Allow the HW to register DMA-mapped memory for kernel-level PDs.
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://patch.msgid.link/1737394039-28772-2-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When a DCT QP is created on an active lag, it's dctc.port is assigned
in a round-robin way, which is from 1 to dev->lag_port. In this case
when querying this QP, we may get qp_attr.port_num > 2.
Fix this by setting qp->port when modifying a DCT QP, and read port_num
from qp->port instead of dctc.port when querying it.
Fixes: 7c4b1ab9f1 ("IB/mlx5: Add DCT RoCE LAG support")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Link: https://patch.msgid.link/94c76bf0adbea997f87ffa27674e0a7118ad92a9.1737290358.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This patch addresses an issue in the recovery flow of the UMR QP,
ensuring tasks do not get stuck, as highlighted by the call trace [1].
During recovery, before transitioning the QP to the RESET state, the
software must wait for all outstanding WRs to complete.
Failing to do so can cause the firmware to skip sending some flushed
CQEs with errors and simply discard them upon the RESET, as per the IB
specification.
This race condition can result in lost CQEs and tasks becoming stuck.
To resolve this, the patch sends a final WR which serves only as a
barrier before moving the QP state to RESET.
Once a CQE is received for that final WR, it guarantees that no
outstanding WRs remain, making it safe to transition the QP to RESET and
subsequently back to RTS, restoring proper functionality.
Note:
For the barrier WR, we simply reuse the failed and ready WR.
Since the QP is in an error state, it will only receive
IB_WC_WR_FLUSH_ERR. However, as it serves only as a barrier we don't
care about its status.
[1]
INFO: task rdma_resource_l:1922 blocked for more than 120 seconds.
Tainted: G W 6.12.0-rc7+ #1626
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:rdma_resource_l state:D stack:0 pid:1922 tgid:1922 ppid:1369
flags:0x00004004
Call Trace:
<TASK>
__schedule+0x420/0xd30
schedule+0x47/0x130
schedule_timeout+0x280/0x300
? mark_held_locks+0x48/0x80
? lockdep_hardirqs_on_prepare+0xe5/0x1a0
wait_for_completion+0x75/0x130
mlx5r_umr_post_send_wait+0x3c2/0x5b0 [mlx5_ib]
? __pfx_mlx5r_umr_done+0x10/0x10 [mlx5_ib]
mlx5r_umr_revoke_mr+0x93/0xc0 [mlx5_ib]
__mlx5_ib_dereg_mr+0x299/0x520 [mlx5_ib]
? _raw_spin_unlock_irq+0x24/0x40
? wait_for_completion+0xfe/0x130
? rdma_restrack_put+0x63/0xe0 [ib_core]
ib_dereg_mr_user+0x5f/0x120 [ib_core]
? lock_release+0xc6/0x280
destroy_hw_idr_uobject+0x1d/0x60 [ib_uverbs]
uverbs_destroy_uobject+0x58/0x1d0 [ib_uverbs]
uobj_destroy+0x3f/0x70 [ib_uverbs]
ib_uverbs_cmd_verbs+0x3e4/0xbb0 [ib_uverbs]
? __pfx_uverbs_destroy_def_handler+0x10/0x10 [ib_uverbs]
? __lock_acquire+0x64e/0x2080
? mark_held_locks+0x48/0x80
? find_held_lock+0x2d/0xa0
? lock_acquire+0xc1/0x2f0
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
? __fget_files+0xc3/0x1b0
ib_uverbs_ioctl+0xe7/0x170 [ib_uverbs]
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
__x64_sys_ioctl+0x1b0/0xa70
do_syscall_64+0x6b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f99c918b17b
RSP: 002b:00007ffc766d0468 EFLAGS: 00000246 ORIG_RAX:
0000000000000010
RAX: ffffffffffffffda RBX: 00007ffc766d0578 RCX:
00007f99c918b17b
RDX: 00007ffc766d0560 RSI: 00000000c0181b01 RDI:
0000000000000003
RBP: 00007ffc766d0540 R08: 00007f99c8f99010 R09:
000000000000bd7e
R10: 00007f99c94c1c70 R11: 0000000000000246 R12:
00007ffc766d0530
R13: 000000000000001c R14: 0000000040246a80 R15:
0000000000000000
</TASK>
Fixes: 158e71bb69 ("RDMA/mlx5: Add a umr recovery flow")
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/27b51b92ec42dfb09d8096fcbd51878f397ce6ec.1737290141.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap library
code.
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms some
cleanup and Rust preparation in the xarray library code.
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven fixes
pathnames in some code comments.
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses the
new secs_to_jiffies() in various places where that is appropriate.
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API.
- "Convert ocfs2 to use folios" from Matthew Wilcox does that.
- "Remove get_task_comm() and print task comm directly" from Yafang Shao
removes now-unneeded calls to get_task_comm() in various places.
- "squashfs: reduce memory usage and update docs" from Phillip Lougher
implements some memory savings in squashfs and performs some
maintainability work.
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work.
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented with a
corrupted image.
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc.
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger.
- "minmax.h: Cleanups and minor optimisations" from David Laight
does some maintenance work on the min/max library code.
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance work
on the xarray library code.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ5SP5QAKCRDdBJ7gKXxA
jqN7AQChvwXGG43n4d5SDiA/rH7ddvowQcDqhC9cAMJ1ReR7qwEA8/LIWDE4PdMX
mJnaZ1/ibpEpearrChCViApQtcyEGQI=
=ti4E
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
Lighter that normal, but the now usual collection of driver fixes and
small improvements:
- Small fixes and minor improvements to cxgb4, bnxt_re, rxe, srp, efa,
cxgb4
- Update mlx4 to use the new umem APIs, avoiding direct use of scatterlist
- Support ROCEv2 in erdma
- Remove various uncalled functions, constify bin_attribute
- Provide core infrastructure to catch netdev events and route them to
drivers, consolidating duplicated driver code
- Fix rare race condition crashes in mlx5 ODP flows
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZ5JkNAAKCRCFwuHvBreF
YeCwAP9nrzFZMBEa0DVx7V8w3sotQCOzaaoi+4UOigeleppKSAD+K7QA5CIwNf7j
x0apvJlNsXKSYJVUI2rch/qIL8ckQwM=
=wIYu
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Lighter that normal, but the now usual collection of driver fixes and
small improvements:
- Small fixes and minor improvements to cxgb4, bnxt_re, rxe, srp,
efa, cxgb4
- Update mlx4 to use the new umem APIs, avoiding direct use of
scatterlist
- Support ROCEv2 in erdma
- Remove various uncalled functions, constify bin_attribute
- Provide core infrastructure to catch netdev events and route them
to drivers, consolidating duplicated driver code
- Fix rare race condition crashes in mlx5 ODP flows"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (63 commits)
RDMA/mlx5: Fix implicit ODP use after free
RDMA/mlx5: Fix a race for an ODP MR which leads to CQE with error
RDMA/qib: Constify 'struct bin_attribute'
RDMA/hfi1: Constify 'struct bin_attribute'
RDMA/rxe: Fix the warning "__rxe_cleanup+0x12c/0x170 [rdma_rxe]"
RDMA/cxgb4: Notify rdma stack for IB_EVENT_QP_LAST_WQE_REACHED event
RDMA/bnxt_re: Allocate dev_attr information dynamically
RDMA/bnxt_re: Pass the context for ulp_irq_stop
RDMA/bnxt_re: Add support to handle DCB_CONFIG_CHANGE event
RDMA/bnxt_re: Query firmware defaults of CC params during probe
RDMA/bnxt_re: Add Async event handling support
bnxt_en: Add ULP call to notify async events
RDMA/mlx5: Fix indirect mkey ODP page count
MAINTAINERS: Update the bnxt_re maintainers
RDMA/hns: Clean up the legacy CONFIG_INFINIBAND_HNS
RDMA/rtrs: Add missing deinit() call
RDMA/efa: Align interrupt related fields to same type
RDMA/bnxt_re: Fix to drop reference to the mmap entry in case of error
RDMA/mlx5: Fix link status down event for MPV
RDMA/erdma: Support create_ah/destroy_ah in non-sleepable contexts
...
This patch addresses a race condition for an ODP MR that can result in a
CQE with an error on the UMR QP.
During the __mlx5_ib_dereg_mr() flow, the following sequence of calls
occurs:
mlx5_revoke_mr()
mlx5r_umr_revoke_mr()
mlx5r_umr_post_send_wait()
At this point, the lkey is freed from the hardware's perspective.
However, concurrently, mlx5_ib_invalidate_range() might be triggered by
another task attempting to invalidate a range for the same freed lkey.
This task will:
- Acquire the umem_odp->umem_mutex lock.
- Call mlx5r_umr_update_xlt() on the UMR QP.
- Since the lkey has already been freed, this can lead to a CQE error,
causing the UMR QP to enter an error state [1].
To resolve this race condition, the umem_odp->umem_mutex lock is now also
acquired as part of the mlx5_revoke_mr() scope. Upon successful revoke,
we set umem_odp->private which points to that MR to NULL, preventing any
further invalidation attempts on its lkey.
[1] From dmesg:
infiniband rocep8s0f0: dump_cqe:277:(pid 0): WC error: 6, Message: memory bind operation error
cqe_dump: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000030: 00 00 00 00 08 00 78 06 25 00 11 b9 00 0e dd d2
WARNING: CPU: 15 PID: 1506 at drivers/infiniband/hw/mlx5/umr.c:394 mlx5r_umr_post_send_wait+0x15a/0x2b0 [mlx5_ib]
Modules linked in: ip6table_mangle ip6table_natip6table_filter ip6_tables iptable_mangle xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm mlx5_ib ib_uverbs ib_core fuse mlx5_core
CPU: 15 UID: 0 PID: 1506 Comm: ibv_rc_pingpong Not tainted 6.12.0-rc7+ #1626
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5r_umr_post_send_wait+0x15a/0x2b0 [mlx5_ib]
[..]
Call Trace:
<TASK>
mlx5r_umr_update_xlt+0x23c/0x3e0 [mlx5_ib]
mlx5_ib_invalidate_range+0x2e1/0x330 [mlx5_ib]
__mmu_notifier_invalidate_range_start+0x1e1/0x240
zap_page_range_single+0xf1/0x1a0
madvise_vma_behavior+0x677/0x6e0
do_madvise+0x1a2/0x4b0
__x64_sys_madvise+0x25/0x30
do_syscall_64+0x6b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: e6fb246cca ("RDMA/mlx5: Consolidate MR destruction to mlx5_ib_dereg_mr()")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/r/68a1e007c25b2b8fe5d625f238cc3b63e5341f77.1737290229.git.leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Artemy Kovalyov <artemyko@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This patch sends IB_EVENT_QP_LAST_WQE_REACHED event on a QP that is in
error state and associated with an SRQ. This behaviour is incorporated
in flush_qp() which is called when QP transitions to error state.
Supports SRQ drain functionality added by commit 844bc12e6d ("IB/core:
add support for draining Shared receive queues")
Fixes: 844bc12e6d ("IB/core: add support for draining Shared receive queues")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://patch.msgid.link/20250107095053.81007-1-anumula@chelsio.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In order to optimize the size of driver private structure,
the memory for dev_attr is allocated dynamically during the
chip context initialization. In order to make certain runtime
decisions, store dev_attr in the qplib_res structure.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1736446693-6692-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
ulp_irq_stop() can be invoked from a context where FW is healthy or
when FW is in a reset state. In the latter case, ULP must stop all
interactions with HW/FW and also with application and stack. Added a
new parameter to the ulp_irq_stop() function to achieve that.
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1736446693-6692-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
QP1 context in HW needs to be updated when there is a
change in the default DSCP values used for RoCE traffic.
Handle the event from FW and modify the dscp value used
by QP1.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20250107024553.2926983-5-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Added function to query firmware default values of CC parameters
during driver init. These values will be stored in driver local
structure and used in subsequent patch.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250107024553.2926983-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Using the option provided by Ethernet driver, register for FW Async
event. During probe, while registeriung with Ethernet driver, provide
the ulp hook 'ulp_async_notifier' for receiving the firmware events.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250107024553.2926983-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Restrict the check for the number of pages handled during an ODP page
fault to direct mkeys.
Perform the check right after handling the page fault and don't
propagate the number of handled pages to callers.
Indirect mkeys and their associated direct mkeys can have different
start addresses. As a result, the calculation of the number of pages to
handle for an indirect mkey may not match the actual page fault
handling done on the direct mkey.
For example:
A 4K sized page fault on a KSM mkey that has a start address that is not
aligned to a page will result a calculation that assumes the number of
pages required to handle are 2.
While the underlying MTT might be aligned will require fetching only a
single page.
Thus, do the calculation and compare number of pages handled only per
direct mkey.
Fixes: db570d7dea ("IB/mlx5: Add ODP support to MW")
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Reviewed-by: Artemy Kovalyov <artemyko@nvidia.com>
Link: https://patch.msgid.link/86c483d9e75ce8fe14e9ff85b62df72b779f8ab1.1736187990.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Correct the spelling dictionary so that future instances will be caught by
checkpatch, and fix the instances found.
