clear the flag MT76_STATE_MCU_RUNNING immediately after reset to indicate
the MCU has already stopped working at the point. That is a preliminary
patch for the following patch to perform the register access in the
remaining reset handler using SDIO mailbox way instead of MCU command
because the RAM firmware is cleared out.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acquire the SDIO as needed as possible because either MT7663S or MT7921S
is a multiple-function device that always includes Bluetooth that would
share with the same SDIO bus. So not to avoid breaking Bluetooth pairing,
audio, and HID such kind of time critical application on that, we only
lock sdio bus when it is necessary in WiFi driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915_mcu_wtbl_generic_tlv, rely on vif->bss_conf.aid for
aid in sta mode and not on sta->aid.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mac80211.c:183:32:
warning: symbol 'mt76_sar_capa' was not declared. Should it be static?
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add pci_device_id to enable mt7916. Note that MT_HW_CHIPID is no
longer used for further chips, so drop it accordingly.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since mt7916 supports up to 544 wcid entries, wlan_idx_hi needs to be set
in order to support wcid index >= 256
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move key configuration code shared between mt7921 and mt7915 in
mt76-connac module and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_get_phy_mode and mt76_connac_get_he_phy_cap utility
routines in mt7915 driver and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_chan_bw in mt76-connac code and remove
duplicated code from mt7921 and mt7915 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_mcu_get_cipher in mt76-connac code and remove
duplicated code from mt7921 and mt7915 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on common code available in mt76-connac module and remove
mt7915_mcu_add_tlv/mt7915_mcu_add_nested_tlv in mt7915 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu_alloc_wtbl_req routine and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu_alloc_sta_req routine and remove
duplicated code.
Add MT76_CONNAC_LIB module dependency in mt7915 module
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, fix tag len error for sta_rec_wtbl, which
causes fw parsing error for the tags placed behind it.
Fixes: d0e274af2f ("mt76: mt76_connac: create mcu library")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update v2 offset. This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mt7916 can support up to 544 wcid entries.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update firmware initialization for mt7916.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RXQ of mt7916 are separated to MT_RXQ_MAIN_WA and MT_RXQ_MCU_WA,
so, add initialization and preftech setting for the queue MT_RXQ_MAIN_WA.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7916 add MT_RXQ_MAIN_WA to receive tx free event separately
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7915_reg_desc to differentiate chip generations.
This is an intermediate patch to introduce mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7915_mmio_probe() which will be used for the upcoming devices.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmHEgv4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt7jQf/W1J8lkaMw6mYnr+inmwKaP11VIk765Sf
4FXZl4xks5rs5zJOs61c/zInNIbu7QVsJzQLmM/bhTB1zoZMRo6ugXXrZ/LPMT1u
X0mul1rC+NLZLlgaimNXRZUXJ2tGUsYYhGoZLHbcILx7XF7/9WtE4h7tLviLdMYk
l42yjjP6s/I/zQHrLQdA9/puGl7g8CItbwaNZg6+PjgbS9NPGATrw9UZdOWjPcl4
JLMRHVgKtdlYL/U/IvsYg6o3Vbo0r+KEI2IMg5fOSpNwqbeQRIN4cZG4TDeRDqD/
k4/ZiFYlNdfVeWmZxHyqX6D3sroIquKglyah34fjzsJ2TbJC1zMvjw==
=VHFz
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a possible race enabling/disabling runtime-pm between
mt7921_pm_set() and mt7921_poll_rx() since mt7921_pm_wake_work()
always schedules rx-napi callback and it will trigger
mt7921_pm_power_save_work routine putting chip to in low-power state
during mt7921_pm_set processing.
Suggested-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: Deren Wu <deren.wu@mediatek.com>
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/0f3e075a2033dc05f09dab4059e5be8cbdccc239.1640094847.git.lorenzo@kernel.org
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During heavy loading throughtput test, the RX buffer (128)
would be exhausted and some RX pkts dropped randomly. Increase
buffer size from 128 to 512 (a safer length) to avoid tput degrade
or cmd-timeout problem.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the false positive suspend error that may occur on mt7921s
with enlarging mcu timeout value.
