Some BH1750 sensors require a hardware reset before they can be
detected on the I2C bus. This implementation adds support for an
optional reset GPIO that can be specified in the device tree.
The reset sequence pulls the GPIO low and then high before initializing
the sensor, which enables proper detection with tools like i2cdetect.
This is particularly important for sensors that power on in an
undefined state.
Signed-off-by: Sergio Perez <sergio@pereznus.es>
Link: https://patch.msgid.link/20250324135920.6802-2-sergio@pereznus.es
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On Intel platforms, the HID_USAGE_SENSOR_HUMAN_PROXIMITY report size is 16
bits. This patch adds support for handling 16-bit report sizes for the
HID_USAGE_SENSOR_HUMAN_PROXIMITY usage in the HID sensor proximity driver.
Previously, the driver only supported 8-bit and 32-bit report sizes. With
this change, the driver can now correctly process 16-bit proximity data,
ensuring accurate human presence detection on platforms where this report
size is used.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20250317013634.4117399-1-lixu.zhang@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The OFFSET calculation in the prox_read_raw() was incorrectly using the
unit exponent, which is intended for SCALE calculations.
Remove the incorrect OFFSET calculation and set it to a fixed value of 0.
Cc: stable@vger.kernel.org
Fixes: 39a3a0138f ("iio: hid-sensors: Added Proximity Sensor Driver")
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20250331055022.1149736-4-lixu.zhang@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the introduction of multi-channel support in commit 596ef5cf65
("iio: hid-sensor-prox: Add support for more channels"), each channel
requires an independent SCALE calculation, but the existing code only
calculates SCALE for a single channel.
Addresses the problem by modifying the driver to perform independent
SCALE calculations for each channel.
Cc: stable@vger.kernel.org
Fixes: 596ef5cf65 ("iio: hid-sensor-prox: Add support for more channels")
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20250331055022.1149736-3-lixu.zhang@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The threaded IRQ function in this driver is reading the flag twice: once to
lock a mutex and once to unlock it. Even though the code setting the flag
is designed to prevent it, there are subtle cases where the flag could be
true at the mutex_lock stage and false at the mutex_unlock stage. This
results in the mutex not being unlocked, resulting in a deadlock.
Fix it by making the opt3001_irq() code generally more robust, reading the
flag into a variable and using the variable value at both stages.
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20250321-opt3001-irq-fix-v1-1-6c520d851562@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The usual mixture of new drivers, support in existing drivers for new
devices, a range of features and general subsystem cleanup.
Two merges of immutable branches in here:
* SPI offload support. Culmination of a long effort to bring the ability
to offload triggered sequences of SPI operations to specific hardware,
allow high datarate acquisition over an SPI bus (if you have the right
hardware / FPGA firmware)
* GPIO set-array-helper - enables code simplification.
New device support
==================
adi,ad3552r-hs:
- Add support for AD3541r and AD3542r via newly supported FPGA HDL.
adi,ad4030
- New driver supporting the AD4030, AD4630 AD4630-16, AD4640-24, AD4632-16,
AD4632-24 1 and 2 channel high precision SPI ADCs.
adi,ad4851
- New driver and backend support for the AD4851, AD4852, AD4853, AD4854,
AD4855, AD4846, AD4857, AD4858 and AD4858I high speed multichannel
simultaneous sampling ADCs.
adi,ad7191
- New driver for this 24-bit ADC for precision bridge applications,
adi,ad7380
- Add support for the adaq4381-4 which is a 14-bit version of the
already supported adaq4380-1
adi,adis16550
- New driver using the ADIS library (which needed extensions) for this
IMU.
brcm,apds9160
- New driver for this proximity and ambient light sensor.
dynaimage,al3000a
- New driver for this illuminance sensor.
mcube,mc3230
- Add support for the mc3510c accelerometer with a different scale to existing
supported parts (some rework preceded this)
nxp,imx93
- Add compatibles for imx94 and imx95 which are fully compatible with imx93.
rockchip,saradc
- Add support for the RK3528 ADC
- Add support for the RK3562 ADC
silab,si7210
- New driver to support this I2C Hall effect magnetic position sensor.
ti,ads7138
- New driver supporting the ADS7128 and AD7138 I2C ADCs.
Staging driver drop
===================
adi,adis16240
- Drop this impact sensor. Interesting part but complex hence never left
staging due to ABI challenges. No longer readily available so drop driver.
New features
============
Documentation
- A really nice overview document introduce ADC terminology and how
it maps to IIO.
core
- New description for FAULT events, used in the ad7173.
- filter_type ABI used in ad4130.
buffer-dmaengine
- Split DMA channel request from buffer allocation (for SPI offload)
- Add a new _with_handle setup variant. (for SPI offload)
adi,adf4371
- Add control of reference clock type and support for frequency doubling
where appropriate.
adi,ad4695
- Support SPI offload.
- Support oversampling control.
adi,ad5791
- Support SPI offload.
adi,ad7124
- Add channel calibration support.
adi,ad7380:
- Alert support (threshold interrupts)
- SPI offload support.
adi,ad7606
- Support writing registers when using backend enabling software control
of modes.
adi,ad7944
- Support SPI offload.
adi,ad9832
- Use devm_regulator_get_enable() to simplify code.
adi,ad9834
- Use devm_regulator_get_enable() to simplify code.
adi,adxl345
- Improve IRQ handling code.
- Add debug access to registers.
bosch,bmi270
- Add temperature channel support.
