This patch adds support for GSCL power domain to Exynos 5433 SoCs, which
contains following devices: a clock controller, three GSCL video scalers and
their SYSMMUs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add device tree node with S3FWRN5 NFC chip to TM2(e) boards. The chip is
connected through HS-I2C bus #4.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
[mszyprow: rebased onto v4.15-rc1, moved node to exynos5433-tm2-common.dtsi,
rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for ARM Performance Monitoring Units available in
Cortex-A53 and Cortex-A57 CPU cores for Exynos5433 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since commit 9840354ff4 ("usb: dwc3: Add dual-role support") dwc3
node requires extcon property to be initialized as OTG mode and it
supports dual-role mode operation.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 has two usb 3.0 controllers: usbhost and usbdrd. usbhost
is host-only controller whereas usbdrd supports both peripheral and
host mode. "drd" means dual-role device, so usbhost cannot be labeled
with the name containing "drd". However, the label usbdrd_dwc3_0 was
used for usbhost's dwc3 node. It seems it obviously fault because TM2
and TM2E doesn't use usbhost but dr_mode property is assigned to it.
This patch assigns the proper label for two dwc3 nodes.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The OF graph is not needed because the panel is a child of dsi. Remove
the ports node in DSI node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The decon uses HW-TRIGGER, so TE interrupt is not necessary.
Therefore, remove the te-gpios property in the TM2 dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the panel device tree node for s6e3hf2 display
controller to TM2e dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the burst and esc clock frequency properties to the parent (DSI node).
Currently the clock is parsed from the port node, while it should be
taken from the dsi node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
TM2 and TM2E devices are provided with a ST-Microelectronics
Finger Tip S device with small differences:
- screen size
- TM2E uses the stmfts also as a touchkey for "back" and "menu"
In this commit the initial value of the interrupt line is set to
EXYNOS_PIN_PULL_UP as the interrupt is triggered when the line
goes down.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the device tree node for the ir-spi driver which enables the
IR LED for remote controlling.
This patch sets first the GPR3[3] gpio line as a regulator-fixed
for enabling an external regulator which powers the IR LED.
Removes also the default assignment of GPG3[7] related to the
MOSI line of the SPI3 bus.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Adding fixed voltage regulators for Vbus and Vbus-boost required
by USB 3.0 DRD controller on Exynos7-espresso board.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add USB 3.0 DRD controller device node, with its clock
and phy information to enable the same on Exynos7.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 LPASS module requires some clocks for proper operation with
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO7 regulator beside DSI and HDMI provides power for core blocks in Exynos
5433 SoC. Disabling it causes serious current leak - about 200mA.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Ultra HD modes requires clock ticking at increased rate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As per Exynos7 datasheet FSYS1 pinctrl block does not support drive
strength value of 0x3. This patch fixes this and update the correct
drive strength for sd0_xxx pin definitions.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Common definition for I2S, PMC, SPDIF buses should not define any pull
control for the individual pins. Correct this by changing samsung,pin-pud
property to EXYNOS_PIN_PULL_NONE like it is defined for other Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "samsung,exynos5433-mipi-video-phy" and "samsung,exynos5250-dwusb3"
DT bindings don't specify a reg property for these nodes, so having a
unit name leads to the following DTC warnings:
Node /soc/video-phy@105c0710 has a unit name, but no reg property
Node /soc/usb@15400000 has a unit name, but no reg property
Node /soc/usb@15a00000 has a unit name, but no reg property
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
HDMI converts RGB/I80 signal from DECON_TV to HDMI/TMDS video stream.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DECON_TV is 2nd display controller on Exynos5433, used in HDMI path
or 2nd DSI path.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Address should not contain 0x prefix.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tree-wide replacement was done by commit 2ef7d5f342 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78f0 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").
Here, some new users have appeared for Linux v4.10-rc1. Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch fixes wrong values assigned to ldo23 and ldo25 on both TM2 and TM2E.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use the macros defined in include/dt-bindings/pinctrl/samsung.h
instead of hardcoded values.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the bus Device-tree nodes for INT (Internal) block
and enables the bus frequency scaling.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the AMBA AXI bus nodes using VDD_INT for Exynos5433 SoC.
Following list specify the detailed correlation between sub-block and clock:
- CLK_ACLK_G2D_{400|266} : Bus clock for G2D (2D graphic engine)
- CLK_ACLK_MSCL_400 : Bus clock for MSCL (Memory to memory Scaler)
- CLK_ACLK_GSCL_333 : Bus clock for GSCL (General Scaler)
- CLK_SCLK_JPEG_MSCL : Bus clock for JPEG
- CLK_ACLK_MFC_400 : Bus clock for MFC (Multi Format Codec)
- CLK_ACLK_HEVC_400 : Bus clock for HEVC (High Efficient Video Codec)
- CLK_ACLK_BUS0_400 : NoC's (Network On Chip) bus clock for PERIC/PERIS/FSYS/MSCL
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds PPMU (Platform Performance Monitoring Unit) Device-tree node
to measure the utilization of each IP in Exynos SoC.