The reason why we have to enlarge mcu timeout from HZ / 3 to HZ is
we should consider the additional overhead caused by running
concurrently with btmtksdio (a MT7921 bluetooth SDIO driver) that
would compete for the same SDIO bus in process context to complete
the suspend procedure.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update pm->suspended usage to be consistent with mt7921e driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the possible resume failure due to mt76_connac_mcu_set_hif_suspend
timeout.
That is because clearing the flag pm->suspended too early opened up a race
window, where mt7921_poll_tx/rx scheduled a ps_work to put the device in
doze mode, that is unexpected for the device is being resumed from the
suspend state and would make the remaining MCU comamnds in resume handler
failed to execute.
Fixes: ffa1bf9742 ("mt76: mt7921: introduce PM support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
clear pm->suspended in mt7921_mac_reset_work to allow pm runtime
can be enabled after wifi reset in any circumstance.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on le16_add_cpu() in mt76_connac_mcu_add_nested_tlv routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
to_wcid_lo and to_wcid_hi are no longer used in mt7921/mcu.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mu-mimo and ofdma packet counters statistics.
The statistics are clear on read.
Reviewed-by: Money Wang <Money.Wang@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove duplicated mcu definitions in mt7915 mcu.h and reused connac
ones.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, rely on MCU_CMD macro and do not command
definitions directly
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to MCU_EXT_CMD, introduce MCU_CE_CMD for CE commands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to MCU_EXT_CMD, introduce MCU_UNI_CMD for unified commands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of MCU_FW_PREFIX bit since it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Align MCU_EXT and MCU_FW definitions between mt76_connac and mt7915
driver. This is a preliminary patch to reuse mt76_connac in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce MCU_EXT_CMD and MCU_EXT_QUERY macros in mt76_connac module.
This is a preliminary patch to reuse mt76_connac module in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TXS in mt7921 may be forwared to tx_done event. Should try to catch
TXS information in tx_done event as well.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of unsafe access since mt76_insert_ccmp_hdr moves the header.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move wiphy SAR capability configuration in mt76 module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
last_ch configuration must not be dependent on the current configured band
but it is defined by hw capabilities since the fw always expects the
following order:
- 2GHz
- 5GHz
- 6GHz
Fixes: 9b2ea8eee4 ("mt76: connac: set 6G phymode in single-sku support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Accroding to chip hw flow, mt7921s need to re-acquire privilege
again before normal running. Otherwise, the bus may be stuck in
an abnormal status.
Tested-by: Leon Yen <Leon.Yen@mediatek.com>
Co-developed-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set 6GHz cap to iftype data which is matched to the type of
current interface.
Fixes: 50ac15a511 ("mt76: mt7921: add 6GHz support")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
./drivers/net/wireless/mediatek/mt76/mt7921/sdio_mac.c: 223: 8-9: WARNING:
return of 0/1 in function 'mt7921s_tx_status_data' with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mtd_read() returns -EUCLEAN in case of corrected bit-flips.
As data was read, don't error out in this case.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Leave more time to abort transmissions (which could happen at low CCK rates)
Only warn if the last filter command is stuck
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the driver has configured the hardware to drop packets for a sta that was
in powersave mode, then clearing the flag too early opens up a small race
window during which packets could be dropped on wakeup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7915 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7603 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mask variable is assigned but not used after testmode disabled:
if (!en)
mask = phy->mt76->chainmask;
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to the MT7921S firmware, the cmd MCU_UNI_CMD_HIF_CTRL have to
be last MCU command to execute in suspend handler and all data traffic
have to be stopped before the cmd MCU_UNI_CMD_HIF_CTRL starts as well
in order that mt7921 can successfully fall into the deep sleep mode.
