Instead of asymmetrical checks for the firmware type use
the is_*_node() calls.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We have the same code flows in the PCI and platform drivers. Moreover,
the flow requires the common code to export a few functions. Instead,
consolidate that flow under new function called
i2c_dw_fw_parse_and_configure() and drop unneeded exports.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
For the sake of consistency, rename dw_i2c_of_configure() and change
its parameter to be aligned with the i2c_dw_acpi_configure().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Fast mode plus is available on most of the IP variants that RIIC driver
is working with. The exception is (according to HW manuals of the SoCs
where this IP is available) the Renesas RZ/A1H. For this, patch
introduces the struct riic_of_data::fast_mode_plus.
Fast mode plus was tested on RZ/G3S, RZ/G2{L,UL,LC}, RZ/Five by
instantiating the RIIC frequency to 1MHz and issuing i2c reads on the
fast mode plus capable devices (and the i2c clock frequency was checked on
RZ/G3S).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Define individual arrays to describe the register offsets. In this way
we can describe different IP variants that share the same register offsets
but have differences in other characteristics. Commit prepares for the
addition of fast mode plus.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add suspend/resume support for the RIIC driver. This is necessary for the
Renesas RZ/G3S SoC which support suspend to deep sleep state where power
to most of the SoC components is turned off. As a result the I2C controller
needs to be reconfigured after suspend/resume. For this, the reset line
was stored in the driver private data structure as well as i2c timings.
The reset line and I2C timings are necessary to re-initialize the
controller after resume.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Enable runtime PM autosuspend support for the RIIC driver. With this, in
case there are consecutive xfer requests the device wouldn't be runtime
enabled/disabled after each consecutive xfer but after the
the delay configured by user. With this, we can avoid touching hardware
registers involved in runtime PM suspend/resume saving in this way some
cycles. The default chosen autosuspend delay is zero to keep the
previous driver behavior.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
pm_runtime_get_sync() may return with error. In case it returns with error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is no need to runtime resume the device as long as the IP registers
are not accessed. Calling pm_runtime_get_sync() at the register access
time leads to a simpler error path.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use a temporary variable for the struct device pointers to avoid
dereferencing.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
dw_i2c_of_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
i2c_dw_acpi_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is no need to have ugly ifdeffery and additional macros
for the device ID tables. Always provide them. Since we touch
the ACPI table, make it sorted by ID.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Make the terminator entry look the same in all device ID tables.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
PCI core, after pcim_enable_device(), takes care about the allocated
IRQ vectors, no need to do it explicitly and break the cleaning up
order.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace a while-loop by for-loop in i2c_dw_probe_lock_support() to
save a few lines of code.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace SET_RUNTIME_PM_OPS() with its modern RUNTIME_PM_OPS()
alternative.
The combined usage of pm_ptr() and RUNTIME_PM_OPS() allows the
compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In the mtk_i2c_irq() handler, variable restart_flag is initialized
to zero and then reassigned with I2C_RS_TRANSFER if and only if
auto_restart is enabled.
Avoid a double initialization of this variable by transferring the
auto_restart check to the restart_flag declaration.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Delimiters are meant to be last, no need for a ',' there. Remove a
superfluous newline in the ali1535 driver while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When disabling CONFIG_X86_AMD_PLATFORM_DEVICE option, the driver
'drivers/acpi/acpi_apd.c' won't be compiled. This leads to a situation
where BMC (Baseboard Management Controller) cannot retrieve the memory
temperature via the i2c interface after i2c DW driver is loaded. Note
that BMC can retrieve the memory temperature before booting into OS.
[Debugging Detail]
1. dev->pclk and dev->clk are NULL when calling devm_clk_get_optional()
in dw_i2c_plat_probe().
2. The callings of i2c_dw_scl_hcnt() in i2c_dw_set_timings_master()
return 65528 (-8 in integer format) or 65533 (-3 in integer format).
The following log shows SS's HCNT/LCNT:
i2c_designware AMDI0010:01: Standard Mode HCNT:LCNT = 65533:65535
3. The callings of i2c_dw_scl_lcnt() in i2c_dw_set_timings_master()
return 65535 (-1 in integer format). The following log shows SS's
HCNT/LCNT:
i2c_designware AMDI0010:01: Fast Mode HCNT:LCNT = 65533:65535
4. i2c_dw_init_master() configures the register IC_SS_SCL_HCNT with
the value 65533. However, the DW i2c databook mentioned the value
cannot be higher than 65525. Quote from the DW i2c databook:
NOTE: This register must not be programmed to a value higher than
65525, because DW_apb_i2c uses a 16-bit counter to flag an
I2C bus idle condition when this counter reaches a value of
IC_SS_SCL_HCNT + 10.
5. Since ss_hcnt, ss_lcnt, fs_hcnt, and fs_lcnt are the invalid
values, we should not write the corresponding registers.
Fix the issue by reading dev->{ss,fs,hs}_hcnt and dev->{ss,fs,hs}_lcnt
from HW registers if ic_clk is not set.
Reported-by: Dong Wang <wangdong28@lenovo.com>
Suggested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Dong Wang <wangdong28@lenovo.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/linux-i2c/8295cbe1-a7c5-4a35-a189-5d0bff51ede6@linux.intel.com/
On ACPI machines, the tegra i2c module encounters an issue due to a
mutex being called inside a spinlock. This leads to the following bug:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
...
Call trace:
__might_sleep
__mutex_lock_common
mutex_lock_nested
acpi_subsys_runtime_resume
rpm_resume
tegra_i2c_xfer
The problem arises because during __pm_runtime_resume(), the spinlock
&dev->power.lock is acquired before rpm_resume() is called. Later,
rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on
mutexes, triggering the error.
To address this issue, devices on ACPI are now marked as not IRQ-safe,
considering the dependency of acpi_subsys_runtime_resume() on mutexes.
Fixes: bd2fdedbf2 ("i2c: tegra: Add the ACPI support")
Cc: <stable@vger.kernel.org> # v5.17+
Co-developed-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add the missing geni_icc_disable() call before returning in the
geni_i2c_runtime_resume() function.
Commit 9ba48db9f7 ("i2c: qcom-geni: Add missing
geni_icc_disable in geni_i2c_runtime_resume") by Gaosheng missed
disabling the interconnect in one case.
Fixes: bf225ed357 ("i2c: i2c-qcom-geni: Add interconnect support")
Cc: Gaosheng Cui <cuigaosheng1@huawei.com>
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add the missing clk_disable_unprepare() before return in
geni_i2c_runtime_resume().
Fixes: 14d02fbadb ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The piix4 I2C bus can carry SPDs, register them if present.
Only look on bus 0, as this is where the SPDs seem to be located.
Only the first 8 slots are supported. If the system has more,
then these will not be visible.
The AUX bus can not be probed as on some platforms it reports all
devices present and all reads return "0".
This would allow the ee1004 to be probed incorrectly.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
regarding unneeded 'driver_data' and more sanity checks in the char
device.
For the host drivers, this release includes significant updates, with
the primary change being the renaming from "master/slave" to
"controller/target" to adhere to I2C v7 and SMBus 3.2 standards.
New Support:
- Added support for Intel Arrow Lake-H.
- Added I2C support in the Arioha SoC by linking the Mediatek
I2C controller.
Cleanups:
- Added the MODULE_DESCRIPTION() macro, resolving a modpost
warning in the ALi 1563 Southbridge driver.
- Constified the regmap_config declaration in the i2c-designware
driver.
- Improved the coding style in the Renesas R-Car driver by
removing unnecessary semicolons after brackets.
General improvements:
- In the OMAP device, replaced NOIRQ_SYSTEM_SLEEP_PM_OPS with
RUNTIME_PM_OPS to enable waking up the controller during
suspend() before suspend_noirq() kicks in.
- Improved logging in the Xilinx driver.
- Added a warning (WARN()) in the Renesas R-Car driver for
spurious interrupts.
DTS Changes:
- Removed address-cell and size-cell from the Atmel at91sam,
nVidia Tegra 20, and Samsung S3c2410 devices.
- Fixed Texas Instruments OMAP4 I2C controller to comply with
the i2c-controller.yaml schema.
- Improved indentation in DTS examples for several I2C devices.
- Converted the NXP LPC1788 binding to the dt-schema.
- Added documentation for the compatible string
thead,th1520-i2c.
- Added the "power-domains" property for the Meson I2C driver.
AT24 EEPROM driver changes:
- add support for two new Microchip models
- document even more new models in DT bindings (those use fallback
compatibles so no code changes)
-----BEGIN PGP SIGNATURE-----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=perV
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.11-rc1-try2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The I2C core gains documentation updates for the testunit, a cleanup
regarding unneeded 'driver_data' and more sanity checks in the char
device.
For the host drivers, this release includes significant updates, with
the primary change being the renaming from "master/slave" to
"controller/target" to adhere to I2C v7 and SMBus 3.2 standards.
New Support:
- Added support for Intel Arrow Lake-H
- Added I2C support in the Arioha SoC by linking the Mediatek I2C
controller
Cleanups:
- Added the MODULE_DESCRIPTION() macro, resolving a modpost warning
in the ALi 1563 Southbridge driver.
- Constified the regmap_config declaration in the i2c-designware
driver.
- Improved the coding style in the Renesas R-Car driver by removing
unnecessary semicolons after brackets.
General improvements:
- In the OMAP device, replaced NOIRQ_SYSTEM_SLEEP_PM_OPS with
RUNTIME_PM_OPS to enable waking up the controller during suspend()
before suspend_noirq() kicks in.
- Improved logging in the Xilinx driver.
- Added a warning (WARN()) in the Renesas R-Car driver for spurious
interrupts.
DTS Changes:
- Removed address-cell and size-cell from the Atmel at91sam, nVidia
Tegra 20, and Samsung S3c2410 devices.
- Fixed Texas Instruments OMAP4 I2C controller to comply with the
i2c-controller.yaml schema.
- Improved indentation in DTS examples for several I2C devices.
- Converted the NXP LPC1788 binding to the dt-schema.
- Added documentation for the compatible string thead,th1520-i2c.
- Added the "power-domains" property for the Meson I2C driver.
