The Sierra SERDES can be configured for QSGMII and SGMII protocols. Hence,
update the bindings to treat "PHY_TYPE_QSGMII" and "PHY_TYPE_SGMII" as
valid values for the "cdns,phy-type" property.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240930095145.3004053-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the bindings for STM32 COMBOPHY interface, used to support
the PCIe and USB3 stm32mp25 drivers.
Following entries can be used to tune caracterisation parameters
- st,output-micro-ohms and st,output-vswing-microvolt bindings entries
to tune the impedance and voltage swing using discrete simulation results
- st,rx-equalizer register to set the internal rx equalizer filter value.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Link: https://lore.kernel.org/r/20240930170847.948779-2-christian.bruel@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The usb phy in i.MX95 is compatible with i.MX8MP's, this will add a
compatible "fsl,imx95-usb-phy" for i.MX95. Also change reg maxItems
to 2 since i.MX95 needs another regmap to control Type-C Assist (TCA)
block. Since i.MX95 usb phy is able to switch SS lanes, this will also
add orientation-switch and port property to the file.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240911061720.495606-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here.) Other
than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvU0/g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGcACfSqouxRg8FRtq+nIKHWXI9lOTnVcAoKd9PAgq
1i7yCNopPEPEW8sjz1GX
=mY+S
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here)
Other than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
sub: cdns3: Use predefined PCI vendor ID constant
sub: cdns2: Use predefined PCI vendor ID constant
USB: misc: yurex: fix race between read and write
USB: misc: cypress_cy7c63: check for short transfer
USB: appledisplay: close race between probe and completion handler
USB: class: CDC-ACM: fix race between get_serial and set_serial
usb: r8a66597-hcd: make read-only const arrays static
usb: typec: ucsi: Fix busy loop on ASUS VivoBooks
usb: dwc3: rtk: Clean up error code in __get_dwc3_maximum_speed()
usb: storage: ene_ub6250: Fix right shift warnings
usb: roles: Improve the fix for a false positive recursive locking complaint
locking/mutex: Introduce mutex_init_with_key()
locking/mutex: Define mutex_init() once
net/9p/usbg: fix CONFIG_USB_GADGET dependency
usb: xhci: fix loss of data on Cadence xHC
usb: xHCI: add XHCI_RESET_ON_RESUME quirk for Phytium xHCI host
usb: dwc3: imx8mp: disable SS_CON and U3 wakeup for system sleep
usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode
usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk
usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support
...
- New Support
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
- Removal
- obsolete qcom,usb-8x16-phy bindings
- Updates
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmbv994ACgkQfBQHDyUj
g0eefhAApn1pj3AVJE+YBBNcRAZncxt/KdZmS0U8ErwVqlVbFCDJGJtCHOaKbPK+
K8c/u7vcElMA+JsqXd2biidlKsCmrkrpqqpPGJ08RlVy5TCa5H3UNONShPxU13g6
rP90CDJ6LpkOuU+p4b2jCVLVmY4Nq0g02OWUvuZDhFvR9FmfSVbRArmqWk+TdUW+
qO0oxxasNbh3nzt5HBwPUM+K2zZIzC7kQeJch69v3ETHeHzdGOlTKWEonU1OGnE9
PoeXubeSYW+fYaUbOg4n2Wgqt8330W3Flrhkd5Qp9cMAJEOe4Lqso3ai3jFW+iN4
bHQDcH3hzSpPNmlt2x8NgDamx/BEMbyAPQdnfVh7x4esxv+Zy/Fmg3XPeGf5BzlT
acis1nlAGnk/CpK+MurXgir8Si7gaiHH0n7lrginxr4QhBlT65Wzci0tPOYdivRH
4g8trmbLHX06Cji2XYvEjgm+Igekdyz892D6rSjOwYZS18CGgeJkdwVfyoMh984l
OVaU2d8N73J5UrP4zfUQV/FoOpqS6r+CbI0+f2CyPG+u6/Lwm7PT33ZZFof2s8/4
IiefpuwAzlPr8DEWa0j90VIGmVaTgmdYq3gdfRiG6P6fXoMkKMPLUbmZ9vFFMqRI
FiIe8K9gIyCRQadtUasUuVZ9vXr0jOHnbvCCbTmYSO/ceh+KU9I=
=XJmz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hw support:
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
Removed:
- obsolete qcom,usb-8x16-phy bindings
Updates:
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings"
* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
phy: ti: gmii-sel: Simplify with dev_err_probe()
phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
phy: mediatek: xsphy: Simplify with scoped for each OF child loop
phy: mediatek: tphy: Simplify with scoped for each OF child loop
phy: hisilicon: usb2: Simplify with scoped for each OF child loop
phy: cadence: sierra: Simplify with scoped for each OF child loop
phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
phy: qcom: qmp-pcie: Configure all tables on port B PHY
phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
dt-bindings: phy: socionext,uniphier: add top-level constraints
phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
...
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler;
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp: add support for BOE NE140WUM-N6G; revert support for
SDC ATNA45AF01
- visionox-vtdr6130: improve error handling; use
devm_regulator_bulk_get_const()
- boe-th101mb31ig002: Support for starry-er88577 MIPI-DSI panel plus
DT; Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1,
BOE NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da: Support Melfas lmfbx101117480 MIPI-DSI panel plus DT; Refactor
for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
support Innolux G070ACE-LH3 plus DT bindings
support On Tat Industrial Company KD50G21-40NT-A1 plus DT bindings
- st7701:
decouple DSI and DRM code
add SPI support
support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop: Support RGB display on Rockchip RK3066; Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc: Fix transparency after disabling plane; Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset
-----BEGIN PGP SIGNATURE-----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=7jR+
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"This adds a couple of patches outside the drm core, all should be
acked appropriately, the string and pstore ones are the main ones that
come to mind.