Where we reuse the flag MT76_STATE_SUSPEND and avoid creating
another global flag to stop all of the traffic onto the SDIO bus.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Reported-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch for the following patch
("mt76: mt7921s: fix the device cannot sleep deeply in suspend).
mt76_connac_mcu_set_hif_suspend eventually would be handled in each
bus-level suspend/resume handler in either mt7921/sdio.c or mt7921/pci.c
depending on what type of the bus the device is running on. We can move
mt76_connac_mcu_set_hif_suspend to bus-related files to simplify the logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt76x02 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_get_sar_power and mt76_init_sar_power in the common code.
This is a preliminary patch to add sar support to mt76x02 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check return code from mt76_connac_mcu_set_rate_txpower() in mt7921_config
routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
the wiphy's available antennas may be incorrect
When ext phy's antenna_mask is different from main phy
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
routine since mode is an u8 and PHY_MODE_AX_6G is set in phymode_ext
field in mt76_connac_bss_basic_tlv.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove always false if condition in get_omac_idx for sta type
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Even if it is not a real bug since mt76_connac_get_phy_mode runs just
for mt7921 where only STA is supported, fix a theoretical NULL pointer
dereference if new added modes do not support HE
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a possible NULL pointer deference issue in mt7921_mac_write_txwi
routine if vif is NULL.
Fixes: 33920b2bf0 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cap max offset value to ARRAY_SIZE(mt76_rates) - 1 in
mt76_calculate_default_rate routine in order to avoid possible Out Of
Bound accesses.
Fixes: 33920b2bf0 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce the basic configuration for BW160 capability in 7922
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix number of rx-queued frames reported by mt76_usb driver.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 2d8be76c16 ("mt76: debugfs: improve queue node readability")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only set RX_FLAG_RADIOTAP_HE and RX_FLAG_RADIOTAP_HE_MU from with their
own decoder functions to prevent header calculation error.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The HW can apply header translation to first fragmented frame, and
ramaining fragmented frame can only keep 802.11 format. Check and
reverse the first fragmented frame to 802.11 format to make sure
them can be defragmented by mac80211.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TGn fails sending SM power save mode action frame to the AP to switch
from dynamic SMPS mode to static mode.
Reported-by: Fang Zhao <fang.zhao@mediatek.com>
Signed-off-by: Fang Zhao <fang.zhao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the issue that some registers not configured properly after
restarting testmode.
(e.g. change state from idle to off, and off to idle)
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1 ("mt76: mt7921: refactor mcu.c to be bus independent")
Reported-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7615_register_ext_phy() outside the init_work().
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
offload_flags have to be dropped for mt7921 because mt76.omac_idx 0 would
always run as station mode that would cause Tx encapsulation setting
is not applied to mac80211.
Also, drop IEEE80211_OFFLOAD_ENCAP_4ADDR too because it is not really
being supported.
Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning removing mt7915_mcu_set_fixed_rate
since it is no longer used:
warning: symbol 'mt7915_mcu_set_fixed_rate' was not declared.
Should it be static?
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The code that uses variable queued has been removed,
and "mt76_is_usb(dev) ? q->ndesc - q->queued : q->queued"
didn't do anything, so all they should be removed as well.
Eliminate the following clang warnings:
drivers/net/wireless/mediatek/mt76/debugfs.c:77:9: warning: variable
‘queued’ set but not used.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 2d8be76c16 ("mt76: debugfs: improve queue node readability")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After mt7921s got added, there are two possible build problems:
a) mt7921s does not get built at all if mt7921e is not also enabled
b) there is a link error when mt7921e is a loadable module, but mt7921s
configured as built-in:
ERROR: modpost: "mt7921_mac_sta_add" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_sta_assoc" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_sta_remove" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_write_txwi" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_drv_pmctrl" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_fill_message" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_parse_response" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_ops" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_queue_rx_skb" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_update_channel" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
Fix both by making sure that Kbuild enters the subdirectory when
either one is enabled.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211204173848.873293-3-arnd@kernel.org
Fix pointer overwrite in mt7921s_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines since in
commit '2a9e9857473b ("mt76: fix possible pktid leak")
mt76_tx_status_skb_add() has been moved out of
mt7921s_write_txwi()/mt7663_usb_sdio_write_txwi() overwriting
hw key pointer in ieee80211_tx_info structure. Fix the issue saving
key pointer before running mt76_tx_status_skb_add().
