The clock dividers might be used with clock stop bit enabled or not.
Current tables only support recommended values from the datasheet. This
might result in warnings like below because no valid clock divider is
found. Resulting in a 0 divider.
There are Renesas ARM Trusted Firmware version out there which e.g.
configure 0x201 (shifted logical right by 2: 0x80) and with this match
the added { STPnHCK | 0, 1 }:
https://github.com/renesas-rcar/arm-trusted-firmware/blob/rcar_gen3_v2.3/drivers/renesas/rcar/emmc/emmc_init.c#L108
------------[ cut here ]------------
sd1h: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set
WARNING: CPU: 1 PID: 1 at drivers/clk/clk-divider.c:141 divider_recalc_rate+0x48/0x70
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.52 #1
Hardware name: Custom board based on r8a7796 (DT)
pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : divider_recalc_rate+0x48/0x70
...
------------[ cut here ]------------
Fixes: bb6d3fa98a ("clk: renesas: rcar-gen3: Switch to new SD clock handling")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
[wsa: extended the table to 5 entries, added comments, reword commit message a little]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230928080317.28224-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make r8a7795_core_clks and r8a7795_mod_clks arrays const and align them
with the other clock tables in other *cpg-mssr.c . No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230917095832.39007-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Clarify the content of the r9a06g032_clkdesc structure by naming the
remaining anonymous structures defined inside. Renaming each field and
updating the doc then becomes necessary in order to avoid name
duplications and kdoc warnings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230913203805.465780-2-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Mention the 'dual' structure in the kdoc. This fixes the following
W=1 warning during build:
> drivers/clk/renesas/r9a06g032-clocks.c:119: warning: Function parameter or member 'dual' not described in 'r9a06g032_clkdesc'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309101314.kTRoxND5-lkp@intel.com/
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230913203805.465780-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
flag and mux_flags are intended to keep bit masks. Use u32 type for it.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912045157.177966-15-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use FIELD_GET() for PLL register fields. This is its purpose.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912045157.177966-14-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The bitmask << 16 is anyway set on both branches of if thus move it
before the if and set the lower bits of registers only in case clock is
enabled.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912045157.177966-12-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
core->name already contains the clock name thus, there is no
need to check the GET_SHIFT(core->conf) to decide on it.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912045157.177966-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use for_each_compatible_node() instead of open-coding it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230802091920.3270703-1-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> # samsung
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # versaclock5
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143156.1066339-1-robh@kernel.org
Acked-by: Abel Vesa <abel.vesa@linaro.org> #imx
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Renesas RZ/V2M SoC comes with 6 CSI IPs (CSI0, CSI1, CSI2
CSI3, CSI4, and CSI5), however Linux is only allowed control
of CSI0 and CSI4.
CSI0 shares its reset and PCLK lines with CSI1, CSI2, and CSI3.
CSI4 shares its reset and PCLK lines with CSI5.
This commit adds support for the relevant clocks.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230622113341.657842-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 3DGE and ZG clocks are necessary to support the 3D graphics.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A clock used for the 3D graphics appears to be common
among multiple SoC's, so add a generic gen3 clock
for clocking the graphics. This is similar to the
cpg_z_clk, with a different frequency control register
and different flags. Instead of duplicating the code,
make cpg_z_clk_register into a helper function and
call the help function with the FCR and flags as
a parameter.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230617150302.38477-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas r9a06g032 bitselect clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidates to
trigger that parent change are either the assigned-clock-parents device
tree property or a call to clk_set_rate(), with determine_rate()
figuring out which parent is the best suited for a given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
Similarly, it doesn't look like the device tree using that clock driver
uses any of the assigned-clock properties on that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the determine_rate
implementation to clk_hw_determine_rate_no_reparent(). Indeed, if no
determine_rate implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-31-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As per the RZ/G2L HW(Rev.1.30 May2023) manual, there are no "write enable"
bits in the CPG_SIPLL5_CLK1 register. So fix the CPG_SIPLL5_CLK register
write by removing the "write enable" bits.
