Logitech C922 internal SOF does not increases at a stable rate of 1kHz.
This causes that the device_sof and the host_sof run at different rates,
breaking the clock domain conversion algorithm. Eg:
30 (6) [-] none 30 614400 B 21.245557 21.395214 34.133 fps ts mono/SoE
31 (7) [-] none 31 614400 B 21.275327 21.427246 33.591 fps ts mono/SoE
32 (0) [-] none 32 614400 B 21.304739 21.459256 34.000 fps ts mono/SoE
33 (1) [-] none 33 614400 B 21.334324 21.495274 33.801 fps ts mono/SoE
* 34 (2) [-] none 34 614400 B 21.529237 21.527297 5.130 fps ts mono/SoE
* 35 (3) [-] none 35 614400 B 21.649416 21.559306 8.321 fps ts mono/SoE
36 (4) [-] none 36 614400 B 21.678789 21.595320 34.045 fps ts mono/SoE
...
99 (3) [-] none 99 614400 B 23.542226 23.696352 33.541 fps ts mono/SoE
100 (4) [-] none 100 614400 B 23.571578 23.728404 34.069 fps ts mono/SoE
101 (5) [-] none 101 614400 B 23.601425 23.760420 33.504 fps ts mono/SoE
* 102 (6) [-] none 102 614400 B 23.798324 23.796428 5.079 fps ts mono/SoE
* 103 (7) [-] none 103 614400 B 23.916271 23.828450 8.478 fps ts mono/SoE
104 (0) [-] none 104 614400 B 23.945720 23.860479 33.957 fps ts mono/SoE
Instead of disabling completely the hardware timestamping for such
hardware we take the assumption that the packet handling jitter is
under 2ms and use the host_sof as dev_sof.
We can think of the UVC hardware clock as a system with a coarse clock
(the SOF) and a fine clock (the PTS). The coarse clock can be replaced
with a clock on the same frequency, if the jitter of such clock is
smaller than its sampling rate. That way we can save some of the
precision of the fine clock.
To probe this point we have run three experiments on the Logitech C922.
On that experiment we run the camera at 33fps and we analyse the
difference in msec between a frame and its predecessor. If we display
the histogram of that value, a thinner histogram will mean a better
meassurement. The results for:
- original hw timestamp: https://ibb.co/D1HJJ4x
- pure software timestamp: https://ibb.co/QC9MgVK
- modified hw timestamp: https://ibb.co/8s9dBdk
This bug in the camera firmware has been confirmed by the vendor.
lsusb -v
Bus 001 Device 044: ID 046d:085c Logitech, Inc. C922 Pro Stream Webcam
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x046d Logitech, Inc.
idProduct 0x085c C922 Pro Stream Webcam
bcdDevice 0.16
iManufacturer 0
iProduct 2 C922 Pro Stream Webcam
iSerial 1 80B912DF
bNumConfigurations 1
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20240323-resend-hwtimestamp-v10-3-b08e590d97c7@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Some SunplusIT cameras took a borderline interpretation of the UVC 1.5
standard, and fill the PTS and SCR fields with invalid data if the
package does not contain data.
"STC must be captured when the first video data of a video frame is put
on the USB bus."
Some SunplusIT devices send, e.g.,
buffer: 0xa7755c00 len 000012 header:0x8c stc 00000000 sof 0000 pts 00000000
buffer: 0xa7755c00 len 000012 header:0x8c stc 00000000 sof 0000 pts 00000000
buffer: 0xa7755c00 len 000668 header:0x8c stc 73779dba sof 070c pts 7376d37a
While the UVC specification meant that the first two packets shouldn't
have had the SCR bit set in the header.
This borderline/buggy interpretation has been implemented in a variety
of devices, from directly SunplusIT and from other OEMs that rebrand
SunplusIT products. So quirking based on VID:PID will be problematic.
All the affected modules have the following extension unit:
VideoControl Interface Descriptor:
guidExtensionCode {82066163-7050-ab49-b8cc-b3855e8d221d}
But the vendor plans to use that GUID in the future and fix the bug,
this means that we should use heuristic to figure out the broken
packets.
This patch takes care of this.
lsusb of one of the affected cameras:
Bus 001 Device 003: ID 1bcf:2a01 Sunplus Innovation Technology Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2 ?
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1bcf Sunplus Innovation Technology Inc.
idProduct 0x2a01
bcdDevice 0.02
iManufacturer 1 SunplusIT Inc
iProduct 2 HanChen Wise Camera
iSerial 3 01.00.00
bNumConfigurations 1
Tested-by: HungNien Chen <hn.chen@sunplusit.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20240323-resend-hwtimestamp-v10-2-b08e590d97c7@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The tail of the list lives at the position before the head. This is
mathematically noted as:
```
(head-1) mod size.
```
Unfortunately C, does not have a modulus operator, but a remainder
operator (%).
The reminder operation has a different result than the modulus if
(head -1) is a negative number and size is not a power of two.
Adding size to (head-1) allows the code to run with any value of size.
This does not change the current behaviour of the driver, as the size is
always a power of two, but avoid tedious debugging if we ever change its
size.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240323-resend-hwtimestamp-v10-1-b08e590d97c7@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Avoid using the iterators after the list_for_each() constructs.
This patch should be a NOP, but makes cocci, happier:
drivers/media/usb/uvc/uvc_ctrl.c:1861:44-50: ERROR: invalid reference to the index variable of the iterator on line 1850
drivers/media/usb/uvc/uvc_ctrl.c:2195:17-23: ERROR: invalid reference to the index variable of the iterator on line 2179
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When the device suspends, it keeps power-cycling.
The user notices it because the LED constanct oscillate between
blue (ready) and no LED (off).
<6>[95202.128542] usb 3-3-port4: attempt power cycle
<6>[95206.070120] usb 3-3.4: new high-speed USB device number 49 using xhci_hcd
<6>[95206.212027] usb 3-3.4: New USB device found, idVendor=2e1a, idProduct=4c01, bcdDevice= 2.00
<6>[95206.212044] usb 3-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=<Serial: 1>
<6>[95206.212050] usb 3-3.4: Product: Insta360 Link
<6>[95206.212075] usb 3-3.4: Manufacturer: Amba
<7>[95206.214862] usb 3-3.4: GPIO lookup for consumer privacy
<7>[95206.214866] usb 3-3.4: using lookup tables for GPIO lookup
<7>[95206.214869] usb 3-3.4: No GPIO consumer privacy found
<6>[95206.214871] usb 3-3.4: Found UVC 1.10 device Insta360 Link (2e1a:4c01)
<3>[95206.217113] usb 3-3.4: Failed to query (GET_INFO) UVC control 14 on unit 1: -32 (exp. 1).
