There are 40 branches this time, adding a lot of new hardware
support, and cleanups. Krzysztof Kozlowski continues his treewide
cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the RZ/G2L
general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for designing
custom SoCs, the support for now is for the Fixed Virtual Platform
emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used
in upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly
for 32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based
IOT board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch,
a Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568
-----BEGIN PGP SIGNATURE-----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=LsM7
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT updates from Arnd Bergmann:
"There are 40 branches this time, adding a lot of new hardware support,
and cleanups. Krzysztof Kozlowski continues his treewide cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the
RZ/G2L general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for
designing custom SoCs, the support for now is for the Fixed Virtual
Platform emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly for
32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based IOT
board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch, a
Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568"
* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
ARM: dts: turris-omnia: Add atsha204a node
arm64: dts: mt8192: Follow binding order for SCP registers
arm64: dts: mediatek: add mtk-snfi for mt7622
arm64: dts: mediatek: mt8195-demo: enable uart1
...
The gpio-keys define module level wake-up pin functionality. Move it
from the carrier board dts file to the Som dtsi file.
While at it, also re-order the properties in the gpio-keys node
alphabetically and rename to sub-node from power to wakeup.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Prepare in-tree device trees for out-of-tree device tree overlay support
(eMMC SKU only).
Relocate panel-dpi default to edt,et057090dhu (RGB 18bit VGA 640x480)
to the module-level dtsi and remove it from the carrier board dtsi.
Keep backlight, resistive touch and Atmel maxtouch nodes enabled
for both eMMC and NAND modules.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to many carrier boards pulling the usdhc1 signals up to 3.3 volt we
need to disable 1.8 volt signaling. Adding the no-1-8-v property
basically disables UHS-I modes by default.
Also pull-up the command and data lines to the +V3.3_1.8_SD rail and
set them to the 200 MHz speed grade (e.g. pinmux bits 7-6: meaning 11
SPEED_3_max_200MHz).
Explicitly specify a bus-width of <4> in the module-level device tree
include file and drop the no-1-8-v property from the carrier boards
device trees.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all Atmel nodes from the board-level into the main module-level
device tree and prepare the device trees for use with Atmel MXT device
tree overlays. Also, add required pinmux groups.
The common scheme for pin groups in touch screen overlays is as follows:
- pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST signals (default)
- pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the proper phy-supply to the FEC. This supply is actually
switched by a clock that is now properly stated. This has the advantage
to add a delay for that particular regulator which is needed.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch on 22 kOhm pull-ups and lower the I2C frequency to around 40 kHz
to get more reliable communication.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the keeper and enable a 100k pull-down on the ADC pins as per
the following note in section 13.2 of the i.MX 6ULL Application
Processor Reference Manual, Rev. 1, 11/2017 [1]:
The keeper causes an undesired jump behavior in ADC. To avoid the
problem, disable keeper before starting ADC.
[1] https://www.nxp.com/webapp/Download?colCode=IMX6ULLRM
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
Fixes: c2e4987e0e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device tree for a Colibri iMX6ULL 1GB which has a eMMC instead of
the raw NAND used on other SKUs.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current setting reflects about 86 Ohms of source-impedance
on the SDIO signals where the WiFi board is hooked up. PCB traces are
routed with 50 Ohms impedance and there are no serial resistors on
those traces.
This commit changes the source-impedance to 52 Ohms to better match our
hardware design.
The impedances given in this commit message refer to 3.3V operation.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.
This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit d2d0ad2aec ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