Otherwise it's the usual drivers, xe is getting enabled by default on
some new hardware, we've changed the device number handling to allow
more devices, and we added some optional rust code to create QR codes
in the panic handler, an idea first suggested I think 10 years ago :-)
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler:
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp:
- add support for BOE NE140WUM-N6G
- revert support for SDC ATNA45AF01
- visionox-vtdr6130:
- improve error handling
- use devm_regulator_bulk_get_const()
- boe-th101mb31ig002:
- Support for starry-er88577 MIPI-DSI panel plus DT
- Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1, BOE
NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da:
- Support Melfas lmfbx101117480 MIPI-DSI panel plus DT
- Refactor for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
- support Innolux G070ACE-LH3 plus DT bindings
- support On Tat Industrial Company KD50G21-40NT-A1 plus DT
bindings
- st7701:
- decouple DSI and DRM code
- add SPI support
- support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop:
- Support RGB display on Rockchip RK3066
- Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc:
- Fix transparency after disabling plane
- Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset"
* tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel: (1326 commits)
drm/xe: Fix missing conversion to xe_display_pm_runtime_resume
drm/xe/xe2hpg: Add Wa_15016589081
drm/xe: Don't keep stale pointer to bo->ggtt_node
drm/xe: fix missing 'xe_vm_put'
drm/xe: fix build warning with CONFIG_PM=n
drm/xe: Suppress missing outer rpm protection warning
drm/xe: prevent potential UAF in pf_provision_vf_ggtt()
drm/amd/display: Add all planes on CRTC to state for overlay cursor
drm/i915/bios: fix printk format width
drm/i915/display: Fix BMG CCS modifiers
drm/amdgpu: get rid of bogus includes of fdtable.h
drm/amdkfd: CRIU fixes
drm/amdgpu: fix a race in kfd_mem_export_dmabuf()
drm: new helper: drm_gem_prime_handle_to_dmabuf()
drm/amdgpu/atomfirmware: Silence UBSAN warning
drm/amdgpu: Fix kdoc entry in 'amdgpu_vm_cpu_prepare'
drm/amd/amdgpu: apply command submission parser for JPEG v1
drm/amd/amdgpu: apply command submission parser for JPEG v2+
drm/amd/pm: fix the pp_dpm_pcie issue on smu v14.0.2/3
drm/amd/pm: update the features set on smu v14.0.2/3
...
Corrected several typos in Documentation/devicetree/bindings files.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://lore.kernel.org/r/20240905151943.2792056-1-eleanor15x@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
i.MX7ULP need properly set System Integration Module(SIM) module to make
usb wakeup work well. This will add a "nxp,sim" property.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240903075810.1196928-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the RZ/G3S PHY bindings. The RZ/G3S USB PHY is almost identical
with the RZ/G2L USB PHY. The difference is that there is a hardware
limitation on the max burst size used when the BUS master interface
issues a transfer request for RZ/G3S that is configured though PHY
registers.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240822152801.602318-12-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add dt-bindings for USB2 PHY found on the Nuvoton MA35 SoC.
Signed-off-by: Hui-Ping Chen <hpchen0nvt@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240805030356.14565-2-hpchen0nvt@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Properties with variable number of items per each device are expected to
have widest constraints in top-level "properties:" block and further
customized (narrowed) in "if:then:". Add missing top-level constraints
for clock-names and reset-names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20240818172835.121757-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sixth PCIe instance on X1E80100 can be used in either 4-lane mode or
2-lane mode. Document the 4-lane mode as a separate compatible.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240823-x1e80100-phy-add-gen4x4-v3-1-b7765631ca01@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HDMI PHY can be used as a clock provider on RK3588 SoC, hence add
the necessary '#clock-cells' property.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-3-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the bindings for the Qualcomm 8x16 PHY driver that was dropped
in commit 4756f35fdf ("usb: phy: remove phy-qcom-8x16-usb.c") in 2017.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240711122016.41806-1-rayyan.ansari@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the hisilicon,hi3798cv200-combphy binding to DT schema format.
Drop the example as arm/hisilicon/controller/hi3798cv200-perictrl.yaml
already contains an example of this binding.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711152313.2364383-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the bindings for the SATA PHY on both apq8064 and ipq806x from
the old text format to yaml.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240715130854.53501-2-rayyan.ansari@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce Tx-Rx detection time and Rx AEQ mappings in Airoha EN7581
PCIe-PHY binding. This change is not introducing any backward compatibility
issue since the EN7581 dts is not upstream yet.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/a018329ff9678f3360bc6381294f95c62d34f3e3.1719682943.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a dedicated google,gs101-usb31drd-phy compatible for Google Tensor
gs101 SoC.
It needs additional clocks enabled for register access, and additional
memory regions (PCS & PMA) are required for successful configuration.
It also requires various power supplies (regulators) for the internal
circuitry to work. The required voltages are:
* pll-supply: 0.85V
* dvdd-usb20-supply: 0.85V (+10%, -7%)
* vddh-usb20-supply: 1.8V (+10%, -7%)
* vdd33-usb20-supply: 3.3V (+10%, -7%)
* vdda-usbdp-supply: 0.85V
* vddh-usbdp-supply: 1.8V
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-1-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add i.MX8QM and i.MX8QXP HSIO SerDes PHY binding.
Introduce one HSIO configuration 'fsl,hsio-cfg', which need be set at
initialization according to board design.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/1716962565-2084-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
StarFive SoCs like the jh7110 use a MIPI D-PHY TX
controller based on a M31 IP. Add a binding for it.
Signed-off-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240418035020.47876-2-shengyang.chen@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adds qcom,usb-hs-phy-msm8660 compatible
Used by HP Touchpad (tenderloin) for example.
