ACV expects an enable_mask corresponding to the APPS RSC, fill it in.
Fixes: 46bdcac533 ("interconnect: qcom: Add SC7280 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-acv-v2-3-765ad70e539a@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
ACV expects an enable_mask corresponding to the APPS RSC, fill it in.
Fixes: 2d1f95ab9f ("interconnect: qcom: Add SC7180 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-acv-v2-2-765ad70e539a@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
ACV expects an enable_mask corresponding to the APPS RSC, fill it in.
Fixes: 1f51339f7d ("interconnect: qcom: Add QDU1000/QRU1000 interconnect driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-acv-v2-1-765ad70e539a@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
QCM2290 can support two memory configurations: single-channel, 32-bit
wide LPDDR3 @ up to 933MHz (bus clock) or dual-channel, 16-bit wide
LPDDR4X @ up to 1804 MHz. The interconnect driver in its current form
seems to gravitate towards the first one, however there are no LPDDR3-
equipped boards upstream and we still don't have a great way to discern
the DDR generations on the kernel side.
To make DDR scaling possible on the only currently-supported 2290
board, stick with the LPDDR4X config by default. The side effect on any
potential LPDDR3 board would be that the requested bus clock rate is
too high (but still capped to the firmware-configured FMAX).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230726-topic-icc_coeff-v4-7-c04b60caa467@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This single node has its own clock which seems to be responsible for
transactions between CPUSS (CPU + some stuff) and the GNOC. See [1]
for reference.
Define it and hook it up.
[1] 02f8c342b2%5E%21/#F0
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230726-topic-icc_coeff-v4-5-c04b60caa467@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
If this hardware couldn't get messier, some nodes are supposed to drive
their own bus clock.. Presumably to connect to some intermediate
interface between the node itself and the bus it's (supposed to be)
connected to.
Expand the node struct with the necessary data and hook up the
allocations & calculations.
Note that the node-specific AB/IB coefficients contribute (by design)
to both the node-level and the bus-level aggregation.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230726-topic-icc_coeff-v4-3-c04b60caa467@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Presumably due to the hardware being so complex, some nodes (or busses)
have different (usually higher) requirements for bandwidth than what
the usual calculations would suggest.
Looking at the available downstream files, it seems like AB values are
adjusted per-bus and IB values are adjusted per-node.
With that in mind, introduce percentage-based coefficient struct members
and use them in the calculations.
One thing to note is that the IB coefficient is inverse (100/ib_percent)
which feels a bit backwards, but it's necessary for precision..
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230726-topic-icc_coeff-v4-1-c04b60caa467@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
BCMs with an enable_mask expect to only have that specific value written
to them. The current implementation only works by miracle for BCMs with
enable mask == BIT(0), as the minimal vote we've been using so far just
so happens to be equal to that.
Use the correct value with keepalive voting.
Fixes: d8630f050d ("interconnect: qcom: Add support for mask-based BCMs")
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-icc_fix_1he-v2-2-0620af8ac133@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We don't need all the complex arithmetic for BCMs utilizing enable_mask,
as all we need to do is to determine whether there's any user (or
keepalive) asking for it to be on.
Separate the logic for such BCMs for a small speed boost.
Suggested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-icc_fix_1he-v2-1-0620af8ac133@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Enable sync_state on sm8450 so that the interconnect votes actually mean
anything and aren't just pinned to INT_MAX.
Fixes: fafc114a46 ("interconnect: qcom: Add SM8450 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230811-topic-8450_syncstate-v1-1-69ae5552a18b@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct icc_onecell_data.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Georgi Djakov <djakov@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230817204215.never.916-kees@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This series contains fixes necessary for icc to behave correctly
on QCM2290.
* icc-qcm2290
interconnect: qcom: qcm2290: Enable keep_alive on all buses
interconnect: qcom: qcm2290: Enable sync state
Link: https://lore.kernel.org/r/20230720-topic-qcm2290_icc-v2-0-a2ceb9d3e713@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmTZISMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGP+kH/RJWesO8dQ1b2jRh
v1dexbytGUykROpmHBnJKDznwsSBnhDlI9Tu62dumWKRrCzwZto8Hag1QC2jYrra
x7f3W087HdTSh3j5B92kGK/ZXgm4NwjVI078ujSv/e+qJMB3behpdL7uUkFUeeVV
OaDhlSL4ILlyVOYPX3sHMiPutmZcXxe8/25o4aylpBrzlClKen7OODRz6gIwyVOR
Nufgi/H5bkB4rDLOVI87HrxQMSpCtyGJtjTB78e/aRvIwYhJq16iuq+uBqOxQqgr
anlg1nJ3r6/LphiT9H63xNFwIJDxtL7I1V8CQ9Jyvf/O4MNGSaM7sHw2l8ujTxU9
hf4GYyY=
=loC2
-----END PGP SIGNATURE-----
Merge tag 'v6.5-rc6' into icc-next
The fixes that got merged into v6.5-rc6 are needed here.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Enable the generic .sync_state callback to ensure there are no
outstanding votes that would waste power.
