Implements SmmCpuSyncLib Library instance. The instance refers the
existing SMM CPU driver (PiSmmCpuDxeSmm) sync implementation
and behavior:
1.Abstract Counter and Run semaphores into SmmCpuSyncCtx.
2.Abstract CPU arrival count operation to
SmmCpuSyncGetArrivedCpuCount(), SmmCpuSyncCheckInCpu(),
SmmCpuSyncCheckOutCpu(), SmmCpuSyncLockDoor().
Implementation is aligned with existing SMM CPU driver.
3. Abstract SMM CPU Sync flow to:
BSP: SmmCpuSyncReleaseOneAp --> AP: SmmCpuSyncWaitForBsp
BSP: SmmCpuSyncWaitForAPs <-- AP: SmmCpuSyncReleaseBsp
Semaphores release & wait during sync flow is same as existing SMM
CPU driver.
4.Same operation to Counter and Run semaphores by leverage the atomic
compare exchange.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch is to complete 170d4ce8, sync the change to BaseXApicLib.
Checking the max cpuid leaf is not enough to figure whenever
CPUID_V2_EXTENDED_TOPOLOGY is supported. Intel SDM says:
Software must detect the presence of CPUID leaf 1FH by verifying
(a) the highest leaf index supported by CPUID is >= 1FH, and
(b) CPUID.1FH:EBX[15:0] reports a non-zero value.
The same is true for CPUID leaf 0BH.
This patch adds the EBX check to GetProcessorLocation2ByApicId(). The
patch also fixes the existing check in GetProcessorLocationByApicId() to
be in line with the spec by looking at bits 15:0. The comments are
updated with a quote from the Intel SDM.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Message-Id: <20231115111553.6592-2-jiaxin.wu@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Refine test case:
1. Check PAE paging reserved bits is zero.
2. Set stack as random value.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The local variable OneOfPagingEntry is used before initialized, this
may cause reserved bit in page table entry is set especially in PAE
paging mode. The bug is random because it depends on the value in
stack.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
With SEV-SNP, the SEV-ES save area for a vCPU should be unique to that
vCPU. After commit 3323359a81, the VMSA allocation was re-used, but when
sorting the CPUs by APIC ID, the save area was not updated to follow the
original CPU. Similar to the StartupApSignal address, the SevEsSaveArea
address should be updated when sorting the CPUs.
This does not cause an issue at this time because all APs are in HLT state
and then are (re)started at the same time, with the same VMSA contents.
However, this should be fixed to account for any change in future
behavior.
Fixes: 3323359a81 ("UefiCpuPkg/MpInitLib: Reuse VMSA allocation to ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The CPUID_EXTENDED_TOPOLOGY CPUID leaf takes a subleaf as input when
returning CPUID information. However, the AsmCpuid() function does not
zero out ECX before the CPUID instruction, so the input leaf is used as
the sub-leaf for the CPUID request and returns erroneous/invalid CPUID
data, since the intent of the request was to get data related to sub-leaf
0. Instead, use AsmCpuidEx() for the CPUID_EXTENDED_TOPOLOGY leaf.
Fixes: d4d7c9ad5f ("UefiCpuPkg/MpInitLib: use BSP to do extended ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
No functional changes in this patch.
Updates the comments of _CPU_MP_DATA to delcared that duplications in
CpuMpData are present to avoid to be direct accessed and comprehended
in assembly code. CpuMpData: Intended for use in C code while
ExchangeInfo are used in assembly code in this module.
This patch deletes the unnecessary comments in CpuMpData, since
CpuMpData is no longer responsible for passing information from PEI to
DXE.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Laszlo Ersek lersek@redhat.com
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
This patch synchronizes the No-Execute bit in the IA32_EFER
register for the APs before the RestoreVolatileRegisters operation.
The commit 964a4f0, titled "Eliminate the second INIT-SIPI-SIPI
sequence," replaces the second INIT-SIPI-SIPI sequence with the BSP
calling the SwitchApContext function to initiate a specialized start-up
signal, waking up APs in the DXE instead of using INIT-SIPI-SIPI.
Due to this change, the logic for "Enable execute disable bit" in
MpFuncs.nasm is no longer executed. However, to ensure the proper setup
of the page table, it is necessary to synchronize the IA32_EFER.NXE for
APs before executing RestoreVolatileRegisters .
Based on SDM:
If IA32_EFER.NXE is set to 1, it signifies execute-disable, meaning
instruction fetches are not allowed from the 4-KByte page controlled by
this entry. Conversely, if it is set to 0, it is reserved.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek lersek@redhat.com
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Aim:
- To solve the assertion that checks if CpuMpData->FinishedCount
equals (CpuMpData->CpuCount - 1). The assertion arises from a timing
discrepancy between the BSP's completion of startup signal checks and
the APs' incrementation of the FinishedCount.
- This patch also ensures that "finished" reporting from the APs is as
later as possible.
More specifially:
In the SwitchApContext() function, the BSP trigers
the startup signal and check whether the APs have received it. After
completing this check, the BSP then verifies if the FinishedCount is
equal to CpuCount-1.
On the AP side, upon receiving the startup signal, they invoke
SwitchContextPerAp() and increase the FinishedCount to indicate their
activation. However, even when all APs have received the startup signal,
they might not have finished incrementing the FinishedCount. This timing
gap results in the triggering of the assertion.
Solution:
Instead of assertion, use while loop to waits until all the APs have
incremented the FinishedCount.
Fixes: 964a4f032d
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <20231025114216.2824-1-yuanhao.xie@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Checking the max cpuid leaf is not enough to figure whenever
CPUID_V2_EXTENDED_TOPOLOGY is supported. Intel SDM says:
Software must detect the presence of CPUID leaf 1FH by verifying
(a) the highest leaf index supported by CPUID is >= 1FH, and
(b) CPUID.1FH:EBX[15:0] reports a non-zero value.
The same is true for CPUID leaf 0BH.
This patch adds the EBX check to GetProcessorLocation2ByApicId(). The
patch also fixes the existing check in GetProcessorLocationByApicId() to
be in line with the spec by looking at bits 15:0. The comments are
updated with a quote from the Intel SDM.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2241388
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20231017112807.1244254-1-kraxel@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Introduce a PCD to control the maximum SATP mode that MMU allowed
to use. This PCD helps RISC-V platform set bare or minimum SATP mode
during bring up to debug memory map issue.
Signed-off-by: Tuan Phan <tphan@ventanamicro.com>
Reviewed-by: Dhaval Sharma <dhaval@rivosinc.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
attributes
Add Unit test of trrGetMemoryAttributesInMtrrSettings and
MtrrSetMemoryAttributesInMtrrSettings.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Improve MtrrDebugPrintAllMtrrsWorker by making use of
MtrrGetMemoryAttributesInMtrrSettings.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
MtrrGetMemoryAttributesInMtrrSettings parses the MTRR settings
either from hardware or from the parameter and returns an
array containing the memory cache types of all memory addresses.
