"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87v8l3z3y8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87tu0nz3xr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PLLs are modeled as fixed factor clocks, based on initial
settings. However, enabling CPU boost clock rates requires increasing
the PLL clock rates.
Add a custom clock driver to model the PLL clocks on R-Car Gen4, and use
it for PLL2 on R-Car V4H. This allows the Z clock (Cortex-A76 core
clock) to request PLL rate changes, and enable boost mode for the High
Performance mode. For now this is limited to integer multiplication
modes.
Note that the definition for CPG_PLLxCR0_NI uses the value for R-Car V4H.
On R-Car S4-8, the integer and fractional multiplication fields are one
bit larger resp. smaller, but R-Car S4-8 does not support High
Performance mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/76a5952900a6e15604c640bc8a27762e0e936677.1670492384.git.geert+renesas@glider.be
The CFG_USB[H2MODE] allows to switch the USB configuration. The
configuration supported are:
- One host and one device
or
- Two hosts
Set CFG_USB[H2MODE] based on the USBF controller (USB device)
availability.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-3-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If cpg_mssr_common_init() fails after assigning priv to global variable
cpg_mssr_priv, it deallocates priv, but cpg_mssr_priv keeps dangling
pointer that potentially can be used later.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f7db7bbf0 ("clk: renesas: cpg-mssr: Add early clock support")
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1671806417-32623-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CRU clock and reset entries to CPG driver.
CRU_SYSCLK and CRU_VCLK clocks need to be turned ON/OFF in particular
sequence for the CRU block hence add these clocks to
r9a07g044_no_pm_mod_clks[] array and pass it as part of CPG data for
both RZ/G2L and RZ/V2L SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221221212703.348278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add Compare-Match Timer (TIM) clock and reset entries to CPG
driver.
The TIM IP on the RZ/V2M comes with 32 channels, but the ISP has
full control of channels 0 to 7, and channels 24 to 31. Therefore
Linux is only allowed to use channels 8 to 23.
The TIM has shared peripheral clock with other modules, so mark it
as critical clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221205145955.391526-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks related to display which are needed to get the DSI output
working.
Extracted from Renesas BSP tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221201095631.89448-4-tomi.valkeinen+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the table in Note 5 for the OSC clock in Table 8.1.4e
("Lists of CPG clocks generated from PLL5") of the R-Car V4H Series
Hardware User's Manual Rev. 0.54, the predividers for the OSC clock are
16 resp. 32 when using a 16.66 resp. 33.33 MHz external crystal.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/dcd572acc584c237f70d2309e038f25040236a87.1669740722.git.geert+renesas@glider.be
Add PWM{8..14} clock and reset entries to CPG driver.
The PWM IP on the RZ/V2M comes with 16 channels, but the ISP has
full control of channels 0 to 7, and channel 15, therefore Linux
is only allowed to use channels 8 to 14.
The PWM channel 15 shares apb clock and reset with PWM{8..14}.
The reset is deasserted by the bootloader/ISP.
Add PWM{8..14} clocks to CPG driver and mark apb clock as
critical clock, so that the apb clock will be always on.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221124191643.3193423-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RSwitch2 and EtherTSN-IF clocks were accidentally mixed up.
While at it, rename them to better match the (future) documentation.
Fixes: a3b4137a4d ("clk: renesas: r8a779f0: Add Ethernet Switch clocks")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/99b8b41bd2c5043c9e457862ef4bc144869eca58.1668501212.git.geert+renesas@glider.be
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the SCIF modules from the S0D12_PER
clock to the SASYNCPERD4 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 080bcd8d59 ("clk: renesas: r8a779f0: Add HSCIF clocks")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If condition (clkspec.np != pd->dev.of_node) is true, then the driver
ends up in an endless loop, forever, locking up the machine.
Fixes: aad03a66f9 ("clk: renesas: r9a06g032: Add clock domain support")
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20221028113834.7496-1-marex@denx.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are cases where not all CPG_MOD clocks should be assumed to support
PM. For example on the CRU block there is a particular sequence that needs
to be followed to initialize the CSI-2 D-PHY in which individual clocks
need to be turned ON/OFF, due to which Runtime PM support wasn't used by
the CRU CSI-2 driver.
This patch adds support to allow indicating if PM is not supported by the
CPG_MOD clocks. Two new members no_pm_mod_clks and num_no_pm_mod_clks are
added to struct rzg2l_cpg_info so that MOD clocks which do not support PM
can be passed by no_pm_mod_clks[] array and when the driver uses Runtime
PM support the clk ID is matched against the no_pm_mod_clks[] array to see
if the clk is needed to be included as part of Runtime PM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026014227.162121-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix typo pll5_mux_dsi_div_params -> mux_dsi_div_params
Fixes the below warning (make W=1):
drivers/clk/renesas/rzg2l-cpg.c:115: warning: Function parameter or member 'mux_dsi_div_params' not described in 'rzg2l_cpg_priv'
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026012123.159790-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the SPI Multi I/O Bus Controller (RPC-IF)
on the Renesas R-Car V4H (R8A779G0) SoC.
