Spectre v4 gadgets make use of memory disambiguation, which is a set of
techniques that execute memory access instructions, that is, loads and
stores, out of program order; Intel's optimization manual, section 2.4.4.5:
A load instruction micro-op may depend on a preceding store. Many
microarchitectures block loads until all preceding store addresses are
known. The memory disambiguator predicts which loads will not depend on
any previous stores. When the disambiguator predicts that a load does
not have such a dependency, the load takes its data from the L1 data
cache. Eventually, the prediction is verified. If an actual conflict is
detected, the load and all succeeding instructions are re-executed.
af86ca4e30 ("bpf: Prevent memory disambiguation attack") tried to mitigate
this attack by sanitizing the memory locations through preemptive "fast"
(low latency) stores of zero prior to the actual "slow" (high latency) store
of a pointer value such that upon dependency misprediction the CPU then
speculatively executes the load of the pointer value and retrieves the zero
value instead of the attacker controlled scalar value previously stored at
that location, meaning, subsequent access in the speculative domain is then
redirected to the "zero page".
The sanitized preemptive store of zero prior to the actual "slow" store is
done through a simple ST instruction based on r10 (frame pointer) with
relative offset to the stack location that the verifier has been tracking
on the original used register for STX, which does not have to be r10. Thus,
there are no memory dependencies for this store, since it's only using r10
and immediate constant of zero; hence af86ca4e30 /assumed/ a low latency
operation.
However, a recent attack demonstrated that this mitigation is not sufficient
since the preemptive store of zero could also be turned into a "slow" store
and is thus bypassed as well:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
31: (7b) *(u64 *)(r10 -16) = r2
// r9 will remain "fast" register, r10 will become "slow" register below
32: (bf) r9 = r10
// JIT maps BPF reg to x86 reg:
// r9 -> r15 (callee saved)
// r10 -> rbp
// train store forward prediction to break dependency link between both r9
// and r10 by evicting them from the predictor's LRU table.
33: (61) r0 = *(u32 *)(r7 +24576)
34: (63) *(u32 *)(r7 +29696) = r0
35: (61) r0 = *(u32 *)(r7 +24580)
36: (63) *(u32 *)(r7 +29700) = r0
37: (61) r0 = *(u32 *)(r7 +24584)
38: (63) *(u32 *)(r7 +29704) = r0
39: (61) r0 = *(u32 *)(r7 +24588)
40: (63) *(u32 *)(r7 +29708) = r0
[...]
543: (61) r0 = *(u32 *)(r7 +25596)
544: (63) *(u32 *)(r7 +30716) = r0
// prepare call to bpf_ringbuf_output() helper. the latter will cause rbp
// to spill to stack memory while r13/r14/r15 (all callee saved regs) remain
// in hardware registers. rbp becomes slow due to push/pop latency. below is
// disasm of bpf_ringbuf_output() helper for better visual context:
//
// ffffffff8117ee20: 41 54 push r12
// ffffffff8117ee22: 55 push rbp
// ffffffff8117ee23: 53 push rbx
// ffffffff8117ee24: 48 f7 c1 fc ff ff ff test rcx,0xfffffffffffffffc
// ffffffff8117ee2b: 0f 85 af 00 00 00 jne ffffffff8117eee0 <-- jump taken
// [...]
// ffffffff8117eee0: 49 c7 c4 ea ff ff ff mov r12,0xffffffffffffffea
// ffffffff8117eee7: 5b pop rbx
// ffffffff8117eee8: 5d pop rbp
// ffffffff8117eee9: 4c 89 e0 mov rax,r12
// ffffffff8117eeec: 41 5c pop r12
// ffffffff8117eeee: c3 ret
545: (18) r1 = map[id:4]
547: (bf) r2 = r7
548: (b7) r3 = 0
549: (b7) r4 = 4
550: (85) call bpf_ringbuf_output#194288
// instruction 551 inserted by verifier \
551: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
// storing map value pointer r7 at fp-16 | since value of r10 is "slow".
552: (7b) *(u64 *)(r10 -16) = r7 /
// following "fast" read to the same memory location, but due to dependency
// misprediction it will speculatively execute before insn 551/552 completes.
553: (79) r2 = *(u64 *)(r9 -16)
// in speculative domain contains attacker controlled r2. in non-speculative
// domain this contains r7, and thus accesses r7 +0 below.
554: (71) r3 = *(u8 *)(r2 +0)
// leak r3
As can be seen, the current speculative store bypass mitigation which the
verifier inserts at line 551 is insufficient since /both/, the write of
the zero sanitation as well as the map value pointer are a high latency
instruction due to prior memory access via push/pop of r10 (rbp) in contrast
to the low latency read in line 553 as r9 (r15) which stays in hardware
registers. Thus, architecturally, fp-16 is r7, however, microarchitecturally,
fp-16 can still be r2.
Initial thoughts to address this issue was to track spilled pointer loads
from stack and enforce their load via LDX through r10 as well so that /both/
the preemptive store of zero /as well as/ the load use the /same/ register
such that a dependency is created between the store and load. However, this
option is not sufficient either since it can be bypassed as well under
speculation. An updated attack with pointer spill/fills now _all_ based on
r10 would look as follows:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
[...]
// longer store forward prediction training sequence than before.
2062: (61) r0 = *(u32 *)(r7 +25588)
2063: (63) *(u32 *)(r7 +30708) = r0
2064: (61) r0 = *(u32 *)(r7 +25592)
2065: (63) *(u32 *)(r7 +30712) = r0
2066: (61) r0 = *(u32 *)(r7 +25596)
2067: (63) *(u32 *)(r7 +30716) = r0
// store the speculative load address (scalar) this time after the store
// forward prediction training.
2068: (7b) *(u64 *)(r10 -16) = r2
// preoccupy the CPU store port by running sequence of dummy stores.
2069: (63) *(u32 *)(r7 +29696) = r0
2070: (63) *(u32 *)(r7 +29700) = r0
2071: (63) *(u32 *)(r7 +29704) = r0
2072: (63) *(u32 *)(r7 +29708) = r0
2073: (63) *(u32 *)(r7 +29712) = r0
2074: (63) *(u32 *)(r7 +29716) = r0
2075: (63) *(u32 *)(r7 +29720) = r0
2076: (63) *(u32 *)(r7 +29724) = r0
2077: (63) *(u32 *)(r7 +29728) = r0
2078: (63) *(u32 *)(r7 +29732) = r0
2079: (63) *(u32 *)(r7 +29736) = r0
2080: (63) *(u32 *)(r7 +29740) = r0
2081: (63) *(u32 *)(r7 +29744) = r0
2082: (63) *(u32 *)(r7 +29748) = r0
2083: (63) *(u32 *)(r7 +29752) = r0
2084: (63) *(u32 *)(r7 +29756) = r0
2085: (63) *(u32 *)(r7 +29760) = r0
2086: (63) *(u32 *)(r7 +29764) = r0
2087: (63) *(u32 *)(r7 +29768) = r0
2088: (63) *(u32 *)(r7 +29772) = r0
2089: (63) *(u32 *)(r7 +29776) = r0
2090: (63) *(u32 *)(r7 +29780) = r0
2091: (63) *(u32 *)(r7 +29784) = r0
2092: (63) *(u32 *)(r7 +29788) = r0
2093: (63) *(u32 *)(r7 +29792) = r0
2094: (63) *(u32 *)(r7 +29796) = r0
2095: (63) *(u32 *)(r7 +29800) = r0
2096: (63) *(u32 *)(r7 +29804) = r0
2097: (63) *(u32 *)(r7 +29808) = r0
2098: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; same as before, also including the
// sanitation store with 0 from the current mitigation by the verifier.
2099: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
2100: (7b) *(u64 *)(r10 -16) = r7 | since store unit is still busy.
// load from stack intended to bypass stores.
2101: (79) r2 = *(u64 *)(r10 -16)
2102: (71) r3 = *(u8 *)(r2 +0)
// leak r3
[...]
Looking at the CPU microarchitecture, the scheduler might issue loads (such
as seen in line 2101) before stores (line 2099,2100) because the load execution
units become available while the store execution unit is still busy with the
sequence of dummy stores (line 2069-2098). And so the load may use the prior
stored scalar from r2 at address r10 -16 for speculation. The updated attack
may work less reliable on CPU microarchitectures where loads and stores share
execution resources.
This concludes that the sanitizing with zero stores from af86ca4e30 ("bpf:
Prevent memory disambiguation attack") is insufficient. Moreover, the detection
of stack reuse from af86ca4e30 where previously data (STACK_MISC) has been
written to a given stack slot where a pointer value is now to be stored does
not have sufficient coverage as precondition for the mitigation either; for
several reasons outlined as follows:
1) Stack content from prior program runs could still be preserved and is
therefore not "random", best example is to split a speculative store
bypass attack between tail calls, program A would prepare and store the
oob address at a given stack slot and then tail call into program B which
does the "slow" store of a pointer to the stack with subsequent "fast"
read. From program B PoV such stack slot type is STACK_INVALID, and
therefore also must be subject to mitigation.
2) The STACK_SPILL must not be coupled to register_is_const(&stack->spilled_ptr)
condition, for example, the previous content of that memory location could
also be a pointer to map or map value. Without the fix, a speculative
store bypass is not mitigated in such precondition and can then lead to
a type confusion in the speculative domain leaking kernel memory near
these pointer types.
While brainstorming on various alternative mitigation possibilities, we also
stumbled upon a retrospective from Chrome developers [0]:
[...] For variant 4, we implemented a mitigation to zero the unused memory
of the heap prior to allocation, which cost about 1% when done concurrently
and 4% for scavenging. Variant 4 defeats everything we could think of. We
explored more mitigations for variant 4 but the threat proved to be more
pervasive and dangerous than we anticipated. For example, stack slots used
by the register allocator in the optimizing compiler could be subject to
type confusion, leading to pointer crafting. Mitigating type confusion for
stack slots alone would have required a complete redesign of the backend of
the optimizing compiler, perhaps man years of work, without a guarantee of
completeness. [...]
From BPF side, the problem space is reduced, however, options are rather
limited. One idea that has been explored was to xor-obfuscate pointer spills
to the BPF stack:
[...]
// preoccupy the CPU store port by running sequence of dummy stores.
[...]
2106: (63) *(u32 *)(r7 +29796) = r0
2107: (63) *(u32 *)(r7 +29800) = r0
2108: (63) *(u32 *)(r7 +29804) = r0
2109: (63) *(u32 *)(r7 +29808) = r0
2110: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; xored with random 'secret' value
// of 943576462 before store ...
2111: (b4) w11 = 943576462
2112: (af) r11 ^= r7
2113: (7b) *(u64 *)(r10 -16) = r11
2114: (79) r11 = *(u64 *)(r10 -16)
2115: (b4) w2 = 943576462
2116: (af) r2 ^= r11
// ... and restored with the same 'secret' value with the help of AX reg.
2117: (71) r3 = *(u8 *)(r2 +0)
[...]
While the above would not prevent speculation, it would make data leakage
infeasible by directing it to random locations. In order to be effective
and prevent type confusion under speculation, such random secret would have
to be regenerated for each store. The additional complexity involved for a
tracking mechanism that prevents jumps such that restoring spilled pointers
would not get corrupted is not worth the gain for unprivileged. Hence, the
fix in here eventually opted for emitting a non-public BPF_ST | BPF_NOSPEC
instruction which the x86 JIT translates into a lfence opcode. Inserting the
latter in between the store and load instruction is one of the mitigations
options [1]. The x86 instruction manual notes:
[...] An LFENCE that follows an instruction that stores to memory might
complete before the data being stored have become globally visible. [...]
The latter meaning that the preceding store instruction finished execution
and the store is at minimum guaranteed to be in the CPU's store queue, but
it's not guaranteed to be in that CPU's L1 cache at that point (globally
visible). The latter would only be guaranteed via sfence. So the load which
is guaranteed to execute after the lfence for that local CPU would have to
rely on store-to-load forwarding. [2], in section 2.3 on store buffers says:
[...] For every store operation that is added to the ROB, an entry is
allocated in the store buffer. This entry requires both the virtual and
physical address of the target. Only if there is no free entry in the store
buffer, the frontend stalls until there is an empty slot available in the
store buffer again. Otherwise, the CPU can immediately continue adding
subsequent instructions to the ROB and execute them out of order. On Intel
CPUs, the store buffer has up to 56 entries. [...]
One small upside on the fix is that it lifts constraints from af86ca4e30
where the sanitize_stack_off relative to r10 must be the same when coming
from different paths. The BPF_ST | BPF_NOSPEC gets emitted after a BPF_STX
or BPF_ST instruction. This happens either when we store a pointer or data
value to the BPF stack for the first time, or upon later pointer spills.
The former needs to be enforced since otherwise stale stack data could be
leaked under speculation as outlined earlier. For non-x86 JITs the BPF_ST |
BPF_NOSPEC mapping is currently optimized away, but others could emit a
speculation barrier as well if necessary. For real-world unprivileged
programs e.g. generated by LLVM, pointer spill/fill is only generated upon
register pressure and LLVM only tries to do that for pointers which are not
used often. The program main impact will be the initial BPF_ST | BPF_NOSPEC
sanitation for the STACK_INVALID case when the first write to a stack slot
occurs e.g. upon map lookup. In future we might refine ways to mitigate
the latter cost.
[0] https://arxiv.org/pdf/1902.05178.pdf
[1] https://msrc-blog.microsoft.com/2018/05/21/analysis-and-mitigation-of-speculative-store-bypass-cve-2018-3639/
[2] https://arxiv.org/pdf/1905.05725.pdf
Fixes: af86ca4e30 ("bpf: Prevent memory disambiguation attack")
Fixes: f7cf25b202 ("bpf: track spill/fill of constants")
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Current max cgroup storage value size is 4k (PAGE_SIZE). The other local
storages accept up to 64k (BPF_LOCAL_STORAGE_MAX_VALUE_SIZE). Let's align
max cgroup value size with the other storages.
For percpu, the max is 32k (PCPU_MIN_UNIT_SIZE) because percpu
allocator is not happy about larger values.
netcnt test is extended to exercise those maximum values
(non-percpu max size is close to, but not real max).
v4:
* remove inner union (Andrii Nakryiko)
* keep net_cnt on the stack (Andrii Nakryiko)
v3:
* refine SIZEOF_BPF_LOCAL_STORAGE_ELEM comment (Yonghong Song)
* anonymous struct in percpu_net_cnt & net_cnt (Yonghong Song)
* reorder free (Yonghong Song)
v2:
* cap max_value_size instead of BUILD_BUG_ON (Martin KaFai Lau)
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210727222335.4029096-1-sdf@google.com
This patch allows bpf tcp iter to call bpf_(get|set)sockopt.
To allow a specific bpf iter (tcp here) to call a set of helpers,
get_func_proto function pointer is added to bpf_iter_reg.
The bpf iter is a tracing prog which currently requires
CAP_PERFMON or CAP_SYS_ADMIN, so this patch does not
impose other capability checks for bpf_(get|set)sockopt.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210701200619.1036715-1-kafai@fb.com
The variable stype is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721115630.109279-1-colin.king@canonical.com
b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed the problem with cgroup-local storage use in BPF by
pre-allocating per-CPU array of 8 cgroup storage pointers to accommodate
possible BPF program preemptions and nested executions.
While this seems to work good in practice, it introduces new and unnecessary
failure mode in which not all BPF programs might be executed if we fail to
find an unused slot for cgroup storage, however unlikely it is. It might also
not be so unlikely when/if we allow sleepable cgroup BPF programs in the
future.
Further, the way that cgroup storage is implemented as ambiently-available
property during entire BPF program execution is a convenient way to pass extra
information to BPF program and helpers without requiring user code to pass
around extra arguments explicitly. So it would be good to have a generic
solution that can allow implementing this without arbitrary restrictions.