Generally one would need a bunch of interface clocks to access the QoS
registers when trying to go over all possible nodes during sync_state,
but QCM2290 surprisingly does not seem to require any such handling.
Fixes: 1a14b1ac39 ("interconnect: qcom: Add QCM2290 driver support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230720-topic-qcm2290_icc-v2-2-a2ceb9d3e713@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
QCM2290 expects all buses to be up at all times when the CPU is
active. Enable keep_alive on all of them to achieve that.
Fixes: 1a14b1ac39 ("interconnect: qcom: Add QCM2290 driver support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230720-topic-qcm2290_icc-v2-1-a2ceb9d3e713@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
SM8250 (like SM8150 but unlike all other QUP-equipped SoCs) doesn't
provide a qup-core path. Adjust the bindings and drivers as necessary,
and then describe the icc paths in the device tree. This makes it possible
for interconnect sync_state succeed so long as you don't use UFS.
* icc-sm8250-qup
dt-bindings: interconnect: qcom,rpmh: Add SM8250 QUP virt
dt-bindings: interconnect: qcom,sm8250: Add QUP virt
interconnect: qcom: sm8250: Fix QUP0 nodes
Link: https://lore.kernel.org/r/20230703-topic-8250_qup_icc-v2-0-9ba0a9460be2@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The QUP0 BCM relates to some internal property of the QUPs, and should
be configured independently of the path to the QUP. In line with other
platforms expose QUP_CORE endpoints in order allow this configuration.
Fixes: 6df5b34949 ("interconnect: qcom: Add SM8250 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230703-topic-8250_qup_icc-v2-3-9ba0a9460be2@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Fix the following smatch error:
drivers/interconnect/qcom/icc-rpm.c:243 qcom_icc_rpm_set() error: uninitialized symbol 'ret'.
Fixes: 32846c4a8f ("interconnect: qcom: icc-rpm: Set bandwidth on both contexts")
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230717125534.2455745-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174638.4058268-1-robh@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Up until now, we've been aggregating the bandwidth values and only
dividing them by the bus width of the source node. This was completely
wrong, as different nodes on a given path may (and usually do) have
varying bus widths. That in turn, resulted in the calculated clock rates
being completely bogus - usually they ended up being much higher, as
NoC_A<->NoC_B links are very wide.
Since we're not using the aggregate bandwidth value for anything other
than clock rate calculations, remodel qcom_icc_bus_aggregate() to
calculate the per-context clock rate for a given provider, taking into
account the bus width of every individual node.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-22-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently, we're setting the aggregated-on-provider bandwidth on each
node, individually. That is of course incorrect and results in far too
high votes. Use the correct values to ensure we're not wasting power.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-21-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Up until now, for some reason we've only been setting bandwidth values
on the active-only context. That pretty much meant that RPM could lift
all votes when entering sleep mode. Or never sleep at all.
That in turn could potentially break things like USB wakeup, as the
connection between APSS and SNoC/PNoC would simply be dead.
Set the values appropriately.
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-20-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SMD RPM only provides two buckets, one each for the active-only and
active-sleep RPM contexts. Use the correct constant to allocate and
operate on them.
This will make the qcom,icc.h header no longer work with this driver,
mostly because.. it was never meant to! The commit that introduced
bucket support to SMD RPM was trying to shove a square into a round
hole and it did not work out very well. That said, there are no
active users of SMD RPM ICC + qcom,icc.h, so that doesn't hurt.
Fixes: dcbce7b0a7 ("interconnect: qcom: icc-rpm: Support multiple buckets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-19-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The sole purpose of bus clocks that were previously registered with
rpmcc was to convey the aggregated bandwidth to RPM. There's no good
reason to keep them outside the interconnect framework, as it only
adds to the plentiful complexity.
Add the required code to handle these clocks from within SMD RPM ICC.
RPM-owned bus clocks are no longer considered a thing, but sadly we
have to allow for the existence of HLOS-owned bus clocks, as some
(mostly older) SoCs (ab)use these for bus scaling (e.g. MSM8998 and
&mmcc AHB_CLK_SRC).
This in turn is trivially solved with a single *clk, which is filled
and used iff qp.bus_clk_desc is absent and we have a "bus" clock-names
entry in the DT node.