Signed-off-by: Herman van Hazendonk <github.com@herrie.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240417065454.3599824-1-github.com@herrie.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need to specify exact name for the second (AUX) output
clock. It has never been used for the lookups based on the system clock
name. Partially revert commit 72bea132f3 ("dt-bindings: phy:
qcom,sc8280xp-qmp-pcie-phy: document PHY AUX clock on SM8[456]50 SoCs"),
returning compatibility with the existing device tree: reduce
clock-output-names to always contain a single entry.
Fixes: 72bea132f3 ("dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: document PHY AUX clock on SM8[456]50 SoCs")
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240614-fix-pcie-phy-compat-v3-2-730d1811acf4@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Armada CP110 UTMI supports swapping D+ and D- signals.
usb251xb.yaml already describes a suitable device-tree property for the
same purpose but as child usb controller node.
Add optional swap-dx-lanes device-tree property to armada cp110 utmi phy
with same semantics as usb251xb:
The property lists all ports that swap D+ and D-, unlisted ports are
considered correct.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240602-cn9130-som-v6-4-89393e86d4c7@solid-run.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Support for Embedded DisplayPort and DisplayPort submodes and driver
support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000 and
eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
- Updates
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for X1E80100,
SM8650 tables for UFS Gear 4 & 5 and correct voltage swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions
-----BEGIN PGP SIGNATURE-----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=og1j
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull generic phy updates from Vinod Koul:
"New HW Support:
- Support for Embedded DisplayPort and DisplayPort submodes and
driver support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000
and eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
Updates:
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for
X1E80100, SM8650 tables for UFS Gear 4 & 5 and correct voltage
swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions"
* tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (43 commits)
dt-bindings: phy: qcom,usb-snps-femto-v2: use correct fallback for sc8180x
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: fix msm899[68] power-domains
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: fix x1e80100-gen3x2 schema
phy: qcpm-qmp-usb: Add support for QDU1000/QRU1000
dt-bindings: phy: qcom,qmp-usb: Add QDU1000 USB3 PHY
dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for QDU1000
phy: qcom-qmp-pcie: add x4 lane EP support for sa8775p
phy: samsung-ufs: ufs: exit on first reported error
phy: samsung-ufs: ufs: remove superfluous mfd/syscon.h header
phy: rockchip: fix CONFIG_TYPEC dependency
phy: rockchip: usbdp: fix uninitialized variable
phy: rockchip-snps-pcie3: add support for rockchip,rx-common-refclk-mode
dt-bindings: phy: rockchip,pcie3-phy: add rockchip,rx-common-refclk-mode
phy: rockchip: add usbdp combo phy driver
dt-bindings: phy: add rockchip usbdp combo phy document
phy: add driver for MediaTek XFI T-PHY
dt-bindings: phy: mediatek,mt7988-xfi-tphy: add new bindings
phy: freescale: fsl-samsung-hdmi: Convert to platform remove callback returning void
phy: qcom: qmp-ufs: update SM8650 tables for Gear 4 & 5
MAINTAINERS: Add phy-gs101-ufs file to Tensor GS101.
...
DT Bindings:
- Convert samsung,exynos5-dp, atmel,lcdc, aspeed,ast2400-wdt bindings to
schemas
- Add bindings for Allwinner H616 NMI controller, Renesas r8a779g0 irqc,
Renesas R-Car V4M TMU and CMT timers, Freescale S32G3 linflexuart, and
Mediatek MT7988 XHCI
- Add 'reg' constraints on DSI and SPI display panels
- More dropping of unnecessary quotes in schemas
- Use full paths rather than relative paths in schema $refs
- Drop redundant storing of phandle for reserved memory
DT Core:
- Use scope based cleanups for kfree() and of_node_put()
- Track interrupt-map and power-supplies for fw_devlink
- Add buffer overflow check in of_modalias()
- Add and use __of_prop_free() helper for freeing struct property
-----BEGIN PGP SIGNATURE-----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=tslW
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Convert samsung,exynos5-dp, atmel,lcdc, aspeed,ast2400-wdt bindings
to schemas
- Add bindings for Allwinner H616 NMI controller, Renesas r8a779g0
irqc, Renesas R-Car V4M TMU and CMT timers, Freescale S32G3
linflexuart, and Mediatek MT7988 XHCI
- Add 'reg' constraints on DSI and SPI display panels
- More dropping of unnecessary quotes in schemas
- Use full paths rather than relative paths in schema $refs
- Drop redundant storing of phandle for reserved memory
DT Core:
- Use scope based cleanups for kfree() and of_node_put()
- Track interrupt-map and power-supplies for fw_devlink
- Add buffer overflow check in of_modalias()
- Add and use __of_prop_free() helper for freeing struct property"
* tag 'devicetree-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (25 commits)
of: property: Add fw_devlink support for interrupt-map property
dt-bindings: display: panel: constrain 'reg' in DSI panels
dt-bindings: display: panel: constrain 'reg' in SPI panels
dt-bindings: display: samsung,ams495qa01: add missing SPI properties ref
dt-bindings: Use full path to other schemas
dt-bindings: PCI: qcom,pcie-sm8350: Drop redundant 'oneOf' sub-schema
of: module: add buffer overflow check in of_modalias()
dt-bindings: PCI: microchip: increase number of items in ranges property
dt-bindings: Drop unnecessary quotes on keys
dt-bindings: interrupt-controller: mediatek,mt6577-sysirq: Drop unnecessary quotes
of: property: Use scope based cleanup on port_node
of: reserved_mem: Remove the use of phandle from the reserved_mem APIs
of: property: fw_devlink: Add support for "power-supplies" binding
dt-bindings: watchdog: aspeed,ast2400-wdt: Convert to DT schema
dt-bindings: irq: sun7i-nmi: Add binding for the H616 NMI controller
dt-bindings: interrupt-controller: renesas,irqc: Add r8a779g0 support
dt-bindings: timer: renesas,tmu: Add R-Car V4M support
dt-bindings: timer: renesas,cmt: Add R-Car V4M support
of: Use scope based of_node_put() cleanups
of: Use scope based kfree() cleanups
...