While at it, fix table alignment in the definition of the related
RPCSRC internal clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f0609c82e742865be753b67a0a6080f193f405ad.1665583328.git.geert+renesas@glider.be
Add the SASYNCPER internal clock, which is the clock source of the
various SASYNCPERD[124] clocks, to match the clock tree diagram in the
documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/18e6765bfc3bf7c3ee5ce93a370d377c1d17728e.1665558014.git.geert+renesas@glider.be
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231253.15592-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231013.14791-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCY1kNmwAKCRCKwlD9ZEnx
cHGMAP90gnxw9QtkoODnLu2MbcdNNoB/AFeY4O6snbGcwJTYEQD9GqBXxZ3rhZtR
t34KBpENqFdv5HByIxKQ0OT+yYRZew0=
=oXTL
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-fixes-for-v6.1-tag1'
clk: renesas: Fixes for v6.1
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
Currently, determine_rate() is not doing any round operation
and due to this it always selects a lower clock source compared
to the closest higher one.
Support sd clk mux round operation by passing
CLK_MUX_ROUND_CLOSEST flag to clk_mux_determine_rate_flags().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220919084110.3065156-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IIC groups clock and reset entries to CPG driver.
IIC Group A consists of IIC0 and IIC1. IIC Group B consists of
IIC2 and IIC3. To confuse things, IIC_PCLK0 is used by group A
and IIC_PCLK1 is used by group B.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220819193944.337599-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add conditional compilation for struct r9a07g044_cpg_info, so the
compiler won't allocate any memory for this variable in case
CONFIG_CLK_R9A07G044 is disabled.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220804082605.157269-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A variable pointing to const isn't const itself. It'd have to contain
"const" keyword after "*" too. Therefore, cpg_pll_config cannot be put
to "rodata". Hence use __initdata instead of __initconst to fix this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[js] more explanatory commit message.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220623083217.26433-2-jslaby@suse.cz
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/Five SoC has almost the same clock structure compared to the
Renesas RZ/G2UL SoC, re-use the r9a07g043-cpg.c file to add support for
RZ/Five SoC.
This patch splits up the clocks and reset arrays for RZ/G2UL and RZ/Five
SoC using #ifdef CONFIG_ARM64 and #ifdef CONFIG_RISCV checks.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220622181723.13033-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The register block base pointer as stored in the reg member of the
rz_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
rz_cpg_register_clock().
After this, the data member is the only remaining member of the rz_cpg
structure, so the whole structure can be replaced by the data member.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2380285576edaa4ad3dc5eca7e0ca418f068c6ef.1654694831.git.geert+renesas@glider.be
All but the data member of the r8a7778_cpg structure are unused, so the
whole structure can be replaced by the single member used.
Remove the mapping of the CPG registers, as no code uses the mapped
registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/4123c1c40a901195f00a825d434553d2052829aa.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
sh73a0_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
sh73a0_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5423e43d0cf518691965412fb510097d23ac5955.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a7740_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a7740_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7ec676bcc36ef1eda02c2db328c527fc5fd44e99.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a73a4_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a73a4_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f835f3dfcf3bf754065e5002663952cc6341caac.1654694831.git.geert+renesas@glider.be
As per RZ/G2L HW(Rev.1.10) manual, reset monitor register value 0 means
reset signal is not applied (deassert state) and 1 means reset signal
is applied (assert state).
reset_control_status() expects a positive value if the reset line is
asserted. But rzg2l_cpg_status function returns zero for asserted
state.
This patch fixes the issue by adding double inverted logic, so that
reset_control_status returns a positive value if the reset line is
asserted.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220531071657.104121-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220518182527.1693156-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New support:
- Tegra gpcdma Driver support
- Qualcomm SM8350, Sm8450 and SC7280 Device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- Deprecate '#dma-channels' & '#dma-requests' bindings
- Driver updates for stm32, ptdma idsx etc
-----BEGIN PGP SIGNATURE-----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=ANxH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
The clock controller device on r9a06g032 takes all the memory range that
is described as being a system controller. This range contains many
different (unrelated?) registers besides the ones belonging to the clock
controller, that can necessitate to be accessed from other peripherals.
For instance, the dmamux registers are there. The dmamux "device" will
be described as a child node of the clock/system controller node, which
means we need the top device driver (the clock controller driver in this
case) to populate its children manually. In case of error when
populating the children, we do not fail the probe on purpose to keep the
clk driver up and running.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-7-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmamux register is located within the system controller.
Without syscon, we need an extra helper in order to give write access to
this register to a dmamux driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-5-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add ethernet clock/reset entries to CPG driver.
