Add the missing dma-ranges property to the soc node, similar to how it
was done for MT8195 and MT8192.
This allows the entire 16GB of iova range to be used and enables
multimedia processing usages, like vcodec and MIPI camera.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://lore.kernel.org/r/20241001113052.3124869-6-fshao@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Configure GPU regulator supplies and enable GPU for GENIO 700 EVK.
The GPU in MT8390 & MT8188 has two power inputs: "DVDD_GPU" and
"DVDD_SRAM_GPU". In Genio 700 EVK, DVDD_GPU is supplied by
mt6359_vproc2_buck_reg, and DVDD_SRAM_GPU is supplied by
mt6359_vsram_others_ldo_reg.
According to section 5.2 "Recommended Operating Conditions" in
MT8390 IoT Application Processor Datasheet v1.9, The recommended
operating voltage ranges are:
- DVDD_GPU: min 0.55V, max 0.86V, typical 0.75V
- DVDD_SRAM_GPU: min 0.71V, max 0.92V, typical 0.85V
To further optimize power saving, we couple DVDD_SRAM_GPU to
DVDD_GPU according to the following relation:
- For opp-880000000 or lower frequency, keep 0.75V
- For opp-915000000 and higher, DVDD_SRAM_GPU should follow
DVDD_GPU. The exact voltage for DVDD_GPU should be decided by
speed binning.
This rule is derived from the OPP table in the link.
In addition, set the voltage spread to 6250 uV, the step size of
'ldo_vsram_others' regulator of mt6359, otherwise the regulator
set_voltage operation fails.
Link: eedd6aedd4/recipes-kernel/dtbo/mt8390/gpu-mali.dts
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002022138.29241-7-pablo.sun@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The clock index "CLK_APMIXED_MFGPLL" belongs to the "apmixedsys" provider,
so fix the index.
In addition, add a "mfg1" label so following commits could set
domain-supply for MFG1 power domain.
Fixes: eaf73e4224 ("arm64: dts: mediatek: mt8188: Add support for SoC power domains")
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002022138.29241-2-pablo.sun@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Add the sound node which is linked to the MT8365 SoC AFE and
the MT6357 audio codec.
Update the file header.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20240226-audio-i350-v8-5-e80a57d026ce@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add audio front end support of MT8365 SoC.
Update the file header.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20240226-audio-i350-v8-4-e80a57d026ce@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The DPI display interface feeds the external display pipeline. However
the pipeline representation is currently incomplete. Efforts are still
under way to come up with a way to represent the "creative" repurposing
of the DP bridge chip's internal output mux, which is meant to support
USB type-C orientation changes, to output to one of two type-C ports.
Until that is finalized, the external display can't be fully described,
and thus won't work. Even worse, the half complete graph potentially
confuses the OS, breaking the internal display as well.
Disable the external display interface across the whole Corsola family
until the DP / USB Type-C muxing graph binding is ready.
Reported-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Closes: https://lore.kernel.org/linux-mediatek/38a703a9-6efb-456a-a248-1dd3687e526d@gmail.com/
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240821042836.2631815-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The clocks for dp_intf* device nodes are given in the wrong order,
causing the binding validation to fail.
Fixes: 6c2503b585 ("arm64: dts: mt8195: Add dp-intf nodes")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240802070951.1086616-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Corsola firmware reserves the memory region of [0x60000000, 0x61100000)
exclusively for ADSP usage.
But in fact, a 6 MB "hole" of [0x60A00000, 0x61000000) didn't get
assigned to the ADSP node in the Corsola device tree, meaning no audio
tasks can access and utilize that memory section.
Update the reserved ADSP memory region to fill the gap.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240719045823.3264974-1-fshao@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This clock dependency introduced a mutual dependency between mfg_async
power domain and mt8183-mfgcfg clock, and Mediatek has confirmed that
this dependency is not needed. Remove this to avoid potential deadlock.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Fixes: 37fb78b9ae ("arm64: dts: mediatek: Add mt8183 power domains controller")
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240805065051.3129354-1-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Some regulators in the kukui device tree are modeled incorrectly. Some
are missing supplies and some switches are incorrectly modeled as
voltage regulators. A pass-through was incorrectly modeled as a
regulator.
Add supplies where missing, remove voltage constraints for "switches",
and drop the "bl_pp5000" pass-through.
This depends on commit 2a99858c17 ("arm64: dts: mediatek: mt8183-kukui:
Add PMIC regulator supplies") for reg_vsys.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Fixes: f15722c0fe ("arm64: dts: mt8183: Add pwm and backlight node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240625095441.3474194-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981 (Filogic 820) has three on-SoC SPI controllers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240727114828.29558-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT8183's Devicetree describes two eFuse regions: one at 8000000 and
another at 11f10000.
The efuse at 8000000, unlike the one at 11f10000 and the efuse on all
other MediaTek SoCs, does not define any cell, including the
socinfo-data ones which the mtk-efuse driver expects to always be
present, resulting in the following errors in the log:
mtk-socinfo mtk-socinfo.0.auto: error -ENOENT: Failed to get socinfo data
mtk-socinfo mtk-socinfo.0.auto: probe with driver mtk-socinfo failed with error -2
The efuse at 8000000 is disabled by default but enabled on mt8183-kukui.
Since it is unused, and to prevent the errors from being thrown, disable
it on mt8183-kukui.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240803-mtk-socinfo-no-data-probe-err-v3-1-09cfffc7241a@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Inspired by the vendor kernel but adapted to the upstream thermal
driver version.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/20240603-mtk-thermal-mt818x-dtsi-v7-6-8c8e3c7a3643@baylibre.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Inspired by the vendor kernel but adapted to the upstream thermal
driver version.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/20240603-mtk-thermal-mt818x-dtsi-v7-4-8c8e3c7a3643@baylibre.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
xhci1 has both USB 2.0 and USB 3.0 host capabilities. By default both
are assumed to be enabled when the controller is enabled. To disable
either one, an extra property is used.
Since the default has both enabled, both PHYs should also be assigned
to the host controller. If a specific design uses only either one,
the board specific dts file can override the PHY assignment together
with adding the "mediatek,u[23]p-dis-msk" property. This keeps both
changes together.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240731034411.371178-4-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
USB 3.0 on xhci1 is not used, as the controller shares the same PHY as
pcie1. The latter is enabled to support the M.2 PCIe WLAN card on this
design.
Mark USB 3.0 as disabled on this controller using the
"mediatek,u3p-dis-msk" property.
Fixes: 96564b1e2e ("arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240731034411.371178-3-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
USB 3.0 on xhci1 is not used, as the controller shares the same PHY as
pcie1. The latter is enabled to support the M.2 PCIe WLAN card on this
design.
Mark USB 3.0 as disabled on this controller using the
"mediatek,u3p-dis-msk" property.
Reported-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> #KernelCI
Closes: https://lore.kernel.org/all/9fce9838-ef87-4d1b-b3df-63e1ddb0ec51@notapiano/
Fixes: b6267a396e ("arm64: dts: mediatek: cherry: Enable T-PHYs and USB XHCI controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240731034411.371178-2-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
While the MDP3 DMA controller can look for the SCP node based on
compatible, it's best practice to supply the MDP3 node with a phandle to
the SCP since that allows supporting dual core SCP as well. Besides,
relying on the compatible search causes an error to be printed, since
the phandle is tried first:
mtk-mdp3 14001000.dma-controller: can't get SCP node
Add the missing phandle to follow the best practice and get rid of the
error.
Fixes: 5710462a11 ("arm64: dts: mediatek: mt8195: add MDP3 nodes")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240606-mt8195-dma-scp-node-err-v2-1-e14702e9d3f2@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Currently the Jacuzzi dtsi file redeclares the full DSI endpoint tree
from the DSI controller just to replace the remote endpoint. This is
not necessary since the local endpoint already has a label that can be
referenced. This will also confusion when the inherited layout is
changed.
Replace the redeclared DSI endpoint tree with a label reference.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240625095705.3474713-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Commit 970c3a6b7a ("mfd: cros_ec: Register keyboard backlight
subdevice") introduced support for detecting keyboard backlight
fuctionality through communication with the ChromeOS EC. This means that
the DT node is no longer used. Remove the unneeded node.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240722-cros-backlight-dt-probe-v2-1-d77cdf7018ec@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
GPIOs 34 and 35 on MT8195 are of type MTK_PULL_PU_PD_RSEL_TYPE, meaning
not only can they be configured as pull-up or pull-down, but the pull
resistance can also be configured.
The current bias setting however doesn't specify a resistance value,
resulting on the following errors:
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 1 Ohm for pin = 34 (GPIO34)
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 1 Ohm for pin = 35 (GPIO35)
Specify the pull resistance for those GPIOs to fix the errors.
Fixes: 5bf7dabe40 ("arm64: dts: mediatek: cherry: Document gpios and add default pin config")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240531-tomato-rsel-gpio34-35-fix-v1-1-64ab2545f182@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add support for the ADC on MT6357/8/9 and keep it default enabled
as this IP is always present on those PMICs.
Users may use different IIO channels depending on board-specific
routing.
Link: https://lore.kernel.org/r/20240604123008.327424-6-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The speedbin eFuse reads a value 'x' from 0 to 7 and, in order to
make that compatible with opp-supported-hw, it gets post processed
as BIT(x).
Change all of the 0x30 supported-hw to 0x20 to avoid getting
duplicate OPPs for speedbin 4, and also change all of the 0x8 to
0xcf because speedbins different from 4 and 5 do support 900MHz,
950MHz, 1000MHz with the higher voltage of 850mV, 900mV, 950mV
respectively.
Fixes: f38ea593ad ("arm64: dts: mediatek: mt8186: Wire up GPU voltage/frequency scaling")
Link: https://lore.kernel.org/r/20240725072243.173104-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On some devicetrees, the drive-strength property gets assigned a
MTK_DRIVE_(x)_mA definition, which matches with (x).