Fixes: 1561380ee7 ("clk: renesas: rzg2l: Add FOUTPOSTDIV clk support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230518152334.514922-1-biju.das.jz@bp.renesas.com
[geert: Remove CPG_SIPLL5_CLK1_*_WEN bit definitions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
are a couple patches to the core clk framework, but they're all basically
cleanups or debugging aids. The driver updates and new additions are dominated
in the diffstat by Qualcomm and MediaTek drivers. Qualcomm gained a handful of
new drivers for various SoCs, and MediaTek gained a bunch of drivers for
MT8188. The MediaTek drivers are being modernized as well, so there are
updates all over that vendor's clk drivers. There's also a couple other new clk
drivers in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual collection of
non-critical fixes and cleanups to various clk drivers. It's good to see that
we're getting more cleanups and modernization patches. Maybe one day we'll be
able to properly split clk providers from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574, MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP to
get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code to
common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm SM6375,
MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588
-----BEGIN PGP SIGNATURE-----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=bTtL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing looks out of the ordinary in this batch of clk driver updates.
There are a couple patches to the core clk framework, but they're all
basically cleanups or debugging aids. The driver updates and new
additions are dominated in the diffstat by Qualcomm and MediaTek
drivers. Qualcomm gained a handful of new drivers for various SoCs,
and MediaTek gained a bunch of drivers for MT8188. The MediaTek
drivers are being modernized as well, so there are updates all over
that vendor's clk drivers. There's also a couple other new clk drivers
in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual
collection of non-critical fixes and cleanups to various clk drivers.
It's good to see that we're getting more cleanups and modernization
patches. Maybe one day we'll be able to properly split clk providers
from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574,
MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P
SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent
failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP
to get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code
to common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car
V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm
SM6375, MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip
rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (290 commits)
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
clk: starfive: Delete the redundant dev_set_drvdata() in JH7110 clock drivers
clk: rockchip: rk3588: make gate linked clocks critical
clk: qcom: dispcc-qcm2290: Remove inexistent DSI1PHY clk
clk: qcom: add the GPUCC driver for sa8775p
dt-bindings: clock: qcom: describe the GPUCC clock for SA8775P
clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
clk: qcom: lpassaudiocc-sc7280: Add required gdsc power domain clks in lpass_cc_sc7280_desc
clk: qcom: lpasscc-sc7280: Skip qdsp6ss clock registration
dt-bindings: clock: qcom,sc7280-lpasscc: Add qcom,adsp-pil-mode property
clk: starfive: Avoid casting iomem pointers
clk: microchip: fix potential UAF in auxdev release callback
clk: qcom: rpm: Use managed `of_clk_add_hw_provider()`
clk: mediatek: fhctl: Mark local variables static
clk: sifive: make SiFive clk drivers depend on ARCH_ symbols
clk: uniphier: Use managed `of_clk_add_hw_provider()`
clk: si5351: Use managed `of_clk_add_hw_provider()`
clk: si570: Use managed `of_clk_add_hw_provider()`
clk: si514: Use managed `of_clk_add_hw_provider()`
clk: lmk04832: Use managed `of_clk_add_hw_provider()`
...
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230312161512.2715500-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each entry in the clock table specifies a number of individual bits in
registers, for contolling clock reset, gaiting, etc. These reg/bit were
packed into a u16 to save space. The combined value is difficult to
understand when reviewing the clock table entries.
Introduce a "struct regbit" which still occupies only 16 bits, but
allows the register and bit values to be specified explicitly. Convert
all previous uses of u16 for reg/bit into "struct regbit".
The bulk of this patch converts the clock table to use struct regbit,
making use of the RB() helper macro. The conversion was automated by
script, and as a further verification, the compiled binary of the table
was compared before/after the change (with objdump -D).
The clk_rdesc_set() function now checks for zero reg/bit internally.
