mtd: spinand: winbond: Update the *JW chip definitions
mtd: spinand: Add support for read DTR operations
mtd: spinand: Enhance the logic when picking a variant
mtd: spinand: Add an optional frequency to read from cache macros
mtd: spinand: Create distinct fast and slow read from cache variants
mtd: hyperbus: Use of_property_present() for non-boolean properties
mtd: st_spi_fsm: Switch from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
mtd: rawnand: davinci: add ROM supported OOB layout
mtd: spi-nor: sysfs: constify 'struct bin_attribute'
mtd: spi-nor: spansion: Add support for S28HL02GT
mtd: spi-nor: spansion: Add support for S28HL256T
mtd: spi-nor: extend description of size member of struct flash_info
mtd: rawnand: davinci: Reduce polling interval in NAND_OP_WAITRDY_INSTR
mtd: rawnand: qcom: Fix build issue on x86 architecture
mtd: rawnand: qcom: use FIELD_PREP and GENMASK
mtd: nand: Add qpic_common API file
mtd: rawnand: qcom: Add qcom prefix to common api
...
This reverts commit 98d1fb94ce.
The commit uses data nbits instead of addr nbits for dummy phase. This
causes a regression for all boards where spi-tx-bus-width is smaller
than spi-rx-bus-width. It is a common pattern for boards to have
spi-tx-bus-width == 1 and spi-rx-bus-width > 1. The regression causes
all reads with a dummy phase to become unavailable for such boards,
leading to a usually slower 0-dummy-cycle read being selected.
Most controllers' supports_op hooks call spi_mem_default_supports_op().
In spi_mem_default_supports_op(), spi_mem_check_buswidth() is called to
check if the buswidths for the op can actually be supported by the
board's wiring. This wiring information comes from (among other things)
the spi-{tx,rx}-bus-width DT properties. Based on these properties,
SPI_TX_* or SPI_RX_* flags are set by of_spi_parse_dt().
spi_mem_check_buswidth() then uses these flags to make the decision
whether an op can be supported by the board's wiring (in a way,
indirectly checking against spi-{rx,tx}-bus-width).
Now the tricky bit here is that spi_mem_check_buswidth() does:
if (op->dummy.nbytes &&
spi_check_buswidth_req(mem, op->dummy.buswidth, true))
return false;
The true argument to spi_check_buswidth_req() means the op is treated as
a TX op. For a board that has say 1-bit TX and 4-bit RX, a 4-bit dummy
TX is considered as unsupported, and the op gets rejected.
The commit being reverted uses the data buswidth for dummy buswidth. So
for reads, the RX buswidth gets used for the dummy phase, uncovering
this issue. In reality, a dummy phase is neither RX nor TX. As the name
suggests, these are just dummy cycles that send or receive no data, and
thus don't really need to have any buswidth at all.
Ideally, dummy phases should not be checked against the board's wiring
capabilities at all, and should only be sanity-checked for having a sane
buswidth value. Since we are now at rc7 and such a change might
introduce many unexpected bugs, revert the commit for now. It can be
sent out later along with the spi_mem_check_buswidth() fix.
Fixes: 98d1fb94ce ("mtd: spi-nor: core: replace dummy buswidth from addr to data")
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/linux-mtd/3342163.44csPzL39Z@steina-w/
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-mtd-v1-1-ee13140a4e9b@weissschuh.net
We use the size as an indicator whether to parse SFDP or not. We don't
introduce a dedicated member for SFDP parsing because we'd like to keep
the struct size at a minimum, as it's used for every flash declaration.
Ideally we won't have flash entries at all, but there are still flash
parameters that aren't defined by SFDP, thus we need to statically
specify them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241219-spi-nor-flash-info-size-desc-v1-1-6b53cf011027@linaro.org
The Macronix mx25u25635f flash device supports SFDP initialization.
This commit removes the specific mx25u25635f entry (NOR ID 0xc22539),
along with its size and flags, from the NOR parts list. By removing
this entry, both mx25u25635f and mx25u25645g (which share the same
NOR ID) will utilize the generic flash driver configuration.
This change allows both devices (mx25u25635f and mx25u25645g) to
leverage SFDP-defined parameters, enabling dual and quad read
operations without the need for manual adjustment of no_sfdp_flags.