AT24 EEPROM driver changes:
- add support for two new Microchip models
- document even more new models in DT bindings (those use fallback
compatibles so no code changes)"
* tag 'i2c-for-6.11-rc1-try2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (87 commits)
i2c: document new callbacks in i2c_algorithm
dt-bindings: i2c: amlogic,meson6-i2c: add optional power-domains
dt-bindings: i2c: at91: Add sama7d65 compatible string
i2c: st: reword according to newest specification
i2c: cpm: reword according to newest specification
i2c: virtio: reword according to newest specification
i2c: nvidia-gpu: reword according to newest specification
i2c: viai2c: reword according to newest specification
i2c: viperboard: reword according to newest specification
i2c: uniphier: reword according to newest specification
i2c: uniphier-f: reword according to newest specification
i2c: tiny-usb: reword according to newest specification
i2c: thunderx-pcidrv: reword according to newest specification
i2c: tegra-bpmp: reword according to newest specification
i2c: taos-evm: reword according to newest specification
i2c: sun6i-p2wi: reword according to newest specification
i2c: stm32f4: reword according to newest specification
i2c: sprd: reword according to newest specification
i2c: sis5595: reword according to newest specification
i2c: rzv2m: reword according to newest specification
...
Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit systems,
have been in linux-next for a while with no reported issues. The
Kconfig fixup went in 29 hours ago, so might have missed the latest
linux-next, but was acked by everyone involved.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppR4w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwoQCeIaW3nbOiNTmOupvEnZwrN3yVNs8An3Q5L+Br
1LpTASaU6A8pN81Z1m5g
=6U1z
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc and other driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit
systems, have been in linux-next for a while with no reported issues.
The Kconfig fixup went in 29 hours ago, so might have missed the
latest linux-next, but was acked by everyone involved"
* tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
misc: Kconfig: exclude mrvl-cn10k-dpi compilation for 32-bit systems
misc: delete Makefile.rej
binder: fix hang of unregistered readers
misc: Kconfig: add a new dependency for MARVELL_CN10K_DPI
virtio: add missing MODULE_DESCRIPTION() macro
agp: uninorth: add missing MODULE_DESCRIPTION() macro
spmi: add missing MODULE_DESCRIPTION() macros
dev/parport: fix the array out-of-bounds risk
samples: configfs: add missing MODULE_DESCRIPTION() macro
misc: mrvl-cn10k-dpi: add Octeon CN10K DPI administrative driver
misc: keba: Fix missing AUXILIARY_BUS dependency
slimbus: Fix struct and documentation alignment in stream.c
MAINTAINERS: CC dri-devel list on Qualcomm FastRPC patches
misc: fastrpc: use coherent pool for untranslated Compute Banks
misc: fastrpc: support complete DMA pool access to the DSP
misc: fastrpc: add missing MODULE_DESCRIPTION() macro
misc: fastrpc: Add missing dev_err newlines
misc: fastrpc: Use memdup_user()
nvmem: core: Implement force_ro sysfs attribute
nvmem: Use sysfs_emit() for type attribute
...
R-Car Gen3+ needs a reset before every controller transfer. That erases
configuration of a potentially in parallel running local target
instance. To avoid this disruption, avoid controller transfers if a
local target is running. Also, disable SMBusHostNotify because it
requires being a controller and local target at the same time.
Fixes: 3b770017b0 ("i2c: rcar: handle RXDMA HW behaviour on Gen3")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a superfluous debug output which is already available via
tracing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a superfluous debug output which is already available via
tracing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove and reword comments while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We should allow RXDMA only if the reset was really successful, so clear
the flag after the reset call.
Fixes: 0e864b552b ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
A newline was missing and closing braces of functions do not need a
semicolon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The FIXME is very old and probably needed because of some driver bug
like insufficient initialization. It may well be that it was fixed
meanwhile but we never know because the spurious irq is silently
ignored. Add now a call trace when this happens so we have more
information in case the issue still exists.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When probing, the hardware is not brought into a known state. This may
be a problem when a hypervisor restarts Linux without resetting the
hardware, leaving an old state running. Make sure the hardware gets
initialized, especially interrupts should be cleared and disabled.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/r/20240702045535.2000393-1-dirk.behme@de.bosch.com
Fixes: 6ccbe60713 ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce i2c support to Airoha EN7581 SoC through the i2c-mt7621
driver.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Ray Liu <ray.liu@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
`bt1_i2c_cfg` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
A device may need the controller up during suspend_noirq() or
resume_noirq().
But if the controller is autosuspended, there is no way to wakeup it during
suspend_noirq() or resume_noirq() because runtime pm is disabled at this
time.
The suspend() callback wakes up the controller, so it is available until
its suspend_noirq() callback (pm_runtime_force_suspend()).
During the resume, it's restored by resume_noirq() callback
(pm_runtime_force_resume()). Then resume() callback enables autosuspend.
So the controller is up during a little time slot in suspend and resume
sequences even if it's not used.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() by
NOIRQ_SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS().
The usage of pm_ptr() and these more recent macros allows the compiler to
see and drop the dead code.
The unnecessary '__maybe_unused' annotations on PM functions can be
removed.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-ccgx-ucsi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-ali1563.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-pxa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-qup.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When del_timer_sync() is called in an interrupt context it throws a warning
because of potential deadlock. The timer is used only to exit from
wait_for_completion() after a timeout so replacing the call with
wait_for_completion_timeout() allows to remove the problematic timer and
its related functions altogether.
Fixes: 41561f28e7 ("i2c: New Philips PNX bus driver")
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
'devmodel' hasn't actually been used since:
'commit 3275158fa5 ("parport: remove use of devmodel")'
and everyone now has it set to true and has been fixed up; remove
the flag.
(There are still comments all over about it)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240502154823.67235-4-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c-viai2c-common.c file is used by two drivers, but is not a proper
abstraction and can get linked into both modules in the same configuration,
which results in a warning:
scripts/Makefile.build:236: drivers/i2c/busses/Makefile: i2c-viai2c-common.o is added to multiple modules: i2c-wmt i2c-zhaoxin
The other problems with this include the incorrect use of a __weak function
when both are built-in, and the fact that the "common" module is sprinked
with 'if (i2c->plat == ...)' checks that have knowledge about the differences
between the drivers using it.
Avoid the link time warning by making the common driver a proper module
with MODULE_LICENCE()/MODULE_AUTHOR() tags, and remove the __weak function
by slightly rearranging the code.
This adds a little more duplication between the two main drivers, but
those versions get more readable in the process.
Fixes: a06b80e830 ("i2c: add zhaoxin i2c controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Hans Hu <HansHu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Setting IACK bit when core is disabled does not clear the "Interrupt Flag"
bit in the status register, and the interrupt remains pending.
Sometimes it causes failure for the very first message transfer, that is
usually a device probe.
Hence, set IACK bit after core is enabled to clear pending interrupt.
Fixes: 18f98b1e31 ("[PATCH] i2c: New bus driver for the OpenCores I2C controller")
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 5b6d721b26 ("i2c: designware: enable SLAVE in platform module")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Luis Oliveira <lolivei@synopsys.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
'pclk' is only used locally in the probe. Remove it from the
'synquacer_i2c' structure.
Also remove a useless debug message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
further deprecate class based I2C device instantiation. All users are
converted, too. Other that that, Andi collected a number if I2C host
driver patches. Those merges have their own description.
-----BEGIN PGP SIGNATURE-----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=viLd
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core removes an argument from the i2c_mux_add_adapter() call to
further deprecate class based I2C device instantiation. All users are
converted, too.
Other that that, Andi collected a number if I2C host driver patches.
Those merges have their own description"
* tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (72 commits)
power: supply: sbs-manager: Remove class argument from i2c_mux_add_adapter()
i2c: mux: Remove class argument from i2c_mux_add_adapter()
i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()
i2c: acpi: Unbind mux adapters before delete
i2c: designware: Replace MODULE_ALIAS() with MODULE_DEVICE_TABLE()
i2c: pxa: use 'time_left' variable with wait_event_timeout()
i2c: s3c2410: use 'time_left' variable with wait_event_timeout()
i2c: rk3x: use 'time_left' variable with wait_event_timeout()
i2c: qcom-geni: use 'time_left' variable with wait_for_completion_timeout()
i2c: jz4780: use 'time_left' variable with wait_for_completion_timeout()
i2c: synquacer: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f7: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f4: use 'time_left' variable with wait_for_completion_timeout()
i2c: st: use 'time_left' variable with wait_for_completion_timeout()
i2c: omap: use 'time_left' variable with wait_for_completion_timeout()
i2c: imx-lpi2c: use 'time_left' variable with wait_for_completion_timeout()
i2c: hix5hd2: use 'time_left' variable with wait_for_completion_timeout()
i2c: exynos5: use 'time_left' variable with wait_for_completion_timeout()
i2c: digicolor: use 'time_left' variable with wait_for_completion_timeout()
i2c: amd-mp2-plat: use 'time_left' variable with wait_for_completion_timeout()
...
- Updates to AMBA bus subsystem to drop .owner struct device_driver
initialisations, moving that to code instead.
- Add LPAE privileged-access-never support
- Add support for Clang CFI
- clkdev: report over-sized device or connection strings
-----BEGIN PGP SIGNATURE-----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=t/xl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux
Pull ARM updates from Russell King:
- Updates to AMBA bus subsystem to drop .owner struct device_driver
initialisations, moving that to code instead.
- Add LPAE privileged-access-never support
- Add support for Clang CFI
- clkdev: report over-sized device or connection strings
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux: (36 commits)
ARM: 9398/1: Fix userspace enter on LPAE with CC_OPTIMIZE_FOR_SIZE=y
clkdev: report over-sized strings when creating clkdev entries
ARM: 9393/1: mm: Use conditionals for CFI branches
ARM: 9392/2: Support CLANG CFI
ARM: 9391/2: hw_breakpoint: Handle CFI breakpoints
ARM: 9390/2: lib: Annotate loop delay instructions for CFI
ARM: 9389/2: mm: Define prototypes for all per-processor calls
ARM: 9388/2: mm: Type-annotate all per-processor assembly routines
ARM: 9387/2: mm: Rewrite cacheflush vtables in CFI safe C
ARM: 9386/2: mm: Use symbol alias for cache functions
ARM: 9385/2: mm: Type-annotate all cache assembly routines
ARM: 9384/2: mm: Make tlbflush routines CFI safe
ARM: 9382/1: ftrace: Define ftrace_stub_graph
ARM: 9358/2: Implement PAN for LPAE by TTBR0 page table walks disablement
ARM: 9357/2: Reduce the number of #ifdef CONFIG_CPU_SW_DOMAIN_PAN
ARM: 9356/2: Move asm statements accessing TTBCR into C functions
ARM: 9355/2: Add TTBCR_* definitions to pgtable-3level-hwdef.h
ARM: 9379/1: coresight: tpda: drop owner assignment
ARM: 9378/1: coresight: etm4x: drop owner assignment
ARM: 9377/1: hwrng: nomadik: drop owner assignment
...
