Introduce device tree overlays for supporting the eMMC (RTK0EF0186B02000BJ)
and microSD (RTK0EF0186B01000BJ) sub-boards connected via the CN15
connector on the RZ/V2H and RZ/V2N evaluation kits.
These overlays enable SDHI0 with appropriate pin control settings, power
regulators, and GPIO handling. Both sub-boards are supported using shared
overlay files that can be applied to either EVK due to their identical
connector layout and interface support.
To support this, new DT overlay files are added:
- `rzv2-evk-cn15-emmc.dtso` for eMMC
- `rzv2-evk-cn15-sd.dtso` for microSD
Additionally, the base DTS files for both EVKs are updated to include a
fixed 1.8V regulator (`reg_1p8v`) needed by the eMMC sub-board and
potential future use cases such as HDMI output.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250627193742.110818-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, I2C0 and CSI on RZ/G3E SMARC EVK and tie the CSI to the
OV5645 sensor using Device Tree overlay. RZ/G3E SMARK EVK is a RZ/G2L
alike EVK hence reuse rz-smarc-cru-csi-ov5645.dtsi.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-5-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make dtbs:
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #address-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #size-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
The Sparrow Hawk uses the MSIOF module in I2S mode instead of SPI mode,
triggering a conflict between the SPI bus bindings and dtc:
- Serial engines that can be SPI controllers must use "spi" as their
node names,
- Dtc assumes nodes named "spi" are always SPI controllers.
Fix this by disabling this specific warning for this board.
Fixes: ca764d5321 ("arm64: dts: renesas: sparrow-hawk: Add MSIOF Sound support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/20250506192033.77338015@canb.auug.org.au
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/fbad3581f297d5b95a3b2813bbae7dba25a523fd.1747039399.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the initial device tree for the Renesas RZ/V2N EVK board, based on
the R9A09G056N48 SoC. Enable basic board functionality, including:
- Memory mapping (reserve the first 128MB for the secure area)
- Clock inputs (QEXTAL, RTXIN, AUDIO_EXTAL)
- PINCTRL configurations for peripherals
- Serial console (SCIF)
- SDHI1 with power control and UHS modes
Update the Makefile to include the new DTB.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-13-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a DT overlay for SCIF1 (of the Renesas RZ/G3S SoC) routed through
the PMOD1_3A interface available on the Renesas RZ SMARC Carrier II
board.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250120130936.1080069-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
White Hawk Single boards can use the same ARD-AUDIO-DA7212 external
audio board as the White Hawk board stack. Add support for building
DTBs for them, and document the small differences in connector labels.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/7c840b6e08e0af8a6b9bd5516969eb585f16e10a.1733402907.git.geert+renesas@glider.be
The White Hawk Single board with R-Car V4H ES3.0 (R8A779G3) uses an
updated version of the R-Car V4H (R8A779G0) SoC.
For now, there are no visible differences compared to the variant
equipped with an R-Car V4H ES2.0 (R8A779G2) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/66d0fe78c393e6df2775287c730464e91732ec56.1733156661.git.geert+renesas@glider.be
Enable the Display Unit and link with the HDMI add-on board connected
to the parallel connector on the RZ/G2UL SMARC EVK by using a Device
Tree overlay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240826101648.176647-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Eagle board supports an optional "Function expansion board".
The expansion board adds support for HDMI OUT, HDMI capture from two
different sources, and eMMC.
This change only adds support for the two HDMI capture sources.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240224191902.2065733-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU and CSI on RZ/G2UL SMARC EVK and tie the CSI to the OV5645
sensor using a Device Tree overlay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240213141300.159847-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas Gray Hawk Single board, which is
based on the R-Car V4M (R8A779H0) SoC:
- Memory,
- Crystal oscillators,
- Serial console.
Based on the White Hawk Single DTS, and on a patch for the Gray Hawk
board stack in the BSP by Hai Pham.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/b657402113267acd57aece0b4c681b707e704455.1706194617.git.geert+renesas@glider.be
The White Hawk Single board is a single-board integration of the Renesas
White Hawk CPU and Breakout board stack, based on the R-Car V4H ES2.0
(R8A779G2) SoC.
For now, the only visible differences compared to the board stack are:
- The SoC is an updated version of R-Car V4H (R8A779G0),
- The serial console uses an FT2232H instead of a CP2102 USB-UART
bridge, with CTS/RTS wired.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2b8d37949c17cca170c1d9e97f10a100b20c5cd9.1706192990.git.geert+renesas@glider.be
Add initial support for the R-Car S4 Starter Kit with R8A779F4
SoC support. Based on a patch in the BSP.
Signed-off-by: Michael Dege <michael.dege@renesas.com>
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87pm1wfn8z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/G2LC SMARC EVK and tie the CSI to the OV5645 sensor
using Device Tree overlay.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230413114016.16068-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/V2L SMARC EVK and tie the CSI to the OV5645 sensor
using Device Tree overlay. RZ/G2L SMARC EVK and RZ/V2L SMARC EVK have the
same connections for connecting the CSI to OV5645 sensor so just reuse
the existing r9a07g044l2-smarc-cru-csi-ov5645.dtso and create a symbolic
link to this file for RZ/V2L SMARC EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230412185608.64628-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/G2L SMARC EVK and tie the CSI to OV5645 sensor
using Device Tree overlay. rz-smarc-cru-csi-ov5645.dtsi is created so
that RZ/G2L alike EVKs can make use of it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230322125648.24948-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable sci0 node using dt overlay and disable can{0,1}-stb-hog
nodes in DT overlay as its pins are shared with sci0 pins.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230321114753.75038-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230307105645.5285-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car Sound support for the White Hawk board with the
ARD-AUDIO-DA7212 external audio board, using a DT overlay.
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87o7p5l9t7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Draak and Ebisu boards support an optional LVDS panel. One
compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20211229193135.28767-4-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Salvator-X and Salvator-XS boards support an optional LVDS panel.
One compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20211229193135.28767-3-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for the Renesas White Hawk CPU and BreakOut boards.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220428135058.597586-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add basic support for RZ/G2UL SMARC EVK (based on R9A07G043U11):
- memory
- External input clock
- CPG
- DMA
- SCIF
It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add basic support for the RZ/V2L SMARC EVK (based on R9A07G054L2):
- memory
- External input clock
- CPG
- Pin controller
- SCIF
- GbEthernet
- Audio Clock
It shares the same carrier board with RZ/G2L with the same pin mapping.
Delete the gpio-hog nodes from pinctrl as they will be added later when
the functionality has been tested.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220110134659.30424-12-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add basic support for the RZ/G2LC SMARC EVK (based on R9A07G044C2):
- memory
- External input clock
- SCIF
- GbEthernet
- Audio Clock
It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211216114305.5842-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for the Renesas Spider CPU and BreakOut boards.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Takehito Nakamura <takehito.nakamura.nx@renesas.com>
Link: https://lore.kernel.org/r/20211201073308.1003945-14-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2H SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM files as the RZ/G2M and RZ/G2N kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-8-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2N SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM as the RZ/G2M.
This SOM has only 2GB of DDR, and beacon-renesom-som.dtsi contains
the base memory node, so an additional memory node isn't necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-7-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