For example, MTK_DRIVE_8mA equals to 8 and MTK_DRIVE_30mA equals
to 30.
Also keeping in mind that the drive-strength property is, by
(binding) definition, taking a number in milliamperes unit,
change all devicetrees to avoid the usage of any MTK_DRIVE_(x)
definition.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240620101656.1096374-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
After commit 868ff5f494
("net: dsa: mt7530-mdio: read PHY address of switch from device tree")
the mt7531 switch on Bananapi-R64 was not detected.
mt7530-mdio mdio-bus:00: reset timeout
mt7530-mdio mdio-bus:00: probe with driver mt7530-mdio failed with error -110
Fix this by adding phy address in devicetree.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20240516204847.171029-1-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add device trees for the MT8186 based Voltorb Chromebooks, also known
as the Acer Chromebook 311 (C723/C723T). The devices are clamshell
style laptops with an optional touchscreen.
The devices differ from the other existing MT8186 Chromebooks in that
it uses a higher speced / binned SoC which also requires a separate
PMIC for the big core cluster. Also, a different codec is used for
the internal speakers.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240620094746.2404753-4-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add DTC_FLAGS '-@' for mt7986a-bananapi-bpi-r3 and -mini to
instruct the devicetree compiler to enable generation of symbols.
This allows proper support for Device Tree Overlay(s) for those
boards; future boards that need DTBO support are expected to add
their own DTC_FLAGS_{dtb-name}.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240620101830.1097548-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The anx7625 binding requires a "ports" node as a container for the
"port" nodes. The jacuzzi dtsi file is missing it.
Add a "ports" node under the anx7625 node, and move the port related
nodes and properties under it.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240131083931.3970388-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The wake-on-bt and wake-on-wlan nodes don't have a button- or event-
prefix that the gpio-keys binding requires.
Fix up the node names to satisfy the binding. While at it, also fix up
the GPIO overriding structure for the wake-on-wlan node. Instead of
referencing the gpio-keys node and then open coding the node, add a
label for the event node, and use that to reference and override the
GPIO settings.
Fixes: 055ef10ccd ("arm64: dts: mt8183: Add jacuzzi pico/pico6 board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240131084043.3970576-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Lenovo Ideapad C330 Chromebook (MTK) uses G2Touch touchscreen as a
second source component.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20231115043511.2670477-1-treapking@chromium.org
[Angelo: Rebased and added comment]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
According to Documentation/devicetree/bindings/sound/dialog,da7219.yaml,
the value of `dlg,jack-det-rate` property should be "32_64" instead of
"32ms_64ms".
Fixes: dc0ff0fa3a ("ASoC: da7219: Add Jack insertion detection polarity")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Link: https://lore.kernel.org/r/20240613-jack-rate-v2-1-ebc5f9f37931@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
According to AngeloGioacchino Del Regno, the syscon node in PMIC is
neither needed nor used. It looks like a solution to expose some of the
registers of PMIC.
Drop it to solve also incorrect number of entries in the "reg" property
and fix dtbs_check warning:
mt8173-elm.dtb: syscon@c000: reg: [[0, 49152], [0, 264]] is too long
Link: https://lore.kernel.org/all/671a4b1e-3d95-438c-beae-d967e0ad1c77@collabora.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240612092421.52917-3-krzysztof.kozlowski@linaro.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
SoCs should use dedicated compatibles for each of their syscon nodes to
precisely describe the block. Using an incorrect compatible does not
allow to properly match/validate children of the syscon device. Replace
SYSCFG compatible, which does not have children, with a new dedicated
one for SCPSYS block.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240612092421.52917-2-krzysztof.kozlowski@linaro.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The top SCPSYS node is not a power domain provider. It's child
"power-controller" is instead.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240612092421.52917-1-krzysztof.kozlowski@linaro.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981 has one on-SoC I2C controller that differs from recent Mediatek
blocks by having a different SLAVE_ADDR register offset (thus a custom
binding compatible string).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240604063159.29216-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Value "emmc_rst" is a group name and should be part of the "groups"
property.
This fixes:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: pinctrl@10211000: emmc-pins-default:mux:function: ['emmc', 'emmc_rst'] is too long
from schema $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7622-pinctrl.yaml#
arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dtb: pinctrl@10211000: emmc-pins-default:mux:function: ['emmc', 'emmc_rst'] is too long
from schema $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7622-pinctrl.yaml#
Fixes: 3725ba3f55 ("arm64: dts: mt7622: add pinctrl related device nodes")
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240604074916.7929-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7988 has three on-SoC I2C controllers that are the same hardware
blocks as already noticed on MT7981 chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240604064302.487-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7988 has on-SoC controller that can control up to 8 PWM interfaces.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240604064302.487-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
OpenWrt One is the first ever OpenWrt product. It's based on MT7981B
(AKA Filogic 820) and has 1 GiB or DDR4 RAM. The rest of peripherals
remains to be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240527115933.7396-4-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981 (Filogic 820) uses efuse for storing calibration data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240514015154.11206-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Align "clocks" array entries to start at the same column.
Fixes: cf29427573 ("arm64: dts: mediatek: Add initial MT7981B and Xiaomi AX3000T")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240405105030.24559-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Overlay syntactic sugar for generating target-path fragments is
supported by the version of dtc supplied with the kernel since commit
50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc"). Hence convert the Bananapi R3 overlay
devicetree source files to sugar syntax, improving readability.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2fd900a30b5a0f7de4ea68f60bac250794b8cdb4.1716984213.git.geert+renesas@glider.be
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Set off-on-delay-us to 500000 us for pp3300_mipibrdg to make sure it
complies with the panel's unprepare delay (the time to power down
completely) of the power sequence. Explicit configuration on the
regulator node is required because mt8192-asurada uses the same power
supply for the panel and the anx7625 DP bridge.
For example, the power sequence could be violated in this sequence:
1. Bridge on: panel goes off, but regulator doesn't turn off (refcount=1).
2. Bridge off: regulator turns off (refcount=0).
3. Bridge resume -> regulator turns on but the bridge driver doesn't
check the delay.
Or in this sequence:
1. Bridge on: panel goes off. The regulator doesn't turn off (refcount=1),
but the .unprepared_time in panel_edp is still updated.
2. Bridge off, regulator goes off (refcount=0).
3. Panel on, but the panel driver uses the wrong .unprepared_time to check
the unprepare delay.
Fixes: f9f00b1f6b ("arm64: dts: mediatek: asurada: Add display regulators")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240502154455.3427793-1-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add basic support for the Kontron 3.5" single board computer featuring a
Mediatek i1200 SoC (MT8395/MT8195).
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240408080816.4134370-2-mwalle@kernel.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This patch fixes an issue where xhci1 was not functioning properly because
the state and PHY settings were incorrect.
The introduction of the 'force-mode' property in the phy-mtk-tphy driver
allows for the correct initialization of xhci1 by updating the Device Tree
settings accordingly.
The necessary fixup which added support for the 'force-mode' switch in the
phy-mtk-tphy driver.
commit 9b27303003 ("phy: mediatek: tphy: add support force phy mode switch")
Link: https://lore.kernel.org/r/20231211025624.28991-2-chunfeng.yun@mediatek.com
Prior to this fix, the system would exhibit the following probe failure messages
for xhci1:
xhci-mtk 11290000.usb: supply vbus not found, using dummy regulator
xhci-mtk 11290000.usb: uwk - reg:0x400, version:104
xhci-mtk 11290000.usb: xHCI Host Controller
xhci-mtk 11290000.usb: new USB bus registered, assigned bus number 5
xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f)
xhci-mtk 11290000.usb: can't setup: -110
xhci-mtk 11290000.usb: USB bus 5 deregistered
xhci-mtk: probe of 11290000.usb failed with error -110
With the application of this dts fixup, the aforementioned initialization errors
are resolved and xhci1 is working.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20240216095751.4937-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a devicetree for the Cherry Dojo (HP Chromebook x360 13b-ca0002sa)
convertible type machine.
Differences with the already supported Tomato machines include:
- Different speaker amplifiers (Dual MAX98380, one per channel)
- I2C Touchscreen is on a different address (though still a HID device)
- Has NVMe storage on the PCIe0 controller
- Slightly different keyboard top row keymap
Link: https://lore.kernel.org/r/20240314103500.93158-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "mediatek,drive-strength-adv" pin config property has been
deprecated in favor of the generic "drive-strength-microamp" property.
Drop or convert all instances. A value of 0 disables the advanced
mode, which is the hardware default.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240412075516.1199846-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "output-enable" property is set on uart1's RTS pin. This is bogus
because the hardware does not actually have a controllable output
buffer. Secondly, the implementation incorrectly treats this property
as a request to switch the pin to GPIO output. This does not fit the
intended semantic of "output-enable" and it does not have any affect
either because the pin is muxed to the UART function, not the GPIO
function.
Drop the property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240412075613.1200048-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable the PCIe0 PHY to be able to set calibrations read from eFuses,
improving the stability and performance of the PCIe link.
While at it, also enable the T-PHYs for both PCIe1 and for USB, allowing
the USB ports to finally switch to gadget mode if needed, and configure
the VBUS/ID pins of both USB ports for the same.
Link: https://lore.kernel.org/r/20240409114211.310462-5-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The paris pinctrl driver supports specifying the RSEL drive strength
in microamperes as well as internal bits definitions: choose to specify
those in uA to avoid using hardware specific values in device trees.
Link: https://lore.kernel.org/r/20240409114211.310462-4-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
GPIOs 25 and 26 do not support pull-up/pull-down when those are muxed
as I2C6's SDA6/SCL6 lines: set those to bias-disable to avoid warning
messages from the pinctrl driver.