This allows callers of that function to remove those checks.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-5-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Drop three unused fields from the clock descriptor structure, and update
the macros for filling such structures accordingly.
The values for such fields are kept in the source code, now unused, in
case they are needed later.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-3-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Several small readability improvements:
- Move enum gate_type definition up and add comments to each field.
- Use this enum instead of generic uint32_t type in clock desc struct.
- Tidy up bitfield syntax and comments in clock desc structure
- Reformat macros for building clock desc to have one assignment per line
There is no functional change.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-2-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the parent clock of the Video Input Module (VIN) on R-Car D3
is S3D1. Update the driver to match the documentation.
This has no functional impact, as both S1D2 and S3D1 have the same clock
rate, and are always-on clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/9b655843a260e06fa6f3349cdafac180e2bf38a5.1676368776.git.geert+renesas@glider.be
Add the VIN module clocks, which are used by the VIN modules on the
Renesas R-Car V3H (R8A77980) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211153026.3898491-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the VIN module clocks, which are used by the VIN modules on the
Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the ISPCS0 and ISPCS1 module clocks, which are used by the ISPCS
modules on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CSI core clock and the CSI40 and CSI41 module clocks, which are
used by the CSI-2 Interfaces on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230211143655.3809756-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) on the Renesas R-Car V4H
(R8A779G0) SoC.
Based on a large patch in the BSP by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/59461effd0d9f7a39e0c91352c87f2b7071b1891.1675958536.git.geert+renesas@glider.be
The SRCR, SRSTCLR, MSTPCR and MSTPSR registers for R-Car V4H (R8A779G0)
each have registers up to offset 0x74.
Update the corresponding arrays.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87a61wanfx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC. Public users only have ES2 onwards.
In addition to the ES1 specific removals, a check for it was added
preventing the machine to boot further. It may otherwise inherit wrong
clock settings from ES2 which could damage the hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230202092332.2504-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87v8l3z3y8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87tu0nz3xr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PLLs are modeled as fixed factor clocks, based on initial
settings. However, enabling CPU boost clock rates requires increasing
the PLL clock rates.
Add a custom clock driver to model the PLL clocks on R-Car Gen4, and use
it for PLL2 on R-Car V4H. This allows the Z clock (Cortex-A76 core
clock) to request PLL rate changes, and enable boost mode for the High
Performance mode. For now this is limited to integer multiplication
modes.
Note that the definition for CPG_PLLxCR0_NI uses the value for R-Car V4H.
On R-Car S4-8, the integer and fractional multiplication fields are one
bit larger resp. smaller, but R-Car S4-8 does not support High
Performance mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/76a5952900a6e15604c640bc8a27762e0e936677.1670492384.git.geert+renesas@glider.be
The CFG_USB[H2MODE] allows to switch the USB configuration. The
configuration supported are:
- One host and one device
or
- Two hosts
Set CFG_USB[H2MODE] based on the USBF controller (USB device)
availability.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-3-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If cpg_mssr_common_init() fails after assigning priv to global variable
cpg_mssr_priv, it deallocates priv, but cpg_mssr_priv keeps dangling
pointer that potentially can be used later.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f7db7bbf0 ("clk: renesas: cpg-mssr: Add early clock support")
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1671806417-32623-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CRU clock and reset entries to CPG driver.
CRU_SYSCLK and CRU_VCLK clocks need to be turned ON/OFF in particular
sequence for the CRU block hence add these clocks to
r9a07g044_no_pm_mod_clks[] array and pass it as part of CPG data for
both RZ/G2L and RZ/V2L SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221221212703.348278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add Compare-Match Timer (TIM) clock and reset entries to CPG
driver.
The TIM IP on the RZ/V2M comes with 32 channels, but the ISP has
full control of channels 0 to 7, and channels 24 to 31. Therefore
Linux is only allowed to use channels 8 to 23.
The TIM has shared peripheral clock with other modules, so mark it
as critical clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221205145955.391526-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks related to display which are needed to get the DSI output
working.