<3>[95206.217733] usb 3-3.4: Failed to query (GET_INFO) UVC control 16 on unit 1: -32 (exp. 1).
<4>[95206.223544] usb 3-3.4: Warning! Unlikely big volume range (=32767), cval->res is probably wrong.
<4>[95206.223554] usb 3-3.4: [9] FU [Mic Capture Volume] ch = 1, val = -32768/-1/1
<6>[95210.698990] usb 3-3.4: USB disconnect, device number 49
<6>[95211.963090] usb 3-3.4: new high-speed USB device number 50 using xhci_hcd
<6>[95212.657061] usb 3-3.4: new full-speed USB device number 51 using xhci_hcd
<3>[95212.783119] usb 3-3.4: device descriptor read/64, error -32
<3>[95213.015076] usb 3-3.4: device descriptor read/64, error -32
<6>[95213.120358] usb 3-3-port4: attempt power cycle
Bus 001 Device 009: ID 2e1a:4c01 Amba Insta360 Link
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x2e1a
idProduct 0x4c01
bcdDevice 2.00
iManufacturer 1 Amba
iProduct 2 Insta360 Link
iSerial 0
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20221101-instal-v1-0-d13d1331c4b5@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequency control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 3277:009e Shine-Optics Integrated Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x3277
idProduct 0x009e
bcdDevice 0.01
iManufacturer 3 Shine-Optics
iProduct 1 Integrated Camera
iSerial 2 0001
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240108-shine-v2-1-ddff959dab89@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Logitech Rally Bar devices, despite behaving as UVC cameras, have a
different power management system that the other cameras from Logitech.
USB_QUIRK_RESET_RESUME is applied to all the UVC cameras from Logitech
at the usb core. Unfortunately, USB_QUIRK_RESET_RESUME causes undesired
USB disconnects in the Rally Bar that make them completely unusable.
There is an open discussion about if we should fix this in the core or
add a quirk in the UVC driver. In order to enable this hardware, let's
land this patch first, and we can revert it later if there is a
different conclusion.
Fixes: e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Devinder Khroad <dkhroad@logitech.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20240404-rallybar-v6-1-6d67bb6b69af@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequency control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 2b7e:b752 SunplusIT Inc HD Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x2b7e
idProduct 0xb752
bcdDevice 0.04
iManufacturer 1 SunplusIT Inc
iProduct 2 HD Camera
iSerial 3 01.00.00
bNumConfigurations 1
Cc: Yunke Cao <yunkec@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When selecting an alternate setting, the driver loops over all available
alternate settings to find the one with the lowest bandwidth high enough
for the selected format and resolution. While all alternate settings
should have different packet sizes, some buggy devices report multiple
alternate settings with the same size. The driver happens to pick the
last one in this case.
In theory this should work fine, but in real life we have device bugs.
The Ali Corp. Newmine Camera (0402:8841) exposes four alternate
settings with the same packet size. The first three seem to work fine,
while selecting the last one results in lots of transmission errors.
Switch to using the first best alternate setting when multiple are
present. This should be safe (last famous words), as sniffing USB
traffic with the faulty device shows that Windows 10 picks the first
alternate setting, and devices are typically tested on Windows.
Closes: https://lore.kernel.org/linux-media/Nh6D0WI--3-9@tutanota.com/
Reported-by: Karel Janda <karel1@tutanota.com>
Suggested-by: Karel Janda <karel1@tutanota.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The device does not implement the control properly.
Fixes v4l2-compliance error:
info: checking control 'Power Line Frequency' (0x00980918)
fail: v4l2-test-controls.cpp(552): could not set valid menu item 3
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the index provided by the user is bigger than the mask size, we might do
an out of bound read.
CC: stable@kernel.org
Fixes: 40140eda66 ("media: uvcvideo: Implement mask for V4L2_CTRL_TYPE_MENU")
Reported-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When commit 716c330433 ("media: uvcvideo: Use standard names for
menus") reworked the handling of menu controls, it inadvertently
replaced a GENMASK(n - 1, 0) with a BIT_MASK(n). The latter isn't
equivalent to the former, which broke adding XU mappings from userspace.
Fix it.
Link: https://lore.kernel.org/linux-media/468a36ec-c3ac-cb47-e12f-5906239ae3cd@spahan.ch/
Cc: stable@vger.kernel.org
Reported-by: Poncho <poncho@spahan.ch>
Fixes: 716c330433 ("media: uvcvideo: Use standard names for menus")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no need to modify the content of UVC descriptor buffers during
parsing. Make all the corresponding pointers const to avoid unintended
modifications.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The formats, frames and intervals stored in the uvc_streaming structure
are not meant to change after being parsed at probe time. Make them
const to prevent unintended modifications, and adapt the probe code
accordingly to use non-const pointers during parsing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The intervals pointer is incremented for each interval when parsing the
format descriptor. This doesn't cause any issue as such, but gets in the
way of constifying some pointers. Modify the parsing code to index the
intervals pointer as an array and increment it in one go at end of
parsing.
Careful readers will notice that the maxIntervalIndex variable is set to
1 instead of n - 2 when bFrameIntervalType has a zero value. This is
functionally equivalent, as n is equal to 3 in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Format descriptor parsing has grown over time and now mixes parsing of
frame intervals with various quirk handling. Reorganize it to make the
code easier to follow, by parsing frame intervals first, and then
applying fixes and quirks. No functional change is intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel has a nice clamp() macro, use it to replace a manual
implementation based on min() and max(). No functional change is
intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvc_format 'frame' field points to an array of frames. Rename it to
'frames' to make this clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvc_streaming 'format' field points to an array of formats. Rename
it to 'formats' to make this clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Intel RealSense UVC Depth cameras produce metadata in a
vendor-specific format that is already supported by the uvcvideo driver.
Enable handling of this metadata for 7 additional RealSense devices.
Co-developed-by: Yu MENG <yu1.meng@intel.com>
Co-developed-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This reverts commit 5dd0eab84a.
Revert this patch as it has been merged twice. The earlier merged commit
is 81e78a6fc3 ("media: uvcvideo: Limit power line control for Acer
EasyCamera").
Reported-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the uvcvideo driver encounters a format descriptor with an unknown
format GUID, it creates a corresponding struct uvc_format instance with
the fcc field set to 0. Since commit 50459f103e ("media: uvcvideo:
Remove format descriptions"), the driver relies on the V4L2 core to
provide the format description string, which the V4L2 core can't do
without a valid 4CC. This triggers a WARN_ON.