This change should(tm) be fully compatible with all sorts of old
Device Trees as far as the interconnect functionality goes (modulo
abusing bus clock handles or wrongly using the qcom,icc.h binding,
but that's a mistake in and of itself).
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-17-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-16-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-15-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-14-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-13-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-12-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assign the necessary definitions to migrate to the new bus clock
handling mechanism.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-11-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the definitions for RPM bus clocks that will be used by many
different platforms.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-10-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce qcom_icc_rpm_set_bus_rate() in preparation for handling RPM
clock resources within the interconnect framework. This lets us greatly
simplify all of the code handling, as setting the rate comes down to:
u32 rate_khz = max(clk.sleep_rate, clk.active_rate, clk_a.active_rate)
write_to_rpm(clock.description, rate_khz);
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-9-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
smd-rpm.h is not very useful as-is and both files are always included
anyway.. Combine them.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-8-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently the header does not provide all the required dependencies.
Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-7-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The downstream kernel employs the concept of "keeping the bus alive"
by voting for the minimum (XO/19.2MHz) rate at all times on certain
(well, most) buses. This is a very important thing to have, as if we
either have a lackluster/wrong DT that doesn't specify a (high enough)
vote on a certain bus, we may lose access to the entire bus altogether.
This is very apparent when we only start introducing interconnect
support on a given platform and haven't yet introduced voting on all
peripherals.
The same can happen if we only have a single driver casting a vote on
a certain bus and that driver exits/crashes/suspends.
The keepalive vote is limited to the ACTIVE bucket, as keeping a
permanent vote on the SLEEP one could prevent the platform from properly
entering low power mode states.
Introduce the very same concept, with a slight twist: the vendor
kernel checks whether the rate is zero before setting the minimum
vote, but that's rather silly, as in doing so we're at the mercy
of CCF. Instead, explicitly clamp the rates to always be >= 19.2 MHz
for providers with keep_alive=true.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230526-topic-smd_icc-v7-6-09c78c175546@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some BCMs aren't directly associated with the data path (i.e. ACV) and
therefore don't communicate using BW. Instead, they are simply
enabled/disabled with a simple bit mask. Add support for these.
Origin commit retrieved from:
2d1573e020
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
[narmstrong: removed copyright change from original commit]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230619-topic-sm8550-upstream-interconnect-mask-vote-v2-1-709474b151cc@linaro.org
Fixes: fafc114a46 ("interconnect: qcom: Add SM8450 interconnect provider driver")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This was not allocating enough bytes. There are two issue here.
First, there was a typo where it was taking the size of the pointer
instead of the size of the struct, "sizeof(qp->intf_clks)" vs
"sizeof(*qp->intf_clks)". Second, it's an array of "cd_num" clocks so
we need to allocate space for more than one element.
Fixes: 2e2113c8a6 ("interconnect: qcom: rpm: Handle interface clocks")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/e0fa275c-ae63-4342-9c9e-0ffaf6314da1@kili.mountain
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The interconnect driver is (or soon will be) vital to many other
devices, as it's not a given that the bootloader will set up enough
bandwidth for us or that the values we come into are reasonable.
Promote the driver to core_initcall to ensure the consumers (i.e.
most "meaningful" parts of the SoC) can probe without deferrals.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-8-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Commit dd42ec8ea5 ("interconnect: qcom: rpm: Use _optional func for provider clocks")
relaxed the requirements around probing bus clocks. This was a decent
solution for making sure MSM8996 would still boot with old DTs, but
now that there's a proper fix in place that both old and new DTs
will be happy about, revert back to the safer variant of the
function.
Fixes: dd42ec8ea5 ("interconnect: qcom: rpm: Use _optional func for provider clocks")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-7-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
For SMD RPM bus scaling to work, we need a pair of sleep-wake clocks.
The variable number of them we previously supported was only a hack
to keep the clocks required for QoS register access, but now that
these are separated, we can leave bus_clks to the actual bus clocks.
In cases where there is no actual bus scaling (such as A0NoC on MSM8996
and GNoC on SDM660 where the HLOS is only supposed to program the QoS
registers and the bus is either static or controlled remotely), allow
for no clock scaling with a boolean property.
Remove all the code related to allowing an arbitrary number of bus_clks,
replace the number by BUS_CLK_MAX (= 2) and guard the bus clock paths
to ensure they are not taken on non-scaling buses.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-6-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Some (but not all) providers (or their specific nodes) require
specific clocks to be turned on before they can be accessed. Failure
to ensure that results in a seemingly random system crash (which
would usually happen at boot with the interconnect driver built-in),
resulting in the platform not booting up properly.