This API could elinimate the needs of following APIs:
1. MtrrGetMemoryAttributeInVariableMtr
2. MtrrGetFixedMtrr
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update APIs related to set memory attributes to handle the fixed MTRR
is not always supported.
There are 3 APIs in MtrrLib that can set memory attributes:
1. MtrrSetMemoryAttributesInMtrrSettings
2. MtrrSetMemoryAttributeInMtrrSettings
3. MtrrSetMemoryAttribute
The general idea applied in MtrrSetMemoryAttributesInMtrrSettings is:
1. MtrrLibPreMtrrChange saves the old MTRR default type which
contains bit to enable fixed MTRR.
2. Main logic in MtrrSetMemoryAttributesInMtrrSettings applies
memory attribute settings for below 1MB to variable MTRRs
if fixed MTRR is not supported.
3. MtrrLibPostMtrrChange unconditionally sets E bit in MTRR default
type MSR but only set FE bit when fixed MTRRs are modified.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update UnitTestMtrrSetAllMtrrs() for the case that fixed MtrrLib
is not always supported.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update MtrrSetAllMtrrs to not access fixed MTRRs if CPU doesn't
support them.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
UnitTestMtrrGetFixedMtrr updated for the case that fixed MtrrLib
is not always supported.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
IsMtrrSupported() return true when either fixed mtrr supported or
variable mtrr suppored. In this case, rather than checking whether
MTRR is supported or not, we should specifically check for fixed MTRR
support.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update UnitTestMtrrGetAllMtrrs() for the case that fixed MtrrLib
is not always supported
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The patch fixes the following issues in the original implementation:
1. MtrrSetting contains random value if MTRR is not supported.
2. Unconditionally access fixed MTRR on CPU that may not support
fixed MTRR.
3. The maximum number of Variable MTRR entries are initialized, while
the portion exceeding the maximum number remains uninitialized.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update UnitTestMtrrGetDefaultMemoryType for the case the when Fixed
MTRRs are not supported.
The original implementation returns FALSE when either fixed MTRR isn't
supported or the number of variable MTRRs is 0. The correct behavior
should return FALSE only when both fixed MTRR isn't supported and the
number of variable MTRRs is 0.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Update UnitTestGetFirmwareVariableMtrrCount for the case the when
Fixed MTRRs are not supported.
The original implementation returns FALSE when either fixed MTRR isn't
supported or the number of variable MTRRs is 0. The correct behavior
should return FALSE only when both fixed MTRR isn't supported and the
number of variable MTRRs is 0.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The previous implementation returns FALSE if either fixed MTRR is
unsupported or the number of variable MTRRs is 0. The correct behavior
is to return FALSE only when both fixed MTRR is unsupported and the
number of variable MTRRs is 0.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add internal function MtrrLibIsMtrrSupported and
update IsMtrrSupported to call the new internal function.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The implementation of this new behavior aligns with the guidelines
outlined in the Intel SDM.
Following a power-up or RESET of an MP system, system hardware
dynamically selects one of the processors on the system bus as the BSP.
The remaining processors are designated as APs. The APs complete a
minimal self-configuration, then wait for a startup signal (a SIPI
message) from the BSP processor.
Additionally, the MP protocol is executed only after
a power-up or RESET. If the MP protocol has completed and a
BSP is chosen, subsequent INITs (either to a specific processor or
system wide) do not cause the MP protocol to be repeated. Instead, each
logical processor examines its BSP flag (in the IA32_APIC_BASE MSR) to
determine whether it should execute the BIOS boot-strap code (if it is
the BSP) or enter a wait-for-SIPI state (if it is an AP).
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add PcdFirstTimeWakeUpAPsBySipi to check if it is in the OVMF environment
and necessary to wake up APs by INIT-SIPI-SIPI.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add new API SendStartupIpiAllExcludingSelf(), and modify
SendInitSipiSipiAllExcludingSelf() by let it call the new API.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The purpose is to fix an issue where an exception occurs at the start
of the DXE phase by applying the following patch series on INTEL-based
systems.
UefiCpuPkg: Refactor the logic for placing APs in HltLoop.
UefiCpuPkg: Refactor the logic for placing APs in Mwait/Runloop.
UefiCpuPkg: Create MpHandOff.
UefiCpuPkg: ApWakeupFunction directly use CpuMpData.
UefiCpuPkg: Eliminate the second INIT-SIPI-SIPI sequence.
This series of patches makes changes to the way the APs are
initialized and woken up. It removes the 2nd time INIT-SIPI-SIPI and
introduces a special startup signal to wake up APs. These patches also
create a new HOB identified by the mMpHandOffGuid, which stores only the
minimum information required from the PEI phase to the DXE phase.
As a result, the original HOB (mCpuInitMpLibHobGuid) is now used only
as a global variable in the PEI phase and is no longer necessary in the
DXE phase for INTEL-based systems. The AMD SEV-ES related code
still relies on the OldCpuMpData in the DXE phase.
This patch decouple the SEV-ES functionality of assigning CpuMpData to
OldCpuMpData->NewCpuMpData from the Intel logic.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
During CpuDxe initialization, MMU will be setup with the highest
mode that HW supports.
Signed-off-by: Tuan Phan <tphan@ventanamicro.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
When both the PEI and DXE phases operate in the same execution
mode(32-bit/64-bit), the BSP send a special start-up signal during
the DXE phase to awaken the Application APs.
To eliminate the need for the INIT-SIPI-SIPI sequence at the beginning
of the DXE phase, the BSP call the SwitchApContext function to trigger
the special start-up signal. By writing the specified
StartupSignalValue to the designated StartupSignalAddress, the BSP
wakes up the APs from mwait mode. Once the APs receive the
MP_HAND_OFF_SIGNAL value, they are awakened and proceed to execute the
SwitchContextPerAp procedure. They enter another while loop,
transitioning their context from the PEI phase to the DXE phase.
The original state transitions for an AP during the procedure are as
follows:
Idle ----> Ready ----> Busy ----> Idle
[BSP] [AP] [AP]
Instead of init-sipi-sipi sequence, we make use of a
start-up signal to awaken the APs and transfer their context from
PEI to DXE. Consequently, APs, rather than the BSP, to set their state
to CpuStateReady.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
In the original design, once the APs finished executing their assembly
code and switched to executing C code, they would enter a continuous
loop within a function. In this function, they would collect CpuMpData
using the MP_CPU_EXCHANGE_INFO mechanism. However, in the updated
approach, CpuMpData can now be passed directly to the ApWakeUpFunction,
bypassing the need for MP_CPU_EXCHANGE_INFO. This modification is made
in preparation for eliminating the requirement of a second
INIT-SIPI-SIPI sequence in the DXE phase.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Initially, the purpose of the Hob was twofold: it served as a way to
transfer information from PEI to DXE. However, during the DXE phase,
only a few fields from the CPU_MP_DATA which collected in PEI phase were
needed. A new Hob was specifically created to transfer information
to the DXE phase. This new Hob contained only the essential fields
required for reuse in DXE. For instance, instead of directly including
the BspNumber in MpHandOff, the DXE phase introduced the use of
GetBspNumber() to collect the BspNumber from ApicID and CpuCount.