- Add data ready trigger.
google,cross_ec
- Add trace events.
mcube,mc3230
- Add mount matrix support
- Add an OF match table.
Cleanup and minor bug fixes
===========================
Tree wide:
- Stop using iio_device_claim_direct_scoped() and introduce sparse friendly
iio_device_claim/release_direct()
The conditional scoped cleanup has proved hard to deal with, requiring
workarounds for various compiler issues and in is rather non-intuitive
so abandon that experiment. One of the attractions of that approach was
that it made it much harder to have unbalanced claim/release bugs so
instead introduce a conditional-lock style boolean returning new pair
of functions. These are inline in the header and have __acquire and
__release calls allowing sparse to detect lack of balance. There are
occasional false positives but so far those have reflected complex code
paths that benefited from cleanup anyway.
The first set of driver conversions are in this pull request, more to
follow next cycle. Various related cleanup in drivers.
Removal of the _scoped code is completed and the definition removed.
- Use of str_enable_disable() and similar helpers.
- Don't set regmap cache to REGCACHE_NONE as that's the default anyway.
- Change some caches from RBTREE to MAPLE reflecting best practice.
- Use the new gpiod_multi_set_value_cansleep()
- Make sure to grab direct mode for some calibrations paths.
- Avoid using memcmp on structures when checking for matching channel configs.
Instead just match field by field.
dt-bindings:
- Fix up indentation inconsistencies.
gts-helper:
- Simplify building of available scale table.
adi,ad-sigma-delta
- Make sure to disable channel after calibration done.
- Add error handling in configuring channel during calibration.
adi,ad2s1201
- use a bitmap_write() rather than directly accessing underlying storage.
adi,ad3552r-hs
- Fix a wrong error message.
- Make sure to use instruction mode for configuration.
adi,ad4695
- Add a conversion to ensure exit from conversion mode.
- Use custom regmap to handle required sclk rate change.
- Fix an out of bounds array access
- Simplify oversampling ratio handling.
adi,ad4851
- Fix a sign bug.
adi,ad5791
- Fix wrong exported number of storage bits.
adi,ad7124
- Disable all channels at probe to avoid strange initial configurations.
adi,ad7173
- Rework to allow static const struct ad_sigma_delta without need
to make a copy.
adi,ad7623
- Drop a BSD license tag that the authors consider unnecessary.
adi,ad7768-1
- Fix channels sign description exposed to user space.
- Set MOSI idle state to avoid accidental device reset.
- Avoid some overkill locking.
adi,axi-dac
- Check if device interface is busy when enabling data stream.
- Add control of bus mode.
bosch,bmi270
- Move a struct definition to a c file as only used there.
vishay,veml6030
- Enable regmap cache to reduce bus traffic.
- Fix ABI bug around scale reporting.
vishay,vem6075
- Check array bounds to harden against broken hardware.
Various other minor tweaks and fixes not called out.
*
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmfTNbkRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Foi41Q/+NTlPu1e9TqOqhXmpJc56EP5wnBaKuxMF
pgPjKr1bbh6Th131kdeCjcTtUyMeLoLLPzcmSzPVVBOLanTHw9d5DQutg7+k0yUE
8L0FEGEuSJeN6u6hnCFyKhOgu2xSPsCj1L99UCCsfXrvkUILSQgXSzoUkZDonmWj
gDd/Zfn1Otxevxct9KG4dHhiy17f734Oxhjv3xyMwHWsUtHndAJiYeYRzRxjMJTh
GeZHZMYvhnseLagAzfp3Dsqc5UCwm/Kmstz8wTlDW0kq/wbZqPwVLiC2xhPnTeds
PqAL3m/n7Z1SYBa5ouKZYcn2pMfcYNsd3ZfbFMIX0gecGZZ6zRfSgulVDZKe7tp+
cFbGhsIVWHt4TLWBevz6xihhyv/8ashi0PfIE1Gju8GZqqwwyR6wmdKJ1CNq3DmL
W9+74w7xAbN+Fg9C/EbuSk/+uKXFrdf9w1NtpnPzKWVwnR0tFwavgpxRCJpu9xMn
63nO/NCl+FtxibBBrpsTAb03hA4Fw595kiBBvkNSoNOYmoASj+w/bHhIFohZeteP
pS3eAQlMRCH4ZCjRDNHIEwO9xoja5aqprhnGCNrVQYR+OCfUw5ELf6GwYpEsmvtt
GyzgR92qxFBQz71h1/VyvAjxcaNRezO92VJajj+T2iJvj5lD6o/0+cscYWfEWEzn
dxuaXrpF3ak=
=4tID
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.15a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New device support, features and cleanup for the 6.15 cycle.
The usual mixture of new drivers, support in existing drivers for new
devices, a range of features and general subsystem cleanup.
Two merges of immutable branches in here:
* SPI offload support. Culmination of a long effort to bring the ability
to offload triggered sequences of SPI operations to specific hardware,
allow high datarate acquisition over an SPI bus (if you have the right
hardware / FPGA firmware)
* GPIO set-array-helper - enables code simplification.