Ideally, such solution would work for both preemptable and sleepable BPF
programs in exactly the same way.
This patch introduces such solution, bpf_run_ctx. It adds one pointer field
(bpf_ctx) to task_struct. This field is maintained by BPF_PROG_RUN family of
macros in such a way that it always stays valid throughout BPF program
execution. BPF program preemption is handled by remembering previous
current->bpf_ctx value locally while executing nested BPF program and
restoring old value after nested BPF program finishes. This is handled by two
helper functions, bpf_set_run_ctx() and bpf_reset_run_ctx(), which are
supposed to be used before and after BPF program runs, respectively.
Restoring old value of the pointer handles preemption, while bpf_run_ctx
pointer being a property of current task_struct naturally solves this problem
for sleepable BPF programs by "following" BPF program execution as it is
scheduled in and out of CPU. It would even allow CPU migration of BPF
programs, even though it's not currently allowed by BPF infra.
This patch cleans up cgroup local storage handling as a first application. The
design itself is generic, though, with bpf_run_ctx being an empty struct that
is supposed to be embedded into a specific struct for a given BPF program type
(bpf_cg_run_ctx in this case). Follow up patches are planned that will expand
this mechanism for other uses within tracing BPF programs.
To verify that this change doesn't revert the fix to the original cgroup
storage issue, I ran the same repro as in the original report ([0]) and didn't
get any problems. Replacing bpf_reset_run_ctx(old_run_ctx) with
bpf_reset_run_ctx(NULL) triggers the issue pretty quickly (so repro does work).
[0] https://lore.kernel.org/bpf/YEEvBUiJl2pJkxTd@krava/
Fixes: b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210712230615.3525979-1-andrii@kernel.org
In 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask") we
narrowed the offset mask for unprivileged pointer arithmetic in order to
mitigate a corner case where in the speculative domain it is possible to
advance, for example, the map value pointer by up to value_size-1 out-of-
bounds in order to leak kernel memory via side-channel to user space.
The verifier's state pruning for scalars leaves one corner case open
where in the first verification path R_x holds an unknown scalar with an
aux->alu_limit of e.g. 7, and in a second verification path that same
register R_x, here denoted as R_x', holds an unknown scalar which has
tighter bounds and would thus satisfy range_within(R_x, R_x') as well as
tnum_in(R_x, R_x') for state pruning, yielding an aux->alu_limit of 3:
Given the second path fits the register constraints for pruning, the final
generated mask from aux->alu_limit will remain at 7. While technically
not wrong for the non-speculative domain, it would however be possible
to craft similar cases where the mask would be too wide as in 7fedb63a83.
One way to fix it is to detect the presence of unknown scalar map pointer
arithmetic and force a deeper search on unknown scalars to ensure that
we do not run into a masking mismatch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Follow-up to fe9a5ca7e3 ("bpf: Do not mark insn as seen under speculative
path verification"). The sanitize_insn_aux_data() helper does not serve a
particular purpose in today's code. The original intention for the helper
was that if function-by-function verification fails, a given program would
be cleared from temporary insn_aux_data[], and then its verification would
be re-attempted in the context of the main program a second time.
However, a failure in do_check_subprogs() will skip do_check_main() and
propagate the error to the user instead, thus such situation can never occur.
Given its interaction is not compatible to the Spectre v1 mitigation (due to
comparing aux->seen with env->pass_cnt), just remove sanitize_insn_aux_data()
to avoid future bugs in this area.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-07-15
The following pull-request contains BPF updates for your *net-next* tree.
We've added 45 non-merge commits during the last 15 day(s) which contain
a total of 52 files changed, 3122 insertions(+), 384 deletions(-).
The main changes are:
1) Introduce bpf timers, from Alexei.
2) Add sockmap support for unix datagram socket, from Cong.
3) Fix potential memleak and UAF in the verifier, from He.
4) Add bpf_get_func_ip helper, from Jiri.
5) Improvements to generic XDP mode, from Kumar.
6) Support for passing xdp_md to XDP programs in bpf_prog_run, from Zvi.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sock_map still has Kconfig dependency on CONFIG_INET,
but there is no actual functional dependency on it after we
introduce ->psock_update_sk_prot().
We have to extend it to CONFIG_NET now as we are going to
support AF_UNIX.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210704190252.11866-2-xiyou.wangcong@gmail.com
Adding bpf_get_func_ip helper for BPF_PROG_TYPE_KPROBE programs,
so it's now possible to call bpf_get_func_ip from both kprobe and
kretprobe programs.
Taking the caller's address from 'struct kprobe::addr', which is
defined for both kprobe and kretprobe.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/20210714094400.396467-5-jolsa@kernel.org
Adding bpf_get_func_ip helper for BPF_PROG_TYPE_TRACING programs,
specifically for all trampoline attach types.
The trampoline's caller IP address is stored in (ctx - 8) address.
so there's no reason to actually call the helper, but rather fixup
the call instruction and return [ctx - 8] value directly.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210714094400.396467-4-jolsa@kernel.org
Enabling BPF_TRAMP_F_IP_ARG for trampolines that actually need it.
The BPF_TRAMP_F_IP_ARG adds extra 3 instructions to trampoline code
and is used only by programs with bpf_get_func_ip helper, which is
added in following patch and sets call_get_func_ip bit.
This patch ensures that BPF_TRAMP_F_IP_ARG flag is used only for
trampolines that have programs with call_get_func_ip set.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210714094400.396467-3-jolsa@kernel.org
Teach max stack depth checking algorithm about async callbacks
that don't increase bpf program stack size.
Also add sanity check that bpf_tail_call didn't sneak into async cb.
It's impossible, since PTR_TO_CTX is not available in async cb,
hence the program cannot contain bpf_tail_call(ctx,...);
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-10-alexei.starovoitov@gmail.com
bpf_for_each_map_elem() and bpf_timer_set_callback() helpers are relying on
PTR_TO_FUNC infra in the verifier to validate addresses to subprograms
and pass them into the helpers as function callbacks.
In case of bpf_for_each_map_elem() the callback is invoked synchronously
and the verifier treats it as a normal subprogram call by adding another
bpf_func_state and new frame in __check_func_call().
bpf_timer_set_callback() doesn't invoke the callback directly.
The subprogram will be called asynchronously from bpf_timer_cb().
Teach the verifier to validate such async callbacks as special kind
of jump by pushing verifier state into stack and let pop_stack() process it.
Special care needs to be taken during state pruning.
The call insn doing bpf_timer_set_callback has to be a prune_point.
Otherwise short timer callbacks might not have prune points in front of
bpf_timer_set_callback() which means is_state_visited() will be called
after this call insn is processed in __check_func_call(). Which means that
another async_cb state will be pushed to be walked later and the verifier
will eventually hit BPF_COMPLEXITY_LIMIT_JMP_SEQ limit.
Since push_async_cb() looks like another push_stack() branch the
infinite loop detection will trigger false positive. To recognize
this case mark such states as in_async_callback_fn.
To distinguish infinite loop in async callback vs the same callback called
with different arguments for different map and timer add async_entry_cnt
to bpf_func_state.
Enforce return zero from async callbacks.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-9-alexei.starovoitov@gmail.com
In the following bpf subprogram:
static int timer_cb(void *map, void *key, void *value)
{
bpf_timer_set_callback(.., timer_cb);
}
the 'timer_cb' is a pointer to a function.
ld_imm64 insn is used to carry this pointer.
bpf_pseudo_func() returns true for such ld_imm64 insn.
Unlike bpf_for_each_map_elem() the bpf_timer_set_callback() is asynchronous.
Relax control flow check to allow such "recursion" that is seen as an infinite
loop by check_cfg(). The distinction between bpf_for_each_map_elem() the
bpf_timer_set_callback() is done in the follow up patch.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-8-alexei.starovoitov@gmail.com
BTF is required for 'struct bpf_timer' to be recognized inside map value.
The bpf timers are supported inside inner maps.
Remember 'struct btf *' in inner_map_meta to make it available
to the verifier in the sequence:
struct bpf_map *inner_map = bpf_map_lookup_elem(&outer_map, ...);
if (inner_map)
timer = bpf_map_lookup_elem(&inner_map, ...);
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-7-alexei.starovoitov@gmail.com
bpf_timer_init() arguments are:
1. pointer to a timer (which is embedded in map element).
2. pointer to a map.
Make sure that pointer to a timer actually belongs to that map.
Use map_uid (which is unique id of inner map) to reject:
inner_map1 = bpf_map_lookup_elem(outer_map, key1)
inner_map2 = bpf_map_lookup_elem(outer_map, key2)
if (inner_map1 && inner_map2) {
timer = bpf_map_lookup_elem(inner_map1);
if (timer)
// mismatch would have been allowed
bpf_timer_init(timer, inner_map2);
}
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-6-alexei.starovoitov@gmail.com
Restrict bpf timers to array, hash (both preallocated and kmalloced), and
lru map types. The per-cpu maps with timers don't make sense, since 'struct
bpf_timer' is a part of map value. bpf timers in per-cpu maps would mean that
the number of timers depends on number of possible cpus and timers would not be
accessible from all cpus. lpm map support can be added in the future.
The timers in inner maps are supported.
The bpf_map_update/delete_elem() helpers and sys_bpf commands cancel and free
bpf_timer in a given map element.
Similar to 'struct bpf_spin_lock' BTF is required and it is used to validate
that map element indeed contains 'struct bpf_timer'.
Make check_and_init_map_value() init both bpf_spin_lock and bpf_timer when
map element data is reused in preallocated htab and lru maps.
Teach copy_map_value() to support both bpf_spin_lock and bpf_timer in a single
map element. There could be one of each, but not more than one. Due to 'one
bpf_timer in one element' restriction do not support timers in global data,
since global data is a map of single element, but from bpf program side it's
seen as many global variables and restriction of single global timer would be
odd. The sys_bpf map_freeze and sys_mmap syscalls are not allowed on maps with
timers, since user space could have corrupted mmap element and crashed the
kernel. The maps with timers cannot be readonly. Due to these restrictions
search for bpf_timer in datasec BTF in case it was placed in the global data to
report clear error.
The previous patch allowed 'struct bpf_timer' as a first field in a map
element only. Relax this restriction.
Refactor lru map to s/bpf_lru_push_free/htab_lru_push_free/ to cancel and free
the timer when lru map deletes an element as a part of it eviction algorithm.
Make sure that bpf program cannot access 'struct bpf_timer' via direct load/store.
The timer operation are done through helpers only.
This is similar to 'struct bpf_spin_lock'.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-5-alexei.starovoitov@gmail.com
Introduce 'struct bpf_timer { __u64 :64; __u64 :64; };' that can be embedded
in hash/array/lru maps as a regular field and helpers to operate on it:
// Initialize the timer.
// First 4 bits of 'flags' specify clockid.
// Only CLOCK_MONOTONIC, CLOCK_REALTIME, CLOCK_BOOTTIME are allowed.
long bpf_timer_init(struct bpf_timer *timer, struct bpf_map *map, int flags);
// Configure the timer to call 'callback_fn' static function.
long bpf_timer_set_callback(struct bpf_timer *timer, void *callback_fn);
// Arm the timer to expire 'nsec' nanoseconds from the current time.
long bpf_timer_start(struct bpf_timer *timer, u64 nsec, u64 flags);
// Cancel the timer and wait for callback_fn to finish if it was running.
long bpf_timer_cancel(struct bpf_timer *timer);
Here is how BPF program might look like:
struct map_elem {
int counter;
struct bpf_timer timer;
};
struct {
__uint(type, BPF_MAP_TYPE_HASH);
__uint(max_entries, 1000);
__type(key, int);
__type(value, struct map_elem);
} hmap SEC(".maps");
static int timer_cb(void *map, int *key, struct map_elem *val);
/* val points to particular map element that contains bpf_timer. */
SEC("fentry/bpf_fentry_test1")
int BPF_PROG(test1, int a)
{
struct map_elem *val;
int key = 0;
val = bpf_map_lookup_elem(&hmap, &key);
if (val) {
bpf_timer_init(&val->timer, &hmap, CLOCK_REALTIME);
bpf_timer_set_callback(&val->timer, timer_cb);
bpf_timer_start(&val->timer, 1000 /* call timer_cb2 in 1 usec */, 0);
}
}
This patch adds helper implementations that rely on hrtimers
to call bpf functions as timers expire.
The following patches add necessary safety checks.
Only programs with CAP_BPF are allowed to use bpf_timer.
The amount of timers used by the program is constrained by
the memcg recorded at map creation time.
The bpf_timer_init() helper needs explicit 'map' argument because inner maps
are dynamic and not known at load time. While the bpf_timer_set_callback() is
receiving hidden 'aux->prog' argument supplied by the verifier.
The prog pointer is needed to do refcnting of bpf program to make sure that
program doesn't get freed while the timer is armed. This approach relies on
"user refcnt" scheme used in prog_array that stores bpf programs for
bpf_tail_call. The bpf_timer_set_callback() will increment the prog refcnt which is
paired with bpf_timer_cancel() that will drop the prog refcnt. The
ops->map_release_uref is responsible for cancelling the timers and dropping
prog refcnt when user space reference to a map reaches zero.
This uref approach is done to make sure that Ctrl-C of user space process will
not leave timers running forever unless the user space explicitly pinned a map
that contained timers in bpffs.
bpf_timer_init() and bpf_timer_set_callback() will return -EPERM if map doesn't
have user references (is not held by open file descriptor from user space and
not pinned in bpffs).
The bpf_map_delete_elem() and bpf_map_update_elem() operations cancel
and free the timer if given map element had it allocated.
"bpftool map update" command can be used to cancel timers.
The 'struct bpf_timer' is explicitly __attribute__((aligned(8))) because
'__u64 :64' has 1 byte alignment of 8 byte padding.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-4-alexei.starovoitov@gmail.com
Move ____bpf_spin_lock/unlock into helpers to make it more clear
that quadruple underscore bpf_spin_lock/unlock are irqsave/restore variants.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-3-alexei.starovoitov@gmail.com
Currently bpf_prog_put() is called from the task context only.
With addition of bpf timers the timer related helpers will start calling
bpf_prog_put() from irq-saved region and in rare cases might drop
the refcnt to zero.
To address this case, first, convert bpf_prog_free_id() to be irq-save
(this is similar to bpf_map_free_id), and, second, defer non irq
appropriate calls into work queue.
For example:
bpf_audit_prog() is calling kmalloc and wake_up_interruptible,
bpf_prog_kallsyms_del_all()->bpf_ksym_del()->spin_unlock_bh().
They are not safe with irqs disabled.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210715005417.78572-2-alexei.starovoitov@gmail.com
In bpf_patch_insn_data(), we first use the bpf_patch_insn_single() to
insert new instructions, then use adjust_insn_aux_data() to adjust
insn_aux_data. If the old env->prog have no enough room for new inserted
instructions, we use bpf_prog_realloc to construct new_prog and free the
old env->prog.
There have two errors here. First, if adjust_insn_aux_data() return
ENOMEM, we should free the new_prog. Second, if adjust_insn_aux_data()
return ENOMEM, bpf_patch_insn_data() will return NULL, and env->prog has
been freed in bpf_prog_realloc, but we will use it in bpf_check().
So in this patch, we make the adjust_insn_aux_data() never fails. In
bpf_patch_insn_data(), we first pre-malloc memory for the new
insn_aux_data, then call bpf_patch_insn_single() to insert new
instructions, at last call adjust_insn_aux_data() to adjust
insn_aux_data.
Fixes: 8041902dae ("bpf: adjust insn_aux_data when patching insns")
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210714101815.164322-1-hefengqing@huawei.com
During testing of f263a81451 ("bpf: Track subprog poke descriptors correctly
and fix use-after-free") under various failure conditions, for example, when
jit_subprogs() fails and tries to clean up the program to be run under the
interpreter, we ran into the following freeze:
[...]
