Running i2c-detect currently produces an output akin to:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 08 -- 0a -- 0c -- 0e --
10: 10 -- 12 -- 14 -- 16 -- UU 19 -- 1b -- 1d -- 1f
20: -- 21 -- 23 -- 25 -- 27 -- 29 -- 2b -- 2d -- 2f
30: -- -- -- -- -- -- -- -- 38 -- 3a -- 3c -- 3e --
40: 40 -- 42 -- 44 -- 46 -- 48 -- 4a -- 4c -- 4e --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- 62 -- 64 -- 66 -- 68 -- 6a -- 6c -- 6e --
70: 70 -- 72 -- 74 -- 76 --
This happens because for an i2c_msg with a len of 0 the driver will
mark the transmission of the message as a success once the START has
been sent, without waiting for the devices on the bus to respond with an
ACK/NAK. Since i2cdetect seems to run in a tight loop over all addresses
the NAK is treated as part of the next test for the next address.
Delete the fast path that marks a message as complete when idev->msg_len
is zero after sending a START/RESTART since this isn't a valid scenario.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-outbid-encounter-b2e78b1cc707@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
At present, where repeated sends are intended to be used, the
i2c-microchip-core driver sends a stop followed by a start. Lots of i2c
devices must not malfunction in the face of this behaviour, because the
driver has operated like this for years! Try to keep track of whether or
not a repeated send is required, and suppress sending a stop in these
cases.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-football-composure-e56df2461461@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Compatible string "fsl,imx7d-i2c" is not exited at i2c-imx driver
compatible string table, at the result, "fsl,imx21-i2c" will be
matched, but it will cause erratum ERR007805 not be applied in fact.
So Add "fsl,imx7d-i2c" compatible string in i2c-imx driver to apply
the erratum ERR007805(https://www.nxp.com/docs/en/errata/IMX7DS_3N09P.pdf).
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
"fsl,imx7d-i2c" already is documented in binding doc. This erratum
fix has been included in imx6_i2c_hwdata and it is the same in all
I.MX6/7/8, so just reuse it.
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20241218044238.143414-1-carlos.song@nxp.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
A regression was introduced with the implementation of single-master
mode, preventing proper stop conditions from being generated. Devices
that require a valid stop condition, such as EEPROMs, fail to function
correctly as a result.
The issue only affects devices with the single-master property enabled.
This commit resolves the issue by re-enabling I2C bus busy bit (IBB)
polling for single-master mode when generating a stop condition. The fix
further ensures that the i2c_imx->stopped flag is cleared at the start
of each transfer, allowing the stop condition to be correctly generated
in i2c_imx_stop().
According to the reference manual (IMX8MMRM, Rev. 2, 09/2019, page
5270), polling the IBB bit to determine if the bus is free is only
necessary in multi-master mode. Consequently, the IBB bit is not polled
for the start condition in single-master mode.
Fixes: 6692694aca ("i2c: imx: do not poll for bus busy in single master mode")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241216151829.74056-1-eichest@gmail.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Various Dell laptops have an lis3lv02d freefall/accelerometer sensor.
The lis3lv02d chip has an interrupt line as well as an I2C connection to
the system's main SMBus.
The lis3lv02d is described in the ACPI tables by an SMO88xx ACPI device,
but the SMO88xx ACPI fwnodes are incomplete and only list an IRQ resource.
So far this has been worked around with some SMO88xx specific quirk code
in the generic i2c-i801 driver, but it is not necessary to handle the Dell
specific instantiation of i2c_client-s for SMO88xx ACPI devices there.
The kernel already instantiates platform_device-s for these with an
acpi:SMO88xx modalias. The drivers/platform/x86/dell/dell-smo8800.c
driver binds to this platform device but this only deals with
the interrupt resource. Add a drivers/platform/x86/dell/dell-lis3lv02d.c
which will matches on the same acpi:SMO88xx modaliases and move
the i2c_client instantiation from the generic i2c-i801 driver there.
Moving the i2c_client instantiation has the following advantages:
1. This moves the SMO88xx ACPI device quirk handling away from the generic
i2c-i801 module which is loaded on all Intel x86 machines to a module
which will only be loaded when there is an ACPI SMO88xx device.
2. This removes the duplication of the SMO88xx ACPI Hardware ID (HID) table
between the i2c-i801 and dell-smo8800 drivers.
3. This allows extending the quirk handling by adding new code and related
module parameters to the dell-lis3lv02d driver, without needing to modify
the i2c-i801 code.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20241209183557.7560-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514 ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The OF match table is not NULL-terminated.
Fix this by adding a sentinel to nmk_i2c_eyeq_match_table[].
Fixes: a0d15cc47f ("i2c: nomadik: switch from of_device_is_compatible() to of_match_device()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Since commit f63b94be69 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be69 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 35eba185fd ("i2c: designware: Calculate SCL timing parameter
for High Speed Mode") the SCL high period count and low period count for
high speed mode are calculated based on fixed tHIGH = 160 and tLOW = 120.
However, the set of two fixed values is only applicable to the combination
of hardware parameters IC_CAP_LOADING is 400 and IC_CLK_FREQ_OPTIMIZATION
is true. Outside of this combination, the SCL frequency may not reach
3.4 MHz because the fixed tHIGH and tLOW are not small enough.
If IC_CAP_LOADING is 400, it means the bus capacitance is 400pF;
Otherwise, 100 pF. If IC_CLK_FREQ_OPTIMIZATION is true, it means that the
hardware reduces its internal clock frequency by reducing the internal
latency required to generate the high period and low period of the SCL line.
Section 3.15.4.5 in DesignWare DW_apb_i2b Databook v2.03 says that when
IC_CLK_FREQ_OPTIMIZATION = 0,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 120 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 160 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
and section 3.15.4.6 says that when IC_CLK_FREQ_OPTIMIZATION = 1,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 160 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 120 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
In order to calculate more accurate SCL high period count and low period
count for high speed mode, two hardware parameters IC_CAP_LOADING and
IC_CLK_FREQ_OPTIMIZATION must be considered together. Since there're no
registers controlliing these these two hardware parameters, users can
declare them in the device tree so that the driver can obtain them.
Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
- BRCR value must go into the BRCR1 field when in high-speed mode.
It goes into BRCR2 otherwise.
- Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.
- Set SM properly in probe; previously it only checked STANDARD versus
FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.
- Remove all comment sections saying we only support low-speeds.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Current BRCR computation is:
brcr = floor(i2cclk / (clkfreq * div))
With brcr: "baud rate counter", an internal clock divider,
and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
and clkfreq: desired bus rate,
and div: speed-mode dependent divider (2 for standard, 3 otherwise).
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) = 4
and resulting bus rate = 48MHz / (4 * 3) = 4MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz
The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:
brcr = floor(i2cclk / (clkfreq * div)) + 1
If we redo the above examples:
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz
In kernel C code, floor(x) is DIV_ROUND_DOWN() and,
floor(x)+1 is DIV_ROUND_UP().
This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.
This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add EyeQ6H support to the nmk-i2c AMBA driver. It shares the same quirk
as EyeQ5: the memory bus only supports 32-bit accesses. Avoid writeb()
and readb() by reusing the same `priv->has_32b_bus` flag.
It does NOT need to write speed-mode specific value into a register;
therefore it does not depend on the mobileye,olb DT property.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Compatible-specific behavior is implemented using a if-condition on the
return value from of_device_is_compatible(), from probe. It does not
scale well when compatible number increases. Switch to using a match
table and a call to of_match_device().
We DO NOT attach a .of_match_table field to our amba driver, as we do
not use the table to match our driver to devices.
Sort probe variable declarations in reverse christmas tree to try and
introduce some logic into the ordering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Enable DWAPB I2C controller support on FUJITSU-MONAKA.
This will be used in the FUJITSU-MONAKA server scheduled
for shipment in 2027.
The DSDT information obtained when verified using an
in-house simulator is presented below.
Device (SMB0)
{
Name (_HID, "FUJI200B") // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
...
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite,
0x2A4B0000, // Address Base
0x00010000, // Address Length
)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
{
0x00000159,
}
})
...
}
The expression SMB0 is used to indicate SMBus HC#0,
a string of up to four characters.
Created the SMB0 object according to the following
specifications:
ACPI Specification
13.2. Accessing the SMBus from ASL Code
https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/13_ACPI_System_Mgmt_Bus_Interface_Spec/accessing-the-smbus-from-asl-code.html
IPMI Specification
Example 4: SSIF Interface(P574)
https://www.intel.co.jp/content/www/jp/ja/products/docs/servers/ipmi/ipmi-second-gen-interface-spec-v2-rev1-1.html
Signed-off-by: Yoshihiro Furudera <fj5100bi@fujitsu.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
There's no reason for this driver to use OF-specific property helpers.
Drop the last one in favor of the generic variant and no longer include
of.h.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
i2c-core (Wolfram)
- drivers can now use a GPIO as a side channel for SMBus Alerts
using a generic binding
- regular stuff like mem leak fix, Makefile maintenance...
i2c-host updates (Andi)
Major Improvements and Refactoring:
- All controllers using the 'remove_new' callback have been
reverted to use the 'remove' callback.
- Intel SCH controller underwent significant refactoring,
this brings love and a modern look to the driver.
- PIIX4 driver refactored to enable usage by other drivers
(e.g., AMD ASF).
- iMX/MXC improved message handling to reduce protocol overhead:
Refactored DMA/non-DMA read/write and bus polling mechanisms
to achieve this.
- ACPI documentation for PIIX4.
New Features:
- i2c-cadence added support for atomic transfers.