New device support
==================
adi,ad3552r-hs:
- Add support for AD3541r and AD3542r via newly supported FPGA HDL.
adi,ad4030
- New driver supporting the AD4030, AD4630 AD4630-16, AD4640-24, AD4632-16,
AD4632-24 1 and 2 channel high precision SPI ADCs.
adi,ad4851
- New driver and backend support for the AD4851, AD4852, AD4853, AD4854,
AD4855, AD4846, AD4857, AD4858 and AD4858I high speed multichannel
simultaneous sampling ADCs.
adi,ad7191
- New driver for this 24-bit ADC for precision bridge applications,
adi,ad7380
- Add support for the adaq4381-4 which is a 14-bit version of the
already supported adaq4380-1
adi,adis16550
- New driver using the ADIS library (which needed extensions) for this
IMU.
brcm,apds9160
- New driver for this proximity and ambient light sensor.
dynaimage,al3000a
- New driver for this illuminance sensor.
mcube,mc3230
- Add support for the mc3510c accelerometer with a different scale to existing
supported parts (some rework preceded this)
nxp,imx93
- Add compatibles for imx94 and imx95 which are fully compatible with imx93.
rockchip,saradc
- Add support for the RK3528 ADC
- Add support for the RK3562 ADC
silab,si7210
- New driver to support this I2C Hall effect magnetic position sensor.
ti,ads7138
- New driver supporting the ADS7128 and AD7138 I2C ADCs.
Staging driver drop
===================
adi,adis16240
- Drop this impact sensor. Interesting part but complex hence never left
staging due to ABI challenges. No longer readily available so drop driver.
New features
============
Documentation
- A really nice overview document introduce ADC terminology and how
it maps to IIO.
core
- New description for FAULT events, used in the ad7173.
- filter_type ABI used in ad4130.
buffer-dmaengine
- Split DMA channel request from buffer allocation (for SPI offload)
- Add a new _with_handle setup variant. (for SPI offload)
adi,adf4371
- Add control of reference clock type and support for frequency doubling
where appropriate.
adi,ad4695
- Support SPI offload.
- Support oversampling control.
adi,ad5791
- Support SPI offload.
adi,ad7124
- Add channel calibration support.
adi,ad7380:
- Alert support (threshold interrupts)
- SPI offload support.
adi,ad7606
- Support writing registers when using backend enabling software control
of modes.
adi,ad7944
- Support SPI offload.
adi,ad9832
- Use devm_regulator_get_enable() to simplify code.
adi,ad9834
- Use devm_regulator_get_enable() to simplify code.
adi,adxl345
- Improve IRQ handling code.
- Add debug access to registers.
bosch,bmi270
- Add temperature channel support.
- Add data ready trigger.
google,cross_ec
- Add trace events.
mcube,mc3230
- Add mount matrix support
- Add an OF match table.
Cleanup and minor bug fixes
===========================
Tree wide:
- Stop using iio_device_claim_direct_scoped() and introduce sparse friendly
iio_device_claim/release_direct()
The conditional scoped cleanup has proved hard to deal with, requiring
workarounds for various compiler issues and in is rather non-intuitive
so abandon that experiment. One of the attractions of that approach was
that it made it much harder to have unbalanced claim/release bugs so
instead introduce a conditional-lock style boolean returning new pair
of functions. These are inline in the header and have __acquire and
__release calls allowing sparse to detect lack of balance. There are
occasional false positives but so far those have reflected complex code
paths that benefited from cleanup anyway.
The first set of driver conversions are in this pull request, more to
follow next cycle. Various related cleanup in drivers.
Removal of the _scoped code is completed and the definition removed.
- Use of str_enable_disable() and similar helpers.
- Don't set regmap cache to REGCACHE_NONE as that's the default anyway.
- Change some caches from RBTREE to MAPLE reflecting best practice.
- Use the new gpiod_multi_set_value_cansleep()
- Make sure to grab direct mode for some calibrations paths.
- Avoid using memcmp on structures when checking for matching channel configs.
Instead just match field by field.
dt-bindings:
- Fix up indentation inconsistencies.
gts-helper:
- Simplify building of available scale table.
adi,ad-sigma-delta
- Make sure to disable channel after calibration done.
- Add error handling in configuring channel during calibration.
adi,ad2s1201
- use a bitmap_write() rather than directly accessing underlying storage.
adi,ad3552r-hs
- Fix a wrong error message.
- Make sure to use instruction mode for configuration.
adi,ad4695
- Add a conversion to ensure exit from conversion mode.
- Use custom regmap to handle required sclk rate change.
- Fix an out of bounds array access
- Simplify oversampling ratio handling.
adi,ad4851
- Fix a sign bug.
adi,ad5791
- Fix wrong exported number of storage bits.
adi,ad7124
- Disable all channels at probe to avoid strange initial configurations.
adi,ad7173
- Rework to allow static const struct ad_sigma_delta without need
to make a copy.
adi,ad7623
- Drop a BSD license tag that the authors consider unnecessary.
adi,ad7768-1
- Fix channels sign description exposed to user space.
- Set MOSI idle state to avoid accidental device reset.
- Avoid some overkill locking.
adi,axi-dac
- Check if device interface is busy when enabling data stream.
- Add control of bus mode.
bosch,bmi270
- Move a struct definition to a c file as only used there.
vishay,veml6030
- Enable regmap cache to reduce bus traffic.
- Fix ABI bug around scale reporting.
vishay,vem6075
- Check array bounds to harden against broken hardware.
Various other minor tweaks and fixes not called out.
*
* tag 'iio-for-6.15a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (223 commits)
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
iio: adc: ad7124: Implement system calibration
iio: adc: ad7124: Implement internal calibration at probe time
iio: adc: ad_sigma_delta: Add error checking for ad_sigma_delta_set_channel()
iio: adc: ad4130: Adapt internal names to match official filter_type ABI
iio: adc: ad7173: Fix comparison of channel configs
iio: adc: ad7124: Fix comparison of channel configs
iio: adc: ad4130: Fix comparison of channel setups
...