Link: https://www.macronix.com/Lists/Datasheet/Attachments/8663/MX25U25635F,%201.8V,%20256Mb,%20v1.5.pdf
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241105105844.257676-1-parth105105@gmail.com
SPI NOR flashes needs power supply to work properly. The power supply
maybe software controllable per board design. So add the support
for an vcc-supply regulator.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
[ta: move devm_regulator_get_enable() to spi_nor_probe().]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111111946.9048-3-tudor.ambarus@linaro.org
Use a local variable for the struct device pointers to avoid
dereferencing.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111111946.9048-2-tudor.ambarus@linaro.org
Use the nor->addr_nbytes set by the core, we shouldn't use
magic numbers or states that are not tracked by the core.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111113609.12093-1-tudor.ambarus@linaro.org
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
it: macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary
when configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the controllers
swap the bytes back at runtime. This avoids breaking the boot sequence
because of the endianness problems that appear when the bootloaders use
1-1-1 and the kernel uses 8D-8D-8D with byte swap support. Along with the
SPI MEM byte swap support we queue a patch for the SPI MXIC controller
that swaps the bytes back at runtime.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmczG/oACgkQS1VPR6WN
FOnTCAf/YjH9AimQAFJLRKoGqsf6boh1JppcRh1YTRS+D6+Ap9+s1gJoZZYs5VWA
vNfBzGqDXknBvpmOgoXnuDu2zFs9FUvdN5Kf7w6LiS5qtz7uOxHdVoDQyDgnN6w5
9ts7qF7LViBHg/HgTEzQT2Zj6qmvIwUbccIkmJeehWjEP/urzOML5nPnM9g4HZVB
W8B5KQ4TiOY1GxkXvIP6EQS6mDKznP3yl2Hnsmk0HPpSm6D807O2zvT+z1SCxpjy
C8+mYRKsRxHoFGL6UzWgqREGBn2wzF7Ral1CR9SpSZZLLtr6S0shqRzKiiH8eiZK
1hFpXzMS3OWi4a/5724AWaqcR0Qgqw==
=jf3Q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR introduces byte swap support for 8D-8D-8D mode and a user for
it: macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary
when configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the controllers
swap the bytes back at runtime. This avoids breaking the boot sequence
because of the endianness problems that appear when the bootloaders use
1-1-1 and the kernel uses 8D-8D-8D with byte swap support. Along with the
SPI MEM byte swap support we queue a patch for the SPI MXIC controller
that swaps the bytes back at runtime.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmczG/oACgkQS1VPR6WN
# FOnTCAf/YjH9AimQAFJLRKoGqsf6boh1JppcRh1YTRS+D6+Ap9+s1gJoZZYs5VWA
# vNfBzGqDXknBvpmOgoXnuDu2zFs9FUvdN5Kf7w6LiS5qtz7uOxHdVoDQyDgnN6w5
# 9ts7qF7LViBHg/HgTEzQT2Zj6qmvIwUbccIkmJeehWjEP/urzOML5nPnM9g4HZVB
# W8B5KQ4TiOY1GxkXvIP6EQS6mDKznP3yl2Hnsmk0HPpSm6D807O2zvT+z1SCxpjy
# C8+mYRKsRxHoFGL6UzWgqREGBn2wzF7Ral1CR9SpSZZLLtr6S0shqRzKiiH8eiZK
# 1hFpXzMS3OWi4a/5724AWaqcR0Qgqw==
# =jf3Q
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Nov 2024 10:12:26 AM CET
# gpg: using RSA key 1D422ACACF0EC86D5E1DFEDF4B554F47A58D14E9
# gpg: Good signature from "Tudor Ambarus (4096-bit rsa key) <tudor.ambarus@microchip.com>" [full]
# gpg: aka "Tudor Ambarus <tudor.ambarus@gmail.com>" [full]
# gpg: tudor.ambarus@microchip.com: Verified 15 signatures in the past 5 years.
# Encrypted 0 messages.
# gpg: tudor.ambarus@gmail.com: Verified 15 signatures in the past 5 years.
# Encrypted 0 messages.
The default dummy cycle for Macronix SPI NOR flash in Octal Output
Read Mode(1-1-8) is 20.
Currently, the dummy buswidth is set according to the address bus width.
In the 1-1-8 mode, this means the dummy buswidth is 1. When converting
dummy cycles to bytes, this results in 20 x 1 / 8 = 2 bytes, causing the
host to read data 4 cycles too early.
Since the protocol data buswidth is always greater than or equal to the
address buswidth. Setting the dummy buswidth to match the data buswidth
increases the likelihood that the dummy cycle-to-byte conversion will be
divisible, preventing the host from reading data prematurely.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Cc: stable@vger.kernel.org
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20241112075242.174010-2-linchengming884@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Commit d35df77707 ("mtd: spi-nor: winbond: fix w25q128 regression")
upstream fixed a regression for flavors of 0xef4018 flash that don't
define SFDP tables. Add a comment on the flash definition highlighting
that there are flavors of flashes with and without SFDP support.
It spares developers searching the entire git log for when we'll better
handle these cases.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241029080049.96679-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In octal DTR mode, RD_ANY_REG_OP needs to use 4-byte address regardless
of flash's internal address mode. Use nor->addr_nbytes which is set to 4
during setup.
Fixes: eff9604390 ("mtd: spi-nor: spansion: add octal DTR support in RD_ANY_REG_OP")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20241016000837.17951-1-Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
Add manufacturer ID 0xc2 at the end of ID table to allow manufacturer
fixups to be applied for any Macronix flash. This spares us of adding
new flash entries for flashes that can be initialized solely based on
the SFDP data, but still need the manufacturer hooks to set parameters
that can't be discovered at SFDP parsing time.