Link: https://lkml.kernel.org/r/20241211154903.47027-1-cvam0000@gmail.com
Signed-off-by: Shivam Chaudhary <cvam0000@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Shivam Chaudhary <cvam0000@gmail.com>
Cc: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
hns driver used to support hip06 and hip08 devices with
CONFIG_INFINIBAND_HNS_HIP06 and CONFIG_INFINIBAND_HNS_HIP08
respectively, which both depended on CONFIG_INFINIBAND_HNS.
But we no longer provide support for hip06 and only support
hip08 and higher since the commit in fixes line, so there is
no need to have CONFIG_INFINIBAND_HNS any more. Remove it and
only keep CONFIG_INFINIBAND_HNS_HIP08.
Fixes: 38d2208824 ("RDMA/hns: Remove support for HIP06")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250106111211.3945051-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
There is a lot of implicit casting of interrupt related fields. Use
u32 as common type since this is what the device use as type for max
supported EQs and what IB core expects in num_comp_vectors field.
Reviewed-by: Daniel Kranzdorf <dkkranzd@amazon.com>
Reviewed-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Yonatan Nachum <ynachum@amazon.com>
Link: https://patch.msgid.link/20250105131421.29030-1-ynachum@amazon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In the error handling path of bnxt_re_mmap(), driver should invoke
rdma_user_mmap_entry_put() to free the reference of mmap entry in case
the error happens after rdma_user_mmap_entry_get was called.
Fixes: ea22248578 ("RDMA/bnxt_re: Update alloc_page uapi for pacing")
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20250104061519.2540178-1-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Alot of fixes accumulated over the holiday break:
- Static tool fixes, value is already proven to be NULL, possible integer
overflow
- Many bnxt_re fixes:
* Crashes due to a mismatch in the maximum SGE list size
* Don't waste memory for user QPs by creating kernel-only structures
* Fix compatability issues with older HW in some of the new HW features
recently introduced: RTS->RTS feature, work around 9096
* Do not allow destroy_qp to fail
* Validate QP MTU against device limits
* Add missing validation on madatory QP attributes for RTR->RTS
* Report port_num in query_qp as required by the spec
* Fix creation of QPs of the maximum queue size, and in the variable mode
* Allow all QPs to be used on newer HW by limiting a work around only to
HW it affects
* Use the correct MSN table size for variable mode QPs
* Add missing locking in create_qp() accessing the qp_tbl
* Form WQE buffers correctly when some of the buffers are 0 hop
* Don't crash on QP destroy if the userspace doesn't setup the dip_ctx
* Add the missing QP flush handler call on the DWQE path to avoid
hanging on error recovery
* Consistently use ENXIO for return codes if the devices is fatally errored
- Try again to fix VLAN support on iwarp, previous fix was reverted due to
breaking other cards
- Correct error path return code for rdma netlink events
- Remove the seperate net_device pointer in siw and rxe which syzkaller
found a way to UAF
- Fix a UAF of a stack ib_sge in rtrs
- Fix a regression where old mlx5 devices and FW were wrongly activing
new device features and failing
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZ3fvrwAKCRCFwuHvBreF
YSuIAQDNZ8fPvjVdL8x1QIUVParAAewEUv3MbmV1uRVgoG7LrQEAxgw6UIUF4HOw
u6aW8aRXGYM3hG241AKoYnU5yqHl4g0=
=ilfd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A lot of fixes accumulated over the holiday break:
- Static tool fixes, value is already proven to be NULL, possible
integer overflow
- Many bnxt_re fixes:
- Crashes due to a mismatch in the maximum SGE list size
- Don't waste memory for user QPs by creating kernel-only
structures
- Fix compatability issues with older HW in some of the new HW
features recently introduced: RTS->RTS feature, work around 9096
- Do not allow destroy_qp to fail
- Validate QP MTU against device limits
- Add missing validation on madatory QP attributes for RTR->RTS
- Report port_num in query_qp as required by the spec
- Fix creation of QPs of the maximum queue size, and in the
variable mode
- Allow all QPs to be used on newer HW by limiting a work around
only to HW it affects
- Use the correct MSN table size for variable mode QPs
- Add missing locking in create_qp() accessing the qp_tbl
- Form WQE buffers correctly when some of the buffers are 0 hop
- Don't crash on QP destroy if the userspace doesn't setup the
dip_ctx
- Add the missing QP flush handler call on the DWQE path to avoid
hanging on error recovery
- Consistently use ENXIO for return codes if the devices is
fatally errored
- Try again to fix VLAN support on iwarp, previous fix was reverted
due to breaking other cards
- Correct error path return code for rdma netlink events
- Remove the seperate net_device pointer in siw and rxe which
syzkaller found a way to UAF
- Fix a UAF of a stack ib_sge in rtrs
- Fix a regression where old mlx5 devices and FW were wrongly
activing new device features and failing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (28 commits)
RDMA/mlx5: Enable multiplane mode only when it is supported
RDMA/bnxt_re: Fix error recovery sequence
RDMA/rtrs: Ensure 'ib_sge list' is accessible
RDMA/rxe: Remove the direct link to net_device
RDMA/hns: Fix missing flush CQE for DWQE
RDMA/hns: Fix warning storm caused by invalid input in IO path
RDMA/hns: Fix accessing invalid dip_ctx during destroying QP
RDMA/hns: Fix mapping error of zero-hop WQE buffer
RDMA/bnxt_re: Fix the locking while accessing the QP table
RDMA/bnxt_re: Fix MSN table size for variable wqe mode
RDMA/bnxt_re: Add send queue size check for variable wqe
RDMA/bnxt_re: Disable use of reserved wqes
RDMA/bnxt_re: Fix max_qp_wrs reported
RDMA/siw: Remove direct link to net_device
RDMA/nldev: Set error code in rdma_nl_notify_event
RDMA/bnxt_re: Fix reporting hw_ver in query_device
RDMA/bnxt_re: Fix to export port num to ib_query_qp
RDMA/bnxt_re: Fix setting mandatory attributes for modify_qp
RDMA/bnxt_re: Add check for path mtu in modify_qp
RDMA/bnxt_re: Fix the check for 9060 condition
...
The commit below prevented MPV from unloading correctly due to blocking
the netdev down event, allow sending the event for MPV mode to maintain
proper unload flow.
Fixes: 3790137762 ("RDMA/mlx5: Handle link status event only for LAG device")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://patch.msgid.link/d7731478e456f61255af798a7fd4e64b006ddebb.1735567976.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Fixed to return ENXIO from __send_message_basic_sanity()
to indicate that device is in error state. In the case of
ERR_DEVICE_DETACHED state, the driver should not post the
commands to the firmware as it will time out eventually.
Removed bnxt_re_modify_qp() call from bnxt_re_dev_stop()
as it is a no-op.
Fixes: cc5b9b48d4 ("RDMA/bnxt_re: Recover the device when FW error is detected")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Link: https://patch.msgid.link/20241231025008.2267162-1-kalesh-anakkur.purayil@broadcom.com
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The RDMA CM module might invoke erdma_create_ah() or erdma_destroy_ah()
in a non-sleepable context. Both of these functions will call the
erdma_post_cmd_wait(), which can potentially sleep and occasionally lead
to a hard lockup. Therefore, post the create_ah and destroy_ah commands in
polling mode if the RDMA_CREATE_AH_SLEEPABLE and RDMA_DESTROY_AH_SLEEPABLE
flags are not set, respectively.
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241226084141.74823-5-boshiyu@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Several scenarios require posting commands to the cmdq in a non-sleepable
context. For example, the cm_alloc_msg() might call erdma_create_ah()
while still holding a spinlock. So we add support for non-sleeping
erdma_post_cmd_wait().
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241226084141.74823-4-boshiyu@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The erdma_post_cmd_wait() function returns the cmdq response
only when both resp0 and resp1 are not NULL.
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241226084141.74823-3-boshiyu@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Set the query_ah field to the erdma_create_ah() function and set
the size_ib_ah field to the size of struct erdma_ah.
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241226084141.74823-2-boshiyu@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Make sure the device is being reset on driver exit whatever the reason
is, to keep the device aligned and allow it to close shared resources
(e.g. admin queue).
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Reviewed-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://patch.msgid.link/20241225131548.15155-1-mrgolin@amazon.com
Reviewed-by: Gal Pressman <gal.pressman@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
hns3 NIC driver can directly notify the RoCE driver about link status
events bypassing the netdev notifier. This can provide more timely
event dispatching for ULPs.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The link status events of non-LAG devices are now handled in ib_core,
so only LAG device events need to be handled in driver.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In addition to dispatching event, some private stuffs need to be
done in this driver's link status event handler. Implement the new
report_port_event() ops with the link status event codes.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In addition to dispatching event, some private stuffs need to be
done in this driver's link status event handler. Implement the new
report_port_event() ops with the link status event codes.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In addition to dispatching event, some private stuffs need to be
done in this driver's link status event handler. Implement the new
report_port_event() ops with the link status event codes.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Since the netdev events of link status is now handled in ib_core,
remove the related code in drivers.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Since the netdev events of link status is now handled in ib_core,
remove the related code in drivers.
In addition, remove dev->state as it is only used in erdma_query_port(),
and it can be replaced by ib_get_curr_port_state().
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Since the netdev events of link status is now handled in ib_core,
remove the related code in drivers.
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
irdma_cqp_commit_fpm_val_cmd() and irdma_cqp_query_fpm_val_cmd()
were added in 2021 by
commit 915cc7ac0f ("RDMA/irdma: Add miscellaneous utility definitions")
but haven't been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20241223001613.307138-1-linux@treblig.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently mlx5_flow_destination includes counter_id which is assigned in
case we use flow counter on the flow steering rule. However, counter_id
is not enough data in case of using HW Steering. Thus, have mlx5_fc
object as part of mlx5_flow_destination instead of counter_id and assign
it where needed.
In case counter_id is received from user space, create a local counter
object to represent it.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241219175841.1094544-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flush CQE handler has not been called if QP state gets into errored
mode in DWQE path. So, the new added outstanding WQEs will never be
flushed.
It leads to a hung task timeout when using NFS over RDMA:
__switch_to+0x7c/0xd0
__schedule+0x350/0x750
schedule+0x50/0xf0
schedule_timeout+0x2c8/0x340
wait_for_common+0xf4/0x2b0
wait_for_completion+0x20/0x40
__ib_drain_sq+0x140/0x1d0 [ib_core]
ib_drain_sq+0x98/0xb0 [ib_core]
rpcrdma_xprt_disconnect+0x68/0x270 [rpcrdma]
xprt_rdma_close+0x20/0x60 [rpcrdma]
xprt_autoclose+0x64/0x1cc [sunrpc]
process_one_work+0x1d8/0x4e0
worker_thread+0x154/0x420
kthread+0x108/0x150
ret_from_fork+0x10/0x18
Fixes: 01584a5edc ("RDMA/hns: Add support of direct wqe")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
WARN_ON() is called in the IO path. And it could lead to a warning
storm. Use WARN_ON_ONCE() instead of WARN_ON().
Fixes: 12542f1de1 ("RDMA/hns: Refactor process about opcode in post_send()")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
If it fails to modify QP to RTR, dip_ctx will not be attached. And
during detroying QP, the invalid dip_ctx pointer will be accessed.
Fixes: faa62440a5 ("RDMA/hns: Fix different dgids mapping to the same dip_idx")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Due to HW limitation, the three region of WQE buffer must be mapped
and set to HW in a fixed order: SQ buffer, SGE buffer, and RQ buffer.
Currently when one region is zero-hop while the other two are not,
the zero-hop region will not be mapped. This violate the limitation
above and leads to address error.
Fixes: 38389eaa4d ("RDMA/hns: Add mtr support for mixed multihop addressing")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Fix conditional if else check by checking with wr->opcode.
The indicated dead code may have performed some action; that
action will never occur as op is pre-assigned a different value.
Fixes: 999a0a2e9b ("RDMA/erdma: Support UD QPs and UD WRs")
Signed-off-by: Advait Dhamorikar <advaitdhamorikar@gmail.com>
Link: https://patch.msgid.link/20241219043939.10344-1-advaitdhamorikar@gmail.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
QP table handling is synchronized with destroy QP and Async
event from the HW. The same needs to be synchronized
during create_qp also. Use the same lock in create_qp also.
Fixes: 76d3ddff71 ("RDMA/bnxt_re: synchronize the qp-handle table array")
Fixes: f218d67ef0 ("RDMA/bnxt_re: Allow posting when QPs are in error")
Fixes: 84cf229f40 ("RDMA/bnxt_re: Fix the qp table indexing")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
For variable size wqe mode, the MSN table size should be
half the size of the SQ depth. Fixing this to avoid wrap
around problems in the retransmission path.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-5-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
For the fixed WQE case, HW supports 0xFFFF WQEs.
For variable Size WQEs, HW treats this number as
the 16 bytes slots. The maximum supported WQEs
needs to be adjusted based on the number of slots.
Set a maximum WQE limit for variable WQE scenario.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Disabling the reserved wqes logic for Gen P5/P7 devices
because this workaround is required only for legacy devices.
Fixes: ecb53febfc ("RDMA/bnxt_en: Enable RDMA driver support for 57500 chip")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
While creating qps, driver adds one extra entry to the sq size
passed by the ULPs in order to avoid queue full condition.