- Qualcomm CII added support for a 32MHz serial engine clock.
Deprecated Features:
- Dropped outdated support for AMD756 S4882 and NFORCE2 S4985. If
somebody misses this, Jean will rewrite support using the proper
i2c mux framework.
New Hardware Support:
- Added support for:
- Intel Panther Lake (new ID)
- AMD ASF (new driver)
- S32G2/S32G3 SoCs (new ID)
- Realtek RTL I2C Controller (new driver)
- HJMC01 DesignWare ACPI HID (new ID)
- PIC64GX to Microchip Core (new ID)
- Qualcomm SDM670 to Qualcomm CCI (new ID)
at24 updates (Bartosz)
- add support for the lockable page on ST M24256E
-----BEGIN PGP SIGNATURE-----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=lrn5
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core:
- drivers can now use a GPIO as a side channel for SMBus Alerts using
a generic binding
- regular stuff like mem leak fix, Makefile maintenance...
Host improvements and refactoring:
- All controllers using the 'remove_new' callback have been reverted
to use the 'remove' callback
- Intel SCH controller underwent significant refactoring, this brings
love and a modern look to the driver
- PIIX4 driver refactored to enable usage by other drivers (e.g., AMD
ASF)
- iMX/MXC improved message handling to reduce protocol overhead:
Refactored DMA/non-DMA read/write and bus polling mechanisms to
achieve this.
- ACPI documentation for PIIX4
New host features:
- i2c-cadence support for atomic transfers
- Qualcomm CII support for a 32MHz serial engine clock
Deprecated features:
- Dropped outdated support for AMD756 S4882 and NFORCE2 S4985. If
somebody misses this, Jean will rewrite support using the proper
i2c mux framework.
New hardware IDs for existing drivers:
- Intel Panther Lake
- S32G2/S32G3 SoCs
- HJMC01 DesignWare ACPI HID
- PIC64GX to Microchip Core
- Qualcomm SDM670 to Qualcomm CCI
New drivers:
- AMD ASF
- Realtek RTL I2C Controller
at24 updates:
- add support for the lockable page on ST M24256E"
* tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (59 commits)
docs: i2c: piix4: Add ACPI section
i2c: Add driver for the RTL9300 I2C controller
i2c: qcom-cci: Remove unused struct member cci_clk_rate
dt-bindings: i2c: Add Realtek RTL I2C Controller
i2c: busses: Use *-y instead of *-objs in Makefile
i2c: imx: add support for S32G2/S32G3 SoCs
dt-bindings: i2c: imx: add SoC specific compatible strings for S32G
i2c: qcom-cci: Remove the unused variable cci_clk_rate
i2c: Drop legacy muxing pseudo-drivers
i2c: imx: prevent rescheduling in non dma mode
i2c: imx: separate atomic, dma and non-dma use case
i2c: imx: do not poll for bus busy in single master mode
i2c: designware: Add a new ACPI HID for HJMC01 I2C controller
i2c: qcom-geni: Keep comment why interrupts start disabled
dt-bindings: i2c: microchip: corei2c: Add PIC64GX as compatible with driver
i2c: designware: constify abort_sources
i2c: Switch back to struct platform_driver::remove()
i2c: qcom-geni: Support systems with 32MHz serial engine clock
i2c: qcom-cci: Stop complaining about DT set clock rate
dt-bindings: i2c: qcom-cci: Document SDM670 compatible
...
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for consistency with
other places
- modify the behavior of the sysfs interface by no longer exporting lines that
are named inside the driver code or board files with the sysfs links bearing
the line names as this has for many years been largely unused due to the
prevalence of DT, ACPI and firmware nodes over board files and made the API
inconsistent
- for GPIO interrupt providers: free irqs that are still requested by users
when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested, released,
reconfigured) triggered from the kernel as well (until now we'd only do
this for changes triggered from user-space)
- to that end: modify the internal workings of the notification mechanism by
switching to an atomic notifier which allows us to send events from atomic
context
- also to that end store the debounce period in the GPIO descriptor struct
and not in the character device context struct
- while at it, also cover the corner-case of users introducing changes over
sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to user-space as it
can still request them as GPIOs
New drivers:
- add a driver for the GPIO functionality of the MFD Congatec Board Controller
- add a driver for the PolarFire GPIO controller
- add a driver supporting the GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones across
many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci, ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or entirely
remove the driver's remove() callback (grgpio, amdpt, menz127, max730x,
ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid some
line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the fwnode
on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby, xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the conversion to
remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop this
deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in gpiolib-of
and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools
-----BEGIN PGP SIGNATURE-----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=ON7q
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"Three new drivers, support for some new models in existing ones and
lots of various tweaks and improvements across the board (switching to
using recommended APIs, code shrink and simplification, etc.).
Also a new feature in the character device uAPI where we now notify
the user-space about changes triggered by in-kernel users as well, not
only when they were done by other user-space agents.
Summary:
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO
descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for
consistency with other places
- modify the behavior of the sysfs interface by no longer exporting
lines that are named inside the driver code or board files with the
sysfs links bearing the line names as this has for many years been
largely unused due to the prevalence of DT, ACPI and firmware nodes
over board files and made the API inconsistent
- for GPIO interrupt providers: free irqs that are still requested by
users when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested,
released, reconfigured) triggered from the kernel as well (until
now we'd only do this for changes triggered from user-space)
- to that end: modify the internal workings of the notification
mechanism by switching to an atomic notifier which allows us to
send events from atomic context
- also to that end store the debounce period in the GPIO descriptor
struct and not in the character device context struct
- while at it, also cover the corner-case of users introducing
changes over sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to
user-space as it can still request them as GPIOs
New drivers:
- GPIO part of the MFD Congatec Board Controller
- PolarFire GPIO controller
- GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones
across many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci,
ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or
entirely remove the driver's remove() callback (grgpio, amdpt,
menz127, max730x, ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid
some line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the
fwnode on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby,
xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and
gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the
conversion to remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop
this deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in
gpiolib-of and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to
gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools"
* tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (98 commits)
gpio: tegra186: Allow to enable driver on Tegra234
gpio: grgpio: Add NULL check in grgpio_probe
tools: gpio: Fix several incorrect format specifiers
gpio: mpfs: add CoreGPIO support
gpio: rockchip: support new version GPIO
gpio: rockchip: change the GPIO version judgment logic
gpio: rockchip: explan the format of the GPIO version ID
gpiolib: cdev: use !mem_is_zero() instead of memchr_inv(s, 0, n)
MAINTAINERS: add gpio driver to PolarFire entry
gpio: Get rid of GPIOF_ACTIVE_LOW
USB: gadget: pxa27x_udc: Avoid using GPIOF_ACTIVE_LOW
pcmcia: soc_common: Avoid using GPIOF_ACTIVE_LOW
leds: gpio: Avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys_polled - avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys - avoid using GPIOF_ACTIVE_LOW
gpio: Use of_property_present() for non-boolean properties
gpio: mpfs: add polarfire soc gpio support
gpio: altera: Drop legacy-of-mm-gpiochip.h header
gpio: pcie-idio-24: Replace deprecated PCI functions
gpio: pci-idio-16: Replace deprecated PCI functions
...
Add support for the I2C controller on the RTL9300 SoC. There are two I2C
controllers in the RTL9300 that are part of the Ethernet switch register
block. Each of these controllers owns a SCL pin (GPIO8 for the fiorst
I2C controller, GPIO17 for the second). There are 8 possible SDA pins
(GPIO9-16) that can be assigned to either I2C controller. This
relationship is represented in the device tree with a child node for
each SDA line in use.
This is based on the openwrt implementation[1] but has been
significantly modified
[1] - https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-5.15/drivers/i2c/busses/i2c-rtl9300.c
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The removal of the supply clock rate check implies a need to remove
some unnecessary left-over data from the driver as well.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
While at it, fix an obvious typo in help section of the Kconfig.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some S32G2/S32G3 SoC I2C particularities exist
such as different <clock divider, register value> pairs.
Those are addressed by adding specific S32G2 and S32G3
compatible strings.
Co-developed-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Signed-off-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Variable cci_clk_rate is not effectively used, so delete it.
drivers/i2c/busses/i2c-qcom-cci.c:526:16: warning: variable ‘cci_clk_rate’ set but not used.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11532
Fixes: 8284750a18 ("i2c: qcom-cci: Stop complaining about DT set clock rate")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The i2c-amd756-s4882 and i2c-nforce2-s4985 muxing pseudo-drivers were
written at a time when the i2c core did not support muxing. They are
essentially board-specific hacks. If we had to add support for these
boards today, we would implement it in a completely different way.
These Tyan server boards are 19 years old by now, so I very much doubt
any of these is still running today. So let's just drop this clumsy
code. If anyone really still needs this support and complains, I'll
rewrite it in a proper way on top of i2c-mux.
This also fixes the following warnings:
drivers/i2c/busses/i2c-amd756.c:286:20: warning: symbol 'amd756_smbus' was not declared. Should it be static?
drivers/i2c/busses/i2c-nforce2.c:123:20: warning: symbol 'nforce2_smbus' was not declared. Should it be static?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We are experiencing a problem with the i.MX I2C controller when
communicating with SMBus devices. We are seeing devices time-out because
the time between sending/receiving two bytes is too long, and the SMBus
device returns to the idle state. This happens because the i.MX I2C
controller sends and receives byte by byte. When a byte is sent or
received, we get an interrupt and can send or receive the next byte.
