The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control
as 1/16th of a line. This is what the sensor expects, but isn't very
intuitive. Switch the control to be in units of a line and simply do the
16x multiplication before passing the value to the sensor.
The datasheet for this sensor gives minimum exposure as 2 lines, so take
the opportunity to correct the lower bounds of the control.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure limits depend on the total height; when vblank is altered (and
thus the total height is altered), change the exposure limits to reflect
the new cap.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HTS values for some of the modes in the ov8865 driver are a bit
unusual, coming in lower than the output_size_x is set to. It seems
like they might be calculated to fit the desired framerate into a
configuration with just two data lanes. To bring this more in line
with expected behaviour, raise the HTS values above the output_size_x.
The corollary of that change is that the hardcoded frame intervals
against the modes no longer make sense, so remove those entirely.
Update the .g/s_frame_interval() callbacks to calculate the frame
interval based on the current mode and the vblank and hblank settings.
The implementation of the .enum_frame_interval() callback is no longer
suitable since the possible frame rate is now a continuous range depending
on the vblank control setting, so remove that callback entirely.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only
with timing control intended to be done via vblanking alone.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_VBLANK control to the ov8865 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_CID_GAIN control for this driver configures registers that
the datasheet specifies as analogue gain. Switch the control's ID
to V4L2_CID_ANALOGUE_GAIN.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver's v4l2_subdev_pad_ops currently does not include
.get_selection() - add support for that callback.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver as written expects a 24MHz input clock, but the sensor
is sometimes found on x86 platforms with a 19.2MHz input clock supplied.
Add a set of PLL configurations to the driver to support that rate too.
As ACPI doesn't auto-configure the clock rate, check for a clock-frequency
during probe and set that rate if one is found.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver is one of those that can be connected to a CIO2
device by the cio2-bridge code. This means that the absence of an
endpoint for this device is not necessarily fatal, as one might be
built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no
endpoint is found rather than a fatal error.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL configuration defined here sets 72MHz (which is correct), not
80MHz. Correct the comment.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI.
Add an ACPI match table to the driver so that it's probed on those
platforms.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5693 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2. The
chip is capable of a single lane configuration, but currently only two
lanes are supported.
Most of the sensor's features are supported, with the main exception
being the lens correction algorithm.
The driver provides all mandatory, optional and recommended V4L2 controls
for maximum compatibility with libcamera.
[mchehab: fixed a coding style warning]
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Current driver supports only SRGGB 10 bit RAW bayer format.
Add the enum_mbus_code implementation to report this format supported.
# v4l2-ctl -d /dev/v4l-subdev3 --list-subdev-mbus-codes
ioctl: VIDIOC_SUBDEV_ENUM_MBUS_CODE (pad=0)
0x300f: MEDIA_BUS_FMT_SRGGB10_1X10
#
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 has not explicitly declared a dependency upon VIDEO_V4L2.
While this dependency has likely always been met by configurations
including it, the device does use V4L2 core, and should depend upon it.
Add VIDEO_V4L2 as a dependency to match other drivers and prevent
failures when compile testing.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those are aliases for another function and not used at the
current implementation. So, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those functions just call a V4L2 core macro, and aren't used
anywhere. Get rid of them, in order to avoid clang warnings with
W=1.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Solve some clang warnings about unused functions by dropping
some time-conversion inline funcs that aren't used anywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar to other drivers, this should fix a Clang compilar warning when
building without CONFIG_OF in which case of_match_ptr() is NULL and
the const struct we would use otherwise is unused.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Include the more portable property.h instead of the OF specific of_graph.h
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When dw9768 working with ACPI systems, the dw9768 was turned
by i2c-core during probe, driver need activate the PM runtime
and ask runtime PM to turn off the device.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
show() should not use snprintf() when formatting the value to be
returned to user space.
Fix the following coccicheck warning:
drivers/media/i2c/ccs/ccs-core.c:3761: WARNING: use scnprintf or sprintf.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611.
Also: print chip names in upper case.
Fix an error message claiming that no ADV761x has been found,
while in reality a chip different than requested (though still
supported) may have been found.
Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TDA1997x (HDMI receiver) driver currently uses a specific video
format detection scheme. The frame (or field in interlaced mode), line
and HSync pulse durations are compared to those of known, standard video
modes. If a match is found, the mode is assumed to be detected,
otherwise -ERANGE is returned (then possibly ignored). This means that:
- another mode with similar timings will be detected incorrectly
(e.g. 2x faster clock and lines twice as long)
- non-standard modes will not work.