The Qualcomm MSM8996 and MSM8998 platforms don't have separate power
domain for the UFS PHY. Replace required:power-domains with the
conditional schema.
Fixes: dc5cb63592 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-2-f1fd15c33fb3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The qcom,x1e80100-qmp-gen3x2-pcie-phy device doesn't have second reset,
drop it from the clause enforcing second reset to be used.
Fixes: e94b29f2bd ("dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100 QMP PCIe PHYs")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-1-f1fd15c33fb3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the compatible string for USB phy found in Qualcomm
QDU/QRU1000 SoC.
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240502082017.13777-2-quic_kbajaj@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The yamllint quoted-strings check wasn't checking keys for quotes, but
support for checking keys was added in 1.34 release. Fix all the errors
found when enabling the check.
Clean-up the xilinx-versal-cpm formatting while we're here.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240426202239.2837516-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
>From the RK3588 Technical Reference Manual, Part1,
section 6.19 PCIe3PHY_GRF Register Description:
"rxX_cmn_refclk_mode"
RX common reference clock mode for lane X. This mode should be enabled
only when the far-end and near-end devices are running with a common
reference clock.
The hardware reset value for this field is 0x1 (enabled).
Note that this register field is only available on RK3588, not on RK3568.
The link training either fails or is highly unstable (link state will jump
continuously between L0 and recovery) when this mode is enabled while
using an endpoint running in Separate Reference Clock with No SSC (SRNS)
mode or Separate Reference Clock with SSC (SRIS) mode.
(Which is usually the case when using a real SoC as endpoint, e.g. the
RK3588 PCIe controller can run in both Root Complex and Endpoint mode.)
Add a rockchip specific property to enable/disable the rxX_cmn_refclk_mode
per lane. (Since this PHY supports bifurcation.)
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240412125818.17052-2-cassel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device tree binding document for Rockchip USBDP Combo PHY
with Samsung IP block.
Co-developed-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-2-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add bindings for the MediaTek XFI Ethernet SerDes T-PHY found in the
MediaTek MT7988 SoC which can operate at various interfaces modes:
via USXGMII PCS:
* USXGMII
* 10GBase-R
* 5GBase-R
via LynxI SGMII PCS:
* 2500Base-X
* 1000Base-X
* Cisco SGMII (MAC side)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/da5498096f71a40ca1eac4124b7bb601c82396fb.1712625857.git.daniel@makrotopia.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
QMP UFS PHY used in SC7180 requires 3 clocks:
* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC
This change obviously breaks the ABI, but it is inevitable since the
clock topology needs to be accurately described in the binding.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240401182240.55282-2-danila@jiaxyga.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock named
"PHY_AUX_CLK" which is an input of the Global Clock Controller (GCC) which
is muxed & gated then returned to the PHY as an input.
Document the clock IDs to select the PIPE clock or the AUX clock,
also enforce a second clock-output-names and a #clock-cells value of 1
for the PCIe Gen4x2 PHY found in the SM8[456]50 SoCs.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-1-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
access-controllers is an optional property that allows a peripheral to
refer to one or more domain access controller(s).
Description of this property is added to all peripheral binding files of
the peripheral under the STM32 firewall controller. It allows an accurate
representation of the hardware, where various peripherals are connected
to a firewall bus. The firewall can then check the peripheral accesses
before allowing its device to probe.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The Qualcomm X1E80100 platform has multiple PHYs that can work in both
eDP or DP mode, so document their compatible.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240221-phy-qualcomm-edp-x1e80100-v4-1-4e5018877bee@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a DT binding for the HDMI PHY found on the i.MX8MP SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Link: https://lore.kernel.org/r/20240227220444.77566-2-aford173@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds the bindings, for the MIPI CD-PHY module v0.5 embedded in
some Mediatek soc, such as the mt8365
Signed-off-by: Florian Sylvestre <fsylvestre@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240111101504.468169-2-jstephan@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI J7200 uses Torrent SD0805 version which is a special version derived
from Torrent SD0801 with some differences in register configurations.
Add a separate compatible for TI J7200 platforms.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All QMP UFS PHYs except MSM8996 require 3 clocks:
* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC or TCSR (since SM8550)
MSM8996 only requires 'ref' and 'qref' clocks. Hence, fix the binding to
reflect the actual clock topology.
This change obviously breaks the ABI, but it is inevitable since the
clock topology needs to be accurately described in the binding.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-1-58a49d2f4605@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Declare the registers accessible through the
TCSR space.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-2-a950c223f10f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation to defining the USB-C handling on MSM8998, QCM2290 and
SM6115 split existing QMP USB3 PHY schema into pure USB3 and USB-C
schema definitions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-3-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to some old SoCs with shared t-phy between usb3 and pcie only support
force-mode switch, and shared and non-shared t-phy may exist at the same
time on a SoC, can't use compatible to distinguish between shared and
non-shared t-phy, add a property to supported it.
Currently, only support switch from default pcie mode to usb3 mode.
But now prefer to use "mediatek,syscon-type" on new SoC as far as possible.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231211025624.28991-1-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the compatible string for MediaTek MT8195 SoC, using the same MIPI
D-PHY block as the MT8183.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231123133749.2030661-3-mwalle@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The amlogic,g12a-mipi-dphy-analog is a feature of the simple-mfd
amlogic,meson-axg-hhi-sysctrl system control register zone which is an
intermixed registers zone, thus it's very hard to define clear ranges for
each SoC controlled features even if possible.
