The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-6-krzysztof.kozlowski@linaro.org
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
for 5.18, please pull the following:
- Krzysztof aligns the PL330 DMA controller node name to the schema
- Rafal corrects the TWD (Timer/Watchdog) block, adds the watchdog node,
I2C controller node and the pinctrl node for the 4908 SoC
- Kuldeep fixes the Northstar 2 SPI properties as well as the PL022 SPI
controller clock names
- Frank fixes the SATA node names to conform to the AHCI controller
schema
-----BEGIN PGP SIGNATURE-----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=nJaL
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=B+QM
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.18/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree updates
for 5.18, please pull the following:
- Krzysztof aligns the PL330 DMA controller node name to the schema
- Rafal corrects the TWD (Timer/Watchdog) block, adds the watchdog node,
I2C controller node and the pinctrl node for the 4908 SoC
- Kuldeep fixes the Northstar 2 SPI properties as well as the PL022 SPI
controller clock names
- Frank fixes the SATA node names to conform to the AHCI controller
schema
* tag 'arm-soc/for-5.18/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: stingray: Fix spi clock name
arm64: dts: ns2: Fix spi clock name
arm64: dts: broadcom: Fix sata nodename
arm64: dts: ns2: Fix spi-cpol and spi-cpha property
arm64: dts: broadcom: bcm4908: add I2C block
arm64: dts: broadcom: bcm4908: add watchdog block
arm64: dts: broadcom: bcm4908: add pinctrl binding
arm64: dts: broadcom: bcm4908: use proper TWD binding
arm64: dts: broadcom: align pl330 node name with dtschema
Link: https://lore.kernel.org/r/20220307194817.3754107-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SPI clock name for pl022 is "sspclk" and not "spiclk".
Also fix below dtc warning:
clock-names:0: 'spiclk' is not one of ['SSPCLK', 'sspclk']
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
SPI clock name for pl022 is "sspclk" and not "spiclk".
Also fix below dtc warning:
clock-names:0: 'spiclk' is not one of ['SSPCLK', 'sspclk']
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
After converting ahci-platform txt binding to yaml nodename is reported
as not matching the standard:
arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dt.yaml:
ahci@663f2000: $nodename:0: 'ahci@663f2000' does not match '^sata(@.*)?$'
Fix it to match binding.
Fixes: ac9aae00f0 ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom ns2 platform has spi-cpol and spi-cpho properties set
incorrectly. As per spi-slave-peripheral-prop.yaml, these properties are
of flag or boolean type and not integer type. Fix the values.
Fixes: d69dbd9f41 (arm64: dts: Add ARM PL022 SPI DT nodes for NS2)
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: Ray Jui <rjui@broadcom.com>
CC: Scott Branden <sbranden@broadcom.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has the same watchdog as BCM63xx devices. Use "brcm,bcm6345-wdt"
binding which matches the first SoC with that block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds a reference to the dts of the Raspberry Pi Zero 2 W,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Block at <ff800400 0x4c> is a TWD that contains timers, watchdog and
reset. Actual timers happen to be at block beginning but they only span
across the first 0x28 registers. It means the old block description was
incorrect (size 0x3c).
Drop timers binding for now and use documented TWD binding. Timers
should be properly documented and defined as TWD subnode.
Fixes: 2961f69f15 ("arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes dtbs_check warnings like:
dma@310000: $nodename:0: 'dma@310000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's a home router based on BCM4908 SoC. It has: 1 GiB of RAM, 512 MiB
NAND flash, 6 Ethernet ports and 3 x BCM43684 (WiFi). One of Ethernet
ports is "2.5 G Multi-Gig port" that isn't described yet (it isn't known
how it's wired up).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
for 5.16, please pull the following:
- Rafal updates the BCM4908 DTS files to produce fewer warnings by
fixing the UART clock name, moving the reboot syscon node out of the bus
node, and finally updating the NAND controller node names.