When ULPs creates QPs with max_qp_wr reported, driver creates
QP with 1 more than the max_wqes supported by HW. Create QP fails
in this case. To avoid this error, reduce 1 entry in max_qp_wqes
and report it to the stack.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Driver currently populates subsystem_device id in the
"hw_ver" field of ib_attr structure in query_device.
Updated to populate PCI revision ID.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Preethi G <preethi.gurusiddalingeswaraswamy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Current driver implementation doesn't populate the port_num
field in query_qp. Adding the code to convert internal firmware
port id to ibv defined port number and export it.
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-5-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Firmware expects "min_rnr_timer" as a mandatory attribute in
MODIFY_QP command during the RTR-RTS transition. This needs
to be enforced by the driver which is missing while setting
bnxt_set_mandatory_attributes that sends these flags as part
of modify_qp optimization.
Fixes: 82c32d2192 ("RDMA/bnxt_re: Add support for optimized modify QP")
Reviewed-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When RDMA app configures path MTU, add a check in modify_qp verb
to make sure that it doesn't go beyond interface MTU. If this
check fails, driver will fail the modify_qp verb.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The check for 9060 condition should only be made for legacy chips.
Fixes: 9152e0b722 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
There is no need to include bnxt_ulp.h in ib_verbs.c.
Remove it. Also, fixed hw_counters.c to remove unwanted
header file inclusions.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1733888745-30939-6-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Move the function definition of bnxt_re_shutdown() to avoid
forward declarartion of bnxt_re_dev_uninit().
Move the function definition of bnxt_re_setup_cc() before
bnxt_re_add_device() to avoid it's forward declarations.
Also, forward declarartions of bnxt_re_stop_irq() and
bnxt_re_dev_stop() are unnecessary.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1733888745-30939-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Optimize error handling path in bnxt_re_probe by removing
some duplicate code.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1733888745-30939-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Return directly in case of error without a goto label as there
is no cleanup actions performed.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1733888745-30939-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The iWARP protocol supports only RC QPs previously. Now we add UD QPs
and UD WRs support for the RoCEv2 protocol.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-9-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Certian QP attributes, such as sq_draining, can only be obtained
by querying the hardware on the erdma RoCEv2 device. To address this,
we add the query_qp command to the cmdq and parse the response to
retrieve corresponding QP attributes.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-8-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The procedure for modifying QP is similar for both the iWARP and
RoCEv2 protocols. Therefore, we unify the code and provide the
erdma_modify_qp() interface for both protocols.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-7-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The QP state machines in the RoCEv2 and iWARP protocols are
different. To handle these differences for the erdma RoCEv2
device, we provide the erdma_modify_qp_rocev2() interface,
which transitions the QP state and modifies QP attributes
accordingly.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-6-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The address handle contains the necessary information to transmit
messages to a remote peer in the RoCEv2 protocol. This commit
implements the erdma_create_ah(), erdma_destroy_ah(), and
erdma_query_ah() interfaces, which are used to create, destroy,
and query an address handle, respectively.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-5-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The erdma_query_pkey() interface queries the PKey at the specified
index. Currently, erdma supports only one partition and returns the
default PKey for each query. Besides, the correct length of the PKey
table can be obtained by calling the erdma_query_port() and
erdma_get_port_immutable() interfaces.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-4-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The erdma_add_gid() interface inserts a GID entry at the
specified index. The erdma_del_gid() interface deletes the
GID entry at the specified index. Additionally, programs
can invoke the erdma_query_port() and erdma_get_port_immutable()
interfaces to query the GID table length.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-3-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently, the erdma driver supports both the iWARP and RoCEv2 protocols.
The erdma driver reads the ERDMA_REGS_DEV_PROTO_REG register to identify
the protocol used by the erdma device. Since each protocol requires
different ib_device_ops, we introduce the erdma_device_ops_iwarp and
erdma_device_ops_rocev2 for iWARP and RoCEv2 protocols, respectively.
Signed-off-by: Boshi Yu <boshiyu@linux.alibaba.com>
Link: https://patch.msgid.link/20241211020930.68833-2-boshiyu@linux.alibaba.com
Reviewed-by: Cheng Xu <chengyou@linux.alibaba.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The "gl->tot_len" variable is controlled by the user. It comes from
process_responses(). On 32bit systems, the "gl->tot_len + sizeof(struct
cpl_pass_accept_req) + sizeof(struct rss_header)" addition could have an
integer wrapping bug. Use size_add() to prevent this.
Fixes: 1cab775c3e ("RDMA/cxgb4: Fix LE hash collision bug for passive open connection")
Link: https://patch.msgid.link/r/86b404e1-4a75-4a35-a34e-e3054fa554c7@stanley.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The current ODP counters represent the total number of pages
handled, but it is not enough to understand the effectiveness
of these operations.
Extend the ODP counters to include the number of times page fault
and invalidation events were handled.
Example for a single page fault handling 512 pages:
- page_fault: incremented by 512 (total pages)
- page_fault_handled: incremented by 1 (operation count)
The same example is applicable for page invalidation too.
Previous output:
$ rdma stat mr
dev rocep8s0f0 mrn 8 page_faults 27 page_invalidations 0 page_prefetch 29
New output:
$ rdma stat mr
dev rocep8s0f0 mrn 21 page_faults 512 page_faults_handled 1
page_invalidations 0 page_invalidations_handled 0 page_prefetch 51200
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/b18f29ed1392996ade66e9e6c45f018925253f6a.1733234165.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Smatch generates the following false error report:
drivers/infiniband/hw/mlx4/main.c:393 mlx4_ib_del_gid() error: uninitialized symbol 'gids'.
Traditionally, we are not changing kernel code and asking people to fix
the tools. However in this case, the fix can be done by simply rearranging
the code to be more clear.
Fixes: e26be1bfef ("IB/mlx4: Implement ib_device callbacks")
Link: https://patch.msgid.link/6a3a1577463da16962463fcf62883a87506e9b62.1733233426.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Change bnxt_re_destroy_qp to always return 0 and don't fail
in case of error during destroy.
In addition, delete debugfs QP to earlier stage.
Fixes: d7d54769c0 ("RDMA/bnxt_re: Add debugfs hook in the driver")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The workaround to modify the UD QP from RTS to RTS is required
only for older adapters. Issuing this for latest adapters can caus
some unexpected behavior. Fix it
Fixes: 1801d87b35 ("RDMA/bnxt_re: Support new 5760X P7 devices")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Software Queues to hold the WRs needs to be created
for only kernel queues. Avoid allocating the unnecessary
memory for user Queues.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: 159fb4ceac ("RDMA/bnxt_re: introduce a function to allocate swq")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Gen P7 supports up to 13 SGEs for now. WQE software structure
can hold only 6 now. Since the max send sge is reported as
13, the stack can give requests up to 13 SGEs. This is causing
traffic failures and system crashes.
Use the define for max SGE supported for variable size. This
will work for both static and variable WQEs.
Fixes: 227f51743b ("RDMA/bnxt_re: Fix the max WQE size for static WQE support")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241204075416.478431-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Different core device types such as PFs and VFs shouldn't be affiliated
together since they have different capabilities, fix that by enforcing
type check before doing the affiliation.
Fixes: 32f69e4be2 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/88699500f690dff1c1852c1ddb71f8a1cc8b956e.1733233480.git.leonro@nvidia.com
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
res->dattr is always valid at this point as it was initialized
during device addition in bnxt_re_add_device().
This change is fixing the following smatch error:
drivers/infiniband/hw/bnxt_re/qplib_fp.c:1090 bnxt_qplib_create_qp()
error: we previously assumed 'res->dattr' could be null (see line 985)
Fixes: 07f830ae49 ("RDMA/bnxt_re: Adds MSN table capability for Gen P7 adapters")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202411222329.YTrwonWi-lkp@intel.com/
Link: https://patch.msgid.link/be0d8836b64cba3e479fbcbca717acad04aae02e.1732626579.git.leonro@nvidia.com
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
Seveal fixes scattered across the drivers and a few new features:
- Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns
- Force disassociate the userspace FD when hns does an async reset
- bnxt new features for optimized modify QP to skip certain stayes, CQ
coalescing, better debug dumping
- mlx5 new data placement ordering feature
- Faster destruction of mlx5 devx HW objects
- Improvements to RDMA CM mad handling
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZz4ENwAKCRCFwuHvBreF
YQYQAP9R54r5J1Iylg+zqhCc+e/9oveuuZbfLvy/EJiEpmdprQEAgPs1RrB0z7U6
1xrVStUKNPhGd5XeVVZGkIV0zYv6Tw4=
=V5xI
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Seveal fixes scattered across the drivers and a few new features:
- Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns
- Force disassociate the userspace FD when hns does an async reset
- bnxt new features for optimized modify QP to skip certain stayes,
CQ coalescing, better debug dumping
- mlx5 new data placement ordering feature
- Faster destruction of mlx5 devx HW objects
- Improvements to RDMA CM mad handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (51 commits)
RDMA/bnxt_re: Correct the sequence of device suspend
RDMA/bnxt_re: Use the default mode of congestion control
RDMA/bnxt_re: Support different traffic class
IB/cm: Rework sending DREQ when destroying a cm_id
IB/cm: Do not hold reference on cm_id unless needed
IB/cm: Explicitly mark if a response MAD is a retransmission
RDMA/mlx5: Move events notifier registration to be after device registration
RDMA/bnxt_re: Cache MSIx info to a local structure
RDMA/bnxt_re: Refurbish CQ to NQ hash calculation
RDMA/bnxt_re: Refactor NQ allocation
RDMA/bnxt_re: Fail probe early when not enough MSI-x vectors are reserved
RDMA/hns: Fix different dgids mapping to the same dip_idx
RDMA/bnxt_re: Add set_func_resources support for P5/P7 adapters
RDMA/bnxt_re: Enhance RoCE SRIOV resource configuration design
bnxt_en: Add support for RoCE sriov configuration
RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
RDMA/hns: Fix out-of-order issue of requester when setting FENCE
RDMA/nldev: Add IB device and net device rename events
RDMA/mlx5: Add implementation for ufile_hw_cleanup device operation
RDMA/core: Move ib_uverbs_file struct to uverbs_types.h
...
When in fatal error condition, mark device as detached first
and then complete all pending HWRM commands as firmware is not
going to process them and eventually time out. Move the device
to error only if suspend is called when device is in Fatal state.
Also, remove some outdated comments. Remove the stop_irq call
which is no longer required.
Fixes: cc5b9b48d4 ("RDMA/bnxt_re: Recover the device when FW error is detected")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1731660464-27838-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Instead of driver setting the congestion mode, use
the default values setup by Firmware. Enable the tos_ecn
field in FW.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1731660464-27838-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Adding support for different traffic class passed
to driver. Fix the traffic class setting in modify_qp
by skipping the ECN bits. Pass the service level received
from applications to the firmware.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1731660464-27838-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
L2 driver allocates the vectors for RoCE and pass it through the
en_dev structure to RoCE. During probe, cache the MSIx related
info to a local structure.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/1731577748-1804-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
There are few use cases where CQ create and destroy
is seen before re-creating the CQ, this kind of use
case is disturbing the RR distribution and all the
active CQ getting mapped to only 2 NQ alternatively.
Fixing the CQ to NQ hash calculation by implementing
a quick load sorting mechanism under a mutex.
Using this, if the CQ was allocated and destroyed
before using it, the nq selecting algorithm still
obtains the least loaded CQ. Thus balancing the load
on NQs.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/1731577748-1804-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Move NQ related data structures from rdev to a new structure
named "struct bnxt_re_nq_record" by keeping a pointer to in
the rdev structure. Allocate the memory for it dynamically.
This change is needed for subsequent patches in the series.
Also, removed the nq_task variable from rdev structure as it
is redundant and no longer used.
This change would help to reduce the size of the driver private
structure as well.
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1731577748-1804-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
L2 driver allocates and populates the MSI-x vector details for RoCE
in the en_dev structure. RoCE driver requires minimum 2 MSIx vectors.
Hence during probe, driver has to check and bail out if there are not
enough MSI-x vectors reserved for it before proceeding further
initialization.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1731577748-1804-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
DIP algorithm requires a one-to-one mapping between dgid and dip_idx.
Currently a queue 'spare_idx' is used to store QPN of QPs that use
DIP algorithm. For a new dgid, use a QPN from spare_idx as dip_idx.
This method lacks a mechanism for deduplicating QPN, which may result
in different dgids sharing the same dip_idx and break the one-to-one
mapping requirement.
This patch replaces spare_idx with xarray and introduces a refcnt of
a dip_idx to indicate the number of QPs that using this dip_idx.
The state machine for dip_idx management is implemented as:
* The entry at an index in xarray is empty -- This indicates that the
corresponding dip_idx hasn't been created.
* The entry at an index in xarray is not empty but with 0 refcnt --
This indicates that the corresponding dip_idx has been created but
not used as dip_idx yet.
* The entry at an index in xarray is not empty and with non-0 refcnt --
This indicates that the corresponding dip_idx is being used by refcnt
number of DIP QPs.