#127/8 tailcall_bpf2bpf_3:FAIL
[...]
[ 92.041251] BUG: KASAN: slab-out-of-bounds in ___bpf_prog_run+0x1b9d/0x2e20
[ 92.042408] Read of size 8 at addr ffff88800da67f68 by task test_progs/682
[ 92.043707]
[ 92.044030] CPU: 1 PID: 682 Comm: test_progs Tainted: G O 5.13.0-53301-ge6c08cb33a30-dirty #87
[ 92.045542] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
[ 92.046785] Call Trace:
[ 92.047171] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.047773] ? __bpf_prog_run_args32+0x8b/0xb0
[ 92.048389] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.049019] ? ktime_get+0x117/0x130
[...] // few hundred [similar] lines more
[ 92.659025] ? ktime_get+0x117/0x130
[ 92.659845] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.660738] ? __bpf_prog_run_args32+0x8b/0xb0
[ 92.661528] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.662378] ? print_usage_bug+0x50/0x50
[ 92.663221] ? print_usage_bug+0x50/0x50
[ 92.664077] ? bpf_ksym_find+0x9c/0xe0
[ 92.664887] ? ktime_get+0x117/0x130
[ 92.665624] ? kernel_text_address+0xf5/0x100
[ 92.666529] ? __kernel_text_address+0xe/0x30
[ 92.667725] ? unwind_get_return_address+0x2f/0x50
[ 92.668854] ? ___bpf_prog_run+0x15d4/0x2e20
[ 92.670185] ? ktime_get+0x117/0x130
[ 92.671130] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.672020] ? __bpf_prog_run_args32+0x8b/0xb0
[ 92.672860] ? __bpf_prog_run_args64+0xc0/0xc0
[ 92.675159] ? ktime_get+0x117/0x130
[ 92.677074] ? lock_is_held_type+0xd5/0x130
[ 92.678662] ? ___bpf_prog_run+0x15d4/0x2e20
[ 92.680046] ? ktime_get+0x117/0x130
[ 92.681285] ? __bpf_prog_run32+0x6b/0x90
[ 92.682601] ? __bpf_prog_run64+0x90/0x90
[ 92.683636] ? lock_downgrade+0x370/0x370
[ 92.684647] ? mark_held_locks+0x44/0x90
[ 92.685652] ? ktime_get+0x117/0x130
[ 92.686752] ? lockdep_hardirqs_on+0x79/0x100
[ 92.688004] ? ktime_get+0x117/0x130
[ 92.688573] ? __cant_migrate+0x2b/0x80
[ 92.689192] ? bpf_test_run+0x2f4/0x510
[ 92.689869] ? bpf_test_timer_continue+0x1c0/0x1c0
[ 92.690856] ? rcu_read_lock_bh_held+0x90/0x90
[ 92.691506] ? __kasan_slab_alloc+0x61/0x80
[ 92.692128] ? eth_type_trans+0x128/0x240
[ 92.692737] ? __build_skb+0x46/0x50
[ 92.693252] ? bpf_prog_test_run_skb+0x65e/0xc50
[ 92.693954] ? bpf_prog_test_run_raw_tp+0x2d0/0x2d0
[ 92.694639] ? __fget_light+0xa1/0x100
[ 92.695162] ? bpf_prog_inc+0x23/0x30
[ 92.695685] ? __sys_bpf+0xb40/0x2c80
[ 92.696324] ? bpf_link_get_from_fd+0x90/0x90
[ 92.697150] ? mark_held_locks+0x24/0x90
[ 92.698007] ? lockdep_hardirqs_on_prepare+0x124/0x220
[ 92.699045] ? finish_task_switch+0xe6/0x370
[ 92.700072] ? lockdep_hardirqs_on+0x79/0x100
[ 92.701233] ? finish_task_switch+0x11d/0x370
[ 92.702264] ? __switch_to+0x2c0/0x740
[ 92.703148] ? mark_held_locks+0x24/0x90
[ 92.704155] ? __x64_sys_bpf+0x45/0x50
[ 92.705146] ? do_syscall_64+0x35/0x80
[ 92.706953] ? entry_SYSCALL_64_after_hwframe+0x44/0xae
[...]
Turns out that the program rejection from e411901c0b ("bpf: allow for tailcalls
in BPF subprograms for x64 JIT") is buggy since env->prog->aux->tail_call_reachable
is never true. Commit ebf7d1f508 ("bpf, x64: rework pro/epilogue and tailcall
handling in JIT") added a tracker into check_max_stack_depth() which propagates
the tail_call_reachable condition throughout the subprograms. This info is then
assigned to the subprogram's func[i]->aux->tail_call_reachable. However, in the
case of the rejection check upon JIT failure, env->prog->aux->tail_call_reachable
is used. func[0]->aux->tail_call_reachable which represents the main program's
information did not propagate this to the outer env->prog->aux, though. Add this
propagation into check_max_stack_depth() where it needs to belong so that the
check can be done reliably.
Fixes: ebf7d1f508 ("bpf, x64: rework pro/epilogue and tailcall handling in JIT")
Fixes: e411901c0b ("bpf: allow for tailcalls in BPF subprograms for x64 JIT")
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/618c34e3163ad1a36b1e82377576a6081e182f25.1626123173.git.daniel@iogearbox.net
Subprograms are calling map_poke_track(), but on program release there is no
hook to call map_poke_untrack(). However, on program release, the aux memory
(and poke descriptor table) is freed even though we still have a reference to
it in the element list of the map aux data. When we run map_poke_run(), we then
end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run():
[...]
[ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e
[ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337
[ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399
[ 402.824715] Call Trace:
[ 402.824719] dump_stack+0x93/0xc2
[ 402.824727] print_address_description.constprop.0+0x1a/0x140
[ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824744] kasan_report.cold+0x7c/0xd8
[ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824757] prog_array_map_poke_run+0xc2/0x34e
[ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0
[...]
The elements concerned are walked as follows:
for (i = 0; i < elem->aux->size_poke_tab; i++) {
poke = &elem->aux->poke_tab[i];
[...]
The access to size_poke_tab is a 4 byte read, verified by checking offsets
in the KASAN dump:
[ 402.825004] The buggy address belongs to the object at ffff8881905a7800
which belongs to the cache kmalloc-1k of size 1024
[ 402.825008] The buggy address is located 320 bytes inside of
1024-byte region [ffff8881905a7800, ffff8881905a7c00)
The pahole output of bpf_prog_aux:
struct bpf_prog_aux {
[...]
/* --- cacheline 5 boundary (320 bytes) --- */
u32 size_poke_tab; /* 320 4 */
[...]
In general, subprograms do not necessarily manage their own data structures.
For example, BTF func_info and linfo are just pointers to the main program
structure. This allows reference counting and cleanup to be done on the latter
which simplifies their management a bit. The aux->poke_tab struct, however,
did not follow this logic. The initial proposed fix for this use-after-free
bug further embedded poke data tracking into the subprogram with proper
reference counting. However, Daniel and Alexei questioned why we were treating
these objects special; I agree, its unnecessary. The fix here removes the per
subprogram poke table allocation and map tracking and instead simply points
the aux->poke_tab pointer at the main programs poke table. This way, map
tracking is simplified to the main program and we do not need to manage them
per subprogram.
This also means, bpf_prog_free_deferred(), which unwinds the program reference
counting and kfrees objects, needs to ensure that we don't try to double free
the poke_tab when free'ing the subprog structures. This is easily solved by
NULL'ing the poke_tab pointer. The second detail is to ensure that per
subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do
this, we add a pointer in the poke structure to point at the subprogram value
so JITs can easily check while walking the poke_tab structure if the current
entry belongs to the current program. The aux pointer is stable and therefore
suitable for such comparison. On the jit_subprogs() error path, we omit
cleaning up the poke->aux field because these are only ever referenced from
the JIT side, but on error we will never make it to the JIT, so its fine to
leave them dangling. Removing these pointers would complicate the error path
for no reason. However, we do need to untrack all poke descriptors from the
main program as otherwise they could race with the freeing of JIT memory from
the subprograms. Lastly, a748c6975d ("bpf: propagate poke descriptors to
subprograms") had an off-by-one on the subprogram instruction index range
check as it was testing 'insn_idx >= subprog_start && insn_idx <= subprog_end'.
However, subprog_end is the next subprogram's start instruction.
Fixes: a748c6975d ("bpf: propagate poke descriptors to subprograms")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210707223848.14580-2-john.fastabend@gmail.com
This lifts the restriction on running devmap BPF progs in generic
redirect mode. To match native XDP behavior, it is invoked right before
generic_xdp_tx is called, and only supports XDP_PASS/XDP_ABORTED/
XDP_DROP actions.
We also return 0 even if devmap program drops the packet, as
semantically redirect has already succeeded and the devmap prog is the
last point before TX of the packet to device where it can deliver a
verdict on the packet.
This also means it must take care of freeing the skb, as
xdp_do_generic_redirect callers only do that in case an error is
returned.
Since devmap entry prog is supported, remove the check in
generic_xdp_install entirely.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210702111825.491065-5-memxor@gmail.com
This change implements CPUMAP redirect support for generic XDP programs.
The idea is to reuse the cpu map entry's queue that is used to push
native xdp frames for redirecting skb to a different CPU. This will
match native XDP behavior (in that RPS is invoked again for packet
reinjected into networking stack).
To be able to determine whether the incoming skb is from the driver or
cpumap, we reuse skb->redirected bit that skips generic XDP processing
when it is set. To always make use of this, CONFIG_NET_REDIRECT guard on
it has been lifted and it is always available.
>From the redirect side, we add the skb to ptr_ring with its lowest bit
set to 1. This should be safe as skb is not 1-byte aligned. This allows
kthread to discern between xdp_frames and sk_buff. On consumption of the
ptr_ring item, the lowest bit is unset.
In the end, the skb is simply added to the list that kthread is anyway
going to maintain for xdp_frames converted to skb, and then received
again by using netif_receive_skb_list.
Bulking optimization for generic cpumap is left as an exercise for a
future patch for now.
Since cpumap entry progs are now supported, also remove check in
generic_xdp_install for the cpumap.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/20210702111825.491065-4-memxor@gmail.com
There were a couple of READ_ONCE()-invocations left-over by the devmap
RCU conversion. Convert these to rcu_dereference_check() as well to avoid
complaints from sparse.
Fixes: 782347b6bc ("xdp: Add proper __rcu annotations to redirect map entries")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210629093907.573598-1-toke@redhat.com
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kmemleak scans struct page, but it does not scan the page content. If we
allocate some memory with kmalloc(), then allocate page with alloc_page(),
and if we put kmalloc pointer somewhere inside that page, kmemleak will
report kmalloc pointer as a false positive.
We can instruct kmemleak to scan the memory area by calling kmemleak_alloc()
and kmemleak_free(), but part of struct bpf_ringbuf is mmaped to user space,
and if struct bpf_ringbuf changes we would have to revisit and review size
argument in kmemleak_alloc(), because we do not want kmemleak to scan the
user space memory. Let's simplify things and use kmemleak_not_leak() here.
For posterity, also adding additional prior analysis from Andrii:
I think either kmemleak or syzbot are misreporting this. I've added a
bunch of printks around all allocations performed by BPF ringbuf. [...]
On repro side I get these two warnings:
[vmuser@archvm bpf]$ sudo ./repro
BUG: memory leak
unreferenced object 0xffff88810d538c00 (size 64):
comm "repro", pid 2140, jiffies 4294692933 (age 14.540s)
hex dump (first 32 bytes):
00 af 19 04 00 ea ff ff c0 ae 19 04 00 ea ff ff ................
80 ae 19 04 00 ea ff ff c0 29 2e 04 00 ea ff ff .........)......
backtrace:
[<0000000077bfbfbd>] __bpf_map_area_alloc+0x31/0xc0
[<00000000587fa522>] ringbuf_map_alloc.cold.4+0x48/0x218
[<0000000044d49e96>] __do_sys_bpf+0x359/0x1d90
[<00000000f601d565>] do_syscall_64+0x2d/0x40
[<0000000043d3112a>] entry_SYSCALL_64_after_hwframe+0x44/0xae
BUG: memory leak
unreferenced object 0xffff88810d538c80 (size 64):
comm "repro", pid 2143, jiffies 4294699025 (age 8.448s)
hex dump (first 32 bytes):
80 aa 19 04 00 ea ff ff 00 ab 19 04 00 ea ff ff ................
c0 ab 19 04 00 ea ff ff 80 44 28 04 00 ea ff ff .........D(.....
backtrace:
[<0000000077bfbfbd>] __bpf_map_area_alloc+0x31/0xc0
[<00000000587fa522>] ringbuf_map_alloc.cold.4+0x48/0x218
[<0000000044d49e96>] __do_sys_bpf+0x359/0x1d90
[<00000000f601d565>] do_syscall_64+0x2d/0x40
[<0000000043d3112a>] entry_SYSCALL_64_after_hwframe+0x44/0xae
Note that both reported leaks (ffff88810d538c80 and ffff88810d538c00)
correspond to pages array bpf_ringbuf is allocating and tracking properly
internally. Note also that syzbot repro doesn't close FD of created BPF
ringbufs, and even when ./repro itself exits with error, there are still
two forked processes hanging around in my system. So clearly ringbuf maps
are alive at that point. So reporting any memory leak looks weird at that
point, because that memory is being used by active referenced BPF ringbuf.
It's also a question why repro doesn't clean up its forks. But if I do a
`pkill repro`, I do see that all the allocated memory is /properly/ cleaned
up [and the] "leaks" are deallocated properly.
BTW, if I add close() right after bpf() syscall in syzbot repro, I see that
everything is immediately deallocated, like designed. And no memory leak
is reported. So I don't think the problem is anywhere in bpf_ringbuf code,
rather in the leak detection and/or repro itself.
Reported-by: syzbot+5d895828587f49e7fe9b@syzkaller.appspotmail.com
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
[ Daniel: also included analysis from Andrii to the commit log ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: syzbot+5d895828587f49e7fe9b@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/CAEf4BzYk+dqs+jwu6VKXP-RttcTEGFe+ySTGWT9CRNkagDiJVA@mail.gmail.com
Link: https://lore.kernel.org/lkml/YNTAqiE7CWJhOK2M@nuc10
Link: https://lore.kernel.org/lkml/20210615101515.GC26027@arm.com
Link: https://syzkaller.appspot.com/bug?extid=5d895828587f49e7fe9b
Link: https://lore.kernel.org/bpf/20210626181156.1873604-1-rkovhaev@gmail.com
XDP_REDIRECT works by a three-step process: the bpf_redirect() and
bpf_redirect_map() helpers will lookup the target of the redirect and store
it (along with some other metadata) in a per-CPU struct bpf_redirect_info.
Next, when the program returns the XDP_REDIRECT return code, the driver
will call xdp_do_redirect() which will use the information thus stored to
actually enqueue the frame into a bulk queue structure (that differs
slightly by map type, but shares the same principle). Finally, before
exiting its NAPI poll loop, the driver will call xdp_do_flush(), which will
flush all the different bulk queues, thus completing the redirect.
Pointers to the map entries will be kept around for this whole sequence of
steps, protected by RCU. However, there is no top-level rcu_read_lock() in
the core code; instead drivers add their own rcu_read_lock() around the XDP
portions of the code, but somewhat inconsistently as Martin discovered[0].
However, things still work because everything happens inside a single NAPI
poll sequence, which means it's between a pair of calls to
local_bh_disable()/local_bh_enable(). So Paul suggested[1] that we could
document this intention by using rcu_dereference_check() with
rcu_read_lock_bh_held() as a second parameter, thus allowing sparse and
lockdep to verify that everything is done correctly.