The SaveCpuMpData() function was updated to construct the MP_HAND_OFF
Hob. Additionally, the function introduced the MP_HAND_OFF_SIGNAL,
which solely served the purpose of awakening the APs
and transitioning their context from PEI to DXE. The
WaitLoopExecutionMode field indicated whether the bit mode of PEI
matched that of DXE. Both of them were filled only if the ApLoopMode
was not ApInHltLoop. In the case of ApInHltLoop, it remained necessary
to wake up the APs using the init-sipi-sipi sequence. This improvement
still allow INIT-SIPI-SIPI even APs are wait in Run/Mwait loop mode.
The function GetMpHandOffHob() was added to facilitate access to the
collected MpHandOff in the DXE phase. The CpuMpData in the DXE phase
was updated by gathering information from MpHandOff. Since MpHandOff
replaced the usage of OldCpuMpData and contained essential information
from the PEI phase to the DXE phase. AmdSevUpdateCpuMpData was included
to maintain the original implementation of AmdSev, ensuring that
OldCpuMpData->NewCpuMpData pointed to CpuMpData.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in
Mwait/Runloop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in HltLoop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Removes SmmCpuFeaturesReadSaveStateRegister and
SmmCpuFeaturesWirteSaveStateRegister function from
SmmCpuFeaturesLib library.
MmSaveStateLib library replaces the functionality of the above
functions.
Platform old/new need to use MmSaveStateLib library to read/write save
state registers.
Current implementation supports Intel and AMD.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Implements MmSaveStateLib library interfaces
to read and write save state
registers for Intel processor family.
Moves Intel and AMD common functionality to common area.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
Implements interfaces to read and write save state
registers of AMD's processor family.
Initializes processor SMMADDR and MASK depends
on PcdSmrrEnable flag.
Program or corrects the IP once control returns from SMM.
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Abdul Lateef Attar <abdattar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4182
moves Intel-specific code to the arch-dependent file.
Other processor families might have different
implementation of these functions.
Hence, moving out of the common file.
Cc: Abner Chang <abner.chang@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Abdul Lateef Attar <AbdulLateef.Attar@amd.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The timer compare register is 64-bit so simplifying the delay
function.
Cc: Andrei Warkentin <andrei.warkentin@intel.com>
Signed-off-by: Tuan Phan <tphan@ventanamicro.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Update ProcTrace feature code to support enable collect performance
data by generating CYC and TSC packets. Add a new dynamic
PCD to indicate if enable performance collecting. In ProcTrace.c
code, if this new PCD is true, after check cpuid, CYC and TSC
packets will be generated by setting the corresponding MSR bits
feilds if supported.
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=4423
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Xiao X Chen <xiao.x.chen@intel.com>
Update code to support enable ProcTrace only on BSP. Add a new
dynamic PCD to indicate if enable ProcTrace only on BSP. In
ProcTrace.c code, if this new PCD is true, only allocate buffer
and set CtrlReg.Bits.TraceEn to 1 for BSP.
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=4423
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Xiao X Chen <xiao.x.chen@intel.com>
Because UefiCpuPkg/UefiCpuLib is merged to MdePkg/CpuLib and all modules
are updated to not depend on this library, remove it completely.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
__FUNCTION__ is a pre-standard extension that gcc and Visual C++ among
others support, while __func__ was standardized in C99.
Since it's more standard, replace __FUNCTION__ with __func__ throughout
UefiCpuPkg.
Signed-off-by: Rebecca Cran <rebecca@bsdio.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
The CPU exception handler library code was rewritten at some point to
populate the vector code templates with absolute references at runtime,
given that the XCODE linker does not permit absolute references in
executable code when creating PIE executables.
This is rather unfortunate, as this prevents us from using strict
permissions on the memory mappings, given that the .text section needs
to be writable at runtime for this arrangement to work.
So let's make this hack XCODE-only, by setting a preprocessor #define
from the command line when using the XCODE toolchain, and only including
the runtime fixup code when the macro is defined.
While at it, rename the Xcode5ExceptionHandlerAsm.nasm source file and
drop the Xcode5 prefix: this code is used by other toolchains too.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The PEI flavor of CpuExceptionHandlerLib never populates more than 32
IDT vectors, and there is no CET shadow stack support in the PEI phase.
So there is no need to use the generic ExceptionHandler NASM source,
which carries a 256-entry template and CET support, and writes to its
own .text section when built using XCODE, which is not permitted in the
PEI phase. So let's switch to the reduced SEC/PEI version of this
component, which is sufficient for PEI and doesn't suffer from the same
issue.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Currently, we use the non-Xcode5 version of ExceptionHandlerAsm.nasm
only for the SEC and PEI phases, and this version was not compatible
with the XCODE or LLD linkers, which do not permit absolute relocations
in read-only sections.
Given that SEC and PEI code typically executes in place from flash and
does not use page alignment for sections, we can simply emit the code
carrying the absolute symbol references into the .data segment instead.
This works around the linker's objections, and the resulting image will
be mapped executable in its entirety anyway. Since this is only needed
for XCODE, let's make this change conditionally using a preprocessor
macro.
Let's rename the .nasm file to reflect the fact that is used for the
SecPei flavor of this library only, and while at it, remove some
unnecessary absolute references.
Also update the Xcode specific version of this library, and use this
source file instead. This is necesessary, as the Xcode specific version
modifies its own code at runtime, which is not permitted in SEC or PEI.
Note that this also removes CET support from the Xcode5 specific build
of the SEC/PEI version of this library, but this is not needed this
early in any case, and this aligns it with other toolchains, which use
this version of the library, which does not have CET support either.
1. Change for non-XCODE SecPeiCpuExceptionHandlerLib:
. Use SecPeiExceptionHandlerAsm.nasm (renamed from
ExceptionHandlerAsm.nasm)
. Removed some unnecessary absolute references
(32 IDT stubs are still in .text.)
2. Change for XCODE SecPeiCpuExceptionHandlerLib:
. Use SecPeiExceptionHandlerAsm.nasm instead of
Xcode5ExceptionHandlerAsm.nasm
. CET logic is not in SecPeiExceptionHandlerAsm.nasm (but aligns to
non-XCODE lib instance)
. Fixed a bug that does runtime fixup in TEXT section in SPI flash.