The array contains only 5 elements, but the index calculated by
veml6075_read_int_time_index can range from 0 to 7,
which could lead to out-of-bounds access. The check prevents this issue.
Coverity Issue
CID 1574309: (#1 of 1): Out-of-bounds read (OVERRUN)
overrun-local: Overrunning array veml6075_it_ms of 5 4-byte
elements at element index 7 (byte offset 31) using
index int_index (which evaluates to 7)
This is hardening against potentially broken hardware. Good to have
but not necessary to backport.
Fixes: 3b82f43238 ("iio: light: add VEML6075 UVA and UVB light sensor driver")
Signed-off-by: Karan Sanghavi <karansanghvi98@gmail.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/Z7dnrEpKQdRZ2qFU@Emma
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AL3000a is a simple I2C-based ambient light sensor, which is
closely related to AL3010 and AL3320a, but has significantly
different way of processing data generated by the sensor.
Tested-by: Robert Eckelmann <longnoserob@gmail.com>
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250217140336.107476-3-clamor95@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Reviewed-by: Mudit Sharma <muditsharma.info@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250209180624.701140-27-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
REGCACHE_NONE is the default type of the cache when not provided.
Drop unneeded explicit assignment to it.
Note, it's defined to 0, and if ever be redefined, it will break
literally a lot of the drivers, so it very unlikely to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250129152546.1798306-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current scale is not ABI-compliant as it is just the sensor gain
instead of the value that acts as a multiplier to be applied to the raw
value (there is no offset).
Use the iio-gts helpers to obtain the proper scale values according to
the gain and integration time to match the resolution tables from the
datasheet and drop dedicated variables to store the current values of
the integration time, gain and resolution. When at it, use 'scale'
instead of 'gain' consistently for the get/set functions to avoid
misunderstandings.
Fixes: 7b779f573c ("iio: light: add driver for veml6030 ambient light sensor")
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20250127-veml6030-scale-v3-2-4f32ba03df94@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
APDS9160 is a combination of ALS and proximity sensors.
This patch add supports for:
- Intensity clear data and illuminance data
- Proximity data
- Gain control, rate control
- Event thresholds
Signed-off-by: Mikael Gonella-Bolduc <mgonellabolduc@dimonoff.com>
Link: https://patch.msgid.link/20250122-apds9160-driver-v5-2-5393be10279a@dimonoff.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The configuration registers are not volatile and are not affected
by read operations (i.e. not precious), making them suitable to be
cached in order to reduce the number of accesses to the device.
Add support for caching (RBTREE type).
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20250119-veml6030-scale-v2-2-6bfc4062a371@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for regfields as well to simplify register operations,
taking into account the different fields for the veml6030/veml7700 and
veml6035.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20250119-veml6030-scale-v2-1-6bfc4062a371@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the driver was originally created, it was decided that
sampling_frequency and hysteresis would be shared_per_type instead
of shared_by_all (even though it is internally shared by all). Eg:
in_proximity_raw
in_proximity_sampling_frequency
When we introduced support for more channels, we continued with
shared_by_type which. Eg:
in_proximity0_raw
in_proximity1_raw
in_proximity_sampling_frequency
in_attention_raw
in_attention_sampling_frequency
Ideally we should change to shared_by_all, but it is not an option,
because the current naming has been a stablished ABI by now. Luckily we
can use separate instead. That will be more consistent:
in_proximity0_raw
in_proximity0_sampling_frequency
in_proximity1_raw
in_proximity1_sampling_frequency
in_attention_raw
in_attention_sampling_frequency
Fixes: 596ef5cf65 ("iio: hid-sensor-prox: Add support for more channels")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-hid-sensor-v2-1-ff8c1959ec4a@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The two provided max_scale_nano values must be multiplied by 100 and 10
respectively to achieve nano units. According to the comments:
Max scale for apds0306 is 16.326432 → the fractional part is 0.326432,
which is 326432000 in NANO. The current value is 3264320.
Max scale for apds0306-065 is 14.09721 → the fractional part is 0.09712,
which is 97120000 in NANO. The current value is 9712000.
Update max_scale_nano initialization to use the right NANO fractional
parts.
Cc: stable@vger.kernel.org
Fixes: 620d1e6c7a ("iio: light: Add support for APDS9306 Light Sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Tested-by: subhajit.ghosh@tweaklogic.com
Link: https://patch.msgid.link/20250112-apds9306_nano_vals-v1-1-82fb145d0b16@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Given timing so late in cycle and that they are all confined to
specific drivers, it is fine for these to go upstream early in the
6.14 cycle.
hid-sensors
- Handle processed attention channel rather than just returning
an error.
adi,ad3552r
- Fix output ranges for ad3541r and ad3542r.
- Clear the reset status flag so that we can pick up any resets
during operation.
adi,ad5791
- Fix a misleading dt binding example where the sense of the
interrupt was reversed.
adi,ad7606
- Fix some hard coded offsets that should be taking the number of
channels on a particular part into account. These were missed
due to some racing changes.
ams,as73211
- Fix an off by one in optimized path for just reading the colour
channels.
bosch,bme680
- Fix type of variable passed as pointer, ensuring it works on
big endian systems and doesn't expose uninitialized data.
-----BEGIN PGP SIGNATURE-----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=J9mF
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Merge from Jonathan:
IIO: 2nd set of fixes for the 6.13 cycle.