As a format with a zero 4CC can't be selected, it is unusable for
applications. Ignore the format completely without creating a uvc_format
instance, which fixes the warning.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217252
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2180107
Fixes: 50459f103e ("media: uvcvideo: Remove format descriptions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since the uvc_fmts array can not be modified we declare it const and
change every user of the uvc_format_by_guid function aswell.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-5-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The media driver USB_VIDEO_CLASS and USB_F_UVC are using the same
function uvc_format_by_guid. Since the function is inline, every user
will get a copy of the used uvc_fmts array and the function. This patch
moves the code to an own compile unit and add this dependency as
UVC_COMMON to both users.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-4-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the headerfile is only used in usb devices it is better
placed with the other usb files.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memcpy() in uvc_video_decode_meta() intentionally copies across the
length and flags members and into the trailing buf flexible array.
Split the copy so that the compiler can better reason about (the lack
of) buffer overflows here. Avoid the run-time false positive warning:
memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1)
Additionally fix a typo in the documentation for struct uvc_meta_buf.
Reported-by: ionut_n2001@yahoo.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
usb_kill_urb warranties that all the handlers are finished when it
returns, but does not protect against threads that might be handling
asynchronously the urb.
For UVC, the function uvc_ctrl_status_event_async() takes care of
control changes asynchronously.
If the code is executed in the following order:
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_ctrl_status_event_work()
uvc_status_start() -> FAIL
Then uvc_status_start will keep failing and this error will be shown:
<4>[ 5.540139] URB 0000000000000000 submitted while active
drivers/usb/core/urb.c:378 usb_submit_urb+0x4c3/0x528
Let's improve the current situation, by not re-submiting the urb if
we are stopping the status event. Also process the queued work
(if any) during stop.
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_status_start()
uvc_ctrl_status_event_work() -> FAIL
Hopefully, with the usb layer protection this should be enough to cover
all the cases.
Cc: stable@vger.kernel.org
Fixes: e5225c820c ("media: uvcvideo: Send a control event when a Control Change interrupt arrives")
Reviewed-by: Yunke Cao <yunkec@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of duplicating the menu info, use the one from the core.
Also, do not use extra memory for 1:1 mappings.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequenyc control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 30c9:0093 Lenovo Integrated Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x30c9
idProduct 0x0093
bcdDevice 0.07
iManufacturer 3 Lenovo
iProduct 1 Integrated Camera
iSerial 2 8SSC21J75356V1SR2830069
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move the control mapping to uvc_ctrl.c. This way we do not have
references to UVC controls or V4L2 controls in uvc_driver.c.
This also fixes a bug introduced in commit 382075604a ("media:
uvcvideo: Limit power line control for Quanta UVC Webcam"). The
offending commit caused the power line control menu entries to have
incorrect indices compared to the V4L2_CID_POWER_LINE_FREQUENCY_*
enumeration. Now that the limited mapping reuses the correct menu_info
array, the indices correctly map to the V4L2 control specification.
Fixes: 382075604a ("media: uvcvideo: Limit power line control for Quanta UVC Webcam")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Convert the array of structs into an array of pointers, that way the
mappings can be reused.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Replace the count with a mask field that lets us choose not only the max
value, but also the minimum value and what values are valid in between.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make an explicit reference to UVC 1.5, explaining how the algorithm
supports the different behaviour of UVC 1.1 and 1.5.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: HungNien Chen <hn.chen@sunplusit.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Simplify the exit code with a common error tag freeing all the memory.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Minimum and step values for V4L2_CTRL_TYPE_BITMASK controls should be 0.
There is no need to query the camera firmware about this and maybe get
invalid results.
Also value should be masked to the max value advertised by the
hardware.
Finally, handle UVC 1.5 mask controls that use MAX instead of RES to
describe the valid bits.
Fixes v4l2-compliane:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(97): minimum must be 0 for a bitmask control
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
If the returned size of the query does not match the expected size or it
is zero, return -EPIPE instead of 0 or a positive value.
This will avoid confusing the caller (and ultimately userspace) that
doesn't expect a positive or zero value.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Error 2 is defined by UVC as:
Wrong State: The device is in a state that disallows the specific
request. The device will remain in this state until a specific action
from the host or the user is completed.
This is documented as happening when attempting to set the value of a
manual control when the device is in auto mode. While V4L2 allows this,
the closest error code defined by VIDIOC_S_CTRL is EACCES:
EACCES: Attempt to set a read-only control or to get a write-only
control. Or if there is an attempt to set an inactive control and the
driver is not capable of caching the new value until the control is
active again.
Replace EILSEQ with EACCES.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Standard use of the driver may result in error messages on the kernel
log. This can hide other more important messages, and alert
unnecessarily the user. Let's keep dev_err() for the important
occasions.
If __uvc_query_ctrl() failed with a non -EPIPE error, then report that
with dev_err. If an error code is obtained, then report that with
dev_dbg.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Check for inactive controls in uvc_ctrl_is_accessible().
Use the new value for the master_id controls if present, otherwise
use the existing value to determine if it is OK to set the control.
Doing this here avoids attempting to set an inactive control, which
will return an error from the USB device, which returns an invalid
errorcode.
This fixes:
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
test VIDIOC_G/S_CTRL: OK
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(816): s_ext_ctrls returned EIO
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
Tested with:
v4l2-ctl -c auto_exposure=1
OK
v4l2-ctl -c exposure_time_absolute=251
OK
v4l2-ctl -c auto_exposure=3
OK
v4l2-ctl -c exposure_time_absolute=251
VIDIOC_S_EXT_CTRLS: failed: Input/output error
exposure_time_absolute: Input/output error
ERROR
v4l2-ctl -c auto_exposure=3,exposure_time_absolute=251,auto_exposure=1
v4l2-ctl -C auto_exposure,exposure_time_absolute
auto_exposure: 1
exposure_time_absolute: 251
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When parsing UVC descriptors to instantiate entities, the driver calls
usb_string() to retrieve the entity name from the device, and falls back
to a default name if the string can't be retrieved. This code pattern
occurs multiple times. Factor it out to a separate helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Elgato Cam Link 4k can be in a stalled state if the resolution of
the external source has changed while the firmware initializes.
Once in this state, the device is useless until it receives a
USB reset. It has even been observed that the stalled state will
continue even after unplugging the device.
lsusb -v
Bus 002 Device 002: ID 0fd9:0066 Elgato Systems GmbH Cam Link 4K
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 9
idVendor 0x0fd9 Elgato Systems GmbH
idProduct 0x0066
bcdDevice 0.00
iManufacturer 1 Elgato
iProduct 2 Cam Link 4K
iSerial 4 0005AC52FE000
bNumConfigurations 1
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make the code more resilient, by replacing the castings with proper
structure definitions and using offsetof() instead of open coding the
location of the data.