This patch replaces this scheme with a direct read of geometry
registers. This way all modes recognized by the chip are supported.
In interlaced modes, the code assumes the V sync signal has the same
duration for both fields. While this may be not necessarily true,
I can't see any way to get the "other" V sync width. This is most
probably harmless.
All tests have been performed on Gateworks' Ventana GW54xx board, with
a TDA19971 chip.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I came across a link failure from randconfig builds:
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove':
tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe':
tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev'
These clearly lack a 'select' statement, but I don't know why
this started happening only now. I had a bit of a look around to find
other configs that have the same problem, but could not come up with
a reliable way and found nothing else through experimentation.
It is likely that other symbols like these exist that need an extra
select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IR receiver has two issues:
- Sometimes there is no response to a button press
- Sometimes a button press is repeated when it should not have been
Hanging the polling interval fixes this behaviour.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=994050
Cc: stable@vger.kernel.org
Suggested-by: Joaquín Alberto Calderón Pozo <kini_calderon@hotmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the build errors reported by the kernel test robot by
selecting V4L2_ASYNC:
mips-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x1ec): undefined reference to `v4l2_async_unregister_subdev'
mips-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0x404): undefined reference to `v4l2_async_register_subdev'
Fixes: ed29f89497 ("media: i2c: ths8200: support asynchronous probing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MLX90640 should ideally be working without a frame skip.
In short, if a frame is skipped, then half of a frame loses correction
information, having no way to retrieve its original compensation.
This patch improves the timing in three ways:
1) Replaced schedule_timeout_interruptible() to usleep_range()
The former "only ensures that it will sleep for at least
schedule_delay (if not interrupted)", as pointed out by mchehab.
As a result, the frame rate could lag behind than the actual capability
of the hardware
(Raspberry Pi would show a few Hz slower than set value)
2) Calculation based on us, not jiffies
Jiffies usually has resolution of 100Hz, and possibly even cruder.
MLX90640 can go up to 64Hz frame rate, which does not make sense to
calculate the interval with aforementioned resolution.
3) Interval calculation based on the last frame's end time
Using the start time of the current frame will probably make tiny bit
of drift every time. This made more sense when I didn't realize 1),
but it still makes sense without adding virtually any complexity,
so this stays in.
Signed-off-by: Seongyong Park <euphoriccatface@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Static analysis reports this representative problem
tda1997x.c:1939: warning: 7th function call argument is an uninitialized
value
The 7th argument is buffer[0], which is set in the earlier call to
io_readn(). When io_readn() call to io_read() fails with the first
read, buffer[0] is not set and 0 is returned and stored in len.
The later call to hdmi_infoframe_unpack()'s size parameter is the
static size of buffer, always 40, so a short read is not caught
in hdmi_infoframe_unpacks()'s checking. The variable len should be
used instead.
Zero initialize buffer to 0 so it is in a known start state.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting the value of V_WIN_OFF (0x3818) from 0x02 to 0x01 to use GRBG
format still results in wrong color output if data is tuned in BGGR mode
before.
Set default mbus format for the supported modes, but allow the caller of
set(get)_fmt to change the bayer format between BGGR and GRBG.
Set the default mbus format for 3264x2448 (and 1632x1224) to BGGR as the
data sheet states the value of this reg should be 0x02 by default.
If new modes are added in the future, they can add the
mipi_data_mbus_{format} settings into bayer_offset_configs to adjust their
offset regs.
Fixes: 2984b0ddd5 ("media: ov8856: Configure sensor for GRBG Bayer for all modes")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver supports following features:
- phase detection auto focus (PDAF)
- manual exposure and analog/digital gain control
- vblank/hblank control
- test pattern
- image vertical flip and horizontal mirror control
- 4208x3120 at 30FPS
- 2080x1170 at 60FPS
Signed-off-by: Arec Kao <arec.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Obtain the clock frequency by reading the clock-frequency property if
there's no clock.
Fixes: 9fda25332c ("media: i2c: imx258: get clock from device properties and enable it via runtime PM")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TDA1997x driver tried to hold two values in a single variable:
device's "client data" pointer was first set to "sd" in
v4l2_i2c_subdev_init(), then it was overwritten explicitly
using dev_set_drvdata() with "state". This caused
tda1997x_remove() to fail badly.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of the BIT macro for setting individual bits. This improves
readability and safety with respect to shifts.