Fixes: 2a9e985747 ("mt76: fix possible pktid leak")
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/eba40c84b6d114f618e2ae486cc6d0f2e9272cf9.1638193069.git.lorenzo@kernel.org
It's easier to use and understand, and to extend for EHT later,
if we use the values here instead of the shifted values.
Unfortunately, we need to add _POS so that we can use it in
places like iwlwifi/mvm where constants are needed.
While at it, fix the typo ("NOMIMAL") which also helps catch any
conflicts.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20211126104817.7c29a05b8eb5.I2ca9faf06e177e3035bec91e2ae53c2f91d41774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Repalce kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is stored on a MTD partition print an error message
when reading this MTD partition failed. This is currently happening
often in OpenWrt because the initial data was written with using a flash
driver which ignores the error detection data and now OpenWrt uses a
driver which checks it.
With this patch a better error message is shown:
[ 8.986988] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
[ 9.100508] mt7915e 0000:01:00.0: reading EEPROM from mtd factory failed: -117
[ 9.144289] mt7915e: probe of 0000:01:00.0 failed with error -22
mt7915 does not work without an EEPROM, MT7922 still works.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add debugfs knobs to read MCU utilization, which helps user know
firmware status more easily to narrow down CPU bottleneck issues.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, driver can support single rate, (HE)GI and HE_LTF
configuration through .set_bitrate_mask().
Tested-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make mt7915_mcu_sta_he_tlv() as a part of mt7915_mcu_add_rate_ctrl() as
firmware rate control should get HE rate information from sta_rec_he,
and reduce a global function accordingly.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Band0 and band1 share the same hardware, so band0 will stop Tx/Rx when
band1 performs Rx calibration. cal_cache is introduced to solve such
corner cases by moving necessary datas from channel_switch to bootup.
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
commit 7f4b792031 ("mt76: mt7615: add ibss support") introduced IBSS
and commit f4ec7fdf7f ("mt76: mt7615: enable support for mesh")
meshpoint support.
Both used in the "get_omac_idx"-function:
if (~mask & BIT(HW_BSSID_0))
return HW_BSSID_0;
With commit d8d59f66d1 ("mt76: mt7615: support 16 interfaces") the
ibss and meshpoint mode should "prefer hw bssid slot 1-3". However,
with that change the ibss or meshpoint mode will not send any beacon on
the mt7622 wifi anymore. Devices were still able to exchange data but
only if a bssid already existed. Two mt7622 devices will never be able
to communicate.
This commits reverts the preferation of slot 1-3 for ibss and
meshpoint. Only NL80211_IFTYPE_STATION will still prefer slot 1-3.
Tested on Banana Pi R64.
Fixes: d8d59f66d1 ("mt76: mt7615: support 16 interfaces")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007225725.2615-1-vincent@systemli.org
ARRAY_SIZE() is of type size_t, so the format specfier should
be %zu instead of %lu.
Fixes this build warning:
../drivers/net/wireless/mediatek/mt76/mt7921/main.c: In function ‘mt7921_get_et_stats’:
../drivers/net/wireless/mediatek/mt76/mt7921/main.c:1024:26: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘unsigned int’ [-Wformat=]
dev_err(dev->mt76.dev, "ei: %d SSTATS_LEN: %lu",
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: linux-wireless@vger.kernel.org
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022233251.29987-1-rdunlap@infradead.org
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Re-order and modify conditions for MU DL/UL and ofdma DL fields, and
also clean up some unnecessary zero settings.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, add per-vif tx counters in ethtool.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, add tx/rx statistics reporting through ethtool.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since it can run in parallel with mac_work, hold mutex lock in
mt7915_get_et_stats. Moreover update mib counters running
mt7915_get_et_stats.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Appears to have incorrectly offset 0x120 + 0x12 instead of 12 decimal,
leading to bogus power values being used.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce wifi chip reset support for mt7921 device to recover
mcu hangs or abnormal wifi system.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7921s 802.11ax (Wi-Fi 6) 2x2:2SS chipset.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mcu_get_nic_capability to obtain tx resource for SDIO device,
MAC address, and PHY capability.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend sdio module to support CONNAC2 hw that mt7921s rely on.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use physical address to unify the register access and reorder the
entries in fixed_map table to accelerate the address lookup for
MT7921e. Cosmetics the patch with adding an extra space to make all
entries in the array style consistent.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The longer event such as the event for mcu_get_nic_capability would hold
the data in paged fragment skb for the SDIO device so we turn the skb to
be linearized skb before accessing it to reuse the same event parser
betweem mt7921s and mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
rely on mcu reg access utility and drop the duplicated code.