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes 'do not use assignment in if condition' errors issued by
scripts/checkpatch.pl on drivers/media/usb/uvc/uvc_driver.c
Signed-off-by: Pedro Guilherme Siqueira Moreira <pedro.guilherme@espectro.eng.br>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes 'Missing a blank line after declarations' warning issued by
scripts/checkpatch.pl on drivers/media/usb/uvc/uvc_driver.c
Signed-off-by: Pedro Guilherme Siqueira Moreira <pedro.guilherme@espectro.eng.br>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On a Webcam from Quanta, we see the following error.
usb 3-5: New USB device found, idVendor=0408, idProduct=30d2, bcdDevice= 0.03
usb 3-5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 3-5: Product: USB2.0 HD UVC WebCam
usb 3-5: Manufacturer: Quanta
usb 3-5: SerialNumber: 0x0001
...
uvcvideo: Found UVC 1.10 device USB2.0 HD UVC WebCam (0408:30d2)
uvcvideo: Failed to initialize entity for entity 5
uvcvideo: Failed to register entities (-22).
The Webcam reports an entity of type UVC_VC_EXTENSION_UNIT. It reports a
string index of '7' associated with that entity. The attempt to read that
string from the camera fails with error -32 (-EPIPE). usb_string() returns
that error, but it is ignored. As result, the entity name is empty. This
later causes v4l2_device_register_subdev() to return -EINVAL, and no
entities are registered as result.
While this appears to be a firmware problem with the camera, the kernel
should still handle the situation gracefully. To do that, check the return
value from usb_string(). If it reports an error, assign the entity's
default name.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Examine the stream headers to figure out if the device has a button and
can be used as an input.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
If the source entity does not contain any pads, do not create a link.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The V4L2 core overwrites format descriptions in v4l_fill_fmtdesc(),
there's no need to manually set the descriptions in the driver. This
prepares for removal of the format descriptions from the uvc_fmts table.
Unlike V4L2, UVC makes a distinction between the SD-DV, SDL-DV and HD-DV
formats. It also indicates whether the DV format uses 50Hz or 60Hz. This
information is parsed by the driver to construct a format name string
that is printed in a debug message, but serves no other purpose as V4L2
has a single V4L2_PIX_FMT_DV pixel format that covers all those cases.
As the information is available in the UVC descriptors, and thus
accessible to users with lsusb if they really care, don't log it in a
debug message and drop the format name string to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER.
Reviewed-by: Sean Young <sean@mess.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices supported
and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before,
and some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new
chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices
better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different
USB drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BN9g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yljdgCdH4Fev4Nvf2Nokfv0q0krcRB3YpUAn1aZfpb/
EbgxsxhPnTJg+mmXyLms
=IxUy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
-----BEGIN PGP SIGNATURE-----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=MHQ/
-----END PGP SIGNATURE-----
Merge tag 'media/v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New driver for Mediatek MDP V3
- New driver for NXP i.MX DW100 dewarper
- Zoran driver got promoted from staging
- Hantro and related drivers got promoted from staging
- Several VB1 drivers got moved to staging/deprecated (cpia2, fsl-viu,
meye, saa7146, av7110, stkwebcam, tm6000, vpfe_capture, davinci,
zr364xx)
- Usual set of driver fixes, improvements and cleanups
* tag 'media/v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (107 commits)
media: destage Hantro VPU driver
media: platform: mtk-mdp3: add MediaTek MDP3 driver
media: dt-binding: mediatek: add bindings for MediaTek CCORR and WDMA
media: dt-binding: mediatek: add bindings for MediaTek MDP3 components
media: xilinx: vipp: Fix refcount leak in xvip_graph_dma_init
media: xilinx: video: Add 1X12 greyscale format
media: xilinx: csi2rxss: Add 1X12 greyscale format
media: staging: media: imx: imx7-media-csi: Increase video mem limit
media: uvcvideo: Limit power line control for Sonix Technology
media: uvcvideo: Use entity get_cur in uvc_ctrl_set
media: uvcvideo: Fix typo 'the the' in comment
media: uvcvideo: Use indexed loops in uvc_ctrl_init_ctrl()
media: uvcvideo: Fix memory leak in uvc_gpio_parse
media: renesas: vsp1: Add support for RZ/G2L VSPD
media: renesas: vsp1: Add VSP1_HAS_NON_ZERO_LBA feature bit
media: renesas: vsp1: Add support for VSP software version
media: renesas: vsp1: Add support to deassert/assert reset line
media: dt-bindings: media: renesas,vsp1: Document RZ/G2L VSPD bindings
media: meson: vdec: add missing clk_disable_unprepare on error in vdec_hevc_start()
media: amphion: fix a bug that vpu core may not resume after suspend
...
The uvc_format_desc, GUID defines and the uvc_format_by_guid helper is
also useful for the uvc gadget stack. This patch moves them to a common
header.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions uvc_simplify_fraction and uvc_fraction_to_interval are
generic helpers which are also useful for other v4l2 drivers. This patch
moves them to v4l2-common.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Quanta 0408:4034 camera implements UVC 1.5, and thus sets
bInterfaceProtocol to UVC_PC_PROTOCOL_15. Commit 95f03d9734 ("media:
uvcvideo: Limit power line control for Quanta cameras") added a quirk
for the device that incorrectly specified the UVC 1.0 protocol,
rendering the quirk inoperative. Fix it.
Link: https://lore.kernel.org/linux-media/20220822131754.102393-1-ribalda@chromium.org
Fixes: 95f03d9734 ("media: uvcvideo: Limit power line control for Quanta cameras")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Entity controls should get_cur using an entity-defined function
instead of via a query. Fix this in uvc_ctrl_set.
Fixes: 65900c581d ("media: uvcvideo: Allow entity-defined get_info and get_cur")
Signed-off-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As shown by the bug introduced in commit 86f7ef7731 ("media: uvcvideo:
Add support for per-device control mapping overrides"), the loop style
used by uvc_ctrl_init_ctrl() is error-prone. Rewrite the loops to use
indices instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Previously the unit buffer was allocated before checking the IRQ for
privacy GPIO. In case of error, the unit buffer was leaked.
Allocate the unit buffer after the IRQ to avoid it.
Addresses-Coverity-ID: 1474639 ("Resource leak")
Fixes: 2886477ff9 ("media: uvcvideo: Implement UVC_EXT_GPIO_UNIT")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The handling of per-device mappings introduced in commit 86f7ef7731
("media: uvcvideo: Add support for per-device control mapping
overrides") overwrote the mapping variable after it was initialized and
before it was used, leading to usage of an invalid pointer for devices
with per-device mappings. Fix it.
