Introduce device tree overlays for supporting the eMMC (RTK0EF0186B02000BJ)
and microSD (RTK0EF0186B01000BJ) sub-boards connected via the CN15
connector on the RZ/V2H and RZ/V2N evaluation kits.
These overlays enable SDHI0 with appropriate pin control settings, power
regulators, and GPIO handling. Both sub-boards are supported using shared
overlay files that can be applied to either EVK due to their identical
connector layout and interface support.
To support this, new DT overlay files are added:
- `rzv2-evk-cn15-emmc.dtso` for eMMC
- `rzv2-evk-cn15-sd.dtso` for microSD
Additionally, the base DTS files for both EVKs are updated to include a
fixed 1.8V regulator (`reg_1p8v`) needed by the eMMC sub-board and
potential future use cases such as HDMI output.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250627193742.110818-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Renesas RAA215300 PMIC to the RZ/V2N EVK. The PMIC is
connected to I2C8 and uses a 32.768kHz fixed clock source (x6).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250619135539.207828-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable OSTM0-OSTM7 instances in the RZ/V2N EVK device tree so that all
eight OSTM general timers are active and available.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the initial device tree for the Renesas RZ/V2N EVK board, based on
the R9A09G056N48 SoC. Enable basic board functionality, including:
- Memory mapping (reserve the first 128MB for the secure area)
- Clock inputs (QEXTAL, RTXIN, AUDIO_EXTAL)
- PINCTRL configurations for peripherals
- Serial console (SCIF)
- SDHI1 with power control and UHS modes
Update the Makefile to include the new DTB.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-13-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