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu reg access shared between mt7663s and mt7921s in mt76_connac_lib
module.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
MT7921_COMMON module grouping bus independent objects the both mt7921e and
mt7921s can share with and have to rely on.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add MU EDCA MCU command support to update MU AC parameter record field
from the access point.
Co-developed-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Tested-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove some more not used code in mt7915 debugfs.
Squash mt7915_puts_rate_txpower and mt7915_rate_txpower_show.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve xmit-queue debugfs node readability for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a dedicated mt76 debugfs sub-dir for ext-phy in dbdc mode.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set muru platform type by mcu cmd to notify fw to init corresponding
algorithm.
Suggested-by: Money Wang <money.wang@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The VTA (Valid for Txd Arrival time) bit should be set in tx descriptor,
which is necessary for WM fw to schedule SPL (station priority list)
normally before generating txcmd.
If it's not set, some unexpected wcids may be involved in SPL.
Suggested-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For broadcast/multicast wcid, the muar_idx should be 0xe.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework starec tags to the order which firmware expected. This also fixes
some weird behaviors during generating SPL of HE-MU.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix tag len error for sta_rec_wtbl, which causes fw parsing error for
the tags placed behind it.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch we can append txbf starec TLVs. This is an intermediate
patch to improve HE MUMIMO performances.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Beacon elements might be changed by hostapd configuraion, so driver
should compare both IEs and PHY capabilities to get the least common
denominator before association.
Co-developed-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When received frame is decryped by hardware, CCMP PN is checked by
mt76.
When management frame protection (IEEE 802.11w) is used, we must use
a separate counter for tracking received CCMP packet number for the
management frames. The previously used counter was shared with data
frames and that can cause problems in detecting replays incorrectly
for robust management frames.
Add a new counter just for robust management frames to avoid this
issue.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a delay parameter for firmware to support delay scheduled scan.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce twt_stats knob in debugfs in order to dump established
agreements
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable TWT support in AP mode
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce individual TWT support to mt7915 in AP mode.
Implement the two following mac80211 callbacks:
- add_twt_setup
- twt_teardown_request
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to add TWT support to mt7915
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce an unlocked verion of mt7915_get_tsf routine.
This is a preliminary patch to add TWT support to mt7915.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Each firmware piece with mt7915 and mt7921 do not have the MCU header to
reroute the packet to the internal RAM. So we do not need to consider the
MCU header size in __mt76_mcu_send_firmware.
Move the MCU header overhead calculation to mt76_mcu_send_firmware (for
older chipsets)
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 1c099ab447 ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce __mt76_mcu_send_firmware routine to specify mcu message max
length. This is a preliminary patch to support mt7921s driver.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some platforms boot from SD card and don't come with calibration data
stored anywhere on the board.