The amlogic,g12a-mipi-dphy-analog was wrongly documented as an independent
register range, which is not the reality, thus fix the bindings by dropping
the reg property now it's referred from amlogic,meson-gx-hhi-sysctrl.yaml
and documented as a subnode of amlogic,meson-axg-hhi-sysctrl.
Also drop the unnecessary example, the top level bindings example should
be enough.
Fixes: 76ab79f972 ("dt-bindings: phy: add Amlogic G12A Analog MIPI D-PHY bindings")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231124-amlogic-v6-4-upstream-dsi-ccf-vim3-v9-4-95256ed139e6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since this bindings is referred from amlogic,meson-gx-hhi-sysctrl.yaml, drop the now
useless description about the parent node and also drop the unnecessary example.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231124-amlogic-v6-4-upstream-dsi-ccf-vim3-v9-3-95256ed139e6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for new
hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio, spi,
and i2c drivers for that type of device (all acked by the respective
subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems, EXCEPT for some merge conflicts that you will run
into in your tree. 2 of them are in device-tree files, which will be
trivial to resolve (accept both sides), and the last in the
drivers/gpio/gpio-ljca.c file, in the remove callback, resolution should
be pretty trivial (take the version in this branch), see here:
https://lore.kernel.org/all/20231016134159.11d8f849@canb.auug.org.au/
for details, or I can provide a resolved merge point if needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUStew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxgQCggUyfGo+JVV8XZVu5A9KwT6nr7mUAmwUgFxhZ
khK77t0KqF4hjXryeaHa
=iPd+
-----END PGP SIGNATURE-----
Merge tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
Convert the binding for the Marvell PXA1928 USB and HSIC PHYs from TXT
to DT schema.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231004-pxa1928-usb-yaml-v3-1-150c9ef3ab9d@skole.hr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The EUSB2 repeater requires some alterations to its init sequence,
depending on board design.
Add support for making the necessary changes to that sequence to make USB
functional on SM8550-based Xperia 1 V.
They all have lackluster description due to lack of information.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-1-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the 'reg is too long' warning caused by me adding 64-bit address and
size to the example, while default being 32-bit (cell size equal to 1).
Reported-by: Rob Herring <robh+dt@kernel.org>
Fixes: 505fb25416 ("dt-bindings: phy: migrate QMP PCIe PHY bindings to qcom,sc8280xp-qmp-pcie-phy.yaml")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230823181728.3082946-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Migrate legacy bindings (described in qcom,msm8996-qmp-usb3-phy.yaml)
to qcom,sc8280xp-qmp-usb3-uni-phy.yaml. This removes a need to declare
the child PHY node or split resource regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230824211952.1397699-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPIAOQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn80gCgybzMp0YnSildFetSC8lUJTnzjQcAn3KWzb75
Zt72jxGl4ZOXHEpozG4O
=FLrK
-----END PGP SIGNATURE-----
Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"
* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Correct also the format // -> .* in few Allwinner binding headers as
pointed out by checkpatch:
WARNING: Improper SPDX comment style for 'include/dt-bindings/reset/sun50i-h6-ccu.h', please use '/*' instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230823084540.112602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Document Exynos850 compatible. USB 2.0 DRD PHY on Exynos850 has two
clocks (ref and phy), which is already described in bindings.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-3-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Descrbie two PCIe PHYs found on the Qualcomm SM8150 platform, single
lane and two lanes Gen3 PHYs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Migrate legacy bindings (described in qcom,ipq8074-qmp-pcie-phy.yaml)
to qcom,sc8280xp-qmp-pcie-phy.yaml. This removes a need to declare
the child PHY node or split resource regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pattern for the nodename only allows t-phy@... , however, for the case
when the t-phy has no `reg` and only `ranges` (basically when the t-phy
is just a parent node), dtc will throw this warning:
Warning (unit_address_vs_reg): /t-phy@1a243000: node has a unit name, but no reg or ranges property
For a node like this:
sata_phy: t-phy@1a243000 {
ranges;
sata_port: sata-phy@1a243000 {
reg = <0 0x1a243000 0 0x0100>;
};
};
it is normal that the parent node 't-phy' would be without any address, as in:
sata_phy: t-phy {
ranges;
sata_port: sata-phy@1a243000 {
reg = <0 0x1a243000 0 0x0100>;
};
};
because being just a holder it does not have its own reg.
However the binding does not allow such a name for the t-phy, so with this
patch, making the `@[0-9a-f]+` part optional, such node is possible.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230814093931.9298-1-eugen.hristev@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix typos in Documentation/devicetree/bindings. The changes are in
descriptions or comments where they shouldn't affect functionality.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230814212822.193684-3-helgaas@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 3.0 PHY transceiver.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-5-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 2.0 PHY transceiver.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-4-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Migrate legacy bindings (described in qcom,sc7180-qmp-usb3-dp-phy.yaml)
to qcom,sc8280xp-qmp-usb43dp-phy.yaml. This removes a need to declare
the child PHY node or split resource regions.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
StarFive SoCs like the jh7110 use a MIPI D-PHY RX controller based on
a M31 IP. Add a binding for it.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718070803.16660-2-changhuang.liang@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the RK3568 PCIe v3 PHY supported has been upstreamed, RK3588
support was included, but the DT binding does not reflect this.
This adds the missing bits.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230717173512.65169-2-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Migrate legacy bindings (described in qcom,msm8996-qmp-ufs-phy.yaml)
to qcom,sc8280xp-qmp-ufs-phy.yaml. This removes a need to declare
the child PHY node or split resource regions.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711145153.4167820-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add StarFive JH7110 SoC PCIe 2.0 PHY dt-binding.