Fixes: 96564b1e2e ("arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board")
Link: https://lore.kernel.org/r/20240409114211.310462-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The thermal zones in MT8183 had cryptic names and all of them, apart
from the cpu-thermal zone, had no thermal trips, hence those were not
probed at all.
Refactor the tzts1..5 and tztsABB thermal zones to add the correct
thermal trips and give them a meaningful name, corresponding to the
actually monitored thermal zone.
While at it, also rename the thermal sensor node to "thermal-sensor".
Now the thermal zones are probing and their temperatures can be read.
Fixes: b325ce3978 ("arm64: dts: mt8183: add thermal zone node")
Link: https://lore.kernel.org/r/20240410083002.1357857-4-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-2-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981 (Filogic 820) is a low cost version of MT7986 (Filogic 830) with
the same watchdog controller. It also comes with on-SoC 802.11ax
wireless.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240221085547.27840-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add bindings of two on-SoC XHCI controllers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213130044.1976-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router. It
has 256 MiB of RAM, some LEDs & buttons and (not described yet) 4
Ethernet ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-5-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981 contains on-SoC PIN controller that is also a GPIO provider.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-4-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The updates this time are a bit smaller than most times, mainly because
it is not totally dominated by new Qualcomm hardware support. Instead,
we larger than average updates for Rockchips, NXP, Allwinner and TI.
The only two new SoCs this time are both from NXP and are minor variants
of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console
and a few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmY+daEACgkQYKtH/8kJ
UieIXxAAya9WFfjgJrkOCJnn/3+4Q9nr4HzvCaKPfvbw2YH8krxuXTAI5xyeoUNY
NMb8qyugi94Xw4Jh3qbAYyvQUXFFNgFTvuTQIGqOBIMSNkPjfghiq45emCr+d1ea
0lsCuu1Mpw62H6038xiyMNJNUFyWjLEoLlLaYqPIZj5/jHiOT1hiKZAB5d3+epzx
IhkWEvnSgDo37o6XEtaijFDpu64khdpcWhS4aOt2nJQAR73YYO+jySqEGVwDW4Ht
VXEim70ckcj1WLhGjNYakwkDIw2It24vndzcnmLLJMq5k+9mIZ7D3RYPJrKYLcZk
/F/hozcYFOxVX0TX+ATwaiKsnUQthvBGEKaaeDTO/VCD87ya6/3FIr7LJezLy4fh
t8Vvmgme0JH0kFczWr36YVxdGk6QolkQvNGawTIqPdj5Guj2eSkDHLYIc0HOOps+
4pDKDLO5MUXrOjtWXYy48zGE+7zF58m3QySwieoJAVF5LbnLuXAevmcL+AjQ+QfK
pBTtyDe6hUHxh5vQHSoY05loQ2dELWBxza+G5lNByYMPX4/qzQHcxeZlF7kMm0t5
XE0T0lG/C25QPKQRa1NQ950WtJDoGIWtF0+Kk0qzRP6WbgkX0Wo/NemSmCmVD4IJ
PM/nQYCkccwdD5TjyUl0ZiS/LVfd54MXFHqcrTU2zOMC+YryZHM=
=SnV4
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"The updates this time are a bit smaller than most times, mainly
because it is not totally dominated by new Qualcomm hardware support.
Instead, we larger than average updates for Rockchips, NXP, Allwinner
and TI. The only two new SoCs this time are both from NXP and are
minor variants of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out
fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console and a
few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines"
* tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (612 commits)
arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address
arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells
arm64: dts: marvell: eDPU: drop redundant address/size-cells
arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible
arm64: dts: rockchip: add rk3588 pcie and php IOMMUs
arm64: dts: rockchip: enable onboard spi flash for rock-3a
arm64: dts: rockchip: add USB-C support to rk3588s-orangepi-5
arm64: dts: rockchip: Enable GPU on Orange Pi 5
arm64: dts: rockchip: enable GPU on khadas-edge2
arm64: dts: rockchip: Add USB3 on Edgeble NCM6A-IO board
arm64: dts: rockchip: Support poweroff on Edgeble Neural Compute Module
arm64: dts: rockchip: Add Radxa ROCK 3C
dt-bindings: arm: rockchip: add Radxa ROCK 3C
arm64: dts: exynos: gs101: specify empty clocks for remaining pinctrl
arm64: dts: exynos: gs101: specify bus clock for pinctrl_hsi2
arm64: dts: exynos: gs101: specify bus clock for pinctrl_peric[01]
arm64: dts: exynos: gs101: specify bus clock for pinctrl (far) alive
arm64: dts: Add/fix /memory node unit-addresses
arm64: dts: qcom: qcs404: fix bluetooth device address
arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader
...
Bluetooth is not a random device connected to the MMC/SD controller. It
is function 2 of the SDIO device.
Fix the address of the bluetooth node. Also fix the node name and drop
the label.
Fixes: 055ef10ccd ("arm64: dts: mt8183: Add jacuzzi pico/pico6 board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The "arm,armv8-pmuv3" compatible is intended only for s/w models. Primarily,
it doesn't provide any detail on uarch specific events.
There's still remaining cases for CPUs without any corresponding PMU
definition and for big.LITTLE systems which only have a single PMU node
(there should be one per core type).
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20240417203853.3212103-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Fixup infracfg clock controller binding
It also acts as reset controller so #reset-cells is required.
2. Use -pins suffix for pinctrl
This fixes:
arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: syscon@10001000: '#reset-cells' is a required property
from schema $id: http://devicetree.org/schemas/arm/mediatek/mediatek,infracfg.yaml#
arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: pinctrl@1000b000: 'eth_default', 'eth_sleep', 'usb0_iddig', 'usb1_iddig' do not match any of the regexes: 'pinctrl-[0-9]+', 'pins$'
from schema $id: http://devicetree.org/schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml#
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240301074741.8362-1-zajec5@gmail.com
[Angelo: Added Fixes tags]
Fixes: 5d4839709c ("arm64: dts: mt2712: Add clock controller device nodes")
Fixes: 1724f4cc51 ("arm64: dts: Add USB3 related nodes for MT2712")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: thermal-zones: cpu-thermal:cooling-maps: 'cpu-active-high', 'cpu-active-low', 'cpu-active-med' do not match any of the regexes: '^map[-a-zA-Z0-9]*$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/thermal-zones.yaml#
Fixes: c26f779a22 ("arm64: dts: mt7986: add pwm-fan and cooling-maps to BPI-R3 dts")
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213061459.17917-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Ethernet block doesn't include or act as a reset controller.
Documentation also doesn't document "#reset-cells" for it.
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: ethernet@15100000: Unevaluated properties are not allowed ('#reset-cells' was unexpected)
from schema $id: http://devicetree.org/schemas/net/mediatek,net.yaml#
Fixes: 082ff36bd5 ("arm64: dts: mediatek: mt7986: introduce ethernet nodes")
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213053739.14387-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Mediatek ethsys controller / syscon binding doesn't allow any subnodes
so "#address-cells" and "#size-cells" are redundant (actually:
disallowed).
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: syscon@15000000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/clock/mediatek,ethsys.yaml#
Fixes: 1f9986b258 ("arm64: dts: mediatek: add clock support for mt7986a")
Cc: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213053739.14387-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Binding doesn't specify "reset-names" property and Linux driver also
doesn't use it.
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: thermal@1100b000: Unevaluated properties are not allowed ('reset-names' was unexpected)
from schema $id: http://devicetree.org/schemas/thermal/mediatek,thermal.yaml#
Fixes: ae457b7679 ("arm64: dts: mt7622: add SoC and peripheral related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-5-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: ethernet@1b100000: compatible: ['mediatek,mt7622-eth', 'mediatek,mt2701-eth', 'syscon'] is too long
from schema $id: http://devicetree.org/schemas/net/mediatek,net.yaml#
(and other complains about wrong clocks).
Fixes: 5f599b3a0b ("arm64: dts: mt7622: add ethernet device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-4-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: cir@10009000: $nodename:0: 'cir@10009000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml#
Fixes: ae457b7679 ("arm64: dts: mt7622: add SoC and peripheral related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-3-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The requested voltage could be lower than the minimum voltage on the
GPU OPP table when the MTK Smart Voltage Scaling (SVS) driver is
enabled, so update the minimum voltage constraint from 600000 uV to
500000 uV as listed on the mt6366 datasheet.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-5-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The requested voltage could be lower than the minimum voltage on the
GPU OPP table when the MTK Smart Voltage Scaling (SVS) driver is
enabled, so removing the definition in mt8183-kukui to use the default
minimum voltage (500000 uV) defined in mt6358.dtsi.
Fixes: 31c6732da9 ("arm64: dts: mediatek: mt8183-kukui: Override vgpu/vsram_gpu constraints")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-4-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Update the minimum voltage from 300000 uV to 400000 uV so it matches
the MT6315 datasheet.
Also update the minimum voltage for Vgpu regulator from 625000 uV to
400000 uV because the requested voltage could be lower than the minimum
voltage on the GPU OPP table when the MTK Smart Voltage Scaling (SVS)
driver is enabled.
Fixes: 260c04d425 ("arm64: dts: mediatek: cherry: Enable MT6315 regulators on SPMI bus")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-3-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Update the minimum voltage from 300000 uV to 400000 uV so it matches
the MT6315 datasheet.
Also update the minimum voltage for Vgpu regulator from 606250 uV to
400000 uV because the requested voltage could be lower than the minimum
voltage on the GPU OPP table when the MTK Smart Voltage Scaling (SVS)
driver is enabled.
Fixes: 3183cb62b0 ("arm64: dts: mediatek: asurada: Add SPMI regulators")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-2-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Describe in each CPU node the regulator supplying it.