Extracted from Renesas BSP tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221201095631.89448-4-tomi.valkeinen+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the table in Note 5 for the OSC clock in Table 8.1.4e
("Lists of CPG clocks generated from PLL5") of the R-Car V4H Series
Hardware User's Manual Rev. 0.54, the predividers for the OSC clock are
16 resp. 32 when using a 16.66 resp. 33.33 MHz external crystal.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/dcd572acc584c237f70d2309e038f25040236a87.1669740722.git.geert+renesas@glider.be
Add PWM{8..14} clock and reset entries to CPG driver.
The PWM IP on the RZ/V2M comes with 16 channels, but the ISP has
full control of channels 0 to 7, and channel 15, therefore Linux
is only allowed to use channels 8 to 14.
The PWM channel 15 shares apb clock and reset with PWM{8..14}.
The reset is deasserted by the bootloader/ISP.
Add PWM{8..14} clocks to CPG driver and mark apb clock as
critical clock, so that the apb clock will be always on.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221124191643.3193423-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RSwitch2 and EtherTSN-IF clocks were accidentally mixed up.
While at it, rename them to better match the (future) documentation.
Fixes: a3b4137a4d ("clk: renesas: r8a779f0: Add Ethernet Switch clocks")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/99b8b41bd2c5043c9e457862ef4bc144869eca58.1668501212.git.geert+renesas@glider.be
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the SCIF modules from the S0D12_PER
clock to the SASYNCPERD4 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 080bcd8d59 ("clk: renesas: r8a779f0: Add HSCIF clocks")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If condition (clkspec.np != pd->dev.of_node) is true, then the driver
ends up in an endless loop, forever, locking up the machine.
Fixes: aad03a66f9 ("clk: renesas: r9a06g032: Add clock domain support")
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20221028113834.7496-1-marex@denx.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are cases where not all CPG_MOD clocks should be assumed to support
PM. For example on the CRU block there is a particular sequence that needs
to be followed to initialize the CSI-2 D-PHY in which individual clocks
need to be turned ON/OFF, due to which Runtime PM support wasn't used by
the CRU CSI-2 driver.
This patch adds support to allow indicating if PM is not supported by the
CPG_MOD clocks. Two new members no_pm_mod_clks and num_no_pm_mod_clks are
added to struct rzg2l_cpg_info so that MOD clocks which do not support PM
can be passed by no_pm_mod_clks[] array and when the driver uses Runtime
PM support the clk ID is matched against the no_pm_mod_clks[] array to see
if the clk is needed to be included as part of Runtime PM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026014227.162121-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix typo pll5_mux_dsi_div_params -> mux_dsi_div_params
Fixes the below warning (make W=1):
drivers/clk/renesas/rzg2l-cpg.c:115: warning: Function parameter or member 'mux_dsi_div_params' not described in 'rzg2l_cpg_priv'
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026012123.159790-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the SPI Multi I/O Bus Controller (RPC-IF)
on the Renesas R-Car V4H (R8A779G0) SoC.
While at it, fix table alignment in the definition of the related
RPCSRC internal clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f0609c82e742865be753b67a0a6080f193f405ad.1665583328.git.geert+renesas@glider.be
Add the SASYNCPER internal clock, which is the clock source of the
various SASYNCPERD[124] clocks, to match the clock tree diagram in the
documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/18e6765bfc3bf7c3ee5ce93a370d377c1d17728e.1665558014.git.geert+renesas@glider.be
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231253.15592-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231013.14791-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCY1kNmwAKCRCKwlD9ZEnx
cHGMAP90gnxw9QtkoODnLu2MbcdNNoB/AFeY4O6snbGcwJTYEQD9GqBXxZ3rhZtR
t34KBpENqFdv5HByIxKQ0OT+yYRZew0=
=oXTL
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-fixes-for-v6.1-tag1'
clk: renesas: Fixes for v6.1
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
Currently, determine_rate() is not doing any round operation
and due to this it always selects a lower clock source compared
to the closest higher one.