- PPMU_D{0|1}_CPU are used to measure the utilization of MIF (Memory Interface)
block with VDD_MIF power source.
- PPMU_D{0|1}_GENERAL are used to measure the utilization of INT(Internal)
block with VDD_INT power source.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/AE/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree arm64 second update for v4.10" from Krzysztof Kozłowski:
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
* tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: dts: exynos: TM2 - add support for MFC video codec device
arm64: dts: exynos: TM2 - add support for JPEG codec device
arm64: dts: exynos: TM2 - add support for GScaler devices
arm64: dts: exynos: TM2 - remove unused UART3 and set clocks directly on CMU
arm64: dts: exynos: Assign parent clock of the clkout clock for TM2 board
arm64: dts: exynos: Move FSYS CMU configuration from Exynos5433 dtsi to TM2 dts
arm64: dts: exynos: Add missing parent clocks to audio block in Exynos5433 SoC
arm64: dts: exynos: Fix FSYS CMU parent clocks in Exynos5433 SoC
arm64: dts: exynos: Fix IRQ type flags for Exynos5433 SoC
arm64: dts: Add ARM PMU node for exynos7
TM2 can support the HS400 mode, but eMMC is working in the lowest mode.
This patch adds the properties for HS400 and other modes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the mshc_2 node for supporting T-Flash.
Also add the "mshc*" aliases. dwmmc driver should be assigned to
"ctrl_id" after parsing to "mshc". If there are no aliases for mshc,
then it might be set to the wrong capabilities.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j/xt
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Topic branch with DT arm64 changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for interrupt properties in exynos7
arm64: dts: exynos: Fix invalid GIC interrupt flags in exynos7
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device nodes for MFC video codec device to Exynos5433 SoC
dtsi and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for JPEG codec device to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for GScaler devices to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
UART3 device is not really needed for enabling audio block on TM2.
Enabling it made it working by enabling some common parent clocks,
what is now handled by improved exynos5433 clocks driver. Thus the UART3
device node can be safely disabled. The assigned-clocks entries are
however still needed, so move them under the respective CMU node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Without this patch the clkout clock is orphaned and sound doesn't
work properly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move initial FSYS CMU (related to USB 3.0 devices) clocks configuration
from generic exynos5433.dtsi file to exynos5433-tm2.dts, as this is
a board specific item.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Audio PLL and oscillator clocks are proper parent clocks for AUD CMU.
They are not visible as such on first glance on Exynos5433 SoC docs,
but they are needed for this CMU to operate properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch corrects FSYS CMU parent clocks specified in clock controller
node to let improved Exynos5433 clocks driver to control proper clocks
on FSYS<->TOP CMU boundary.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts. The
GIC requires shared interrupts to be edge rising or level high. Platform
declares support for both. Set all interrupts type to level high, as this
works fine - tested on Exynos5433-based TM2 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds ARM Performance Monitor Unit dt node for exynos7.
PMU provides various statistics on the operation of the CPU and
memory system at runtime, which are very useful when debugging or
profiling code. This enables the same.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed with "Add level for cpu dt node for exynos7"]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2E
board. TM2E board is very similar to the TM2 board so the
exynos5433-tm2e.dts includes the TM2 DTS and overrides the differences.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Use human-friendly symbols for interrupt flags.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ILIK
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree ARM64 update for v4.9" from Krzysztof Kozlowski:
1. Use human-friendly symbols for interrupt flags.
* tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for timer interrupt flags
Replace hex flags with human-readable symbols from arm-gic.h header
which makes it easier to recognize what is configured.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add RTC source clock as Exynos7 needs source (32.768KHz) clock
for RTC block. Without this currently S3C RTC driver probe is broken
on this SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Change the BUCK2 (vdd_atlas) voltage range to '500 - 1200mv' since
CPU DVFS requires it.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds device tree nodes for pdma0 and pdma1 controllers
found on exynos7 SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds TMU node, related temprature sensor and triping
point data for Atlas cpu core found on exynos7 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The ARMv8 Exynos family SoCs in Linux kernel are currently:
- Exynos5433 (controlled by ARCH_EXYNOS),
- Exynos7 (controlled by ARCH_EXYNOS7).
It duplicates Kconfig symbols unnecessarily, so consolidate them into
one ARCH_EXYNOS. Future SoCs could fall also under the ARCH_EXYNOS
symbol.
The commit should not bring any visible functional change.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
This patch add syscon-reboot node to reboot exynos7 based SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch enables HS200 mode operation on Exynos7 based
Espresso board.
This also removes _broken-cd_ property as per mmc binding documentation
which says one of the properties between broken-cd and non-removable
should be used. And we already use _non-removable_ as emmc is mounted
on the board which is a non-removable device.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds PMIC (S2MPS15) node on Espresso board,
which includes regulators and pmic-clk sub-nodes.
This patch also adds {vmmc,vqmmc}-supply properties for mmc2 node.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This adds BUS1 instance pinctrl for exynos7 soc.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add initial device tree nodes for exynos7 SoC and board dts file
to support espresso board based on exynos7 SoC.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