When on it also remove two zero value disable defines.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Evaluate the desired pixel clock polarity from the device tree.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The real and requested clock can differ and because it is used to
calculate PLL values, the real clock rate should be read.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename V4L2 async notifier functions, replacing "notifier" with "nf" and
removing "_subdev" at the end of the function names adding subdevs as you
can only add subdevs to a notifier. Also wrap and otherwise clean up long
lines.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (imx7)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-9-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TD1997x chip retains vper, hper and hsper register values when the
HDMI source is disconnected. Use a different means of checking if the
link is still valid.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The colon isn't followed by anything here.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For ov8856 working with ACPI, it does not depend on the reset gpio
and regulator to do reset and power control, so should get the gpio
and regulator for non-ACPI cases only, otherwise it will break ov8856
with ACPI.
[Sakari Ailus: Wrap a line over 80 chars.]
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Cc: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the RGB digital gains of ov9734 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the RGB digital gains of ov2740 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the pre_streamon callback to transition the transmitter to either
LP-11 or LP-111 mode if supported by the sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.
Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.
Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to media bus pixel codes definition, data formats on serial
busses should be described with one bus sample per pixel.
Documentation/userspace-api/media/v4l/subdev-formats.rst states:
"The media bus pixel codes document parallel formats. Should the pixel
data be transported over a serial bus, the media bus pixel code that
describes a parallel format that transfers a sample on a single clock
cycle is used. For instance, both MEDIA_BUS_FMT_BGR888_1X24 and
MEDIA_BUS_FMT_BGR888_3X8 are used on parallel busses for transferring an
8 bits per sample BGR data, whereas on serial busses the data in this
format is only referred to using MEDIA_BUS_FMT_BGR888_1X24. This is
because there is effectively only a single way to transport that
format on the serial busses."
Some MIPI CSI receivers strictly obey this definition and declare
support for only *1X_* formats.
Hence, complement the supported media bus formats with their 1X16 versions
(currently applicable to yuyv, uyvy) to enhance interoperability with CSI
receivers.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the OmniVisison ov9282
black&white image sensor.
The camera sensor uses the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 1280x720 @ 30fps
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the Sony imx412 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 4056x3040 @ 30fps
- supported bayer order output:
- SRGGB10
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the Sony imx335 image sensor.
ThE camera sensor uses the i2c bus for control and the csi-2
bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 2592x1940 @ 30fps
- supported bayer order output:
- SRGGB12
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Captured video would be out of sync when using the adv7280 with
the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) had to
be configured properly to ensure BT.656-4 compatibility.
An error in the adv7280 reference manual suggested that EAV/SAV mode
was enabled by default, however upon inspecting register 0x31, it was
determined to be disabled by default.
[fabio: Introduce "adv,force-bt656-4" to not affect the existing users]
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a reset input that can be controlled by GPIO. Let's add it
to let the driver control it if required.
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
deleted the repeated word 'the' in the comments.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10635 image sensor embedded in the camera module is currently
reset after the MAX9271 initialization with two long delays that were
most probably not correctly characterized.
Re-work the image sensor reset procedure by holding the chip in reset
during the MAX9271 configuration, removing the long sleep delays and
only wait after the chip exits from reset for 350-500 microseconds
interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout
characterized in the chip manual.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The camera module initialization routine does not check the return
value of a few functions. Fix that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the device is identified the driver currently reports the
names of the chips embedded in the camera module.
Report the name of the camera module itself instead.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the noise immunity threshold at the end of the rdacm20
initialization routine.
The rdacm20 camera module has been so far tested with a startup
delay that allowed the embedded MCU to program the serializer. If
the initialization routine is run before the MCU programs the
serializer and the image sensor and their addresses gets changed
by the rdacm20 driver it is required to manually enable the noise
immunity threshold to make the communication on the control channel
more reliable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no reason to allocate dynamically the 'serializer' field in
the driver structure.
Embed the field and adjust all its users in the driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current RDACM21 initialization routine powers up the OV10640 image
sensor after the OV490 ISP. The ISP is programmed with a firmware loaded
from an embedded serial flash that (most probably) tries to interact and
program also the image sensor connected to the ISP.
As described in commit "media: i2c: rdacm21: Fix OV10640 powerup" the
image sensor powerdown signal is kept high by an internal pull up
resistor and occasionally fails to startup correctly if the powerdown
line is not asserted explicitly. Failures in the OV10640 startup causes
the OV490 firmware to fail to boot correctly resulting in the camera
module initialization to fail consequentially.