PCIe PHY0 (phy@10210000) can be used as USB 3.0 PHY.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230629075115.11934-3-minda.chen@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The qcom,msm8996-qmp-usb3-phy.yaml defines bindings for several PHYs
which predate USB -> USB+DP migration. Now as sm8150 has been migrated,
drop the legacy bindings completely. No device trees use them anymore.
Newer USB+DP bindings should use combo bindings from the beginning.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230531023415.1209301-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add bindings for sm8150 USB+DP PHY. These bindings follow the older
style as this is a quick conversion to simplify further driver cleanup.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230531023415.1209301-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574, IPQ9574 USB3 PHY
- Updates
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmSlyssACgkQfBQHDyUj
g0d6yg/9Ghx1aHTN3DgdXQ0DNSv79IlQXSMP3KXQJgRxmMbdJyVIv/FdnEYRnXFD
Rhvfal/fbBiGh7VskrcuYjW8ijQ4cSyvcgu+2FeuPoRq/0x7S3XMlw/2Fex6H1wU
wCS2V3RVuePEQRYeO3eVHQyVxWEa8Qk+2Ry0KG1s9DBIZgeMuU2f1FRED6p9Ayz8
Q1dBA/mVpPnEFhhIaO66IpvTLZ2M8x+mk0wFLtDl7f5ImFz0A7lM+Dfr42rJ0rWi
A1YbTSpEMTKVaoNKhAxrqdIEZzlQ/sPWiqeDwA+Ao9l1N8Dn0UWVJfXIuwBi/XzK
9552nsWwQE4ikiEU4+mxq7pZqrlT5kt8axxdvIC9MH70yRTdrEH34IbOb2IaD+GM
oKW++7ZVyeFmSmy5XezrgYbHzEdh2HBESUrbrLUg0qFOR+5lccDOI2KxOKx08Myw
pLpjROADwwUpa2PJ3hTRhCGURPXRVPQuB2Du7s1ILH6Fckeq9rIbmYEVcKUt8dgu
ZJXCRMG7nEKmT5G6XND7pHfFmt+oA4zdQxnUpBOgY64RIcllbpkv1smbJYlyqfKG
1pvOSkzriacldQSVSuzUiQ3CFgVN1+NjBBSLHDd5UWilEKVCjP5+gNpLhg2oAiXu
VK6j8MeHOmVgVH2V2kSnNU9oUBorddoMiTua7ci14NbwqVwwjUU=
=ReXo
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574,
IPQ9574 USB3 PHY
UpdatesL
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding"
* tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (67 commits)
dt-bindings: phy: brcm,brcmstb-usb-phy: Fix error in "compatible" conditional schema
dt-bindings: phy: mixel,mipi-dsi-phy: Remove assigned-clock* properties
dt-bindings: phy: intel,combo-phy: restrict node name suffixes
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
phy: tegra: xusb: check return value of devm_kzalloc()
phy: qcom: qmp-combo: fix Display Port PHY configuration for SM8550
phy: qcom: add the SGMII SerDes PHY driver
dt-bindings: phy: describe the Qualcomm SGMII PHY
phy: qualcomm: fix indentation in Makefile
phy: usb: suppress OC condition for 7439b2
phy: usb: Turn off phy when port is in suspend
phy: tegra: xusb: Clear the driver reference in usb-phy dev
dt-bindings: phy: mxs-usb-phy: add imx8ulp and imx8qm compatible
dt-bindings: phy: mxs-usb-phy: convert to DT schema format
dt-bindings: phy: qcom,qmp-usb: fix bindings error
dt-bindings: phy: qcom,qmp-ufs: fix the sc8180x regs
dt-bindings: phy: qcom,qmp-pcie: fix the sc8180x regs
phy: mediatek: tphy: add debugfs files
phy: core: add debugfs files
phy: fsl-imx8mp-usb: add support for phy tuning
...
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT schema
-----BEGIN PGP SIGNATURE-----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=cRW/
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT
schema
* tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: soc: qcom: stats: Update maintainer email
dt-bindings: cleanup DTS example whitespaces
dt-bindings: timestamp: restrict node name suffixes
dt-bindings: slimbus: restrict node name suffixes
dt-bindings: watchdog: restrict node name suffixes
dt-bindings: watchdog: brcm,kona-wdt: convert txt file to yaml
dt-bindings: watchdog: cdns,wdt-r1p2: Convert cadence watchdog to yaml
Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the hardware
in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKcVw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynEIQCgzJgnMCB81mirXlY1ZpCSDFqN8KIAnjRc27/1
vnUzldMQGY/FiS549gD9
=G3yz
-----END PGP SIGNATURE-----
Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
- Add support for the .remove_new callback to the ata_platform code to
simplify device removal interface (Uwe).
- Code simplification in ata_dev_revalidate() (Yahu)
- Fix code indentation and coding style in the pata_parport protocol
modules to avoid warnings from static code analyzers (me)
- Clarify ata_eh_qc_retry() behavior with better comments (Niklas)
- Simplify and improve ata_change_queue_depth() behavior to have a
consistent behavior between libsas managed devices and libata managed
devices (e.g. AHCI connected devices) (me).
- Cleanup libata-scsi and libata-eh code to use the ata_ncq_enabled()
and ata_ncq_supported() helpers instead of open coding flags tests
(me)
- Cleanup ahci_reset_controller() code (me).
- Change the pata_octeon_cf and sata_svw drivers to use
of_property_read_reg() to simplify the code (Rob, me).