As EEPROM data is rather small it can be embedded into the device tree
to be loaded from there by the mt76.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce MT_TX_STATUS_SKB_TIMEOUT to 250ms
Tested-by: mrkiko.rs@gmail.com
Co-developed-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Substitute sk_buff_head status_list with spinlock_t status_lock since we
just need it for locking
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unlock 6GHz band if supported by the device. Configure HE 6G
capabilities.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce 6GHz channel list in mt76 module. This is a preliminary patch
to unlock 6GHz band for mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to enable 6GHz band for mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to enable 6GHz band for mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce sta_rec_he_6g_capa tlv in order configure the mcu with 6GHz
capabilities. This is a preliminary patch to enable 6GHz band for
mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure tx rate power for 6GHz channels. This is a preliminary patch
to enable 6GHz band for mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure 6GHz channels defining mcu channel domain. This is a
preliminary patch to enable 6GHz band on mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to support 6GHz band on mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to support 6GHz band on mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds the new mib counters from last patch into ethtool
stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add register definitions and read & accumulate them in
the mib polling logic. Note that some registers should not
be read since firmware is already reading them. If driver
reads those, they will be cleared-on-read, and so the firmware
stats will be incorrect.
For these 'do-not-read' stats, add them to the registers definition
so that other developers can be aware of these constraints, but do
not actually read them in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These counters are clear-on-read, so we need to accumulate
them in the update_stats poll logic, and read the accumulated
values instead of directly doing register reads when reporting
to debugfs and ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The tx status callback is not called for every frame, so
those specific counters under-count, but at least they give
some idea of what is going on.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add tx-mode (ofdma, ht, vht, HE) histogram,
tx-ru-idx histogram, and tx-bandwidth histogram.
Also add tx attempts and tx success counters.
All of this is per-station.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This exposes some tx-path stats to the ethtool API, so that
ethtool -S wlanX provides some more useful info.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We should pass the error code to the caller immediately
to avoid the possible infinite retry to release the semaphore.
Fixes: 1c099ab447 ("mt76: mt7921: add MCU support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robustify hardware initialization in the current driver probing flow
to get rid of the device is possibly lost after the machine boot due
to possible firmware abnormal state by trying to recover the failure
with more chances.
Tested-by: Leon Yen <Leon.Yen@mediatek.com>
Tested-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible infinite loop in mt7915_load_patch if
mt7915_mcu_patch_sem_ctrl always returns an error.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check all possible errors returned in mt7915_mcu_init routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
as you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Xingbang Liu <liu.airalert@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused tx rate reporting through mcu tx done event since
now tx status is fully supported
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report tx rate from tx status packets instead of receiving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce infrastructure support for tx status reporting
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915, introduce mt7921_txwi_free to report tx rate to
mac80211. This is a preliminary patch to add proper tx status report.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7615 is garbled.
Fixes: 109e505ad9 ("mt76: mt7615: add thermal sensor device support")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7915 is garbled. It appears that the hwmon logic does not make a
copy of the incoming string, but instead just copies a char* and expects
it to never go away.
Fixes: 33fe9c639c ("mt76: mt7915: add thermal sensor device support")
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Give a proper boottime_ns value for netlink RX to avoid scan
issues with Android.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
./drivers/net/wireless/mediatek/mt76/mt7615/usb_sdio.c:172:8-9:WARNING:
return of 0/1 in function 'mt7663_usb_sdio_tx_status_data' with return
type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7921 mac work can be idle for a long time due to runtime-pm so
update mib counters dumping phy stats
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing device wakeup in debugfs code if we are accessing chip
registers.
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As for 7915 moving mt7921_queue_rx_skb makes it possible to make
some functions in mac.c static
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WMM index range needs to be split between both PHYs if a second PHY exists.
The condition for that was accidentally written as checking if the vif PHY
is the secondary one
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Even if it is a not real issue, add missing brackets in
mt7915_mcu_sta_bfer_ht routine in order to improve code readability
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize brightness_set and blink_set callbacks to enable LED support.
The base 0x7c000000 is MCU space so driver can't touch it, and should
map the LED base to 0x18000000 host's view.
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At 160, this chip can only do 2x2 NSS. Fix the features
accordingly, verified it shows up properly in iw phy foo info
now.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop MT_DRV_AMSDU_OFFLOAD after introducing IEEE80211_OFFLOAD_ENCAP_ENABLED
flag in mac80211. Driver now checks vif->offload_flags to know encap offload
status of each interface.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1. EIFS has been divided into OFDM/CCK fields after 11ax generation.