Given timing so late in cycle and that they are all confined to
specific drivers, it is fine for these to go upstream early in the
6.14 cycle.
hid-sensors
- Handle processed attention channel rather than just returning
an error.
adi,ad3552r
- Fix output ranges for ad3541r and ad3542r.
- Clear the reset status flag so that we can pick up any resets
during operation.
adi,ad5791
- Fix a misleading dt binding example where the sense of the
interrupt was reversed.
adi,ad7606
- Fix some hard coded offsets that should be taking the number of
channels on a particular part into account. These were missed
due to some racing changes.
ams,as73211
- Fix an off by one in optimized path for just reading the colour
channels.
bosch,bme680
- Fix type of variable passed as pointer, ensuring it works on
big endian systems and doesn't expose uninitialized data.
* tag 'iio-fixes-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: dac: ad3552r-hs: clear reset status flag
iio: dac: ad3552r-common: fix ad3541/2r ranges
iio: chemical: bme680: Fix uninitialized variable in __bme680_read_raw()
iio: light: as73211: fix channel handling in only-color triggered buffer
dt-bindings: iio: dac: ad5791: ldac gpio is active low
iio: hid-sensor-prox: Fix invalid read_raw for attention
iio: adc: ad7606: Fix hardcoded offset in the ADC channels
We need the IIO fixes in here as well, and it resolves a merge conflict
in:
drivers/iio/adc/ti-ads1119.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current scale is not ABI-compliant as it is just the sensor gain
instead of the value that acts as a multiplier to be applied to the raw
value (there is no offset).
Use the iio-gts helpers to obtain the proper scale values according to
the gain and integration time to match the resolution tables from the
datasheet. When at it, use 'scale' instead of 'gain' consistently for
the get/set functions to avoid misunderstandings.
Fixes: c5a23f80c1 ("iio: light: add support for veml3235")
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241230-veml3235_scale-v3-2-48a5795e2f64@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The configuration and ID registers are not volatile and are not affected
by read operations (i.e. not precious), making them suitable to be
cached in order to reduce the number of accesses to the device.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241224-veml3235_scale-v2-3-2e1286846c77@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-By: Matti Vaittinen <mazziesaccount@gmail.com> #For bu27034, rpr0521
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channel index is off by one unit if AS73211_SCAN_MASK_ALL is not
set (optimized path for color channel readings), and it must be shifted
instead of leaving an empty channel for the temperature when it is off.
Once the channel index is fixed, the uninitialized channel must be set
to zero to avoid pushing uninitialized data.
Add available_scan_masks for all channels and only-color channels to let
the IIO core demux and repack the enabled channels.
Cc: stable@vger.kernel.org
Fixes: 403e5586b5 ("iio: light: as73211: New driver")
Tested-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241214-iio_memset_scan_holes-v4-1-260b395b8ed5@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The attention channel is a IIO_CHAN_INFO_PROCESSED, not a
IIO_CHAN_INFO_RAW.
Modify prox_read_raw() to support it.
Fixes: 596ef5cf65 ("iio: hid-sensor-prox: Add support for more channels")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20241122-fix-processed-v2-1-b9f606d3b519@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All devices supported by this driver (currently veml6030, veml6035
and veml7700) have two 16-bit channels, and can profit for the same
configuration to support data access via triggered buffers.
The measurements are stored in two 16-bit consecutive registers
(addresses 0x04 and 0x05) as little endian, unsigned data.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241124-veml6030_triggered_buffer-v3-1-565bb6b4b5c8@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BU27008 and BU27010 RGB sensors got cancelled. I was informed
they never reached mass production stage.
Keeping the drivers around is waste of maintenance resources. Drop the
drivers.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/f4d0aa31f29f160a06cba4856a034fa5636d3372.1732819203.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet, the chip requires a reset before any data
can be read. This commit moves the device identification logic to
occur after the reset to ensure proper initialization.
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Cibil Pankiras <cibil.pankiras@aerq.com>
Link: https://patch.msgid.link/20241114091323.7415-1-cibil.pankiras@aerq.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BU27034 uses mutex for protecting the gain / time / scale changes.
The clean-up for a few of the functions can be slightly simplified by
removing the goto-based error handling/unlocking and by utilizing the
guard(mutex) scoped mutex handling instead.
Simplify driver by using the scoped mutexes.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/4e65a4725c211b166906f70fdb5ba90f2af0f570.1732193263.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 'buffer' local array is used to push data to userspace from a
triggered buffer, but it does not set an initial value for the single
data element, which is an u16 aligned to 8 bytes. That leaves at least
4 bytes uninitialized even after writing an integer value with
regmap_read().
Initialize the array to zero before using it to avoid pushing
uninitialized information to userspace.
Cc: stable@vger.kernel.org
Fixes: ec90b52c07 ("iio: light: vcnl4035: Fix buffer alignment in iio_push_to_buffers_with_timestamp()")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241125-iio_memset_scan_holes-v1-6-0cb6e98d895c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 'scan' local struct is used to push data to user space from a
triggered buffer, but it does not set values for inactive channels, as
it only uses iio_for_each_active_channel() to assign new values.
Initialize the struct to zero before using it to avoid pushing
uninitialized information to userspace.
Cc: stable@vger.kernel.org
Fixes: eab35358aa ("iio: light: ROHM BH1745 colour sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241125-iio_memset_scan_holes-v1-7-0cb6e98d895c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the write_event_config callback now uses a bool for the state
parameter, update apds9300_set_intr_state accordingly and change intr_en
to bool.