Fixes: 86f7ef7731 ("media: uvcvideo: Add support for per-device control mapping overrides")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The goto statement in uvc_v4l2_try_format can simply be replaced by an
direct return. There is no further user of the label, so remove it.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Two more cameras do not implement the power line control correctly. Add
a corresponding control mapping override.
Bus 001 Device 003: ID 0408:4034 Quanta Computer, Inc. ACER HD User Facing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x0408 Quanta Computer, Inc.
idProduct 0x4034
bcdDevice 0.01
iManufacturer 1 Quanta
iProduct 2 ACER HD User Facing
iSerial 3 01.00.00
bNumConfigurations 1
Bus 001 Device 003: ID 0408:4030 Quanta Computer, Inc. HD User Facing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x0408 Quanta Computer, Inc.
idProduct 0x4030
bcdDevice 0.02
iManufacturer 1 Quanta
iProduct 2 HD User Facing
iSerial 3 01.00.00
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some devices do not implement all their controls in a way that complies
with the UVC specification. This is for instance the case for several
devices that do not support the disabled mode for the power line
frequency control. Add a mechanism to allow per-device control mapping
overrides to avoid errors when accessing non-compliant controls.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
UVC 1.5 class defines 4 values for this control on:
4.2.2.3.6 Power Line Frequency Control
Add the missing value when the UVC version is 1.5.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The link to the web page that explains continued fractions is broken.
Replace it with a link to the corresponding Wikipedia page.
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvcvideo driver historically uses the
/* Comment
* style
*/
for multi-line block comments, which is frowned upon. Patches for the
driver are required to use the more standard
/*
* Comment
* style
*/
style. This result in inconsistencies. Fix it by converting all
remaining instances of the old style.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch aims to add UVC_GUID_FORMAT_H265
High Efficiency Video Coding (HEVC), also known as H.265 and MPEG-H Part 2.
They describe the same video encoding method.
So for handling their behavior is the same.
However, when external camera device describes this encoding method,
some use hevc, some use h265.
There is no uniform specification to describe this encoding method.
So if an external camera device use h265 to describe this encoding method,
driver will not recognize it.
Therefore, this patch is to enable driver to read HEVC/H265
and convert it to V4L2_PIX_FMT_HEVC.
Signed-off-by: James_Lin <Ping-lei.Lin@mediatek.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace manual decoding of psize in uvc_parse_streaming(), with the code
from uvc_endpoint_max_bpi(). It also handles usb3 devices.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The case USB_SPEED_WIRELESS and the default one were doing the same.
Also, make always use of usb_endpoint_maxp_mult, as it should have a
sane value, even for LOW speed and WIRELESS.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move all the life cycle of the name to add_mapping. This simplifies
the error handling inside uvc_ioctl_ctrl_map and solves a memory leak
when kemmdup fails.
Also make sure that for custom controls, the user provides a valid name.
Fixes: 07adedb5c606 ("media: uvcvideo: Use control names from framework")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
probe->dwMaxPayloadTransferSize is a 32bit value, but bandwidth is 16bit. This
may lead to a bit overflow.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The list iterator will point to a bogus position containing HEAD if
the list is empty or the element is not found in list. This case
should be checked before any use of the iterator, otherwise it will
lead to a invalid memory access. The missing check here is before
"pin = iterm->id;", just add check here to fix the security bug.
In addition, the list iterator value will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the element is not found in list, considering
the (mis)use here: "if (iterm == NULL".
Use a new value 'it' as the list iterator, while use the old value
'iterm' as a dedicated pointer to point to the found element, which
1. can fix this bug, due to 'iterm' is NULL only if it's not found.
2. do not need to change all the uses of 'iterm' after the loop.
3. can also limit the scope of the list iterator 'it' *only inside*
the traversal loop by simply declaring 'it' inside the loop in the
future, as usage of the iterator outside of the list_for_each_entry
is considered harmful. https://lkml.org/lkml/2022/2/17/1032
Fixes: d5e90b7a6c ("[media] uvcvideo: Move to video_ioctl2")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As discussed with other developers, the linux-uvc-devel mailing list is
not very useful anymore, and it's better to send people to the general
linux-media mailing list.
Replace/remove the old mailing list address in uvcvideo.rst and
MAINTAINERS.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media Kconfig has two entries associated to V4L API:
VIDEO_DEV and VIDEO_V4L2.
On Kernel 2.6.x, there were two V4L APIs, each one with its own flag.
VIDEO_DEV were meant to:
1) enable Video4Linux and make its Kconfig options to appear;
2) it makes the Kernel build the V4L core.
while VIDEO_V4L2 where used to distinguish between drivers that
implement the newer API and drivers that implemented the former one.
With time, such meaning changed, specially after the removal of
all V4L version 1 drivers.
At the current implementation, VIDEO_DEV only does (1): it enables
the media options related to V4L, that now has:
menu "Video4Linux options"
visible if VIDEO_DEV
source "drivers/media/v4l2-core/Kconfig"
endmenu
but it doesn't affect anymore the V4L core drivers.
The rationale is that the V4L2 core has a "soft" dependency
at the I2C bus, and now requires to select a number of other
Kconfig options:
config VIDEO_V4L2
tristate
depends on (I2C || I2C=n) && VIDEO_DEV
select RATIONAL
select VIDEOBUF2_V4L2 if VIDEOBUF2_CORE
default (I2C || I2C=n) && VIDEO_DEV
In the past, merging them would be tricky, but it seems that it is now
possible to merge those symbols, in order to simplify V4L dependencies.
Let's keep VIDEO_DEV, as this one is used on some make *defconfig
configurations.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for meson-vdec & meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds the requisite device id to support detection of the Apple FaceTime
HD webcam exposed over the T2 BCE VHCI interface.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Paul Pawlowski <paul@mrarm.io>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A lot of userspace depends on a descriptive name for vdev. Without this
patch, users have a hard time figuring out which camera shall they use
for their video conferencing.
This reverts commit e3f60e7e1a.
Link: https://lore.kernel.org/linux-media/20211207003840.1212374-2-ribalda@chromium.org
Cc: <stable@vger.kernel.org>
Fixes: e3f60e7e1a ("media: uvcvideo: Set unique vdev name based in type")
Reported-by: Nicolas Dufresne <nicolas@ndufresne.ca>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the memory where ctrl_found is placed has the value of uvc_ctrl and
__uvc_find_control does not find the control we will return an invalid
index.