A substantial code cleanup from Wolfram affects many drivers:
- Removed dev_err() in case of timeout during i2c transfers, as
timeouts are not considered errors and should not be treated
as such.
- For the same reason, 'timeout' variables have been renamed to
'time_left'.
Other cleanups:
- The viperboard driver now omits the "owner = THIS_MODULE"
assignment.
- Finally, we have eliminated the last remnants of
I2C_CLASS_SPD: support for class-based devices has been
completely removed from the mux-gpio driver.
- In the ocore devices, a more standard use of ioport_map() for
8-bit I/O read/write operations has been implemented.
- The mpc driver will be among the first i2c drivers and one of
the first in the kernel to use the __free auto cleanup
routine.
- The designware driver now uses MODULE_DEVICE_TABLE() instead
of MODULE_ALIAS() for better consistency with the ID table.
- Added prefixes to the octeon register macros.
- Fixed some checkpatch errors in the newly created
i2c-viai2c-common.c file.
Code refactoring:
- The riic driver has refactored read/write operations to more
flexibly support new platforms, laying the foundation for new
SoC peculiarities.
- In the i801 driver, a notifier callback has been created for
muxed child segments.
- The lpi2c driver now sets a clock rate during probe instead
of continuously calling clk_get_rate().
- Improvements in the clock divisor logic to accommodate other
clock frequencies.
- Combined some common functionalities during initialization
for the wmt driver and separated others that can be
independently used by different drivers. Now, all the common
functionalities are grouped in the i2c-viai2c-common.c file.
- Improved the clock stretching mechanism in the newly created
i2c-viai2c-common.c file, inherited from the previous
i2c-wmt.c.
Features added:
- The octeon driver now includes watchdog timeout handling.
- Added high-speed support for the octeon driver.
Added support for:
- R9A09G057 SoC in the riic driver.
- Rapids-D I2C controller in the designware driver.
- Cadence driver now also supports RISC-V architectures.
- Added support to the WMT device as a separate driver using the
newly created i2c-viai2c-common.c functionalities.
- Added support for the Zhaoxin I2C controller.
Some improvements in the bindings:
- The pnx driver is converted to dtschema.
- Added documentation for the Qualcomm SC8280XP.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZj/GzxYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1uJQgA/3DBT5R6OYbIg1Ky4u9A9hwwmqqN
EnNcygEovf1BpMiSAQC7Nrmv/CKUkmk0YNV9Ho94XYjFxIHqgKwUwySsocrFAQ==
=MW8c
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
Code cleanup:
A substantial code cleanup from Wolfram affects many drivers:
- Removed dev_err() in case of timeout during i2c transfers, as
timeouts are not considered errors and should not be treated
as such.
- For the same reason, 'timeout' variables have been renamed to
'time_left'.
Other cleanups:
- The viperboard driver now omits the "owner = THIS_MODULE"
assignment.
- Finally, we have eliminated the last remnants of
I2C_CLASS_SPD: support for class-based devices has been
completely removed from the mux-gpio driver.
- In the ocore devices, a more standard use of ioport_map() for
8-bit I/O read/write operations has been implemented.
- The mpc driver will be among the first i2c drivers and one of
the first in the kernel to use the __free auto cleanup
routine.
- The designware driver now uses MODULE_DEVICE_TABLE() instead
of MODULE_ALIAS() for better consistency with the ID table.
- Added prefixes to the octeon register macros.
- Fixed some checkpatch errors in the newly created
i2c-viai2c-common.c file.
Code refactoring:
- The riic driver has refactored read/write operations to more
flexibly support new platforms, laying the foundation for new
SoC peculiarities.
- In the i801 driver, a notifier callback has been created for
muxed child segments.
- The lpi2c driver now sets a clock rate during probe instead
of continuously calling clk_get_rate().
- Improvements in the clock divisor logic to accommodate other
clock frequencies.
- Combined some common functionalities during initialization
for the wmt driver and separated others that can be
independently used by different drivers. Now, all the common
functionalities are grouped in the i2c-viai2c-common.c file.
- Improved the clock stretching mechanism in the newly created
i2c-viai2c-common.c file, inherited from the previous
i2c-wmt.c.
Features added:
- The octeon driver now includes watchdog timeout handling.
- Added high-speed support for the octeon driver.
Added support for:
- R9A09G057 SoC in the riic driver.
- Rapids-D I2C controller in the designware driver.
- Cadence driver now also supports RISC-V architectures.
- Added support to the WMT device as a separate driver using the
newly created i2c-viai2c-common.c functionalities.
- Added support for the Zhaoxin I2C controller.
Some improvements in the bindings:
- The pnx driver is converted to dtschema.
- Added documentation for the Qualcomm SC8280XP.
If an error occurs after the clk_prepare_enable() call, it should be undone
by a corresponding clk_disable_unprepare() call, as already done in the
remove() function.
As devm_clk_get() is used, we can switch to devm_clk_get_enabled() to
handle it automatically and fix the probe.
Update the remove() function accordingly and remove the now useless
clk_disable_unprepare() call.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
As Krzysztof Kozlowski pointed out the better is to use
MODULE_DEVICE_TABLE() as it will be consistent with the content
of the real ID table of the platform devices.
While at it, drop unneeded and unused module alias in PCI glue
driver as PCI already has its own ID table and automatic loading
should just work.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231120144641.1660574-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout and turn
the SMBus-specific termination message to debug.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add Zhaoxin I2C controller driver. It provides the access to the i2c
busses, which connects to the touchpad, eeprom, I2S, etc.
Zhaoxin I2C controller has two separate busses, so may accommodate up
to two I2C adapters. Those adapters are listed in the ACPI namespace
with the IIC1D17 HID, and probed by a platform driver.
The driver works with IRQ mode, and supports basic I2C features. Flags
I2C_AQ_NO_ZERO_LEN and I2C_AQ_COMB_WRITE_THEN_READ are used to limit
the unsupported access.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Enumeration variables are added to differentiate
between different platforms.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
During each byte access, the host performs clock stretching.
To reduce the host performs clock stretching, move most of
the per-msg processing to the interrupt context.
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
1. The I2C IP for both wmt and zhaoxin originates from VIA. Rename
common registers, functions, and variable names to follow the
VIAI2C_ and viai2c_ naming conventions for consistency and clarity.
2. rename i2c_dev to i2c, to shorten the length of a line.
3. rename wait_result to time_left, make it better to reflect the meaning
of the value returned by wait_for_completion_timeout().
4. remove TCR_MASTER_WRITE, its value is 0.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Since the I2C IP of both wmt and zhaoxin originates from VIA,
it is better to separate the common code first.
The common driver is named as i2c-viai2c-common.c.
Old i2c-wmt.c renamed to i2c-viai2c-wmt.c.
The MAINTAINERS file will be updated accordingly in upcoming commits.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some common initialization actions are put in the function
wmt_i2c_init(), which is convenient to share with zhaoxin.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Read the ioclk property as reference clock if sclk not present in acpi
table to make it SOC agnostic.
In case, it's not populated from dts/acpi table, use the default clock
of 800 MHz which is optimal in either case of sclk/ioclk.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add watchdog timeout handling to cater to the unhandled warnings
seen during validation on boards with different I2C slaves.
This status code reflects the state that controller couldn't
receive any response from slave while being in non-idle state
and HW recommends to reset before any further bus access.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The macros for TWSI register's offset are generically
named, rename them to be platform specific macros by
adding 'OCTEON_REG' as prefix.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To support bus operations for high speed bus frequencies greater than
400KHZ following control bits need to be setup accordingly
- hs_mode (bit 0) field in Mode register to switch controller
between low-speed and high-speed frequency operating mode.
- Setup clock divisors for desired TWSI bus frequency using
FOSCL output frequency divisor (D):
0 - sets the divisor to 10 for low speed mode
1 - sets the divisor to 15 for high speed mode.
The TWSI bus output frequency, in master mode is based on:
TCLK = 100MHz / (THP + 2)
FOSCL = FSAMP / (M+1)×D = TCLK / (2 ^ N × (M + 1) × 15)
FSAMP = TCLK / 2 ^ N
where,
N is <2:0> and M is <6:3> of TWSI Clock Control Register
D is 10 for low speed or 15 for HS_MODE
With high speed mode support, HLC mode usage is limited to
low speed frequency (<=400KHz) bus transfers in hardware.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Handle changes to clock divisor logic for OcteonTX2 SoC family using
subsystem ID and using default reference clock source as 100MHz.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add RISCV support to Cadence I2C Kconfig which is used in platform
such as the StarFive JH8100.
Signed-off-by: Eng Lee Teh <englee.teh@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout and
simplify the logic a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Instead of repeatedly calling clk_get_rate for each transfer, lock
the clock rate and cache the value.
A deadlock has been observed while adding tlv320aic32x4 audio codec to
the system. When this clock provider adds its clock, the clk mutex is
locked already, it needs to access i2c, which in return needs the mutex
for clk_get_rate as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Annotate this variable as __ro_after_init to protect it from being
overwritten later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Only remaining client driver supporting I2C_CLASS_SPD is jc42. This
type of thermal sensor can be found on several DDR3/DDR4 modules.
i2c_register_spd() instantiates also such thermal sensor i2c devices.
Since 893fef0bc6 ("i2c: i801: Call i2c_register_spd for muxed child
segments") i2c_register_spd() is called also for the remaining use case,
systems with muxed SMBUS segments for SPD EEPROMs.
Therefore I2C_CLASS_SPD class-based instantiation isn't needed any longer
in this driver, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Granite Rapids-D has additional I2C controller that is enumerated via
ACPI. Add ACPI ID for it.
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Remove of_node_put from node_ctrl and node struct device_nodes.
Move the declaration to initialization for ensuring scope sanity.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Abhinav Jain <jain.abhinav177@gmail.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The original change adds usage of i2c_root_adapter(), which is
implemented in i2c-mux.c. Therefore we can't use the multiplexing
if I2C_I801=y and I2C_MUX=m.
Handling the dependencies in the code would become unnecessarily
complex, therefore create a new config symbol.
Fixes: 893fef0bc6 ("i2c: i801: Call i2c_register_spd for muxed child segments")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404042206.MjAQC32x-lkp@intel.com/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is at least one machine that uses this driver but does not
have support for inb()/outb() instructions.
Convert this to using ioport_map() so it can build on architectures
that don't provide these but work correctly on machines that require
using port I/O.