Also update apds9300_set_power_state and power_state for consistency.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-12-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
write_event_config callback use an int for state, but it is actually a
boolean. iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to write_event_config.
Fix signature and update all iio drivers to use the new signature.
This patch has been partially written using coccinelle with the
following script:
$ cat iio-bool.cocci
// Options: --all-includes
virtual patch
@c1@
identifier iioinfo;
identifier wecfunc;
@@
static const struct iio_info iioinfo = {
...,
.write_event_config =
(
wecfunc
|
&wecfunc
),
...,
};
@@
identifier c1.wecfunc;
identifier indio_dev, chan, type, dir, state;
@@
int wecfunc(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, enum iio_event_type type, enum iio_event_direction dir,
-int
+bool
state) {
...
}
make coccicheck MODE=patch COCCI=iio-bool.cocci M=drivers/iio
Unfortunately, this script didn't match all files:
* all write_event_config callbacks using iio_device_claim_direct_scoped
were not detected and not patched.
* all files that do not assign and declare the write_event_config
callback in the same file.
iio.h was also manually updated.
The patch was build tested using allmodconfig config.
cc: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-7-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
state parameter is currently an int, but it is actually a boolean.
iio_ev_state_store is actually using kstrtobool to check user input,
then gives the converted boolean value to write_event_config. The code
in adux1020_write_event_config re-uses state parameter to store an
integer value. To prepare for updating the write_event_config signature
to use a boolean for state, introduce a new local int variable.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-6-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-3-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-1-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Egis620 supports 3 channels: presense, proximity and attention.
Modify the driver so it can read those channels as well.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241101-hpd-v3-5-e9c80b7c7164@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We are going to introduce more proximity channels. Make proximity a
indexed channel now, in a simple patch, so the change can be easily
bisected if there are any issues.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241101-hpd-v3-4-e9c80b7c7164@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The integration time of the veml6070 depends on an external resistor
(called Rset in the datasheet) and the value configured in the IT
field of the command register, whose supported values are 1/2x, 1x,
2x and 4x.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241031-veml6070-integration-time-v4-2-c66da6788256@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Vishay veml3235 is a low-power ambient light sensor with I2C
interface. It provides a minimum detectable intensity of
0.0021 lx/cnt, configurable integration time and gain, and an additional
white channel to distinguish between different light sources.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241023-veml3235-v3-2-8490f2622f9a@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241024-iio-fix-write-event-config-signature-v1-6-7d29e5a31b00@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://patch.msgid.link/20241024-iio-fix-write-event-config-signature-v1-5-7d29e5a31b00@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241024-iio-fix-write-event-config-signature-v1-4-7d29e5a31b00@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241024-iio-fix-write-event-config-signature-v1-3-7d29e5a31b00@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to the write_event_config
callback.
Remove useless code in write_event_config callback.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241024-iio-fix-write-event-config-signature-v1-1-7d29e5a31b00@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO core (ACPI part) provides a generic helper that may be used in
the driver. Replace a variant of iio_get_acpi_device_name_and_data().
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241024191200.229894-25-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commits in question do not proove that ACPI IDs exist.
Quite likely it was a cargo cult addition while doing that
for DT-based enumeration. Drop most likely fake ACPI IDs.
The to be removed IDs has been checked against the following resources:
1) DuckDuckGo
2) Google
3) MS catalog: https://www.catalog.update.microsoft.com/Search.aspx
This gives no useful results in regard to DSDT, moreover, the official
vendor ID in the registry for Lite-On is LCI.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241024191200.229894-23-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The complexity of config guards needed for ACPI_PTR() is not worthwhile
for the small amount of saved data. This example was doing it correctly
but I am proposing dropping this so as to reduce chance of cut and paste
where it is done wrong. Also drop now unneeded linux/acpi.h include and
added linux/mod_devicetable.h for struct acpi_device_id definition.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241024191200.229894-22-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO core (ACPI part) provides a generic helper that may be used in
the driver. Replace a variant of iio_get_acpi_device_name_and_data().
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241024191200.229894-21-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
TI's opt3002 light sensor shares most properties with the opt3001
model, with the exception of supporting a wider spectrum range.
Add support for TI's opt3002 by extending the TI opt3001 driver.
Datasheet: https://www.ti.com/product/OPT3002
Signed-off-by: Emil Gedenryd <emil.gedenryd@axis.com>
Link: https://patch.msgid.link/20241003-add_opt3002-v4-2-c550dc4591b4@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The raw value conversion to obtain a measurement in lux as
INT_PLUS_MICRO does not calculate the decimal part properly to display
it as micro (in this case microlux). It only calculates the module to
obtain the decimal part from a resolution that is 10000 times the
provided in the datasheet (0.5376 lux/cnt for the veml6030). The
resulting value must still be multiplied by 100 to make it micro.
This bug was introduced with the original implementation of the driver.
Only the illuminance channel is fixed becuase the scale is non sensical
for the intensity channels anyway.
Cc: stable@vger.kernel.org
Fixes: 7b779f573c ("iio: light: add driver for veml6030 ambient light sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241016-veml6030-fix-processed-micro-v1-1-4a5644796437@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define the integration time within the configuration register as a field
to easy its handling as an index, preparing the driver to support
configurable integration times.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241017-veml6070-integration-time-v1-2-3507d17d562a@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The custom rpr0521_trigger_consumer_store_time() is registered as trigger
handler in the devm_iio_triggered_buffer_setup() function. This function
is called from the calling of the iio_trigger_poll() used in the
sysfs/hrt triggers and it is not used anywhere else in this driver.