Fix this by powering up the OV10640 image sensor before testing the
OV490 firmware boot completion, by splitting the ov10640_initialize()
function in an ov10640_power_up() one and an ov10640_check_id() one.
Also make sure the OV10640 identification procedure gives enough time to
the image sensor to resume after the programming phase performed by the
OV490 firmware by repeating the ID read procedure.
This commit fixes a sporadic start-up error triggered by a failure to
detect the OV490 firmware boot completion:
rdacm21 8-0054: Timeout waiting for firmware boot
[hverkuil: fixed two typos in commit log]
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10640 image sensor powerdown signal is controlled by the first
line of the OV490 GPIO pad #1, but the pad #0 identifier
OV490_GPIO_OUTPUT_VALUE0 was erroneously used. As a result the image
sensor powerdown signal was never asserted but was left floating and
kept high by an internal pull-up resistor, causing sporadic failures
during the image sensor startup phase.
Fix this by using the correct GPIO pad identifier and wait the mandatory
1.5 millisecond delay after the powerup lane is asserted. The reset
delay is not characterized in the chip manual if not as "255 XVCLK +
initialization". Wait for at least 3 milliseconds to guarantee the SCCB
bus is available.
While at it also fix the reset sequence, as the reset line was released
before the powerdown one, and the line was not cycled.
This commit fixes a sporadic start-up error triggered by a failure to
read the OV10640 chip ID:
rdacm21 8-0054: OV10640 ID mismatch: (0x01)
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a delay after the OV490 chip is put in reset state. The reset
signal shall be held low for at least 250 useconds.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9271 chip manual prescribes a delay of 5 milliseconds
after the chip exits from low power state.
Add a new function to the max9271 library driver that wakes up the chip
with a dummy i2c transaction and implements the correct delay of 5
milliseconds after the chip exits from low power state.
Use the newly introduced function in the rdacm20 and rdacm21 camera
drivers. The former was not respecting the required delay while the
latter was waiting for a too-short timeout.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of the max9271_write() function in the
max9271 library driver.
While at it, modify an existing condition to be made identical
to other checks.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rephrase a comment in .bound() callback to make it clear we register
a subdev notifier and remove a redundant comment about disabling i2c
auto-ack.
No functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide a macro to define the reverse channel amplitude to
be used to compensate the remote serializer noise immunity.
While at it, update a comment.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cache the current channel amplitude in a driver variable
to skip updating it if the newly requested value is the same
as the currently configured one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the reverse_channel_mv variable to init_rev_chan_mv as
the next patch will cache the reverse channel amplitude in
a new driver variable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to use & to get the start address of an array.
Fix the size of vga_edid.edid to a single block (128 bytes) to fix
this smatch error:
adv7842.c:2538 adv7842_set_edid() error: memcpy() '&state->vga_edid.edid' too small (128 vs 512)
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes: c3fda7f835 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 2561482468 ("[media] tc358743: support probe from device tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The adv7842 driver didn't support EDIDs of 3 or 4 blocks, even though the
hardware supports this.
It is a bit more complicated due to the fact that the adv7842 can expose
two EDIDs: one digital, one analog, for DVI-I connectors. In that case the
VGA_EDID_ENABLE bit is set and blocks 0 and 1 of the EDID eeprom are used
for the DVI-D part and block 2 is used for the DVI-A part of the DVI-I
connector.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 0 here and printing -ENODEV wouldn't be really
helpful. So remove it from the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 0 here and printing -ENODEV wouldn't be really
helpful. So remove it from the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2 sub-device driver for the Sony IMX208 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
[Sakari Ailus: Rename sensor async register function to make it compile,
use exposure_max and wrap a few long lines.]
Signed-off-by: Ping-Chung Chen <ping-chung.chen@intel.com>
Signed-off-by: Yeh, Andy <andy.yeh@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The check on mode_index is sufficient to ensure that we have a
valid mode. Remove the explicit mode check similarly to
commit 38a5023029 ("media: i2c: ov5648: remove unnecessary NULL check")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV8856 sensor can output frames with 2/4 CSI2 data lanes.
This commit adds support for 2 lane mode in addition to the 4 lane
and also configuring the data lane settings in the driver based on
system configuration.
- Fix Bayer order output in 1640x1232 binning registers
- supported data lanes
+ 3280x2464 on 2 & 4 lanes
+ 1640x1232 on 2 & 4 lanes
+ 3264x2448 on 4 lanes
+ 1632x1224 on 4 lanes
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Acked-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some platform(imx6q), xvclk might not switch on in advance,
also for power save purpose, xvclk should not be always on.
so, add clk_prepare_enable(), clk_disable_unprepare() in driver
side to set xvclk on/off at proper stage.