The current implementation sends a byte and then waits for an event
generated by the interrupt subroutine. After the event is received, the
next byte is sent and we wait again. This waiting allows the scheduler
to reschedule other tasks, with the disadvantage that we may not send
the next byte for a long time because the send task is not immediately
scheduled. For example, if the rescheduling takes more than 25ms, this
can cause SMBus devices to timeout and communication to fail.
This patch changes the behavior so that we do not reschedule the
send/receive task, but instead send or receive the next byte in the
interrupt subroutine. This prevents rescheduling and drastically reduces
the time between sending/receiving bytes. The cost in the interrupt
subroutine is relatively small, we check what state we are in and then
send/receive the next byte. Before we had to call wake_up, which is even
less expensive. However, we also had to do some scheduling, which
increased the overall cost compared to the new solution. The wake_up
function to wake up the send/receive task is now only called when an
error occurs or when the transfer is complete.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Separate the atomic, dma and non-dma use case as a preparation step for
moving the non-dma use case to the isr to avoid rescheduling while a
transfer is in progress.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
According to the i.MX8M Mini reference manual chapter "16.1.4.2
Generation of Start" it is only necessary to poll for bus busy and
arbitration lost in multi master mode. This helps to avoid rescheduling
while the i2c bus is busy and avoids SMBus devices to timeout. For
backward compatibility, the single-master property needs to be
explicitly set to disable the bus busy polling.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Define a new ACPI HID for HJMC01
Signed-off-by: Hunter Yu <hunter.yu@hj-micro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The to-be-fixed commit rightfully reduced a race window, but also
removed a comment which is still helpful after the fix. Bring the
comment back.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We never modify abort_sources, mark it as const.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/i2c to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In existing socs, I2C serial engine is sourced from XO (19.2MHz).
Where as in IPQ5424, I2C serial engine is sourced from GPLL0 (32MHz).
The existing map table is based on 19.2MHz. This patch incorporates
the clock map table to derive the SCL clock from the 32MHz source
clock frequency.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
It is common practice in the downstream and upstream CCI dt to set CCI
clock rates to 19.2 MHz. It appears to be fairly common for initial code to
set the CCI clock rate to 37.5 MHz.
Applying the widely used CCI clock rates from downstream ought not to cause
warning messages in the upstream kernel where our general policy is to
usually copy downstream hardware clock rates across the range of Qualcomm
drivers.
Drop the warning it is pervasive across CAMSS users but doesn't add any
information or warrant any changes to the DT to align the DT clock rate to
the bootloader clock rate.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/linux-arm-msm/20240824115900.40702-1-bryan.odonoghue@linaro.org
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
If not clearing the BB (bus busy) condition in the BER (bus error)
interrupt, the driver causes a timeout and hence the i2c core
doesn't do the i2c transfer retry but returns the driver's return
value to the upper layer instead.
Clear the BB condition in the BER interrupt and a software flag is
used. The driver does an i2c recovery without causing the timeout
if the flag is set.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Originally the driver uses the XMIT bit in SMBnST register to decide
the upcoming i2c transaction. If XMIT bit is 1, then it will be an i2c
write operation. If it's 0, then a read operation will be executed.
In slave mode the XMIT bit can simply be used directly to set the state.
XMIT bit can be used as an indication to the current state of the state
machine during slave operation. (meaning XMIT = 1 during writing and
XMIT = 0 during reading).
In master operation XMIT is valid only if there are no bus errors.
For example: in a multi master where the same module is switching from
master to slave at runtime, and there are collisions, the XMIT bit
cannot be trusted.
However the maser already "knows" what the bus state is, so this bit
is not needed and the driver can just track what it is currently doing.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The len variable is not initialized, which may cause the for loop to
behave unexpectedly.
Fixes: 9b25419ad3 ("i2c: amd-asf: Add routine to handle the ASF slave process")
Signed-off-by: Qianqiang Liu <qianqiang.liu@163.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Fix spelling and other issues, such as kernel-doc reported about,
in the comments. While at it, fix some indentation issues as well.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently the PCI glue driver uses sda_hold variable name, while
the rest of the driver use sda_hold_time. This makes things harder
to grep. Use sda_hold_time variable name everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The 'cond' parameter is not being used (always default, hence drop it
and hence make it consistent with i2c_dw_scl_lcnt().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use temporary variable for struct device to make code neater.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To ensure successive interrupts upon packet reception, it is necessary to
clear the remote IRR bit by writing the interrupt number to the EOI
register. The base address for this operation is provided by the BIOS and
retrieved by the driver by traversing the ASF object's namespace.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add support for handling ASF slave process events as described in the AMD
ASF databook. This involves implementing the correct programming sequence
to manage each ASF packet appropriately.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Implement the i2c_algorithm operations to enable support for AMD ASF
(Alert Standard Format) with SMBus. This enhancement includes:
- Adding functionality to identify and select the supported ASF functions.
- Implementing mechanisms for registering and deregistering I2C slave
devices.
- Providing support for data transfer operations over ASF.
Additionally, include a 'select' Kconfig entry as the current patch
utilizes .reg_slave() and .unreg_slave() callbacks, which are controlled
by CONFIG_I2C_SLAVE.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The AMD ASF controller is presented to the operating system as an ACPI
device. The AMD ASF driver can use ACPI to obtain information about the
ASF controller's attributes, such as the ASF address space and interrupt
number, and to handle ASF interrupts.
Currently, the piix4 driver assumes that a specific port address is
designated for AUX operations. However, with the introduction of ASF, the
same port address may also be used by the ASF controller. Therefore, a
check needs to be added to ensure that if ASF is advertised and enabled in
ACPI, the AUX port should not be configured.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Export the following i2c_piix4 driver functions as a library so that the
AMD ASF driver can utilize these core functionalities from the i2c_piix4
driver:
- piix4_sb800_region_request(): Request access to a specific SMBus region
on the SB800 chipset.
- piix4_sb800_region_release(): Release the previously requested SMBus
region on the SB800 chipset.
- piix4_transaction(): Handle SMBus transactions between the SMBus
controller and connected devices.
- piix4_sb800_port_sel(): Select the appropriate SMBus port on the SB800
chipset.
By making these functions available as a library, enable the AMD ASF
driver to leverage the established mechanisms in the i2c_piix4 driver,
promoting code reuse and consistency across different drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add a separate header file to relocate the common code from the i2c_piix4
driver, allowing the AMD ASF driver to utilize the same code.
Update the MAINTAINERS file to include information about the new common
header file.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently, `piix4_transaction()` accepts only one parameter, which is the
`i2c_adapter` information. This approach works well as long as SB800 SMBus
port accesses are confined to the piix4 driver. However, with the
implementation of a separate ASF driver and the varying address spaces
across drivers, it is necessary to change the function parameter list of
`piix4_transaction()` to include the port address. This modification
allows other drivers that use piix4 to pass the specific port details they
need to operate on.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Convert existing descriptions to kernel-doc format and unify
the rest of the comments to follow the modern style.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Octal permissions are preferred over the symbolics ones
for readbility. This ceases warning message pointed by checkpatch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There are two different names used for the variable that holds
an error code. Unify to use one variant in all cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Simplify the code by using read_poll_timeout().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce a temporary variable to hold a device pointer.
It can be utilized in the ->probe() and save a bit of LoCs.
To make it consistent, rename currently used dev to pdev.
While at it, convert the only error message to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Switch from i2c_add_adapter() to resource managed devm_i2c_add_adapter()
for matching rest of driver initialization, and more concise code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use custom private data structure instead of global variables.
With that, remove not anymore true comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use modern string_choices API instead of manually determining the
output using ternary operator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There are a lot of messaging calls that use global variable of
struct i2c_adapter. Instead, to make code better and flexible
for further improvements, pass the pointer to the actual adapter
used for transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Rework the read and write code paths in the driver to support operation
in atomic contexts in master mode. This change does not apply to slave
mode because there is no way to handle interruptions in that context.
Adjust the message timeout to include some extra time. For non-atomic
contexts, 500 ms is added to the timeout. For atomic contexts,
2000 ms is added because transfers happen in polled mode, requiring
more time to account for the polling overhead.
Similar changes have been implemented in other drivers, including:
commit 3a5ee18d2a ("i2c: imx: implement master_xfer_atomic callback")
commit 445094c8a9 ("i2c: exynos5: add support for atomic transfers")
commit ede2299f71 ("i2c: tegra: Support atomic transfers")
commit fe402bd090 ("i2c: meson: implement the master_xfer_atomic
callback")
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The cdns_i2c_master_xfer function has been refactored to separate
the common code. This change facilitates better support for atomic
mode operations by isolating the shared logic.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When the Tx FIFO is empty and the last command has no STOP bit
set, the master holds SCL low. If I2C_DYNAMIC_TAR_UPDATE is not
set, BIT(13) MST_ON_HOLD of IC_RAW_INTR_STAT is not enabled,
causing the __i2c_dw_disable() timeout. This is quite similar to
commit 2409205acd ("i2c: designware: fix __i2c_dw_disable() in
case master is holding SCL low"). Also check BIT(7)
MST_HOLD_TX_FIFO_EMPTY in IC_STATUS, which is available when
IC_STAT_FOR_CLK_STRETCH is set.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Co-developed-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Signed-off-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Co-developed-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Liu Peibao <loven.liu@jaguarmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add i2c support for the Congatec Board Controller.
The Board Controller has two i2c busses, a General Purpose bus and a Power
Management bus.
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20241001-congatec-board-controller-v3-3-39ceceed5c47@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
i2c-host fixes (from Andi)
In the stm32f7 a potential deadlock is fixed during runtime
suspend and resume.