. Emitted the code carrying the absolute symbol references into the
.data which XCODE or LLD linkers allow.
. Then fixup can be done by other build tools such as GenFv if the code
runs in SPI flash, or by PE coff loader if the code is loaded to
memory.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Drop MtrrLibIsPowerOfTwo function, use the new IS_POW2() macro instead.
The ASSERT() removed (inside MtrrLibIsPowerOfTwo) is superfluous,
another ASSERT() a few lines up in MtrrLibCalculateMtrrs() already
guarantees that Length can not be zero at this point.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4353
Due to AMD erratum #1467, an SEV-SNP VMSA should not be 2MB aligned. To
work around this issue, allocate two pages instead of one. Because of the
way that page allocation is implemented, always try to use the second
page. If the second page is not 2MB aligned, free the first page and use
the second page. If the second page is 2MB aligned, free the second page
and use the first page. Freeing in this way reduces holes in the memory
map.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=4353
When parking the APs on exiting from UEFI, a new page allocation is made.
This allocation, however, does not end up being marked reserved in the
memory map supplied to the OS. To avoid this, re-use the VMSA by clearing
the VMSA RMP flag, updating the page contents and re-setting the VMSA RMP
flag.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
When TME-MK is enabled, the MtrrLib should substract the TME-MK
reserved bits from the max PA returned from CPUID instruction.
The new test case guarantees such behavior in MtrrLib.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
CPUID enumeration of MAX_PA is unaffected by TME-MK activation and
will continue to report the maximum physical address bits available
for software to use, irrespective of the number of KeyID bits.
So, we need to check if TME is enabled and adjust the PA size
accordingly.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
MtrrLib code queries the CPUID leaf 7h result if support.
Update Test code temporary to claim the CPUID only
supports max leaf as 1 so MtrrLib skips to query CPUID leaf 7h.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Ahmad Anadani <ahmad.anadani@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
The random test cases just run for too long that may cause timeout
in CI test.
Disable them for now.
Co-authored-by: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Sean Brogan <sean.brogan@microsoft.com>
Reduce the number of random tests. In previous patch, non-1:1
mapping is enbaled and it may need more than an hour and a half
for the CI test, which may lead to CI timeout. Reduce the number
of random test count to pass the CI.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add RandomTest for PAE paging.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Modify CpuPageTableLib code to enable PAE paging.
In PageTableMap() API:
When creating new PAE page table, after creating page table,
set all MustBeZero fields of 4 PDPTE to 0. The MustBeZero
fields are treated as RW and other attributes by the common
map logic. So they might be set to 1.
When updating exsiting PAE page table, the special steps are:
1.Prepare 4K-aligned 32bytes memory in stack for 4 temp PDPTE.
2.Copy original 4 PDPTE to the 4 temp PDPTE and set the RW,
UserSupervisor to 1 and set Nx of 4 temp PDPTE to 0.
4.After updating the page table, set the MustBeZero fields of
4 temp PDPTE to 0.
5.Copy the temp PDPTE to original PDPTE.
In PageTableParse() API, also create 4 temp PDPTE in stack.
Copy original 4 PDPTE to the 4 temp PDPTE. Then set the RW,
UserSupervisor to 1 and set Nx of 4 temp PDPTE to 0. Finally
use the address of temp PDPTE as the page table address.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Combine 'if' condition branch for non-present and leaf Parent
Entry in PageTableLibMapInLevel. Most steps of these two condition
are the same. This commit doesn't change any functionality.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add code to compare ParentPagingEntry Attribute&Mask and input
Attribute&Mask to decide if new next level page table is needed
in non-present ParentPagingEntry condition. This can help avoid
unneccessary page table creation.
For example, there is a page table in which [0, 1G] is mapped(Lv4[0]
,Lv3[0,0], a non-leaf level4 entry and a leaf level3 entry).And we
only want to map [1G, 1G+2M] linear address still as non-present.
The expected behaviour should be nothing happens in the process.
However, previous code logic doesn't check if ParentPagingEntry
Attribute&Mask and input Attribute&Mask are the same in non-present
ParentPagingEntry condition. Then a new 4K memory is allocated for
Lv2 since 1G+2M is not 1G-aligned.
So when ParentPagingEntry is non-present, before allocate 4K memory
for next level paging, we also check if ParentPagingEntry Attribute&
Mask and input Attribute&Mask are the same.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Last commit changed the CpuPageTableLib API PageTableMap, unit
test code should also be modified.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The definition of IA32_MAP_ATTRIBUTE has 64 bits, and one of the bit
field PageTableBaseAddress is from bit 12 to bit 52. This means if the
compiler treats the 64bits value as two UINT32 value, the field
PageTableBaseAddress spans two UINT32 value. That's why when building in
NOOPT mode in IA32, the below issue is noticed:
unresolved external symbol __allshl
This patch fix the build failure by seperate field PageTableBaseAddress
into two fields, make sure no field spans two UINT32 value.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Modify RandomTest to check if parameter IsModified of
PageTableMap() correctlly indicates whether input page table
is modified or not.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Add OUTPUT IsModified parameter in PageTableMap() to indicate
if page table has been modified. With this parameter, caller
can know if need to call FlushTlb when the page table is in CR3.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Enable non-1:1 mapping in random test. In previous test, non-1:1
test will fail due to the non-1:1 mapping issue in CpuPageTableLib
and invalid Input Mask when creating new page table or mapping
not-present range. Now these issue have been fixed.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Modify RandomTest to check invalid input. When creating new page
table or updating exsiting page table:
1.If set [LinearAddress, LinearAddress+Length] to non-present, all
other attributes should not be provided.
2.If [LinearAddress, LinearAddress+Length] contain non-present range,
the Returnstatus of PageTableMap() should be InvalidParameter when:
2.1Some of attributes are not provided when mapping non-present range
to present.
2.2Set any other attribute without setting the non-present range to
Present.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Add LastMapEntry pointer to replace MapEntrys->Maps[MapsIndex]
in SingleMapEntryTest () of RandomTest.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Add an input parameter to control the probability of returning
true. Change RandomBoolean() in RandomTest from 50% chance
returning true to returning true with the percentage of input
Probability.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add manual test case to check input Mask and Attribute. The check
steps are:
1.Create Page table to cover [0, 2G]. All fields of MapMask should
be set.
2.Update Page table to set [2G - 8K,2G] from present to non-present.
All fields of MapMask except present should not be set.
3.Still set [2G - 8K, 2G] as not present, this case is permitted.
But set [2G - 8K, 2G] as RW is not permitted.
4.Update Page table to set [2G - 8K, 2G] as present and RW. All
fields of MapMask should be set.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
For different usage, check if the combination for Mask and
Attr is valid when creating or updating page table.
1.For non-present range
1.1Mask.Present is 0 but some other attributes is provided.
This case is invalid.