This patch does just that: we add an __rcu annotation to the map entry
pointers and remove the various comments explaining the NAPI poll assurance
strewn through devmap.c in favour of a longer explanation in filter.c. The
goal is to have one coherent documentation of the entire flow, and rely on
the RCU annotations as a "standard" way of communicating the flow in the
map code (which can additionally be understood by sparse and lockdep).
The RCU annotation replacements result in a fairly straight-forward
replacement where READ_ONCE() becomes rcu_dereference_check(), WRITE_ONCE()
becomes rcu_assign_pointer() and xchg() and cmpxchg() gets wrapped in the
proper constructs to cast the pointer back and forth between __rcu and
__kernel address space (for the benefit of sparse). The one complication is
that xskmap has a few constructions where double-pointers are passed back
and forth; these simply all gain __rcu annotations, and only the final
reference/dereference to the inner-most pointer gets changed.
With this, everything can be run through sparse without eliciting
complaints, and lockdep can verify correctness even without the use of
rcu_read_lock() in the drivers. Subsequent patches will clean these up from
the drivers.
[0] https://lore.kernel.org/bpf/20210415173551.7ma4slcbqeyiba2r@kafai-mbp.dhcp.thefacebook.com/
[1] https://lore.kernel.org/bpf/20210419165837.GA975577@paulmck-ThinkPad-P17-Gen-1/
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210624160609.292325-6-toke@redhat.com
XDP programs are called from a NAPI poll context, which means the RCU
reference liveness is ensured by local_bh_disable(). Add
rcu_read_lock_bh_held() as a condition to the RCU checks for map lookups so
lockdep understands that the dereferences are safe from inside *either* an
rcu_read_lock() section *or* a local_bh_disable() section. While both
bh_disabled and rcu_read_lock() provide RCU protection, they are
semantically distinct, so we need both conditions to prevent lockdep
complaints.
This change is done in preparation for removing the redundant
rcu_read_lock()s from drivers.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-5-toke@redhat.com
The sub-programs prog->aux->poke_tab[] is populated in jit_subprogs() and
then used when emitting 'BPF_JMP|BPF_TAIL_CALL' insn->code from the
individual JITs. The poke_tab[] to use is stored in the insn->imm by
the code adding it to that array slot. The JIT then uses imm to find the
right entry for an individual instruction. In the x86 bpf_jit_comp.c
this is done by calling emit_bpf_tail_call_direct with the poke_tab[]
of the imm value.
However, we observed the below null-ptr-deref when mixing tail call
programs with subprog programs. For this to happen we just need to
mix bpf-2-bpf calls and tailcalls with some extra calls or instructions
that would be patched later by one of the fixup routines. So whats
happening?
Before the fixup_call_args() -- where the jit op is done -- various
code patching is done by do_misc_fixups(). This may increase the
insn count, for example when we patch map_lookup_up using map_gen_lookup
hook. This does two things. First, it means the instruction index,
insn_idx field, of a tail call instruction will move by a 'delta'.
In verifier code,
struct bpf_jit_poke_descriptor desc = {
.reason = BPF_POKE_REASON_TAIL_CALL,
.tail_call.map = BPF_MAP_PTR(aux->map_ptr_state),
.tail_call.key = bpf_map_key_immediate(aux),
.insn_idx = i + delta,
};
Then subprog start values subprog_info[i].start will be updated
with the delta and any poke descriptor index will also be updated
with the delta in adjust_poke_desc(). If we look at the adjust
subprog starts though we see its only adjusted when the delta
occurs before the new instructions,
/* NOTE: fake 'exit' subprog should be updated as well. */
for (i = 0; i <= env->subprog_cnt; i++) {
if (env->subprog_info[i].start <= off)
continue;
Earlier subprograms are not changed because their start values
are not moved. But, adjust_poke_desc() does the offset + delta
indiscriminately. The result is poke descriptors are potentially
corrupted.
Then in jit_subprogs() we only populate the poke_tab[]
when the above insn_idx is less than the next subprogram start. From
above we corrupted our insn_idx so we might incorrectly assume a
poke descriptor is not used in a subprogram omitting it from the
subprogram. And finally when the jit runs it does the deref of poke_tab
when emitting the instruction and crashes with below. Because earlier
step omitted the poke descriptor.
The fix is straight forward with above context. Simply move same logic
from adjust_subprog_starts() into adjust_poke_descs() and only adjust
insn_idx when needed.
[ 82.396354] bpf_testmod: version magic '5.12.0-rc2alu+ SMP preempt mod_unload ' should be '5.12.0+ SMP preempt mod_unload '
[ 82.623001] loop10: detected capacity change from 0 to 8
[ 88.487424] ==================================================================
[ 88.487438] BUG: KASAN: null-ptr-deref in do_jit+0x184a/0x3290
[ 88.487455] Write of size 8 at addr 0000000000000008 by task test_progs/5295
[ 88.487471] CPU: 7 PID: 5295 Comm: test_progs Tainted: G I 5.12.0+ #386
[ 88.487483] Hardware name: Dell Inc. Precision 5820 Tower/002KVM, BIOS 1.9.2 01/24/2019
[ 88.487490] Call Trace:
[ 88.487498] dump_stack+0x93/0xc2
[ 88.487515] kasan_report.cold+0x5f/0xd8
[ 88.487530] ? do_jit+0x184a/0x3290
[ 88.487542] do_jit+0x184a/0x3290
...
[ 88.487709] bpf_int_jit_compile+0x248/0x810
...
[ 88.487765] bpf_check+0x3718/0x5140
...
[ 88.487920] bpf_prog_load+0xa22/0xf10
Fixes: a748c6975d ("bpf: propagate poke descriptors to subprograms")
Reported-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f9640 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb7 ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
This reverts commit d37300ed18 ("bpf: program: Refuse non-O_RDWR flags
in BPF_OBJ_GET"). It breaks Android userspace which expects to be able to
fetch programs with just read permissions.
See: https://cs.android.com/android/platform/superproject/+/master:frameworks/libs/net/common/native/bpf_syscall_wrappers/include/BpfSyscallWrappers.h;drc=7005c764be23d31fa1d69e826b4a2f6689a8c81e;l=124
Side-note: another option to fix it would be to extend bpf_prog_new_fd()
and to pass in used file mode flags in the same way as we do for maps via
bpf_map_new_fd(). Meaning, they'd end up in anon_inode_getfd() and thus
would be retained for prog fd operations with bpf() syscall. Right now
these flags are not checked with progs since they are immutable for their
lifetime (as opposed to maps which can be updated from user space). In
future this could potentially change with new features, but at that point
it's still fine to do the bpf_prog_new_fd() extension when needed. For a
simple stable fix, a revert is less churn.
Fixes: d37300ed18 ("bpf: program: Refuse non-O_RDWR flags in BPF_OBJ_GET")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
[ Daniel: added side-note to commit message ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Greg Kroah-Hartman <gregkh@google.com>
Link: https://lore.kernel.org/bpf/20210618105526.265003-1-zenczykowski@gmail.com
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-17
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 25 day(s) which contain
a total of 148 files changed, 4779 insertions(+), 1248 deletions(-).
The main changes are:
1) BPF infrastructure to migrate TCP child sockets from a listener to another
in the same reuseport group/map, from Kuniyuki Iwashima.
2) Add a provably sound, faster and more precise algorithm for tnum_mul() as
noted in https://arxiv.org/abs/2105.05398, from Harishankar Vishwanathan.
3) Streamline error reporting changes in libbpf as planned out in the
'libbpf: the road to v1.0' effort, from Andrii Nakryiko.
4) Add broadcast support to xdp_redirect_map(), from Hangbin Liu.
5) Extends bpf_map_lookup_and_delete_elem() functionality to 4 more map
types, that is, {LRU_,PERCPU_,LRU_PERCPU_,}HASH, from Denis Salopek.
6) Support new LLVM relocations in libbpf to make them more linker friendly,
also add a doc to describe the BPF backend relocations, from Yonghong Song.
7) Silence long standing KUBSAN complaints on register-based shifts in
interpreter, from Daniel Borkmann and Eric Biggers.
8) Add dummy PT_REGS macros in libbpf to fail BPF program compilation when
target arch cannot be determined, from Lorenz Bauer.
9) Extend AF_XDP to support large umems with 1M+ pages, from Magnus Karlsson.
10) Fix two minor libbpf tc BPF API issues, from Kumar Kartikeya Dwivedi.
11) Move libbpf BPF_SEQ_PRINTF/BPF_SNPRINTF macros that can be used by BPF
programs to bpf_helpers.h header, from Florent Revest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a shift-out-of-bounds that KUBSAN observed in the
interpreter:
[...]
UBSAN: shift-out-of-bounds in kernel/bpf/core.c:1420:2
shift exponent 255 is too large for 64-bit type 'long long unsigned int'
CPU: 1 PID: 11097 Comm: syz-executor.4 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
___bpf_prog_run.cold+0x19/0x56c kernel/bpf/core.c:1420
__bpf_prog_run32+0x8f/0xd0 kernel/bpf/core.c:1735
bpf_dispatcher_nop_func include/linux/bpf.h:644 [inline]
bpf_prog_run_pin_on_cpu include/linux/filter.h:624 [inline]
bpf_prog_run_clear_cb include/linux/filter.h:755 [inline]
run_filter+0x1a1/0x470 net/packet/af_packet.c:2031
packet_rcv+0x313/0x13e0 net/packet/af_packet.c:2104
dev_queue_xmit_nit+0x7c2/0xa90 net/core/dev.c:2387
xmit_one net/core/dev.c:3588 [inline]
dev_hard_start_xmit+0xad/0x920 net/core/dev.c:3609
__dev_queue_xmit+0x2121/0x2e00 net/core/dev.c:4182
__bpf_tx_skb net/core/filter.c:2116 [inline]
__bpf_redirect_no_mac net/core/filter.c:2141 [inline]
__bpf_redirect+0x548/0xc80 net/core/filter.c:2164
____bpf_clone_redirect net/core/filter.c:2448 [inline]
bpf_clone_redirect+0x2ae/0x420 net/core/filter.c:2420
___bpf_prog_run+0x34e1/0x77d0 kernel/bpf/core.c:1523
__bpf_prog_run512+0x99/0xe0 kernel/bpf/core.c:1737
bpf_dispatcher_nop_func include/linux/bpf.h:644 [inline]
bpf_test_run+0x3ed/0xc50 net/bpf/test_run.c:50
bpf_prog_test_run_skb+0xabc/0x1c50 net/bpf/test_run.c:582
bpf_prog_test_run kernel/bpf/syscall.c:3127 [inline]
__do_sys_bpf+0x1ea9/0x4f00 kernel/bpf/syscall.c:4406
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
[...]
Generally speaking, KUBSAN reports from the kernel should be fixed.
However, in case of BPF, this particular report caused concerns since
the large shift is not wrong from BPF point of view, just undefined.
In the verifier, K-based shifts that are >= {64,32} (depending on the
bitwidth of the instruction) are already rejected. The register-based
cases were not given their content might not be known at verification
time. Ideas such as verifier instruction rewrite with an additional
AND instruction for the source register were brought up, but regularly
rejected due to the additional runtime overhead they incur.
As Edward Cree rightly put it:
Shifts by more than insn bitness are legal in the BPF ISA; they are
implementation-defined behaviour [of the underlying architecture],
rather than UB, and have been made legal for performance reasons.
Each of the JIT backends compiles the BPF shift operations to machine
instructions which produce implementation-defined results in such a
case; the resulting contents of the register may be arbitrary but
program behaviour as a whole remains defined.
Guard checks in the fast path (i.e. affecting JITted code) will thus
not be accepted.
The case of division by zero is not truly analogous here, as division
instructions on many of the JIT-targeted architectures will raise a
machine exception / fault on division by zero, whereas (to the best
of my knowledge) none will do so on an out-of-bounds shift.
Given the KUBSAN report only affects the BPF interpreter, but not JITs,
one solution is to add the ANDs with 63 or 31 into ___bpf_prog_run().
That would make the shifts defined, and thus shuts up KUBSAN, and the
compiler would optimize out the AND on any CPU that interprets the shift
amounts modulo the width anyway (e.g., confirmed from disassembly that
on x86-64 and arm64 the generated interpreter code is the same before
and after this fix).
The BPF interpreter is slow path, and most likely compiled out anyway
as distros select BPF_JIT_ALWAYS_ON to avoid speculative execution of
BPF instructions by the interpreter. Given the main argument was to
avoid sacrificing performance, the fact that the AND is optimized away
from compiler for mainstream archs helps as well as a solution moving
forward. Also add a comment on LSH/RSH/ARSH translation for JIT authors
to provide guidance when they see the ___bpf_prog_run() interpreter
code and use it as a model for a new JIT backend.
Reported-by: syzbot+bed360704c521841c85d@syzkaller.appspotmail.com
Reported-by: Kurt Manucredo <fuzzybritches0@gmail.com>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Co-developed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: syzbot+bed360704c521841c85d@syzkaller.appspotmail.com
Cc: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/bpf/0000000000008f912605bd30d5d7@google.com
Link: https://lore.kernel.org/bpf/bac16d8d-c174-bdc4-91bd-bfa62b410190@gmail.com
This patch introduces a new bpf_attach_type for BPF_PROG_TYPE_SK_REUSEPORT
to check if the attached eBPF program is capable of migrating sockets. When
the eBPF program is attached, we run it for socket migration if the
expected_attach_type is BPF_SK_REUSEPORT_SELECT_OR_MIGRATE or
net.ipv4.tcp_migrate_req is enabled.
Currently, the expected_attach_type is not enforced for the
BPF_PROG_TYPE_SK_REUSEPORT type of program. Thus, this commit follows the
earlier idea in the commit aac3fc320d ("bpf: Post-hooks for sys_bind") to
fix up the zero expected_attach_type in bpf_prog_load_fixup_attach_type().
Moreover, this patch adds a new field (migrating_sk) to sk_reuseport_md to
select a new listener based on the child socket. migrating_sk varies
depending on if it is migrating a request in the accept queue or during
3WHS.
- accept_queue : sock (ESTABLISHED/SYN_RECV)
- 3WHS : request_sock (NEW_SYN_RECV)
In the eBPF program, we can select a new listener by
BPF_FUNC_sk_select_reuseport(). Also, we can cancel migration by returning
SK_DROP. This feature is useful when listeners have different settings at
the socket API level or when we want to free resources as soon as possible.
- SK_PASS with selected_sk, select it as a new listener
- SK_PASS with selected_sk NULL, fallbacks to the random selection
- SK_DROP, cancel the migration.
There is a noteworthy point. We select a listening socket in three places,
but we do not have struct skb at closing a listener or retransmitting a
SYN+ACK. On the other hand, some helper functions do not expect skb is NULL
(e.g. skb_header_pointer() in BPF_FUNC_skb_load_bytes(), skb_tail_pointer()
in BPF_FUNC_skb_load_bytes_relative()). So we allocate an empty skb
temporarily before running the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201123003828.xjpjdtk4ygl6tg6h@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201203042402.6cskdlit5f3mw4ru@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201209030903.hhow5r53l6fmozjn@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-10-kuniyu@amazon.co.jp
The verifier only enumerates valid control-flow paths and skips paths that
are unreachable in the non-speculative domain. And so it can miss issues
under speculative execution on mispredicted branches.
For example, a type confusion has been demonstrated with the following
crafted program:
// r0 = pointer to a map array entry
// r6 = pointer to readable stack slot
// r9 = scalar controlled by attacker
1: r0 = *(u64 *)(r0) // cache miss
2: if r0 != 0x0 goto line 4
3: r6 = r9
4: if r0 != 0x1 goto line 6
5: r9 = *(u8 *)(r6)
6: // leak r9
Since line 3 runs iff r0 == 0 and line 5 runs iff r0 == 1, the verifier
concludes that the pointer dereference on line 5 is safe. But: if the
attacker trains both the branches to fall-through, such that the following
is speculatively executed ...
r6 = r9
r9 = *(u8 *)(r6)
// leak r9
... then the program will dereference an attacker-controlled value and could
leak its content under speculative execution via side-channel. This requires
to mistrain the branch predictor, which can be rather tricky, because the
branches are mutually exclusive. However such training can be done at
congruent addresses in user space using different branches that are not
mutually exclusive. That is, by training branches in user space ...