The irq handler of the driver is the rpr0521_drdy_irq_handler() which
saves the timestamp and then wakes the irq thread. The irq thread is
the rpr0521_drdy_irq_thread() function which checks if the irq came
from the sensor and wakes up the trigger threaded handler through
iio_trigger_poll_nested() or returns IRQ_NONE in case the irq didn't
come from this sensor.
This means that in the current driver, you can't reach the
rpr0521_trigger_consumer_store_time() when the device's irq is
triggered. This means that the extra check of iio_trigger_using_own()
is redundant since it will always be false so the general
iio_pollfunc_store_time() can be used.
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://patch.msgid.link/20240922162041.525896-2-vassilisamir@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for getting continuous readings from vl6180 using
triggered buffer approach. The continuous mode can be enabled by enabling
the buffer. Also added a trigger and appropriate checks to see that it is
used with this device.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20241007152223.59008-4-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupts are serviced in the `vl6180_measure` function when the
irq_handler signals that the reading is complete. We now can read
asynchronously if `client->irq` is set.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20241007152223.59008-3-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Expose the IIO_CHAN_INFO_SAMP_FREQ attribute as a way to configure the
inter-measurement period for both the IIO_DISTANCE and IIO_LIGHT
channels. The inter-measurement period must be given in milihertz.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20241007152223.59008-2-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The veml7700 contains the same sensor as the veml6030 in a different
package with no interrupt line and no pin to select the I2C address.
To handle the lack of the interrupt line and profit from the existing
support for the veml6030, add a specific iio_chan_spec with no
(num_)event_spec(s), and register the device's info from the
veml6030_info_no_irq struct.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241007-veml7700-v1-3-fb85dd839d63@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_info is identical for veml6030 and veml6035. Moreover,
veml6035_info_no_irq is missing the initialization of the read_avail
member, which is actually a bug if no irq is provided.
Instead of adding the missing initialization, remove the device-specific
iio_info and use the existing one for the veml6030.
Fixes: ccc26bd7d7 ("iio: light: veml6030: add support for veml6035")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241007-veml7700-v1-1-fb85dd839d63@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Most of this pull request is the result of Javier Carrasco doing a
careful audit for missing Kconfig dependencies that luck has meant
the random builds have never hit. The rest is the usual mix of old
bugs that have surfaced and some fallout from the recent merge window.
adi,ad5686
- Fix binding duplication of compatible strings.
bosch,bma400
- Fix an uninitialized variable in the event tap handling.
bosch,bmi323
- Fix several issues in the register saving and restore on suspend/resume
sensiron,spd500
- Fix missing CRC8 dependency
ti,op3001
- Fix a missing full-scale range value (values above this point were
all reported wrongly)
vishay,veml6030
- Fix a segmentation fault due to some type confusion.
- Fix wrong ambient light sensor resolution.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmcKj/oRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Foixog//XmU8jXEmkR236fViMBSJSY7mOAEwnZuh
LEOY8BDujHiu7XU+iz+DkXCXURaniENv50BHlK8z0OkukynaYLSmPmffwx2WG02Z
kXYl/9F9vWvqKZXms5fGJGy44b4sHXTsB+BBXHi8GB4ia5J/y6xN/561vVngw1Bg
ZsnZcvw/lq+XrGySOsYcMh7zsem+SrEBK4lLhhyXumxWwYKkplu9u9JZZZ6Z3uEq
A5BhdShNGYWu1wXqJ7t7VxhGzgpIUmF65aG+LyL/dx+2aMd3umZN92qYg9cea2b2
5Pu3JVer9uFL20c9zBTcpxcPADJLMWwuHq0LxFIawiLAyHySZUN4MJ4DCrhHI0KR
C+RUJCiXvl0cKKgd6VAtLLyvmQfdOXUbfa2BCiw+fE7CkbdCNM7WRI5cnkMDfa9p
3EghQBwmF721GHXccq/YdfrDF5Jd9TKViYQjGCljJvQeieAdGbcYTuL7yI/u3eng
CU2QhZ2kQo7bk4u1WcG6KFHonQT2IKLWwzq+dst7Npg4zgram6ciCbRRKZsGlmIm
lOybHMYsTju7fbqQ45Ka3EUzWHNfzF4EOZY4sbVKA1Hg1kzRmeR9qOdr9NAiH00r
Z19xa6Ef9w6zckhiw8L1OCdw70XEX2jMpzdsabYKkmDiZivUJHpA0GSPr9PV74qe
iWYt3V3+hgE=
=xo8X
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.12a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
IIO: 1st set of fixes for the 6.12 cycle.
Most of this pull request is the result of Javier Carrasco doing a
careful audit for missing Kconfig dependencies that luck has meant
the random builds have never hit. The rest is the usual mix of old
bugs that have surfaced and some fallout from the recent merge window.
adi,ad5686
- Fix binding duplication of compatible strings.
bosch,bma400
- Fix an uninitialized variable in the event tap handling.
bosch,bmi323
- Fix several issues in the register saving and restore on suspend/resume
sensiron,spd500
- Fix missing CRC8 dependency
ti,op3001
- Fix a missing full-scale range value (values above this point were
all reported wrongly)
vishay,veml6030
- Fix a segmentation fault due to some type confusion.
- Fix wrong ambient light sensor resolution.