1.2Mask.Present is 1 and Attr.Present is 0. In this case,all
other attributes should not be provided.
1.3Mask.Present is 1 and Attr.Present is 1. In this case,all
attributes should be provided to intialize the attribute.
2.For present range
2.1Mask.Present is 1 and Attr.Present is 0.In this case, all
other attributes should not be provided.
All other usage for present range is permitted.
In the mentioned cases, 1.2 and 2.1 can be merged into 1 check.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
In function CreatePageTable(), add code to initialize MapMask to
MAX_UINT64. When creating new page table or map non-present range
to present, all attributes should be provided.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
When splitting leaf parent entry to smaller granularity, create
child page table before modifing parent entry. In previous code
logic, when splitting a leaf parent entry, parent entry will
point to a null 4k memory before child page table is created in
this 4k memory. When the page table to be modified is the page
table in CR3, if the executed CpuPageTableLib code is in the
range mapped by the modified leaf parent entry, then issue will
happen.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Clear PageSize bit(Bit7) for non-leaf entry in PageTableLibSetPnle.
This function is used to set non-leaf entry attributes so it should
make sure that the PageSize bit of the entry should be 0.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
In previous code logic, when splitting a leaf parent entry to
smaller granularity child page table, if the parent entry
Attribute&Mask(without PageTableBaseAddress field) is equal to the
input attribute&mask(without PageTableBaseAddress field), the split
process won't happen. This may lead to failure in non-1:1 mapping.
For example, there is a page table in which [0, 1G] is mapped(Lv4[0]
,Lv3[0,0], a non-leaf level4 entry and a leaf level3 entry). And we
want to remap [0, 2M] linear address range to [1G, 1G + 2M] with the
same attibute. The expected behaviour should be: split Lv3[0,0]
entry into 512 level2 entries and remap the first level2 entry to
cover [0, 2M]. But the split won't happen in previous code since
PageTableBaseAddress of input Attribute is not checked.
So, when checking if a leaf parent entry needs to be splitted, we
should also check if PageTableBaseAddress calculated by parent entry
is equal to the value caculated by input attribute.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Move some local variable initialization to the beginning of the
function. Also delete duplicated calculation for RegionLength.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add check for input Length in PageTableMap (). Return
RETURN_SUCCESS when input Length is 0.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Remove unneeded 'if' condition in CpuPageTableLib code.
The deleted code is in the code branch for present non-leaf parent
entry. So the 'if' check for (ParentPagingEntry->Pnle.Bits.Present
== 0) is always FALSE.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
For the case CPU logic index is 0, RSP points to the very top of all AP
stacks. That address is not mapped in page table.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Ted Kuo <ted.kuo@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Because UefiCpuPkg/UefiCpuLib is merged to MdePkg/CpuLib, remove the
dependency of UefiCpuLib.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
There are two libraries: MdePkg/CpuLib and UefiCpuPkg/UefiCpuLib. This
patch merges UefiCpuPkg/UefiCpuLib to MdePkg/CpuLib.
Change-Id: Ic26f4c2614ed6bd9840f817d50e47ac1de4bd013
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
RegisterCpuInterruptHandler did not allow setting
exception handlers for anything beyond the timer IRQ.
Beyond that, it didn't meet the spec around handling
of inputs.
RiscVSupervisorModeTrapHandler now will invoke
set handlers for both exceptions and interrupts.
Two arrays of handlers are maintained - one for exceptions
and one for interrupts.
For unhandled traps, RiscVSupervisorModeTrapHandler dumps
state using the now implemented DumpCpuContext.
For EFI_SYSTEM_CONTEXT_RISCV64, extend this with the trapped
PC address (SEPC), just like on AArch64 (ELR). This is
necessary for X86EmulatorPkg to work as it allows a trap
handler to return execution to a different place. Add
SSTATUS/STVAL as well, at least for debugging purposes. There
is no value in hiding this.
Fix nested exception handling. Handler code should not
be saving SIE (the value is saved in SSTATUS.SPIE) or
directly restored (that's done by SRET). Save and
restore the entire SSTATUS and STVAL, too.
Cc: Daniel Schaefer <git@danielschaefer.me>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Signed-off-by: Andrei Warkentin <andrei.warkentin@intel.com>
Rename AsmRelocateApLoopStart to AsmRelocateApLoopStartAmdSev
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the 'AsmRelocateApLoopStartGeneric' for X64 processors except 64-bit
AMD processors with SEV-ES.
Remove the unused arguments of AsmRelocateApLoopStartGeneric, updated
the stack offset.
Create PageTable for the allocated reserved memory.
Only keep 4GB limitation of memory allocation for the case APs still
need to be transferred to 32-bit mode before OS.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the union RELOCATE_AP_LOOP_ENTRY, split the path in RelocateApLoop
into two:
1. 64-bit AMD processors with SEV-ES
2. Intel processors (32-bit or 64-bit), 32-bit AMD processors, or
64-bit AMD processors without SEV-ES.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Check if AP_SAFE_STACK_SIZE is aligned with CPU_STACK_ALIGNMENT
during build time.
No functional or structural changes.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4337
This patch is to avoid configure SMBASE if SmBase relocation has been
done. If gSmmBaseHobGuid found, means SmBase info has been relocated
and recorded in the SmBase array. No need to do the relocation in
SmmCpuFeaturesInitializeProcessor().
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4076
Add the RISC-V instance of the TimerLib.
This is mostly copied from
edk2-platforms/Silicon/RISC-V/ProcessorPkg/Library/RiscVTimerLib
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Daniel Schaefer <git@danielschaefer.me>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4076
Add Cpu Exception Handler library for RISC-V. This is copied
from edk2-platforms/Silicon/RISC-V/ProcessorPkg/Library/RiscVExceptionLib
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Daniel Schaefer <git@danielschaefer.me>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Abner Chang <abner.chang@amd.com>
Reviewed-by: Andrei Warkentin <andrei.warkentin@intel.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
This reverts commit 73ccde8f6d since it
results in a hang of the IA32 processor and needs further clean-up.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=4234
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Commit 0426115b67 ("UefiCpuPkg: Remove unused API in
SmmCpuFeaturesLib.h", 2022-12-21) removed the declaration of the function
SmmCpuFeaturesAllocatePageTableMemory() from the "SmmCpuFeaturesLib.h"
library class header.
Remove the API's (null-)implementation from UefiCpuPkg/SmmCpuFeaturesLib
as well.
Build-tested with:
build -a IA32 -a X64 -b NOOPT -p UefiCpuPkg/UefiCpuPkg.dsc -t GCC5
Cc: Eric Dong <eric.dong@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=4235
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Dun Tan <dun.tan@intel.com>
During the finalization of Mp initialization before booting into the OS,
depending on whether Mwait is supported or not, AsmRelocateApLoop
places Aps in MWAIT-loop or HLT-loop.