Note that the AXI and CHI clocks are both enabled and disabled using
the same register bit.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220504145454.71287-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC is very similar to RZ/G2L, though it doesn't have
any CLK_MON registers.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-11-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M doesn't have a matching set of reset monitor regs for each reset
reg like the RZ/G2L. Instead, it has a single CPG_RST_MON reg which has a
single bit per module.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-10-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M SoC doesn't use CLK_MON registers, so make them optional.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-9-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All of the muxes and dividers that can be modified require the HIWORD
flags, so make the macros set them. It won't affect read only muxes and
dividers.
This will make the clock tables a little easier to read, particularly for
new SoCs coming.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-8-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We only ever use ARRAY_SIZE() to populate the number of parents, so
move this into the macro to always detect it automatically. This
also makes the tables of clocks a little simpler.
Similarly for the DEF_SD_MUX macro.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-6-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
M3 clock is sourced from DSI Divider (DSIDIVA * DSIDIVB)
This patch add support for DSI divider clk by combining
DSIDIVA and DSIDIVB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PLL5 generates FOUTPOSTDIV clk and is sourced by LCDC/DSI modules.
The FOUTPOSTDIV is connected to PLL5_4 MUX. Video clock is sourced
from DSI divider which is connected to PLL5_4 MUX.
This patch adds support for generating FOUTPOSTDIV clk.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It needs to be un-gated, but also a reset must be released and an idle
flag should also be disabled.
The driver already supports all these operations, so update the
description of the RTC hclock to fit these requirements.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220421090016.79517-3-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_500 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402074626.25624-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/G2UL is almost identical to RZ/G2L SoC with
fewer IP blocks. The IP blocks such as WDT1, GPT, H264, GPU and POEG are
not present on RZ/G2UL.
This patch adds minimal clock and reset entries required to boot the
system on Renesas RZ/G2UL SMARC EVK and binds it with the RZ/G2L CPG core
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Describe the various clocks used by the SPI Multi I/O Bus Controller
(RPC-IF) on the R-Car D3 SoC: RPCSRC internal clock, RPC{,D2} clocks
derived from it, and RPC-IF module clock.
The RPCSRC clock divider on R-Car D3 is very similar to the one on R-Car
E3, but uses a different pre-divider for the PLL0 parent. Add a new
macro to describe it, reusing the existing clock type for R-Car E3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3fd1e886b7737cd0e199603bae81d01be9dcf3aa.1648546700.git.geert+renesas@glider.be
Add the module clock used by the RCLK Watchdog Timer (RWDT) on the
Renesas R-Car S4-8 (r8a779f0) SoC. Mark it as a critical clock, to
ensure uninterrupted watchdog operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8d9b280065a663f2cf31db7b21a010aa781a0af1.1642525158.git.geert+renesas@glider.be
According to Section 8.1.2 Figure 8.1.1 ("Block Diagram of CPG"), Note
22 ("RSW2 divider"), and Table 8.1.4d ("Lists of CPG clocks generated
from CPGMA1"), the RSwitch2 and PCI Express clock is generated from PLL5
by dividing by two, followed by the RSW2 divider. As PLL5 runs at 3200
MHz, and RSW2 is fixed to 320 MHz, the RSW2 divider must be 5.
Correct the parent and the fixed divider.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d6a406f31e6f02f892e0253f4e8a9a2f68fd652e.1641566003.git.geert+renesas@glider.be
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the HW manual (Rev.1.00 Sep, 2021) PLL2 and PLL3 should be
1600 MHz, but with current multiplier and divider values this resulted
to 1596 MHz.
This patch updates the multiplier and divider values for PLL2 and PLL3
so that we get the exact (1600 MHz) values.
Fixes: 17f0ff3d49 ("clk: renesas: Add support for R9A07G044 SoC")
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211223093223.4725-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks for MLP modules on Renesas R-Car E3 and D3 SoCs.
Similar to other R-Car Gen3 SoC, exact information on the parents of MLP
clocks on E3 and D3 is not available. However, since the parents of
these clocks are not anyhow software-controllable, the only harm from
this is inexact information exported via debugfs. So just keep the
parent set in the same way as with other Gen3 SoCs.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211225193957.2195012-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of cpg_mssr_add_clk_domain().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of rzg2l_cpg_add_clk_domain().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV divider as per HW manual
Rev.1.00.
This patch adds clock divider table "dtable_1_8" and switches to
DEF_DIV for "I" clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV which controls CPU
frequency. Define CPG_PL1_DDIV, so that we can register it as a
clock divider in later patch.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
This patch removes the old SD handling code and switch to the new one.
This updates the SDHI driver at the same time. Because the SDHI driver
can only communicate with the clock driver via clk_set_rate(), I don't
see an alternative to this flag-day-approach, so we cross subsystems
here.