Support sd clk mux round operation by passing
CLK_MUX_ROUND_CLOSEST flag to clk_mux_determine_rate_flags().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220919084110.3065156-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IIC groups clock and reset entries to CPG driver.
IIC Group A consists of IIC0 and IIC1. IIC Group B consists of
IIC2 and IIC3. To confuse things, IIC_PCLK0 is used by group A
and IIC_PCLK1 is used by group B.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220819193944.337599-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add conditional compilation for struct r9a07g044_cpg_info, so the
compiler won't allocate any memory for this variable in case
CONFIG_CLK_R9A07G044 is disabled.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220804082605.157269-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A variable pointing to const isn't const itself. It'd have to contain
"const" keyword after "*" too. Therefore, cpg_pll_config cannot be put
to "rodata". Hence use __initdata instead of __initconst to fix this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[js] more explanatory commit message.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220623083217.26433-2-jslaby@suse.cz
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/Five SoC has almost the same clock structure compared to the
Renesas RZ/G2UL SoC, re-use the r9a07g043-cpg.c file to add support for
RZ/Five SoC.
This patch splits up the clocks and reset arrays for RZ/G2UL and RZ/Five
SoC using #ifdef CONFIG_ARM64 and #ifdef CONFIG_RISCV checks.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220622181723.13033-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The register block base pointer as stored in the reg member of the
rz_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
rz_cpg_register_clock().
After this, the data member is the only remaining member of the rz_cpg
structure, so the whole structure can be replaced by the data member.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2380285576edaa4ad3dc5eca7e0ca418f068c6ef.1654694831.git.geert+renesas@glider.be
All but the data member of the r8a7778_cpg structure are unused, so the
whole structure can be replaced by the single member used.
Remove the mapping of the CPG registers, as no code uses the mapped
registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/4123c1c40a901195f00a825d434553d2052829aa.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
sh73a0_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
sh73a0_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5423e43d0cf518691965412fb510097d23ac5955.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a7740_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a7740_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7ec676bcc36ef1eda02c2db328c527fc5fd44e99.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a73a4_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a73a4_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f835f3dfcf3bf754065e5002663952cc6341caac.1654694831.git.geert+renesas@glider.be
As per RZ/G2L HW(Rev.1.10) manual, reset monitor register value 0 means
reset signal is not applied (deassert state) and 1 means reset signal
is applied (assert state).
reset_control_status() expects a positive value if the reset line is
asserted. But rzg2l_cpg_status function returns zero for asserted
state.
This patch fixes the issue by adding double inverted logic, so that
reset_control_status returns a positive value if the reset line is
asserted.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220531071657.104121-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220518182527.1693156-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New support:
- Tegra gpcdma Driver support
- Qualcomm SM8350, Sm8450 and SC7280 Device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- Deprecate '#dma-channels' & '#dma-requests' bindings
- Driver updates for stm32, ptdma idsx etc
-----BEGIN PGP SIGNATURE-----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=ANxH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
The clock controller device on r9a06g032 takes all the memory range that
is described as being a system controller. This range contains many
different (unrelated?) registers besides the ones belonging to the clock
controller, that can necessitate to be accessed from other peripherals.
For instance, the dmamux registers are there. The dmamux "device" will
be described as a child node of the clock/system controller node, which
means we need the top device driver (the clock controller driver in this
case) to populate its children manually. In case of error when
populating the children, we do not fail the probe on purpose to keep the
clk driver up and running.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-7-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmamux register is located within the system controller.
Without syscon, we need an extra helper in order to give write access to
this register to a dmamux driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-5-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add ethernet clock/reset entries to CPG driver.