Fixes: eb653eda1e ("RDMA/hns: Bugfix for incorrect association between dip_idx and dgid")
Fixes: f91696f2f0 ("RDMA/hns: Support congestion control type selection according to the FW")
Signed-off-by: Feng Fang <fangfeng4@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241112055553.3681129-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Enable set_func_resources for P5 and P7 adapters to handle
VF resource distribution. Remove setting max resources per VF
during PF initialization. This change is required for firmwares
which does not support RoCE VF resource management by NIC driver.
The code is same for all adapters now.
Reviewed-by: Stephen Shi <stephen.shi@broadcom.com>
Reviewed-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730882676-24434-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Refine RoCE SRIOV resource configuration design,
using the INITIALIZE_FW's flag as an indication
for the new design to the firmware. RoCE driver does not
have to provision resources to VF when firmware
advertises support for RoCE resource management by NIC driver.
Signed-off-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
CC: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730882676-24434-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
ib_map_mr_sg() allows ULPs to specify NULL as the sg_offset argument.
The driver needs to check whether it is a NULL pointer before
dereferencing it.
Fixes: d387d4b54e ("RDMA/hns: Fix missing pagesize and alignment check in FRMR")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241108075743.2652258-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The FENCE indicator in hns WQE doesn't ensure that response data from
a previous Read/Atomic operation has been written to the requester's
memory before the subsequent Send/Write operation is processed. This
may result in the subsequent Send/Write operation accessing the original
data in memory instead of the expected response data.
Unlike FENCE, the SO (Strong Order) indicator blocks the subsequent
operation until the previous response data is written to memory and a
bresp is returned. Set the SO indicator instead of FENCE to maintain
strict order.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241108075743.2652258-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the device API for ufile_hw_cleanup operation, which
iterates over the ufile uobjects lists, and attempts to destroy
DevX QPs, by issuing up to 8 commands in parallel.
This function is responsible only for cleaning the FW resources of the
QP, and doesn't necessarily cleanup all of its resources.
Hence the normal serialized cleanup flow is still executed after it
in __uverbs_cleanup_ufile() to cleanup the remaining resources and
handle the cleanup of SW objects.
In order to avoid double cleanup for the FW resources, new DevX flag
was added DEVX_OBJ_FLAGS_HW_FREED, which marks the object's FW resources
as already freed.
Since QP destruction is the most time-consuming operation in FW,
parallelizing it reduces the cleanup time of applications that use
DevX QPs.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/2f82675d0412542cba1c47a6b86f589521ae41e1.1730373303.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Fix a race condition when creating a lag bond in active backup
mode where after the bond creation the backup slave was
attached to the IB device, instead of the active slave.
This caused stale entries in the GID table, as the gid updating
mechanism relies on ib_device_get_netdev(), which would return
the backup slave.
Send an MLX5_DRIVER_EVENT_ACTIVE_BACKUP_LAG_CHANGE_LOWERSTATE
event when activating the lag, additionally to when modifying
the lag. This ensures that eventually the active netdevice is
stored in the bond IB device.
When handling this event remove the GIDs of the previously
attached netdevice in this port and rescan the GIDs of the
newly attached netdevice.
This ensures that eventually the active slave netdevice is
correctly stored in the IB device port. While there might be
a brief moment where the backup slave GIDs appear in the GID
table, it will eventually stabilize with the correct GIDs
(of the bond and the active slave).
Fixes: 8d159eb211 ("RDMA/mlx5: Use IB set_netdev and get_netdev functions")
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/91fc2cb24f63add266a528c1c702668a80416d9f.1730381292.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Support QP with out-of-order (OOO) capabilities enabled.
This allows WRs on the receiver side of the QP to be consumed OOO,
permitting the sender side to transmit messages without guaranteeing
arrival order on the receiver side.
When enabled, the completion ordering of WRs remains in-order,
regardless of the Receive WRs consumption order.
RDMA Read and RDMA Atomic operations on the responder side continue to
be executed in-order, while the ordering of data placement for RDMA
Write and Send operations is not guaranteed.
Atomic operations larger than 8 bytes are currently not supported.
Therefore, when this feature is enabled, the created QP restricts its
atomic support to 8 bytes at most.
In addition, when querying the device, a new flag is returned in
response to indicate that the Kernel supports OOO QP.
Signed-off-by: Edward Srouji <edwards@nvidia.com>
Reviewed-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/06ac609a5f358c8fb0a090d22c61a2f9329d82e6.1725362773.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Adding support for a per device debugfs folder for exporting
some of the device specific debug information.
Added support to get QP info for now. The same folder can be
used to export other debug features in future.
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Support interfaces to get the raw data for each of
the resources. Use this interface to get some of the
HW structures from active resources.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implements support for querying the hardware resource
contexts. This raw data can be used for the debugging
of the field issues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Allow users to dump driver specific resource details when
queried through rdma tool. This supports the driver data
for QP, CQ, MR and SRQ.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
If bnxt_re_add_device() fails, 'en_info' still needs to be freed, as
already done in the .remove() function.
The commit in Fixes incorrectly removed this call, certainly because it
was expecting the .remove() function was called anyway. But if the probe
fails, the remove function is not called.
There is no need to call bnxt_re_remove() as it was done before, kfree()
is enough.
Fixes: a5e099e0c4 ("RDMA/bnxt_re: Fix an error path in bnxt_re_add_device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/9e48ff955ae55fc39a9eb1eb590d374539eab5ba.1730477345.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Set port link speed and width based on max bandwidth acquired from the
device instead of using constant 100 Gbps. Use a default value in case
the device didn't set the field.
Reviewed-by: Daniel Kranzdorf <dkkranzd@amazon.com>
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://patch.msgid.link/20241030093006.21352-1-mrgolin@amazon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Invalidate rkey is cpu endian and immediate data is in big endian format.
Both immediate data and invalidate the remote key returned by
HW is in little endian format.
While handling the commit in fixes tag, the difference between
immediate data and invalidate rkey endianness was not considered.
Without changes of this patch, Kernel ULP was failing while processing
inv_rkey.
dmesg log snippet -
nvme nvme0: Bogus remote invalidation for rkey 0x2000019Fix in this patch
Do endianness conversion based on completion queue entry flag.
Also, the HW completions are already converted to host endianness in
bnxt_qplib_cq_process_res_rc and bnxt_qplib_cq_process_res_ud and there
is no need to convert it again in bnxt_re_poll_cq. Modified the union to
hold the correct data type.
Fixes: 95b087f87b ("bnxt_re: Fix imm_data endianness")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730110014-20755-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
During reset, cmd to destroy resources such as qp, cq, and mr may fail,
and error logs will be printed. When a large number of resources are
destroyed, there will be lots of printings, and it may lead to a cpu
stuck.
Delete some unnecessary printings and replace other printing functions
in these paths with the ratelimited version.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Fixes: c7bcb13442 ("RDMA/hns: Add SRQ support for hip08 kernel mode")
Fixes: 70f9252158 ("RDMA/hns: Use the reserved loopback QPs to free MR before destroying MPT")
Fixes: 926a01dc00 ("RDMA/hns: Add QP operations support for hip08 SoC")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241024124000.2931869-6-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The hem code is executed before ib_dev is registered, so use dev_*
printing instead of ibdev_* to avoid log like this:
(null): set HEM address to HW failed!
Fixes: 2f49de21f3 ("RDMA/hns: Optimize mhop get flow for multi-hop addressing")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241024124000.2931869-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The sub-directory of hns_roce debugfs is named after the device's
kernel name currently, but it will be inconvenient to use when
the device is renamed.
Modify the name to pci name as users can always easily find the
correspondence between an RDMA device and its pci name.
Fixes: eb7854d63d ("RDMA/hns: Support SW stats with debugfs")
Signed-off-by: Yuyu Li <liyuyu6@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241024124000.2931869-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
QP needs to be modified to IB_QPS_ERROR to trigger HW flush cqe. But
when this process races with destroy qp, the destroy-qp process may
modify the QP to IB_QPS_RESET first. In this case flush cqe will fail
since it is invalid to modify qp from IB_QPS_RESET to IB_QPS_ERROR.
Add lock and bit flag to make sure pending flush cqe work is completed
first and no more new works will be added.
Fixes: ffd541d457 ("RDMA/hns: Add the workqueue framework for flush cqe handler")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241024124000.2931869-3-huangjunxian6@hisilicon.com
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
eq_db_ci is updated only after all AEQEs are processed in the AEQ
interrupt handler, which is not timely enough and may result in
AEQ overflow. Two optimization methods are proposed:
1. Set an upper limit for AEQE processing.
2. Move time-consuming operations such as printings to the bottom
half of the interrupt.
cmd events and flush_cqe events are still fully processed in the top half
to ensure timely handling.
Fixes: a5073d6054 ("RDMA/hns: Add eq support of hip08")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241024124000.2931869-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Access flag definition in MR and QP is different
in FW. Currently both reg/bind MR and modify/query QP uses
the same flags. Add a different function to map
the QP access flags for newer adapters.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1729065346-1364-6-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
RoCE message rate performance is heavily degraded
without the use of cq coalescing. With proper coalescing,
message rates get better. Furthermore, coalescing
significantly reduces contention on the PCIe Root
Complex/Memory subsystems.
Add the changes to configure CQ rx colascing parameters
based on adapter revision when CQ is created.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1729065346-1364-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Modify QP improvements are for state transitions
from INIT -> RTR and RTR -> RTS.
In order to support the Modify QP Optimization feature,
the driver is expected to check for the feature support
in the CMDQ_QUERY_FUNC and register its support for this
feature with the FW in CMDQ_INITIALIZE_FIRMWARE.
Additionally, the driver is required to specify the new
fields and attribute masks for the transitions as follows:
1. INIT -> RTR:
- New fields: srq_used, type.
- enable srq_used when RC QP is configured to use SRQ.
- set the type based on the QP type.
- Mandatory masks:
- RC: CMDQ_MODIFY_QP_MODIFY_MASK_ACCESS,
CMDQ_MODIFY_QP_MODIFY_MASK_PKEY
- UD QP and QP1: CMDQ_MODIFY_QP_MODIFY_MASK_PKEY,
CMDQ_MODIFY_QP_MODIFY_MASK_QKEY
2. RTR -> RTS:
- New fields: type
- set the type based on the QP type.
- Mandatory masks:
- RC: CMDQ_MODIFY_QP_MODIFY_MASK_ACCESS
- UD QP and QP1: CMDQ_MODIFY_QP_MODIFY_MASK_QKEY
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Tushar Rane <tushar.rane@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1729065346-1364-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Using modify QP with AH attributes and IB_QP_AV flag set doesn't make
much sense for connectionless QP types like SRD. Add SL parameter to EFA
create QP user ABI and pass it to the device.
Link: https://patch.msgid.link/r/20241015174242.3490-3-mrgolin@amazon.com
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Reviewed-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There is a race between the CREQ tasklet and destroy qp when accessing the
qp-handle table. There is a chance of reading a valid qp-handle in the
CREQ tasklet handler while the QP is already moving ahead with the
destruction.
Fixing this race by implementing a table-lock to synchronize the access.
Fixes: f218d67ef0 ("RDMA/bnxt_re: Allow posting when QPs are in error")
Fixes: 84cf229f40 ("RDMA/bnxt_re: Fix the qp table indexing")
Link: https://patch.msgid.link/r/1728912975-19346-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Control path completion processing always runs in tasklet context. To
synchronize with the posting thread, there is no need to use the irq
variant of spin lock. Use spin_lock_bh instead.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://patch.msgid.link/r/1728912975-19346-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
After the cited commit below max_dest_rd_atomic and max_rd_atomic values
are being rounded down to the next power of 2. As opposed to the old
behavior and mlx4 driver where they used to be rounded up instead.
In order to stay consistent with older code and other drivers, revert to
using fls round function which rounds up to the next power of 2.
Fixes: f18e26af6a ("RDMA/mlx5: Convert modify QP to use MLX5_SET macros")
Link: https://patch.msgid.link/r/d85515d6ef21a2fa8ef4c8293dce9b58df8a6297.1728550179.git.leon@kernel.org
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
GID table length is reported by FW. The gid index which is passed to the
driver during modify_qp/create_ah is restricted by the sgid_index field of
struct ib_global_route. sgid_index is u8 and the max sgid possible is
256.
Each GID entry in HW will have 2 GID entries in the kernel gid table. So
we can support twice the gid table size reported by FW. Also, restrict the
max GID to 256 also.
Fixes: 847b97887e ("RDMA/bnxt_re: Restrict the max_gids to 256")
Link: https://patch.msgid.link/r/1728373302-19530-11-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Avoid memory corruption while setting up Level-2 PBL pages for the non MR
resources when num_pages > 256K.
There will be a single PDE page address (contiguous pages in the case of >
PAGE_SIZE), but, current logic assumes multiple pages, leading to invalid
memory access after 256K PBL entries in the PDE.
Fixes: 0c4dcd6028 ("RDMA/bnxt_re: Refactor hardware queue memory allocation")
Link: https://patch.msgid.link/r/1728373302-19530-10-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently the CQ toggle value in the shared page (read by the userlib) is
updated as part of the cqn_handler. There is a potential race of
application calling the CQ ARM doorbell immediately and using the old
toggle value.
Change the sequence of updating CQ toggle value to update in the
bnxt_qplib_service_nq function immediately after reading the toggle value
to be in sync with the HW updated value.