The patch sadly looks messy for the CPG lib, but it is basically a huge
chunk of code removed and smaller chunks added. It looks much better
when you just view the resulting source file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20211110191610.5664-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211110191610.5664-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macros CLK_PLL2_DIV16->CLK_PLL2_DIV2_8 and
CLK_PLL2_DIV20->CLK_PLL2_DIV2_10 to match the clock tree mentioned in
the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110082019.28554-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make W=1:
drivers/clk/renesas/rzg2l-cpg.c:95: warning: Function parameter or member 'num_resets' not described in 'rzg2l_cpg_priv'
Add the missing kerneldoc for fields in struct rzg2l_cpg_priv and struct
rzg2l_cpg_info related to Module Resets.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/39c2c5fd4232b6620a4a56dba4e2b0d61476ee36.1634646869.git.geert+renesas@glider.be
Add SDHI clk mux support to select SDHI clock from different clock
sources.
As per HW manual, direct clock switching from 533MHz to 400MHz and
vice versa is not recommended. So added support for handling this
in mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007111434.8665-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse this code for V3U soon. Because its RPCCKCR register is
at a different offset, the moved functions do not use the base register
as an argument anymore but the RPCCKCR register itself. Verified that an
Eagle board with R-Car V3M still works.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Z0 and Z1 (Cortex-A76 Sub-system 0 and 1) clocks,
based on the existing support for Z clocks on R-Car Gen3.
As the offsets of the CPG_FRQCRB and CPG_FRQCRC registers on R-Car V3U
differ from the offsets on other R-Car Gen3 SoCs, we cannot use the
existing R-Car Gen3 support as-is. For now, just make a copy, and
change the register offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2112e3bc870580c623bdecfeff8c74739699c610.1625219713.git.geert+renesas@glider.be
The AXI and CHI clocks use the same register bit for controlling clock
output. Add a new clock type for coupled clocks, which sets the
CPG_CLKON_ETH.CLK[01]_ON bit when at least one clock is enabled, and
clears the bit only when both clocks are disabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to handle mux clocks in order to select a clock source
from multiple sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW(Rev.0.50) manual, clock monitor register value
0 means clock is not supplied and 1 means clock is supplied.
This patch fixes the issue by removing the inverted logic.
Fixing the above, triggered following 2 issues
1) GIC interrupts don't work if we disable IA55_CLK and DMAC_ACLK.
Fixed this issue by adding these clocks as critical clocks.
2) DMA is not working, since the DMA driver is not turning on DMAC_PCLK.
So will provide a fix in the DMA driver to turn on DMA_PCLK.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IA55_CLK and DMAC_ACLK as critical clocks.
Previously it worked ok, because of a bug in clock status function
and the following patch in this series fixes the original bug.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Fixes: eb829e549b ("clk: renesas: r9a07g044: Add DMAC clocks/resets")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of data
to describe clks on various SoCs and fix bugs. The other big new thing
in here is the Mediatek MT8192 clk driver. That's been under review for
a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk drivers.
There are some non-clk driver bits in here which have all been acked by
the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML
-----BEGIN PGP SIGNATURE-----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=Rrqg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When configuring a kernel including support for Renesas ARM/ARM64 Socs,
but excluding support for the RZ/N1D SoC, the user is always asked about
the RZ/N1D clock driver. As this driver is already auto-selected when
building a kernel including support for the RZ/N1D SoC, there is no need
to make the CLK_R9A06G032 symbol visible, unless compile-testing.
Align the symbol description with the other symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/4f3d30c730c30546f702715ffc648922a8156703.1628672649.git.geert+renesas@glider.be
The DSI clock is incorrectly defined as a fixed clock. This
demonstrates itself as the dsi-encoders failing to correctly enable and
start their PPI and HS clocks internally, and causes failures.
Move the DSI parent clock to match the updates in the BSP, which
resolves the initialisation procedures.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Link: https://lore.kernel.org/r/20210622232711.3219697-3-kieran.bingham@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DU clock is added to the S3D1 clock parent. The Renesas BSP lists
S2D1 as the clock parent, however there is no S2 clock on this platform.
S3D1 is chosen as a best effort guess and demonstrates functionality but
is not guaranteed to be correct.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20210622232711.3219697-2-kieran.bingham@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix clock index out of range check for module clocks in
rzg2l_cpg_clk_src_twocell_get().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210617155432.18827-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
These functions accidentally return both error pointers and NULL when
there is an error. It doesn't cause a problem but it is confusing and
seems unintentional.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/YMtY7nOtqEvTokh7@mwanda
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The "pll_clk" and "clock" pointers are allocated with devm_kzalloc() so
freeing them with kfree() will lead to a double free. This would only
happen if probe failed, and the system is not bootable.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/YMtYs7LVveYH4eRe@mwanda
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the function returns NULL on error, so exact error code is
lost. This patch changes return convention of the function to use
ERR_PTR() on error instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1623896524-102058-1-git-send-email-yang.lee@linux.alibaba.com
[geert: Drop curly braces]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for P2 clock which is sourced from pll3_div2_4_2.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW Manual(Rev.0.50) P1 is sourced from pll3_div2_4.