Fixes: 47c21d2d52 ("i2c: add HAS_IOPORT dependencies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/lkml/CAMuHMdVUQ2WgtpYPYfO2T=itMmZ7w=geREqDtsP8Q3ODh9rxdw@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The Driver unintentionally programs ctrl reg to clear the fifo, which
happens after the start of transaction. Previously, this was not an issue
as it involved read-modified-write. However, this issue breaks i2c reads
on QEMU, as i2c-read is executed before guest starts programming control
register.
Fixes: ff0cf7bca6 ("i2c: cadence: Remove unnecessary register reads")
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Once the gpio mux driver binds to the "i2c-mux-gpio" platform device,
this creates the i2c adapters for the muxed child segments.
We can use the bus notifier mechanism to check for creation of the
child i2c adapters, and call i2c_register_spd() for them. This allows
to detect all DIMM's on systems with more than 8 memory slots.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Extend the RIIC driver to support the RZ/V2H(P) ("R9A09G057") SoC. It
accomplishes this by appending the compatible string list and passing
the RZ/V2H-specific OF data.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
With an increasing number of SoCs reusing this driver, each with slight
variations in the RIIC IP, it becomes necessary to support passing these
details as OF data. This approach simplifies the extension of the driver
for other SoCs.
This patch lays the groundwork for adding support for the Renesas RZ/V2H
SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce helper functions for performing I2C read and write operations
in the RIIC driver.
These helper functions lay the groundwork for adding support for the
RZ/V2H SoC. This is essential because the register offsets for the RZ/V2H
SoC differ from those of the RZ/A SoC. By abstracting the read and write
operations, we can seamlessly adapt the driver to support different SoC
variants without extensive modifications.
This patch is part of the preparation process for integrating support for
the RZ/V2H SoC into the RIIC driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Amba bus core already sets owner, so driver does not need to.
Link: https://lore.kernel.org/r/20240326-module-owner-amba-v1-14-4517b091385b@linaro.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The function using this is hidden in an #ifdef, so the variable
needs the same one for a clean W=1 build:
drivers/i2c/busses/i2c-pxa.c:327:26: error: 'icr_bits' defined but not used [-Werror=unused-const-variable=]
Fixes: d6a7b5f84b ("[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Commit 857cc04cdf ("i2c: i801: Add helper i801_get_block_len")
introduced a slight functional change: the status variable is now
overwritten with the length of an SMBUS tranasaction,
even in case of success.
This breaks the touchpad on at least my Lenovo P1:
rmi4_physical rmi4-00: Read PDT entry at 0x00e9 failed, code: -6.
rmi4_physical rmi4-00: RMI initial reset failed! Continuing in spite of this.
rmi4_physical rmi4-00: Read PDT entry at 0x00e9 failed, code: -6.
rmi4_physical rmi4-00: IRQ counting failed with code -6.
Fixes: 857cc04cdf ("i2c: i801: Add helper i801_get_block_len")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
This patch is followed by eight commits featuring improvements to
the Nomadik controller, such as simplification of the IRQ logic,
renaming of the private data structure, more efficient use of
FIELD_PREP/GET, GENMASK, etc., better time measurement with
ktime, and more.
Two device trees have been added, but those need to be applied
elsewhere.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZfLnNBYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1uSSkBAKl75gzjiN2AglPaTUDfhCeux8yf
mISgvl4MWKCXXsZ5AQDjRiG+whrV7knOjS7L/r5owb30uF+Bv3d29sG4LVNsBQ==
=RubU
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-6.9-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
Théo adds support for the Mobileye EyeQ5-I2C in the bindings.
This patch is followed by eight commits featuring improvements to
the Nomadik controller, such as simplification of the IRQ logic,
renaming of the private data structure, more efficient use of
FIELD_PREP/GET, GENMASK, etc., better time measurement with
ktime, and more.
and are described by Andi in the merge commit
-----BEGIN PGP SIGNATURE-----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=Hm22
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Minor changes to the I2C core. Most changes are in drivers:
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations, such as
isolating faulty channels and flushing stuck buses, among others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4"
* tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: sprd: Convert to platform remove callback returning void
Documentation: i2c: Document that client auto-detection is a legacy mechanism
i2c: remove redundant condition
i2c: rcar: Prepare for the advent of ARCH_RCAR_GEN4
i2c: imx-lpi2c: add generic GPIO recovery for LPI2C
i2c: cadence: Add system suspend and resume PM support
i2c: mpc: remove outdated macro
i2c: mpc: use proper binding for transfer timeouts
dt-bindings: i2c: mpc: use proper binding for transfer timeouts
i2c: smbus: Prepare i2c_register_spd for usage on muxed segments
i2c: constify the struct device_type usage
i2c: designware: Implement generic polling mode code for Wangxun 10Gb NIC
i2c: designware: Fix RX FIFO depth define on Wangxun 10Gb NIC
i2c: designware: Move interrupt handling functions before i2c_dw_xfer()
i2c: designware: Use accessors to DW_IC_INTR_MASK register
i2c: designware: Do not enable interrupts shortly in polling mode
i2c: designware: Uniform initialization flow for polling mode
dt-bindings: i2c: at91: Add sam9x7 compatible string
dt-bindings: i2c: imx-lpi2c: add i.MX95 LPI2C
i2c: Remove redundant comparison in npcm_i2c_reg_slave
...
Add compatible for the integration of the same DB8500 IP block into the
Mobileye EyeQ5 platform. Two quirks are present:
- The memory bus only supports 32-bit accesses. Avoid writeb() and
readb() by introducing helper functions that fallback to writel()
and readl().
- A register must be configured for the I2C speed mode; it is located
in a shared register region called OLB. We access that memory region
using a syscon & regmap that gets passed as a phandle (mobileye,olb).
A two-bit enum per controller is written into the register; that
requires us to know the global index of the I2C controller (cell arg
to the mobileye,olb phandle).
We add #include <linux/mfd/syscon.h> and <linux/regmap.h>.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Allow overriding the default timeout value (200ms) from devicetree,
using the generic i2c-transfer-timeout-us property.
The i2c_adapter->timeout field is an unaccurate jiffies amount;
i2c-nomadik uses hrtimers for timeouts below one jiffy.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The FIFO flush function uses a jiffies amount to detect timeouts as the
flushing is async. Replace with ktime to get more accurate precision
and support short timeouts.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace the completion by a waitqueue for synchronization from IRQ
handler to task. For short timeouts, use hrtimers, else use timers.
Usecase: avoid blocking the I2C bus for too long when an issue occurs.
The threshold picked is one jiffy: if timeout is below that, use
hrtimers. This threshold is NOT configurable.
Implement behavior but do NOT change fetching of timeout. This means the
timeout is unchanged (200ms) and the hrtimer case will never trigger.
A waitqueue is used because it supports both desired timeout approaches.
See wait_event_timeout() and wait_event_hrtimeout(). An atomic boolean
serves as synchronization condition.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Constant register bit fields are declared using hardcoded hex values;
replace them by calls to BIT() and GENMASK(). Replace custom GEN_MASK()
macro by the generic FIELD_PREP(). Replace manual bit manipulations by
the generic FIELD_GET() macro.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations,
such as isolating faulty channels and flushing stuck buses, among
others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming rcar Gen4.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZesABRYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1u8aoA+gL2FSeXedSkhMfaPjyzYv9rsTaH
vm2C3d3l3Uq9IAJHAP9DeH+uz6y02AytDakz3gEgkaIXyAtZBitndC4OsbBHCQ==
=Kv2c
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations,
such as isolating faulty channels and flushing stuck buses, among
others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4.
Disambiguate the usage of dev as a variable name; it is usually best to
keep it reserved for struct device pointers. Avoid having multiple
names for the same struct pointer (previously: dev, nmk, nmk_i2c).
Fix whitespace code style; return indented twice, spacing besides infix
operators, align function call arguments to opening parenthesis. Remove
useless cast to unused return value from init_hw(). Introduce local dev
variable in probe() to alias &adev->dev.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When the i2c error condition occurred and master state was not
idle, the master irq function will goto complete state without any
other interrupt handling. It would cause dummy irq expected print.
Under this condition, assign the irq_status into irq_handle.
For example, when the abnormal start / stop occurred (bit 5) with
normal stop status (bit 4) at same time. Then the normal stop status
would not be handled and it would cause irq expected print in
the aspeed_i2c_bus_irq.
...
aspeed-i2c-bus x. i2c-bus: irq handled != irq.
Expected 0x00000030, but was 0x00000020
...
Fixes: 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events properly")
Cc: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
wmt_i2c_reset_hardware() calls clk_prepare_enable(). So, should an error
occur after it, it should be undone by a corresponding
clk_disable_unprepare() call, as already done in the remove function.
Fixes: 560746eb79 ("i2c: vt8500: Add support for I2C bus on Wondermedia SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
i801_probe_optional_slaves() is called before i801_add_mux().
This results in mux_pdev being checked before it's set by
i801_add_mux(). Fix this by changing the order of the calls.
I consider this safe as I see no dependencies.
Fixes: 80e56b86b5 ("i2c: i801: Simplify class-based client device instantiation")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently, all Kconfig symbols for R-Car Gen4 SoCs select
ARCH_RCAR_GEN3, which might confuse the casual reader. Prepare for the
advent of ARCH_RCAR_GEN4 by extending the dependency for auto-selecting
reset controller support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
This adds i2c bus recovery to the lpi2c driver.
Uses the generic recovery function setting the SCL/SDA pads as
GPIO pins and sending 9 clocks to try and recover the bus.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Enable device system suspend and resume PM support, and mark the device
state as suspended during system suspend to reject any data transfer.
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
DRV_NAME was useful back in the days. But here, being used once, it is
only cruft.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
"i2c-scl-clk-low-timeout-us" is wrongly used here because it describes
maximum clock stretching not maximum transfer time. Additionally, it is
deprecated because of issues. Move this driver to the correct binding.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I got an idea the i2c-designware should not need duplicated state
machines for the interrupt and polling modes. The IP is practically the
same and state transitions happens in response to the events that can be
observed from the DW_IC_RAW_INTR_STAT register. Either by interrupts or
by polling.
Another reasons are the interrupt mode is the most tested, has handling
for special cases as well as transmit abort handling and those are
missing from two polling mode quirks.
Patch implements a generic polling mode by using existing code for
interrupt mode. This is done by moving event handling from the
i2c_dw_isr() into a new i2c_dw_process_transfer() that will be called
both from the i2c_dw_isr() and a polling loop.