Note that the AXI and CHI clocks are both enabled and disabled using
the same register bit.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220504145454.71287-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC is very similar to RZ/G2L, though it doesn't have
any CLK_MON registers.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-11-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M doesn't have a matching set of reset monitor regs for each reset
reg like the RZ/G2L. Instead, it has a single CPG_RST_MON reg which has a
single bit per module.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-10-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M SoC doesn't use CLK_MON registers, so make them optional.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-9-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All of the muxes and dividers that can be modified require the HIWORD
flags, so make the macros set them. It won't affect read only muxes and
dividers.
This will make the clock tables a little easier to read, particularly for
new SoCs coming.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-8-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We only ever use ARRAY_SIZE() to populate the number of parents, so
move this into the macro to always detect it automatically. This
also makes the tables of clocks a little simpler.
Similarly for the DEF_SD_MUX macro.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-6-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
M3 clock is sourced from DSI Divider (DSIDIVA * DSIDIVB)
This patch add support for DSI divider clk by combining
DSIDIVA and DSIDIVB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PLL5 generates FOUTPOSTDIV clk and is sourced by LCDC/DSI modules.
The FOUTPOSTDIV is connected to PLL5_4 MUX. Video clock is sourced
from DSI divider which is connected to PLL5_4 MUX.
This patch adds support for generating FOUTPOSTDIV clk.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It needs to be un-gated, but also a reset must be released and an idle
flag should also be disabled.
The driver already supports all these operations, so update the
description of the RTC hclock to fit these requirements.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220421090016.79517-3-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_500 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402074626.25624-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/G2UL is almost identical to RZ/G2L SoC with
fewer IP blocks. The IP blocks such as WDT1, GPT, H264, GPU and POEG are
not present on RZ/G2UL.
This patch adds minimal clock and reset entries required to boot the
system on Renesas RZ/G2UL SMARC EVK and binds it with the RZ/G2L CPG core
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Describe the various clocks used by the SPI Multi I/O Bus Controller
(RPC-IF) on the R-Car D3 SoC: RPCSRC internal clock, RPC{,D2} clocks
derived from it, and RPC-IF module clock.
The RPCSRC clock divider on R-Car D3 is very similar to the one on R-Car
E3, but uses a different pre-divider for the PLL0 parent. Add a new
macro to describe it, reusing the existing clock type for R-Car E3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3fd1e886b7737cd0e199603bae81d01be9dcf3aa.1648546700.git.geert+renesas@glider.be
Add the module clock used by the RCLK Watchdog Timer (RWDT) on the
Renesas R-Car S4-8 (r8a779f0) SoC. Mark it as a critical clock, to
ensure uninterrupted watchdog operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8d9b280065a663f2cf31db7b21a010aa781a0af1.1642525158.git.geert+renesas@glider.be
According to Section 8.1.2 Figure 8.1.1 ("Block Diagram of CPG"), Note
22 ("RSW2 divider"), and Table 8.1.4d ("Lists of CPG clocks generated
from CPGMA1"), the RSwitch2 and PCI Express clock is generated from PLL5
by dividing by two, followed by the RSW2 divider. As PLL5 runs at 3200
MHz, and RSW2 is fixed to 320 MHz, the RSW2 divider must be 5.
Correct the parent and the fixed divider.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d6a406f31e6f02f892e0253f4e8a9a2f68fd652e.1641566003.git.geert+renesas@glider.be
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the HW manual (Rev.1.00 Sep, 2021) PLL2 and PLL3 should be
1600 MHz, but with current multiplier and divider values this resulted
to 1596 MHz.
This patch updates the multiplier and divider values for PLL2 and PLL3
so that we get the exact (1600 MHz) values.
Fixes: 17f0ff3d49 ("clk: renesas: Add support for R9A07G044 SoC")
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211223093223.4725-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks for MLP modules on Renesas R-Car E3 and D3 SoCs.
Similar to other R-Car Gen3 SoC, exact information on the parents of MLP
clocks on E3 and D3 is not available. However, since the parents of
these clocks are not anyhow software-controllable, the only harm from
this is inexact information exported via debugfs. So just keep the
parent set in the same way as with other Gen3 SoCs.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211225193957.2195012-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of cpg_mssr_add_clk_domain().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of rzg2l_cpg_add_clk_domain().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV divider as per HW manual
Rev.1.00.
