MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The original single LDPC cap bit cannot be used to
differentiate LDPC cap in each PHY mode.
This modification split the single bit into 3 bits,
ht_ldpc, vht_ldpc, and he_ldpc.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Suggested-by: Money Wang <Money.Wang@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7663u_mcu_power_on utility routine since the code is shared
between mt7663u_mcu_init() and mt7663u_probe().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check return value of mt7615_mcu_restart routine in mt7663u_mcu_init().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The following error is see from the compiler:
mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’:
mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
The issue is due to allocating a buffer as string storage.
Fix by converting to a dynamical allocation of the buffer.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not always copy ethernet header in mt{7615,7915,7921}_reverse_frag0_hdr_trans
and use a pointer instead.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The radar detctor is used for dfs channel. So it will start after switching
to dfs channel and will stop after leaving. The TX will be blocked if radar
detctor isn't stopped in non-dfs channel.
This patch resets the dfs state to indicate the radar detector needs to be
stopped.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check sta_rates pointer value in mt7615_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing mt76_connac_pm_dequeue_skbs routine waking up mt7663s device
from runtime-pm sleep state.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a possible race in mt7615_pm_power_save_work() if rx/tx napi
schedules ps_work and we are currently accessing device register
on a different cpu.
Fixes: db928f1ab9 ("mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, process txfree and txstatus without allocating
skbs in order to reduce pressure on the memory allocator
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In some cases, the WA firmware needs to know if encryption is used, in order
to set the protection bit of packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7921 driver, fix a possible race enabling/disabling
runtime-pm between mt7615_pm_set() and mt7615_poll_rx().
mt7615_pm_wake_work() always schedules rx-napi callback and it will
trigger mt7615_pm_power_save_work routine putting the chip in low-power
state even if we are disabling runtime-pm deferring the actual chip wake
at the next access.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_mcu_rdd_cmd routine in mt76-connac module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_mcu_gen_dl_mode utility routine in mt76_connac_mcu.h
since it is shared by all drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_mcu_set_pm utility routine in connac module since it is
shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce is_connac_v1 inline utility routine to check if the device is
generation v1.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_connac_mcu_wtbl_update_hdr_trans routine in mt76-connac module
since it is shared between mt7915 and mt7615 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu_wtbl_ht_tlv routine and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu_sta_ba routine in mt7915 and remove duplicated
code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mcu_bss_basic_tlv/mt7915_mcu_bss_basic_tlv in connac
module since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7915_mcu_bss_ext_tlv/mt7615_mcu_bss_ext_tlv in connac module
since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7915_mcu_bss_omac_tlv/mt7615_mcu_bss_omac_tlv in connac module
since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acquire the SDIO as needed as possible because either MT7663S or MT7921S
is a multiple-function device that always includes Bluetooth that would
share with the same SDIO bus. So not to avoid breaking Bluetooth pairing,
audio, and HID such kind of time critical application on that, we only
lock sdio bus when it is necessary in WiFi driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove duplicated mcu definitions in mt7915 mcu.h and reused connac
ones.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, rely on MCU_CMD macro and do not command
definitions directly
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to MCU_EXT_CMD, introduce MCU_CE_CMD for CE commands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to MCU_EXT_CMD, introduce MCU_UNI_CMD for unified commands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Align MCU_EXT and MCU_FW definitions between mt76_connac and mt7915
driver. This is a preliminary patch to reuse mt76_connac in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce MCU_EXT_CMD and MCU_EXT_QUERY macros in mt76_connac module.
This is a preliminary patch to reuse mt76_connac module in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mask variable is assigned but not used after testmode disabled:
if (!en)
mask = phy->mt76->chainmask;
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