Fixes: 260c04d425 ("arm64: dts: mediatek: cherry: Enable MT6315 regulators on SPMI bus")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240110142305.755367-2-nfraprado@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the missing mediatek,gce-client-reg property to the mutex1 node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: 92d2c23dc2 ("arm64: dts: mt8195: add display node for vdosys1")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-4-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the missing mediatek,gce-client-reg property to the mutex node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: b852ee68fd ("arm64: dts: mt8195: Add display node for vdosys0")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-3-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the missing mediatek,gce-client-reg property to the vppsys and
vdosys nodes to allow them to use the GCE. This prevents the "can't
parse gce-client-reg property" error from being printed and should
result in better performance.
Fixes: 6aa5b46d17 ("arm64: dts: mt8195: Add vdosys and vppsys clock nodes")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-2-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the missing mediatek,gce-client-reg property to the mutex node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: b4b75bac95 ("arm64: dts: mt8192: Add display nodes")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-1-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This adds support for the following new machines:
- MT7981B: Xiaomi AX3000T
- MT7986A: Acelink EW-7886CAX
- MT7988A: BananaPi BPI-R4
- MT8186 Chromebooks: Tentacruel, Tentacool, Steelix, Rusty, Magneton
- MT8395/MT8195: Radxa NIO 12L
Also adds more support for the MediaTek MT8186 SoC's Video and JPEG
encoders and for MT7988 clocks, enables wakeup support for the CrOS
EC on SPI in all MediaTek Chromebooks, performs some cleanups and
includes some spare fixes.
-----BEGIN PGP SIGNATURE-----
iJ4EABYKAEYWIQQn3Xxr56ypAcSHzXSaNgTPrZeEeAUCZdNPiigcYW5nZWxvZ2lv
YWNjaGluby5kZWxyZWdub0Bjb2xsYWJvcmEuY29tAAoJEJo2BM+tl4R4XOYBAPIL
G/Y4jGNfCPPS4gFPt7y7WKG6nT270msgGFOFELszAP0WSpiOp0rBUS8oXY+NKchd
gxMuvBtfHE05/shSxasKBw==
=VN5r
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Ac61
-----END PGP SIGNATURE-----
Merge tag 'mtk-dts64-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
MediaTek ARM64 DeviceTree updates for v6.9
This adds support for the following new machines:
- MT7981B: Xiaomi AX3000T
- MT7986A: Acelink EW-7886CAX
- MT7988A: BananaPi BPI-R4
- MT8186 Chromebooks: Tentacruel, Tentacool, Steelix, Rusty, Magneton
- MT8395/MT8195: Radxa NIO 12L
Also adds more support for the MediaTek MT8186 SoC's Video and JPEG
encoders and for MT7988 clocks, enables wakeup support for the CrOS
EC on SPI in all MediaTek Chromebooks, performs some cleanups and
includes some spare fixes.
* tag 'mtk-dts64-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux: (51 commits)
arm64: dts: mt8195-cherry-tomato: change watchdog reset boot flow
arm64: dts: mt7986: add port@5 as CPU port
arm64: dts: mt7622: add port@5 as CPU port
arm64: dts: mediatek: Replace deprecated extcon-usb-gpio id-gpio/vbus-gpio properties
arm64: dts: mediatek: replace underscores in node names
arm64: dts: mediatek: mt8186: Add missing xhci clock to usb controllers
arm64: dts: mediatek: mt8186: Add missing clocks to ssusb power domains
arm64: dts: mediatek: mt7622: add missing "device_type" to memory nodes
arm64: dts: mediatek: mt7986: reorder nodes
arm64: dts: mediatek: mt7986: reorder properties
arm64: dts: mediatek: Add Acelink EW-7886CAX
dt-bindings: arm64: dts: mediatek: Add Acelink EW-7886CAX access point
dt-bindings: vendor-prefixes: add acelink
arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board
dt-bindings: arm64: mediatek: Add MT8395 Radxa NIO 12L board compatible
arm64: dts: mediatek: mt8186: Add video decoder device nodes
arm64: dts: mediatek: mt8195: Add MTU3 nodes and correctly describe USB
arm64: dts: mediatek: Add MT8186 Magneton Chromebooks
arm64: dts: mediatek: Add MT8186 Steelix platform based Rusty
arm64: dts: mediatek: Introduce MT8186 Steelix
...
Link: https://lore.kernel.org/r/20240219131230.157792-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Chanho Min <chanho.min@lge.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-3-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The external output reset signal was originally disabled and sent from
firmware. However, an unfixed bug in the firmware on tomato prevents
the signal from being sent, causing the device to fail to boot. To fix
this, enable external output reset signal to allow the device to reboot
normally.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240124-send-upstream-v3-1-5097c9862a73@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On MediaTek MT7986b RFB and MediaTek MT7986a RFB, port 5 of the MT7531
switch is connected to the second MAC of the SoC as a CPU port. Add the
port and set up the second MAC on the bindings.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240219-for-mediatek-v1-2-7078f23eab82@arinc9.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On Banana Pi BPI-R64 and MediaTek MT7622 RFB1 board, port 5 of the MT7531
switch is connected to the second MAC of the SoC as a CPU port. Add the
port and set up the second MAC on the bindings.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240219-for-mediatek-v1-1-7078f23eab82@arinc9.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Use id-gpios and vbus-gpios instead.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240215093214.796821-3-alexander.stein@ew.tq-group.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240213144626.341463-1-krzysztof.kozlowski@linaro.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The mtu3 usb controllers don't list the xhci clock, though they require
it, and thus rely on the bootloader leaving it on in order to work.
When booting with the upstream arm64 defconfig, the usb controllers will
defer probe until modules have loaded since they have an indirect
dependency on CONFIG_MTK_CMDQ, which is configured as a module. However
at the point where modules are loaded, unused clocks are also disabled,
causing the usb controllers to probe without the xhci clock enabled and
fail to probe:
mtu3 11201000.usb: clks of sts1 are not stable!
mtu3 11201000.usb: device enable failed -110
mtu3 11201000.usb: mtu3 hw init failed:-110
mtu3 11201000.usb: failed to initialize gadget
mtu3: probe of 11201000.usb failed with error -110
(and same for the one at 11281000)
Add the missing clock for the usb controllers so that they can
successfully probe without relying on the bootloader state.
Fixes: f6c3e61c54 ("arm64: dts: mediatek: mt8186: Add MTU3 nodes")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240213-mt8186-ssusb-domain-clk-fix-v2-2-1f981d35f3fd@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The ssusb power domains currently don't list any clocks, despite
depending on some, and thus rely on the bootloader leaving the required
clocks on in order to work.
When booting with the upstream arm64 defconfig, the power domain
controller will defer probe until modules have loaded since it has an
indirect dependency on CONFIG_MTK_CMDQ, which is configured as a module.
However at the point where modules are loaded, unused clocks are also
disabled, causing the ssusb domains to fail to be enabled and
consequently the controller to fail probe:
mtk-power-controller 10006000.syscon:power-controller: /soc/syscon@10006000/power-controller/power-domain@4: failed to power on domain: -110
mtk-power-controller: probe of 10006000.syscon:power-controller failed with error -110
Add the missing clocks for the ssusb power domains so that they can
successfully probe without relying on the bootloader state.
Fixes: d9e43c1e7a ("arm64: dts: mt8186: Add power domains controller")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240213-mt8186-ssusb-domain-clk-fix-v2-1-1f981d35f3fd@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This fixes:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: /: memory@40000000: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/memory.yaml#
arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dtb: /: memory@40000000: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/memory.yaml#
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240122132357.31264-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Use order described as preferred in DTS Coding Style:
1. Sort bus nodes by unit address
2. Use alpha-numerical order for the rest
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240212121620.15035-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg" and "ranges" properties. In two nodes also move
vendor-prefixed props down.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240212121620.15035-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231207080512.3688-3-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The MT8195 SoC has four USB controllers: only one is a direct path to
a XHCI controller, while the other three (0, 2 and 3) are behind the
MTU3 DRD controller instead!
Add the missing MTU3 nodes, default disabled, for controllers 0, 2 and
3 and move the related XHCI nodes to be children of their MTU3 DRD to
correctly describe the SoC.
In order to retain USB functionality on all of the MT8195 and MT8395
boards, also move the vusb33 supply and enable the relevant MTU3 nodes
with special attention to the MT8195 Cherry Chromebook, where it was
necessary to set the dr_mode of all MTU3 controllers to host to avoid
interfering with the EC performing DRD on its own.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240115084336.938426-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add entries for the MT8186 based Chromebooks, also collectively known
as the Lenovo IdeaPad Slim 3 Chromebook (14M868). It is also based on
the "Steelix" design. Being a laptop instead of a convertible device,
there is no stylus, which is similar to Rusty. However Magneton does
not have ports on the right side of the device.
Three variants are listed separately. These use different touchscreen
controllers, or lack a touchscreen altogether.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240126083802.2728610-10-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT8186 Rusty, otherwise known as the Lenovo 100e Chromebook Gen 4, is an
MT8186 based laptop. It is based on the "Steelix" design. Being a laptop
instead of a convertible device, there is no touchscreen or stylus.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240126083802.2728610-9-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The MT8186 Steelix, also known as the Lenovo 300e Yoga Chromebook Gen 4,
is a convertible device based on a common design of the same name. The
device comes in different variants. Of them, whether a world facing
camera is integrated is the only differentiating factor between the
two device trees added. The different SKU IDs describe this alone.
The other device difference is the trackpad component used. This is
simply handled by having both possible components described in the
device tree, and letting the implementation figure out which one is
actually available. The system bootloader / firmware does not
differentiate this in that they share the same SKU IDs.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240126083802.2728610-8-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tentacruel and Tentacool are MT8186 based Chromebooks based on the
Krabby design.
Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
convertible device with touchscreen and stylus.
Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
device. It does not have a touchscreen or stylus.
The two devices both have two variants. The difference is a second
source trackpad controller that shares the same address as the original,
but is incompatible.
The extra SKU IDs for the Tentacruel devices map to different sensor
components attached to the Embedded Controller. These are not visible
to the main processor.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240126083802.2728610-7-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add JPEG encoder node.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Max Staudt <mstaudt@chromium.org>
Tested-by: Max Staudt <mstaudt@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
[eugen.hristev@collabora.com: minor cleanup]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240127084258.68302-2-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add video encoder node.
Signed-off-by: Kyrie Wu <kyrie.wu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
[eugen.hristev@collabora.com: minor cleanup]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231228113245.174706-7-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The larb clock is in fact a subsys clock, so it must be prefixed by
'subsys-' to be correctly identified in the driver.
Fixes: d9e43c1e7a ("arm64: dts: mt8186: Add power domains controller")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231228113245.174706-6-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Clock name should be `venc_sel` as per binding.
Fix the warning message :
arch/arm64/boot/dts/mediatek/mt8192-asurada-hayato-r1.dtb: vcodec@17020000: clock-names:0: 'venc_sel' was expected
from schema $id: http://devicetree.org/schemas/media/mediatek,vcodec-encoder.yaml#
Fixes: aa8f3711fc ("arm64: dts: mt8192: Add H264 venc device node")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231228113245.174706-4-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add efuse nodes for socinfo retrieval for MT8173, MT8183, MT8186,
MT8192 and MT8195.
Signed-off-by: William-tw Lin <william-tw.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231222080739.21706-2-william-tw.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240102140734.v4.12.Iee33a7f1f991408cef372744199026f936bf54e2@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240102140734.v4.11.Ibd330d26a00f5e219a7e448452769124833a9762@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240102140734.v4.10.Iba4a8b7e908989e57f7838a80013a4062be5e614@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240102140734.v4.9.Ic09ebe116c18e83cc1161f4bb073fea8043f03f3@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7988A (AKA MediaTek Filogic 880) is a quad-core ARM Cortex-A73
platform designed for Wi-Fi 7 devices (there is no wireless on SoC
though). The first public MT7988A device is Banana Pi BPI-R4.
Many SoC parts remain to be added (they need their own bindings or
depend on missing clocks). Those present block however are correct and
having base .dtsi will help testing & working on missing stuff.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240108085228.4727-3-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7981B (AKA MediaTek Filogic 820) is a dual-core ARM Cortex-A53 SoC.
One of market devices using this SoC is Xiaomi AX3000T.
This is initial contribution with basic SoC support. More hardware block
will get added later. Some will need their bindings (like auxadc).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240111103928.721-3-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The commit adding the ChromeOS EC to the Asurada Devicetree mistakenly
added a base detection node. While tablet mode detection is supported by
CrosEC and used by Hayato, it is done through the cros-ec-keyb driver.
The base detection node, which is handled by the hid-google-hammer
driver, also provides tablet mode detection but by checking base
attachment status on the CrosEC, which is not supported for Asurada.
Hence, remove the unused CrosEC base detection node for Asurada.
Fixes: eb188a2aaa ("arm64: dts: mediatek: asurada: Add ChromeOS EC")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240207-mt8192-asurada-cbas-remove-v1-1-04cb65951975@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT7986's Infrastructure System Configuration Controller includes reset
controller. It can reset blocks as specified in the
include/dt-bindings/reset/mt7986-resets.h . Add #reset-cells so it can
be referenced properly.
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: infracfg@10001000: '#reset-cells' is a required property
from schema $id: http://devicetree.org/schemas/arm/mediatek/mediatek,infracfg.yaml#
Fixes: 1f9986b258 ("arm64: dts: mediatek: add clock support for mt7986a")
Cc: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240101182040.28538-2-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
PWM is not a clock provider and its binding doesn't specify
"#clock-cells" property.
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: pwm@10048000: '#clock-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pwm/mediatek,mt2712-pwm.yaml#
Fixes: eabb04df46 ("arm64: dts: mt7986: add PWM")
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240101182040.28538-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This fixes following validation errors:
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtb: spi_nand@0: $nodename:0: 'spi_nand@0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/spi-nand.yaml#
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dtb: spi_nand@0: $nodename:0: 'spi_nand@0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/spi-nand.yaml#
Fixes: 885e153ed7 ("arm64: dts: mt7986: add spi related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231116130952.5099-2-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This fixes SPI setup and resolves following validation errors:
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtb: spi_nand@0: Unevaluated properties are not allowed ('spi-rx-buswidth', 'spi-tx-buswidth' were unexpected)
from schema $id: http://devicetree.org/schemas/mtd/spi-nand.yaml#
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dtb: spi_nand@0: Unevaluated properties are not allowed ('spi-rx-buswidth', 'spi-tx-buswidth' were unexpected)
from schema $id: http://devicetree.org/schemas/mtd/spi-nand.yaml#
Fixes: 885e153ed7 ("arm64: dts: mt7986: add spi related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231116130952.5099-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
According to the "inside-secure,safexcel-eip97" binding "clock-names" is
required only if there are two clocks specified. If present the first
name must by "core".
Name "infra_eip97_ck" is invalid and was probably just a typo. Drop it.
Fixes: ecc5287cfe ("arm64: dts: mt7986: add crypto related device nodes")
Cc: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231116132411.7665-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
This fixes typo and resolves following validation error:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: pwm-fan: pwms: [[54, 0, 10000], [0]] is too long
from schema $id: http://devicetree.org/schemas/hwmon/pwm-fan.yaml#
Fixes: c26f779a22 ("arm64: dts: mt7986: add pwm-fan and cooling-maps to BPI-R3 dts")
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231116130816.4932-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The cbas node is used to describe base detection functionality in the
ChromeOS EC, which is used for units that have a detachable keyboard and
thus rely on this functionality to switch between tablet and laptop
mode.
Despite the original commit having added the cbas node to the
mt8183-kukui.dtsi, not all machines that include it are detachables. In
fact all machines that include from mt8183-kukui-jacuzzi.dtsi are either
clamshells (ie normal laptops) or convertibles, meaning the keyboard can
be flipped but not detached. The detection for the keyboard getting
flipped is handled by the driver bound to the keyboard-controller node
in the EC.
Move the base detection node from the base kukui dtsi to the dtsis where
all machines are detachables, and thus actually make use of the node.
Fixes: 4fa8492d1e ("arm64: dts: mt8183: add cbas node under cros_ec")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240116-mt8183-kukui-cbas-remove-v3-1-055e21406e86@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Since commit 26c9d152eb ("dt-bindings: tpm: Consolidate TCG TIS
bindings"), several issues are reported by "make dtbs_check" for arm64
devicetrees:
The compatible property needs to contain the chip's name in addition to
the generic "tcg,tpm_tis-spi" and the nodename needs to be "tpm@0"
rather than "cr50@0":
tpm@1: compatible: ['tcg,tpm_tis-spi'] is too short
from schema $id: http://devicetree.org/schemas/tpm/tcg,tpm_tis-spi.yaml#
cr50@0: $nodename:0: 'cr50@0' does not match '^tpm(@[0-9a-f]+)?$'
from schema $id: http://devicetree.org/schemas/tpm/google,cr50.yaml#
Fix these schema violations.
phyGATE-Tauri uses an Infineon SLB9670:
https://lore.kernel.org/all/ab45c82485fa272f74adf560cbb58ee60cc42689.camel@phytec.de/
Gateworks Venice uses an Atmel ATTPM20P:
https://trac.gateworks.com/wiki/tpm
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
Add the quirk property "rx-fifo-depth" to work around Gen1 isoc-in
transfer issue which send out unexpected ACK even after device
already finished the burst transfer with a short patcket, specially
for a 4K camera device.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the MediaTek SVS node: this will lower the voltage of various
components of the SoC based on chip quality (read from fuses) in
order to save power and generate less heat.
Also, reduce the LVTS_AP iospace to 0xc00, because that's exactly
where SVS starts.
- LVTS_AP start: 0x1100b000 length: 0xc00
- SVS start: 0x1100bc00 length: 0x400
Link: https://lore.kernel.org/r/20231121125044.78642-21-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The SVS iospace starts at 0x1100bc00 and not at 0x1100b000 as the
latter is the thermal sensor iospace instead.
Change the iospaces for both as following:
- Thermal: 0x1100b000, length 0xc00
- SVS: 0x1100bc00, length 0x400
Please note that while this would be a breaking change for SVS (but
not for thermal sensors), it doesn't matter because the svs driver
never worked anyway because of the missing trips in tzts2, causing
that thermal zone to never actually register, hence the SVS driver
to fail probing anyway.
Link: https://lore.kernel.org/r/20231121125044.78642-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fix warnings reported by dtbs_check :
arch/arm64/boot/dts/mediatek/mt8186.dtsi:1163.35-1168.5: Warning (simple_bus_reg):
/soc/mailbox@10686000: simple-bus unit address format error, expected "10686100"
arch/arm64/boot/dts/mediatek/mt8186.dtsi:1170.35-1175.5: Warning (simple_bus_reg):
/soc/mailbox@10687000: simple-bus unit address format error, expected "10687100"
by having the right bus address as node name.
Fixes: 379cf0e639 ("arm64: dts: mediatek: mt8186: Add ADSP mailbox nodes")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Link: https://lore.kernel.org/r/20231204135533.21327-1-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The alias prefix for ovl_2l (2 layer overlay) is "ovl-2l", not "ovl_2l".
Fix this.
Fixes: 7e07d3322d ("arm64: dts: mediatek: mt8186: Add display nodes")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20231130074032.913511-4-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Whether a regulator under the MT6358 PMIC is a fixed regulator or not is
derived from the node name. Compatible string properties are not used.