-----BEGIN PGP SIGNATURE-----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=BsZQ
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
- Fix potential deadlock during runtime suspend and resume (stm32f7)
* tag 'i2c-for-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
In case there is any sort of clock controller attached to this I2C bus
controller, for example Versaclock or even an AIC32x4 I2C codec, then
an I2C transfer triggered from the clock controller clk_ops .prepare
callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex.
This is because the clock controller first grabs the prepare_lock mutex
and then performs the prepare operation, including its I2C access. The
I2C access resumes this I2C bus controller via .runtime_resume callback,
which calls clk_prepare_enable(), which attempts to grab the prepare_lock
mutex again and deadlocks.
Since the clock are already prepared since probe() and unprepared in
remove(), use simple clk_enable()/clk_disable() calls to enable and
disable the clock on runtime suspend and resume, to avoid hitting the
prepare_lock mutex.
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 4e7bca6fc0 ("i2c: i2c-stm32f7: add PM Runtime support")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 36ecbcab84 ("i2c: xiic: Implement power management")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The KEBA I2C controller is only present on KEBA PLC devices. Hence add
a dependency on KEBA_CP500, to prevent asking the user about this driver
when configuring a kernel without KEBA CP500 system FPGA support.
Fixes: c7e08c816c ("i2c: keba: Add KEBA I2C controller support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Gerhard Engleder <eg@keba.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
ACPI boot does not provide clocks and regulators, but instead, provides
the PCLK rate directly, and enables the clock in firmware. So deal
gracefully with this.
Fixes: 55750148e5 ("i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()")
Cc: stable@vger.kernel.org # v6.10+
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
It was observed that issuing the ABORT bit (IC_ENABLE[1]) will not
work when IC_ENABLE is already disabled.
Check if the ENABLE bit (IC_ENABLE[0]) is disabled when the controller
is holding SCL low. If the ENABLE bit is disabled, the software needs
to enable it before trying to issue the ABORT bit. otherwise,
the controller ignores any write to ABORT bit.
These kernel logs show up whenever an I2C transaction is
attempted after this failure.
i2c_designware e95e0000.i2c: timeout waiting for bus ready
i2c_designware e95e0000.i2c: timeout in disabling adapter
The patch fixes the issue where the controller cannot be disabled
while SCL is held low if the ENABLE bit is already disabled.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Signed-off-by: Kimriver Liu <kimriver.liu@siengine.com>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C core
========
After 15 years of deprecation, the I2C_COMPAT symbol has finally been
removed. Also client addresses are now locked during initialization to
prevent race conditions between different kinds of instantiation. Scoped
foreach OF child loops are now used. And the testunit has received some
cleanups and documentation improvements as well as two new tests, one
for repeated start and one for triggering SMBusAlert interrupts.
I2C host drivers
================
The DesignWare and the Renesas I2C drivers have received most of
the changes in this pull request.
The first has has undergone through a series of cleanups that
have been sent to the mailing list a year ago for the first time
and finally get merged in this pull request. They are many, from
typos (e.g. i2/i2c), to cosmetics, to refactoring (e.g. move
inline functions to librarieas) and many others.
Besides that, all the DesignWare Kconfig options have been
grouped under the I2C_DESIGNWARE_CORE and this required some
adaptation in many of the kernel configuration files for
different arm and mips boards.
Follows the list of the rest of the changes grouped by type of
change.
Cleanups
--------
The Qualcomm Geni platform improves the exit path in the runtime
resume function.
The Intel LJCA driver loses "target_addr" parameter in
ljca_i2c_stop() because it was unused.
The MediaTek controller intializes the restart_flag in the
transfer function using the ternary conditional operator ("? :")
instead of initializing it in different parts.
Constified a few global data structures in the virtio driver.
The Renesas driver simplifies the bus speed handling in the init
function making it more readable.
Improved an if/else statement in probe function of the Renesas
R-Car driver.
The iMX/MXC driver switches to using the RUNTIME_PM_OPS() instead
of SET_RUNTIME_PM_OPS().
Still in the iMX/MXC driver a comma ',' has been replaced by a
semicolon ';', while in different drivers the ',' has been
removed from the '{ }' delimiters.
Finally three devm_clk_get_enabled() have been used to simplify
the devm_clk_get/clk_prepare_enable tuple in the Renesas EMEV2,
Ingenic and MPC drivers.
Refactors
---------
The Nuvoton fixes a potential out of boundary array access. This
is not a bug fix because the issue could never occur due to
hardware not having the properties listed in the array. The
change makes the driver more future proof and, at the same time,
silences code analyzers.
Improvements
------------
The Renesas I2C (riic) driver undergoes several patches improving
the runtime power management handling.
The Intel i801 driver uses a more descriptive adapter's name to
show the presence of the IDF feature.
In the Intel Denverton (ismt) adapter the pending transactions
are killed when irq's can't complete their handling, triggering a
timeout. This could have been considered as a bug fix, but
because, standing to Vasily, it's very sporadic, I preferred
considering the patch rather as an improvement.
New Feature
-----------
The Renesas I2C (riic) driver now supports the fast mode plus.
New support
-----------
Added support for:
- Renesas R9A08G045
- Rockchip RK3576
- KEBA I2C
- Theobroma Systems Mule Multiplexer.
The Keba comes with a new driver, i2c-keba.c.
The Mule is an i2c multiplexer and it also comes with a new
driver, mux/i2c-mux-mule.c.
Core patch
----------
This pull request includes also a patch in the I2C framework, in
i2c-core-base.c where the runtime PM functions have been replaced
in order to allow to be accessed during the device add.
Devicetree
----------
Some cleanups in the devicetree, as well. nVidia and Qualcomm
bindings improve their "if:then:" blocks. While the aspeed
binding loses the "multi-master" property because it was
redundant.
The i2c-sprd binding has been converted to YAML.
AT24 updates
============
- document a new model from giantec in DT bindings
-----BEGIN PGP SIGNATURE-----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=DTNY
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C core:
- finally remove the I2C_COMPAT symbol after 15 years of deprecation
- lock client addresses during initialization to prevent race
conditions between different kinds of instantiation
- use scoped foreach OF child loops
- testunit cleanups and documentation improvements, as well as two
new tests, one for repeated start and one for triggering SMBusAlert
interrupts
I2C host drivers:
- DesignWare and Renesas I2C driver updates.
The first has has undergone through a series of cleanups that have
been sent to the mailing list a year ago for the first time and
finally get merged in this pull request. They are many, from typos
(e.g. i2/i2c), to cosmetics, to refactoring (e.g. move inline
functions to librarieas) and many others.
- all the DesignWare Kconfig options have been grouped under the
I2C_DESIGNWARE_CORE and this required some adaptation in many of
the kernel configuration files for different arm and mips boards
Cleanups:
- improve the exit path in the runtime resume function for the
Qualcomm Geni platform
- get rid of the unused "target_addr" parameter in the Intel LJCA
driver
- intialize the restart_flag in the MediaTek controller in one single
place
- constify a few global data structures in the virtio driver
- simplify the bus speed handling in the Renesas driver init function
making it more readable
- improved probe function of the Renesas R-Car driver
- switch the iMX/MXC driver to use RUNTIME_PM_OPS() instead of
SET_RUNTIME_PM_OPS()
- iMX/MXC driver cleanups
- use devm_clk_get_enabled() to simplify the Renesas EMEV2, Ingenic
and MPC drivers
Refactoring:
- Fix a potential out of boundary array access in the Nuvoton driver.
This is not a bug fix because the issue could never occur due to
hardware not having the properties listed in the array. The change
makes the driver more future proof and, at the same time, silences
code analyzers.
Improvements:
- several patches improving the runtime power management handling of
the Renesas I2C (riic) driver
- use a more descriptive adapter name in the Intel i801 driver to
show the presence of the IDF feature
- kill pending transactions when irq's can't complete their handling
in the Intel Denverton (ismt) driver, triggering a timeout
New Feature:
- support fast mode plus in the Renesas I2C (riic) driver
New support:
- Added support for:
- Renesas R9A08G045
- Rockchip RK3576
- KEBA I2C
- Theobroma Systems Mule Multiplexer.
- new i2c-keba.c driver
- new driver for The Mule i2c multiplexer
Core I2C framework:
- move runtime PM functions in order to allow them to be accessed
during device add
Devicetree:
- nVidia and Qualcomm binding improvements
- get rid of redundant "multi-master" property in the aspeed binding
- convert i2c-sprd binding to YAML
AT24 updates:
- document a new model from giantec in DT bindings"
* tag 'i2c-for-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
i2c: designware: Use pci_get_drvdata()
i2c: designware: Propagate firmware node
i2c: designware: Uninline i2c_dw_probe()
i2c: ljca: Remove unused "target_addr" parameter
i2c: keba: Add KEBA I2C controller support
i2c: i801: Use a different adapter-name for IDF adapters
i2c: core: Setup i2c_adapter runtime-pm before calling device_add()
dt-bindings: i2c: i2c-sprd: convert to YAML
i2c: ismt: kill transaction in hardware on timeout
i2c: designware: Group all DesignWare drivers under a single option
net: txgbe: Fix I2C Kconfig dependencies
RISC-V: configs: enable I2C_DESIGNWARE_CORE with I2C_DESIGNWARE_PLATFORM
mips: configs: enable I2C_DESIGNWARE_CORE with I2C_DESIGNWARE_PLATFORM
arm64: defconfig: enable I2C_DESIGNWARE_CORE with I2C_DESIGNWARE_PLATFORM
ARM: configs: enable I2C_DESIGNWARE_CORE with I2C_DESIGNWARE_PLATFORM
ARC: configs: enable I2C_DESIGNWARE_CORE with I2C_DESIGNWARE_PLATFORM
i2c: virtio: Constify struct i2c_algorithm and struct virtio_device_id
i2c: rcar: tidyup priv->devtype handling on rcar_i2c_probe()
i2c: imx: Convert comma to semicolon
i2c: jz4780: Use devm_clk_get_enabled() helpers
...