A: if r0 != 0x0 goto line C
B: ...
C: if r0 != 0x0 goto line D
D: ...
... such that addresses A and C collide to the same CPU branch prediction
entries in the PHT (pattern history table) as those of the BPF program's
lines 2 and 4, respectively. A non-privileged attacker could simply brute
force such collisions in the PHT until observing the attack succeeding.
Alternative methods to mistrain the branch predictor are also possible that
avoid brute forcing the collisions in the PHT. A reliable attack has been
demonstrated, for example, using the following crafted program:
// r0 = pointer to a [control] map array entry
// r7 = *(u64 *)(r0 + 0), training/attack phase
// r8 = *(u64 *)(r0 + 8), oob address
// [...]
// r0 = pointer to a [data] map array entry
1: if r7 == 0x3 goto line 3
2: r8 = r0
// crafted sequence of conditional jumps to separate the conditional
// branch in line 193 from the current execution flow
3: if r0 != 0x0 goto line 5
4: if r0 == 0x0 goto exit
5: if r0 != 0x0 goto line 7
6: if r0 == 0x0 goto exit
[...]
187: if r0 != 0x0 goto line 189
188: if r0 == 0x0 goto exit
// load any slowly-loaded value (due to cache miss in phase 3) ...
189: r3 = *(u64 *)(r0 + 0x1200)
// ... and turn it into known zero for verifier, while preserving slowly-
// loaded dependency when executing:
190: r3 &= 1
191: r3 &= 2
// speculatively bypassed phase dependency
192: r7 += r3
193: if r7 == 0x3 goto exit
194: r4 = *(u8 *)(r8 + 0)
// leak r4
As can be seen, in training phase (phase != 0x3), the condition in line 1
turns into false and therefore r8 with the oob address is overridden with
the valid map value address, which in line 194 we can read out without
issues. However, in attack phase, line 2 is skipped, and due to the cache
miss in line 189 where the map value is (zeroed and later) added to the
phase register, the condition in line 193 takes the fall-through path due
to prior branch predictor training, where under speculation, it'll load the
byte at oob address r8 (unknown scalar type at that point) which could then
be leaked via side-channel.
One way to mitigate these is to 'branch off' an unreachable path, meaning,
the current verification path keeps following the is_branch_taken() path
and we push the other branch to the verification stack. Given this is
unreachable from the non-speculative domain, this branch's vstate is
explicitly marked as speculative. This is needed for two reasons: i) if
this path is solely seen from speculative execution, then we later on still
want the dead code elimination to kick in in order to sanitize these
instructions with jmp-1s, and ii) to ensure that paths walked in the
non-speculative domain are not pruned from earlier walks of paths walked in
the speculative domain. Additionally, for robustness, we mark the registers
which have been part of the conditional as unknown in the speculative path
given there should be no assumptions made on their content.
The fix in here mitigates type confusion attacks described earlier due to
i) all code paths in the BPF program being explored and ii) existing
verifier logic already ensuring that given memory access instruction
references one specific data structure.
An alternative to this fix that has also been looked at in this scope was to
mark aux->alu_state at the jump instruction with a BPF_JMP_TAKEN state as
well as direction encoding (always-goto, always-fallthrough, unknown), such
that mixing of different always-* directions themselves as well as mixing of
always-* with unknown directions would cause a program rejection by the
verifier, e.g. programs with constructs like 'if ([...]) { x = 0; } else
{ x = 1; }' with subsequent 'if (x == 1) { [...] }'. For unprivileged, this
would result in only single direction always-* taken paths, and unknown taken
paths being allowed, such that the former could be patched from a conditional
jump to an unconditional jump (ja). Compared to this approach here, it would
have two downsides: i) valid programs that otherwise are not performing any
pointer arithmetic, etc, would potentially be rejected/broken, and ii) we are
required to turn off path pruning for unprivileged, where both can be avoided
in this work through pushing the invalid branch to the verification stack.
The issue was originally discovered by Adam and Ofek, and later independently
discovered and reported as a result of Benedict and Piotr's research work.
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Reported-by: Adam Morrison <mad@cs.tau.ac.il>
Reported-by: Ofek Kirzner <ofekkir@gmail.com>
Reported-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
... in such circumstances, we do not want to mark the instruction as seen given
the goal is still to jmp-1 rewrite/sanitize dead code, if it is not reachable
from the non-speculative path verification. We do however want to verify it for
safety regardless.
With the patch as-is all the insns that have been marked as seen before the
patch will also be marked as seen after the patch (just with a potentially
different non-zero count). An upcoming patch will also verify paths that are
unreachable in the non-speculative domain, hence this extension is needed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Instead of relying on current env->pass_cnt, use the seen count from the
old aux data in adjust_insn_aux_data(), and expand it to the new range of
patched instructions. This change is valid given we always expand 1:n
with n>=1, so what applies to the old/original instruction needs to apply
for the replacement as well.
Not relying on env->pass_cnt is a prerequisite for a later change where we
want to avoid marking an instruction seen when verified under speculative
execution path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Commit 59438b4647 ("security,lockdown,selinux: implement SELinux lockdown")
added an implementation of the locked_down LSM hook to SELinux, with the aim
to restrict which domains are allowed to perform operations that would breach
lockdown. This is indirectly also getting audit subsystem involved to report
events. The latter is problematic, as reported by Ondrej and Serhei, since it
can bring down the whole system via audit:
1) The audit events that are triggered due to calls to security_locked_down()
can OOM kill a machine, see below details [0].
2) It also seems to be causing a deadlock via avc_has_perm()/slow_avc_audit()
when trying to wake up kauditd, for example, when using trace_sched_switch()
tracepoint, see details in [1]. Triggering this was not via some hypothetical
corner case, but with existing tools like runqlat & runqslower from bcc, for
example, which make use of this tracepoint. Rough call sequence goes like:
rq_lock(rq) -> -------------------------+
trace_sched_switch() -> |
bpf_prog_xyz() -> +-> deadlock
selinux_lockdown() -> |
audit_log_end() -> |
wake_up_interruptible() -> |
try_to_wake_up() -> |
rq_lock(rq) --------------+
What's worse is that the intention of 59438b4647 to further restrict lockdown
settings for specific applications in respect to the global lockdown policy is
completely broken for BPF. The SELinux policy rule for the current lockdown check
looks something like this:
allow <who> <who> : lockdown { <reason> };
However, this doesn't match with the 'current' task where the security_locked_down()
is executed, example: httpd does a syscall. There is a tracing program attached
to the syscall which triggers a BPF program to run, which ends up doing a
bpf_probe_read_kernel{,_str}() helper call. The selinux_lockdown() hook does
the permission check against 'current', that is, httpd in this example. httpd
has literally zero relation to this tracing program, and it would be nonsensical
having to write an SELinux policy rule against httpd to let the tracing helper
pass. The policy in this case needs to be against the entity that is installing
the BPF program. For example, if bpftrace would generate a histogram of syscall
counts by user space application:
bpftrace -e 'tracepoint:raw_syscalls:sys_enter { @[comm] = count(); }'
bpftrace would then go and generate a BPF program from this internally. One way
of doing it [for the sake of the example] could be to call bpf_get_current_task()
helper and then access current->comm via one of bpf_probe_read_kernel{,_str}()
helpers. So the program itself has nothing to do with httpd or any other random
app doing a syscall here. The BPF program _explicitly initiated_ the lockdown
check. The allow/deny policy belongs in the context of bpftrace: meaning, you
want to grant bpftrace access to use these helpers, but other tracers on the
system like my_random_tracer _not_.
Therefore fix all three issues at the same time by taking a completely different
approach for the security_locked_down() hook, that is, move the check into the
program verification phase where we actually retrieve the BPF func proto. This
also reliably gets the task (current) that is trying to install the BPF tracing
program, e.g. bpftrace/bcc/perf/systemtap/etc, and it also fixes the OOM since
we're moving this out of the BPF helper's fast-path which can be called several
millions of times per second.
The check is then also in line with other security_locked_down() hooks in the
system where the enforcement is performed at open/load time, for example,
open_kcore() for /proc/kcore access or module_sig_check() for module signatures
just to pick few random ones. What's out of scope in the fix as well as in
other security_locked_down() hook locations /outside/ of BPF subsystem is that
if the lockdown policy changes on the fly there is no retrospective action.
This requires a different discussion, potentially complex infrastructure, and
it's also not clear whether this can be solved generically. Either way, it is
out of scope for a suitable stable fix which this one is targeting. Note that
the breakage is specifically on 59438b4647 where it started to rely on 'current'
as UAPI behavior, and _not_ earlier infrastructure such as 9d1f8be5cf ("bpf:
Restrict bpf when kernel lockdown is in confidentiality mode").
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1955585, Jakub Hrozek says:
I starting seeing this with F-34. When I run a container that is traced with
BPF to record the syscalls it is doing, auditd is flooded with messages like:
type=AVC msg=audit(1619784520.593:282387): avc: denied { confidentiality }
for pid=476 comm="auditd" lockdown_reason="use of bpf to read kernel RAM"
scontext=system_u:system_r:auditd_t:s0 tcontext=system_u:system_r:auditd_t:s0
tclass=lockdown permissive=0
This seems to be leading to auditd running out of space in the backlog buffer
and eventually OOMs the machine.
[...]
auditd running at 99% CPU presumably processing all the messages, eventually I get:
Apr 30 12:20:42 fedora kernel: audit: backlog limit exceeded
Apr 30 12:20:42 fedora kernel: audit: backlog limit exceeded
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152579 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152626 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152694 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_lost=6878426 audit_rate_limit=0 audit_backlog_limit=64
Apr 30 12:20:45 fedora kernel: oci-seccomp-bpf invoked oom-killer: gfp_mask=0x100cca(GFP_HIGHUSER_MOVABLE), order=0, oom_score_adj=-1000
Apr 30 12:20:45 fedora kernel: CPU: 0 PID: 13284 Comm: oci-seccomp-bpf Not tainted 5.11.12-300.fc34.x86_64 #1
Apr 30 12:20:45 fedora kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
[...]
[1] https://lore.kernel.org/linux-audit/CANYvDQN7H5tVp47fbYcRasv4XF07eUbsDwT_eDCHXJUj43J7jQ@mail.gmail.com/,
Serhei Makarov says:
Upstream kernel 5.11.0-rc7 and later was found to deadlock during a
bpf_probe_read_compat() call within a sched_switch tracepoint. The problem
is reproducible with the reg_alloc3 testcase from SystemTap's BPF backend
testsuite on x86_64 as well as the runqlat, runqslower tools from bcc on
ppc64le. Example stack trace:
[...]
[ 730.868702] stack backtrace:
[ 730.869590] CPU: 1 PID: 701 Comm: in:imjournal Not tainted, 5.12.0-0.rc2.20210309git144c79ef3353.166.fc35.x86_64 #1
[ 730.871605] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
[ 730.873278] Call Trace:
[ 730.873770] dump_stack+0x7f/0xa1
[ 730.874433] check_noncircular+0xdf/0x100
[ 730.875232] __lock_acquire+0x1202/0x1e10
[ 730.876031] ? __lock_acquire+0xfc0/0x1e10
[ 730.876844] lock_acquire+0xc2/0x3a0
[ 730.877551] ? __wake_up_common_lock+0x52/0x90
[ 730.878434] ? lock_acquire+0xc2/0x3a0
[ 730.879186] ? lock_is_held_type+0xa7/0x120
[ 730.880044] ? skb_queue_tail+0x1b/0x50
[ 730.880800] _raw_spin_lock_irqsave+0x4d/0x90
[ 730.881656] ? __wake_up_common_lock+0x52/0x90
[ 730.882532] __wake_up_common_lock+0x52/0x90
[ 730.883375] audit_log_end+0x5b/0x100
[ 730.884104] slow_avc_audit+0x69/0x90
[ 730.884836] avc_has_perm+0x8b/0xb0
[ 730.885532] selinux_lockdown+0xa5/0xd0
[ 730.886297] security_locked_down+0x20/0x40
[ 730.887133] bpf_probe_read_compat+0x66/0xd0
[ 730.887983] bpf_prog_250599c5469ac7b5+0x10f/0x820
[ 730.888917] trace_call_bpf+0xe9/0x240
[ 730.889672] perf_trace_run_bpf_submit+0x4d/0xc0
[ 730.890579] perf_trace_sched_switch+0x142/0x180
[ 730.891485] ? __schedule+0x6d8/0xb20
[ 730.892209] __schedule+0x6d8/0xb20
[ 730.892899] schedule+0x5b/0xc0
[ 730.893522] exit_to_user_mode_prepare+0x11d/0x240
[ 730.894457] syscall_exit_to_user_mode+0x27/0x70
[ 730.895361] entry_SYSCALL_64_after_hwframe+0x44/0xae
[...]
Fixes: 59438b4647 ("security,lockdown,selinux: implement SELinux lockdown")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Reported-by: Jakub Hrozek <jhrozek@redhat.com>
Reported-by: Serhei Makarov <smakarov@redhat.com>
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: James Morris <jamorris@linux.microsoft.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Frank Eigler <fche@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/bpf/01135120-8bf7-df2e-cff0-1d73f1f841c3@iogearbox.net
This patch introduces a new algorithm for multiplication of tristate
numbers (tnums) that is provably sound. It is faster and more precise when
compared to the existing method.
Like the existing method, this new algorithm follows the long
multiplication algorithm. The idea is to generate partial products by
multiplying each bit in the multiplier (tnum a) with the multiplicand
(tnum b), and adding the partial products after appropriately bit-shifting
them. The new algorithm, however, uses just a single loop over the bits of
the multiplier (tnum a) and accumulates only the uncertain components of
the multiplicand (tnum b) into a mask-only tnum. The following paper
explains the algorithm in more detail: https://arxiv.org/abs/2105.05398.
A natural way to construct the tnum product is by performing a tnum
addition on all the partial products. This algorithm presents another
method of doing this: decompose each partial product into two tnums,
consisting of the values and the masks separately. The mask-sum is
accumulated within the loop in acc_m. The value-sum tnum is generated
using a.value * b.value. The tnum constructed by tnum addition of the
value-sum and the mask-sum contains all possible summations of concrete
values drawn from the partial product tnums pairwise. We prove this result
in the paper.
Our evaluations show that the new algorithm is overall more precise
(producing tnums with less uncertain components) than the existing method.
As an illustrative example, consider the input tnums A and B. The numbers
in the parenthesis correspond to (value;mask).
A = 000000x1 (1;2)
B = 0010011x (38;1)
A * B (existing) = xxxxxxxx (0;255)
A * B (new) = 0x1xxxxx (32;95)
Importantly, we present a proof of soundness of the new algorithm in the
aforementioned paper. Additionally, we show that this new algorithm is
empirically faster than the existing method.
Co-developed-by: Matan Shachnai <m.shachnai@rutgers.edu>
Co-developed-by: Srinivas Narayana <srinivas.narayana@rutgers.edu>
Co-developed-by: Santosh Nagarakatte <santosh.nagarakatte@rutgers.edu>
Signed-off-by: Matan Shachnai <m.shachnai@rutgers.edu>
Signed-off-by: Srinivas Narayana <srinivas.narayana@rutgers.edu>
Signed-off-by: Santosh Nagarakatte <santosh.nagarakatte@rutgers.edu>
Signed-off-by: Harishankar Vishwanathan <harishankar.vishwanathan@rutgers.edu>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://arxiv.org/abs/2105.05398
Link: https://lore.kernel.org/bpf/20210531020157.7386-1-harishankar.vishwanathan@rutgers.edu
As Colin pointed out, the first drops assignment after declaration will
be overwritten by the second drops assignment before using, which makes
it useless.