This patch adds clock divider table "dtable_1_8" and switches to
DEF_DIV for "I" clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV which controls CPU
frequency. Define CPG_PL1_DDIV, so that we can register it as a
clock divider in later patch.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
This patch removes the old SD handling code and switch to the new one.
This updates the SDHI driver at the same time. Because the SDHI driver
can only communicate with the clock driver via clk_set_rate(), I don't
see an alternative to this flag-day-approach, so we cross subsystems
here.
The patch sadly looks messy for the CPG lib, but it is basically a huge
chunk of code removed and smaller chunks added. It looks much better
when you just view the resulting source file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20211110191610.5664-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211110191610.5664-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macros CLK_PLL2_DIV16->CLK_PLL2_DIV2_8 and
CLK_PLL2_DIV20->CLK_PLL2_DIV2_10 to match the clock tree mentioned in
the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110082019.28554-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make W=1:
drivers/clk/renesas/rzg2l-cpg.c:95: warning: Function parameter or member 'num_resets' not described in 'rzg2l_cpg_priv'
Add the missing kerneldoc for fields in struct rzg2l_cpg_priv and struct
rzg2l_cpg_info related to Module Resets.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/39c2c5fd4232b6620a4a56dba4e2b0d61476ee36.1634646869.git.geert+renesas@glider.be
Add SDHI clk mux support to select SDHI clock from different clock
sources.
As per HW manual, direct clock switching from 533MHz to 400MHz and
vice versa is not recommended. So added support for handling this
in mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007111434.8665-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse this code for V3U soon. Because its RPCCKCR register is
at a different offset, the moved functions do not use the base register
as an argument anymore but the RPCCKCR register itself. Verified that an
Eagle board with R-Car V3M still works.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Z0 and Z1 (Cortex-A76 Sub-system 0 and 1) clocks,
based on the existing support for Z clocks on R-Car Gen3.
As the offsets of the CPG_FRQCRB and CPG_FRQCRC registers on R-Car V3U
differ from the offsets on other R-Car Gen3 SoCs, we cannot use the
existing R-Car Gen3 support as-is. For now, just make a copy, and
change the register offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2112e3bc870580c623bdecfeff8c74739699c610.1625219713.git.geert+renesas@glider.be
The AXI and CHI clocks use the same register bit for controlling clock
output. Add a new clock type for coupled clocks, which sets the
CPG_CLKON_ETH.CLK[01]_ON bit when at least one clock is enabled, and
clears the bit only when both clocks are disabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to handle mux clocks in order to select a clock source
from multiple sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW(Rev.0.50) manual, clock monitor register value
0 means clock is not supplied and 1 means clock is supplied.
This patch fixes the issue by removing the inverted logic.
Fixing the above, triggered following 2 issues
1) GIC interrupts don't work if we disable IA55_CLK and DMAC_ACLK.
Fixed this issue by adding these clocks as critical clocks.
2) DMA is not working, since the DMA driver is not turning on DMAC_PCLK.
So will provide a fix in the DMA driver to turn on DMA_PCLK.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IA55_CLK and DMAC_ACLK as critical clocks.
Previously it worked ok, because of a bug in clock status function
and the following patch in this series fixes the original bug.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Fixes: eb829e549b ("clk: renesas: r9a07g044: Add DMAC clocks/resets")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of data
to describe clks on various SoCs and fix bugs. The other big new thing
in here is the Mediatek MT8192 clk driver. That's been under review for
a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk drivers.
There are some non-clk driver bits in here which have all been acked by
the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML
-----BEGIN PGP SIGNATURE-----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=Rrqg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When configuring a kernel including support for Renesas ARM/ARM64 Socs,
but excluding support for the RZ/N1D SoC, the user is always asked about
the RZ/N1D clock driver. As this driver is already auto-selected when
building a kernel including support for the RZ/N1D SoC, there is no need
to make the CLK_R9A06G032 symbol visible, unless compile-testing.