Limit the number of bus_clocks to 2 (which is the maximum that SMD
RPM interconnect supports anyway) and handle non-scaling clocks
separately. Update MSM8996 and SDM660 drivers to make sure they do
not regress with this change.
This unfortunately has to be done in one patch to prevent either
compile errors or broken bisect.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230518195801.2556998-1-konrad.dybcio@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The QoS registers are (or according to Qualcomm folks, on most
platforms) persistent until a full chip reboot. Move the QoS-setting
functions to the probe function so that we don't needlessly do it over
and over again.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-4-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation for handling non-scaling clocks that we still have to
enable, rename num_clocks to more descriptive num_bus_clocks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-2-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Rename the "clocks" (and _names) fields of qcom_icc_desc to
"bus_clocks" in preparation for introducing handling of clocks that
need to be enabled but not voted on with aggregate frequency.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v8-1-ee696a2c15a9@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Sort the kerneldoc entries the same way the struct members are
sorted.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v7-3-815606092fff@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Some nodes, like EBI0 (DDR) or L3/LLCC, may be connected over more than
one channel. This should be taken into account in bandwidth calcualtion,
as we're supposed to feed msmbus with the per-channel bandwidth. Add
support for specifying that and use it during bandwidth aggregation.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v7-2-815606092fff@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Currently NOC_QOS_MODE_FIXED is defined as 0x0 which makes it the
default option (partial struct initialization). The default option
however should be NOC_QOS_MODE_INVALID.
That results in bogus QoS configurations being sent for port 0 (which
is used for the DRAM endpoint on BIMC, for example) coming from all nodes
with .qos.ap_owned = true and uninitialized .qos.qos_mode. It's also an
issue for newer SoCs where all nodes are treated as if they were ap_owned,
but not all of them have QoS configuration.
The NOC_QOS_MODEs are defined as preprocessor constants and are not used
anywhere outside qcom_icc_set_noc_qos(), which is easily worked around.
Separate the desc->type values from the values sent to msmbus in the
aforementioned function. Make the former an enum for better mainainability.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230228-topic-qos-v7-1-815606092fff@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Any power domain would already have been attached by the platform bus
code so drop the bogus power domain attach which always succeeds from
probe.
This effectively reverts commit 7de109c0ab ("interconnect: icc-rpm:
Add support for bus power domain").
Fixes: 7de109c0ab ("interconnect: icc-rpm: Add support for bus power domain")
Cc: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # MSM8996 Sony Kagura
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230313084953.24088-3-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The commit 4529992c94 ("interconnect: qcom: osm-l3: Use
platform-independent node ids") made osm-l3 driver use
platform-independent IDs, removing the need to include platform headers.
Fixes: 4529992c94 ("interconnect: qcom: osm-l3: Use platform-independent node ids")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230103031159.1060075-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Since Qualcomm platforms have switched to the separate OSM_L3/EPSS
driver, old related defines became unused. Drop them now.
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Fixes: 4529992c94 ("interconnect: qcom: osm-l3: Use platform-independent node ids")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230103045717.1079067-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230209101310.11942cd0@endymion.delvare
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current interconnect provider registration interface is inherently
racy as nodes are not added until the after adding the provider. This
can specifically cause racing DT lookups to fail.
Switch to using the new API where the provider is not registered until
after it has been fully initialised.
Fixes: 4e60a9568d ("interconnect: qcom: add msm8974 driver")
Cc: stable@vger.kernel.org # 5.5
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-12-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current interconnect provider registration interface is inherently
racy as nodes are not added until the after adding the provider. This
can specifically cause racing DT lookups to fail.
Switch to using the new API where the provider is not registered until
after it has been fully initialised.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Cc: stable@vger.kernel.org # 5.7
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-11-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Make sure to clean up and release resources properly also in case probe
fails when populating child devices.
Fixes: 57eb14779d ("interconnect: qcom: icc-rpmh: Support child NoC device probe")
Cc: stable@vger.kernel.org # 6.0
Cc: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-10-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current interconnect provider registration interface is inherently
racy as nodes are not added until the after adding the provider. This
can specifically cause racing DT lookups to fail.
Switch to using the new API where the provider is not registered until
after it has been fully initialised.
Fixes: 62feb14ee8 ("interconnect: qcom: Consolidate interconnect RPM support")
Fixes: 30c8fa3ec6 ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Cc: stable@vger.kernel.org # 5.7
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-9-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Make sure to clean up and release resources properly also in case probe
fails when populating child devices.