Since paging is necessary for long mode, the original implementation of
moving APs to 32-bit was to disable paging to ensure that the booting
does not crash.
The current modification creates a page table in reserved memory,
avoiding switching modes and reclaiming memory by OS. This modification
is only for 64 bit mode.
More specifically, we keep the AMD logic as the original code flow,
extract and update the Intel-related code, where the APs would stay
in 64-bit, and run in a Mwait or Hlt loop until the OS wake them up.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
AsmRelocateApLoop is replicated for future Intel Logic Extraction,
further brings AP into 64-bit, and enables paging.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
APIs which are defined in CcExitLib.h are added with the CcExit prefix.
This is to make the APIs' name more meaningful.
This change impacts OvmfPkg/UefiCpuPkg.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
VmgExitLib once was designed to provide interfaces to support #VC handler
and issue VMGEXIT instruction. After TDVF (enable TDX feature in OVMF) is
introduced, this library is updated to support #VE as well. Now the name
of VmgExitLib cannot reflect what the lib does.
This patch renames VmgExitLib to CcExitLib (Cc means Confidential
Computing). This is a simple renaming and there is no logic changes.
After renaming all the VmgExitLib related codes are updated with
CcExitLib. These changes are in OvmfPkg/UefiCpuPkg/UefiPayloadPkg.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: James Lu <james.lu@intel.com>
Reviewed-by: Gua Guo <gua.guo@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
Remove the header files those are already included in
CpuFeatureLib.h.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
This change stripped away the code that can be
shared with other archs or vendors from Intel
implementation and put in to the common file,
leaves the Intel X86 implementation in the
IntelSmmCpuFeatureLib. Also updates the header
file and INF file.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ# 4093: Abstract SmmCpuFeaturesLib for sharing common code
Rename SmmCpuFeaturesLiCommon.c to
IntelSmmCpuFeaturesLib, because it was developed
specifically for Intel implementation. The code
that can be shared by other archs or vendors
will be stripped away and put in the common
file in the next patch.
Signed-off-by: Abner Chang <abner.chang@amd.com>
Cc: Abdul Lateef Attar <abdattar@amd.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Paul Grimes <paul.grimes@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Disable/Restore HpetTimer before and after running the Dxe
CpuExceptionHandlerLib unit test module. During the UnitTest, a
new Idt is initialized for the test. There is no handler for timer
intrrupt in this new idt. After the test module, HpetTimer does
not work any more since the comparator value register and main
counter value register for timer does not match. To fix this issue,
disable/restore HpetTimer before and after Unit Test if HpetTimer
driver has been dispatched. We don't need to send Apic Eoi in this
unit test module.When disabling timer, after RaiseTPL(), if there
is a pending timer interrupt, bit64 of Interrupt Request Register
(IRR) will be set to 1 to indicate there is a pending timer
interrupt. After RestoreTPL(), CPU will handle the pending
interrupt in IRR.Then TimerInterruptHandler calls SendApicEoi().
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
The previous change adds unit test for DxeCpuExeptionHandlerLib
in 64bit mode. This change create a PEIM to add unit test for
PeiCpuExceptionHandlerLib based on previous change.It can run
in both 32bit and 64bit modes.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Add target based unit tests for the DxeCpuExceptionHandlerLib.
A DXE driver is created to test DxeCpuExceptionHandlerLib.
Four test cases are created in this Unit Test module:
a.Test if exception handler can be registered/unregistered
for no error code exception.In the test case, only no error
code exception is triggered and tested by INTn instruction.
b.Test if exception handler can be registered/unregistered
for GP and PF. In the test case, GP exception is triggered
and tested by setting CR4_RESERVED_BIT to 1. PF exception
is triggered by writting to not-present or RO address.
c.Test if CpuContext is consistent before and after exception.
In this test case:
1.Set Cpu register to mExpectedContextInHandler before
exception. 2.Trigger exception specified by ExceptionType.
3.Store SystemContext in mActualContextInHandler and set
SystemContext to mExpectedContextAfterException in handler.
4.After return from exception, store Cpu registers in
mActualContextAfterException.
The expectation is:
1.Register values in mActualContextInHandler are the same
with register values in mExpectedContextInHandler.
2.Register values in mActualContextAfterException are the
same with register values mActualContextAfterException.
d.Test if stack overflow can be captured by CpuStackGuard
in both Bsp and AP. In this test case, stack overflow is
triggered by a funtion which calls itself continuously.
This test case triggers stack overflow in both BSP and AP.
All AP use same Idt with Bsp. The expectation is:
1. PF exception is triggered (leading to a DF if sepereated
stack is not prepared for PF) when Rsp<=StackBase+SIZE_4KB
since [StackBase, StackBase + SIZE_4KB] is marked as not
present in page table when PcdCpuStackGuard is TRUE.
2. Stack for PF/DF exception handler in both Bsp and AP is
succussfully switched by InitializeSeparateExceptionStacks.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Support PAE paging for PageTableParse API in CpuPageTableLib.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
The PEI instance of the CpuExceptionHandlerLib didn't implement the
RegisterCpuInterruptHandler() API. This patch adds the missing API.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
This commit is a code optimization to allow bigger seperate stack size in
ArchSetupExceptionStack. In previous code logic, CPU_STACK_ALIGNMENT bytes
will be wasted if StackTop is already CPU_STACK_ALIGNMENT aligned.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Abner Chang <abner.chang@amd.com>
To remove the dependency of CPU register, 4/8 byte at the top of the
stack is occupied for CpuMpData. BIST information is also taken care
here. This modification is only for PEI phase, since in DXE phase
CpuMpData is accessed via global variable.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
The API of InitializeSeparateExceptionStacks is just changed before, and
makes the struct CPU_EXCEPTION_INIT_DATA an internal definition.
Furthermore, we can even remove the struct to make core simpler.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
When switch bsp, old bsp and new bsp put CR0/CR4 into stack, and put IDT
and GDT register into a structure. After they exchange their stack, they
restore these registers. This logic is now implemented by assembly code.
This patch aims to reuse (Save/Restore)VolatileRegisters function to
replace such assembly code for better code readability.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3962
Two SMM variables (mSmrrSupported & mSmmFeatureControlSupported) are global
variables, they control whether the SMRR and SMM Feature Control MSR will
be restored respectively.
To avoid the TOCTOU, add PCD to control SMRR & SmmFeatureControl enable.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Currently, when waking up AP, IDT table of AP will be set in 16 bit code,
and assume the IDT table base is 32 bit. However, the IDT table is created
by BSP. Issue will happen if the BSP allocates memory above 4G for BSP's
IDT table. Moreover, even the IDT table location is below 4G, the handler
function inside the IDT table is 64 bit, and it won't take effect until
CPU transfers to 64 bit long mode. There is no benefit to set IDT table in
such an early phase.