- Remove unnecessary include files from ahci_octeon driver (me)
- Modify the DesignWare ahci dt bindings to add support for the
Rockchip RK3588 AHCI (Sebastian).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZJourwAKCRDdoc3SxdoY
dv43AQDzAFY0/0sjvqltGC31wRzzh/vEQFWsYt89Q4csMr4QgAEAkLO1gquH5/Wt
sxnCLh1WdFqbyNy6xsw+CXrfeREGDgo=
=IzEr
-----END PGP SIGNATURE-----
Merge tag 'ata-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Add support for the .remove_new callback to the ata_platform code to
simplify device removal interface (Uwe)
- Code simplification in ata_dev_revalidate() (Yahu)
- Fix code indentation and coding style in the pata_parport protocol
modules to avoid warnings from static code analyzers (me)
- Clarify ata_eh_qc_retry() behavior with better comments (Niklas)
- Simplify and improve ata_change_queue_depth() behavior to have a
consistent behavior between libsas managed devices and libata managed
devices (e.g. AHCI connected devices) (me)
- Cleanup libata-scsi and libata-eh code to use the ata_ncq_enabled()
and ata_ncq_supported() helpers instead of open coding flags tests
(me)
- Cleanup ahci_reset_controller() code (me)
- Change the pata_octeon_cf and sata_svw drivers to use
of_property_read_reg() to simplify the code (Rob, me)
- Remove unnecessary include files from ahci_octeon driver (me)
- Modify the DesignWare ahci dt bindings to add support for the
Rockchip RK3588 AHCI (Sebastian)
* tag 'ata-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (29 commits)
dt-bindings: phy: rockchip: rk3588 has two reset lines
dt-bindings: ata: dwc-ahci: add Rockchip RK3588
dt-bindings: ata: dwc-ahci: add PHY clocks
ata: ahci_octeon: Remove unnecessary include
ata: pata_octeon_cf: Add missing header include
ata: ahci: Cleanup ahci_reset_controller()
ata: Use of_property_read_reg() to parse "reg"
ata: libata-scsi: Use ata_ncq_supported in ata_scsi_dev_config()
ata: libata-eh: Use ata_ncq_enabled() in ata_eh_speed_down()
ata: libata-sata: Improve ata_change_queue_depth()
ata: libata-sata: Simplify ata_change_queue_depth()
ata: libata-eh: Clarify ata_eh_qc_retry() behavior at call site
ata: pata_parport: Fix on26 module code indentation and style
ata: pata_parport: Fix on20 module code indentation and style
ata: pata_parport: Fix ktti module code indentation and style
ata: pata_parport: Fix kbic module code indentation and style
ata: pata_parport: Fix friq module code indentation and style
ata: pata_parport: Fix fit3 module code indentation and style
ata: pata_parport: Fix fit2 module code indentation and style
ata: pata_parport: Fix epia module code indentation and style
...
The RK3588 has two reset lines for the combphy. One for the
APB interface and one for the actual PHY.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The conditional if/then schema has an error as the "enum" values have
"const" in them. Drop the "const".
Signed-off-by: Rob Herring <robh@kernel.org>
Fixes: 46b616c157 ("dt-bindings: phy: brcm, brcmstb-usb-phy: add BCM4908 binding")
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Message-ID: <20230621230958.3815818-1-robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With dt-schema v2021.02 these properties are added by default. Some SoC
(e.g. imx8mq) configure more than just one clock using these properties.
Fixes: f9b0593dd4 ("dt-bindings: phy: Convert mixel,mipi-dsi-phy to json-schema")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230609071538.149712-1-alexander.stein@ew.tq-group.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make the pattern matching node names a bit stricter to improve DTS
consistency. The pattern is restricted to:
1. Only one unit address or one -N suffix,
2. -N suffixes to decimal numbers.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530144851.92059-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The imx8ulp and imx8qm are compatible with imx8dxl. This will add such
compatible.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230613083445.1129137-2-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the binding to DT schema format. Besides, this also add clocks,
'#phy-cells', phy-3p0-supply and power-domains properties which are not
contained in txt file due to txt file lack updates.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230613083445.1129137-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge two allOf clauses, which sneaked in in two different patches.
Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml:109:1: found duplicate key "allOf" with value "[]" (original value: "[]")
Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml:109:1: [error] duplication of key "allOf" in mapping (key-duplicates)
Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml:109:1: found duplicate key "allOf" with value "[]" (original value: "[]")
Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml: ignoring, error parsing file
Fixes: 2daece5eb5 ("dt-bindings: phy: qcom,qmp-usb: Drop legacy bindings and move to newer one (SM6115 & QCM2290)")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230521195200.11967-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
orientation-switch it the standard declaration to inform the Type-C mux
layer that a remote-endpoint is capable of processing orientation change
messages.
Add as an optional since not all versions of the dp-phy currently support
the orientation-switch.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230515133643.3621656-4-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a compatible string for MediaTek Helio X10 MT6795: this SoC uses
the same DSI PHY as MT8173.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230412112739.160376-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
sc8180x ufs phy requires to describe five reg areas for the phy to work,
so move the description to the correct place documenting tx, rx lane
1, 2 and pcs.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230325122444.249507-8-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sc8180x pcie phy requires to describe six reg areas for the phy to work,
so move the description to the correct place documenting tx, rx lane 1,
2 and pcs and pcs misc.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230325122444.249507-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP combo phy can be connected to a TCPM, a USB controller and a
DisplayPort controller for handling USB Type-C orientation switching
and propagating HPD signals.
Extend the binding to allow these connections to be described.
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-2-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add cdns,usb2-disconnect-threshold-microvolt property to address fake USB
disconnection issue during enumeration or suspend state for difference
platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-7-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'qcom,msm8996-qmp-usb3-phy.yaml' defines bindings for several PHYs
which predate USB -> USB+DP migration. Since SM6115 and QCM2290
nodes for USB QMP phy are being added to dtsi files by followup patches,
move these bindings instead to the newer style
'qcom,sc8280xp-qmp-usb3-uni-phy.yaml' file.