Align the symbol description with the other symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/4f3d30c730c30546f702715ffc648922a8156703.1628672649.git.geert+renesas@glider.be
The DSI clock is incorrectly defined as a fixed clock. This
demonstrates itself as the dsi-encoders failing to correctly enable and
start their PPI and HS clocks internally, and causes failures.
Move the DSI parent clock to match the updates in the BSP, which
resolves the initialisation procedures.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Link: https://lore.kernel.org/r/20210622232711.3219697-3-kieran.bingham@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DU clock is added to the S3D1 clock parent. The Renesas BSP lists
S2D1 as the clock parent, however there is no S2 clock on this platform.
S3D1 is chosen as a best effort guess and demonstrates functionality but
is not guaranteed to be correct.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20210622232711.3219697-2-kieran.bingham@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix clock index out of range check for module clocks in
rzg2l_cpg_clk_src_twocell_get().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210617155432.18827-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
These functions accidentally return both error pointers and NULL when
there is an error. It doesn't cause a problem but it is confusing and
seems unintentional.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/YMtY7nOtqEvTokh7@mwanda
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The "pll_clk" and "clock" pointers are allocated with devm_kzalloc() so
freeing them with kfree() will lead to a double free. This would only
happen if probe failed, and the system is not bootable.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/YMtYs7LVveYH4eRe@mwanda
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the function returns NULL on error, so exact error code is
lost. This patch changes return convention of the function to use
ERR_PTR() on error instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1623896524-102058-1-git-send-email-yang.lee@linux.alibaba.com
[geert: Drop curly braces]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for P2 clock which is sourced from pll3_div2_4_2.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW Manual(Rev.0.50) P1 is sourced from pll3_div2_4.
So fix the clock definitions for P1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW Manual (Rev.0.50), CPG_PL3A_DDIV,CPG_PL3B_DDIV
and CPG_PL2_DDIV(for P0) shares same divider table entries. Rename
clk_div_table dtable_3b to clk_div_table dtable_1_32 so that it
can be reused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the clock outputs supported by RZ/G2L (R9A07G044) SoC
and bind it with RZ/G2L CPG core.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CPG core wrapper for RZ/G2L family.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 ZA2 clock is from PLL0D3 or S0,
and it can be controlled by ZA2CKCR.
It is needed for R-Car Sound, but is not used so far.
Using default settings is very enough at this point.
This patch adds it by DEF_FIXED().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmxclrmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Realtime Module Stop Control Register definitions (RMSTPCR(i)) are
incorrect for i >= 8 on R-Car Gen2 and Gen3.
As these are unused, and not planned to be used, just like the
corresponding Modem Module Stop Control Register definitions (MMSTPCR())
on R-Mobile APE6 (they are intended for the software running on the
Real-Time and Modem CPU cores), they can just be removed.
Reported-by: Hai Nguyen Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/2d8bc4d9806b419ebb06030d2f31b2ea1e59b1d6.1620119700.git.geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the divider clocks on RZ/N1 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
Note that range checking is not yet implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7a384d02b85cdaac4a0e2b357582c8244b9a6f98.1617282116.git.geert+renesas@glider.be
Currently the .determine_rate() callback considers only the current
parent clock, limiting the range of achievable clock rates on DIV6
clocks with multiple parents, as found on SH/R-Mobile SoCs.
Extend the callback to consider all available parent clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/60e639692b462f99e0b6ab868c3675b3d97dbdb0.1617281699.git.geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the DIV6 clocks on SH/R-Mobile and R-Car
SoCs from the old .round_rate() callback to the newer .determine_rate()
callback, which does not suffer from this limitation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fd8c45cd8bf5c6d928ca69c8b669be35b93de09.1617281699.git.geert+renesas@glider.be