So fix the clock definitions for P1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW Manual (Rev.0.50), CPG_PL3A_DDIV,CPG_PL3B_DDIV
and CPG_PL2_DDIV(for P0) shares same divider table entries. Rename
clk_div_table dtable_3b to clk_div_table dtable_1_32 so that it
can be reused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the clock outputs supported by RZ/G2L (R9A07G044) SoC
and bind it with RZ/G2L CPG core.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CPG core wrapper for RZ/G2L family.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 ZA2 clock is from PLL0D3 or S0,
and it can be controlled by ZA2CKCR.
It is needed for R-Car Sound, but is not used so far.
Using default settings is very enough at this point.
This patch adds it by DEF_FIXED().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmxclrmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Realtime Module Stop Control Register definitions (RMSTPCR(i)) are
incorrect for i >= 8 on R-Car Gen2 and Gen3.
As these are unused, and not planned to be used, just like the
corresponding Modem Module Stop Control Register definitions (MMSTPCR())
on R-Mobile APE6 (they are intended for the software running on the
Real-Time and Modem CPU cores), they can just be removed.
Reported-by: Hai Nguyen Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/2d8bc4d9806b419ebb06030d2f31b2ea1e59b1d6.1620119700.git.geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the divider clocks on RZ/N1 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
Note that range checking is not yet implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7a384d02b85cdaac4a0e2b357582c8244b9a6f98.1617282116.git.geert+renesas@glider.be
Currently the .determine_rate() callback considers only the current
parent clock, limiting the range of achievable clock rates on DIV6
clocks with multiple parents, as found on SH/R-Mobile SoCs.
Extend the callback to consider all available parent clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/60e639692b462f99e0b6ab868c3675b3d97dbdb0.1617281699.git.geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the DIV6 clocks on SH/R-Mobile and R-Car
SoCs from the old .round_rate() callback to the newer .determine_rate()
callback, which does not suffer from this limitation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fd8c45cd8bf5c6d928ca69c8b669be35b93de09.1617281699.git.geert+renesas@glider.be
The error handling paths after pm_runtime_get_sync() have no refcount
decrement, which leads to refcount leak.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210415073338.22287-1-dinghao.liu@zju.edu.cn
[geert: Remove now unused variable priv]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for switching the Z and Z2 clocks between normal and boost
modes, by requesting clock rate changes to parent PLLs.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-8-geert+renesas@glider.be
Currently the PLLs are modeled as fixed factor clocks, based on initial
settings. However, enabling CPU boost clock rates requires increasing
the PLL clock rates.
Add a custom clock driver to model the PLL clocks. This will allow the
Z (CPU) clock driver to request changing the PLL clock rate.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-7-geert+renesas@glider.be
Improve accuracy in the .determine_rate() callback for Z and Z2 clocks
by using rounded divisions. This is similar to the calculation of rates
and multipliers in the .recalc_rate() resp. set_rate() callbacks.
Sample impact for a few requested clock rates:
- R-Car H3:
- Z 500 MHz: 468 MHz => 515 MHz
- Z2 1000 MHz: 973 MHz => 1011 MHz
- R-Car M3-W:
- Z 500 MHz: 422 MHz => 516 MHz
- Z2 800 MHz: 750 MHz => 788 MHz
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-6-geert+renesas@glider.be
Due to the clamping of mult, "(32 - mult) << __ffs(zclk->mask)" can
never exceed the mask.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-4-geert+renesas@glider.be
cpg_z_clk.mask contains a mask for a 32-bit register.
Hence its size can be reduced from unsigned long to u32.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-3-geert+renesas@glider.be
The fixed divider in the calculation of the Z and Z2 clock rates was
generalized from a hardcoded value of two to a parameterized value, but
the comments were not updated accordingly.
Fixes: 20cc05ba04 ("clk: renesas: rcar-gen3: Parameterise Z and Z2 clock fixed divisor")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-2-geert+renesas@glider.be
As clk_core_populate_parent_map() checks clk_init_data.num_parents
first, and checks clk_init_data.parent_names[] before
clk_init_data.parent_data[] and clk_init_data.parent_hws[], leaving the
latter uninitialized doesn't do harm for now. However, it is better to
play it safe, and initialize all clk_init_data structures to zeroes, to
avoid any current and future members containing uninitialized data.
Remove a few explicit zero initializers, which are now superfluous.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210326105434.1574796-1-geert+renesas@glider.be
Fixes the following W=1 kernel build warning(s):
drivers/clk/renesas/renesas-cpg-mssr.c:168: warning: Function parameter or member 'smstpcr_saved' not described in 'cpg_mssr_priv'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-12-lee.jones@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V3U has a CPG different enough to not be a generic Gen3 CPG but
similar enough to reuse code. Introduce a new CPG library, factor out
the SD clock handling and hook it to the generic Gen3 CPG driver so we
have an equal state. V3U will make use of it in the next patch then.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201227174202.40834-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse SD clock handling for other SoCs and, thus, need to
generalize it. So, don't access cpg_quirks in that realm.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201227174202.40834-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clocks used by the Pin Function Controller (PFC) and
General Purpose Input/Output (GPIO) blocks, and their parent clock CP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-4-geert+renesas@glider.be
According to Figure 8.1.1 ("Block Diagram of CPG (R-Car V3U-AD)") in the
R-Car V3U Series User's Manual Rev. 0.5, the parent of the CBFUSA clock
is EXTAL.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-3-geert+renesas@glider.be
The S2 internal core clock does not exist on R-Car V3U. Remove it.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-2-geert+renesas@glider.be
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
There is no reason to keep on using the __raw_{read,write}l() I/O
accessors in Renesas ARM driver code. Switch to using the plain
{read,write}l() I/O accessors, to have a chance that this works on
big-endian.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201119125053.4065746-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2E (R8A774C0) CPG/MSSR
driver.