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Cc: <stable@vger.kernel.org> # v4.19+
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In accordance with the existing comment and code analysis
it is quite likely that there is a missed 'else' when adapter
times out. Add it.
Fixes: 5bc1200852 ("i2c: Add Intel SCH SMBus support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In the event that the I2C bus was powered down when the I2C controller
driver loads, or some spurious pulses occur on the I2C bus, it's
possible that the controller detects a spurious I2C "start" condition.
In this situation it may continue to report the bus is busy indefinitely
and block the controller from working.
The "single-master" DT flag can be specified to disable bus busy checks
entirely, but this may not be safe to use in situations where other I2C
masters may potentially exist.
In the event that the controller reports "bus busy" for too long when
starting a transaction, we can try reinitializing the controller to see
if the busy condition clears. This allows recovering from this scenario.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Frequently an I2C write will be followed by a read, such as a register
address write followed by a read of the register value. In this driver,
when the TX FIFO half empty interrupt was raised and it was determined
that there was enough space in the TX FIFO to send the following read
command, it would do so without waiting for the TX FIFO to actually
empty.
Unfortunately it appears that in some cases this can result in a NAK
that was raised by the target device on the write, such as due to an
unsupported register address, being ignored and the subsequent read
being done anyway. This can potentially put the I2C bus into an
invalid state and/or result in invalid read data being processed.
To avoid this, once a message has been fully written to the TX FIFO,
wait for the TX FIFO empty interrupt before moving on to the next
message, to ensure NAKs are handled properly.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When the i2c bus recovery occurs, driver will send i2c stop command
in the scl low condition. In this case the sw state will still keep
original situation. Under multi-master usage, i2c bus recovery will
be called when i2c transfer timeout occurs. Update the stop command
calling with aspeed_i2c_do_stop function to update master_state.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Propagate firmware node by using a specific API call, i.e. device_set_node().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Since i2c_dw_probe() is going to be extended, uninline it to reduce
the noise in the common header.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The stop command doesn't use any address on the target:
w_packet->data[0] = 0;
and indeed the targed_addr parameter was unused. Remove it.
Cc: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The KEBA I2C controller is found in the system FPGA of KEBA PLC devices.
It is used to connect EEPROMs and hardware monitoring chips. The
It is a simple I2C controller with a fixed bus speed of 100 kbit/s. The
whole message transmission is executed by the driver. The driver
triggers all steps over control, status and data register. There are no
FIFOs or interrupts.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
On chipsets with a second 'Integrated Device Function' SMBus controller use
a different adapter-name for the second IDF adapter.
This allows platform glue code which is looking for the primary i801
adapter to manually instantiate i2c_clients on to differentiate
between the 2.
This allows such code to find the primary i801 adapter by name, without
needing to duplicate the PCI-ids to feature-flags mapping from i2c-i801.c.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
On Intel Denverton SoC ismt controller may enter weird state when
transaction gets stuck. It times out in the driver, but unless
transaction is explicitly killed in the controller, it won't be able to
perform new transactions anymore.
The issue is extremely difficult to reproduce and may take weeks of non-
stop smbus traffic.
Numerous hours with logic analyzer didn't yield any useful results, it
looks like the controller stops toggling SCK line, i.e. the issue is
likely in the controller, since device doesn't do clock stretching, so
nothing is driving SCK except the host.
Explicitly kill transaction on timeout to recover the controller from
this state.
Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There are quite a few drivers and options for the DesignWare
I2C adapter in the Kconfig. Grouping all of them under the
I2C_DESIGNWARE_CORE. That makes the menuconfig a bit more
easier to understand.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
'struct i2c_algorithm' and 'struct virtio_device_id' are not modified in
this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers, which is the case for struct i2c_algorithm.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
6663 568 16 7247 1c4f drivers/i2c/busses/i2c-virtio.o
After:
=====
text data bss dec hex filename
6735 472 16 7223 1c37 drivers/i2c/busses/i2c-virtio.o
--
Compile tested only
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
rcar_i2c_probe() has priv->devtype operation, but handling (A) and (C)
in same place is more understandable ( (A) and (B) are independent).
(A) if (priv->devtype < I2C_RCAR_GEN3) {
...
}
(B) ...
(C) if (priv->devtype >= I2C_RCAR_GEN3) {
...
}
Let's merge it with if-else
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To ensure code clarity and prevent potential errors, it's advisable
to employ the ';' as a statement separator, except when ',' are
intentionally used for specific purposes.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
While at it, no more special handling needed here, remove the goto
label "err:".
Signed-off-by: Rong Qianfeng <rongqianfeng@vivo.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
While at it, no need to save clk pointer, drop sclk from struct
em_i2c_device.
Signed-off-by: Rong Qianfeng <rongqianfeng@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The smatch check warning is "buffer overflow 'npcm_i2caddr' 2 <= 9".
The original design supports 10 target addresses although only 2
addresses are required for current implementation.
Restore the npcm_i2caddr array length to fix the smatch warning.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202408130818.FgDP5uNm-lkp@intel.com/
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
devm_clk_get_optional() and clk_prepare_enable() can be replaced by the
helper function devm_clk_get_optional_enabled(). Let's simplify the code by
using devm_clk_get_optional_enabled() and avoid calling
clk_disable_unprepare().
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We have the same (*) PM ops in the PCI and platform drivers.
Instead, consolidate that PM ops under exported variable and
deduplicate them.
*)
With the subtle ACPI and P-Unit behaviour differences in PCI case.
But this is not a problem as for ACPI we need to take care of the
P-Unit semaphore anyway and calling PM ops for PCI makes sense as
it might provide specific operation regions in ACPI (however there
are no known devices on market that are using it with PCI enabled I2C).
Note, the clocks are not in use in the PCI case.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sanket Goswami <Sanket.Goswami@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Simplify checking for unsupported bus speeds and reporting errors by
factoring out the calculation of the maximum bus speed, and by using the
dev_err_probe() helper.
While at it, use "%u" for u32, and improve the error message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Commit 90312351fd ("i2c: designware: MASTER mode as separated driver")
introduced ->disable() callback but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable() and scope is inside the same kernel module.
That said, replace the callback by explicitly calling the i2c_dw_disable().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reduce scope of the I²C DesignWare driver exports to I2C_DW namespaces.
This will prevent abuse of the symbols and clean up global namespace.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Instead of asymmetrical checks for the firmware type use
the is_*_node() calls.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We have the same code flows in the PCI and platform drivers. Moreover,
the flow requires the common code to export a few functions. Instead,
consolidate that flow under new function called
i2c_dw_fw_parse_and_configure() and drop unneeded exports.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
For the sake of consistency, rename dw_i2c_of_configure() and change
its parameter to be aligned with the i2c_dw_acpi_configure().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Fast mode plus is available on most of the IP variants that RIIC driver
is working with. The exception is (according to HW manuals of the SoCs
where this IP is available) the Renesas RZ/A1H. For this, patch
introduces the struct riic_of_data::fast_mode_plus.
Fast mode plus was tested on RZ/G3S, RZ/G2{L,UL,LC}, RZ/Five by
instantiating the RIIC frequency to 1MHz and issuing i2c reads on the
fast mode plus capable devices (and the i2c clock frequency was checked on
RZ/G3S).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Define individual arrays to describe the register offsets. In this way
we can describe different IP variants that share the same register offsets
but have differences in other characteristics. Commit prepares for the
addition of fast mode plus.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add suspend/resume support for the RIIC driver. This is necessary for the
Renesas RZ/G3S SoC which support suspend to deep sleep state where power
to most of the SoC components is turned off. As a result the I2C controller
needs to be reconfigured after suspend/resume. For this, the reset line
was stored in the driver private data structure as well as i2c timings.
The reset line and I2C timings are necessary to re-initialize the
controller after resume.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Enable runtime PM autosuspend support for the RIIC driver. With this, in
case there are consecutive xfer requests the device wouldn't be runtime
enabled/disabled after each consecutive xfer but after the
the delay configured by user. With this, we can avoid touching hardware
registers involved in runtime PM suspend/resume saving in this way some
cycles. The default chosen autosuspend delay is zero to keep the
previous driver behavior.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
pm_runtime_get_sync() may return with error. In case it returns with error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is no need to runtime resume the device as long as the IP registers
are not accessed. Calling pm_runtime_get_sync() at the register access
time leads to a simpler error path.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use a temporary variable for the struct device pointers to avoid
dereferencing.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
dw_i2c_of_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
i2c_dw_acpi_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is no need to have ugly ifdeffery and additional macros
for the device ID tables. Always provide them. Since we touch
the ACPI table, make it sorted by ID.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Make the terminator entry look the same in all device ID tables.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
PCI core, after pcim_enable_device(), takes care about the allocated
IRQ vectors, no need to do it explicitly and break the cleaning up
order.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace a while-loop by for-loop in i2c_dw_probe_lock_support() to
save a few lines of code.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace SET_RUNTIME_PM_OPS() with its modern RUNTIME_PM_OPS()
alternative.
The combined usage of pm_ptr() and RUNTIME_PM_OPS() allows the
compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In the mtk_i2c_irq() handler, variable restart_flag is initialized
to zero and then reassigned with I2C_RS_TRANSFER if and only if
auto_restart is enabled.