Fixes: e275919d96 ("RDMA/bnxt_re: Share a page to expose per CQ info with userspace")
Link: https://patch.msgid.link/r/1728373302-19530-9-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In bnxt_re_add_device(), when register netdev notifier fails, driver is
not unregistering the IB device in the error cleanup path. Also, removed
the duplicate cleanup in error path of bnxt_re_probe.
Fixes: 94a9dc6ac8 ("RDMA/bnxt_re: Group all operations under add_device and remove_device")
Link: https://patch.msgid.link/r/1728373302-19530-8-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Driver waits indefinitely for the fifo occupancy to go below a threshold
as soon as the pacing interrupt is received. This can cause soft lockup on
one of the processors, if the rate of DB is very high.
Add a loop count for FPGA and exit the __wait_for_fifo_occupancy_below_th
if the loop is taking more time. Pacing will be continuing until the
occupancy is below the threshold. This is ensured by the checks in
bnxt_re_pacing_timer_exp and further scheduling the work for pacing based
on the fifo occupancy.
Fixes: 2ad4e6303a ("RDMA/bnxt_re: Implement doorbell pacing algorithm")
Link: https://patch.msgid.link/r/1728373302-19530-7-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When the HWRM command fails, driver currently returns -EFAULT(Bad
address). This does not look correct.
Modified to return -EIO(I/O error).
Fixes: cc1ec769b8 ("RDMA/bnxt_re: Fixing the Control path command and response handling")
Fixes: 65288a22dd ("RDMA/bnxt_re: use shadow qd while posting non blocking rcfw command")
Link: https://patch.msgid.link/r/1728373302-19530-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently driver is not getting correct srq. Dereference only if qplib has
a valid srq.
Fixes: b02fd3f79e ("RDMA/bnxt_re: Report async events and errors")
Link: https://patch.msgid.link/r/1728373302-19530-4-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Driver exports pacing stats only on GenP5 and P7 adapters. But while
parsing the pacing stats, driver has a check for "rdev->dbr_pacing". This
caused a trace when KASAN is enabled.
BUG: KASAN: slab-out-of-bounds in bnxt_re_get_hw_stats+0x2b6a/0x2e00 [bnxt_re]
Write of size 8 at addr ffff8885942a6340 by task modprobe/4809
Fixes: 8b6573ff34 ("bnxt_re: Update the debug counters for doorbell pacing")
Link: https://patch.msgid.link/r/1728373302-19530-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Older adapters doesn't support the MAX CQ WQEs reported by older FW. So
restrict the value reported to 1M always for older adapters.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://patch.msgid.link/r/1728373302-19530-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Abhishek Mohapatra<abhishek.mohapatra@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There is "accept*" misspelled as "accpet*" in the comments. Fix the
spelling.
Fixes: 146b9756f1 ("RDMA/irdma: Add connection manager")
Link: https://patch.msgid.link/r/20241008161913.19965-1-green@qrator.net
Signed-off-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
ip_dev_find() always returns real net_device address, whether traffic is
running on a vlan or real device, if traffic is over vlan, filling
endpoint struture with real ndev and an attempt to send a connect request
will results in RDMA_CM_EVENT_UNREACHABLE error. This patch fixes the
issue by using vlan_dev_real_dev().
Fixes: 830662f6f0 ("RDMA/cxgb4: Add support for active and passive open connection with IPv6 address")
Link: https://patch.msgid.link/r/20241007132311.70593-1-anumula@chelsio.com
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
clear_all_interrupts() in hw/hfi1/chip.c is currently global
but only used in the same file, so make it static.
There are also 'clear_all_interrupts' functions in i2c-nomadik and
emif.c but fortunately they're already static.
(Build and boot tested only, I don't have this hardware)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20241007235327.128613-1-linux@treblig.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
max_sw_wqe used for static wqe mode should be same as the max_wqe.
Calculate the max_sw_wqe only for the variable WQE mode.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Link: https://patch.msgid.link/r/1726715161-18941-7-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
__alloc_pbl() can return error when memory allocation fails.
Driver is not checking the status on one of the instances.
Fixes: 0c4dcd6028 ("RDMA/bnxt_re: Refactor hardware queue memory allocation")
Link: https://patch.msgid.link/r/1726715161-18941-4-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Driver uses internal data structure to construct WQE frame.
It used avid type as u16 which can accommodate up to 64K AVs.
When outstanding AVID crosses 64K, driver truncates AVID and
hence it uses incorrect AVID to WR. This leads to WR failure
due to invalid AV ID and QP is moved to error state with reason
set to 19 (INVALID AVID). When RDMA CM path is used, this issue
hits QP1 and it is moved to error state
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://patch.msgid.link/r/1726715161-18941-3-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In bnxt_re_setup_chip_ctx() when bnxt_qplib_map_db_bar() fails
driver is not freeing the memory allocated for "rdev->chip_ctx".
Fixes: 0ac20faf5d ("RDMA/bnxt_re: Reorg the bar mapping")
Link: https://patch.msgid.link/r/1726715161-18941-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When HW is being reset, userspace should not ring doorbell otherwise
it may lead to abnormal consequence such as RAS.
Disassociate mmap pages for all uctx to prevent userspace from ringing
doorbell to HW. Since all resources will be destroyed during HW reset,
no new mmap is allowed after HW reset is completed.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240927103323.1897094-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lookup_atid() function can return NULL if the ATID is
invalid or does not exist in the identifier table, which
could lead to dereferencing a null pointer without a
check in the `act_establish()` and `act_open_rpl()` functions.
Add a NULL check to prevent null pointer dereferencing.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Signed-off-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Link: https://patch.msgid.link/20240912145844.77516-1-m.lobanov@rosalinux.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
There are several error cases where hns_roce_create_ah() returns
directly without jumping to sw stat path, thus leading to a problem
that the ah error counter does not increase.
Fixes: ee20cc17e9 ("RDMA/hns: Support DSCP")
Fixes: eb7854d63d ("RDMA/hns: Support SW stats with debugfs")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240912115700.2016443-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
If the FW crashes, L2 driver gets notified and it notifies
the RoCE driver. Currently driver doesn't re-initialize the
device. Add support for re-initialize the RoCE device.
RoCE device is removed and re-attached in the ulp_stop and
ulp_start respectively. The recovery logic expects the RoCE
driver to be registered with L2 driver while its being removed.
So the driver avoids unregistering with L2 driver in the
recovery path.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1726027710-2292-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Adding and removing device need to be handled from multiple contexts
when Firmware error recovery is supported. So group all the add and remove
operations to add_device and remove_device function.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1726027710-2292-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
While registering with the L2 for ULP operations, use the
aux device pointer as the handle. Aux device has
the data bnxt_re_en_dev_info, which is used to
store required information for the bnxt_re_suspend
and bnxt_re_resume functions.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1726027710-2292-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
rdev will be destroyed and recreated during the FW error
recovery scenarios. So to keep the state, if any, use an
en_info structure which gets created/freed based on auxiliary
device initialization/de-initialization.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1726027710-2292-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The IB layer provides a common interface to store and get net
devices associated to an IB device port (ib_device_set_netdev()
and ib_device_get_netdev()).
Previously, mlx5_ib stored and managed the associated net devices
internally.
Replace internal net device management in mlx5_ib with
ib_device_set_netdev() when attaching/detaching a net device and
ib_device_get_netdev() when retrieving the net device.
Export ib_device_get_netdev().
For mlx5 representors/PFs/VFs and lag creation we replace the netdev
assignments with the IB set/get netdev functions.
In active-backup mode lag the active slave net device is stored in the
lag itself. To assure the net device stored in a lag bond IB device is
the active slave we implement the following:
- mlx5_core: when modifying the slave of a bond we send the internal driver event
MLX5_DRIVER_EVENT_ACTIVE_BACKUP_LAG_CHANGE_LOWERSTATE.
- mlx5_ib: when catching the event call ib_device_set_netdev()
This patch also ensures the correct IB events are sent in switchdev lag.
While at it, when in multiport eswitch mode, only a single IB device is
created for all ports. The said IB device will receive all netdev events
of its VFs once loaded, thus to avoid overwriting the mapping of PF IB
device to PF netdev, ignore NETDEV_REGISTER events if the ib device has
already been mapped to a netdev.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909173025.30422-6-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
phys_port_cnt of the IB device must be initialized before calling
ib_device_set_netdev().
Previously, phys_port_cnt was initialized in the mlx5_ib init function.
Remove this initialization to allow setting it separately, providing
the flexibility to call ib_device_set_netdev before registering the
IB device.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909173025.30422-4-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Report the upper device's state as the RDMA port state only in RoCE LAG or
switchdev LAG.
Fixes: 27f9e0ccb6 ("net/mlx5: Lag, Add single RDMA device in multiport mode")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909173025.30422-3-michaelgur@nvidia.com
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Check if RoCE LAG is active before calling the LAG layer for netdev.
This clarifies if LAG is active. No behavior changes with this patch.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909173025.30422-2-michaelgur@nvidia.com
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Consider also the query_vuid cap before enabling the data_direct
functionality.
This may prevent a syndrome from the FW in case the query_vuid command
is not supported. (e.g. migratable VF)
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Gal Shalom <galshalom@nvidia.com>
Link: https://patch.msgid.link/274c4f6f1ac0b1078243dd296695a49dbe58e7d1.1725907637.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implicit MRs in ODP memory scheme require allocating a private null mkey
and assigning the mkey and va differently in the KSM mkey.
The page faults are received on the null mkey so we also add storing the
null mkey in the odp_mkey xarray.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-8-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The memory scheme page fault event is a new approch in handling page fault
on mkeys using the on-demand-paging feature.
The major shift in handling the page fault in this scheme is that the HW
is taking responsibilty for parsing the faulted mkey instead of the
previous approach where the driver would read and parse the wqes and
query the mkeys to get to the direct mkey that we need to handle.
Therefore, the event we get from FW in this scheme will contain the
direct mkey and address we need to handle and require much less work
from driver.
Additionally, to optimize performance, the FW can generate the event on
a memory area that is larger than the faulted memory operation is
requiring, to 'prefetch' memory that is around it and will likely be
used soon.
Unlike previous types of page fault, the memory page scheme fault does
not always require a resume command after handling the page fault as the FW
can post multiple events on same mkey and will set the 'last' flag only on
the page fault that requires the resume command.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-7-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Split the search for the ODP mkey when handling an rdma type page fault to
a helper function, later to be used in other page fault types.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-6-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The new memory scheme page faults are requesting the driver to fetch
additinal pages to the faulted memory access.
This is done in order to prefetch pages before and after the area that
got the page fault, assuming this will reduce the total amount of page
faults.
The driver should ensure it handles only the pages that are within the
umem range.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-5-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add new fields to support the new memory scheme page fault and extend
the token field to u64 as in the new scheme the token is 48 bit.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-4-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Expose IFC bits to support the new memory scheme on demand paging.
Change the macro reading odp capabilities to be able to read from the
new IFC layout and align the code in upper layers to be compiled.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-3-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Protect the usage of the 6th bit with the relevant capability to ensure
we are using the new page sizes with FW that supports the bit extension.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-2-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The definition of qib_rc_rnr_retry() has been removed since
commit b4238e7057 ("IB/qib: Use new rdmavt timers"). Also, the definition
of mr_rcu_callback() has been remove since commit 7c2e11fe2d ("IB/qib:
Remove qp and mr functionality from qib"). So, let's remove the unused
declartions.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Link: https://patch.msgid.link/20240909121408.80079-3-zhangzekun11@huawei.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When allocating MTT hem, for each hop level of each hem that is being
allocated, the driver iterates the hem list to find out whether the
bt page has been allocated in this hop level. If not, allocate a new
one and splice it to the list. The time complexity is O(n^2) in worst
cases.
Currently the allocation for-loop uses 'unit' as the step size. This
actually has taken into account the reuse of last-hop-level MTT bt
pages by multiple buffer pages. Thus pages of last hop level will
never have been allocated, so there is no need to iterate the hem list
in last hop level.
Removing this unnecessary iteration can reduce the time complexity to
O(n).
Fixes: 38389eaa4d ("RDMA/hns: Add mtr support for mixed multihop addressing")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-9-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The 1bit-ECC recovery address read from HW only contain bits 64:12, so
it should be fixed left-shifted 12 bits when used.
Currently, the driver will shift the address left by PAGE_SHIFT when
used, which is wrong in non-4K OS.
Fixes: 2de949abd6 ("RDMA/hns: Recover 1bit-ECC error of RAM on chip")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In abnormal interrupt handler, a PF reset will be triggered even if
the device is a VF. It should be a VF reset.
Fixes: 2b9acb9a97 ("RDMA/hns: Add the process of AEQ overflow for hip08")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-7-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The max value of 'unit' and 'hop_num' is 2^24 and 2, so the value of
'step' may exceed the range of u32. Change the type of 'step' to u64.
Fixes: 38389eaa4d ("RDMA/hns: Add mtr support for mixed multihop addressing")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently rsv_qp is freed before ib_unregister_device() is called
on HIP08. During the time interval, users can still dereg MR and
rsv_qp will be used in this process, leading to a UAF. Move the
release of rsv_qp after calling ib_unregister_device() to fix it.