* tag 'iio-fixes-for-6.12a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (34 commits)
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: magnetometer: af8133j: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: light: bu27008: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: chemical: ens160: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad5766: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad3552r: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmcDD/seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNpoH/3oEXaHBl5wrRJKP
GpzfT35Do052IZnRl0dmanr92opV5O7R4esVyHIS4IOKkt7C2aEEoVrMKAqW/VH9
EkcLPJwOuJ1xyqnLWycQUEN/JK9hxM9DlAVUVg9JdbDE4b91ebwTivwJMTJ7tQwm
+P/ifzV1r4fsYgpasqwVQMwLWuZ8O6OCGXE4KlgwiaS5zLdiVG+zkvvli/x/YHQ9
dPgQ+OXyoQz57Iwj02ZHBkdqJxa9vPVPASjtzuRp0v7VGaMq8gvVH8pA4B7cGjfV
xWvT+sjYjXVltYfmUHgUDNNTfeJArxH+BqpJ+lShcYwjxomYFfJWT0KZOPQwg/3z
zfAZtk4=
=RHAh
-----END PGP SIGNATURE-----
Merge tag 'v6.12-rc2' into test2
Linux 6.12-rc2
Resolved movement of asm/unaligned.h to linux/unaligned.h
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/iio/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241009060056.502059-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: 41ff93d14f ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-10-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The veml6035 is an ALS that shares most of its functionality with the
veml6030, which allows for some code recycling.
Some chip-specific properties differ and dedicated functions to get and
set the sensor gain as well as its initialization are required.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-9-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move devm_add_action_or_reset() with a device shut down action to the
hardware initialization function to ensure that any error path after
powering on the device leads to a power off. Add struct device *dev
to the argument list to clarify the device the action is registered
against, and use it wherever &client->dev was used.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-7-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The resolution of the WHITE channel is not provided by the manufacturer,
neither in the datasheet nor in the application note (even their
proprietary application only processes the ALS channel, giving raw
values for WHITE).
The current implementation assumes that both resolutions are identical,
which is extremely unlikely, especially for photodiodes with different
spectral responses.
Drop the processed information as it is meaningless.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-6-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop custom attributes by using the standard read_avail() callback to
read scale and integration time. When at it, add the integration time
and scale attributes fro the WHITE channel, as they modify its value as
well. To avoid breaking the current ABI, these attributes must be kept
as separate for both channels even though they are shared under the
hood.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-5-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the device managed function from the regulator API to get and enable
a regulator powering the device.
Use "vdd" as the ID to account for the provided name in the datasheet.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-4-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the more convenient dev_err_probe() to get rid of the dev_err() +
return sequence in the probe error paths.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-2-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The veml6030 requires a delay of 4 ms after activating the sensor. That
is done correctly during the hw initialization, but it's missing after
resuming.
Move the delay to the power on function to make sure that it is always
observerd. When at it, use fsleep() instead of usleep_range() as such a
narrow range is not required.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241001-veml6035-v3-1-d789f6ff147c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop the common 'dev_err() + return' combination in the probe function
and use 'return dev_err_probe()' instead.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240929-veml6070-cleanup-v1-7-a9350341a646@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the code by using devm_iio_device_register(), which removes the
need for a 'remove' function, as there are no more actions to take.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240929-veml6070-cleanup-v1-3-a9350341a646@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the code by adding an action to call i2c_unregister_device(),
which removes the need for a 'fail' label, gotos to it, and an explicit
call in veml6070_remove().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240929-veml6070-cleanup-v1-1-a9350341a646@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compatible 'ltr,ltrf216a' is used by Valve's Steamdeck device
via the ACPI + PRP0001 mechanism.
Document this info alongside the compatible.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Link: https://patch.msgid.link/20240923131527.1408691-1-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support to configure the threshold interrupt persistance value by
providing IIO_EV_INFO_PERIOD attribute. The value written to the
attribute should be in miliseconds and should be greater than the
sampling rate of the sensor.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20240914181246.504450-5-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for threshold events for both the ALS and UVI channels.
The events are reported when the threshold interrupt is triggered. Both
rising and falling threshold types are supported.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20240914181246.504450-4-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for suspend and resume PM ops.
We suspend the sensor by clearing the ALS_UVS_EN bit in the MAIN CONTROL
register. And we resume it by setting that bit.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20240914181246.504450-3-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provided configurable sampling frequency(Measurement rate) support.
Also exposed the available sampling frequency values using read_avail
callback.
Signed-off-by: Abhash Jha <abhashkumarjha123@gmail.com>
Link: https://patch.msgid.link/20240914181246.504450-2-abhashkumarjha123@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Instead of using regmap_update_bits() and passing
val == 1 == VEML6030_ALS_SD, use regmap_set_bits().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240913-veml6035-v1-4-0b09c0c90418@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If i2c_smbus_write_byte_data() fails in al3010_init(),
al3010_set_pwr(false) is not called.
In order to avoid such a situation, move the devm_add_action_or_reset()
witch calls al3010_set_pwr(false) right after a successful
al3010_set_pwr(true).
Fixes: c36b5195ab ("iio: light: add Dyna-Image AL3010 driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/ee5d10a2dd2b70f29772d5df33774d3974a80f30.1725993353.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
cm32181_acpi_parse_cpm_tables() is a no-op if ACPI handle
is not available. Remove duplicate ACPI handle check at
the caller side.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://patch.msgid.link/20240904183646.1219485-1-andy.shevchenko@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Access to platform data via dev_get_platdata() getter to make code cleaner.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20240902222824.1145571-18-andy.shevchenko@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