Fixes: 6350d6a4ed ("media: uvcvideo: Set error_idx during ctrl_commit errors")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If mappings points to an invalid memory, we will be invalid accessing
it. Solve it by initializing the value of the variable mapping and by
changing the order in the conditional statement (to avoid accessing
mapping->id if not needed).
Fix:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN NOPTI
Fixes: 6350d6a4ed ("media: uvcvideo: Set error_idx during ctrl_commit errors")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Never return V4L2_COLORSPACE_DEFAULT. From the standard:
"""
In the absence of this descriptor, or in the case of
“Unspecified” values within the descriptor, color matching
defaults will be assumed. The color matching defaults are
compliant with sRGB since the BT.709 transfer function and
the sRGB transfer function are very similar.
"""
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Tested-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the missing bulk-endpoint max-packet sanity check to
uvc_video_start_transfer() to avoid division by zero in
uvc_alloc_urb_buffers() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Cc: stable@vger.kernel.org # 2.6.26
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently when the allocation of map->name fails the error exit path
does not kfree the previously allocated object map. Fix this by
setting ret to -ENOMEM and taking the free_map exit error path to
ensure map is kfree'd.
Addresses-Coverity: ("Resource leak")
Fixes: 70fa906d6f ("media: uvcvideo: Use control names from framework")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't report the restored controls with dev_info, use dev_dbg instead.
This prevents a lot of noise in the kernel log.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If we have an error setting a control, return the affected control in
the error_idx field.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We can figure out if reading/writing a set of controls can fail without
accessing them by checking their flags.
This way we can honor the API closer:
If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(765): g_ext_ctrls(0) invalid error_idx 0
fail: v4l2-test-controls.cpp(645): invalid error index write only control
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The framework already contains a map of IDs to names, lets use it when
possible.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans has discovered that in his test device, for the H264 format
bytesused goes up to about 570, for YUYV it will actually go up
to a bit over 5000 bytes, and for MJPG up to about 2706 bytes.
We should also, according to V4L2_META_FMT_UVC docs, drop headers when
the buffer is full.
Credit-to: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
All the entities must have a unique name. We can have a descriptive and
unique name by appending the function and the entity->id.
This is even resilent to multi chain devices.
Fixes v4l2-compliance:
Media Controller ioctls:
fail: v4l2-test-media.cpp(205): v2_entity_names_set.find(key) != v2_entity_names_set.end()
test MEDIA_IOC_G_TOPOLOGY: FAIL
fail: v4l2-test-media.cpp(394): num_data_links != num_links
test MEDIA_IOC_ENUM_ENTITIES/LINKS: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the device name for the card name instead of vdev->name. That way
all the devices have a different name instead of the common vdev->name.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create all the class controls for the device defined controls.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(216): missing control class for class 00980000
fail: v4l2-test-controls.cpp(216): missing control tclass for class 009a0000
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Pass the chain instead of the device. We want to keep the reference to
the chain that controls belong to.
We need to delay the initialization of the controls after the chains
have been initialized.
This is a cleanup needed for the next patches.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If we do not implement these callbacks the framework will call the
ext_ctrl callbaks instead, which are a superset of this functions.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The framework already checks for us if V4L2_CTRL_WHICH_DEF_VAL is
written.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove including <linux/version.h> that don't need it.
V1->V2: Split the patch in two.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Elgato Cam Link 4K HDMI video capture card reports to support three
different pixel formats, where the first format depends on the connected
HDMI device.
```
$ v4l2-ctl -d /dev/video0 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
Type: Video Capture
[0]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[1]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[2]: 'YU12' (Planar YUV 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
```
Changing the pixel format to anything besides the first pixel format
does not work:
```
$ v4l2-ctl -d /dev/video0 --try-fmt-video pixelformat=YU12
Format Video Capture:
Width/Height : 3840/2160
Pixel Format : 'NV12' (Y/CbCr 4:2:0)
Field : None
Bytes per Line : 3840
Size Image : 12441600
Colorspace : sRGB
Transfer Function : Rec. 709
YCbCr/HSV Encoding: Rec. 709
Quantization : Default (maps to Limited Range)
Flags :
```
User space applications like VLC might show an error message on the
terminal in that case:
```
libv4l2: error set_fmt gave us a different result than try_fmt!
```
Depending on the error handling of the user space applications, they
might display a distorted video, because they use the wrong pixel format
for decoding the stream.
The Elgato Cam Link 4K responds to the USB video probe
VS_PROBE_CONTROL/VS_COMMIT_CONTROL with a malformed data structure: The
second byte contains bFormatIndex (instead of being the second byte of
bmHint). The first byte is always zero. The third byte is always 1.
The firmware bug was reported to Elgato on 2020-12-01 and it was
forwarded by the support team to the developers as feature request.
There is no firmware update available since then. The latest firmware
for Elgato Cam Link 4K as of 2021-03-23 has MCU 20.02.19 and FPGA 67.
Therefore correct the malformed data structure for this device. The
change was successfully tested with VLC, OBS, and Chromium using
different pixel formats (YUYV, NV12, YU12), resolutions (3840x2160,
1920x1080), and frame rates (29.970 and 59.940 fps).
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Drung <bdrung@posteo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- add a new dma_alloc_noncontiguous API (me, Ricardo Ribalda)
- fix a copyright noice (Hao Fang)
- add an unlikely annotation to dma_mapping_error (Heiner Kallweit)
- remove a pointless empty line (Wang Qing)
- add support for multi-pages map/unmap bencharking (Xiang Chen)
-----BEGIN PGP SIGNATURE-----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=DJoy
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add a new dma_alloc_noncontiguous API (me, Ricardo Ribalda)
- fix a copyright notice (Hao Fang)
- add an unlikely annotation to dma_mapping_error (Heiner Kallweit)
- remove a pointless empty line (Wang Qing)
- add support for multi-pages map/unmap bencharking (Xiang Chen)
* tag 'dma-mapping-5.13' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: add unlikely hint to error path in dma_mapping_error
dma-mapping: benchmark: Add support for multi-pages map/unmap
dma-mapping: benchmark: use the correct HiSilicon copyright
dma-mapping: remove a pointless empty line in dma_alloc_coherent
media: uvcvideo: Use dma_alloc_noncontiguous API
dma-iommu: implement ->alloc_noncontiguous
dma-iommu: refactor iommu_dma_alloc_remap
dma-mapping: add a dma_alloc_noncontiguous API
dma-mapping: refactor dma_{alloc,free}_pages
dma-mapping: add a dma_mmap_pages helper
Some devices reference an output terminal as the source of extension
units. This is incorrect, as output terminals only have an input pin,
and thus can't be connected to any entity in the forward direction. The
resulting topology would cause issues when registering the media
controller graph. To avoid this problem, connect the extension unit to
the source of the output terminal instead.