Add new clk type CLK_TYPE_GEN3_E3_RPCSRC to register rpcsrc as a fixed
clock on R-Car Gen3 E3 (and also RZ/G2E which is identical to E3 SoC),
parent and the divider is set based on the register value CPG_RPCCKCR[4:3]
which has been set prior to booting the kernel.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201116101002.5986-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car V3U clock driver defines the R and OSC clocks using R-Car Gen3
clock types. However, The R-Car V3U clock driver does not use the R-Car
Gen3 clock driver core, hence registering the R and OSC clocks fails:
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock osc: -22
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock r: -22
Fix this by introducing clock definition macros specific to R-Car V3U.
Note that rcar_r8a779a0_cpg_clk_register() already handled the related
clock types. Drop the now unneeded include of rcar-gen3-cpg.h.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201109152614.2465483-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2N (R8A774B1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2M (R8A774A1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When compiling with clang:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:21: warning: no previous prototype for function 'rcar_r8a779a0_cpg_clk_register' [-Wmissing-prototypes]
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
static
Similarly, with sparse:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:12: warning: symbol 'rcar_r8a779a0_cpg_clk_register' was not declared. Should it be static?
There are no users of rcar_r8a779a0_cpg_clk_register() outside this
file, so it should be static.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200924111808.15358-1-geert+renesas@glider.be
The R9A06G032 clock driver uses an array of packed structures to reduce
kernel size. However, this array contains pointers, which are no longer
aligned naturally, and cannot be relocated on PPC64. Hence when
compile-testing this driver on PPC64 with CONFIG_RELOCATABLE=y (e.g.
PowerPC allyesconfig), the following warnings are produced:
WARNING: 136 bad relocations
c000000000616be3 R_PPC64_UADDR64 .rodata+0x00000000000cf338
c000000000616bfe R_PPC64_UADDR64 .rodata+0x00000000000cf370
...
Fix this by dropping the __packed attribute from the r9a06g032_clkdesc
definition, trading a small size increase for portability.
This increases the 156-entry clock table by 1 byte per entry, but due to
the compiler generating more efficient code for unpacked accesses, the
net size increase is only 76 bytes (gcc 9.3.0 on arm32).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201130085743.1656317-1-geert+renesas@glider.be
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # PowerPC allyesconfig build
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no case (and none foreseen) where we would need to disable the
SDn clock. So, for simplicity, remove its handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200922120036.10298-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rcar-gen3-cpg driver is also used on Renesas RZ/G2 SoC's, update the
description for the CLK_RCAR_GEN3_CPG config symbol to reflect this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200911101703.20521-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for R-Car V3U (r8a779a0), including core, module
clocks, resets, and register access, because register specification
differs from R-Car Gen2/3.
Inspired by patches in the BSP by LUU HOAI.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1599810232-29035-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To support other register layouts in the future, add register pointers
of {control,status,reset,reset_clear}_regs into struct cpg_mssr_priv.
After that, we can remove unused macros like MSTPSR(). No behavioral
changes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1599810232-29035-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
VSP1 instances VSPS (which stands for "VSP Standard") and VSPR (which
stands for "VSP for Resizing") were wrongly named as "vsp1-sy" and
"vsp1-rt". The clock section in the SoC datasheets misunderstood the
abbreviations as meaning VSP System and VSP Realtime, and named the
corresponding clocks VSP1(SY) and VSP1(RT). This mistake has been
carried over to the kernel code.
This patch fixes this by renaming the clock names to "vsps" and "vspr".
Inspired from commit 79ea9934b8 ("ARM: shmobile: r8a7790: Rename
VSP1_(SY|RT) clocks to VSP1_(S|R)")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200831183722.8165-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock entry 130 for VSPR (VSP for Resizing) module, so that this module
can be used on R8A7742 (RZ/G1H) SoC.
Alongside rename clock entry "vsp1-sy" to "vsps" (VSP Standard), so that
VSP1 clock names are in sync.
Note: The entry for VSPR clock was accidentally dropped from RZ/G manual
when all the information related to RT were removed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200831180312.7453-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ensures RWDT remains alert throughout the boot process if enabled.