Fixes: 70f9252158 ("RDMA/hns: Use the reserved loopback QPs to free MR before destroying MPT")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The field 'rq next block addr' in QPC can be updated by driver only
on HIP08. On HIP09 HW updates this field while driver is not allowed.
Fixes: 926a01dc00 ("RDMA/hns: Add QP operations support for hip08 SoC")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20240906093444.3571619-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When variable size WQE is supported, max_qp_sges reported
is more than 6. For devices that supports variable size WQE,
the Send WQE size calculation is wrong when an an older library
that doesn't support variable size WQE is used.
Set the WQE size to 128 when static WQE is supported.
Fixes: de1d364c38 ("RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1725444253-13221-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
For older adapters that doesn't support variable size WQE,
driver is wrongly reporting that variable WQE is supported,
when the latest library is used.
Report the variable WQE capability only if the driver supports
it.
Fixes: 10a104c0de ("RDMA/bnxt_re: Enable variable size WQEs for user space applications")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1725444253-13221-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Fix the cleanup of the temp cache entries that are dynamically created
in the MR cache.
The cleanup of the temp cache entries is currently scheduled only when a
new entry is created. Since in the cleanup of the entries only the mkeys
are destroyed and the cache entry stays in the cache, subsequent
registrations might reuse the entry and it will eventually be filled with
new mkeys without cleanup ever getting scheduled again.
On workloads that register and deregister MRs with a wide range of
properties we see the cache ends up holding many cache entries, each
holding the max number of mkeys that were ever used through it.
Additionally, as the cleanup work is scheduled to run over the whole
cache, any mkey that is returned to the cache after the cleanup was
scheduled will be held for less than the intended 30 seconds timeout.
Solve both issues by dropping the existing remove_ent_work and reusing
the existing per-entry work to also handle the temp entries cleanup.
Schedule the work to run with a 30 seconds delay every time we push an
mkey to a clean temp entry.
This ensures the cleanup runs on each entry only 30 seconds after the
first mkey was pushed to an empty entry.
As we have already been distinguishing between persistent and temp entries
when scheduling the cache_work_func, it is not being scheduled in any
other flows for the temp entries.
Another benefit from moving to a per-entry cleanup is we now not
required to hold the rb_tree mutex, thus enabling other flow to run
concurrently.
Fixes: dd1b913fb0 ("RDMA/mlx5: Cache all user cacheable mkeys on dereg MR flow")
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/e4fa4bb03bebf20dceae320f26816cd2dde23a26.1725362530.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When searching the MR cache for suitable cache entries, don't use mkeys
larger than twice the size required for the MR.
This should ensure the usage of mkeys closer to the minimal required size
and reduce memory waste.
On driver init we create entries for mkeys with clear attributes and
powers of 2 sizes from 4 to the max supported size.
This solves the issue for anyone using mkeys that fit these
requirements.
In the use case where an MR is registered with different attributes,
like an access flag we can't UMR, we'll create a new cache entry to store
it upon dereg.
Without this fix, any later registration with same attributes and smaller
size will use the newly created cache entry and it's mkeys, disregarding
the memory waste of using mkeys larger than required.
For example, one worst-case scenario can be when registering and
deregistering a 1GB mkey with ATS enabled which will cause the creation of
a new cache entry to hold those type of mkeys. A user registering a 4k MR
with ATS will end up using the new cache entry and an mkey that can
support a 1GB MR, thus wasting x250k memory than actually needed in the HW.
Additionally, allow all small registration to use the smallest size
cache entry that is initialized on driver load even if size is larger
than twice the required size.
Fixes: 73d09b2fe8 ("RDMA/mlx5: Introduce mlx5r_cache_rb_key")
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/8ba3a6e3748aace2026de8b83da03aba084f78f4.1725362530.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
After an mkey is created, update the counter for pending mkeys before
reshceduling the work that is filling the cache.
Rescheduling the work with a full MR cache entry and a wrong 'pending'
counter will cause us to miss disabling the fill_to_high_water flag.
Thus leaving the cache full but with an indication that it's still
needs to be filled up to it's full size (2 * limit).
Next time an mkey will be taken from the cache, we'll unnecessarily
continue the process of filling the cache to it's full size.
Fixes: 57e7071683 ("RDMA/mlx5: Implement mkeys management via LIFO queue")
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/0f44f462ba22e45f72cb3d0ec6a748634086b8d0.1725362530.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The canceling of dealyed work in clean_keys() is a leftover from years
back and was added to prevent races in the cleanup process of MR cache.
The cleanup process was rewritten a few years ago and the canceling of
delayed work and flushing of workqueue was added before the call to
clean_keys().
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/943d21f5a9dba7b98a3e1d531e3561ffe9745d71.1725362530.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When creating kernel MRs, it is not definitive whether they will be used
for peer-to-peer transactions or for other usecases, since address
mapping is performed only after the MR is created.
Since peer-to-peer transactions benefit significantly from ATS
performance-wise, enable ATS on newly-allocated kernel MRs when
supported.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Gal Shalom <galshalom@nvidia.com>
Link: https://patch.msgid.link/fafd4c9f14cf438d2882d88649c2947e1d05d0b4.1725273403.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Some of the adapters support Relaxed Ordering for the MRs.
Driver queries support for Memory region relax ordering support from
firmware and set relax ordering bit in REGISTER_MR request, if the users
request for the support. Also, this is supported only if the PCIe device
has enabled relaxed ordering attribute.
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vijay Kumar Mandadapu <vijaykumar.mandadapu@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1725256351-12751-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Firmware now have a new mr registration command where
both MR allocation and registration can be done in a
single hwrm command. Driver has to issue this new hwrm
command whenever the support flag is set. This reduces
the number of hwrm issued per MR creation and speed up
the MR creation.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1725256351-12751-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Updating the HW structures for the pcie relax ordering support.
Newly added interface structures will be used in the
followup patch.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1725256351-12751-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Gen P7 adapters needs to share a toggle bits information received
in kernel driver with the user space. User space needs this
info to arm the SRQ.
User space application can get this page using the
UAPI routines. Library will mmap this page and get the
toggle bits to be used in the next ARM Doorbell.
Uses a hash list to map the SRQ structure from the SRQ ID.
SRQ structure is retrieved from the hash list while the
library calls the UAPI routine to get the toggle page
mapping. Currently the full page is mapped per SRQ. This
can be optimized to enable multiple SRQs from the same
application share the same page and different offsets
in the page
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1724945645-14989-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Refactor the code in this function to have common code.
This is used in subsequent patches.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1724945645-14989-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
SRQ arming requires the toggle bits received from hardware.
Get the toggle bits from SRQ notification for the
gen p7 adapters. This value will be zero for the older adapters.
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1724945645-14989-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Since commit be4c9bad9d ("MAINTAINERS: Add cxgb4 and iw_cxgb4 entries")
c4iw_post_terminate() declaration is not used anymore.
And other declarations were never implemented since introduction in
commit cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC").
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20240824091629.3659565-1-yuehaibing@huawei.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Selvin Xavier says:
=============
Enable the Variable size Work Queue entry support for Gen P7
adapters. This would help in the better utilization of the queue memory
and pci bandwidth due to the smaller send queue Work entries.
=============
Based on v6.11-rc5 for dependencies.
* bnxt_re_variable_wqes: (829 commits)
RDMA/bnxt_re: Enable variable size WQEs for user space applications
RDMA/bnxt_re: Handle variable WQE support for user applications
RDMA/bnxt_re: Fix the table size for PSN/MSN entries
RDMA/bnxt_re: Get the WQE index from slot index while completing the WQEs
RDMA/bnxt_re: Add support for Variable WQE in Genp7 adapters
Linux 6.11-rc5
...
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add backward compatibility code to enable variable size WQEs only if the
user lib supports it.
Link: https://patch.msgid.link/r/1724042847-1481-6-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
User library calculates the number of slots required for user applications
and it can pass that information to the driver. Driver can use this value
and update the HW directly. This mechanism is currently used only for the
newly introduced variable size WQEs.
Extend the bnxt_re_qp_req structure to pass the Send Queue slot count.
Reorganize the code to get the sq_slots before initializing the Send Queue
attributes.
Link: https://patch.msgid.link/r/1724042847-1481-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
HW MSN table size is always a power of 2. So the pages should be mapped
accordingly.
Use the power of two calculation while get the number of PSN/MSN entries.
Fixes: 6f6bfbc595 ("RDMA/bnxt_re: Expose the MSN table capability for user library")
Link: https://patch.msgid.link/r/1724042847-1481-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
While reporting the completions, SQ Work Queue index is required to
identify the WQE that generated the completions. In variable WQE mode, FW
returns the slot index for Error completions. Driver need to walk through
the shadow queue between the consumer index and producer index and matches
the slot index returned by FW. If a match is found, the next index of the
shadow queue is the WQE index to be considered for remaining poll_cq loop.
Link: https://patch.msgid.link/r/1724042847-1481-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Variable size WQE means that each send Work Queue Entry to HW can use
different WQE sizes as opposed to the static WQE size on the current
devices. Set variable WQE mode for Gen P7 devices. Depth of the Queue will
be a multiple of slot which is 16 bytes. The number of slots should be a
multiple of 256 as per the HW requirement.
Initialize the Software shadow queue to hold requests equal to the number
of slots. Also, do not expose the variable size WQE capability until the
last patch in the series.
Link: https://patch.msgid.link/r/1724042847-1481-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Propagate the unique, per device, ID in the device attributes to the
standard node_guid value in IB device.
Link: https://patch.msgid.link/r/20240822171143.2800-1-mrgolin@amazon.com
Reviewed-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Yehuda Yitschak <yehuday@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add support for DMABUF MR registrations with Data-direct device.
Upon userspace calling to register a DMABUF MR with the data direct bit
set, the below algorithm will be followed.
1) Obtain a pinned DMABUF umem from the IB core using the user input
parameters (FD, offset, length) and the DMA PF device. The DMA PF
device is needed to allow the IOMMU to enable the DMA PF to access the
user buffer over PCI.
2) Create a KSM MKEY by setting its entries according to the user buffer
VA to IOVA mapping, with the MKEY being the data direct device-crossed
MKEY. This KSM MKEY is umrable and will be used as part of the MR cache.
The PD for creating it is the internal device 'data direct' kernel one.
3) Create a crossing MKEY that points to the KSM MKEY using the crossing
access mode.
4) Manage the KSM MKEY by adding it to a list of 'data direct' MKEYs
managed on the mlx5_ib device.
5) Return the crossing MKEY to the user, created with its supplied PD.
Upon DMA PF unbind flow, the driver will revoke the KSM entries.
The final deregistration will occur under the hood once the application
deregisters its MKEY.
Notes:
- This version supports only the PINNED UMEM mode, so there is no
dependency on ODP.
- The IOVA supplied by the application must be system page aligned due to
HW translations of KSM.
- The crossing MKEY will not be umrable or part of the MR cache, as we
cannot change its crossed (i.e. KSM) MKEY over UMR.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/1f99d8020ed540d9702b9e2252a145a439609ba6.1722512548.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Pass uverbs_attr_bundle as part of '.reg_user_mr_dmabuf' API instead of
udata.
This enables passing some new ioctl attributes to the drivers, as will
be introduced in the next patches for mlx5 driver.
Change the involved drivers accordingly.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/9a25b2fc02443f7c36c2d93499ae25252b6afd40.1722512548.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add the NET device initialization flow to utilize the 'data
direct' device.
When a NET mlx5_ib device is capable of 'data direct', the following
sequence of actions will occur:
- Find its affiliated 'data direct' VUID via a firmware command.
- Create its own private PD and 'data direct' mkey.
- Register to be notified when its 'data direct' driver is probed or removed.
The DMA device of the affiliated 'data direct' device, including the
private PD and the 'data direct' mkey, will be used later during MR
registrations that request the data direct functionality.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/b11fa87b2a65bce4db8d40341bb6cee490fa4d06.1722512548.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Introduce the 'data direct' driver for a ConnectX-8 Data Direct device.
The 'data direct' driver functions as the affiliated DMA device for one
or more capable mlx5_ib devices. This DMA device, as the name suggests,
is used exclusively for DMA operations. It can be considered a DMA engine
managed by a PF/VF, lacking network capabilities and having minimal overall
capabilities.
Consequently, the DMA NIC PF will not be exposed to or directly used by
software applications. The driver will not have any direct interface or
interaction with the firmware (no command interface, no capabilities,
etc.). It will operate solely over PCI to enable its DMA functionality.
Registration and un-registration of the driver are handled as part of
the mlx5_ib initialization and exit processes, as the mlx5_ib devices
will effectively be its clients.
The driver will serve as the DMA device for accessing another PCI device
to achieve optimal performance (both on the same NUMA node, P2P access,
etc.).
Upon probing, it will read its VUID over PCI to handle mlx5_ib device
registrations with the same VUID.
Upon removal, it will notify its clients to allow them to clean up the
resources that were mmaped with its DMA device.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/b77edecfd476c3f445da96ab6aef499ae47b2829.1722512548.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In multiport mode, RDMA devices make it impossible for userspace to use
DEVX to discover vhca id values for ports beyond port 1. This patch
addresses the issue by exposing the vhca id of all ports.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://patch.msgid.link/41dea83aa51843aa4c067b4f73f28d64e51bd53c.1722331101.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
dma_alloc_coherent() allocates contiguous memory irrespective of
iommu mode, but after commit f5ff79fddf ("dma-mapping: remove CONFIG_DMA_REMAP")
if iommu is enabled in translate mode, dma_alloc_coherent() may
allocate non-contiguous memory. Attempt to map this memory results in panic.