To avoid such issue, this patch moves the LIDT instruction into 64 bit
code.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Add host based unit tests for the CpuPageTableLib services.
Unit test focuses on PageTableMap function, containing two kinds of test
cases: manual test case and random test case.
Manual test case creates some corner case to test function PageTableMap.
Random test case generates multiple random memory entries (with random
attribute) as the input of function PageTableMap to get the output
pagetable. Output pagetable will be validated and be parsed to get output
memory entries, and then the input and output memory entries will be
compared to verify the functionality.
The unit test is not perfect yet. There are options for random test, and
some of them control the test coverage, and some option are not ready.
Will enhance in the future.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
This reverts commit 2812668bfc for tag202208.
This feature will be merged after stable tag 202208 is created.
Signed-off-by: Liming Gao <gaoliming@byosoft.com.cn>
Reviewed-by: Zhiguang Liu <zhiguang.liu@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Add host based unit tests for the CpuPageTableLib services.
Unit test focuses on PageTableMap function, containing two kinds of test
cases: manual test case and random test case.
Manual test case creates some corner case to test function PageTableMap.
Random test case generates multiple random memory entries (with random
attribute) as the input of function PageTableMap to get the output
pagetable. Output pagetable will be validated and be parsed to get output
memory entries, and then the input and output memory entries will be
compared to verify the functionality.
The unit test is not perfect yet. There are options for random test, and
some of them control the test coverage, and some option are not ready.
Will enhance in the future.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The change doesn't change functionality behavior.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With following paging structure to map
[2M-4K, 2M] as P = 1, RW = 0,
[2M, 4M] as P = 1, RW = 1:
PML4[0] -> PDPTE[0] -> PDE[0](RW = 0) -> PTE[255](P = 0, RW = 0)
-> PDE[1](RW = 1)
When a new request to map [2M-4K, 2M+4K] as P = 1, RW = 1,
CpuPageTableMap() wrongly requests 4K buffer size for the new mapping
request.
But in fact, for [2M-4K, 2M] request, PTE[255] can be changed in place,
for [2M, 2M+4K], no change is needed because PDE[1].RW = 1 already.
The change fixes the bug.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With the following paging structure that maps [0, 2G] with ReadWrite
bit set.
PML4[0] --> PDPTE[0] --> PDE[0-255]
\-> PDPTE[1] --> PDE[0-255]
If ReadWrite bit is cleared in PML4[0] and PageTableMap() is called
to change [0, 2M] as read-only, today's logic unnecessarily changes
the paging structure in 2 aspects:
1. When setting PageTableBaseAddress in the entry, the code clears
all attributes.
2. Even the ReadWrite bit in parent entry is not set, the code clears
the ReadWrite bit in the leaf entry.
First change is wrong. It should not change other attributes when
setting the PA.
Second change is unnecessary. Because the parent entry already
declares the whole region as read-only, there is no need to clear
ReadWrite bit in the leaf entry again.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
With the following paging structure that maps [0, 2G] with ReadWrite
bit set.
PML4[0] --> PDPTE[0] --> PDE[0-255]
\-> PDPTE[1] --> PDE[0-255]
If ReadWrite bit is cleared in PML4[0] and PageTableMap() is called
to change [0, 2M] as writable, today's logic doesn't inherit the
parent entry's attributes when determining the child entry's
attributes. It just sets the PDPTE[0].PDE[0].ReadWrite bit.
But since the PML4[0].ReadWrite is 0, [0, 2M] is still read-only.
The change fixes the bug.
If the inheritable attributes in ParentPagingEntry conflicts with the
requested attributes, let the child entries take the parent attributes
and loosen the attribute in the parent entry.
E.g.: when PDPTE[0].ReadWrite = 0 but caller wants to map [0-2MB as
ReadWrite = 1 (PDE[0].ReadWrite = 1), we need to change
PDPTE[0].ReadWrite = 1 and let all PDE[0-255].ReadWrite = 0 first.
Then change PDE[0].ReadWrite = 1.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's logic wrongly treats the non-leaf entry as leaf entry and
updates its paging attributes.
The patch fixes the bug to only update paging attributes for
non-present entries or leaf entries.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When PageTableMap() is called to create non 1:1 mapping
such as [0, 1G) to [8K, 1G+8K), it should split the page entry to the
4K page level, but old logic has a bug that it just uses 1G page
entry.
The patch fixes the bug.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch replaces
LinearAddress + Offset == RegionStart
with
((LinearAddress + Offset) & RegionMask) == 0
The replace should not cause any behavior change.
Because:
1. In first loop of while when LinearAddress + Offset == RegionStart,
because the lower "BitStart" bits of RegionStart are all-zero,
all lower "BitStart" bits of (LinearAddress + Offset) are all-zero.
Because all lower "BitStart" bits of RegionMask is all-one and
bits are all-zero, ((LinearAddress + Offset) & RegionMask) == 0.
2. In following loops of the while, even RegionStart is increased
by RegionLength, the lower "BitStart" bits are still all-zero.
So the two expressions still semantically equal to each other.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When LinearAddress or Length is not aligned on 4KB, PageTableMap()
should return Invalid Parameter.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The lib includes two APIs:
* PageTableMap
It creates/updates mapping from LA to PA.
The implementation only supports paging structures used in 64bit
mode now. PAE paging structure support will be added in future.
* PageTableParse
It parses the page table and returns the mapping relations in an
array of IA32_MAP_ENTRY.
It passed some stress tests. These test code will be upstreamed in
other patches following edk2 Unit Test framework.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
CPU_EXCEPTION_INIT_DATA is now an internal implementation of
CpuExceptionHandlerLib. Union can be removed since Ia32 and X64 have the
same definition. Also, two fields (Revision and InitDefaultHandlers)are
useless, can be removed.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Since the API InitializeSeparateExceptionStacks is simplified and does't
use the struct CPU_EXCEPTION_INIT_DATA, CPU_EXCEPTION_INIT_DATA become
a inner implementation of CpuExcetionHandlerLib.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Jian J Wang <jian.j.wang@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Hide the Exception implementation details in CpuExcetionHandlerLib and
caller only need to provide buffer
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Currently, "push byte %[Vector]" causes nasm warning when Vector is larger
than 0x7F. This is because push accepts a signed value, and byte means
signed int8. Maximum signed int8 is 0x7F.
When Vector is larger the 0x7F, for example, when Vector is 255, byte 255
turns to -1, and causes the warning "signed byte value exceeds".
To avoid such warning, use dword instead of byte, this will increase 3 bytes
for each IdtVector.
For IA32, the size of IdtVector will increase from 10 bytes to 13 bytes.
For X64, the size of IdtVector will increase from 15 bytes to 18 bytes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Debkumar De <debkumar.de@intel.com>
Cc: Harry Han <harry.han@intel.com>
Cc: Catharine West <catharine.west@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The AP vector consists of 2 parts:
1. the initial 16-bit code that should be under 1MB and page aligned.