While at it, and while no device has been reported to be affected by
this issue, also handle forward scans where two output terminals would
be connected together, and skip the terminals found through such an
invalid connection.
Reported-and-tested-by: John Nealy <jnealy3@yahoo.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
An error message in the forward scan code incorrectly prints the ID of
the source entity instead of the XU entity being scanned. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of strncpy is discouraged, use strscpy instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
trace isn't a good name as it's not a trace mechanism, it is a
typical debug mechanism.
Rename uvc_trace/uvc_trace_cont macros to uvc_dbg/uvc_dbg_cont.
Rename uvc_trace_param to uvc_dbg_param
Rename UVC_TRACE_<FOO> defines to UVC_DBG_<FOO>
Use ## concatenation in uvc_dbg macros to avoid overly long and
repetitive UVC_DBG uses
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of calling prink() inside uvc_trace, use dev_printk(), which adds
context to the output.
Now that we are at it, regroup the strings so the messages can be easily
"grepable".
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove all the duplicated code around printk(KERN_CONT, with a new macro.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace all the uses of printk() and uvc_printk() with its
equivalent dev_ alias macros.
Modify uvc_warn_once() macro to use dev_info instead printk().
They are more standard across the kernel tree and provide
more context about the error.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a new control and mapping for Privacy controls connected to
UVC_GUID_EXT_GPIO_CONTROLLERs.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some devices can implement a physical switch to disable the input of the
camera on demand. Think of it like an elegant privacy sticker.
The system can read the status of the privacy switch via a GPIO.
It is important to know the status of the switch, e.g. to notify the
user when the camera will produce black frames and a videochat
application is used.
In some systems, the GPIO is connected to the main SoC instead of the
camera controller, with the connection reported by the system firmware
(ACPI or DT). In that case, the UVC device isn't aware of the GPIO. We
need to implement a virtual entity to handle the GPIO fully on the
driver side.
For example, for ACPI-based systems, the GPIO is reported in the USB
device object:
Scope (\_SB.PCI0.XHCI.RHUB.HS07)
{
/.../
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0064
}
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x01)
{
Package (0x02)
{
"privacy-gpio",
Package (0x04)
{
\_SB.PCI0.XHCI.RHUB.HS07,
Zero,
Zero,
One
}
}
}
})
}
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allows controls to get their properties and current value
from an entity-defined function instead of via a query to the USB
device.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split the functionality of void uvc_ctrl_status_event_work in two, so it
can be called by functions outside interrupt context and not part of an
URB.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Avoid an underflow while calculating the number of inputs for entities
with zero pads.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Increase the size of the id, to avoid collisions with entities
implemented by the driver that are not part of the UVC device.
Entities exposed by the UVC device use IDs 0-255, extra entities
implemented by the driver (such as the GPIO entity) use IDs 256 and
up.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of having multiple copies of the entity guid on the code, move
it to the entity structure.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Renkforce RF AC4K 300 Action Cam 4K reports invalid bFormatIndex and
bFrameIndex values when negotiating the video probe and commit controls.
The UVC descriptors report a single supported format and frame size,
with bFormatIndex and bFrameIndex both equal to 2, but the video probe
and commit controls report bFormatIndex and bFrameIndex set to 1.
The device otherwise operates correctly, but the driver rejects the
values and fails the format try operation. Fix it by ignoring the
invalid indices, and assuming that the format and frame requested by the
driver are accepted by the device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210767
Fixes: 8a652a17e3 ("media: uvcvideo: Ensure all probed info is returned to v4l2")
Reported-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Shenzhen Aoni Electronic Co.,Ltd 2K FHD camera reports a UVC 1.10
version, but implements UVC 1.0a as shown by the UVC probe control being
26 bytes long. Force the UVC version for that device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Doncho Minkov <donchominkov@gmail.com>
Tested-by: Doncho Minkov <donchominkov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Color Matching Descriptor has been present in USB cameras since
the original version of UVC, but it has never been fully exposed
in Linux.
This change informs V4L2 of all of the UVC colorspace parameters:
color primaries, transfer characteristics, and YCbCr encoding.
videodev2.h doesn't have values for all the possible UVC color settings,
so it is mapped as closely as possible.
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
bFrameIndex and bFormatIndex can be negotiated by the camera during
probing, resulting in the camera choosing a different format than
expected. v4l2 can already accommodate such changes, but the code was
not updating the proper fields.
Without such a change, v4l2 would potentially interpret the payload
incorrectly, causing corrupted output. This was happening on the
Elgato HD60 S+, which currently always renegotiates to format 1.
As an aside, the Elgato firmware is buggy and should not be renegotating,
but it is still a valid thing for the camera to do. Both macOS and Windows
will properly probe and read uncorrupted images from this camera.
With this change, both qv4l2 and chromium can now read uncorrupted video
from the Elgato HD60 S+.
[Add blank lines, remove periods at the of messages]
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UBSAN reports a shift-out-of-bounds warning in uvc_get_le_value(). The
report is correct, but the issue should be harmless as the computed
value isn't used when the shift is negative. This may however cause
incorrect behaviour if a negative shift could generate adverse side
effects (such as a trap on some architectures for instance).
Regardless of whether that may happen or not, silence the warning as a
full WARN backtrace isn't nice.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes the following coccinelle report:
drivers/media/usb/uvc/uvc_ctrl.c:1860:5-11:
ERROR: invalid reference to the index variable of the iterator on line 1854
by adding a boolean variable to check if the loop has found the
Found using - Coccinelle (http://coccinelle.lip6.fr)
[Replace cursor variable with bool found]
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is only 1 error exit in uvc_ctrl_add_info(), so using goto style
error handling is not necessary. Also the kfree(ctrl->uvc_data) on error
is not necessary, because the only error exit is for the kzalloc() of
ctrl->uvc_data failing.
Remove all the error handling cruft and simply do "return -ENOMEM" on
kzalloc() failure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
uvc_ctrl_add_info() calls uvc_ctrl_get_flags() which will override
the fixed-up flags set by uvc_ctrl_fixup_xu_info().
uvc_ctrl_init_xu_ctrl() already calls uvc_ctrl_get_flags() before
calling uvc_ctrl_add_info(), so the uvc_ctrl_get_flags() call in
uvc_ctrl_add_info() is not necessary for xu ctrls.
This commit moves the uvc_ctrl_get_flags() call for normal controls
from uvc_ctrl_add_info() to uvc_ctrl_init_ctrl(), so that we no longer
call uvc_ctrl_get_flags() twice for xu controls and so that we no longer
override the fixed-up flags set by uvc_ctrl_fixup_xu_info().