Since the drops variable will be used only once. Just remove it and
use "cnt - sent" in trace_xdp_devmap_xmit().
Fixes: cb261b594b ("bpf: Run devmap xdp_prog on flush instead of bulk enqueue")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210528024356.24333-1-liuhangbin@gmail.com
These macros are convenient wrappers around the bpf_seq_printf and
bpf_snprintf helpers. They are currently provided by bpf_tracing.h which
targets low level tracing primitives. bpf_helpers.h is a better fit.
The __bpf_narg and __bpf_apply are needed in both files and provided
twice. __bpf_empty isn't used anywhere and is removed from bpf_tracing.h
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210526164643.2881368-1-revest@chromium.org
This patch adds two flags BPF_F_BROADCAST and BPF_F_EXCLUDE_INGRESS to
extend xdp_redirect_map for broadcast support.
With BPF_F_BROADCAST the packet will be broadcasted to all the interfaces
in the map. with BPF_F_EXCLUDE_INGRESS the ingress interface will be
excluded when do broadcasting.
When getting the devices in dev hash map via dev_map_hash_get_next_key(),
there is a possibility that we fall back to the first key when a device
was removed. This will duplicate packets on some interfaces. So just walk
the whole buckets to avoid this issue. For dev array map, we also walk the
whole map to find valid interfaces.
Function bpf_clear_redirect_map() was removed in
commit ee75aef23a ("bpf, xdp: Restructure redirect actions").
Add it back as we need to use ri->map again.
With test topology:
+-------------------+ +-------------------+
| Host A (i40e 10G) | ---------- | eno1(i40e 10G) |
+-------------------+ | |
| Host B |
+-------------------+ | |
| Host C (i40e 10G) | ---------- | eno2(i40e 10G) |
+-------------------+ | |
| +------+ |
| veth0 -- | Peer | |
| veth1 -- | | |
| veth2 -- | NS | |
| +------+ |
+-------------------+
On Host A:
# pktgen/pktgen_sample03_burst_single_flow.sh -i eno1 -d $dst_ip -m $dst_mac -s 64
On Host B(Intel(R) Xeon(R) CPU E5-2690 v3 @ 2.60GHz, 128G Memory):
Use xdp_redirect_map and xdp_redirect_map_multi in samples/bpf for testing.
All the veth peers in the NS have a XDP_DROP program loaded. The
forward_map max_entries in xdp_redirect_map_multi is modify to 4.
Testing the performance impact on the regular xdp_redirect path with and
without patch (to check impact of additional check for broadcast mode):
5.12 rc4 | redirect_map i40e->i40e | 2.0M | 9.7M
5.12 rc4 | redirect_map i40e->veth | 1.7M | 11.8M
5.12 rc4 + patch | redirect_map i40e->i40e | 2.0M | 9.6M
5.12 rc4 + patch | redirect_map i40e->veth | 1.7M | 11.7M
Testing the performance when cloning packets with the redirect_map_multi
test, using a redirect map size of 4, filled with 1-3 devices:
5.12 rc4 + patch | redirect_map multi i40e->veth (x1) | 1.7M | 11.4M
5.12 rc4 + patch | redirect_map multi i40e->veth (x2) | 1.1M | 4.3M
5.12 rc4 + patch | redirect_map multi i40e->veth (x3) | 0.8M | 2.6M
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/20210519090747.1655268-3-liuhangbin@gmail.com
This changes the devmap XDP program support to run the program when the
bulk queue is flushed instead of before the frame is enqueued. This has
a couple of benefits:
- It "sorts" the packets by destination devmap entry, and then runs the
same BPF program on all the packets in sequence. This ensures that we
keep the XDP program and destination device properties hot in I-cache.
- It makes the multicast implementation simpler because it can just
enqueue packets using bq_enqueue() without having to deal with the
devmap program at all.
The drawback is that if the devmap program drops the packet, the enqueue
step is redundant. However, arguably this is mostly visible in a
micro-benchmark, and with more mixed traffic the I-cache benefit should
win out. The performance impact of just this patch is as follows:
Using 2 10Gb i40e NIC, redirecting one to another, or into a veth interface,
which do XDP_DROP on veth peer. With xdp_redirect_map in sample/bpf, send
pkts via pktgen cmd:
./pktgen_sample03_burst_single_flow.sh -i eno1 -d $dst_ip -m $dst_mac -t 10 -s 64
There are about +/- 0.1M deviation for native testing, the performance
improved for the base-case, but some drop back with xdp devmap prog attached.
Version | Test | Generic | Native | Native + 2nd xdp_prog
5.12 rc4 | xdp_redirect_map i40e->i40e | 1.9M | 9.6M | 8.4M
5.12 rc4 | xdp_redirect_map i40e->veth | 1.7M | 11.7M | 9.8M
5.12 rc4 + patch | xdp_redirect_map i40e->i40e | 1.9M | 9.8M | 8.0M
5.12 rc4 + patch | xdp_redirect_map i40e->veth | 1.7M | 12.0M | 9.4M
When bq_xmit_all() is called from bq_enqueue(), another packet will
always be enqueued immediately after, so clearing dev_rx, xdp_prog and
flush_node in bq_xmit_all() is redundant. Move the clear to __dev_flush(),
and only check them once in bq_enqueue() since they are all modified
together.
This change also has the side effect of extending the lifetime of the
RCU-protected xdp_prog that lives inside the devmap entries: Instead of
just living for the duration of the XDP program invocation, the
reference now lives all the way until the bq is flushed. This is safe
because the bq flush happens at the end of the NAPI poll loop, so
everything happens between a local_bh_disable()/local_bh_enable() pair.
However, this is by no means obvious from looking at the call sites; in
particular, some drivers have an additional rcu_read_lock() around only
the XDP program invocation, which only confuses matters further.
Cleaning this up will be done in a separate patch series.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210519090747.1655268-2-liuhangbin@gmail.com
In 801c6058d1 ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.
Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.
Fixes: 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask")
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Similarly as 6bdacdb48e ("bpf: Fix BPF_JIT kconfig symbol dependency") we
need to detangle the hard BPF_LSM dependency on NET. This was previously
implicit by its dependency on BPF_JIT which itself was dependent on NET (but
without any actual/real hard dependency code-wise). Given the latter was
lifted, so should be the former as BPF_LSMs could well exist on net-less
systems. This therefore also fixes a randconfig build error recently reported
by Randy:
ld: kernel/bpf/bpf_lsm.o: in function `bpf_lsm_func_proto':
bpf_lsm.c:(.text+0x1a0): undefined reference to `bpf_sk_storage_get_proto'
ld: bpf_lsm.c:(.text+0x1b8): undefined reference to `bpf_sk_storage_delete_proto'
[...]
Fixes: b24abcff91 ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Fix some spelling mistakes in comments:
aother ==> another
Netiher ==> Neither
desribe ==> describe
intializing ==> initializing
funciton ==> function
wont ==> won't and move the word 'the' at the end to the next line
accross ==> across
pathes ==> paths
triggerred ==> triggered
excute ==> execute
ether ==> either
conervative ==> conservative
convetion ==> convention
markes ==> marks
interpeter ==> interpreter
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210525025659.8898-2-thunder.leizhen@huawei.com
Extend the existing bpf_map_lookup_and_delete_elem() functionality to
hashtab map types, in addition to stacks and queues.
Create a new hashtab bpf_map_ops function that does lookup and deletion
of the element under the same bucket lock and add the created map_ops to
bpf.h.
Signed-off-by: Denis Salopek <denis.salopek@sartura.hr>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/4d18480a3e990ffbf14751ddef0325eed3be2966.1620763117.git.denis.salopek@sartura.hr
Commit 4976b718c3 ("bpf: Introduce pseudo_btf_id") switched the
order of resolve_pseudo_ldimm(), in which some pseudo instructions
are rewritten. Thus those rewritten instructions cannot be passed
to driver via 'prepare' offload callback.
Reorder the 'prepare' offload callback to fix it.
Fixes: 4976b718c3 ("bpf: Introduce pseudo_btf_id")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210520085834.15023-1-simon.horman@netronome.com
The cppcheck static code analysis reported the following error:
if (WARN_ON_ONCE(nest_level > ARRAY_SIZE(bufs->tmp_bufs))) {
^
ARRAY_SIZE is a macro that expands to sizeofs, so bufs is not actually
dereferenced at runtime, and the code is actually safe. But to keep
things tidy, this patch removes the need for a call to ARRAY_SIZE by
extracting the size of the array into a macro. Cppcheck should no longer
be confused and the code ends up being a bit cleaner.
Fixes: e2d5b2bb76 ("bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20210517092830.1026418-2-revest@chromium.org
The per-cpu buffers contain bprintf data rather than printf arguments.
The macro name and comment were a bit confusing, this rewords them in a
clearer way.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20210517092830.1026418-1-revest@chromium.org
Randy reported a randconfig build error recently on i386:
ld: arch/x86/net/bpf_jit_comp32.o: in function `do_jit':
bpf_jit_comp32.c:(.text+0x28c9): undefined reference to `__bpf_call_base'
ld: arch/x86/net/bpf_jit_comp32.o: in function `bpf_int_jit_compile':
bpf_jit_comp32.c:(.text+0x3694): undefined reference to `bpf_jit_blind_constants'
ld: bpf_jit_comp32.c:(.text+0x3719): undefined reference to `bpf_jit_binary_free'
ld: bpf_jit_comp32.c:(.text+0x3745): undefined reference to `bpf_jit_binary_alloc'
ld: bpf_jit_comp32.c:(.text+0x37d3): undefined reference to `bpf_jit_prog_release_other'
[...]
The cause was that b24abcff91 ("bpf, kconfig: Add consolidated menu entry for
bpf with core options") moved BPF_JIT from net/Kconfig into kernel/bpf/Kconfig
and previously BPF_JIT was guarded by a 'if NET'. However, there is no actual
dependency on NET, it's just that menuconfig NET selects BPF. And the latter in
turn causes kernel/bpf/core.o to be built which contains above symbols. Randy's
randconfig didn't have NET set, and BPF wasn't either, but BPF_JIT otoh was.
Detangle this by making BPF_JIT depend on BPF instead. arm64 was the only arch
that pulled in its JIT in net/ via obj-$(CONFIG_NET), all others unconditionally
pull this dir in via obj-y. Do the same since CONFIG_NET guard there is really
useless as we compiled the JIT via obj-$(CONFIG_BPF_JIT) += bpf_jit_comp.o anyway.
Fixes: b24abcff91 ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
The sparse tool complains as follows:
kernel/bpf/syscall.c:4567:29: warning:
symbol 'bpf_sys_bpf_proto' was not declared. Should it be static?
kernel/bpf/syscall.c:4592:29: warning:
symbol 'bpf_sys_close_proto' was not declared. Should it be static?
This symbol is not used outside of syscall.c, so marks it static.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210519064116.240536-1-pulehui@huawei.com
Add bpf_sys_close() helper to be used by the syscall/loader program to close
intermediate FDs and other cleanup.
Note this helper must never be allowed inside fdget/fdput bracketing.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-11-alexei.starovoitov@gmail.com
Add new helper:
long bpf_btf_find_by_name_kind(char *name, int name_sz, u32 kind, int flags)
Description
Find BTF type with given name and kind in vmlinux BTF or in module's BTFs.
Return
Returns btf_id and btf_obj_fd in lower and upper 32 bits.
It will be used by loader program to find btf_id to attach the program to
and to find btf_ids of ksyms.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-10-alexei.starovoitov@gmail.com
Typical program loading sequence involves creating bpf maps and applying
map FDs into bpf instructions in various places in the bpf program.
This job is done by libbpf that is using compiler generated ELF relocations
to patch certain instruction after maps are created and BTFs are loaded.
The goal of fd_idx is to allow bpf instructions to stay immutable
after compilation. At load time the libbpf would still create maps as usual,
but it wouldn't need to patch instructions. It would store map_fds into
__u32 fd_array[] and would pass that pointer to sys_bpf(BPF_PROG_LOAD).
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-9-alexei.starovoitov@gmail.com
Similar to prog_load make btf_load command to be availble to
bpf_prog_type_syscall program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-7-alexei.starovoitov@gmail.com
With the help from bpfptr_t prepare relevant bpf syscall commands
to be used from kernel and user space.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-4-alexei.starovoitov@gmail.com
Add placeholders for bpf_sys_bpf() helper and new program type.
Make sure to check that expected_attach_type is zero for future extensibility.
Allow tracing helper functions to be used in this program type, since they will
only execute from user context via bpf_prog_test_run.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-2-alexei.starovoitov@gmail.com
The bpf_seq_printf, bpf_trace_printk and bpf_snprintf helpers share one
per-cpu buffer that they use to store temporary data (arguments to
bprintf). They "get" that buffer with try_get_fmt_tmp_buf and "put" it
by the end of their scope with bpf_bprintf_cleanup.
If one of these helpers gets called within the scope of one of these
helpers, for example: a first bpf program gets called, uses
bpf_trace_printk which calls raw_spin_lock_irqsave which is traced by
another bpf program that calls bpf_snprintf, then the second "get"
fails. Essentially, these helpers are not re-entrant. They would return
-EBUSY and print a warning message once.
This patch triples the number of bprintf buffers to allow three levels
of nesting. This is very similar to what was done for tracepoints in
"9594dc3c7e7 bpf: fix nested bpf tracepoints with per-cpu data"
Fixes: d9c9e4db18 ("bpf: Factorize bpf_trace_printk and bpf_seq_printf")
Reported-by: syzbot+63122d0bc347f18c1884@syzkaller.appspotmail.com
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210511081054.2125874-1-revest@chromium.org
The recursion check in __bpf_prog_enter and __bpf_prog_exit
leaves some (not inlined) functions unprotected:
In __bpf_prog_enter:
- migrate_disable is called before prog->active is checked
In __bpf_prog_exit:
- migrate_enable,rcu_read_unlock_strict are called after
prog->active is decreased
When attaching trampoline to them we get panic like:
traps: PANIC: double fault, error_code: 0x0
double fault: 0000 [#1] SMP PTI
RIP: 0010:__bpf_prog_enter+0x4/0x50
...
Call Trace:
<IRQ>
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
...
Fixing this by adding deny list of btf ids for tracing
programs and checking btf id during program verification.
Adding above functions to this list.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210429114712.43783-1-jolsa@kernel.org
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
Right now, all core BPF related options are scattered in different Kconfig
locations mainly due to historic reasons. Moving forward, lets add a proper
subsystem entry under ...
General setup --->
BPF subsystem --->
... in order to have all knobs in a single location and thus ease BPF related
configuration. Networking related bits such as sockmap are out of scope for
the general setup and therefore better suited to remain in net/Kconfig.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/f23f58765a4d59244ebd8037da7b6a6b2fb58446.1620765074.git.daniel@iogearbox.net
Only the very first page of BPF ringbuf that contains consumer position
counter is supposed to be mapped as writeable by user-space. Producer
position is read-only and can be modified only by the kernel code. BPF ringbuf
data pages are read-only as well and are not meant to be modified by
user-code to maintain integrity of per-record headers.
This patch allows to map only consumer position page as writeable and
everything else is restricted to be read-only. remap_vmalloc_range()
internally adds VM_DONTEXPAND, so all the established memory mappings can't be
extended, which prevents any future violations through mremap()'ing.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
A BPF program might try to reserve a buffer larger than the ringbuf size.
If the consumer pointer is way ahead of the producer, that would be
successfully reserved, allowing the BPF program to read or write out of
the ringbuf allocated area.