2. the 32-bit/64-bit code that can be anywhere in the memory with any
alignment.
The need of part #2 is because the memory under 1MB is temporary
"stolen" for use and will "give" back after all AP wake up. The range
of memory is not marked as code page in page table. CPU may trigger
exception as soon as NX is enabled.
The part #2 memory allocation can be done in the MpInitLibInitialize.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's implementation allocates below 1MB memory for the 16bit, 32bit
and 64bit code.
But it's not necessary since now the 32bit and 64bit code run at high
memory no matter in PEI and DXE phase.
The patch simplifies the logic to remove the code that handles the
case when WakeupBufferHigh is 0.
It also reduce the memory foot print under 1MB by allocating
memory for 16bit code only.
MP_CPU_EXCHANGE_INFO is still under 1MB which is immediate
after the 16bit code.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch does several simplifications:
1. Treat SwitchToRealProc as part of RendezvousFunnelProc.
So the common logic in MpLib.c doesn't need to be aware of
SwitchToRealProc.
As a result, SwitchToRealSize/Offset are removed from
MP_ASSEMBLY_ADDRESS_MAP.
2. Move SwitchToRealProc to AmdSev.nasm.
All other assembly code in AmdSev.nasm is called through
OneTimeCall.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
global in NASM file is used for symbols that are
referenced in C files.
Remove unneeded global keyword in NASM file.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's implementation assumes PEI phase runs at 32bit so
the execution-disable feature is not applicable.
It's not always TRUE.
The patch allocates 32bit&64bit code buffer for PEI phase as well.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today InitializeCpuExceptionHandlersEx is called from three modules:
1. DxeCore (links to DxeCpuExceptionHandlerLib)
DxeCore expects it initializes the IDT entries as well as
assigning separate stacks for #DF and #PF.
2. CpuMpPei (links to PeiCpuExceptionHandlerLib)
and CpuDxe (links to DxeCpuExceptionHandlerLib)
It's called for each thread for only assigning separate stacks for
#DF and #PF. The IDT entries initialization is skipped because
caller sets InitData->X64.InitDefaultHandlers to FALSE.
Additionally, SecPeiCpuExceptionHandlerLib, SmmCpuExceptionHandlerLib
also implement such API and the behavior of the API is simply to initialize
IDT entries only.
Because it mixes the IDT entries initialization and separate stacks
assignment for certain exception handlers together, in order to know
whether the function call only initializes IDT entries, or assigns stacks,
we need to check:
1. value of InitData->X64.InitDefaultHandlers
2. library instance
This patch cleans up the code to separate the stack assignment to a new API:
InitializeSeparateExceptionStacks().
Only when caller calls the new API, the separate stacks are assigned.
With this change, the SecPei and Smm instance can return unsupported which
gives caller a very clear status.
The old API InitializeCpuExceptionHandlersEx() is removed in this patch.
Because no platform module is consuming the old API, the impact is none.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
InitializeCpuExceptionHandlers() expects caller allocates IDT while
InitializeCpuInterruptHandlers() allocates 256 IDT entries itself.
InitializeCpuExceptionHandlers() fills max 32 IDT entries allocated
by caller. If caller allocates 10 entries, the API just fills 10 IDT
entries.
The inconsistency between the two APIs makes code hard to
unerstand and hard to share.
Because there is only one caller (CpuDxe) for
InitializeCpuInterruptHandler(), this patch updates CpuDxe driver
to allocates 256 IDT entries then call
InitializeCpuExceptionHandlers().
This is also a backward compatible change.
With this change, InitializeCpuInterruptHandlers() is removed
completely.
And InitializeCpuExceptionHandlers() fills max 32 entries for PEI
and SMM instance, max 256 entries for DXE instance.
Such behavior matches to the original one.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Additionally removed two useless global variables:
"SPIN_LOCK mDisplayMessageSpinLock" from SMM instance.
"UINTN mEnabledInterruptNum" from DXE instance.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Today the DXE instance allocates code page and then copies the IDT
vectors to the allocated code page. Then it fixes up the vector number
in the IDT vector.
But if we update the NASM file to generate 256 IDT vectors, there is
no need to do the copy and fix-up.
A side effect is 4096 bytes (HOOKAFTER_STUB_SIZE * 256) is used for
256 IDT vectors while 32 IDT vectors only require 512 bytes without
this change, in following library instances:
1. 32bit SecPeiCpuExceptionHandlerLib and PeiCpuExceptionHandlerLib
2. 64bit PeiCpuExceptionHandlerLib
But considering the code logic simplification, 3.5K extra space is
not a big deal.
If 3.5K is too much, we can enhance the code further to generate 32
vectors for above mentioned library instances.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Acked-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3918
This reverts commit 88da06ca76.
This commit triggers the ASSERT in Non-Td guest.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
There are two libraries: MdePkg/CpuLib and UefiCpuPkg/UefiCpuLib and
UefiCpuPkg/UefiCpuLib will be merged to MdePkg/CpuLib. To avoid build
failure, add CpuLib dependency to all modules that depend on UefiCpuLib.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3711
Per SDM, changing the mode of APIC timer (from one-shot to periodic or
vice versa) by writing to the timer LVT entry does not start the timer.
To start the timer, it is necessary to write to the initial-count
register.
If initial-count is wrote before mode change, it's possible that timer
expired before the mode change. Thus failing the periodic mode.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Julien Grall <julien@xen.org>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
RFC: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
In TDVF BSP and APs are simplified. BSP is the vCPU-0, while the others
are treated as APs.
So MP intialization is rather simple. ApWorker is not supported, BSP is
always the working processor, while the APs are just in a
wait-for-precedure state.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
RFC: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
MSR is accessed in BaseXApicX2ApicLib. In TDX some MSRs are accessed
directly from/to CPU. Some should be accessed via explicit requests
from the host VMM using TDCALL(TDG.VP.VMCALL). This is done by the
help of TdxLib.
Please refer to [TDX] Section 18.1
TDX: https://software.intel.com/content/dam/develop/external/us/en/
documents/tdx-module-1.0-public-spec-v0.931.pdf
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
RFC: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
Add base support to handle #VE exceptions. Update the common exception
handlers to invoke the VmTdExitHandleVe () function of the VmgExitLib
library when a #VE is encountered. A non-zero return code will propagate
to the targeted exception handler.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
RFC： https://bugzilla.tianocore.org/show_bug.cgi?id=3429
VmgExitLib performs the necessary processing to handle a #VC exception.
VmgExitLibNull is a NULL instance of VmgExitLib which provides a
default limited interface. In this commit VmgExitLibNull is extended to
handle a #VE exception with a default limited interface. A full feature
version of #VE handler will be created later.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