Polling loop is implemented in a new i2c_dw_wait_transfer() that is
shared between both modes. In interrupt mode it waits for the completion
object as before. In polling mode both completion object and
DW_IC_RAW_INTR_STAT are polled to determine completed transfer and state
transitions.
Loop tries to save power by sleeping "stetson guessed" range between
3 and 25 µS which falls between 10 cycles of High-speed mode 3.4 Mb/s
and Fast mode 400 kHz. With it the CPU usage was reduced under heavy
Fast mode I2C transfer without much increase in total transfer time but
otherwise no more effort has been put to optimize this.
I decided to convert the txgbe_i2c_dw_xfer_quirk() straight to generic
polling mode code in this patch. It doesn't have HW dependent quirks
like the amd_i2c_dw_xfer_quirk() does have and without users this patch
is needless.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I believe RX FIFO depth define 0 is incorrect on Wangxun 10Gb NIC. It
must be at least 1 since code is able to read received data from the
DW_IC_DATA_CMD register.
For now this define is irrelevant since the txgbe_i2c_dw_xfer_quirk()
doesn't use the rx_fifo_depth member variable of struct dw_i2c_dev but
is needed when converting code into generic polling mode implementation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Code is more logically arranged when i2c_dw_read_clear_intrbits() and
i2c_dw_isr() are located before i2c_dw_xfer().
Real reason for this is to prepare for more shared code between
interrupt and polling mode code.
While at it, remove one extra space and refer to the
i2c_dw_init_master() in two comment sections.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Convert access to DW_IC_INTR_MASK register using the existing
__i2c_dw_write_intr_mask() and a __i2c_dw_read_intr_mask() introduced
here. Motivation to this is to prepare for generic polling mode code
where polling mode will use a SW mask instead of DW_IC_INTR_MASK.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I was testing the polling mode txgbe_i2c_dw_xfer_quirk() on a HW where
the i2c-designware has interrupt connected and shared with other device.
I noticed there is a bogus interrupt for each transfer.
Reason for this that both polling mode functions call the
i2c_dw_xfer_init() which enable interrupts then followed by immediate
disable by the same polling mode functions. This is enough to trigger
TX_EMPTY interrupt.
Fix this by introducing a __i2c_dw_write_intr_mask() helper that unmasks
interrupts conditionally and use it in i2c_dw_xfer_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently initialization flow in i2c_dw_probe_master() skips a few steps
and has code duplication for polling mode implementation.
Simplify this by adding a new ACCESS_POLLING flag that is set for those
two platforms that currently use polling mode and use it to skip
interrupt handler setup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd692 ("i2c: imx: support slave mode for imx I2C driver")
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In the npcm_i2c_reg_slave() function, there was a redundant
comparison that checked if 'bus->slave' was null immediately after
assigning it the 'client' value. There were concerns about a
potential null dereference because of `client->adapter`, but
according to Wolfram Sang, "we trusted ourselves here" Therefore,
this comparison is unnecessary.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c94 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
On powerpc, it is possible to compile test both the new apple (arm) and
old pasemi (powerpc) drivers for the i2c hardware at the same time,
which leads to a warning about linking the same object file twice:
scripts/Makefile.build:244: drivers/i2c/busses/Makefile: i2c-pasemi-core.o is added to multiple modules: i2c-apple i2c-pasemi
Rework the driver to have an explicit helper module, letting Kbuild
take care of whether this should be built-in or a loadable driver.
Fixes: 9bc5f4f660 ("i2c: pasemi: Split pci driver to its own file")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.
I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().
TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).
Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
required before start of the transfer.
- DMA TRE : contains DDR/Memory address, called as DMA descriptor.
- GO TRE : contains Transfer directions, slave ID, Delay flags, Length
of the transfer.
I2c driver calls GPI driver API to config each TRE depending on the
protocol.
For read operation tre sequence will be as below which is not aligned
to hardware programming guide.
- CONFIG tre
- DMA tre
- GO tre
As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.
- CONFIG tre
- GO tre
- DMA tre
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Avoid code duplication and factor out retrieving and checking the
block length value to new helper i801_get_block_len().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add a sentinel length value that is used to check whether we should
read and use the length value provided by the slave device.
This simplifies the currently used checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
i2c and smbus block transaction handling have little in common,
therefore split this function to improve code readability.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Avoid code duplication and factor out checking and clearing PEC error
bit to new helper i801_check_and_clear_pec_error().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
This change simplifies the code a little and makes clearer that the
ICH5 feature set is an extension of the ICH4 feature set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The driver receives the tx fifo almost empty(aempty) interrupt and
reads the tx_aempty_int_mstat to start a round of data transfer.
The operation of clearing the TX aempty interrupt after completing
a write cycle is added to ensure that the FIFO is truly at almost
empty status when an aempty interrupt is received.
The threshold for fifo almost empty interrupt is defined as 1.
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The driver finishes a write cycle by read the fifo tx full status
or write limit decrease to 0. The driver starts to write data to
the FIFO after the I2C FIFO almost empty interrupt is reported.
The threshold for FIFO almost empty interrupt is that the amount
of data in the FIFO is less than or equal to 1.
Reduce write maxwrite to the fifo depth - aempty interrupt
threshold. Limiting the number of data to be written at a time
to remaining fifo capacity.
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Switch the R-Mobile A1, R-Mobile APE6, and SH-Mobile AG5 SoCs to the new
frequency calculation formula, to (a) avoid running the I2C bus too fast,
and (b) bring the low/high ratio closer to the recommended ratio 5/4.
As this makes fast_clock_dt_config and v2_freq_calc_dt_config identical,
merge them into a single fast_clock_dt_config.
Legacy SH users (sh7343, sh7366, and sh772[234]) are left alone, and
still use the old formula.
Measurement results on R-Mobile APE6 and SH-Mobile AG5 (fck=104 MHz,
clks_per_count=2):
100 kHz: 106 kHz LH=1.12 before, 99.6 kHz L/H=1.22 after
400 kHz: 384 kHz LH=1.67 before, 392 kHz L/H=1.27 after
Measurement results on R-Mobile A1 (fck=49.5 MHz, clks_per_count=1):
100 kHz: 106 kHz L/H=1.09 before, 99.6 kHz L/H=1.20 after
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Starting with
commit 75820314de ("i2c: core: add generic I2C GPIO recovery")
GPIO bus recovery is supported by the I2C core, so we can remove the
driver implementation and use that one instead.
As a nice side-effect, pinctrl becomes optional, allowing bus recovery on
LS1021A, which does not have such luxury, but can be wired up to use extra
fixed GPIO pins.
Note: The previous error messages about bus recovery not being supported is
dropped with this change. Given that it is perfectly possible to have platforms
where bus recovery works without pinctrl support, I happen to work on one such,
both error messages does not really make sense in those cases. And I don't see
how to know if this is the case or not.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
(controllers set the flag, but there is no client to use it). Also,
CLASS_SPD support gets simplified to prepare removal in the future.
Class based instantiation is not recommended these days anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it. Then, there are also
quite some driver updates. Standing out are patches for the wmt-driver
which is refactored to support more variants. This is the rebased pull
request where a large series for the designware driver was dropped.
-----BEGIN PGP SIGNATURE-----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=8D3Q
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
The stm32mp25 has only a single interrupt line used for both
events and errors. In order to cope with that, reorganise the
error handling code so that it can be called either from the
common handler (used in case of SoC having only a single IT line)
and the error handler for others.
The CR1 register also embeds a new FMP bit, necessary when running
at Fast Mode Plus frequency. This bit should be used instead of
the SYSCFG bit used on other platforms.
Add a new compatible to distinguish between the SoCs and two
boolean within the setup structure in order to know if the
platform has a single/multiple IT lines and if the FMP bit
within CR1 is available or not.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move readl_relaxed of I2C_ISR register at beginning of event isr
so that it done once for both master & slave handling.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Avoid usage of __func__ when reporting an error message
since dev_err/dev_dbg are already providing enough details
to identify the source of the message.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The irq handling is currently split between the irq handler
and the threaded irq handler. Some of the handling (such as
dma related stuffs) done within the irq handler might sleep or
take some time leading to issues if the kernel is built with
realtime constraints. In order to fix that, perform an overall
rework to perform most of the job within the threaded handler
and only keep fifo access in the non threaded handler.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert error handling upon calls of devm_request_irq functions during
the probe of the driver.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On the Dell XPS 15 7590/0VYV0G, BIOS 1.24.0 09/11/2023, Linux prints the
warning below.
i801_smbus 0000:00:1f.4: Accelerometer lis3lv02d is present on SMBus but its address is unknown, skipping registration
Following the same suggestions by Wolfram Sang as for the Dell Precision
3540 [1], the accelerometer can be successfully found on I2C bus 2 at
address 0x29.
$ echo lis3lv02d 0x29 | sudo tee /sys/bus/i2c/devices/i2c-2/new_device
lis3lv02d 0x29
$ dmesg | tail -5
[ 549.522876] lis3lv02d_i2c 2-0029: supply Vdd not found, using dummy regulator
[ 549.522904] lis3lv02d_i2c 2-0029: supply Vdd_IO not found, using dummy regulator
[ 549.542486] lis3lv02d: 8 bits 3DC sensor found
[ 549.630022] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input35
[ 549.630586] i2c i2c-2: new_device: Instantiated device lis3lv02d at 0x29
So, the device has that accelerometer. Add the I2C address to the
mapping list, and test it successfully on the device.
[1]: https://lore.kernel.org/linux-i2c/97708c11-ac85-fb62-2c8e-d37739ca826f@molgen.mpg.de/
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On the Dell Precision 3540/0M14W7, BIOS 1.7.4 05/12/2020, Linux prints
the warning below.
i801_smbus 0000:00:1f.4: Accelerometer lis3lv02d is present on SMBus but its address is unknown, skipping registration
With the help of Wolfram Sang, the test to probe it on I2C bus 6 at address
0x29 was successful.
$ echo lis3lv02d 0x29 | sudo tee /sys/bus/i2c/devices/i2c-6/new_device
[ 2110.787000] i2c i2c-6: new_device: Instantiated device lis3lv02d at 0x29
[ 2110.791932] lis3lv02d_i2c 6-0029: supply Vdd not found, using dummy regulator
[ 2110.791981] lis3lv02d_i2c 6-0029: supply Vdd_IO not found, using dummy regulator
[ 2110.809233] lis3lv02d: 8 bits 3DC sensor found
[ 2110.900668] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input23
So, the device has that accelerometer. Add the I2C address to the
mapping list.