Add following changes:
- add 'struct clk *clk;' in 'struct ov2659 {}'
- enable xvclk in ov2659_power_on()
- disable xvclk in ov2659_power_off()
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to the CCS spec the op_pll_multiplier address is 0x030e,
not 0x031e.
Signed-off-by: Bernhard Wimmer <be.wimm@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: 6493c4b777 ("media: smiapp: Import CCS definitions")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2 async framework is generally used with the V4L2 fwnode, which
also depends on the former. There are a few exceptions but they are
relatively few.
At the same time there is a vast number of systems that need videodev
module, but have no use for v4l2-async that's now part of videodev.
In order to improve, split the v4l2-async into its own module. Selecting
V4L2_FWNODE also selects V4L2_ASYNC.
This also moves the initialisation of the debufs entries for async subdevs
to loading of the v4l2-async module. The directory is named as
"v4l2-async".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 1 here. In fact 'i' is expected instead.
Store the return value of 'i2c_master_recv()' in 'ret' so that the error
message print the correct error code.
Fixes: acaa34bf06 ("media: rc: implement zilog transmitter")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822 ("[media] V4L: Add S5C73M3 camera driver")
Fixes: 8b99312b72 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor")
Fixes: 7d459937dc ("[media] Add driver for Samsung S5K5BAF camera sensor")
Fixes: bfa8dd3a05 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PM runtime get logic is currently broken, as it checks if
ret is zero instead of checking if it is an error code,
as reported by Dan Carpenter.
While here, use the pm_runtime_resume_and_get() as added by:
commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors. As a bonus, such function
always return zero on success.
It should also be noticed that a fail of pm_runtime_get_sync() would
potentially result in a spurious runtime_suspend(), instead of
using pm_runtime_put_noidle().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
There is a bug at ccs_pm_get_init(): when this function returns
an error, the stream is not started, and RPM usage_count
should not be incremented. However, if the calls to
v4l2_ctrl_handler_setup() return errors, it will be kept
incremented.
At ccs_suspend() the best is to replace it by the new
pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter automatically,
in the case of errors.
Fixes: 96e3a6b92f ("media: smiapp: Avoid maintaining power state information")
Cc: stable@vger.kernel.org
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If pm_runtime resume logic fails, return the error code
provided by it, instead of -EAGAIN, as, depending on what
caused it to fail, it may not be something that would be
recovered.
Fixes: cbba45d436 ("[media] smiapp: Use runtime PM")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for EDIDs consisting of one EDID block.
Related to this, improve CEC physical address handling.
Clearing the EDID caused a bug since v4l2_calc_aspect_ratio() was
called with a NULL pointer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Only the first pad was configured, but there are 4. This causes
set_fmt to fail with -EINVAL since the passed pad is > 0.
Configure all three sink pads and the source pad.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sparse reports a warning on a cast to u8 of a 16 bits constant.
drivers/media/i2c/rdacm21.c:348:62: warning: cast truncates bits
from constant value (300a becomes a)
Even if the behaviour is intended, silence the sparse warning replacing
the cast with a bitwise & operation.
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the EDID has an odd number of blocks (usually just 1, but the
same problem occurs with 3 blocks), then VIDIOC_G_EDID reported 2
(or 4) blocks. Fix this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While the adv7604/11/12 hardware supported EDIDs up to 4 blocks, the
driver didn't. This patch adds support for this. It also improves support
for EDIDs that do not have a Source Physical Address: in that case the
spa location is set to the first byte of the second block, and the
'physical address' is just the two bytes at that location. This is per
the suggestion in the adv76xx documentation for such EDIDs.
Tested with an adv7604 and adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For the adv7604 the hotplug detect pin is controlled through gpio pins from
the SoC, but the adv7611 and adv7612 control the hotplug detect pin
themselves.
But the driver had no support for this, so the HPD was always high, even
when changing the EDID. Add proper support for this to the driver.
Tested with an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 supports High Dynamic Range with 5 levels of low/high
exposure ratio. Add a V4L2 control for HDR (WIDE_DYNAMIC_RANGE).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move incrementing/decrementing runtime PM count to
imx219_start_streaming()/imx219_stop_streaming() functions respectively.
This fixes an issue of unbalanced runtime PM count in resume callback
error path where streaming is stopped and runtime PM count is left
unbalanced.
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