This patch fixes the issue by using dma_mmap_coherent() to map each page
to user space.
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://lore.kernel.org/r/20240716142532.97423-1-anumula@chelsio.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
- Core:
* Support for the "ats-supported" device-tree property.
* Removal of the 'ops' field from 'struct iommu_fwspec'.
* Introduction of iommu_paging_domain_alloc() and partial conversion
of existing users.
* Introduce 'struct iommu_attach_handle' and provide corresponding
IOMMU interfaces which will be used by the IOMMUFD subsystem.
* Remove stale documentation.
* Add missing MODULE_DESCRIPTION() macro.
* Misc cleanups.
- Allwinner Sun50i:
* Ensure bypass mode is disabled on H616 SoCs.
* Ensure page-tables are allocated below 4GiB for the 32-bit
page-table walker.
* Add new device-tree compatible strings.
- AMD Vi:
* Use try_cmpxchg64() instead of cmpxchg64() when updating pte.
- Arm SMMUv2:
* Print much more useful information on context faults.
* Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n.
* Add new Qualcomm device-tree bindings.
- Arm SMMUv3:
* Support for hardware update of access/dirty bits and reporting via
IOMMUFD.
* More driver rework from Jason, this time updating the PASID/SVA support
to prepare for full IOMMUFD support.
* Add missing MODULE_DESCRIPTION() macro.
* Minor fixes and cleanups.
- NVIDIA Tegra:
* Fix for benign fwspec initialisation issue exposed by rework on the
core branch.
- Intel VT-d:
* Use try_cmpxchg64() instead of cmpxchg64() when updating pte.
* Use READ_ONCE() to read volatile descriptor status.
* Remove support for handling Execute-Requested requests.
* Avoid calling iommu_domain_alloc().
* Minor fixes and refactoring.
- Qualcomm MSM:
* Updates to the device-tree bindings.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmaZTqMQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNApdB/wL2gW7ANJN3KDrOiWdq06P9fuzxbuiAegI
aKGH+aT05kJjLBXpAE5K9Bas0RbgN8iIB4TITDR9jyLnMOlTP3poy0fvB8y27q00
/WkQ7yVPkZc58ySdEOGH/EbuQkiXcD1YTjTGWP9071xzbWTDbsYN0smfbvvB9LgI
56KhdcUtB0QsqhqBzyyznHJLFdpVvDpbkiAFDXJfor7SNOOtV9a4Ect6IYteaYKz
S6+DWDEfUs+fHTEKEZ9sZVA745f2zPkT/YHY8vjLOEukWN07+3/2AKTra19DIgqF
HCGitRyZjOut1fg8sLn0SUliCKe/G/bHlwSbHnxJQ73b91YDvpzD
=xvLD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Will Deacon:
"Core:
- Support for the "ats-supported" device-tree property
- Removal of the 'ops' field from 'struct iommu_fwspec'
- Introduction of iommu_paging_domain_alloc() and partial conversion
of existing users
- Introduce 'struct iommu_attach_handle' and provide corresponding
IOMMU interfaces which will be used by the IOMMUFD subsystem
- Remove stale documentation
- Add missing MODULE_DESCRIPTION() macro
- Misc cleanups
Allwinner Sun50i:
- Ensure bypass mode is disabled on H616 SoCs
- Ensure page-tables are allocated below 4GiB for the 32-bit
page-table walker
- Add new device-tree compatible strings
AMD Vi:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
Arm SMMUv2:
- Print much more useful information on context faults
- Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n
- Add new Qualcomm device-tree bindings
Arm SMMUv3:
- Support for hardware update of access/dirty bits and reporting via
IOMMUFD
- More driver rework from Jason, this time updating the PASID/SVA
support to prepare for full IOMMUFD support
- Add missing MODULE_DESCRIPTION() macro
- Minor fixes and cleanups
NVIDIA Tegra:
- Fix for benign fwspec initialisation issue exposed by rework on the
core branch
Intel VT-d:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
- Use READ_ONCE() to read volatile descriptor status
- Remove support for handling Execute-Requested requests
- Avoid calling iommu_domain_alloc()
- Minor fixes and refactoring
Qualcomm MSM:
- Updates to the device-tree bindings"
* tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (72 commits)
iommu/tegra-smmu: Pass correct fwnode to iommu_fwspec_init()
iommu/vt-d: Fix identity map bounds in si_domain_init()
iommu: Move IOMMU_DIRTY_NO_CLEAR define
dt-bindings: iommu: Convert msm,iommu-v0 to yaml
iommu/vt-d: Fix aligned pages in calculate_psi_aligned_address()
iommu/vt-d: Limit max address mask to MAX_AGAW_PFN_WIDTH
docs: iommu: Remove outdated Documentation/userspace-api/iommu.rst
arm64: dts: fvp: Enable PCIe ATS for Base RevC FVP
iommu/of: Support ats-supported device-tree property
dt-bindings: PCI: generic: Add ats-supported property
iommu: Remove iommu_fwspec ops
OF: Simplify of_iommu_configure()
ACPI: Retire acpi_iommu_fwspec_ops()
iommu: Resolve fwspec ops automatically
iommu/mediatek-v1: Clean up redundant fwspec checks
RDMA/usnic: Use iommu_paging_domain_alloc()
wifi: ath11k: Use iommu_paging_domain_alloc()
wifi: ath10k: Use iommu_paging_domain_alloc()
drm/msm: Use iommu_paging_domain_alloc()
vhost-vdpa: Use iommu_paging_domain_alloc()
...
Usual collection of small improvements and fixes:
- Bug fixes and minor improvments in efa, irdma, mlx4, mlx5, rxe, hf1,
qib, ocrdma
- bnxt_re support for MSN, which is a new retransmit logic
- Initial mana support for RC qps
- Use after free bug and cleanups in iwcm
- Reduce resource usage in mlx5 when RDMA verbs features are not used
- New verb to drain shared recieve queues, similar to normal recieve
queues. This is necessary to allow ULPs a clean shutdown. Used in the
iscsi rdma target
- mlx5 support for more than 16 bits of doorbell indexes
- Doorbell moderation support for bnxt_re
- IB multi-plane support for mlx5
- New EFA adaptor PCI IDs
- RDMA_NAME_ASSIGN_TYPE_USER to hint to userspace that it shouldn't rename
the device
- A collection of hns bugs
- Fix long standing bug in bnxt_re with incorrect endian handling of
immediate data
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZpfvKQAKCRCFwuHvBreF
YXomAP46gZpGv5mlMOAXePRuKq6glNZWl3pVuwuycnlmjQcEUQD/dhQbJz0rZKBr
swuibPo83bFacfXJL7Wxd48m4G3EfgI=
=1eXu
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Usual collection of small improvements and fixes:
- Bug fixes and minor improvments in efa, irdma, mlx4, mlx5, rxe,
hf1, qib, ocrdma
- bnxt_re support for MSN, which is a new retransmit logic
- Initial mana support for RC qps
- Use after free bug and cleanups in iwcm
- Reduce resource usage in mlx5 when RDMA verbs features are not used
- New verb to drain shared recieve queues, similar to normal recieve
queues. This is necessary to allow ULPs a clean shutdown. Used in
the iscsi rdma target
- mlx5 support for more than 16 bits of doorbell indexes
- Doorbell moderation support for bnxt_re
- IB multi-plane support for mlx5
- New EFA adaptor PCI IDs
- RDMA_NAME_ASSIGN_TYPE_USER to hint to userspace that it shouldn't
rename the device
- A collection of hns bugs
- Fix long standing bug in bnxt_re with incorrect endian handling of
immediate data"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (65 commits)
IB/hfi1: Constify struct flag_table
RDMA/mana_ib: Set correct device into ib
bnxt_re: Fix imm_data endianness
RDMA: Fix netdev tracker in ib_device_set_netdev
RDMA/hns: Fix mbx timing out before CMD execution is completed
RDMA/hns: Fix insufficient extend DB for VFs.
RDMA/hns: Fix undifined behavior caused by invalid max_sge
RDMA/hns: Fix shift-out-bounds when max_inline_data is 0
RDMA/hns: Fix missing pagesize and alignment check in FRMR
RDMA/hns: Fix unmatch exception handling when init eq table fails
RDMA/hns: Fix soft lockup under heavy CEQE load
RDMA/hns: Check atomic wr length
RDMA/ocrdma: Don't inline statistics functions
RDMA/core: Introduce "name_assign_type" for an IB device
RDMA/qib: Fix truncation compilation warnings in qib_verbs.c
RDMA/qib: Fix truncation compilation warnings in qib_init.c
RDMA/efa: Add EFA 0xefa3 PCI ID
RDMA/mlx5: Support per-plane port IB counters by querying PPCNT register
net/mlx5: mlx5_ifc update for accessing ppcnt register of plane ports
RDMA/mlx5: Add plane index support when querying PTYS registers
...
Shay Says:
==========
Introduce auxiliary bus IRQs sysfs
Today, PCI PFs and VFs, which are anchored on the PCI bus, display their
IRQ information in the <pci_device>/msi_irqs/<irq_num> sysfs files. PCI
subfunctions (SFs) are similar to PFs and VFs and these SFs are anchored
on the auxiliary bus. However, these PCI SFs lack such IRQ information
on the auxiliary bus, leaving users without visibility into which IRQs
are used by the SFs. This absence makes it impossible to debug
situations and to understand the source of interrupts/SFs for
performance tuning and debug.
Additionally, the SFs are multifunctional devices supporting RDMA,
network devices, clocks, and more, similar to their peer PCI PFs and
VFs. Therefore, it is desirable to have SFs' IRQ information available
at the bus/device level.
To overcome the above limitations, this short series extends the
auxiliary bus to display IRQ information in sysfs, similar to that of
PFs and VFs.
It adds an 'irqs' directory under the auxiliary device and includes an
<irq_num> sysfs file within it.
For example:
$ ls /sys/bus/auxiliary/devices/mlx5_core.sf.1/irqs/
50 51 52 53 54 55 56 57 58
Patch summary:
patch-1 adds auxiliary bus to support irqs used by auxiliary device
patch-2 mlx5 driver using exposing irqs for PCI SF devices via auxiliary
bus
==========
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmaQTCYACgkQSD+KveBX
+j7nRAgAhyi8mD93AjpoXX8onbK3ZyPnGwLToCs0NT3EzT0BIwNvDovQp4rhcs16
3zVwvW+twVsbMuPYTpPVgcynpL6N0K/CoW+ubDGZaRIaf0nDmh4MY1wY/EUsVj8R
FbeTi5L+9MyKvFbtO5d4cW1q7M0XVD3uR8Wle6PwvXZ1gcM59vsR1eml25NLTC8B
Z9F9WKG+dFAni0ll/IL837Se3QQapRXtJQ3g6XbIcpXiMqgIrHZ9FyY0LvuWlQq4
LsIPKh7RySATmAYXwwpsnfdrilvvMHsyjlAoeNHEJBsAUY+kpOIFFi6J5EB+/oyo
jhBhlc4Al0vUXis9jGTysO7mVYVOUQ==
=DTxS
-----END PGP SIGNATURE-----
Merge tag 'aux-sysfs-irqs' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
aux-sysfs-irqs
Shay Says:
==========
Introduce auxiliary bus IRQs sysfs
Today, PCI PFs and VFs, which are anchored on the PCI bus, display their
IRQ information in the <pci_device>/msi_irqs/<irq_num> sysfs files. PCI
subfunctions (SFs) are similar to PFs and VFs and these SFs are anchored
on the auxiliary bus. However, these PCI SFs lack such IRQ information
on the auxiliary bus, leaving users without visibility into which IRQs
are used by the SFs. This absence makes it impossible to debug
situations and to understand the source of interrupts/SFs for
performance tuning and debug.
Additionally, the SFs are multifunctional devices supporting RDMA,
network devices, clocks, and more, similar to their peer PCI PFs and
VFs. Therefore, it is desirable to have SFs' IRQ information available
at the bus/device level.
To overcome the above limitations, this short series extends the
auxiliary bus to display IRQ information in sysfs, similar to that of
PFs and VFs.
It adds an 'irqs' directory under the auxiliary device and includes an
<irq_num> sysfs file within it.
For example:
$ ls /sys/bus/auxiliary/devices/mlx5_core.sf.1/irqs/
50 51 52 53 54 55 56 57 58
Patch summary:
patch-1 adds auxiliary bus to support irqs used by auxiliary device
patch-2 mlx5 driver using exposing irqs for PCI SF devices via auxiliary
bus
==========
* tag 'aux-sysfs-irqs' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Expose SFs IRQs
driver core: auxiliary bus: show auxiliary device IRQs
RDMA/mlx5: Add Qcounters req_transport_retries_exceeded/req_rnr_retries_exceeded
net/mlx5: Reimplement write combining test
====================
Link: https://patch.msgid.link/20240711213140.256997-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'struct flag_table' are not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
302932 40271 112 343315 53d13 drivers/infiniband/hw/hfi1/chip.o
After:
=====
text data bss dec hex filename
311636 31567 112 343315 53d13 drivers/infiniband/hw/hfi1/chip.o
Link: https://lore.kernel.org/r/782b6a648bfbbf2bb83f81a73c0460b5bb7642a1.1720959310.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add mana_get_primary_netdev_rcu helper to get a primary
netdevice for a given port. When mana is used with
netvsc, the VF netdev is controlled by an upper netvsc
device. In a baremetal case, the VF netdev is the
primary device.