Avoid a double initialization of this variable by transferring the
auto_restart check to the restart_flag declaration.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Delimiters are meant to be last, no need for a ',' there. Remove a
superfluous newline in the ali1535 driver while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When disabling CONFIG_X86_AMD_PLATFORM_DEVICE option, the driver
'drivers/acpi/acpi_apd.c' won't be compiled. This leads to a situation
where BMC (Baseboard Management Controller) cannot retrieve the memory
temperature via the i2c interface after i2c DW driver is loaded. Note
that BMC can retrieve the memory temperature before booting into OS.
[Debugging Detail]
1. dev->pclk and dev->clk are NULL when calling devm_clk_get_optional()
in dw_i2c_plat_probe().
2. The callings of i2c_dw_scl_hcnt() in i2c_dw_set_timings_master()
return 65528 (-8 in integer format) or 65533 (-3 in integer format).
The following log shows SS's HCNT/LCNT:
i2c_designware AMDI0010:01: Standard Mode HCNT:LCNT = 65533:65535
3. The callings of i2c_dw_scl_lcnt() in i2c_dw_set_timings_master()
return 65535 (-1 in integer format). The following log shows SS's
HCNT/LCNT:
i2c_designware AMDI0010:01: Fast Mode HCNT:LCNT = 65533:65535
4. i2c_dw_init_master() configures the register IC_SS_SCL_HCNT with
the value 65533. However, the DW i2c databook mentioned the value
cannot be higher than 65525. Quote from the DW i2c databook:
NOTE: This register must not be programmed to a value higher than
65525, because DW_apb_i2c uses a 16-bit counter to flag an
I2C bus idle condition when this counter reaches a value of
IC_SS_SCL_HCNT + 10.
5. Since ss_hcnt, ss_lcnt, fs_hcnt, and fs_lcnt are the invalid
values, we should not write the corresponding registers.
Fix the issue by reading dev->{ss,fs,hs}_hcnt and dev->{ss,fs,hs}_lcnt
from HW registers if ic_clk is not set.
Reported-by: Dong Wang <wangdong28@lenovo.com>
Suggested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Dong Wang <wangdong28@lenovo.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/linux-i2c/8295cbe1-a7c5-4a35-a189-5d0bff51ede6@linux.intel.com/
On ACPI machines, the tegra i2c module encounters an issue due to a
mutex being called inside a spinlock. This leads to the following bug:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
...
Call trace:
__might_sleep
__mutex_lock_common
mutex_lock_nested
acpi_subsys_runtime_resume
rpm_resume
tegra_i2c_xfer
The problem arises because during __pm_runtime_resume(), the spinlock
&dev->power.lock is acquired before rpm_resume() is called. Later,
rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on
mutexes, triggering the error.
To address this issue, devices on ACPI are now marked as not IRQ-safe,
considering the dependency of acpi_subsys_runtime_resume() on mutexes.
Fixes: bd2fdedbf2 ("i2c: tegra: Add the ACPI support")
Cc: <stable@vger.kernel.org> # v5.17+
Co-developed-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add the missing geni_icc_disable() call before returning in the
geni_i2c_runtime_resume() function.
Commit 9ba48db9f7 ("i2c: qcom-geni: Add missing
geni_icc_disable in geni_i2c_runtime_resume") by Gaosheng missed
disabling the interconnect in one case.
Fixes: bf225ed357 ("i2c: i2c-qcom-geni: Add interconnect support")
Cc: Gaosheng Cui <cuigaosheng1@huawei.com>
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add the missing clk_disable_unprepare() before return in
geni_i2c_runtime_resume().
Fixes: 14d02fbadb ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The piix4 I2C bus can carry SPDs, register them if present.
Only look on bus 0, as this is where the SPDs seem to be located.
Only the first 8 slots are supported. If the system has more,
then these will not be visible.
The AUX bus can not be probed as on some platforms it reports all
devices present and all reads return "0".
This would allow the ee1004 to be probed incorrectly.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
regarding unneeded 'driver_data' and more sanity checks in the char
device.
For the host drivers, this release includes significant updates, with
the primary change being the renaming from "master/slave" to
"controller/target" to adhere to I2C v7 and SMBus 3.2 standards.
New Support:
- Added support for Intel Arrow Lake-H.
- Added I2C support in the Arioha SoC by linking the Mediatek
I2C controller.
Cleanups:
- Added the MODULE_DESCRIPTION() macro, resolving a modpost
warning in the ALi 1563 Southbridge driver.
- Constified the regmap_config declaration in the i2c-designware
driver.
- Improved the coding style in the Renesas R-Car driver by
removing unnecessary semicolons after brackets.
General improvements:
- In the OMAP device, replaced NOIRQ_SYSTEM_SLEEP_PM_OPS with
RUNTIME_PM_OPS to enable waking up the controller during
suspend() before suspend_noirq() kicks in.
- Improved logging in the Xilinx driver.
- Added a warning (WARN()) in the Renesas R-Car driver for
spurious interrupts.
DTS Changes:
- Removed address-cell and size-cell from the Atmel at91sam,
nVidia Tegra 20, and Samsung S3c2410 devices.
- Fixed Texas Instruments OMAP4 I2C controller to comply with
the i2c-controller.yaml schema.
- Improved indentation in DTS examples for several I2C devices.
- Converted the NXP LPC1788 binding to the dt-schema.
- Added documentation for the compatible string
thead,th1520-i2c.
- Added the "power-domains" property for the Meson I2C driver.
AT24 EEPROM driver changes:
- add support for two new Microchip models
- document even more new models in DT bindings (those use fallback
compatibles so no code changes)
-----BEGIN PGP SIGNATURE-----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=perV
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.11-rc1-try2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The I2C core gains documentation updates for the testunit, a cleanup
regarding unneeded 'driver_data' and more sanity checks in the char
device.
For the host drivers, this release includes significant updates, with
the primary change being the renaming from "master/slave" to
"controller/target" to adhere to I2C v7 and SMBus 3.2 standards.
New Support:
- Added support for Intel Arrow Lake-H
- Added I2C support in the Arioha SoC by linking the Mediatek I2C
controller
Cleanups:
- Added the MODULE_DESCRIPTION() macro, resolving a modpost warning
in the ALi 1563 Southbridge driver.
- Constified the regmap_config declaration in the i2c-designware
driver.
- Improved the coding style in the Renesas R-Car driver by removing
unnecessary semicolons after brackets.
General improvements:
- In the OMAP device, replaced NOIRQ_SYSTEM_SLEEP_PM_OPS with
RUNTIME_PM_OPS to enable waking up the controller during suspend()
before suspend_noirq() kicks in.
- Improved logging in the Xilinx driver.
- Added a warning (WARN()) in the Renesas R-Car driver for spurious
interrupts.
DTS Changes:
- Removed address-cell and size-cell from the Atmel at91sam, nVidia
Tegra 20, and Samsung S3c2410 devices.
- Fixed Texas Instruments OMAP4 I2C controller to comply with the
i2c-controller.yaml schema.
- Improved indentation in DTS examples for several I2C devices.
- Converted the NXP LPC1788 binding to the dt-schema.
- Added documentation for the compatible string thead,th1520-i2c.
- Added the "power-domains" property for the Meson I2C driver.
AT24 EEPROM driver changes:
- add support for two new Microchip models
- document even more new models in DT bindings (those use fallback
compatibles so no code changes)"
* tag 'i2c-for-6.11-rc1-try2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (87 commits)
i2c: document new callbacks in i2c_algorithm
dt-bindings: i2c: amlogic,meson6-i2c: add optional power-domains
dt-bindings: i2c: at91: Add sama7d65 compatible string
i2c: st: reword according to newest specification
i2c: cpm: reword according to newest specification
i2c: virtio: reword according to newest specification
i2c: nvidia-gpu: reword according to newest specification
i2c: viai2c: reword according to newest specification
i2c: viperboard: reword according to newest specification
i2c: uniphier: reword according to newest specification
i2c: uniphier-f: reword according to newest specification
i2c: tiny-usb: reword according to newest specification
i2c: thunderx-pcidrv: reword according to newest specification
i2c: tegra-bpmp: reword according to newest specification
i2c: taos-evm: reword according to newest specification
i2c: sun6i-p2wi: reword according to newest specification
i2c: stm32f4: reword according to newest specification
i2c: sprd: reword according to newest specification
i2c: sis5595: reword according to newest specification
i2c: rzv2m: reword according to newest specification
...
Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit systems,
have been in linux-next for a while with no reported issues. The
Kconfig fixup went in 29 hours ago, so might have missed the latest
linux-next, but was acked by everyone involved.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppR4w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwoQCeIaW3nbOiNTmOupvEnZwrN3yVNs8An3Q5L+Br
1LpTASaU6A8pN81Z1m5g
=6U1z
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc and other driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit
systems, have been in linux-next for a while with no reported issues.