-----BEGIN PGP SIGNATURE-----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=i+W/
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFvOwUACgkQmmx57+YA
GNnBnRAAi79rUBLoOxdvWrdTT5hJaMAPBSaeu6rPvM7VRPSGwUbFdE+oFhkw383P
dxYsIw/fLapdWjPBUmknWjqspazB8MdUT0o8kpT1y7lJZ1T//W4ZG6nBAAbaeeI0
3BciNN+xkF+7ksVWkRX6MJhG3qljN123oUdxZPT+X/W1fvFOs7RoGnRFpAxpVG9t
qoTCXbLPODU+Ug9p+5HhUIMzWWtqF5xItD53GgTHKv0XLkgMinq/ye/8BH9Bps6J
b908GCRvZKlgxSM/tX1wygJu+UDAHkjOgoZLtgtZPoVrLHx4QbyBa1Ut2U5RXe3f
1YGSyaST1AuYtNpkn6Srn9yWH9ZsZ6QunHt4kYBKrjH7JeyLOcvPyCbh2gmyoD5W
ftdTE49ggN69LVTsoWhnTHNE36zXWEgmu387fCo+ABKudZZfzzDRnk4tK4vmcDXC
OnOkOXVagD7YMmyhmH2peCgbjMhH7cHUWBgw50SQvQAc4ueMfdogqGZcU21ogsLN
+oAp0vwHsvS6a2Yv1ivUNRt0YiMB1PqENYR4zUvBAYmG5G9lQc2Szg/H3tK1KOJJ
MUjT+9Cb/IUr9SUt7+Yj4TufeONQjvt+M3Q76fx/ziwLqjFDMjbVWCR5Th8OFp8R
I7hVKCeXAgM/ttWMSnq8HRyrvWfjlLlm/FZvoj1o+lHpkzxKr6Q=
=wvRL
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.16, please pull the following:
- Rafal updates the BCM4908 DTS files to produce fewer warnings by
fixing the UART clock name, moving the reboot syscon node out of the bus
node, and finally updating the NAND controller node names.
* tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm4908: Fix UART clock name
arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus
arm64: dts: broadcom: bcm4908: Fix NAND node name
Link: https://lore.kernel.org/r/20211013174016.831348-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a reference to the dts of the Raspberry Pi Compute Module 4
IO Board, so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-11-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
According to the binding the correct clock name is "refclk".
Fixes: 2961f69f15 ("arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This fixes following error for every bcm4908 DTS file:
bus@ff800000: reboot: {'type': 'object'} is not allowed for {'compatible': ['syscon-reboot'], 'regmap': [[15]], 'offset': [[52]], 'mask': [[1]]}
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
please pull the following:
- Zhen fixes the Broadcom stingray serial node unit names to fix a DT
binding warning
-----BEGIN PGP SIGNATURE-----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=6wtT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.14/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs changes for 5.14,
please pull the following:
- Zhen fixes the Broadcom stingray serial node unit names to fix a DT
binding warning
* tag 'arm-soc/for-5.14/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: normalize the node name of the UART devices
Link: https://lore.kernel.org/r/20210610194836.309869-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a reference to the dts of the Raspberry Pi 400,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/1622981777-5023-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Change the node name of the UART devices to match
"^serial(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
On most BCM4908 devices MAC address can be read from the bootloader
binary section containing device settings. Use NVMEM to describe that.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This hardware supports two interrupts, one per DMA channel (RX and TX).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Archer C2300 V1 is a home router based on the BCM4906 (2 CPU cores). It
has 512 MiB of RAM, NAND flash, USB 2.0 and USB 3.0 ports, 4 LAN ports,
1 WAN port.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Ethernet switch and MDIO are grouped using "simple-bus". It's not
allowed to use "ethernet-switch" node name as it isn't a switch. Replace
it with "bus".
Fixes: 527a3ac9bd ("arm64: dts: broadcom: bcm4908: describe internal switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 bootloader supports multiple firmware partitions and has its own
bindings defined for them.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are a few more GPIO connected LEDs there didn't get described
initially.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 uses slightly modified STB family USB PHY. It handles OHCI/EHCI
and XHCI. It requires powering up using the PMB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Remove SATA from Stingray as it is unsupported.
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always
connected to the internal PHYs. Remaining ports depend on device setup.
Asus GT-AC5300 has an extra switch with its PHYs accessible using the
internal MDIO.
CPU port and Ethernet interface remain to be documented.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This reset controller is a single register in the Broadcom's MISC block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has controller that needs different IRQ handling just like the
BCM63138. Describe it properly.
On Linux this change fixes:
brcmstb_nand ff801800.nand: timeout waiting for command 0x9
brcmstb_nand ff801800.nand: intfc status d0000000
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Netgear R8000P is home router based on BCM4906 that is a cheaper variant
of BCM4908 (e.g. 2 cores instead of 4).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
They don't descibe hardware fully yet but it's enough to boot a system.
Some missing blocks:
1. PMC (Power Management Controller?)
2. Ethernet
3. Crypto
4. Thermal
Asus DTS is missing defining full NAND partitions layout and buttons.
Further changes will fill those gaps as soon as required bindings will
be found / tested / added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: ff73917d38 ("ARM64: dts: Add QSPI Device Tree node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SP805 binding sets the name for the actual watchdog clock to
"wdog_clk" (with an underscore).
Change the name in the DTs for Broadcom platforms to match that. The
Linux and U-Boot driver use the *first* clock for this purpose anyway,
so it does not break anything.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