This causes validation errors after the regulator binding is converted
to DT schema.
Drop the bogus "regulator-fixed" compatible properties from the PMIC's
regulator sub-nodes.
Fixes: 9f88722216 ("arm64: dts: mt6358: add PMIC MT6358 related nodes")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20231130074032.913511-3-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The panel_flag property was used in ChromeOS's downstream kernel. It was
used to signal whether the downstream device was a fixed panel or
a connector for an external display.
This property was dropped in favor of standard OF graph descrptions of
downstream display panels and bridges.
Drop the property from the device tree file.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20231130074032.913511-2-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT8188 is a SoC based on 64bit ARMv8 architecture. It contains 6 CA55
and 2 CA78 cores. MT8188 share many HW IP with MT65xx series.
We add basic chip support for MediaTek MT8188 on evaluation board.
Signed-off-by: jason-ch chen <Jason-ch.Chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231023083839.24453-5-jason-ch.chen@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the two DSI controller node and the associated DPHY nodes.
Individual boards have to enable them in the board device tree.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The ldo_vcn33_bt and ldo_vcn33_wifi regulators are actually the same
regulator, having the same voltage setting and output pin. There are
simply two enable bits that are ORed together to enable the regulator.
Having two regulators representing the same output pin is misleading
from a design matching standpoint, and also error-prone in driver
implementations.
Now that the bindings have these two merged, merge them in the device
tree as well. Neither vcn33 regulators are referenced in upstream
device trees. As far as hardware designs go, none of the Chromebooks
using MT8183 w/ MT6358 use this output.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add device nodes for Media Data Path 3 (MDP3) modules.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
DMA-related nodes have their own standardized naming. Therefore,
the MT8195 VDOSYS RDMA has been unified and corrected.
Additionally, these modifications will facilitate the further
integration of bindings.
Fixes: 92d2c23dc2 ("arm64: dts: mt8195: add display node for vdosys1")
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In order to generalize the node names, the DMA-related nodes
corresponding to MT8183 MDP3 need to be corrected.
Fixes: 60a2fb8d20 ("arm64: dts: mt8183: add MediaTek MDP3 nodes")
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a phandle to the MT8195_POWER_DOMAIN_MFG1 power domain and
assign the GPU SRAM (vsram_others) supply to that in mt8195-cherry:
this allows to keep the sram powered up while the GPU is used.
This means that it's now possible to remove the regulator-always-on
property from the mt6359_vsram_others_ldo_reg vreg, so that it will
be switched on and off during suspend.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MFG0 is the main power domain for the GPU and its surrounding glue
logic, and has a specific power rail.
Add its power supply on Cherry platforms and remove the now useless
(and wrong) regulator-always-on property from the vbuck1 regulator.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
pico is also known as Acer Chromebook Spin 311.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[Angelo: Fixed blank lines at the end for pico.dts]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
makomo is also known as Lenovo 100e Chromebook 2nd Gen MTK 2.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
katsu is also known as ASUS Chromebook Detachable CZ1.
Let katsu and kakadu set its own touchscreen and panel compatible. Remove
these setting from the common dtsi for readability.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT6358 is a PMIC that is typically used on MT8183 boards, and it has
its own dtsi file, declaring interrupts-extended on its node.
The interrupt pin of that PMIC is connected to a SoC GPIO and that
is therefore not only SoC-specific, but board-specific: this means
that the interrupt-extended property does not belong to the PMIC
dtsi file, but to board files using that PMIC.
For correctness, transfer the interrupts-extended property from the
PMIC-specific mt6358.dtsi to board files.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
As already done for MT8173 and MT8183 devicetrees, change all instances
of interrupt-parent + interrupts to one line as interrupts-extended
where possible across all remaining device trees to both simplify and
reduce code size.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Change all instances of interrupt-parent + interrupts to one line
as interrupts-extended where possible across all MT8173 DTs to both
simplify and reduce code size.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Change all instances of interrupt-parent + interrupts to one line
as interrupts-extended where possible across all MT8183 DTs to both
simplify and reduce code size.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add thermal nodes and thermal zones for the mt8192.
The mt8192 SoC has several hotspots around the CPUs.
Specify the targeted temperature threshold to apply the mitigation
and define the associated cooling devices.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[bero@baylibre.com: cosmetic changes, reduce lvts_ap size]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add node for the hardware decoder present on the MT8183 SoC.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Qianqian Yan <qianqian.yan@mediatek.com>
Signed-off-by: Frederic Chen <frederic.chen@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230630151436.155586-8-nfraprado@collabora.com
Remove the VDEC_SYS register space from the decoder, so that the node
address becomes that of VDEC_MISC, solving the long-standing conflicting
addresses between this node and the vdecsys clock-controller node:
arch/arm64/boot/dts/mediatek/mt8173.dtsi:1365.38-1369.5: Warning (unique_unit_address_if_enabled): /soc/clock-controller@16000000: duplicate unit-address (also used in node /soc/vcodec@16000000)
The driver makes use of this register space, however, so also add a
phandle to the VDEC_SYS syscon to maintain functionality.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230630151436.155586-7-nfraprado@collabora.com
This platform has three auxiliary NTC thermistors, connected to the
SoC's ADC pins. Enable the auxadc in order to be able to read the
ADC values, add a generic-adc-thermal LUT for each and finally assign
them to the SoC's thermal zones.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230424112523.1436926-2-angelogioacchino.delregno@collabora.com
dtbs_check throws a warning at the dsi node:
Warning (avoid_unnecessary_addr_size): /soc/dsi@14014000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Other DTS have a panel child node with a reg, so the parent dtsi
must have the address-cells and size-cells, however this specific DT
has the panel removed, but not the cells, hence the warning above.
If panel is deleted then the cells must also be deleted since they are
tied together, as the child node in this DT does not have a reg.
Cc: stable@vger.kernel.org
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230814071053.5459-1-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
dtbs_check throws a warning at the memory node:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
fix by adding the address into the node name.
Cc: stable@vger.kernel.org
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230814065042.4973-1-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Clocks for each power domain are split into big categories: pd clocks
and subsys clocks.
According to the binding, all clocks which have a dash '-' in their name
are treated as subsys clocks, and must be placed at the end of the list.
The other clocks which are pd clocks must come first.
Fixed the naming and the placing of all clocks in the power domains.
For the avoidance of doubt, prefixed all subsys clocks with the 'subsys'
prefix. The binding does not enforce strict clock names, the driver
uses them in bulk, only making a difference for pd clocks vs subsys clocks.
The above problem appears to be trivial, however, it leads to incorrect
power up and power down sequence of the power domains, because some
clocks will be mistakenly taken for subsys clocks and viceversa.
One consequence is the fact that if the DIS power domain goes power down
and power back up during the boot process, when it comes back up, there
are still transactions left on the bus which makes the display inoperable.
Some of the clocks for the DIS power domain were wrongly using '_' instead
of '-', which again made these clocks being treated as pd clocks instead of
subsys clocks.
Cc: stable@vger.kernel.org
Fixes: d9e43c1e7a ("arm64: dts: mt8186: Add power domains controller")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231005103041.352478-1-eugen.hristev@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
MT8186's GPU speedbin value must be interpreted, or the value will not
be meaningful.
Use the correct "gpu-speedbin" nvmem cell name for the GPU speedbin to
allow triggering the cell info fixup handler, hence feeding the right
speedbin number to the users.
Cc: stable@vger.kernel.org
Fixes: 263d2fd02a ("arm64: dts: mediatek: mt8186: Add GPU speed bin NVMEM cells")
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20231005151150.355536-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add Critical and hot trips for emergency system shutdown and limiting
system load.
Change passive trip to active to make sure fan is activated on the
lowest trip.
Cc: stable@vger.kernel.org
Fixes: 1f5be05132 ("arm64: dts: mt7986: add thermal-zones")
Fixes: c26f779a22 ("arm64: dts: mt7986: add pwm-fan and cooling-maps to BPI-R3 dts")
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231025170832.78727-4-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
All SFP power supplies are connected to the system VDD33 which is 3v3/8A.
Set 3A per SFP slot to allow SFPs work which need more power than the
default 1W.
Cc: stable@vger.kernel.org
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231025170832.78727-3-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Replace underscores with hyphens in pinctrl node names both for consistency
and to adhere to the bindings.
Cc: stable@vger.kernel.org
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Fixes: 1652dbf736 ("arm64: dts: mt8183: add scp node")
Fixes: 27eaf34df3 ("arm64: dts: mt8183: config dsi node")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231026191343.3345279-2-hsinyi@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The NTC is defined as ntc@0 but it doesn't need any address at all.
Fix the unit_address_vs_reg warning by dropping the unit address: since
the node name has to be generic also fully rename it from ntc@0 to
thermal-sensor.
Cc: stable@vger.kernel.org
Fixes: ff9ea5c622 ("arm64: dts: mediatek: mt8183-evb: Add node for thermistor")
Link: https://lore.kernel.org/r/20231025093816.44327-7-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Before suspending the LARBs we're making sure that any operation is
done: this never happens because we are unexpectedly unclocking the
LARB20 before executing the suspend handler for the MediaTek Smart
Multimedia Interface (SMI) and the cause of this is incorrect clocks
on this LARB.
Fix this issue by changing the Local Arbiter 20 (used by the video
encoder secondary core) apb clock to CLK_VENC_CORE1_VENC;
furthermore, in order to make sure that both the PM resume and video
encoder operation is stable, add the CLK_VENC(_CORE1)_LARB clock to
the VENC (main core) and VENC_CORE1 power domains, as this IP cannot
communicate with the rest of the system (the AP) without local
arbiter clocks being operational.