Fixes: e39bf2972c ("interconnect: icc-rpm: Support child NoC device probe")
Cc: stable@vger.kernel.org # 5.17
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-7-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current interconnect provider registration interface is inherently
racy as nodes are not added until the after adding the provider. This
can specifically cause racing DT lookups to fail:
of_icc_xlate_onecell: invalid index 0
cpu cpu0: error -EINVAL: error finding src node
cpu cpu0: dev_pm_opp_of_find_icc_paths: Unable to get path0: -22
qcom-cpufreq-hw: probe of 18591000.cpufreq failed with error -22
Switch to using the new API where the provider is not registered until
after it has been fully initialised.
Fixes: 5bc9900add ("interconnect: qcom: Add OSM L3 interconnect provider support")
Cc: stable@vger.kernel.org # 5.7
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-6-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Change sm8550 interconnect driver to use generic qcom_icc_rpmh_*
functions rather than embedding a copy of thema. This also fixes an
overallocation of memory for icc_onecell_data structure.
Fixes: e6f0d6a30f ("interconnect: qcom: Add SM8550 interconnect provider driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-4-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Change sm8450 interconnect driver to use generic qcom_icc_rpmh_*
functions rather than embedding a copy of thema. This also fixes an
overallocation of memory for icc_onecell_data structure.
Fixes: fafc114a46 ("interconnect: qcom: Add SM8450 interconnect provider driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-3-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This is a struct with a trailing zero-length array of icc_node pointers
but it's allocated as if it were a single array of icc_nodes instead.
Fortunately this overallocates memory rather then allocating less memory
than required.
Fix by replacing devm_kcalloc() with devm_kzalloc() and struct_size()
macro.
Fixes: 5bc9900add ("interconnect: qcom: Add OSM L3 interconnect provider support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230105002221.1416479-2-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Here are the interconnect changes for the 6.3-rc1 merge window with the
significant part being new drivers.
Driver changes:
- New driver for Qualcomm SM8550
- New driver for Qualcomm QDU1000/QRU1000
- New driver for Qualcomm SDM670
- New driver for Qualcomm SA8775P
- Drop the IP0 interconnects and migrate them to RPMh clocks instead
- Misc improvements in the DT schema for some existing drivers
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/mVV
-----END PGP SIGNATURE-----
Merge tag 'icc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 6.3
Here are the interconnect changes for the 6.3-rc1 merge window with the
significant part being new drivers.
Driver changes:
- New driver for Qualcomm SM8550
- New driver for Qualcomm QDU1000/QRU1000
- New driver for Qualcomm SDM670
- New driver for Qualcomm SA8775P
- Drop the IP0 interconnects and migrate them to RPMh clocks instead
- Misc improvements in the DT schema for some existing drivers
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc: (25 commits)
dt-bindings: interconnect: samsung,exynos-bus: allow opp-table
dt-bindings: interconnect: qcom,sa8775p-rpmh: fix a typo
dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm
interconnect: qcom: add a driver for sa8775p
dt-bindings: interconnect: qcom: document the interconnects for sa8775p
interconnect: qcom: add sdm670 interconnects
dt-bindings: interconnect: add sdm670 interconnects
dt-bindings: interconnect: OSM L3: Add SM6350 OSM L3 compatible
dt-bindings: interconnect: qcom-bwmon: document SM8550 compatibles
dt-bindings: interconnect: split SM8450 to own schema
dt-bindings: interconnect: split SC8280XP to own schema
dt-bindings: interconnect: split SC7280 to own schema
dt-bindings: interconnect: qcom: drop IPA_CORE related defines
dt-bindings: interconnect: qcom: Remove ipa-virt compatibles
interconnect: qcom: sc8280xp: Drop IP0 interconnects
interconnect: qcom: sc8180x: Drop IP0 interconnects
interconnect: qcom: sm8250: Drop IP0 interconnects
interconnect: qcom: sm8150: Drop IP0 interconnects
interconnect: move ignore_list out of of_count_icc_providers()
interconnect: qcom: sc7180: drop IP0 remnants
...
* icc-sa8775p
dt-bindings: interconnect: qcom: document the interconnects for sa8775p
interconnect: qcom: add a driver for sa8775p
dt-bindings: interconnect: qcom,sa8775p-rpmh: fix a typo
Link: https://lore.kernel.org/r/20230118140825.242544-2-brgl@bgdev.pl
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Commits 2f3724930e ("interconnect: qcom: sc7180: Drop IP0
interconnects") and 2fb251c265 ("interconnect: qcom: sdx55: Drop IP0
interconnects") removed IP0 interconnects (and ipa-virt devices support)
in favour of the RPMH clocks. Follow this example for other platforms
defining IP0 RPMH resource. While we are at it, remove several leftover
from the mentioned patches.