Use the mana_get_primary_netdev_rcu() helper in the mana_ib
to get the correct device for querying network states.
Fixes: 8b184e4f1c ("RDMA/mana_ib: Enable RoCE on port 1")
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://lore.kernel.org/r/1720705077-322-1-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When map a device between servers with MLX and BCM RoCE nics, RTRS
server complain about unknown imm type, and can't map the device,
After more debug, it seems bnxt_re wrongly handle the
imm_data, this patch fixed the compat issue with MLX for us.
In off list discussion, Selvin confirmed HW is working in little endian format
and all data needs to be converted to LE while providing.
This patch fix the endianness for imm_data
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20240710122102.37569-1-jinpu.wang@ionos.com
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When a large number of tasks are issued, the speed of HW processing
mbx will slow down. The standard for judging mbx timeout in the current
firmware is 30ms, and the current timeout standard for the driver is also
30ms.
Considering that firmware scheduling in multi-function scenarios takes a
certain amount of time, this will cause the driver to time out too early
and report a failure before mbx execution times out.
This patch introduces a new mechanism that can set different timeouts for
different cmds and extends the timeout of mbx to 35ms.
Fixes: a04ff739f2 ("RDMA/hns: Add command queue support for hip08 RoCE driver")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-9-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
VFs and its PF will share the memory of the extend DB. Currently,
the number of extend DB allocated by driver is only enough for PF.
This leads to a probability of DB loss and some other problems in
scenarios where both PF and VFs use a large number of QPs.
Fixes: 6b63597d35 ("RDMA/hns: Add TSQ link table support")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
If max_sge has been set to 0, roundup_pow_of_two() in
set_srq_basic_param() may have undefined behavior.
Fixes: 9dd052474a ("RDMA/hns: Allocate one more recv SGE for HIP08")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-7-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The offset requires 128B alignment and the page size ranges from
4K to 128M.
Fixes: 68a997c5d2 ("RDMA/hns: Add FRMR support for hip08")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
CEQEs are handled in interrupt handler currently. This may cause the
CPU core staying in interrupt context too long and lead to soft lockup
under heavy load.
Handle CEQEs in BH workqueue and set an upper limit for the number of
CEQE handled by a single call of work handler.
Fixes: a5073d6054 ("RDMA/hns: Add eq support of hip08")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
8 bytes is the only supported length of atomic. Add this check in
set_rc_wqe(). Besides, stop processing WQEs and return from
set_rc_wqe() if there is any error.
Fixes: 384f881851 ("RDMA/hns: Add atomic support")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240710133705.896445-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Fix the problem of KASAN causing the stack frame size to increase
drivers/infiniband/hw/ocrdma/ocrdma_stats.c:686:16: error: stack frame size (20664) exceeds limit (8192) in 'ocrdma_dbgfs_ops_read' [-Werror,-Wframe-larger-than]
static ssize_t ocrdma_dbgfs_ops_read(struct file *filp, char __user *buffer,
^
Some functions called by ocrdma_dbgfs_ops_read occupy a lot of stack space.
Mark these functions as noinline_for_stack to prevent them from accumulating
in ocrdma_dbgfs_ops_read.
Signed-off-by: Peng Hao <flyingpeng@tencent.com>
Link: https://lore.kernel.org/r/20240710091657.26291-1-flyingpeng@tencent.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
usnic_uiom_alloc_pd() allocates a paging domain for a given device.
In this case, iommu_domain_alloc(dev->bus) is equivalent to
iommu_paging_domain_alloc(dev). Replace it as iommu_domain_alloc()
has been deprecated.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240610085555.88197-15-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
The name_assign_type indicates how the name is provided. Currently
these types are supported:
- RDMA_NAME_ASSIGN_TYPE_UNKNOWN: Unknown or not set;
- RDMA_NAME_ASSIGN_TYPE_USER: Name is provided by the user; The
user-created sub device, rxe and siw device has this type.
When filling nl device info, it is set in the new attribute
RDMA_NLDEV_ATTR_NAME_ASSIGN_TYPE. User-space tools like udev
"rdma_rename" could check this attribute to determine if this
device needs to be renamed or not.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/522591bef9a369cc8e5dcb77787e017bffee37fe.1719837610.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reduce nodename string size to fit IB_DEVICE_NODE_DESC_MAX.
drivers/infiniband/hw/qib/qib_verbs.c: In function ‘qib_register_ib_device’:
drivers/infiniband/hw/qib/qib_verbs.c:1554:40: error: ‘%s’ directive output may be truncated writing up to 64 bytes into a region of size 43
[-Werror=format-truncation=]
1554 | "Intel Infiniband HCA %s", init_utsname()->nodename);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/qib/qib_verbs.c:1553:9: note: ‘snprintf’ output between 22 and 86 bytes into a destination of size 64
1553 | snprintf(ibdev->node_desc, sizeof(ibdev->node_desc),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1554 | "Intel Infiniband HCA %s", init_utsname()->nodename);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Link: https://lore.kernel.org/r/1fb6393fa2e0702fef995834c3c7db972bbc4d06.1719837715.git.leon@kernel.org
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
drivers/infiniband/hw/qib/qib_init.c: In function ‘qib_init_one’:
drivers/infiniband/hw/qib/qib_init.c:586:67: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size between 0 and 3 [-Werror=format-truncation=]
586 | snprintf(wq_name, sizeof(wq_name), "qib%d_%d",
| ^~
In function ‘qib_create_workqueues’,
inlined from ‘qib_init_one’ at drivers/infiniband/hw/qib/qib_init.c:1438:8:
drivers/infiniband/hw/qib/qib_init.c:586:60: note: directive argument in the range [-2147483643, 254]
586 | snprintf(wq_name, sizeof(wq_name), "qib%d_%d",
| ^~~~~~~~~~
drivers/infiniband/hw/qib/qib_init.c:586:25: note: ‘snprintf’ output between 7 and 27 bytes into a destination of size 8
586 | snprintf(wq_name, sizeof(wq_name), "qib%d_%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
587 | dd->unit, pidx);
| ~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Link: https://lore.kernel.org/r/ab5222c414a01e9d2c5129ef26836aace9ee2aa5.1719837715.git.leon@kernel.org
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
This patch supports driver APIs "add_sub_dev" and "del_sub_dev", to
add and delete a plane device respectively.
A mlx5 plane device is a rdma SMI device; It provides the SMI capability
through user MAD for it's parent, the logical multi-plane aggregated
device. For a plane port:
- It supports QP0 only;
- When adding a plane device, all plane ports are added;
- For some commands like mad_ifc, both plane_index and native portnum
is needed;
- When querying or modifying a plane port context, the native portnum
must be used, as the query/modify_hca_vport_context command doesn't
support plane port.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/e933cd0562aece181f8657af2ca0f5b387d0f14e.1718553901.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
When multi-plane is supported, a logical port, which is aggregation of
multiple physical plane ports, is exposed for data transmission.
Compared with a normal mlx5 IB port, this logical port supports all
functionalities except Subnet Management.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/7e37c06c9cb243be9ac79930cd17053903785b95.1718553901.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
If the HW register read fails, the FIFO will be always shown as
full. DB moderation doesn't work in that case and the traffic fails.
So disable this feature and log a message.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1719456065-27394-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Enable DB moderation support for GenP7 adapters also. Query from FW
and update the status.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1719456065-27394-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
GenP5 and P7 devices have different DB FIFO depth. Use different
values based on the chip context.
Instead of hardcoding doorbell FIFO related values, get it
from the HWRM interface. Maintain backward compatibility
by having default values when FW is not providing the doorbell
FIFO related values.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1719456065-27394-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add UAR page index as a driver ioctl attribute to increase the number of
supported indices, previously limited to 16 bits by mlx5_ib_create_cq
struct.
Link: https://lore.kernel.org/r/0e18b34d7ec3b1ae02d694b0d545aed7413c0ef7.1719512393.git.leon@kernel.org
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Changes the create_cq verb signature by sending the entire uverbs attr
bundle as a parameter. This allows drivers to send driver specific attrs
through ioctl for the create_cq verb and access them in their driver
specific code.
Also adds a new enum value for driver specific ioctl attributes for
methods already supporting UHW.
Link: https://lore.kernel.org/r/ed147343987c0d43fd391c1b2f85e2f425747387.1719512393.git.leon@kernel.org
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have the same macro in main and verbs files and we don't use the macro
in the verbs file, remove it.
Link: https://lore.kernel.org/r/20240624160918.27060-3-mrgolin@amazon.com
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Reviewed-by: Gal Pressman <gal.pressman@linux.dev>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use offset_in_page() instead of open-coding it.
Link: https://lore.kernel.org/r/20240624160918.27060-2-mrgolin@amazon.com
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
'struct mmu_rb_ops' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
10879 164 0 11043 2b23 drivers/infiniband/hw/hfi1/pin_system.o
After:
=====
text data bss dec hex filename
10907 140 0 11047 2b27 drivers/infiniband/hw/hfi1/pin_system.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b826dd05eefa5f4d6a7a1b4d191eaf37c714ed04.1719259997.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
drivers/infiniband/hw/mlx4/alias_GUID.c: In function ‘mlx4_ib_init_alias_guid_service’:
drivers/infiniband/hw/mlx4/alias_GUID.c:878:74: error: ‘%d’ directive
output may be truncated writing between 1 and 11 bytes into a region of
size 5 [-Werror=format-truncation=]
878 | snprintf(alias_wq_name, sizeof alias_wq_name, "alias_guid%d", i);
| ^~
drivers/infiniband/hw/mlx4/alias_GUID.c:878:63: note: directive argument in the range [-2147483641, 2147483646]
878 | snprintf(alias_wq_name, sizeof alias_wq_name, "alias_guid%d", i);
| ^~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/alias_GUID.c:878:17: note: ‘snprintf’ output
between 12 and 22 bytes into a destination of size 15
878 | snprintf(alias_wq_name, sizeof alias_wq_name, "alias_guid%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: a0c64a17ab ("mlx4: Add alias_guid mechanism")
Link: https://lore.kernel.org/r/1951c9500109ca7e36dcd523f8a5f2d0d2a608d1.1718554641.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Increase size of the name array to avoid truncated output warning.
drivers/infiniband/hw/mlx4/mad.c: In function ‘mlx4_ib_alloc_demux_ctx’:
drivers/infiniband/hw/mlx4/mad.c:2197:47: error: ‘%d’ directive output
may be truncated writing between 1 and 11 bytes into a region of size 4
[-Werror=format-truncation=]
2197 | snprintf(name, sizeof(name), "mlx4_ibt%d", port);
| ^~
drivers/infiniband/hw/mlx4/mad.c:2197:38: note: directive argument in
the range [-2147483645, 2147483647]
2197 | snprintf(name, sizeof(name), "mlx4_ibt%d", port);
| ^~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:2197:9: note: ‘snprintf’ output between
10 and 20 bytes into a destination of size 12
2197 | snprintf(name, sizeof(name), "mlx4_ibt%d", port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:2205:48: error: ‘%d’ directive output
may be truncated writing between 1 and 11 bytes into a region of size 3
[-Werror=format-truncation=]
2205 | snprintf(name, sizeof(name), "mlx4_ibwi%d", port);
| ^~
drivers/infiniband/hw/mlx4/mad.c:2205:38: note: directive argument in
the range [-2147483645, 2147483647]
2205 | snprintf(name, sizeof(name), "mlx4_ibwi%d", port);
| ^~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:2205:9: note: ‘snprintf’ output between
11 and 21 bytes into a destination of size 12
2205 | snprintf(name, sizeof(name), "mlx4_ibwi%d", port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:2213:48: error: ‘%d’ directive output
may be truncated writing between 1 and 11 bytes into a region of size 3
[-Werror=format-truncation=]
2213 | snprintf(name, sizeof(name), "mlx4_ibud%d", port);
| ^~
drivers/infiniband/hw/mlx4/mad.c:2213:38: note: directive argument in
the range [-2147483645, 2147483647]
2213 | snprintf(name, sizeof(name), "mlx4_ibud%d", port);
| ^~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:2213:9: note: ‘snprintf’ output between
11 and 21 bytes into a destination of size 12
2213 | snprintf(name, sizeof(name), "mlx4_ibud%d", port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:244: drivers/infiniband/hw/mlx4/mad.o] Error 1
Fixes: fc06573dfa ("IB/mlx4: Initialize SR-IOV IB support for slaves in master context")
Link: https://lore.kernel.org/r/f3798b3ce9a410257d7e1ec7c9e285f1352e256a.1718554569.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
max_sge attribute is passed by the user, and is inserted and used
unchecked, so verify that the value doesn't exceed maximum allowed value
before using it.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://lore.kernel.org/r/277ccc29e8d57bfd53ddeb2ac633f2760cf8cdd0.1716900410.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