Cc: stable@vger.kernel.org
Fixes: 3b5838d1d8 ("arm64: dts: mt8195: Add iommu and smi nodes")
Fixes: 2b515194bf ("arm64: dts: mt8195: Add power domains controller")
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230706095841.109315-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers.
-----BEGIN PGP SIGNATURE-----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=E1ta
-----END PGP SIGNATURE-----
Merge tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers"
* tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: st: Fix sometimes uninitialized ret in st_rproc_probe()
remoteproc: st: Use device_get_match_data()
remoteproc: zynqmp: Change tcm address translation method
remoteproc: mediatek: Refactor single core check and fix retrocompatibility
remoteproc: qcom: q6v5-mss: Remove PNoC clock from 8996 MSS
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Remove PNoC clock
dt-bindings: remoteproc: qcom,adsp: Remove AGGRE2 clock
remoteproc: qcom: pas: Add SM6375 MPSS
remoteproc: qcom: pas: Add SM6375 ADSP & CDSP
dt-bindings: remoteproc: qcom,sm6375-pas: Document remoteprocs
dt-bindings: remoteproc: pru: Add Interrupt property
remoteproc: qcom: pas: Add sc7180 adsp
dt-bindings: remoteproc: qcom: sc7180-pas: Add ADSP compatible
arm64: dts: mediatek: Update the node name of SCP rpmsg subnode
remoteproc: zynqmp: fix TCM carveouts in lockstep mode
remoteproc: mediatek: Refine ipi handler error message
remoteproc: mediatek: Report watchdog crash to all cores
remoteproc: mediatek: Handle MT8195 SCP core 1 watchdog timeout
remoteproc: mediatek: Setup MT8195 SCP core 1 SRAM offset
remoteproc: mediatek: Remove dependency of MT8195 SCP L2TCM power control on dual-core SCP
...
There are a couple new SoCs that are supported for the first time:
- AMD Pensando Elba is a data processing unit based on Cortex-A72
CPU cores
- Sophgo makes RISC-V based chips, and we now support the CV1800B
chip used in the milkv-duo board and the massive sg2042 chip in the
milkv-pioneer, a 64-core developer workstation.
- Qualcomm Snapdragon 720G (sm7125) is a close relative of
Snapdragon 7c and gets added with some Xiaomi phones
- Renesas gains support for the R8A779F4 (R-Car S4-8) automotive
SoC and the RZ/G3S (R9A08G045) embedded SoC.
There are also a bunch of newly supported machines that use
already supported chips. On the 32-bit side, we have:
- USRobotics USR8200 is a NAS/Firewall/router based on the ancient
Intel IXP4xx platform
- A couple of machines based on the NXP i.MX5 and i.MX6 platforms
- One machine each for Allwinner V3s, Aspeed AST2600, Microchip
sama5d29 and ST STM32mp157
The other ones all use arm64 cores on chips from allwinner,
amlogic, freescale, mediatek, qualcomm and rockchip.
-----BEGIN PGP SIGNATURE-----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=NnPm
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There are a couple new SoCs that are supported for the first time:
- AMD Pensando Elba is a data processing unit based on Cortex-A72 CPU
cores
- Sophgo makes RISC-V based chips, and we now support the CV1800B
chip used in the milkv-duo board and the massive sg2042 chip in the
milkv-pioneer, a 64-core developer workstation.
- Qualcomm Snapdragon 720G (sm7125) is a close relative of Snapdragon
7c and gets added with some Xiaomi phones
- Renesas gains support for the R8A779F4 (R-Car S4-8) automotive SoC
and the RZ/G3S (R9A08G045) embedded SoC.
There are also a bunch of newly supported machines that use already
supported chips. On the 32-bit side, we have:
- USRobotics USR8200 is a NAS/Firewall/router based on the ancient
Intel IXP4xx platform
- A couple of machines based on the NXP i.MX5 and i.MX6 platforms
- One machine each for Allwinner V3s, Aspeed AST2600, Microchip
sama5d29 and ST STM32mp157
The other ones all use arm64 cores on chips from allwinner, amlogic,
freescale, mediatek, qualcomm and rockchip"
* tag 'soc-dt-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (641 commits)
ARM: dts: BCM5301X: Set switch ports for Linksys EA9200
ARM: dts: BCM5301X: Set fixed-link for extra Netgear R8000 CPU ports
ARM: dts: BCM5301X: Explicitly disable unused switch CPU ports
ARM: dts: BCM5301X: Relicense Vivek's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense Felix's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Set MAC address for Asus RT-AC87U
arm64: dts: socionext: add missing cache properties
riscv: dts: thead: convert isa detection to new properties
arm64: dts: Update cache properties for socionext
arm64: dts: ti: k3-am654-idk: Add ICSSG Ethernet ports
arm64: dts: ti: k3-am654-icssg2: add ICSSG2 Ethernet support
arm64: dts: ti: k3-am65-main: Add ICSSG IEP nodes
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: rockchip: Add Turing RK1 SoM support
dt-bindings: arm: rockchip: Add Turing RK1
dt-bindings: vendor-prefixes: add turing
arm64: dts: rockchip: Add DFI to rk3588s
arm64: dts: rockchip: Add DFI to rk356x
arm64: dts: rockchip: Always enable DFI on rk3399
...
- Add support for SMI/IOMMU/LARBs, power domains and multimedia
related subsystems for the MT8365 SoC
- Add support for MediaTek Genio 1200 IoT evaluation board
- Add support for newer revisions of MT8192 Chromebooks
- Add support for internal eDP display on MT8195 Cherry Chromebooks
- Add display and display backlight support for the Helio X10 SoC and
for the Sony Xperia M5 smartphone
-----BEGIN PGP SIGNATURE-----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=BJIG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Bh9O
-----END PGP SIGNATURE-----
Merge tag 'v6.6-next-dts64.3' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into soc/dt
MediaTek ARM64 DTS updates for v6.7
- Add support for SMI/IOMMU/LARBs, power domains and multimedia
related subsystems for the MT8365 SoC
- Add support for MediaTek Genio 1200 IoT evaluation board
- Add support for newer revisions of MT8192 Chromebooks
- Add support for internal eDP display on MT8195 Cherry Chromebooks
- Add display and display backlight support for the Helio X10 SoC and
for the Sony Xperia M5 smartphone
* tag 'v6.6-next-dts64.3' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (21 commits)
arm64: dts: mediatek: cherry: Configure eDP and internal display
arm64: dts: mediatek: mt6795-xperia-m5: Add DSI Display and its vregs
arm64: dts: mediatek: mt6795-xperia-m5: Add display backlight support
arm64: dts: mediatek: mt6795: Add support for display blocks and DPI/DSI
arm64: dts: mediatek: Add spherion-rev4
arm64: dts: mediatek: Add hayato-rev5-sku2
arm64: dts: mediatek: Remove asurada-audio dtsi files
dt-bindings: arm64: dts: mediatek: Add rev4 of spherion
dt-bindings: arm64: dts: mediatek: Add rev5-sku2 of hayato
arm64: dts: mediatek: add iommu support for mt8365 SoC
arm64: dts: mediatek: add larb support for mt8365 SoC
arm64: dts: mediatek: add smi support for mt8365 SoC
arm64: dts: mediatek: add power domain support for mt8365 SoC
arm64: dts: mediatek: add apu support for mt8365 SoC
arm64: dts: mediatek: add camsys support for mt8365 SoC
arm64: dts: mediatek: add mmsys support for mt8365 SoC
arm64: dts: mediatek: mt8183-kukui: Add PMIC regulator supplies
arm64: dts: mediatek: add device-tree for Genio 1200 EVK board
dt-bindings: arm64: mediatek: add mt8395-evk board
dt-bindings: power: Add MT8365 power domains
...
Link: https://lore.kernel.org/r/298f159c-f80d-3ba8-fde9-b11b59e5a58e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the required nodes to enable the DisplayPort interface, connected
to the Embedded DisplayPort port, where we have an internal display.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230816190427.2137768-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the DSI display found on the Sony Xperia M5, including
the necessary regulators configuration for it.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the relevant nodes for display backlight on Sony Xperia M5: this
needs both the SoC PWM IP and MT6332 PMIC LED strings.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce all nodes for all of the display blocks in the MediaTek Helio
X10 MT6795 SoC, including the DSI PHY and DSI/DPI interfaces: those are
left disabled as usage is board specific.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a devicetree for rev4 of Spherion. It uses the rt5682s audio codec
instead of the rt5682 used in the previous revision.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-6-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a devicetree for rev5-sku2 of Hayato. It uses the rt5682s audio
codec instead of the rt5682 used in the previous revision.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-5-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There aren't enough users of the common asurada-audio dtsi files to
justify having them. It is simpler to just have the audio nodes directly
on the board files.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-4-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add iommu support in the SoC DTS using the 4 local arbiters (LARBs)
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-7-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Local arbiter (LARB) is a component of Smart Multimedia Interface (SMI),
used to help the memory management (IOMMU).