* icc-ip0-migration:
interconnect: qcom: sdx55: drop IP0 remnants
interconnect: qcom: sc7180: drop IP0 remnants
interconnect: move ignore_list out of of_count_icc_providers()
interconnect: qcom: sm8150: Drop IP0 interconnects
interconnect: qcom: sm8250: Drop IP0 interconnects
interconnect: qcom: sc8180x: Drop IP0 interconnects
interconnect: qcom: sc8280xp: Drop IP0 interconnects
dt-bindings: interconnect: qcom: Remove ipa-virt compatibles
dt-bindings: interconnect: qcom: drop IPA_CORE related defines
Link: https://lore.kernel.org/r/20230109002935.244320-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Similar to the sdx55 and sc7180, let's drop the MASTER_IPA_CORE and
SLAVE_IPA_CORE interconnects for this platform. There are no actual users
of this interconnect. The IP0 resource will be handled by clk-rpmh
driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-8-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Similar to the sdx55 and sc7180, let's drop the MASTER_IPA_CORE and
SLAVE_IPA_CORE interconnects for this platofm. There are no actual users
of this intercoonect. The IP0 resource will be handled by clk-rpmh
driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-7-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Similar to the sdx55 and sc7180, let's drop the MASTER_IPA_CORE and
SLAVE_IPA_CORE interconnects for this platform. There are no actual users
of this interconnect. The IP0 resource will be handled by clk-rpmh
driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-6-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Similar to the sdx55 and sc7180, let's drop the MASTER_IPA_CORE and
SLAVE_IPA_CORE interconnects for this platform. There are no actual users
of this interconnect. The IP0 resource will be handled by clk-rpmh
driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-5-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Drop two defines leftover from the commit 2f3724930e ("interconnect:
qcom: sc7180: Drop IP0 interconnects"), which dropped handling of the
IP0 resource in favour of handling it in the clk-rpmh driver.
Fixes: 2f3724930e ("interconnect: qcom: sc7180: Drop IP0 interconnects")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-3-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Drop two defines leftover from the commit 2fb251c265 ("interconnect:
qcom: sdx55: Drop IP0 interconnects"), which dropped handling of the IP0
resource in favour of handling it in the clk-rpmh driver.
Fixes: 2fb251c265 ("interconnect: qcom: sdx55: Drop IP0 interconnects")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230109002935.244320-2-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
It turned out that - very unfortunately - msm8996 needs a binding
update, adding 2 more clocks to the A2NoC node. Use the _optional
variant of devm_clk_get to make sure old DTs will still probe with
newer versions of the driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Link: https://lore.kernel.org/r/20221210200353.418391-5-konrad.dybcio@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The device tree reg starts at BUS_BASE + QoS_OFFSET, but the regmap
configs in the ICC driver had values suggesting the reg started at
BUS_BASE. Shrink them down (where they haven't been already, so for
providers where QoS_OFFSET = 0) to make sure they stay within their
window.
Fixes: 7add937f52 ("interconnect: qcom: Add MSM8996 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Link: https://lore.kernel.org/r/20221210200353.418391-4-konrad.dybcio@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
On eMMC devices the bootloader has no business enabling UFS clocks.
That results in a platform hang and hard reboot when trying to vote
on paths including MASTER_UFS and since sync_state guarantees that
it's done at boot time, this effectively prevents such devices from
booting. Fix that.
Fixes: 7add937f52 ("interconnect: qcom: Add MSM8996 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Link: https://lore.kernel.org/r/20221210200353.418391-3-konrad.dybcio@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add driver for the Qualcomm interconnect buses found in SM8550 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221202232054.2666830-3-abel.vesa@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The SC8280XP currently shows depressing results in memory benchmarks.
Fix this by introducing support for the platform in the OSM (and EPSS)
L3 driver and support for the platform in the bwmon binding.
Link: https://lore.kernel.org/r/20221111032515.3460-1-quic_bjorande@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220924015043.25130-1-shangxiaojing@huawei.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The aggregation over votes for all nodes in the provider will always
only find the bandwidth votes for the destination side of the path.
Further more, the average kBps value will always be 0.
Simplify the logic by directly looking at the destination node's peak
bandwidth request.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20221111032515.3460-5-quic_bjorande@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The EPSS instance in e.g. SM8350 and SC8280XP has per-core L3 voting
enabled. In this configuration, the "shared" vote is done using the
REG_L3_VOTE register instead of PERF_STATE.
Rename epss_l3 to clarify that it's affecting the PERF_STATE register
and add a new L3_VOTE description. Given platform lineage it's assumed
that the L3_VOTE-based case will be the predominant one, so use this for
a new generic qcom,epss-l3 compatible.