This patch applies the change to the following SoCs: r8a774a1,
r8a774b1 and r8a774c0.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200616162626.27944-4-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ensures RWDT remains alert throughout the boot process if enabled.
This patch applies the change to the following SoCs: r8a77950, r8a77951,
r8a77960, r8a77961, r8a77965, r8a77970, r8a77980, r8a77990 and r8a77995.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200616162626.27944-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This allows us to add the RWDT clock to the list of critical clocks without
keeping it enabled needlessly if not used.
Changing the semantics of crit_mod_clks in this way is safe for the current
user (INTC-AP) because it is never off at boot time.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200616162626.27944-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On SoCs with Standby Control Registers (STBCRs) instead of Module Stop
Control Registers (MSTPCRs), the suspend handler saves the wrong
registers, and the resume handler prints the wrong register in an error
message.
Fortunately this cannot happen yet, as the suspend/resume code is used
on PSCI systems only, and systems with STBCRs (RZ/A1 and RZ/A2) do not
use PSCI. Still, it is better to fix this, to avoid this becoming a
problem in the future.
Distinguish between STBCRs and MSTPCRs where needed. Replace the
useless printing of the virtual register address in the resume error
message by printing the register index.
Fixes: fde35c9c7d ("clk: renesas: cpg-mssr: Add R7S9210 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507074713.30113-1-geert+renesas@glider.be
CLK_RENESAS_CPG_MSSR selects CLK_RENESAS_DIV6, and CLK_RCAR_GEN2_CPG
selects CLK_RENESAS_CPG_MSSR, so there is no longer a need for the
individual R-Car Gen2 clock driver options to select CLK_RENESAS_DIV6.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200427193446.29738-1-geert+renesas@glider.be
This file seems to be for R9A06G032 only. So replace reference to
R9A09G032 by R9A06G032 to avoid confusion.
AFAIK, R9A09G032 does'nt exist.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200413041709.3630-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112525.5834-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car M3-N (R8A77965)
CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-3-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car M3-W/M3-W+
(R8A7796) CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-2-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car H3 (R8A7795)
CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-1-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CryptoCell module clocks and their parents for the CryptoCell
instances in the various Renesas R-Car Gen3 SoCs that do not have
support for them yet in their clock drivers (M3-W/W+, M3-N, E3, D3).
The R-Car H3 clock driver already supports these clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200124133137.15921-1-geert+renesas@glider.be
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
Despite using the same compatible values ("r8a7795"-based) because of
historical reasons, R-Car H3 ES1.x (R8A77950) and R-Car H3 ES2.0+
(R8A77951) are really different SoCs, with different part numbers.
Hence the SoC configuration symbol will be split in two separate config
symbols.
As the Clock Pulse Generator / Module Standby and Software Reset blocks
in both SoCs are very similar, they will keep on sharing a driver.
Extend the dependency of CONFIG_CLK_R8A7795, to prepare for the split.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191230080902.2832-1-geert+renesas@glider.be
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
I was unable to get clk_set_rate() setting a lower RPC-IF clock frequency
and that issue boiled down to me not passing CLK_SET_RATE_PARENT flag to
clk_register_composite() when registering the RPC[D2] clocks...
Fixes: db4a0073cc ("clk: renesas: rcar-gen3: Add RPC clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/be27a344-d8bf-9e0c-8950-2d1b48498496@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All multipliers and dividers are small.
Storing them in u8 instead of unsigned int reduces kernel size for a
generic kernel by ca. 0.5 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191206133254.23800-1-geert+renesas@glider.be
Add support for the R-Car M3-W+ (R8A77961) SoC to the Renesas Clock
Pulse Generator / Module Standby and Software Reset driver.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver. R-Car M3-W+ lacks a few modules, so their
clocks must be nullified.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122941.12342-5-geert+renesas@glider.be
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Extend the dependency of CONFIG_CLK_R8A77960 from CONFIG_ARCH_R8A7796 to
CONFIG_ARCH_R8A77960, to relax dependencies for a future rename of the
SoC configuration symbol.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122941.12342-4-geert+renesas@glider.be
There is no need to terminate a function with a semicolon. Remove it.
Reported-by: Biju Das <biju.das@bp.renesas.com>
Fixes: 7ce36da900 ("clk: renesas: cpg-mssr: Add support for R-Car M3-N")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191016150711.30305-1-geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the SD clocks on R-Car Gen3 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
This includes implementing range checking.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190830134515.11925-9-geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the Z clocks on R-Car Gen3 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
This includes implementing range checking.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190830134515.11925-8-geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the Z clock on R-Car Gen2 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
This includes implementing range checking.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190830134515.11925-7-geert+renesas@glider.be
cpg_sd_clock_round_rate() really needs the best rate, not the best
divider. Hence change the iteration to find the former, and get rid of
the final division.
