BSSID CAM is a kind of CAM that is used to determine if we receive a packet
or not. Add an entry to assist in debugging.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-6-pkshih@realtek.com
EDCCA signal can block transmitting in certain situation, so ignore this
signal and use others to decide transmitting time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-4-pkshih@realtek.com
Set proper setting according to RX quota, and then it doesn't break buffer
due to size of received packet exceeding buffer size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-3-pkshih@realtek.com
By experiments, it spends ~45/1090~2480us to enter/leave low power mode,
so the old polling interval 1000us can waste time. Use smaller polling
interval depends on experimental results to reduce the time to transition
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-5-pkshih@realtek.com
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
Initialize registers to default values, such as PTA and GNT pin, and set
pin MUX according to number of antenna on hardware module.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-10-pkshih@realtek.com
Disable watchdog timer to prevent it timeout suddenly.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-8-pkshih@realtek.com
The bit B_AX_SS_NONEMPTY_SS2FINFO_EN should be clear, because we configure
C-MAC as hardware TX/RX mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-6-pkshih@realtek.com
Turn on ERR IMR, and then firmware can capture interrupts reflecting
errors to recover hardware states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-5-pkshih@realtek.com
Similarly, create functions to set specific C-MAC masks for firmware
recovery.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-4-pkshih@realtek.com
These interrupts are used by firmware to recover hardware. Create
functions to set specific D-MAC masks to replace plain register settings.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-3-pkshih@realtek.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a dummy function for packet offload to eliminate warning message
"c2h class 1 func 2 not support". This c2h is for debug purpose and
its presence itself can do the work, so further parsing won't be
required for now.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-3-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.
Besides, a few uses of error status are refined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.
(no logic is changed)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
In order to support 8852C that uses 32 bits to control TX types.
This patch doesn't really use 32 bits tx_en yet, but next patch will
use it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-12-pkshih@realtek.com
Use if() style would be clear than "? :", because the else cases are
always 0. The read val from rtw89_mac_read_lte() isn't used, so remove
this statement.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-11-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
Initialize FW status and disabled H2C function if CPU disabled. Then, it
can reset to initial state.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-9-pkshih@realtek.com
8852C add new hardware feature -- preload window, which is used to load
more data to D-MAC, so it can possibly yield better performance.
This patch is to configure preload and reserved size for next window.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-8-pkshih@realtek.com
Modify functions that control D-MAC (data MAC) and LDO to support variant
chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-7-pkshih@realtek.com
DAV is an another efuse region that new chip, like 8852C, has this region.
Extend the code to read it, and convert the physical map to logical map
followed by original logical map.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-12-pkshih@realtek.com
The HCI_FUNC_EN address of 8852C is different from existing chipset, so
add a chip_info::hci_func_en_addr to fill the address individually.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-8-pkshih@realtek.com
New chipset uses individual power_{on/off} functions to replace old power
sequences, because it is hard to represent new complicated flow in a
sequence table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-7-pkshih@realtek.com
We found management frames get stuck when wifi chip
enters low ps mode. So we add one notify wake function
to trigger wifi chip into normal mode before forwarding
management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-3-pkshih@realtek.com
Declare this function allows us to use customized scanning policy, so
each scan takes less time. This is a similar implementation to hw_scan
in rtw88, except that we offload more items to firmware and extend the
maximum IE length. For backward compatibility, we fallback to sw_scan
when firmware does not support this feature.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-2-pkshih@realtek.com
B_AX_PLT_EN is to enable polluted mechanism. If it is enabled and
gnt_bt = 1 while wlan TX, B_AX_BT_PLT_PKT_CNT counter will increase,
but TX counter to BB will not. Without this bit BTCoex mechanism might
have some problems.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208082751.43553-1-pkshih@realtek.com
In AP mode, when a STA associate to us, we need to create an entry in
firmware and hardware, and then they can transmit data properly.
The entry index called mac_id which is assigned when sta_add, and we ask
firmware to create an entry for an associated station. Also, the address
CAM should be filled so hardware can know which packet is ours, and lookup
the mac_id for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-5-pkshih@realtek.com
Fill mac_id and self_role depends on the operation mode.
In AP mode, echo connected station has an unique mac_id, and each vif also
has one mac_id to represent itself.
The self_role is assigned to vif if the operation mode is decided, and
RTW89_SELF_ROLE_AP_CLIENT is assigned to the connected STA in AP mode,
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-2-pkshih@realtek.com
Call to dle_dfi_qempty might fail, leaving qempty.qempty untouched, which
is latter used to control the for loop. If that happens, it's not
initialized anywhere.
Initialize it so the loop doesn't iterate unless it's modified by the
call to dle_dfi_qempty.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220113094253.73370-1-ihuguet@redhat.com
HIQ is short for high queue that is used to send broadcast/multicast
packets right after TBTT in AP mode. Two registers, DTIM and window size,
are configured accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-10-pkshih@realtek.com
The H2C_FUNC_MAC_FWROLE_MAINTAIN also maintains the roles of all connected
stations; not just the role of VIF. So, I correct the name, but don't
change the logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-9-pkshih@realtek.com
The h2c_join firmware command is used to indicate a station is connected,
and the assoc_cmac_tbl firmware command is used to set CMAC table
corresponding to a mac_id. Both commands must work in both station and AP
modes. Use the mac_id of rtw89_sta naturally and intuitively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-8-pkshih@realtek.com
This C2H notify driver the beacon count we send out. We don't handle the
content for now, so add a dummy handler to avoid messages, like
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 3f 0f 00 00 00 80 0a 00 00 00 00 a0
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 40 0f 00 00 00 00 03 20 00 00 00 a5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-5-pkshih@realtek.com
We are planning to support more chipsets, e.g. 8852C. Before that, we
consider architecutre to handle multiple kinds of chipsets. Obviosuly,
based on original design, rtw89_core module will have large size even
if there is only one chipset under running. It is because all chipset
related things are put in rtw89_core now. To reduce such overhead, we
extract modules of rtw89 and adjust dependencies between modules.
The following assumes that 8852AE, 8852AU, and 8852CE are all supported,
we describe the difference before and after extraction.
[Before extraction]
-------------
|------------------------------------ | rtw89_usb |
V -------------
--------------------------------------- -------------
| rtw89_core (including 8852A, 8852C) | <--- | rtw89_pci |
--------------------------------------- -------------
The data of 8852A and 8852C are built in rtw89_core.
And rtw89_pci is the entry of 8852AE and 8852CE.
And rtw89_usb is the entry of 8852AU.
[After extraction]
------------- ----------------
|----------- | rtw89_usb | <-------- | rtw89_8852au |
| ------------- ----------------
V --------------- |
-------------- | | <---------------
| rtw89_core | <--- | rtw89_8852a |
-------------- | | <---------------
^ ^ --------------- |
| | ------------- ----------------
| | | | <-------- | rtw89_8852ae |
| |----------- | rtw89_pci | ----------------
| | | <-----------------
| ------------- |
| --------------- ----------------
|--------------- | rtw89_8852c | <------ | rtw89_8852ce |
--------------- ----------------
The data of 8852A/8852C is extracted to rtw89_8852a/rtw89_8852c.
And rtw89_pci/rtw89_usb handles only common flow of pci/usb bus.
Finally, 8852AE, 8852AU, and 8852CE have individual entry modules,
i.e. rtw89_8852ae, rtw89_8852au, and rtw89_8852ce correspondingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221025828.25092-1-pkshih@realtek.com