While adding the EPSS generic, also add qcom,osm-l3.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20221111032515.3460-4-quic_bjorande@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Each platform defines their own OSM L3 descriptor, but in practice
there's only two: one for OSM and one for EPSS. Remove the duplicated
definitions.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20221111032515.3460-3-quic_bjorande@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The identifiers used for nodes needs to be unique in the running system,
but defining them per platform results in a lot of duplicated
definitions and prevents us from using generic compatibles.
As these identifiers are not exposed outside the kernel, change to use
driver-local numbers, picked completely at random.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20221111032515.3460-2-quic_bjorande@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Today remove callbacks of platform devices return an int. This is unfortunate
because the device core ignores the return value and so the platform code only
emits a warning (and still removes the device).
The longterm quest is to make these remove callbacks return void instead.
This series is a preparation for that, with the goal to make the remove
callbacks obviously always return 0. This way when the prototype of
these functions is changed to return void, the change is straight
forward and easy to review.
Link: https://lore.kernel.org/r/20220718121409.171773-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Make INTERCONNECT_QCOM tristate so that icc-common.c can be
compiled as a module.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914064122.16222-1-quic_hyiwei@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
icc_provider_del() already emits an error message on failure. In this
case letting .remove() return the corresponding error code results in
another error message and the device is removed anyhow. (See
platform_remove().)
So ignore the return value of icc_provider_del() and return 0
unconditionally.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220718121409.171773-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
icc_provider_del() already emits an error message on failure. In this
case letting .remove() return the corresponding error code results in
another error message and the device is removed anyhow. (See
platform_remove().)
So ignore the return value of icc_provider_del() and return 0
unconditionally.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220718121409.171773-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
icc_provider_del() already emits an error message on failure. In this
case letting .remove() return the corresponding error code results in
another error message and the device is removed anyhow. (See
platform_remove().)
So ignore the return value of icc_provider_del() and return 0
unconditionally.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220718121409.171773-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
icc_provider_del() already emits an error message on failure. In this
case letting .remove() return the corresponding error code results in
another error message and the device is removed anyhow. (See
platform_remove().)
So ignore the return value of icc_provider_del() and return 0
unconditionally.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220718121409.171773-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
icc_provider_del() already emits an error message on failure. In this
case letting .remove() return the corresponding error code results in
another error message and the device is removed anyhow. (See
platform_remove().)
So ignore the return value of icc_provider_del() and return 0
unconditionally.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220718121409.171773-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This patch set is to support bucket in icc-rpm driver, so it implements
the similar mechanism in the icc-rpmh driver.
It uses interconnect path tag to indicate the bandwidth voting is for
which buckets, and there have three kinds of buckets: AWC, WAKE and
SLEEP, finally the wake and sleep bucket values are used to set the
corresponding clock (active and sleep clocks). So far, we keep the AWC
bucket but doesn't really use it.
Link: https://lore.kernel.org/r/20220712015929.2789881-1-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This commit uses buckets for support bandwidth and clock rates. It
introduces a new function qcom_icc_bus_aggregate() to calculate the
aggregate average and peak bandwidths for every bucket, and also it
calculates the maximum value of aggregated average bandwidth across all
buckets.
The maximum aggregated average is used to calculate the final bandwidth
requests. And we can set the clock rate per bucket, we use SLEEP bucket
as default bucket if a platform doesn't enable the interconnect path
tags in DT binding; otherwise, we use WAKE bucket to set active clock
and use SLEEP bucket for other clocks. So far we don't use AMC bucket.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220712015929.2789881-6-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current interconnect rpm driver uses a single aggregate bandwidth to
calculate the clock rates for both active and sleep clocks; therefore,
it has no chance to separate bandwidth requests for these two kinds of
clocks.
This patch studies the implementation from interconnect rpmh driver to
support multiple buckets. The rpmh driver provides three buckets for
AMC, WAKE, and SLEEP; this driver only needs to use WAKE and SLEEP
buckets, but we keep the same way with rpmh driver, this can allow us to
reuse the DT binding and avoid to define duplicated data structures.
This patch introduces two callbacks: qcom_icc_pre_bw_aggregate() is used
to clean up bucket values before aggregate bandwidth requests, and
qcom_icc_bw_aggregate() is to aggregate bandwidth for buckets.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220712015929.2789881-5-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This commit changes to use callback qcom_icc_xlate_extended(). This
is a preparation for population path tags from the interconnect DT
binding, it doesn't introduce functionality change for the existed DT
binding without path tags.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220712015929.2789881-4-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
since there have conflict between two headers icc-rpmh.h and icc-rpm.h,
the function qcom_icc_xlate_extended() is declared in icc-rpmh.h thus
it cannot be used by icc-rpm driver.