This patch add 4 LARBs and 2 clocks for the larb1 and larb3 support.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-6-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Smart Multimedia Interface (SMI) local arbiter does the arbitration for
memory requests from multi-media engines. Add SMI in the MT8365 DTS will
allow to add local ARBiter (LARB), use by IOMMU.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-5-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
AI Processor Unit System (APUSYS) is a highly efficient computing unit
system which is most suitable for AI/CV algorithms. It includes one
programmable AI processor (Cadence VP6) for both AI and CV algorithms,
and an eDMA engine for data movement between external DRAM and VP6
internal memory.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-3-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Camera System (CamSys) incorporates an enhanced feature based image
signal processor to connect a variety of image sensor components. This
processor consists of timing generated unit (TG), lens/sensor
compensation unit and image process unit.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-2-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Multimedia subsystem (MMsys) contains multimedia controller, Multimedia
Data Path v2.0 (MDP 2.0) and Display (DISP). The multimedia controller
includes bus fabric control, Smart Memory Interface (SMI) control,
memory access second-level arbiter, and multimedia configuration. It
plays the key role in handling different handshakings between infra
subsystem, video subsystem, image subsystem and G3D subsystem.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-1-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The PMIC regulator node is missing regulator supplies. Now that the
binding supports them, add all the power rail supplies. Most of them
are fed from a system-wide semi-regulated power rail. A couple LDOs
are fed from the PMIC's own buck regulator outputs.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230928085537.3246669-13-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add basic device-tree for the Genio 1200-EVK board. This board
is made by MediaTek and has a MT8395 SoC (MT8195 family),
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 2 USB Type-A connector with a USB hub
* 1 micro-USB port for gadget or OTG support
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 micro SD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays, 1 of the DSI panel is installed
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
* 1 Touch Panel (installed DSI display)
* 1 M.2 slot for 5G dongle
This commit adds basic support in order to be able to boot.
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230914055145.16801-2-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for
the mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own
for the past few years.
Generic RISC-V kernels are now marked as incompatible with the
RZ/Five platform that requires custom hacks both for managing
its DMA bounce buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver
to prevent a use-after-free bug.
-----BEGIN PGP SIGNATURE-----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=Ukoh
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for the
mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own for
the past few years.
Generic RISC-V kernels are now marked as incompatible with the RZ/Five
platform that requires custom hacks both for managing its DMA bounce
buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver to prevent
a use-after-free bug"
* tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
IXP4xx MAINTAINERS entries
arm64: dts: mediatek: mt8195: Set DSU PMU status to fail
arm64: dts: mediatek: fix t-phy unit name
arm64: dts: mediatek: mt8195-demo: update and reorder reserved memory regions
arm64: dts: mediatek: mt8195-demo: fix the memory size to 8GB
MAINTAINERS: Add Angelo as MediaTek SoC co-maintainer
soc: renesas: Make ARCH_R9A07G043 (riscv version) depend on NONPORTABLE
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtbs_check throws a warning at t-phy nodes:
Warning (unit_address_vs_reg): /t-phy@1a243000: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /soc/t-phy@11c00000: node has a unit name, but no reg or ranges property
The ranges is empty thus removing the `@1a243000`, `@11c00000` from
the node name.
Fixes: 6029cae696 ("arm64: dts: mediatek: mt7622: harmonize node names and compatibles")
Fixes: 918aed7abd ("arm64: dts: mt7986: add pcie related device nodes")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230814093931.9298-2-eugen.hristev@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-4-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The dts file of the MediaTek MT8195 demo board has been updated to include
new reserved memory regions.
These reserved memory regions are:
- SCP
- VPU,
- Sound DMA
- APU.
These regions are defined with the "shared-dma-pool" compatible property.
In addition, the existing reserved memory regions have been reordered by
their addresses to improve readability and maintainability of the DTS
file.
Cc: stable@vger.kernel.org # 6.1, 6.4, 6.5
Fixes: e4a4175201 ("arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230905034511.11232-2-macpaul.lin@mediatek.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-3-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Align the node name with the definition in SCP bindings.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230901080935.14571-3-tinghan.shen@mediatek.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
"mediatek,merge-mute" and "mediatek,merge-fifo-en" properties are defined
and used as boolean properties which in DT have no value.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230830195650.704737-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The defined value for "status" is "disabled", not "disable".
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230804225813.12493-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bootrom burned into the MT7986 SoC will try multiple locations on
the SPI-NAND flash to load bl2 in case the bl2 image located at the the
previously attempted offset is corrupt.
Use 0x100000 instead of 0x80000 as partition size for bl2 on SPI-NAND,
allowing for up to four redundant copies of bl2 (typically sized a
bit less than 0x40000).
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZH9UGF99RgzrHZ88@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the GPU's OPP table. This is from the downstream ChromeOS kernel,
adapted to the new upstream opp-supported-hw binning format. Also add
dynamic-power-coefficient for the GPU.
Also add label for mfg1 power domain. This is to be used at the board
level to add a regulator supply for the power domain.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-5-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On the MT8186, the chip is binned for different GPU voltages at the
highest OPPs. The binning value is stored in the efuse.
Add the NVMEM cell, and tie it to the GPU.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-4-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds clocks, dynamic power coefficients, and OPP tables for the CPU
cores, so that everything required at the SoC level for CPU freqency and
voltage scaling is available.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-3-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a device node for the CCI (cache coherent interconnect) and an OPP
table for it. The OPP table was taken from the downstream ChromeOS
kernel.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-2-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pwm-fan and cooling-maps to BananaPi-R3 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal-zones to mt7986 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-4-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal related nodes to mt7986 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A76) cluster at a maximum of 2200MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculated the mean result for each cluster
4. Calculated DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scaled results to 1024:
result_c0 = dmips_mhz_c0 / dmips_mhz_c1 * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 12016411 Dhry/s
Cluster 1 (BIG): 31702034 Dhry/s
The calculated scaled results are:
Cluster 0: 426.953226899238 (rounded to 427)
Cluster 1: 1024
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230602183515.3778780-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In the series "Adjust the dma-ranges for MTK IOMMU", the mtk-iommu
driver was adapted to separate the iova range based on the larb used,
and a dma-ranges property was added to the soc node in the devicetree of
the affected SoCs allowing the whole 16GB iova range to be used. Except
that for mt8192, there was no patch adding dma-ranges.
Add the missing dma-ranges property to the soc node like was done for
mt8195 and mt8186. This fixes the usage of the vcodec, which would
otherwise trigger iommu faults.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601203221.3675915-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add video-codec lat and core nodes for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230303013842.23259-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the cpufreq nodes for MT8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230317061944.15434-1-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Currently a specific panel number is used in the Elm DTSI, which is
corresponded to a 12" panel. However, according to the official Chrome
OS devices document, Elm refers to Acer Chromebook R13, which, as the
name specifies, uses a 13.3" panel, which comes with EDID information.
As the kernel currently prioritizes the hardcoded timing parameters
matched with the panel number compatible, a wrong timing will be applied
to the 13.3" panel on Acer Chromebook R13, which leads to blank display.
Because the Elm DTSI is shared with Hana board, and Hana corresponds to
multiple devices from 11" to 14", a certain panel model number shouldn't
be present, and driving the panel according to its EDID information is
necessary.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230526100801.16310-1-uwu@icenowy.me
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To store uncompressed bl2 more space is required than partition is
actually defined.
There is currently no known usage of this reserved partition.
Openwrt uses same partition layout.
We added same change to u-boot with commit d7bb1099 [1].
[1] d7bb109900
Cc: stable@vger.kernel.org
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230528113343.7649-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add "regulator-boot-on" to "panel_fixed_3v3" to save time on powering
the regulator during boot. Also add "off-on-delay-us" to the node to
make sure the regulator never violates the panel timing requirements.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230417123956.926266-1-treapking@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Leds for Wifi are low-active, so add property to devicetree.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230205174833.107050-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds pwm node to mt7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20230421132047.42166-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The chassis-type string identifies the form-factor of the system:
add this property to all device trees of devices for which the form
factor is known.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230517101108.205654-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As all level 2 and level 3 caches are unified, add required
cache-unified properties to fix warnings like:
mt7622-rfb1.dtb: l2-cache: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230421223157.115367-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8195 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.5.Ia0b6ebbaa351e3cd67e201355b9ae67783c7d718@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8192 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 331fae2fc9 ("arm64: dts: mediatek: Introduce MT8192-based Asurada board family")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.4.Ie7e600278ffbed55a1e5a58178203787b1449b35@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8183 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.3.I525a2ed4260046d43c885ee1275e91707743df1c@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On the Cherry platform, a MT7621 WiFi+Bluetooth combo is connected
over PCI-Express (for WiFi) and USB (for BT): enable the PCIe ports
to enable enumerating this chip.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230424112523.1436926-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Assign aliases for the primary and secondary dp-intf IP to properly
and reliably enable DisplayPort functionality.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230424112523.1436926-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hayato's Realtek WiFi/BT module has it's Bluetooth function wired to
UART1.
Add and enable the relevant device nodes for it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230424100409.2992418-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since commit ba751e28d4 ("net: dsa: mt7530: add interrupt support")
the mt7530 driver can act as an interrupt controller. Wire up irq line
of the MT7531 switch on the BananaPi BPi-R64 board, so the status of
the PHYs of the five 1000Base-T ports doesn't need to be polled any
more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA-DV_OsmFg5egL@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The SPI-NOR node in the device tree of the BananaPi R64 has most likely
been copied from the reference board's device tree even though the R64
comes with an SPI-NAND chip rather than SPI-NOR.
Setup the Serial NAND Flash Interface (SNFI) controller, enable
hardware BCH error detection and correction engine and add the SPI-NAND
chip including basic partitions,
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA96dmaXqTpk8u8@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This smartphone uses the Helio X10 standard MT6331+MT6332 combo PMICs:
include the mt6331 devicetree and add the required interrupt.
Note that despite there being two interrupts, one for MT6331 and one
for MT6332, in configurations using the companion PMIC, the interrupt
of the latter fires for both events on MT6331 and for ones on MT6332,
while the interrupt for the main PMIC fires only for events of the
main PMIC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-25-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6331 is the primary PMIC for the MediaTek Helio X10 MT6795 smartphone
platforms: add a devicetree describing its regulators, Real Time Clock
and PMIC-keys.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-24-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add nodes for the multimedia IOMMU and its LARBs: this includes all but
the MJC LARB, which cannot currently be used and will be added later.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-19-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add AP Domain thermal zones for the mt8195 and
specify the targeted temperature thresholds.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Link: https://lore.kernel.org/r/20230405100907.53740-1-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