The Kconfig fixup went in 29 hours ago, so might have missed the
latest linux-next, but was acked by everyone involved"
* tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
misc: Kconfig: exclude mrvl-cn10k-dpi compilation for 32-bit systems
misc: delete Makefile.rej
binder: fix hang of unregistered readers
misc: Kconfig: add a new dependency for MARVELL_CN10K_DPI
virtio: add missing MODULE_DESCRIPTION() macro
agp: uninorth: add missing MODULE_DESCRIPTION() macro
spmi: add missing MODULE_DESCRIPTION() macros
dev/parport: fix the array out-of-bounds risk
samples: configfs: add missing MODULE_DESCRIPTION() macro
misc: mrvl-cn10k-dpi: add Octeon CN10K DPI administrative driver
misc: keba: Fix missing AUXILIARY_BUS dependency
slimbus: Fix struct and documentation alignment in stream.c
MAINTAINERS: CC dri-devel list on Qualcomm FastRPC patches
misc: fastrpc: use coherent pool for untranslated Compute Banks
misc: fastrpc: support complete DMA pool access to the DSP
misc: fastrpc: add missing MODULE_DESCRIPTION() macro
misc: fastrpc: Add missing dev_err newlines
misc: fastrpc: Use memdup_user()
nvmem: core: Implement force_ro sysfs attribute
nvmem: Use sysfs_emit() for type attribute
...
R-Car Gen3+ needs a reset before every controller transfer. That erases
configuration of a potentially in parallel running local target
instance. To avoid this disruption, avoid controller transfers if a
local target is running. Also, disable SMBusHostNotify because it
requires being a controller and local target at the same time.
Fixes: 3b770017b0 ("i2c: rcar: handle RXDMA HW behaviour on Gen3")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a superfluous debug output which is already available via
tracing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a superfluous debug output which is already available via
tracing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove and reword comments while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Remove a useless comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We should allow RXDMA only if the reset was really successful, so clear
the flag after the reset call.
Fixes: 0e864b552b ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
A newline was missing and closing braces of functions do not need a
semicolon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The FIXME is very old and probably needed because of some driver bug
like insufficient initialization. It may well be that it was fixed
meanwhile but we never know because the spurious irq is silently
ignored. Add now a call trace when this happens so we have more
information in case the issue still exists.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When probing, the hardware is not brought into a known state. This may
be a problem when a hypervisor restarts Linux without resetting the
hardware, leaving an old state running. Make sure the hardware gets
initialized, especially interrupts should be cleared and disabled.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/r/20240702045535.2000393-1-dirk.behme@de.bosch.com
Fixes: 6ccbe60713 ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce i2c support to Airoha EN7581 SoC through the i2c-mt7621
driver.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Ray Liu <ray.liu@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
`bt1_i2c_cfg` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
A device may need the controller up during suspend_noirq() or
resume_noirq().
But if the controller is autosuspended, there is no way to wakeup it during
suspend_noirq() or resume_noirq() because runtime pm is disabled at this
time.
The suspend() callback wakes up the controller, so it is available until
its suspend_noirq() callback (pm_runtime_force_suspend()).
During the resume, it's restored by resume_noirq() callback
(pm_runtime_force_resume()). Then resume() callback enables autosuspend.
So the controller is up during a little time slot in suspend and resume
sequences even if it's not used.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() by
NOIRQ_SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS().
The usage of pm_ptr() and these more recent macros allows the compiler to
see and drop the dead code.
The unnecessary '__maybe_unused' annotations on PM functions can be
removed.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-ccgx-ucsi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-ali1563.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-pxa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/i2c/busses/i2c-qup.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When del_timer_sync() is called in an interrupt context it throws a warning
because of potential deadlock. The timer is used only to exit from
wait_for_completion() after a timeout so replacing the call with
wait_for_completion_timeout() allows to remove the problematic timer and
its related functions altogether.
Fixes: 41561f28e7 ("i2c: New Philips PNX bus driver")
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
'devmodel' hasn't actually been used since:
'commit 3275158fa5 ("parport: remove use of devmodel")'
and everyone now has it set to true and has been fixed up; remove
the flag.
(There are still comments all over about it)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240502154823.67235-4-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c-viai2c-common.c file is used by two drivers, but is not a proper
abstraction and can get linked into both modules in the same configuration,
which results in a warning:
scripts/Makefile.build:236: drivers/i2c/busses/Makefile: i2c-viai2c-common.o is added to multiple modules: i2c-wmt i2c-zhaoxin
The other problems with this include the incorrect use of a __weak function
when both are built-in, and the fact that the "common" module is sprinked
with 'if (i2c->plat == ...)' checks that have knowledge about the differences
between the drivers using it.
Avoid the link time warning by making the common driver a proper module
with MODULE_LICENCE()/MODULE_AUTHOR() tags, and remove the __weak function
by slightly rearranging the code.
This adds a little more duplication between the two main drivers, but
those versions get more readable in the process.
Fixes: a06b80e830 ("i2c: add zhaoxin i2c controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Hans Hu <HansHu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Setting IACK bit when core is disabled does not clear the "Interrupt Flag"
bit in the status register, and the interrupt remains pending.
Sometimes it causes failure for the very first message transfer, that is
usually a device probe.
Hence, set IACK bit after core is enabled to clear pending interrupt.
Fixes: 18f98b1e31 ("[PATCH] i2c: New bus driver for the OpenCores I2C controller")
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 5b6d721b26 ("i2c: designware: enable SLAVE in platform module")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Luis Oliveira <lolivei@synopsys.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
'pclk' is only used locally in the probe. Remove it from the
'synquacer_i2c' structure.
Also remove a useless debug message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
further deprecate class based I2C device instantiation. All users are
converted, too. Other that that, Andi collected a number if I2C host
driver patches. Those merges have their own description.
-----BEGIN PGP SIGNATURE-----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=viLd
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core removes an argument from the i2c_mux_add_adapter() call to
further deprecate class based I2C device instantiation. All users are
converted, too.
Other that that, Andi collected a number if I2C host driver patches.
Those merges have their own description"
* tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (72 commits)
power: supply: sbs-manager: Remove class argument from i2c_mux_add_adapter()
i2c: mux: Remove class argument from i2c_mux_add_adapter()
i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()
i2c: acpi: Unbind mux adapters before delete
i2c: designware: Replace MODULE_ALIAS() with MODULE_DEVICE_TABLE()
i2c: pxa: use 'time_left' variable with wait_event_timeout()
i2c: s3c2410: use 'time_left' variable with wait_event_timeout()
i2c: rk3x: use 'time_left' variable with wait_event_timeout()
i2c: qcom-geni: use 'time_left' variable with wait_for_completion_timeout()
i2c: jz4780: use 'time_left' variable with wait_for_completion_timeout()
i2c: synquacer: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f7: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f4: use 'time_left' variable with wait_for_completion_timeout()
i2c: st: use 'time_left' variable with wait_for_completion_timeout()
i2c: omap: use 'time_left' variable with wait_for_completion_timeout()
i2c: imx-lpi2c: use 'time_left' variable with wait_for_completion_timeout()
i2c: hix5hd2: use 'time_left' variable with wait_for_completion_timeout()
i2c: exynos5: use 'time_left' variable with wait_for_completion_timeout()
i2c: digicolor: use 'time_left' variable with wait_for_completion_timeout()
i2c: amd-mp2-plat: use 'time_left' variable with wait_for_completion_timeout()
...
- Updates to AMBA bus subsystem to drop .owner struct device_driver
initialisations, moving that to code instead.
- Add LPAE privileged-access-never support
- Add support for Clang CFI
- clkdev: report over-sized device or connection strings
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuNNh8scc2k/wOAE+9OeQG+StrGQFAmZF8aoACgkQ9OeQG+St
rGShNg//aShGJvs0ezHMt7j4MVrToGHgmpkryaMiYDPU6ud3xSM29sIMxtdEw6yR
DGJp8Lcx2KsJU8HKwEzRl7dMr4Cx16bXj69lHNCmalOflTOPCDJuZZ87OUFD6fXh
RNbDbEnPlp474E1f3rJB4WkB3UA+hUq/26Z8mpfbWLunVMUeCilgKiDFQzJMobMH
smHx1TyBwTDPbY6jHqdiGEzSoLzvDdtSFyYz69aRy8rfUHXESVdvqkXWMf33Bf60
fONhK4O4ln8iaQT0MmbWbV4TGNeOzqeNC4M4U3bVAyrwW4naSRFnVQEVJdaAgM/P
6w5DLpStjef5YHpGbx3nodBb+xvi0Kb25vL/fvnsmVLqPV3Rsp8T3d1WQI8RWnJo
GphHk2QmogdOFwoiyMLXv6JZrc796SogSQBlF5lj3LoR8RCjuYUMVOvikTqfF0BK
gMbvtF4v3SwJoKitjbiRgkusPEmziooi7hTwluFuWNfmkc7dJKPkfMhC0RkvIn0J
VpL17A3A35YBnpjTAxTMsAh4OsBRasvBK/4np8nizwre+K5pPuF0PV6rFhndD31h
JKfkXgIziyVN5TVfoocM1kQqQmDjTkyOmehgZ0dYRORyGJMoDgy6LUucQRziLubm
C5Od5hcPhHhN8lECBjMA9P+9m0S+PvK3vepefdNIpSMoQwxAMFQ=
=t/xl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux
Pull ARM updates from Russell King:
- Updates to AMBA bus subsystem to drop .owner struct device_driver
initialisations, moving that to code instead.