Move the function to a new common file icc-common.c so that allow it to
be called by multiple drivers.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220712015929.2789881-3-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Make it possible to set destination as well as source bandwidth. If the
*dst pointer is non-NULL. Right now it appears that we never make the
destination bw allocation call, which is inconsistent with the downstream
way of doing this.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20220707093823.1691870-1-bryan.odonoghue@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
It's fashion to use the icc_sync_state callback to notify the framework
when all consumers are probed, so that the bandwidth request doesn't
need to stay on maximum value.
Do the same thing for msm8939 driver.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220416012634.479617-1-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This patch set is to address two clock rate setting issues.
The first patch is to fix a potential cached clock rate mismatching
issue, the issue can lead to the clock rate is missed to be set. Note,
since this potential issue requires specific time window and certain
condition (consumers need to request the same bandwidth) to produce,
the patch is based on analysis but not a real trace log.
The second patch is an extension to cache clock rates for active and
sleep clocks separately, with this change it gives us possibility to set
active and sleep clock with different clock rates.
* icc-rpm
interconnect: qcom: icc-rpm: Fix for cached clock rate
interconnect: qcom: icc-rpm: Cache every clock rate
Link: https://lore.kernel.org/r/20220416031029.693211-1-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This contains a few fixes for the sc8180x interconnect provider driver to make
it functional.
* icc-sc8180x
dt-bindings: interconnect: Add SC8180X QUP0 virt provider
interconnect: qcom: sc8180x: Modernize sc8180x probe
interconnect: qcom: sc8180x: Fix QUP0 nodes
interconnect: qcom: sc8180x: Mark some BCMs keepalive
Link: https://lore.kernel.org/r/20220503211925.1022169-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The Qualcomm interconnect providers started off defining nodes and BCMs
using the DEFINE_QNODE() and DEFINE_QBCM() macros. Unfortunately this
results in a block of long lines that are hard to read, a transition to
explicitly stated definition has been made for newly introduced
platforms.
Transition the SC8180X interconnect provider driver to this style as
well, to make it easier to read while debugging interconnect related
issues.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220503225300.1141814-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The QUP0 BCM relates to some internal property of the QUPs, and should
be configured independently of the path to the QUP. In line with other
platforms expose QUP_CORE endpoints in order allow this configuration.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220503211925.1022169-4-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The introduction of the Qualcomm SC8180X provider raced with the
refactoring of the RPMh common code and SC8180X was left with the old
style of duplicating the probe function in each provider driver.
Transition the driver to the "new" design.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220503211925.1022169-3-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The cached clock rate is used for all bus clocks, thus it has the
assumption that all interconnect clock rates are always same, this
causes trouble if we want to set different clock rates separately.
This patch is to allocate a clock rate array to cache every clock
rate.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220416031029.693211-3-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
All nodes within an interconnect bus share interconnect bus clocks, but
every node has its own cached clock rate values, this can lead to
unexpected clock rate setting.
Let's see an example shown in below, in this case, a bus have two nodes
A and B, and its buswidth is 8:
step1: vote bandwidth 1600M for node(A):
aggregated(bw) = 1600M
qcom_icc_node(A)->rate = 1600M / 8 = 200MHz
step2: vote bandwidth 1600M for node(B):
aggregated(bw) = 1600M + 1600M = 3200M
qcom_icc_node(B)->rate = 3200M / 8 = 400MHz
step3: unvote bandwidth 1600M for node(A)
aggregated(bw) = 3200M - 1600M = 1600M
target_clock = 1600M / 8 = 200MHz
The problem is in step 3, the calculated target clock rate is 200MHz,
which equals to the cached clock rate in node(A) (See step 1),
unfortunately, qcom_icc_set() skips to set the new clock rate 200MHz in
this case, so the bus clock rate will continue to stay at 400MHz.
To resolve the issue, one possible solution is to invoke clk_get_rate()
to retrieve the clock rates on the fly, thus we can totally remove the
cached clock rates. But after review the code, many bus clock has set
the flag CLK_GET_RATE_NOCACHE, this results in the retrieving bus clock
rate is time cost for iterating parent clock nodes, and even challenges
bus clock drivers to provide recalc_rate() callbacks.
So this patch moves the cached rates into structure qcom_icc_provider,
we use it as a central place to maintain bus clock handlers and cached
clock rate, therefore, it can smoothly dismiss the mismatching problem.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220416031029.693211-2-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Pointers to struct qcom_icc_bcm are not modified, so they can be made
const for safety. The contents of struct qcom_icc_bcm must stay
non-const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220427131154.302581-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Pointers to struct qcom_icc_node (and similar structures) are not
modified, so they can be made const for safety. The contents of struct
qcom_icc_node must stay non-const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220427131154.302581-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
