mirror of
https://git.proxmox.com/git/mirror_ubuntu-kernels.git
synced 2025-12-04 13:39:43 +00:00
0171b07373
The microSD card detect pin is physically connected to the MPU pin PI3. The Device Tree configuration of the card detect pin was wrong—it was set to pin PB7 instead. If such configuration was used, the kernel would hang on “Waiting for root device” when booting from a microSD card. Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
81 lines
1.8 KiB
Plaintext
81 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
|
|
/*
|
|
* Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "stm32mp157c-odyssey-som.dtsi"
|
|
|
|
/ {
|
|
model = "Seeed Studio Odyssey-STM32MP157C Board";
|
|
compatible = "seeed,stm32mp157c-odyssey",
|
|
"seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
|
|
|
|
aliases {
|
|
ethernet0 = ðernet0;
|
|
serial0 = &uart4;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
status = "okay";
|
|
pinctrl-0 = <ðernet0_rgmii_pins_a>;
|
|
pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
|
|
pinctrl-names = "default", "sleep";
|
|
phy-mode = "rgmii-id";
|
|
max-speed = <1000>;
|
|
phy-handle = <&phy0>;
|
|
assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
|
|
assigned-clock-parents = <&rcc PLL4_P>;
|
|
assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
|
|
st,eth-clk-sel;
|
|
|
|
mdio0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "snps,dwmac-mdio";
|
|
phy0: ethernet-phy@7 { /* KSZ9031RN */
|
|
reg = <7>;
|
|
reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
|
|
reset-assert-us = <10000>;
|
|
reset-deassert-us = <300>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&i2c1_pins_a>;
|
|
pinctrl-1 = <&i2c1_sleep_pins_a>;
|
|
i2c-scl-rising-time-ns = <100>;
|
|
i2c-scl-falling-time-ns = <7>;
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&sdmmc1 {
|
|
pinctrl-names = "default", "opendrain", "sleep";
|
|
pinctrl-0 = <&sdmmc1_b4_pins_a>;
|
|
pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
|
|
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
|
|
cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
disable-wp;
|
|
st,neg-edge;
|
|
bus-width = <4>;
|
|
vmmc-supply = <&v3v3>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart4 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart4_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|