Link: https://lore.kernel.org/linux-i2c/97708c11-ac85-fb62-2c8e-d37739ca826f@molgen.mpg.de/
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
[wsa: shortened commit message a little]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
These Settings for the same register, REG_CR,
can be put together to reduce code redundancy.
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use more appropriate parameter passing to reduce the amount of code
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The frequency setting mode is adjusted to reduce the code redundancy,
and it is also convenient to share with zhaoxin
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Put the handling of interrupt events in a function class
to reduce code redundancy.
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Put wmt_i2c_wait_bus_not_busy() in a more appropriate place
to reduce code redundancy
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
sparse reports an error on some data that gets converted from be32.
That's because that data is typed u32 instead of __be32.
The type is correct, the be32_to_cpu() conversion is not.
Remove the conversion.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312042210.QL4DA8Av-lkp@intel.com/
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-By: Jochen Friedrich <jochen@scram.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Both i2c_generic_scl_recovery() and the debug output indicate that SDA is
purely optional for bus recovery. But devm_gpiod_get() never returns NULL
making it mandatory. Fix this by calling devm_gpiod_get_optional instead.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rockchip RV1126 is using old style i2c controller, the i2c2
bus uses a non-sequential offset in the grf register for the
mask/value bits for this bus.
This patch fixes i2c2 bus on rv1126 SoCs.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for atomic transfers using polling mode with interrupts
intentionally disabled to get rid of the following warning introduced by
commit 63b96983a5 ("i2c: core: introduce callbacks for atomic
transfers") during system reboot and power-off:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1518 at drivers/i2c/i2c-core.h:40 i2c_transfer+0xe8/0xf4
No atomic I2C transfer handler for 'i2c-0'
...
---[ end trace 0000000000000000 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To support FM+, we mainly need to turn the SMD constant into a parameter
and set it accordingly. That also means we can finally fix SMD to our
needs instead of bailing out. A sanity check for SMD then becomes a
sanity check for 'x == 0'. After all that, activating the enable bit for
FM+ is all we need to do. Tested with a Renesas Falcon board using R-Car
V3U.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
So far, we treated Gen4 as Gen3. But we are soon adding FM+ as a Gen4
specific feature, so prepare the code for the new devtype.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C core now provides a per-adapter debugfs directory. Use it
instead of creating a custom one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C core now provides a per-adapter debugfs directory. Use it
instead of creating a custom one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After removal of the legacy eeprom driver the only remaining I2C
client device driver supporting I2C_CLASS_SPD is jc42. Because this
driver also supports I2C_CLASS_HWMON, adapters don't have to
declare support for I2C_CLASS_SPD if they support I2C_CLASS_HWMON.
It's one step towards getting rid of I2C_CLASS_SPD mid-term.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jim Cromie <jim.cromie@gmail.com> # for SCX
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350b ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Possible deadlock scenario (on reboot):
rk3x_i2c_xfer_common(polling)
-> rk3x_i2c_wait_xfer_poll()
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock);
...
<rk3x i2c interrupt>
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock); (deadlock here)
Store the IRQ number and disable/enable it around the polling transfer.
This patch has been tested on NanoPC-T4.
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add missing clk_disable_unprepare() and geni_se_resources_off() in the error
path in geni_i2c_probe().
Fixes: 14d02fbadb ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When an I2C device contains a wake IRQ subordinate to a regmap-irq chip,
the regmap-irq code must be able to perform I2C transactions during
suspend_device_irqs() and resume_device_irqs(). Therefore, the bus must
be suspended/resumed during the NOIRQ phase.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When running on a many core ARM64 server, errors were
happening in the ISR that looked like corrupted memory. These
corruptions would fix themselves if small delays were inserted
in the ISR. Errors reported by the driver included "i2c_designware
APMC0D0F:00: i2c_dw_xfer_msg: invalid target address" and
"i2c_designware APMC0D0F:00:controller timed out" during
in-band IPMI SSIF stress tests.
The problem was determined to be memory writes in the driver were not
becoming visible to all cores when execution rapidly shifted between
cores, like when a register write immediately triggers an ISR.
Processors with weak memory ordering, like ARM64, make no
guarantees about the order normal memory writes become globally
visible, unless barrier instructions are used to control ordering.
To solve this, regmap accessor functions configured by this driver
were changed to use non-relaxed forms of the low-level register
access functions, which include a barrier on platforms that require
it. This assures memory writes before a controller register access are
visible to all cores. The community concluded defaulting to correct
operation outweighed defaulting to the small performance gains from
using relaxed access functions. Being a low speed device added weight to
this choice of default register access behavior.
Signed-off-by: Jan Bottorff <janb@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 0b01392c18.
Conversion of PXA to generic I2C recovery, makes the I2C bus completely
lock up if recovery pinctrl is present in the DT and I2C recovery is
enabled.
So, until the generic I2C recovery can also work with PXA lets revert
to have working I2C and I2C recovery again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: stable@vger.kernel.org # 5.11+
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
While the preamble field _is_ technically big-endian, its value is always 0x2A2A,
which is the same in either endianness. However, to avoid generating a warning,
we should still call `htons()` explicitly.
Signed-off-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add the code to handle an invalid state when both bits S_RX_EVENT
(indicating a transaction) and S_START_BUSY (indicating the end
of transaction - transition of START_BUSY from 1 to 0) are set in
the interrupt status register during a slave read.
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Fixes: 1ca1b45160 ("i2c: iproc: handle Master aborted error")
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions... you
name it. The core got a memleak fix and better support for nested muxes.
-----BEGIN PGP SIGNATURE-----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=nfX/
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has largely driver updates for 6.7, i.e. feature additions (like
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions...
you name it.
The core got a memleak fix and better support for nested muxes"
* tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: s3c2410: make i2c_s3c_irq_nextbyte() void
i2c: qcom-geni: add ACPI device id for sc8180x
Documentation: i2c: add fault code for not supporting 10 bit addresses
i2c: sun6i-p2wi: Prevent potential division by zero
i2c: mux: demux-pinctrl: Convert to use sysfs_emit_at() API
i2c: i801: Use new helper acpi_use_parent_companion
ACPI: Add helper acpi_use_parent_companion
MAINTAINERS: add YAML file for i2c-demux-pinctrl
i2c: core: fix lockdep warning for sparsely nested adapter chain
i2c: axxia: eliminate kernel-doc warnings
dt-bindings: i2c: i2c-demux-pinctrl: Convert to json-schema
i2c: stm32f7: Use devm_clk_get_enabled()
i2c: stm32f4: Use devm_clk_get_enabled()
i2c: stm32f7: add description of atomic in struct stm32f7_i2c_dev
i2c: fix memleak in i2c_new_client_device()
i2c: exynos5: Calculate t_scl_l, t_scl_h according to i2c spec
i2c: i801: Simplify class-based client device instantiation
i2c: exynos5: add support for atomic transfers
i2c: at91-core: Use devm_clk_get_enabled()
eeprom: at24: add ST M24C64-D Additional Write lockable page support
...
Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for new
hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio, spi,
and i2c drivers for that type of device (all acked by the respective
subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems, EXCEPT for some merge conflicts that you will run
into in your tree. 2 of them are in device-tree files, which will be
trivial to resolve (accept both sides), and the last in the
drivers/gpio/gpio-ljca.c file, in the remove callback, resolution should
be pretty trivial (take the version in this branch), see here:
https://lore.kernel.org/all/20231016134159.11d8f849@canb.auug.org.au/
for details, or I can provide a resolved merge point if needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUStew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxgQCggUyfGo+JVV8XZVu5A9KwT6nr7mUAmwUgFxhZ
khK77t0KqF4hjXryeaHa
=iPd+
-----END PGP SIGNATURE-----
Merge tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
- Add symbol definitions related to CDAT to the ACPICA code (Dave
Jiang).
- Use the acpi_device_is_present() helper in more places and rename
acpi_scan_device_not_present() to be about enumeration (James Morse).
- Add __printf format attribute to acpi_os_vprintf() (Su Hui).
- Clean up departures from kernel coding style in the low-level
interface for ACPICA (Jonathan Bergh).
- Replace strncpy() with strscpy() in acpi_osi_setup() (Justin Stitt).
- Fail FPDT parsing on zero length records and add proper handling for
fpdt_process_subtable() to acpi_init_fpdt() (Vasily Khoruzhick).
- Rework acpi_handle_list handling so as to manage it dynamically,
including size computation (Rafael Wysocki).
- Clean up ACPI utilities code so as to make it follow the kernel
coding style (Jonathan Bergh).
- Consolidate IRQ trigger-type override DMI tables and drop .ident
values from dmi_system_id tables used for ACPI resources management
quirks (Hans de Goede).
- Add ACPI IRQ override for TongFang GMxXGxx (Werner Sembach).
- Allow _DSD buffer data only for byte accessors and document the _DSD
data buffer GUID (Andy Shevchenko).
- Drop BayTrail and Lynxpoint pinctrl device IDs from the ACPI LPSS
driver, because it does not need them (Raag Jadav).
- Add acpi_backlight=vendor quirk for Toshiba Portégé R100 (Ondrej
Zary).
- Add "vendor" backlight quirks for 3 Lenovo x86 Android tablets (Hans
de Goede).
- Move Xiaomi Mi Pad 2 backlight quirk to its own section (Hans de
Goede).
- Annotate struct prm_module_info with __counted_by (Kees Cook).
- Fix AER info corruption in aer_recover_queue() when error status data
has multiple sections (Shiju Jose).
- Make APEI use ERST maximum execution time for slow devices (Jeshua
Smith).
- Add support for platform notification handling to the PCC mailbox
driver and modify it to support shared interrupts for multiple
subspaces (Huisong Li).
- Define common macros to use when referring to various bitfields in the
PCC generic communications channel command and status fields and use
them in some drivers (Sudeep Holla).
- Add EC GPE detection quirk for HP 250 G7 Notebook PC (Jonathan
Denose).
- Fix and clean up create_pnp_modalias() and create_of_modalias()
(Christophe JAILLET).
- Modify 2 pieces of code to use acpi_evaluate_dsm_typed() (Andy
Shevchenko).
- Define acpi_dev_uid_match() for matching _UID and use it in several
places (Raag Jadav).
- Use acpi_device_uid() for fetching _UID in 2 places (Raag Jadav).
- Add context argument to acpi_dev_install_notify_handler() (Rafael
Wysocki).
- Clarify ACPI bus concepts in the ACPI device enumeration
documentation (Rafael Wysocki).
- Switch over the ACPI AC and ACPI PAD drivers to using the platform
driver interface which, is more logically consistent than binding a
driver directly to an ACPI device object, and clean them up (Michal
Wilczynski).