2. For 5G/6G SIFS setting, hardware counts extra 6us for OFDM.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to the firmware usage, OFDM rates should fill out bit 6 - 13
while CCK rates should fill out bit 0 - 3 in legacy field of RA info to
make the rate adaption runs propertly. Otherwise, a unicast frame might be
picking up the unsupported rate to send out.
Fixes: 1c099ab447 ("mt76: mt7921: add MCU support")
Reported-by: Joshua Emele <jemele@chromium.org>
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report HE MU/BF radiotap.
That fixed HE MU packets dropped by mac80211 because they are missing the
ieee80211_radiotap_he_mu header.
Fixes: 163f4d22c1 ("mt76: mt7921: add MAC support")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Co-developed-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Tested-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mcu_set_p2p_oppps routine in mt76_connac_lib module in order
to be reused in mt7921 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Fixes: de5ff3c9d1 ("mt76: mt7615: introduce pm_power_save delayed work")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7921_mcu_set_beacon_filter utility routine in order to
remove duplicated code for hw beacon filtering.
Move mt7921_pm_interface_iter in debugfs since it is just used there.
Make the following routine static:
- mt7921_pm_interface_iter
- mt7921_mcu_uni_bss_bcnft
- mt7921_mcu_set_bss_pm
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt7921_mac_set_beacon_filter routine since it is no longer used.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove monitor_vif pointer from mt7921 since it is just a leftover of
initial porting.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Consider .max_reg_power in struct ieee80211_channel to limit the
maximum power the wireless device allowed to transmit on the
corresponding channel according to the regulatory domain.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update the proper firmware programming sequence to fix GTK rekey
offload failure on WPA mixed mode.
In the mt76_connac_mcu_key_iter,
gtk_tlv->proto should be only set up on pairwise key
and gtk_tlk->group_cipher should be only set up on the group key.
Otherwise, those parameters required by firmware would be set
incorrectly to cause GTK rekey offload failure on WPA mixed mode
and then disconnection follows.
Fixes: b47e21e75c ("mt76: mt7615: add gtk rekey offload support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Leon Yen <Leon.Yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The dma would be broken after rmmod flow. There are two different
cases causing this issue.
1. dma access without privilege.
2. hw access sequence borken by another context.
This patch handle both cases to avoid hw crash.
Fixes: 2b9ea5a8cf ("mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mesh and ad-hoc interfaces allow users to set mcast rate through
NL80211_ATTR_MCAST_RATE, so rework mt76_default_basic_rate() to
adapt that.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The bit fields of tx rate idx should be 6 bits, otherwise it might be
incorrect in HT mode.
For VHT/HE rates, only 4 bits are actually used by rate idx, the other
2 bits are used for other functions.
Fixes: c31d94af18 ("mt76: mt7915: fix tx rate related fields in tx descriptor")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch proper tx arbiter mode during testmode tx to prevent from
entering the flow of normal tx in FW.
Also, testmode SU and MU tx need to use different arbiter mode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If total eeprom size is divisible by per-page size, the i in for loop
will exceed max page index, which happens in our newer chipset.
Fixes: 26f18380e6 ("mt76: mt7915: add support for flash mode")
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware rate control may choose the high rate for EAPOL frames,
so checking IEEE80211_TX_CTL_USE_MINRATE to use the lowest TX rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware rate control may choose the high rate for EAPOL frames,
so checking IEEE80211_TX_CTL_USE_MINRATE to use the lowest TX rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, users can set the trigger/restore temperature for
thermal service according to their use cases.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add new chip mt7922 in mt7921 module with following items
1. new chip ID / fw bin name
2. is_mt7922()
check chip type for different fw files
3. mt7921_get_data_mode()
check security type of fw (backward compatible)
Co-developed-by: Jimmy Hu <Jimmy.Hu@mediatek.com>
Signed-off-by: Jimmy Hu <Jimmy.Hu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The acceptable event report should inlcude original CMD-ID. Otherwise,
drop unexpected result from fw.
Fixes: 1c099ab447 ("mt76: mt7921: add MCU support")
Signed-off-by: Jimmy Hu <Jimmy.Hu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