Since no device trees use these bindings presently, so we have no ABI breakages
with this patch.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230516150511.2346357-2-bhupesh.sharma@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
maxItems is already globally set to 3. To make the binding easier to read
and remove redundancy, set minItems to 3 for sa8775p as this platform
requires exactly three clocks.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230419120914.173715-1-brgl@bgdev.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At least on SC8280XP the eDP PHY is part of power domain:
sc8280xp-crd.dtb: phy@220c2a00: 'power-domains' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230416151233.346336-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible string for Qualcomm QMP Super Speed (SS) UNI PHY found
in SA8775P.
Signed-off-by: Shazad Hussain <quic_shazhuss@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230428130824.23803-4-quic_shazhuss@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the compatible string for USB phy found in Qualcomm SA8775P SoC
Signed-off-by: Shazad Hussain <quic_shazhuss@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230428130824.23803-3-quic_shazhuss@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert Broadcom Kona family USB 2.0 PHY bindings to DT schema.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230427190725.GA7730@standask-GA-A55M-S2HP
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New support:
- UFS PHY for Qualcomm SA8775p, SM7150
- PCIe 2 lane phy support for sc8180x and PCIe PHY for SDX65
- Mediatke hdmi phy support for mt8195
- rockchip naneng combo phy support for RK358
- Updates:
- Drop Thunder Bay eMMC PHY driver
- RC support for PCIe phy for Qualcomm SDX55
- SGMII support in WIZ driver for J721E
- PCIe and multilink SGMII PHY support in cadence driver
- Big pile of platform remove callback returning void conversions
-----BEGIN PGP SIGNATURE-----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=WwgW
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New support:
- UFS PHY for Qualcomm SA8775p, SM7150
- PCIe 2 lane phy support for sc8180x and PCIe PHY for SDX65
- Mediatke hdmi phy support for mt8195
- rockchip naneng combo phy support for RK358
Updates:
- Drop Thunder Bay eMMC PHY driver
- RC support for PCIe phy for Qualcomm SDX55
- SGMII support in WIZ driver for J721E
- PCIe and multilink SGMII PHY support in cadence driver
- Big pile of platform remove callback returning void conversions"
* tag 'phy-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits)
phy: cadence: cdns-dphy-rx: Add common module reset support
phy: ti: j721e-wiz: Add SGMII support in WIZ driver for J721E
dt-bindings: phy: ti: phy-gmii-sel: Add support for J784S4 CPSW9G
phy: ti: j721e-wiz: Fix unreachable code in wiz_mode_select()
phy: cadence: Sierra: Add PCIe + SGMII PHY multilink configuration
phy: mediatek: add support for phy-mtk-hdmi-mt8195
phy: phy-mtk-hdmi: Add generic phy configure callback
dt-bindings: phy: mediatek: hdmi-phy: Add mt8195 compatible
phy: tegra: xusb: Add missing tegra_xusb_port_unregister for usb2_port and ulpi_port
dt-bindings: phy: ti,phy-j721e-wiz: document clock-output-names
dt-bindings: phy: ti,phy-j721e-wiz: drop assigned-clocks
dt-bindings: phy: ti,phy-am654-serdes: drop assigned-clocks type
dt-bindings: phy: cadence-torrent: drop assigned-clocks
dt-bindings: phy: cadence-sierra: drop assigned-clocks
phy: rockchip: remove unused hw_to_inno function
phy: qualcomm: phy-qcom-qmp-ufs: add definitions for sa8775p
dt-bindings: phy: qmp-ufs: describe the UFS PHY for sa8775p
phy: qcom-qmp-pcie: drop sdm845_qhp_pcie_rx_tbl
phy: qcom-qmp-pcie: sc8180x PCIe PHY has 2 lanes
phy: qcom-qmp-ufs: Add SM7150 support
...
The CPSW9G instance of CPSW Ethernet Switch on TI's J784S4 SoC supports
additional PHY modes like QSGMII. Add a compatible for it.
Enable the use of "ti,qsgmii-main-ports" property for J784S4 CPSW9G.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230315092408.1722114-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a compatible for the HDMI PHY on MT8195
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20220919-v8-1-a84c80468fe9@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the clock-output-names property of clock children, even though
the nodes are actually deprecated, to fix dtbs_check warnings like:
k3-j7200-common-proc-board.dtb: wiz@5060000: refclk-dig: 'clock-output-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404190115.546973-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The meta schema from DT schema already defines assigned-clocks, so there
is no need for device schema to mention it at all. There are also no
benefits of having it here and a board could actually need more of clock
assignments than the schema allows.
Keep however the assigned-clocks in children nodes, as apparently their
proper parenting is required.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404190115.546973-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The meta schema from DT schema already defines assigned-clocks, so there
is no need for device schema to mention it at all. The specific
parenting of the first input and output clock is apparently important,
thus keep them as required, but without defining type.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404190115.546973-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The meta schema from DT schema already defines assigned-clocks, so there
is no need for device schema to mention it at all. There are also no
benefits of having it here and a board could actually need more of clock
assignments than the schema allows.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404190115.546973-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The meta schema from DT schema already defines assigned-clocks, so there
is no need for device schema to mention it at all. There are also no
benefits of having it here and a board could actually need more of clock
assignments than the schema allows.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404190115.546973-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a new compatible for the QMP UFS PHY found on sa8775p platforms and
update the clocks property to accommodate three clocks.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230411130446.401440-3-brgl@bgdev.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
RK3568 Naneng Combo Phy driver can support RK3588 with the additional
clocks and initial configuration, so add the compatible line.
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230314135555.44162-3-lucas.tanure@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