- Replace strncpy() in the PNP code with either memcpy() or strscpy()
as appropriate (Justin Stitt).
- Clean up coding style in pnp.h (GuoHua Cheng).
-----BEGIN PGP SIGNATURE-----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=p4Yo
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These fix issues, add new quirks, rearrange the IRQ override quirk
definitions, add new helpers and switch over code to using them,
rework a couple of interfaces to be more flexible, eliminate strncpy()
usage from PNP, extend the ACPI PCC mailbox driver and clean up code.
This is based on ACPI thermal driver changes that are present in the
thermal control updates for 6.7-rc1 pull request (they are depended on
by the ACPI utilities updates). However, the ACPI thermal driver
changes are not included in the list of specific ACPI changes below.
Specifics:
- Add symbol definitions related to CDAT to the ACPICA code (Dave
Jiang)
- Use the acpi_device_is_present() helper in more places and rename
acpi_scan_device_not_present() to be about enumeration (James
Morse)
- Add __printf format attribute to acpi_os_vprintf() (Su Hui)
- Clean up departures from kernel coding style in the low-level
interface for ACPICA (Jonathan Bergh)
- Replace strncpy() with strscpy() in acpi_osi_setup() (Justin Stitt)
- Fail FPDT parsing on zero length records and add proper handling
for fpdt_process_subtable() to acpi_init_fpdt() (Vasily Khoruzhick)
- Rework acpi_handle_list handling so as to manage it dynamically,
including size computation (Rafael Wysocki)
- Clean up ACPI utilities code so as to make it follow the kernel
coding style (Jonathan Bergh)
- Consolidate IRQ trigger-type override DMI tables and drop .ident
values from dmi_system_id tables used for ACPI resources management
quirks (Hans de Goede)
- Add ACPI IRQ override for TongFang GMxXGxx (Werner Sembach)
- Allow _DSD buffer data only for byte accessors and document the
_DSD data buffer GUID (Andy Shevchenko)
- Drop BayTrail and Lynxpoint pinctrl device IDs from the ACPI LPSS
driver, because it does not need them (Raag Jadav)
- Add acpi_backlight=vendor quirk for Toshiba Portégé R100 (Ondrej
Zary)
- Add "vendor" backlight quirks for 3 Lenovo x86 Android tablets
(Hans de Goede)
- Move Xiaomi Mi Pad 2 backlight quirk to its own section (Hans de
Goede)
- Annotate struct prm_module_info with __counted_by (Kees Cook)
- Fix AER info corruption in aer_recover_queue() when error status
data has multiple sections (Shiju Jose)
- Make APEI use ERST maximum execution time for slow devices (Jeshua
Smith)
- Add support for platform notification handling to the PCC mailbox
driver and modify it to support shared interrupts for multiple
subspaces (Huisong Li)
- Define common macros to use when referring to various bitfields in
the PCC generic communications channel command and status fields
and use them in some drivers (Sudeep Holla)
- Add EC GPE detection quirk for HP 250 G7 Notebook PC (Jonathan
Denose)
- Fix and clean up create_pnp_modalias() and create_of_modalias()
(Christophe JAILLET)
- Modify 2 pieces of code to use acpi_evaluate_dsm_typed() (Andy
Shevchenko)
- Define acpi_dev_uid_match() for matching _UID and use it in several
places (Raag Jadav)
- Use acpi_device_uid() for fetching _UID in 2 places (Raag Jadav)
- Add context argument to acpi_dev_install_notify_handler() (Rafael
Wysocki)
- Clarify ACPI bus concepts in the ACPI device enumeration
documentation (Rafael Wysocki)
- Switch over the ACPI AC and ACPI PAD drivers to using the platform
driver interface which, is more logically consistent than binding a
driver directly to an ACPI device object, and clean them up (Michal
Wilczynski)
- Replace strncpy() in the PNP code with either memcpy() or strscpy()
as appropriate (Justin Stitt)
- Clean up coding style in pnp.h (GuoHua Cheng)"
* tag 'acpi-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (54 commits)
ACPI: resource: Do IRQ override on TongFang GMxXGxx
perf: arm_cspmu: use acpi_dev_hid_uid_match() for matching _HID and _UID
ACPI: EC: Add quirk for HP 250 G7 Notebook PC
ACPI: x86: use acpi_dev_uid_match() for matching _UID
ACPI: utils: use acpi_dev_uid_match() for matching _UID
pinctrl: intel: use acpi_dev_uid_match() for matching _UID
ACPI: utils: Introduce acpi_dev_uid_match() for matching _UID
ACPI: sysfs: Clean up create_pnp_modalias() and create_of_modalias()
ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
ACPI: acpi_pad: Rename ACPI device from device to adev
ACPI: acpi_pad: Use dev groups for sysfs
ACPI: acpi_pad: Replace acpi_driver with platform_driver
ACPI: APEI: Use ERST timeout for slow devices
ACPI: scan: Rename acpi_scan_device_not_present() to be about enumeration
PNP: replace deprecated strncpy() with memcpy()
PNP: ACPI: replace deprecated strncpy() with strscpy()
perf: qcom: use acpi_device_uid() for fetching _UID
ACPI: sysfs: use acpi_device_uid() for fetching _UID
ACPI: scan: Use the acpi_device_is_present() helper in more places
ACPI: AC: Rename ACPI device from device to adev
...
Fix the following coccicheck warning:
drivers/i2c/busses/i2c-s3c2410.c:391:5-8: Unneeded variable: "ret".
Return "0" on line 552
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It adds ACPI device id for sc8180x platform, so that the devices can be
probed for ACPI boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use new helper acpi_use_parent_companion to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add kernel-doc for 'slave' and 'irq' in struct axxia_i2c_dev.
Drop kernel-doc notation ("/**") for static functions since they
are not usually documented with kernel-doc.
Prevents these kernel-doc warnings:
i2c-axxia.c:150: warning: Function parameter or member 'slave' not described in 'axxia_i2c_dev'
i2c-axxia.c:150: warning: Function parameter or member 'irq' not described in 'axxia_i2c_dev'
i2c-axxia.c:172: warning: Function parameter or member 'ns' not described in 'ns_to_clk'
i2c-axxia.c:172: warning: Function parameter or member 'clk_mhz' not described in 'ns_to_clk'
i2c-axxia.c:172: warning: No description found for return value of 'ns_to_clk'
i2c-axxia.c:271: warning: Function parameter or member 'idev' not described in 'axxia_i2c_empty_rx_fifo'
i2c-axxia.c:271: warning: No description found for return value of 'axxia_i2c_empty_rx_fifo'
i2c-axxia.c:303: warning: Function parameter or member 'idev' not described in 'axxia_i2c_fill_tx_fifo'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202310181049.Vo62moV1-lkp@intel.com/
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add missing description of the atomic boolean in struct stm32f7_i2c_dev.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Previously the duty cycle was divided equally into h_scl_l, t_scl_h.
This makes the low period of the SCL clock in Fast Mode is only 1.25us
which is way lower than the minimal value (1.3) specified in i2c
specification. In order to make sure t_scl_l, t_scl_h always fullfill
i2c specification, this commit calculates t_scl_l using this formula:
t_scl_l = clk_cycle *
((t_low_min + (scl_clock - t_low_min - t_high_min) / 2) / scl_clock)
where:
t_low_min is the minimal value of low period of the SCL clock in us;
t_high_min is the minimal value of high period of the SCL clock in us;
scl_clock is converted from SCL clock frequency into us.
Signed-off-by: Camel Guo <camel.guo@axis.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Now that the legacy eeprom driver was removed, the only remaining i2c
client driver with class SPD autodetection is jc42, and this driver
supports also class HWMON. Therefore we can remove class SPD from the
supported classes of the i801 adapter driver.
Legacy class-based instantiation shouldn't be used in new code, so I
think we can remove also the generic logic that ensures that supported
classes of parent and muxed adapters don't overlap.
Note: i801 parent supports just class HWMON now, and muxed childs
class SPD, so the supported classes don't overlap.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for atomic transfers using polling mode with interrupts
intentionally disabled. This removes the warning introduced by commit
63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
during system reboot and power-off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6b ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for atomic transfers using polling mode with interrupts
intentionally disabled to get rid of the warning introduced by commit
63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
during system reboot and power-off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implements the I2C function of Intel USB-I2C/GPIO/SPI adapter device
named "La Jolla Cove Adapter" (LJCA). It communicate with LJCA I2C
module with specific protocol through interfaces exported by LJCA
USB driver.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/1696833205-16716-3-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SMBus PCI ID on Intel Birch Stream SoC.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Main updates include:
1. Addition of support for Type 4 PCC subspace that enables platform
notification handling (Huisong Li).
2. Support for the shared interrupt amongst multiple PCC subspaces/
channels (Huisong Li).
3. Consolidation of PCC shared memory region command and status
bitfields definitions that were duplicated and scattered across
multiple PCC client drivers (Sudeep Holla).
-----BEGIN PGP SIGNATURE-----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=bZ1a
-----END PGP SIGNATURE-----
Merge tag 'acpi-pcc-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux
Merge ACPI PCC changes for v6.7 from Sudeep Holla:
"ACPI: PCC: Mailbox and generic updates for v6.7
Main updates include:
1. Addition of support for Type 4 PCC subspace that enables platform
notification handling (Huisong Li).
2. Support for the shared interrupt amongst multiple PCC subspaces/
channels (Huisong Li).
3. Consolidation of PCC shared memory region command and status
bitfields definitions that were duplicated and scattered across
multiple PCC client drivers (Sudeep Holla)."
* tag 'acpi-pcc-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
soc: kunpeng_hccs: Migrate to use generic PCC shmem related macros
hwmon: (xgene) Migrate to use generic PCC shmem related macros
i2c: xgene-slimpro: Migrate to use generic PCC shmem related macros
ACPI: PCC: Add PCC shared memory region command and status bitfields
mailbox: pcc: Support shared interrupt for multiple subspaces
mailbox: pcc: Add support for platform notification handling
Use the newly defined common and generic PCC shared memory region
related macros in this driver to replace the locally defined ones.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230927-pcc_defines-v2-2-0b8ffeaef2e5@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Return an error code if devm_reset_control_get_exclusive() fails.
The current code returns success.
Fixes: 0e864b552b ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-mv64xxx
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
`info.type` is expected to be NUL-terminated judging by its use in
`i2c_new_client_device()` wherein it is used to populate `client->name`:
| strscpy(client->name, info->type, sizeof(client->name));
NUL-padding is not required and even if it was, `client` is already
zero-initialized.