Reported-by: Ryota Shiga (Flatt Security)
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Fix a bug in the verifier's scalar32_min_max_*() functions which leads to
incorrect tracking of 32 bit bounds for the simulation of and/or/xor bitops.
When both the src & dst subreg is a known constant, then the assumption is
that scalar_min_max_*() will take care to update bounds correctly. However,
this is not the case, for example, consider a register R2 which has a tnum
of 0xffffffff00000000, meaning, lower 32 bits are known constant and in this
case of value 0x00000001. R2 is then and'ed with a register R3 which is a
64 bit known constant, here, 0x100000002.
What can be seen in line '10:' is that 32 bit bounds reach an invalid state
where {u,s}32_min_value > {u,s}32_max_value. The reason is scalar32_min_max_*()
delegates 32 bit bounds updates to scalar_min_max_*(), however, that really
only takes place when both the 64 bit src & dst register is a known constant.
Given scalar32_min_max_*() is intended to be designed as closely as possible
to scalar_min_max_*(), update the 32 bit bounds in this situation through
__mark_reg32_known() which will set all {u,s}32_{min,max}_value to the correct
constant, which is 0x00000000 after the fix (given 0x00000001 & 0x00000002 in
32 bit space). This is possible given var32_off already holds the final value
as dst_reg->var_off is updated before calling scalar32_min_max_*().
Before fix, invalid tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=1,s32_max_value=0,u32_min_value=1,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
After fix, correct tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=0,s32_max_value=0,u32_min_value=0,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes: 2921c90d47 ("bpf: Fix a verifier failure with xor")
Reported-by: Manfred Paul (@_manfp)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
func_states_equal makes a very short lived allocation for idmap,
probably because it's too large to fit on the stack. However the
function is called quite often, leading to a lot of alloc / free
churn. Replace the temporary allocation with dedicated scratch
space in struct bpf_verifier_env.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/bpf/20210429134656.122225-4-lmb@cloudflare.com
Resizing and copying stack and reference tracking state currently
does a lot of kfree / kmalloc when the size of the tracked set changes.
The logic in copy_*_state and realloc_*_state is also hard to follow.
Refactor this into two core functions. copy_array copies from a source
into a destination. It avoids reallocation by taking the allocated
size of the destination into account via ksize(). The function is
essentially krealloc_array, with the difference that the contents of
dst are not preserved. realloc_array changes the size of an array and
zeroes newly allocated items. Contrary to krealloc both functions don't
free the destination if the size is zero. Instead we rely on free_func_state
to clean up.
realloc_stack_state is renamed to grow_stack_state to better convey
that it never shrinks the stack state.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210429134656.122225-2-lmb@cloudflare.com
We can't currently allow to attach functions with variable arguments.
The problem is that we should save all the registers for arguments,
which is probably doable, but if caller uses more than 6 arguments,
we need stack data, which will be wrong, because of the extra stack
frame we do in bpf trampoline, so we could crash.
Also currently there's malformed trampoline code generated for such
functions at the moment as described in:
https://lore.kernel.org/bpf/20210429212834.82621-1-jolsa@kernel.org/
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210505132529.401047-1-jolsa@kernel.org
The current implemented mechanisms to mitigate data disclosure under
speculation mainly address stack and map value oob access from the
speculative domain. However, Piotr discovered that uninitialized BPF
stack is not protected yet, and thus old data from the kernel stack,
potentially including addresses of kernel structures, could still be
extracted from that 512 bytes large window. The BPF stack is special
compared to map values since it's not zero initialized for every
program invocation, whereas map values /are/ zero initialized upon
their initial allocation and thus cannot leak any prior data in either
domain. In the non-speculative domain, the verifier ensures that every
stack slot read must have a prior stack slot write by the BPF program
to avoid such data leaking issue.
However, this is not enough: for example, when the pointer arithmetic
operation moves the stack pointer from the last valid stack offset to
the first valid offset, the sanitation logic allows for any intermediate
offsets during speculative execution, which could then be used to
extract any restricted stack content via side-channel.
Given for unprivileged stack pointer arithmetic the use of unknown
but bounded scalars is generally forbidden, we can simply turn the
register-based arithmetic operation into an immediate-based arithmetic
operation without the need for masking. This also gives the benefit
of reducing the needed instructions for the operation. Given after
the work in 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic
mask"), the aux->alu_limit already holds the final immediate value for
the offset register with the known scalar. Thus, a simple mov of the
immediate to AX register with using AX as the source for the original
instruction is sufficient and possible now in this case.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The negation logic for the case where the off_reg is sitting in the
dst register is not correct given then we cannot just invert the add
to a sub or vice versa. As a fix, perform the final bitwise and-op
unconditionally into AX from the off_reg, then move the pointer from
the src to dst and finally use AX as the source for the original
pointer arithmetic operation such that the inversion yields a correct
result. The single non-AX mov in between is possible given constant
blinding is retaining it as it's not an immediate based operation.
Fixes: 979d63d50c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Uses the already in-place infrastructure provided by the
'generic_map_*_batch' functions.
No tweak was needed as it transparently handles the percpu variant.
As arrays don't have delete operations, let it return a error to
user space (default behaviour).
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210424214510.806627-2-pctammela@mojatatu.com
BPF has three formatted output helpers: bpf_trace_printk, bpf_seq_printf
and bpf_snprintf. Their signatures specify that all arguments are
provided from the BPF world as u64s (in an array or as registers). All
of these helpers are currently implemented by calling functions such as
snprintf() whose signatures take a variable number of arguments, then
placed in a va_list by the compiler to call vsnprintf().
"d9c9e4db bpf: Factorize bpf_trace_printk and bpf_seq_printf" introduced
a bpf_printf_prepare function that fills an array of u64 sanitized
arguments with an array of "modifiers" which indicate what the "real"
size of each argument should be (given by the format specifier). The
BPF_CAST_FMT_ARG macro consumes these arrays and casts each argument to
its real size. However, the C promotion rules implicitely cast them all
back to u64s. Therefore, the arguments given to snprintf are u64s and
the va_list constructed by the compiler will use 64 bits for each
argument. On 64 bit machines, this happens to work well because 32 bit
arguments in va_lists need to occupy 64 bits anyway, but on 32 bit
architectures this breaks the layout of the va_list expected by the
called function and mangles values.
In "88a5c690b6 bpf: fix bpf_trace_printk on 32 bit archs", this problem
had been solved for bpf_trace_printk only with a "horrid workaround"
that emitted multiple calls to trace_printk where each call had
different argument types and generated different va_list layouts. One of
the call would be dynamically chosen at runtime. This was ok with the 3
arguments that bpf_trace_printk takes but bpf_seq_printf and
bpf_snprintf accept up to 12 arguments. Because this approach scales
code exponentially, it is not a viable option anymore.
Because the promotion rules are part of the language and because the
construction of a va_list is an arch-specific ABI, it's best to just
avoid variadic arguments and va_lists altogether. Thankfully the
kernel's snprintf() has an alternative in the form of bstr_printf() that
accepts arguments in a "binary buffer representation". These binary
buffers are currently created by vbin_printf and used in the tracing
subsystem to split the cost of printing into two parts: a fast one that
only dereferences and remembers values, and a slower one, called later,
that does the pretty-printing.
This patch refactors bpf_printf_prepare to construct binary buffers of
arguments consumable by bstr_printf() instead of arrays of arguments and
modifiers. This gets rid of BPF_CAST_FMT_ARG and greatly simplifies the
bpf_printf_prepare usage but there are a few gotchas that change how
bpf_printf_prepare needs to do things.
Currently, bpf_printf_prepare uses a per cpu temporary buffer as a
generic storage for strings and IP addresses. With this refactoring, the
temporary buffers now holds all the arguments in a structured binary
format.
To comply with the format expected by bstr_printf, certain format
specifiers also need to be pre-formatted: %pB and %pi6/%pi4/%pI4/%pI6.
Because vsnprintf subroutines for these specifiers are hard to expose,
we pre-format these arguments with calls to snprintf().
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210427174313.860948-3-revest@chromium.org
-----BEGIN PGP SIGNATURE-----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=HTEy
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20210426' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
- Add support for measuring the SELinux state and policy capabilities
using IMA.
- A handful of SELinux/NFS patches to compare the SELinux state of one
mount with a set of mount options. Olga goes into more detail in the
patch descriptions, but this is important as it allows more
flexibility when using NFS and SELinux context mounts.
- Properly differentiate between the subjective and objective LSM
credentials; including support for the SELinux and Smack. My clumsy
attempt at a proper fix for AppArmor didn't quite pass muster so John
is working on a proper AppArmor patch, in the meantime this set of
patches shouldn't change the behavior of AppArmor in any way. This
change explains the bulk of the diffstat beyond security/.
- Fix a problem where we were not properly terminating the permission
list for two SELinux object classes.
* tag 'selinux-pr-20210426' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: add proper NULL termination to the secclass_map permissions
smack: differentiate between subjective and objective task credentials
selinux: clarify task subjective and objective credentials
lsm: separate security_task_getsecid() into subjective and objective variants
nfs: account for selinux security context when deciding to share superblock
nfs: remove unneeded null check in nfs_fill_super()
lsm,selinux: add new hook to compare new mount to an existing mount
selinux: fix misspellings using codespell tool
selinux: fix misspellings using codespell tool
selinux: measure state and policy capabilities
selinux: Allow context mounts for unpriviliged overlayfs
Rely on netif_receive_skb_list routine to send skbs converted from
xdp_frames in cpu_map_kthread_run in order to improve i-cache usage.
The proposed patch has been tested running xdp_redirect_cpu bpf sample
available in the kernel tree that is used to redirect UDP frames from
ixgbe driver to a cpumap entry and then to the networking stack. UDP
frames are generated using pktgen. Packets are discarded by the UDP
layer.
$ xdp_redirect_cpu --cpu <cpu> --progname xdp_cpu_map0 --dev <eth>
bpf-next: ~2.35Mpps
bpf-next + cpumap skb-list: ~2.72Mpps
Rename drops counter in kmem_alloc_drops since now it reports just
kmem_cache_alloc_bulk failures
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/c729f83e5d7482d9329e0f165bdbe5adcefd1510.1619169700.git.lorenzo@kernel.org
Similarly as b02709587e ("bpf: Fix propagation of 32-bit signed bounds
from 64-bit bounds."), we also need to fix the propagation of 32 bit
unsigned bounds from 64 bit counterparts. That is, really only set the
u32_{min,max}_value when /both/ {umin,umax}_value safely fit in 32 bit
space. For example, the register with a umin_value == 1 does /not/ imply
that u32_min_value is also equal to 1, since umax_value could be much
larger than 32 bit subregister can hold, and thus u32_min_value is in
the interval [0,1] instead.
Before fix, invalid tracking result of R2_w=inv1:
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smin_value=-9223372036854775807,smax_value=9223372032559808513,umin_value=1,umax_value=18446744069414584321,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv1 R10=fp0
[...]
After fix, correct tracking result of R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)):
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smax_value=9223372032559808513,umax_value=18446744069414584321,var_off=(0x0; 0xffffffff00000001),s32_min_value=0,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)) R10=fp0
[...]
Thus, same issue as in b02709587e holds for unsigned subregister tracking.
Also, align __reg64_bound_u32() similarly to __reg64_bound_s32() as done in
b02709587e to make them uniform again.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Manfred Paul (@_manfp)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Currently we don't allow re-attaching of trampolines. Once
it's detached, it can't be re-attach even when the program
is still loaded.
Adding the possibility to re-attach the loaded tracing and
lsm programs.
Fixing missing unlock with proper cleanup goto jump reported
by Julia.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210414195147.1624932-2-jolsa@kernel.org
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-04-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 69 non-merge commits during the last 22 day(s) which contain
a total of 69 files changed, 3141 insertions(+), 866 deletions(-).
The main changes are:
1) Add BPF static linker support for extern resolution of global, from Andrii.
2) Refine retval for bpf_get_task_stack helper, from Dave.
3) Add a bpf_snprintf helper, from Florent.
4) A bunch of miscellaneous improvements from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
reg->type is enforced by check_reg_type() and map should never be NULL
(it would already have been dereferenced anyway) so these checks are
unnecessary.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-3-revest@chromium.org
In check_bpf_snprintf_call(), a map_direct_value_addr() of the fmt map
should never fail because it has already been checked by
ARG_PTR_TO_CONST_STR. But if it ever fails, it's better to error out
with an explicit debug message rather than silently fail.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-2-revest@chromium.org
Verifier can constrain the min/max bounds of bpf_get_task_stack's return
value more tightly than the default tnum_unknown. Like bpf_get_stack,
return value is num bytes written into a caller-supplied buf, or error,
so do_refine_retval_range will work.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210416204704.2816874-2-davemarchevsky@fb.com
The implementation takes inspiration from the existing bpf_trace_printk
helper but there are a few differences:
To allow for a large number of format-specifiers, parameters are
provided in an array, like in bpf_seq_printf.
Because the output string takes two arguments and the array of
parameters also takes two arguments, the format string needs to fit in
one argument. Thankfully, ARG_PTR_TO_CONST_STR is guaranteed to point to
a zero-terminated read-only map so we don't need a format string length
arg.
Because the format-string is known at verification time, we also do
a first pass of format string validation in the verifier logic. This
makes debugging easier.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-4-revest@chromium.org
This type provides the guarantee that an argument is going to be a const
pointer to somewhere in a read-only map value. It also checks that this
pointer is followed by a zero character before the end of the map value.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-3-revest@chromium.org
Two helpers (trace_printk and seq_printf) have very similar
implementations of format string parsing and a third one is coming
(snprintf). To avoid code duplication and make the code easier to
maintain, this moves the operations associated with format string
parsing (validation and argument sanitization) into one generic
function.
The implementation of the two existing helpers already drifted quite a
bit so unifying them entailed a lot of changes:
- bpf_trace_printk always expected fmt[fmt_size] to be the terminating
NULL character, this is no longer true, the first 0 is terminating.
- bpf_trace_printk now supports %% (which produces the percentage char).
- bpf_trace_printk now skips width formating fields.
- bpf_trace_printk now supports the X modifier (capital hexadecimal).
- bpf_trace_printk now supports %pK, %px, %pB, %pi4, %pI4, %pi6 and %pI6
- argument casting on 32 bit has been simplified into one macro and
using an enum instead of obscure int increments.
- bpf_seq_printf now uses bpf_trace_copy_string instead of
strncpy_from_kernel_nofault and handles the %pks %pus specifiers.
- bpf_seq_printf now prints longs correctly on 32 bit architectures.
- both were changed to use a global per-cpu tmp buffer instead of one
stack buffer for trace_printk and 6 small buffers for seq_printf.
- to avoid per-cpu buffer usage conflict, these helpers disable
preemption while the per-cpu buffer is in use.
- both helpers now support the %ps and %pS specifiers to print symbols.
The implementation is also moved from bpf_trace.c to helpers.c because
the upcoming bpf_snprintf helper will be made available to all BPF
programs and will need it.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-2-revest@chromium.org
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This work tightens the offset mask we use for unprivileged pointer arithmetic
in order to mitigate a corner case reported by Piotr and Benedict where in
the speculative domain it is possible to advance, for example, the map value
pointer by up to value_size-1 out-of-bounds in order to leak kernel memory
via side-channel to user space.
Before this change, the computed ptr_limit for retrieve_ptr_limit() helper
represents largest valid distance when moving pointer to the right or left
which is then fed as aux->alu_limit to generate masking instructions against
the offset register. After the change, the derived aux->alu_limit represents
the largest potential value of the offset register which we mask against which
is just a narrower subset of the former limit.
For minimal complexity, we call sanitize_ptr_alu() from 2 observation points
in adjust_ptr_min_max_vals(), that is, before and after the simulated alu
operation. In the first step, we retieve the alu_state and alu_limit before
the operation as well as we branch-off a verifier path and push it to the
verification stack as we did before which checks the dst_reg under truncation,
in other words, when the speculative domain would attempt to move the pointer
out-of-bounds.