This fixes the xu motor controls not working properly on a Logitech
046d:08cc, and presumably also on the other Logitech models which have
a quirk for this in the uvc_ctrl_fixup_xu_info() function.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media controller core prints a warning when an entity is registered
without a function being set. This affects the uvcvideo driver, as the
warning was added without first addressing the issue in existing
drivers. The problem is harmless, but unnecessarily worries users. Fix
it by mapping UVC entity types to MC entity functions as accurately as
possible using the existing functions.
Fixes: b50bde4e47 ("[media] v4l2-subdev: use MEDIA_ENT_T_UNKNOWN for new subdevs")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add HEVC GUID and assotiate with HEVC pixel format so that frame
based format descriptors recognized by the UVC video driver.
Signed-off-by: Dmitry Buzdyk <dima.buzdyk@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The formula (2) is to convert from SOF to host clock,
it should be fix as
"TS = ((TS2 - TS1) * SOF + TS1 * SOF2 - TS2 * SOF1) / (SOF2 - SOF1)"
Signed-off-by: Jun Chen <jun.chen@vatics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This device does not function correctly in raw mode in kernel
versions validating buffer sizes in bulk mode. It erroneously
announces 16 bits per pixel instead of 12 for NV12 format, so it
needs this quirk to fix computed frame size and avoid legitimate
frames getting discarded.
[Move info and div variables to local scope]
Signed-off-by: Sergey Zakharchenko <szakharchenko@digital-loggers.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Way back in 2017, fuzzing the 4.14-rc2 USB stack with syzkaller kicked
up the following WARNING from the UVC chain scanning code:
| list_add double add: new=ffff880069084010, prev=ffff880069084010,
| next=ffff880067d22298.
| ------------[ cut here ]------------
| WARNING: CPU: 1 PID: 1846 at lib/list_debug.c:31 __list_add_valid+0xbd/0xf0
| Modules linked in:
| CPU: 1 PID: 1846 Comm: kworker/1:2 Not tainted
| 4.14.0-rc2-42613-g1488251d1a98 #238
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
| Workqueue: usb_hub_wq hub_event
| task: ffff88006b01ca40 task.stack: ffff880064358000
| RIP: 0010:__list_add_valid+0xbd/0xf0 lib/list_debug.c:29
| RSP: 0018:ffff88006435ddd0 EFLAGS: 00010286
| RAX: 0000000000000058 RBX: ffff880067d22298 RCX: 0000000000000000
| RDX: 0000000000000058 RSI: ffffffff85a58800 RDI: ffffed000c86bbac
| RBP: ffff88006435dde8 R08: 1ffff1000c86ba52 R09: 0000000000000000
| R10: 0000000000000002 R11: 0000000000000000 R12: ffff880069084010
| R13: ffff880067d22298 R14: ffff880069084010 R15: ffff880067d222a0
| FS: 0000000000000000(0000) GS:ffff88006c900000(0000) knlGS:0000000000000000
| CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
| CR2: 0000000020004ff2 CR3: 000000006b447000 CR4: 00000000000006e0
| Call Trace:
| __list_add ./include/linux/list.h:59
| list_add_tail+0x8c/0x1b0 ./include/linux/list.h:92
| uvc_scan_chain_forward.isra.8+0x373/0x416
| drivers/media/usb/uvc/uvc_driver.c:1471
| uvc_scan_chain drivers/media/usb/uvc/uvc_driver.c:1585
| uvc_scan_device drivers/media/usb/uvc/uvc_driver.c:1769
| uvc_probe+0x77f2/0x8f00 drivers/media/usb/uvc/uvc_driver.c:2104
Looking into the output from usbmon, the interesting part is the
following data packet:
ffff880069c63e00 30710169 C Ci:1:002:0 0 143 = 09028f00 01030080
00090403 00000e01 00000924 03000103 7c003328 010204db
If we drop the lead configuration and interface descriptors, we're left
with an output terminal descriptor describing a generic display:
/* Output terminal descriptor */
buf[0] 09
buf[1] 24
buf[2] 03 /* UVC_VC_OUTPUT_TERMINAL */
buf[3] 00 /* ID */
buf[4] 01 /* type == 0x0301 (UVC_OTT_DISPLAY) */
buf[5] 03
buf[6] 7c
buf[7] 00 /* source ID refers to self! */
buf[8] 33
The problem with this descriptor is that it is self-referential: the
source ID of 0 matches itself! This causes the 'struct uvc_entity'
representing the display to be added to its chain list twice during
'uvc_scan_chain()': once via 'uvc_scan_chain_entity()' when it is
processed directly from the 'dev->entities' list and then again
immediately afterwards when trying to follow the source ID in
'uvc_scan_chain_forward()'
Add a check before adding an entity to a chain list to ensure that the
entity is not already part of a chain.
Link: https://lore.kernel.org/linux-media/CAAeHK+z+Si69jUR+N-SjN9q4O+o5KFiNManqEa-PjUta7EOb7A@mail.gmail.com/
Cc: <stable@vger.kernel.org>
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd5+Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylA4wCbB3P206oHeHLBe9Eika3D8gM9/fMAn2oWlmpB
Xh7wr30FGC02zU/KBpJ1
=U5qC
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
It is likely that it should be UVC_METADATA_BUF_SIZE instead.
Fix it and use it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When parsing the UVC control descriptors fails, the error path tries to
cleanup a media device that hasn't been initialised, potentially
resulting in a crash. Fix this by initialising the media device before
the error handling path can be reached.
Fixes: 5a254d751e ("[media] uvcvideo: Register a v4l2_device")
Reported-by: syzbot+c86454eb3af9e8a4da20@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The priv field of struct v4l2_pix_format shouldn't be set by drivers,
it's set by the v4l2 core instead to V4L2_PIX_FMT_PRIV_MAGIC.
Drop this from the few media drivers that still do this.
Note that the gspca patch is slightly more involved since some of the
sub-gspca drivers use the priv field internally.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: fix clash in gspca between priv arg and priv variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We need to check whether this work we are canceling actually is
initialized.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+2e1ef9188251d9cc7944@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
uvcvideo creates a debugfs directory based on the device bus number and
device number. If a device contains more than one uvc function, the
creation of the second and following debugfs directories will fail and
print an info message like this:
"uvcvideo: Unable to create debugfs 3-2 directory."
This patch includes the uvc streaming interface number in the debugfs
directory name, to make sure it is unique. The directory name format is
changed from "<busnum>-<devnum>" to "<busnum>-<devnum>-<intfnum>"
Signed-off-by: Torleiv Sundre <torleiv@huddly.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