Considering the two points from above, a suitable replacement is
`strscpy` [2] due to the fact that it guarantees NUL-termination on the
destination buffer without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect name to be NUL-terminated based on its numerous uses with
functions that expect NUL-terminated strings.
For example in i2c-core-base.c +1533:
| dev_dbg(&adap->dev, "adapter [%s] registered\n", adap->name);
NUL-padding is not required as `adap` is already zero-alloacted with:
| adap = devm_kzalloc(&usbif->dev, sizeof(struct i2c_adapter), GFP_KERNEL);
With the above in mind, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The error paths for xiic_reinit() return negative values on failure
and 0 on success - this error message therefore is triggered on
_success_ rather than failure. Correct the condition so it's only
shown on failure as intended.
Fixes: 8fa9c93880 ("i2c: xiic: return value of xiic_reinit")
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
debugfs can handle error pointers in subsequent calls. So, remove the
error checks as suggested by kerneldoc of this function.
Reported-by: Minjie Du <duminjie@vivo.com>
Closes: http://patchwork.ozlabs.org/project/linux-i2c/patch/20230713101829.15548-1-duminjie@vivo.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With some new registers, SCL can be calculated to be closer to the
desired rate. Apply the new formula for R-Car Gen3 device types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Initially, we only needed a reset controller to make sure RXDMA works at
least once per transfer. Meanwhile, documentation has been updated. It
now says that a reset has to be performed prior every transaction, even
if it is non-DMA. So, make the reset controller a requirement instead of
being optional. And bail out if resetting fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C core ensures in i2c_smbus_xfer() that the I2C bus lock is held when
calling the smbus_xfer callback. That's i801_access() in our case.
I think it's safe in general to assume that the I2C bus lock is held
when the smbus_xfer callback is called.
Therefore I see no need to define an own mutex.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When entering the suspend callback, at first we should ensure that
transfers are finished and I2C core can't start further transfers.
Use i2c_mark_adapter_suspended() for this purpose, and complement it
with a call to i2c_mark_adapter_resumed() in the resume path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.
Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In few places relevant registers are reset to their initial value on
driver load. Factor this out to new helper i801_restore_regs to avoid
code duplication.
Even though no actual problems are known, this patch may contribute
to avoiding potential issues by:
- restoring register values also in the error path of i2c_add_adapter
- making restoring registers the last step (especially in i801_remove)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The DesignWare IP can be synthesized with the IC_EMPTYFIFO_HOLD_MASTER_EN
parameter.
In this case, when the TX FIFO gets empty and the last command didn't have
the STOP bit (IC_DATA_CMD[9]), the controller will hold SCL low until
a new command is pushed into the TX FIFO or the transfer is aborted.
When the controller is holding SCL low, it cannot be disabled.
The transfer must first be aborted.
Also, the bus recovery won't work because SCL is held low by the master.
Check if the master is holding SCL low in __i2c_dw_disable() before trying
to disable the controller. If SCL is held low, an abort is initiated.
When the abort is done, then proceed with disabling the controller.
This whole situation can happen for instance during SMBus read data block
if the slave just responds with "byte count == 0".
This puts the driver in an unrecoverable state, because the controller is
holding SCL low and the current __i2c_dw_disable() procedure is not
working. In this situation only a SoC reset can fix the i2c bus.
Co-developed-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Value comes from DT, so it could be 0. Unlikely, but could be.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It improves readability if we use the available helper.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of trying all values, we can actually compute it as the comment
suggests. It is unclear what the comment means with "involved", it works
nicely.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use proper types and spacing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Kernel functions goto somewhere on error conditions. Using goto for the
default path is irritating. Let's bail out on error instead and use a
proper retval.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:221: warning: Function parameter or
member 'rinfo' not described in 'cdns_i2c'
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171510.bKHBcZQW-lkp@intel.com/
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "i2c_mlxcpld" platform device is only instantiated on X86 systems
(through drivers/platform/x86/mlx-platform.c), or on ARM64 systems with
ACPI (through drivers/platform/mellanox/nvsw-sn2201.c). Hence further
restrict the dependency on ARM64 to ACPI, to prevent asking the user
about this driver when configuring an ARM64 kernel without ACPI support.
While at it, document in the Kconfig help text that the driver supports
ARM64/ACPI based systems, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
a lot of developers were on holidays (including myself) it was a good
timing to apply lots of cleanups which would normally cause merge
conflicts with other floating patches. Extra thanks go to Andi Shyti who
backed me up when I was on a four week hiatus. This is also the reason
that some patches were commited later than ideal.
-----BEGIN PGP SIGNATURE-----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=gpYJ
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
Change
if (IS_ERR(x)) { dev_err(...); return PTR_ERR(x); }
into
return dev_err_probe()
Also, return the correct error instead of hardcoding -ENODEV
This change has also the advantage of handling the -EPROBE_DEFER situation.
Signed-off-by: Yann Sionneau <yann@sionneau.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If pinctrl is not available (thus devm_pinctrl_get() returns NULL) then
recovery can't work, because we can't switch the I2C pins between the
I2C controller and GPIO. So, it is quite correct to print
"can't get pinctrl, bus recovery not supported" because the I2C bus
can't be recovered without pinctrl.
The PTR_ERR() is also fine - because if pinctrl is not present and
returns NULL, we'll end up returning zero, which is exactly what we
want.
However, open code that with a more accurate message will be more explicit
for NULL case when CONFIG_PINCTRL is not defined.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently if the SoC needs pinctrl to switch the SCL and SDA from the I2C
function to GPIO function, the recovery won't work.
scl-gpio = <>;
sda-gpio = <>;
Are not enough for some SoCs to have a working recovery.
Some need:
scl-gpio = <>;
sda-gpio = <>;
pinctrl-names = "default", "recovery";
pinctrl-0 = <&i2c_pins_hw>;
pinctrl-1 = <&i2c_pins_gpio>;
The driver was not filling rinfo->pinctrl with the device node
pinctrl data which is needed by generic recovery code.
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for extended length of read and write transactions.
New FPGA logic allows to increase size of the read and write
transactions length. This feature is verified through capability
register 'CPBLTY_REG'. Two bits 5 and 6 of the register are used for
length capability detection. Value '10' indicates support of extended
transaction length - 128 bytes for read transactions and 132 for write
transactions.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of a if condition with a line split, use the usual error
handling pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_clk_bulk_get_all() can return zero when no clocks are obtained.
Passing zero to dev_err_probe() is a success which is incorrect.
Fixes: 605efbf438 ("i2c: qcom-cci: Use dev_err_probe in probe function")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a10387280 ("i2c: iproc: add NIC I2C support")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "ret" variable is uninitialized. It was the "p2wi->rstc" variable
that was intended. We can also use the %pe string format to print the
error code name instead of just the number.
Fixes: 75ff8a340a ("i2c: sun6i-p2wi: Use devm_clk_get_enabled()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The controller may be shared with other port, for example the firmware.
Handle the interrupt from other sources will cause crash since some
data are not initialized. So only handle the interrupt of the driver's
transfer and discard others.
Fixes: d62fbdb99a ("i2c: add support for HiSilicon I2C controller")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230801124625.63587-1-yangyicong@huawei.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra processors prior to Tegra186 used APB DMA for I2C requiring
CONFIG_TEGRA20_APB_DMA=y while Tegra186 and later use GPC DMA requiring
CONFIG_TEGRA186_GPC_DMA=y.
The check for if the processor uses APB DMA is inverted and so the wrong
DMA config options are checked.
This means if CONFIG_TEGRA20_APB_DMA=y but CONFIG_TEGRA186_GPC_DMA=n
with a Tegra186 or later processor the driver will incorrectly think DMA is
enabled and attempt to request DMA channels that will never be availible,
leaving the driver in a perpetual EPROBE_DEFER state.
Fixes: 48cb6356fa ("i2c: tegra: Add GPCDMA support")
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Akhil R <akhilrajeev@nvidia.com>
Link: https://lore.kernel.org/r/fcfcf9b3-c8c4-9b34-2ff8-cd60a3d490bd@connecttech.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the driver fails to obtain a DMA channel, it will initiate cleanup
and try to release the DMA channel that couldn't be retrieved. This will
cause a crash because the cleanup will try to dereference an ERR_PTR()-
encoded error code.
However, there's nothing to clean up at this point yet, so we can avoid
this by simply resetting the DMA channel to NULL instead of storing the
error code.
Fixes: fcc8a89a1c ("i2c: tegra: Share same DMA channel for RX and TX")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 0daede80f8 ("i2c: designware: Convert driver to using regmap API")
changes the logic to validate the whole 32-bit return value of
DW_IC_DATA_CMD register instead of 8-bit LSB without reason.
Later, commit f53f15ba5a ("i2c: designware: Get right data length"),
introduced partial fix but not enough because the "tmp > 0" still test
tmp as 32-bit value and is wrong in case the IC_DATA_CMD[11] is set.
Revert the logic to just before commit 0daede80f8
("i2c: designware: Convert driver to using regmap API").
Fixes: f53f15ba5a ("i2c: designware: Get right data length")
Fixes: 0daede80f8 ("i2c: designware: Convert driver to using regmap API")
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-2-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On MX8X platforms, the default clock rate is 0 if without explicit
clock setting in dts nodes. I2c can't work when i2c peripheral clk
rate is 0.
Add a i2c peripheral clk rate check before configuring the clock
register. When i2c peripheral clk rate is 0 and directly return
-EINVAL.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Patch allows usb devices with multiple interfaces to use this driver without
this driver assuming all interfaces are i2c-tiny-usb.
Signed-off-by: Harry Geyer <harry.geyer@devtank.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230727162255.21551-1-harry.geyer@devtank.co.uk
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-10-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-9-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-8-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-7-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-6-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20230808012954.1643834-5-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-4-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230808012954.1643834-3-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230808012954.1643834-2-liaochang1@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/20230731112755.1943630-1-ruanjinjie@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When platform_get_irq() is called, the error message has been printed,
so it need not to call dev_err_probe() to print error.
As the comment of platform_get_irq() says, it returned non-zero value
when it succeeded, and it returned negative value when it failed.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230801134814.247782-1-wangzhu9@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
This is passing a NULL thread to request_threaded_irq(). So it's not
really a threaded IRQ at all. It's more readable to call request_irq()
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/fa375cc0-893a-4e64-8bf6-cc37f9ebecf5@moroto.mountain
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20230722115310.27681-5-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230722115310.27681-4-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230722115310.27681-3-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230722115310.27681-2-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