The ID is added in order to set the octal DTR methods. SFDP defines a
"Command Sequences to Change to Octal DDR (8D-8D-8D) Mode" which can
enable the octal DTR mode. Until that is parsed and used, use the
local defined method.
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-7-alvinzhou.tw@gmail.com
[ta: update commit message and comment in the code]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Parse BFPT in order to retrieve the byte order in 8D-8D-8D mode.
This info flag will be used as a basis to determine whether
there is byte swapping of data for SPI NOR flash in octal
DTR mode.
The controller driver will check whether byte swapping is supported
to determine whether the corresponding operation are supported,
thus avoiding the generation of unexpected data order.
Merge Tudor's patch and add modifications for suiting newer version
of Linux kernel.
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-5-alvinzhou.tw@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Macronix swaps bytes on a 16-bit boundary when configured in Octal DTR.
The byte order of 16-bit words is swapped when read or written in 8D-8D-8D
mode compared to STR modes. Allow operations to specify the byte order in
DTR mode, so that controllers can swap the bytes back at run-time to
address the flash's endianness requirements, if they are capable. If the
controller is not capable of swapping the bytes, the protocol is downgrade
via spi_nor_spimem_adjust_hwcaps(). When available, the swapping of the
bytes is always done regardless if it's a data or register access, so that
it comply with the JESD216 requirements: "Byte order of 16-bit words is
swapped when read in 8D-8D-8D mode compared to 1-1-1".
Merge Tudor's patch and add modifications for suiting newer version
of Linux kernel.
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-4-alvinzhou.tw@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Create Macronix specify method for enable Octal DTR mode and
set 20 dummy cycles to allow running at the maximum supported
frequency for Macronix Octal flash.
Use number of dummy cycles which is parse by SFDP then convert
it to bit pattern and set in CR2 register.
Set CR2 register for enable octal DTR mode.
Use Read ID to confirm that enabling/disabling octal DTR mode
was successful.
Macronix ID format is A-A-B-B-C-C in octal DTR mode.
To ensure the successful enablement of octal DTR mode, confirm
that the 6-byte data is entirely correct.
Co-developed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-2-alvinzhou.tw@gmail.com
Fix flash probing by name. Flash entries without a name are allowed
since commit 15eb8303bb ("mtd: spi-nor: mark the flash name as
obsolete"). But it was just until recently that a flash entry without a
name was actually introduced. This triggers a bug in the legacy probe by
name path. Skip entries without a name to fix it.
Fixes: 2095e7da8049 ("mtd: spi-nor: spansion: Add support for S28HS256T")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/r/66c8ebb0-1324-4ad9-9926-8d4eb7e1e63a@nvidia.com/
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240909072854.812206-1-mwalle@kernel.org
These flash chips are used on Google / TP-Link / ASUS OnHub devices, and
OnHub devices are write-protected by default (same as any other
ChromeOS/Chromebook system). I've referred to datasheets, and tested on
OnHub devices.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240726185825.142733-1-computersforpeace@gmail.com
Writing to the Flash in `sst_nor_write()` is a 3-step process:
first an optional one-byte write to get 2-byte-aligned, then the
bulk of the data is written out in vendor-specific 2-byte writes.
Finally, if there's a byte left over, another one-byte write.
This was implemented 3 times in the body of `sst_nor_write()`.
To reduce code duplication, factor out these sub-steps to their
own function.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: fixup whitespace, use %zu instead of %i in WARN()]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240710091401.1282824-1-csokas.bence@prolan.hu
Commit 83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
removed the flags for non-SFDP devices. It was assumed that it wasn't in
use anymore. This wasn't true. Add the no_sfdp_flags as well as the size
again.
We add the additional flags for dual and quad read because they have
been reported to work properly by Hartmut using both older and newer
versions of this flash, the similar flashes with 64Mbit and 256Mbit
already have these flags and because it will (luckily) trigger our
legacy SFDP parsing, so newer versions with SFDP support will still get
the parameters from the SFDP tables.
Reported-by: Hartmut Birr <e9hack@gmail.com>
Closes: https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/
Fixes: 83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240621120929.2670185-1-mwalle@kernel.org
Rework spi_nor_get_flash_info() to make it look more straight forward
and esp. don't return early. The latter is a preparation to check for
deprecated flashes.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240603134055.1859863-1-mwalle@kernel.org
The Everspin FRAM devices are the only user of the NO_FR flag. Drop the
global flag and instead use a manufacturer fixup for the Everspin
flashes to drop the fast read support.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: s/evervision/everspin/g in code and commit message]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-5-mwalle@kernel.org
With the removal of the Xilinx flashes, there is no more flash driver
using that hook. The original intention was to let the driver configure
special requirements like page size an opcodes. This is already
possible by other means and it is unlikely a flash will overwrite the
(more or less complex) setup function.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-4-mwalle@kernel.org