- Add LPAE privileged-access-never support
- Add support for Clang CFI
- clkdev: report over-sized device or connection strings
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux: (36 commits)
ARM: 9398/1: Fix userspace enter on LPAE with CC_OPTIMIZE_FOR_SIZE=y
clkdev: report over-sized strings when creating clkdev entries
ARM: 9393/1: mm: Use conditionals for CFI branches
ARM: 9392/2: Support CLANG CFI
ARM: 9391/2: hw_breakpoint: Handle CFI breakpoints
ARM: 9390/2: lib: Annotate loop delay instructions for CFI
ARM: 9389/2: mm: Define prototypes for all per-processor calls
ARM: 9388/2: mm: Type-annotate all per-processor assembly routines
ARM: 9387/2: mm: Rewrite cacheflush vtables in CFI safe C
ARM: 9386/2: mm: Use symbol alias for cache functions
ARM: 9385/2: mm: Type-annotate all cache assembly routines
ARM: 9384/2: mm: Make tlbflush routines CFI safe
ARM: 9382/1: ftrace: Define ftrace_stub_graph
ARM: 9358/2: Implement PAN for LPAE by TTBR0 page table walks disablement
ARM: 9357/2: Reduce the number of #ifdef CONFIG_CPU_SW_DOMAIN_PAN
ARM: 9356/2: Move asm statements accessing TTBCR into C functions
ARM: 9355/2: Add TTBCR_* definitions to pgtable-3level-hwdef.h
ARM: 9379/1: coresight: tpda: drop owner assignment
ARM: 9378/1: coresight: etm4x: drop owner assignment
ARM: 9377/1: hwrng: nomadik: drop owner assignment
...
A substantial code cleanup from Wolfram affects many drivers:
- Removed dev_err() in case of timeout during i2c transfers, as
timeouts are not considered errors and should not be treated
as such.
- For the same reason, 'timeout' variables have been renamed to
'time_left'.
Other cleanups:
- The viperboard driver now omits the "owner = THIS_MODULE"
assignment.
- Finally, we have eliminated the last remnants of
I2C_CLASS_SPD: support for class-based devices has been
completely removed from the mux-gpio driver.
- In the ocore devices, a more standard use of ioport_map() for
8-bit I/O read/write operations has been implemented.
- The mpc driver will be among the first i2c drivers and one of
the first in the kernel to use the __free auto cleanup
routine.
- The designware driver now uses MODULE_DEVICE_TABLE() instead
of MODULE_ALIAS() for better consistency with the ID table.
- Added prefixes to the octeon register macros.
- Fixed some checkpatch errors in the newly created
i2c-viai2c-common.c file.
Code refactoring:
- The riic driver has refactored read/write operations to more
flexibly support new platforms, laying the foundation for new
SoC peculiarities.
- In the i801 driver, a notifier callback has been created for
muxed child segments.
- The lpi2c driver now sets a clock rate during probe instead
of continuously calling clk_get_rate().
- Improvements in the clock divisor logic to accommodate other
clock frequencies.
- Combined some common functionalities during initialization
for the wmt driver and separated others that can be
independently used by different drivers. Now, all the common
functionalities are grouped in the i2c-viai2c-common.c file.
- Improved the clock stretching mechanism in the newly created
i2c-viai2c-common.c file, inherited from the previous
i2c-wmt.c.
Features added:
- The octeon driver now includes watchdog timeout handling.
- Added high-speed support for the octeon driver.
Added support for:
- R9A09G057 SoC in the riic driver.
- Rapids-D I2C controller in the designware driver.
- Cadence driver now also supports RISC-V architectures.
- Added support to the WMT device as a separate driver using the
newly created i2c-viai2c-common.c functionalities.
- Added support for the Zhaoxin I2C controller.
Some improvements in the bindings:
- The pnx driver is converted to dtschema.
- Added documentation for the Qualcomm SC8280XP.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZj/GzxYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1uJQgA/3DBT5R6OYbIg1Ky4u9A9hwwmqqN
EnNcygEovf1BpMiSAQC7Nrmv/CKUkmk0YNV9Ho94XYjFxIHqgKwUwySsocrFAQ==
=MW8c
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
Code cleanup:
A substantial code cleanup from Wolfram affects many drivers:
- Removed dev_err() in case of timeout during i2c transfers, as
timeouts are not considered errors and should not be treated
as such.
- For the same reason, 'timeout' variables have been renamed to
'time_left'.
Other cleanups:
- The viperboard driver now omits the "owner = THIS_MODULE"
assignment.
- Finally, we have eliminated the last remnants of
I2C_CLASS_SPD: support for class-based devices has been
completely removed from the mux-gpio driver.
- In the ocore devices, a more standard use of ioport_map() for
8-bit I/O read/write operations has been implemented.
- The mpc driver will be among the first i2c drivers and one of
the first in the kernel to use the __free auto cleanup
routine.
- The designware driver now uses MODULE_DEVICE_TABLE() instead
of MODULE_ALIAS() for better consistency with the ID table.
- Added prefixes to the octeon register macros.
- Fixed some checkpatch errors in the newly created
i2c-viai2c-common.c file.
Code refactoring:
- The riic driver has refactored read/write operations to more
flexibly support new platforms, laying the foundation for new
SoC peculiarities.
- In the i801 driver, a notifier callback has been created for
muxed child segments.
- The lpi2c driver now sets a clock rate during probe instead
of continuously calling clk_get_rate().
- Improvements in the clock divisor logic to accommodate other
clock frequencies.
- Combined some common functionalities during initialization
for the wmt driver and separated others that can be
independently used by different drivers. Now, all the common
functionalities are grouped in the i2c-viai2c-common.c file.
- Improved the clock stretching mechanism in the newly created
i2c-viai2c-common.c file, inherited from the previous
i2c-wmt.c.
Features added:
- The octeon driver now includes watchdog timeout handling.
- Added high-speed support for the octeon driver.
Added support for:
- R9A09G057 SoC in the riic driver.
- Rapids-D I2C controller in the designware driver.
- Cadence driver now also supports RISC-V architectures.
- Added support to the WMT device as a separate driver using the
newly created i2c-viai2c-common.c functionalities.
- Added support for the Zhaoxin I2C controller.
Some improvements in the bindings:
- The pnx driver is converted to dtschema.
- Added documentation for the Qualcomm SC8280XP.
If an error occurs after the clk_prepare_enable() call, it should be undone
by a corresponding clk_disable_unprepare() call, as already done in the
remove() function.
As devm_clk_get() is used, we can switch to devm_clk_get_enabled() to
handle it automatically and fix the probe.
Update the remove() function accordingly and remove the now useless
clk_disable_unprepare() call.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
As Krzysztof Kozlowski pointed out the better is to use
MODULE_DEVICE_TABLE() as it will be consistent with the content
of the real ID table of the platform devices.
While at it, drop unneeded and unused module alias in PCI glue
driver as PCI already has its own ID table and automatic loading
should just work.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231120144641.1660574-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout and turn
the SMBus-specific termination message to debug.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add Zhaoxin I2C controller driver. It provides the access to the i2c
busses, which connects to the touchpad, eeprom, I2S, etc.
Zhaoxin I2C controller has two separate busses, so may accommodate up
to two I2C adapters. Those adapters are listed in the ACPI namespace
with the IIC1D17 HID, and probed by a platform driver.
The driver works with IRQ mode, and supports basic I2C features. Flags
I2C_AQ_NO_ZERO_LEN and I2C_AQ_COMB_WRITE_THEN_READ are used to limit
the unsupported access.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Enumeration variables are added to differentiate
between different platforms.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
During each byte access, the host performs clock stretching.
To reduce the host performs clock stretching, move most of
the per-msg processing to the interrupt context.
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
1. The I2C IP for both wmt and zhaoxin originates from VIA. Rename
common registers, functions, and variable names to follow the
VIAI2C_ and viai2c_ naming conventions for consistency and clarity.
2. rename i2c_dev to i2c, to shorten the length of a line.
3. rename wait_result to time_left, make it better to reflect the meaning
of the value returned by wait_for_completion_timeout().
4. remove TCR_MASTER_WRITE, its value is 0.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Since the I2C IP of both wmt and zhaoxin originates from VIA,
it is better to separate the common code first.
The common driver is named as i2c-viai2c-common.c.
Old i2c-wmt.c renamed to i2c-viai2c-wmt.c.
The MAINTAINERS file will be updated accordingly in upcoming commits.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some common initialization actions are put in the function
wmt_i2c_init(), which is convenient to share with zhaoxin.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Read the ioclk property as reference clock if sclk not present in acpi
table to make it SOC agnostic.
In case, it's not populated from dts/acpi table, use the default clock
of 800 MHz which is optimal in either case of sclk/ioclk.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add watchdog timeout handling to cater to the unhandled warnings
seen during validation on boards with different I2C slaves.
This status code reflects the state that controller couldn't
receive any response from slave while being in non-idle state
and HW recommends to reset before any further bus access.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The macros for TWSI register's offset are generically
named, rename them to be platform specific macros by
adding 'OCTEON_REG' as prefix.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To support bus operations for high speed bus frequencies greater than
400KHZ following control bits need to be setup accordingly
- hs_mode (bit 0) field in Mode register to switch controller
between low-speed and high-speed frequency operating mode.
- Setup clock divisors for desired TWSI bus frequency using
FOSCL output frequency divisor (D):
0 - sets the divisor to 10 for low speed mode
1 - sets the divisor to 15 for high speed mode.
The TWSI bus output frequency, in master mode is based on:
TCLK = 100MHz / (THP + 2)
FOSCL = FSAMP / (M+1)×D = TCLK / (2 ^ N × (M + 1) × 15)
FSAMP = TCLK / 2 ^ N
where,
N is <2:0> and M is <6:3> of TWSI Clock Control Register
D is 10 for low speed or 15 for HS_MODE
With high speed mode support, HLC mode usage is limited to
low speed frequency (<=400KHz) bus transfers in hardware.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Handle changes to clock divisor logic for OcteonTX2 SoC family using
subsystem ID and using default reference clock source as 100MHz.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add RISCV support to Cadence I2C Kconfig which is used in platform
such as the StarFive JH8100.
Signed-off-by: Eng Lee Teh <englee.teh@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