Add an out-of-range rate check while at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20190830134515.11925-6-geert+renesas@glider.be
cpg_sd_clock_round_rate() is the sole caller of cpg_sd_clock_calc_div(),
hence absorb the latter into the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20190830134515.11925-5-geert+renesas@glider.be
The .set_rate() callback for the SD clocks is always called with a valid
clock rate, returned by .round_rate(). Hence there is no need to
iterate through the divider table twice: once to repeat the work done by
.round_rate(), and a second time to find the corresponding divider
entry.
Just iterate once, looking for the divider that matches the passed clock
rate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20190830134515.11925-4-geert+renesas@glider.be
- Use div64_ul() instead of div_u64() if the divisor is unsigned long,
to avoid truncation to 32-bit on 64-bit platforms,
- Use div_u64() for 64-by-32 divisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20190830134515.11925-3-geert+renesas@glider.be
- Use div64_ul() instead of div_u64() if the divisor is unsigned long,
to avoid truncation to 32-bit on 64-bit platforms,
- Prefer ULL constant suffixes over casts to u64,
- Prioritize multiplication over division, to increase accuracy.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20190830134515.11925-2-geert+renesas@glider.be
As of commit 362b334b17 ("ARM: dts: r8a7791: Convert to new
CPG/MSSR bindings"), all upstream R-Car Gen2 device tree source files
use the unified "Renesas Clock Pulse Generator / Module Standby and
Software Reset" DT bindings.
Hence remove backward compatibility with old R-Car Gen2 device trees
describing a hierarchical representation of the various CPG and MSTP
clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190830133615.11274-1-geert+renesas@glider.be
A NULL pointer would be passed to a call of the function kfree()
directly after a call of the function kzalloc() failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/e66b822b-026b-29cc-e461-6334aafd1d30@web.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----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=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
The CPG/MSSR Clock Domain driver does not implement the
generic_pm_domain.power_{on,off}() callbacks, as the domain itself
cannot be powered down. Hence the domain should be marked as always-on
by setting the GENPD_FLAG_ALWAYS_ON flag, to prevent the core PM Domain
code from considering it for power-off, and doing unnessary processing.
Note that this only affects RZ/A2 SoCs. On R-Car Gen2 and Gen3 SoCs,
the R-Car SYSC driver handles Clock Domain creation, and offloads only
device attachment/detachment to the CPG/MSSR driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The RZ/N1 Clock Domain driver does not implement the
generic_pm_domain.power_{on,off}() callbacks, as the domain itself
cannot be powered down. Hence the domain should be marked as always-on
by setting the GENPD_FLAG_ALWAYS_ON flag, to prevent the core PM Domain
code from considering it for power-off, and doing unnessary processing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The CPG/MSTP Clock Domain driver does not implement the
generic_pm_domain.power_{on,off}() callbacks, as the domain itself
cannot be powered down. Hence the domain should be marked as always-on
by setting the GENPD_FLAG_ALWAYS_ON flag, to prevent the core PM Domain
code from considering it for power-off, and doing unnessary processing.
This also gets rid of a boot warning when the Clock Domain contains an
IRQ-safe device, e.g. on RZ/A1:
sh_mtu2 fcff0000.timer: PM domain cpg_clocks will not be powered off
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of open-coding
the same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
The module reset code in the Renesas CPG/MSSR driver uses
read-modify-write (RMW) operations to write to a Software Reset Register
(SRCRn), and simple writes to write to a Software Reset Clearing
Register (SRSTCLRn), as was mandated by the R-Car Gen2 and Gen3 Hardware
User's Manuals.
However, this may cause a race condition when two devices are reset in
parallel: if the reset for device A completes in the middle of the RMW
operation for device B, device A may be reset again, causing subtle
failures (e.g. i2c timeouts):
thread A thread B
-------- --------
val = SRCRn
val |= bit A
SRCRn = val
delay
val = SRCRn (bit A is set)
SRSTCLRn = bit A
(bit A in SRCRn is cleared)
val |= bit B
SRCRn = val (bit A and B are set)
This can be reproduced on e.g. Salvator-XS using:
$ while true; do i2cdump -f -y 4 0x6A b > /dev/null; done &
$ while true; do i2cdump -f -y 2 0x10 b > /dev/null; done &
i2c-rcar e6510000.i2c: error -110 : 40000002
i2c-rcar e66d8000.i2c: error -110 : 40000002
According to the R-Car Gen3 Hardware Manual Errata for Rev.
0.80 of Feb 28, 2018, reflected in Rev. 1.00 of the R-Car Gen3 Hardware
User's Manual, writes to SRCRn do not require read-modify-write cycles.
Note that the R-Car Gen2 Hardware User's Manual has not been updated
yet, and still says a read-modify-write sequence is required. According
to the hardware team, the reset hardware block is the same on both R-Car
Gen2 and Gen3, though.
Hence fix the issue by replacing the read-modify-write operations on
SRCRn by simple writes.
Reported-by: Yao Lihua <Lihua.Yao@desay-svautomotive.com>
Fixes: 6197aa65c4 ("clk: renesas: cpg-mssr: Add support for reset control")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