In the second step, we retrieve the new alu_limit and calculate the absolute
distance between both. Moreover, we commit the alu_state and final alu_limit
via update_alu_sanitation_state() to the env's instruction aux data, and bail
out from there if there is a mismatch due to coming from different verification
paths with different states.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Reported-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Benedict Schlueter <benedict.schlueter@rub.de>
Add a small sanitize_needed() helper function and move sanitize_val_alu()
out of the main opcode switch. In upcoming work, we'll move sanitize_ptr_alu()
as well out of its opcode switch so this helps to streamline both.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Move the bounds check in adjust_ptr_min_max_vals() into a small helper named
sanitize_check_bounds() in order to simplify the former a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Consolidate all error handling and provide more user-friendly error messages
from sanitize_ptr_alu() and sanitize_val_alu().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Small refactor with no semantic changes in order to consolidate the max
ptr_limit boundary check.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The mixed signed bounds check really belongs into retrieve_ptr_limit()
instead of outside of it in adjust_ptr_min_max_vals(). The reason is
that this check is not tied to PTR_TO_MAP_VALUE only, but to all pointer
types that we handle in retrieve_ptr_limit() and given errors from the latter
propagate back to adjust_ptr_min_max_vals() and lead to rejection of the
program, it's a better place to reside to avoid anything slipping through
for future types. The reason why we must reject such off_reg is that we
otherwise would not be able to derive a mask, see details in 9d7eceede7
("bpf: restrict unknown scalars of mixed signed bounds for unprivileged").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Small refactor to drag off_reg into sanitize_ptr_alu(), so we later on can
use off_reg for generalizing some of the checks for all pointer types.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
We forbid adding unknown scalars with mixed signed bounds due to the
spectre v1 masking mitigation. Hence this also needs bypass_spec_v1
flag instead of allow_ptr_leaks.
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
There is currently no way to discover the target of a tracing program
attachment after the fact. Add this information to bpf_link_info and return
it when querying the bpf_link fd.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210413091607.58945-1-toke@redhat.com
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bpf_preload_lock is already defined with DEFINE_MUTEX(). There is no
need to initialize it again. Remove the extraneous initialization.
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210405194904.GA148013@LEGION
'stack' parameter is not used in ___bpf_prog_run() after f696b8f471
("bpf: split bpf core interpreter"), the base address have been set to
FP reg. So consequently remove it.
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210331075135.3850782-1-hefengqing@huawei.com
As for bpf_link, refuse creating a non-O_RDWR fd. Since program fds
currently don't allow modifications this is a precaution, not a
straight up bug fix.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210326160501.46234-2-lmb@cloudflare.com
Invoking BPF_OBJ_GET on a pinned bpf_link checks the path access
permissions based on file_flags, but the returned fd ignores flags.
This means that any user can acquire a "read-write" fd for a pinned
link with mode 0664 by invoking BPF_OBJ_GET with BPF_F_RDONLY in
file_flags. The fd can be used to invoke BPF_LINK_DETACH, etc.
Fix this by refusing non-O_RDWR flags in BPF_OBJ_GET. This works
because OBJ_GET by default returns a read write mapping and libbpf
doesn't expose a way to override this behaviour for programs
and links.
Fixes: 70ed506c3b ("bpf: Introduce pinnable bpf_link abstraction")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210326160501.46234-1-lmb@cloudflare.com
On x86 the struct pt_regs * grabbed by task_pt_regs() points to an
offset of task->stack. The pt_regs are later dereferenced in
__bpf_get_stack (e.g. by user_mode() check). This can cause a fault if
the task in question exits while bpf_get_task_stack is executing, as
warned by task_stack_page's comment:
* When accessing the stack of a non-current task that might exit, use
* try_get_task_stack() instead. task_stack_page will return a pointer
* that could get freed out from under you.
Taking the comment's advice and using try_get_task_stack() and
put_task_stack() to hold task->stack refcount, or bail early if it's
already 0. Incrementing stack_refcount will ensure the task's stack
sticks around while we're using its data.
I noticed this bug while testing a bpf task iter similar to
bpf_iter_task_stack in selftests, except mine grabbed user stack, and
getting intermittent crashes, which resulted in dumps like:
BUG: unable to handle page fault for address: 0000000000003fe0
\#PF: supervisor read access in kernel mode
\#PF: error_code(0x0000) - not-present page
RIP: 0010:__bpf_get_stack+0xd0/0x230
<snip...>
Call Trace:
bpf_prog_0a2be35c092cb190_get_task_stacks+0x5d/0x3ec
bpf_iter_run_prog+0x24/0x81
__task_seq_show+0x58/0x80
bpf_seq_read+0xf7/0x3d0
vfs_read+0x91/0x140
ksys_read+0x59/0xd0
do_syscall_64+0x48/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: fa28dcb82a ("bpf: Introduce helper bpf_get_task_stack()")
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210401000747.3648767-1-davemarchevsky@fb.com
Reusing BPF_SK_SKB_STREAM_VERDICT is possible but its name is
confusing and more importantly we still want to distinguish them
from user-space. So we can just reuse the stream verdict code but
introduce a new type of eBPF program, skb_verdict. Users are not
allowed to attach stream_verdict and skb_verdict programs to the
same map.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210331023237.41094-10-xiyou.wangcong@gmail.com
The variable id is being assigned a value that is never read, the
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210326194348.623782-1-colin.king@canonical.com
This patch adds support to BPF verifier to allow bpf program calling
kernel function directly.
The use case included in this set is to allow bpf-tcp-cc to directly
call some tcp-cc helper functions (e.g. "tcp_cong_avoid_ai()"). Those
functions have already been used by some kernel tcp-cc implementations.
This set will also allow the bpf-tcp-cc program to directly call the
kernel tcp-cc implementation, For example, a bpf_dctcp may only want to
implement its own dctcp_cwnd_event() and reuse other dctcp_*() directly
from the kernel tcp_dctcp.c instead of reimplementing (or
copy-and-pasting) them.
The tcp-cc kernel functions mentioned above will be white listed
for the struct_ops bpf-tcp-cc programs to use in a later patch.
The white listed functions are not bounded to a fixed ABI contract.
Those functions have already been used by the existing kernel tcp-cc.
If any of them has changed, both in-tree and out-of-tree kernel tcp-cc
implementations have to be changed. The same goes for the struct_ops
bpf-tcp-cc programs which have to be adjusted accordingly.
This patch is to make the required changes in the bpf verifier.
First change is in btf.c, it adds a case in "btf_check_func_arg_match()".
When the passed in "btf->kernel_btf == true", it means matching the
verifier regs' states with a kernel function. This will handle the
PTR_TO_BTF_ID reg. It also maps PTR_TO_SOCK_COMMON, PTR_TO_SOCKET,
and PTR_TO_TCP_SOCK to its kernel's btf_id.
In the later libbpf patch, the insn calling a kernel function will
look like:
insn->code == (BPF_JMP | BPF_CALL)
insn->src_reg == BPF_PSEUDO_KFUNC_CALL /* <- new in this patch */
insn->imm == func_btf_id /* btf_id of the running kernel */
[ For the future calling function-in-kernel-module support, an array
of module btf_fds can be passed at the load time and insn->off
can be used to index into this array. ]
At the early stage of verifier, the verifier will collect all kernel
function calls into "struct bpf_kfunc_desc". Those
descriptors are stored in "prog->aux->kfunc_tab" and will
be available to the JIT. Since this "add" operation is similar
to the current "add_subprog()" and looking for the same insn->code,
they are done together in the new "add_subprog_and_kfunc()".
In the "do_check()" stage, the new "check_kfunc_call()" is added
to verify the kernel function call instruction:
1. Ensure the kernel function can be used by a particular BPF_PROG_TYPE.
A new bpf_verifier_ops "check_kfunc_call" is added to do that.
The bpf-tcp-cc struct_ops program will implement this function in
a later patch.
2. Call "btf_check_kfunc_args_match()" to ensure the regs can be
used as the args of a kernel function.
3. Mark the regs' type, subreg_def, and zext_dst.
At the later do_misc_fixups() stage, the new fixup_kfunc_call()
will replace the insn->imm with the function address (relative
to __bpf_call_base). If needed, the jit can find the btf_func_model
by calling the new bpf_jit_find_kfunc_model(prog, insn).
With the imm set to the function address, "bpftool prog dump xlated"
will be able to display the kernel function calls the same way as
it displays other bpf helper calls.
gpl_compatible program is required to call kernel function.
This feature currently requires JIT.
The verifier selftests are adjusted because of the changes in
the verbose log in add_subprog_and_kfunc().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210325015142.1544736-1-kafai@fb.com
This patch moved the subprog specific logic from
btf_check_func_arg_match() to the new btf_check_subprog_arg_match().
The core logic is left in btf_check_func_arg_match() which
will be reused later to check the kernel function call.
The "if (!btf_type_is_ptr(t))" is checked first to improve the
indentation which will be useful for a later patch.
Some of the "btf_kind_str[]" usages is replaced with the shortcut
"btf_type_str(t)".
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210325015136.1544504-1-kafai@fb.com
This patch simplifies the linfo freeing logic by combining
"bpf_prog_free_jited_linfo()" and "bpf_prog_free_unused_jited_linfo()"
into the new "bpf_prog_jit_attempt_done()".
It is a prep work for the kernel function call support. In a later
patch, freeing the kernel function call descriptors will also
be done in the "bpf_prog_jit_attempt_done()".
"bpf_prog_free_linfo()" is removed since it is only called by
"__bpf_prog_put_noref()". The kvfree() are directly called
instead.
It also takes this chance to s/kcalloc/kvcalloc/ for the jited_linfo
allocation.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210325015130.1544323-1-kafai@fb.com
Currently module can be unloaded even if there's a trampoline
register in it. It's easily reproduced by running in parallel:
# while :; do ./test_progs -t module_attach; done
# while :; do rmmod bpf_testmod; sleep 0.5; done
Taking the module reference in case the trampoline's ip is
within the module code. Releasing it when the trampoline's
ip is unregistered.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210326105900.151466-1-jolsa@kernel.org
The name string for BPF_XOR is "xor", not "or". Fix it.
Fixes: 981f94c3e9 ("bpf: Add bitwise atomic instructions")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Brendan Jackman <jackmanb@google.com>
Link: https://lore.kernel.org/bpf/20210325134141.8533-1-xukuohai@huawei.com
With the introduction of the struct_ops program type, it became possible to
implement kernel functionality in BPF, making it viable to use BPF in place
of a regular kernel module for these particular operations.
Thus far, the only user of this mechanism is for implementing TCP
congestion control algorithms. These are clearly marked as GPL-only when
implemented as modules (as seen by the use of EXPORT_SYMBOL_GPL for
tcp_register_congestion_control()), so it seems like an oversight that this
was not carried over to BPF implementations. Since this is the only user
of the struct_ops mechanism, just enforcing GPL-only for the struct_ops
program type seems like the simplest way to fix this.
Fixes: 0baf26b0fc ("bpf: tcp: Support tcp_congestion_ops in bpf")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210326100314.121853-1-toke@redhat.com
Jiri Olsa reported a bug ([1]) in kernel where cgroup local
storage pointer may be NULL in bpf_get_local_storage() helper.
There are two issues uncovered by this bug:
(1). kprobe or tracepoint prog incorrectly sets cgroup local storage
before prog run,
(2). due to change from preempt_disable to migrate_disable,
preemption is possible and percpu storage might be overwritten
by other tasks.
This issue (1) is fixed in [2]. This patch tried to address issue (2).
The following shows how things can go wrong:
task 1: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 2: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 1: run bpf program
task 1 will effectively use the percpu local storage setting by task 2
which will be either NULL or incorrect ones.
Instead of just one common local storage per cpu, this patch fixed
the issue by permitting 8 local storages per cpu and each local
storage is identified by a task_struct pointer. This way, we
allow at most 8 nested preemption between bpf_cgroup_storage_set()
and bpf_cgroup_storage_unset(). The percpu local storage slot
is released (calling bpf_cgroup_storage_unset()) by the same task
after bpf program finished running.
bpf_test_run() is also fixed to use the new bpf_cgroup_storage_set()
interface.
The patch is tested on top of [2] with reproducer in [1].
Without this patch, kernel will emit error in 2-3 minutes.
With this patch, after one hour, still no error.
[1] https://lore.kernel.org/bpf/CAKH8qBuXCfUz=w8L+Fj74OaUpbosO29niYwTki7e3Ag044_aww@mail.gmail.com/T
[2] https://lore.kernel.org/bpf/20210309185028.3763817-1-yhs@fb.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Link: https://lore.kernel.org/bpf/20210323055146.3334476-1-yhs@fb.com
Remove PTR_TO_MAP_KEY for the time being from being sanitized on pointer ALU
through sanitize_ptr_alu() mainly for 3 reasons:
1) It's currently unused and not available from unprivileged. However that by
itself is not yet a strong reason to drop the code.
2) Commit 69c087ba62 ("bpf: Add bpf_for_each_map_elem() helper") implemented
the sanitation not fully correct in that unlike stack or map_value pointer
it doesn't probe whether the access to the map key /after/ the simulated ALU
operation is still in bounds. This means that the generated mask can truncate
the offset in the non-speculative domain whereas it should only truncate in
the speculative domain. The verifier should instead reject such program as
we do for other types.
3) Given the recent fixes from f232326f69 ("bpf: Prohibit alu ops for pointer
types not defining ptr_limit"), 10d2bb2e6b ("bpf: Fix off-by-one for area
size in creating mask to left"), b5871dca25 ("bpf: Simplify alu_limit masking
for pointer arithmetic") as well as 1b1597e64e ("bpf: Add sanity check for
upper ptr_limit") the code changed quite a bit and the merge in efd13b71a3
broke the PTR_TO_MAP_KEY case due to an incorrect merge conflict.
Remove the relevant pieces for the time being and we can rework the PTR_TO_MAP_KEY
case once everything settles.
Fixes: efd13b71a3 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Fixes: 69c087ba62 ("bpf: Add bpf_for_each_map_elem() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc -Wextra wants type modifiers in the normal order:
kernel/bpf/bpf_lsm.c:70:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
70 | const static struct bpf_func_proto bpf_bprm_opts_set_proto = {
| ^~~~~
kernel/bpf/bpf_lsm.c:91:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
91 | const static struct bpf_func_proto bpf_ima_inode_hash_proto = {
| ^~~~~
Fixes: 3f6719c7b6 ("bpf: Add bpf_bprm_opts_set helper")
Fixes: 27672f0d28 ("bpf: Add a BPF helper for getting the IMA hash of an inode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210322215201.1097281-1-arnd@kernel.org
Of the three LSMs that implement the security_task_getsecid() LSM
hook, all three LSMs provide the task's objective security
credentials. This turns out to be unfortunate as most of the hook's
callers seem to expect the task's subjective credentials, although
a small handful of callers do correctly expect the objective
credentials.
This patch is the first step towards fixing the problem: it splits
the existing security_task_getsecid() hook into two variants, one
for the subjective creds, one for the objective creds.
void security_task_getsecid_subj(struct task_struct *p,
u32 *secid);
void security_task_getsecid_obj(struct task_struct *p,
u32 *secid);
While this patch does fix all of the callers to use the correct
variant, in order to keep this patch focused on the callers and to
ease review, the LSMs continue to use the same implementation for
both hooks. The net effect is that this patch should not change
the behavior of the kernel in any way, it will be up to the latter
LSM specific patches in this series to change the hook
implementations and return the correct credentials.
Acked-by: Mimi Zohar <zohar@linux.ibm.com> (IMA)
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Two insn_buf[16] variables are declared in the function which acts on
function scope and block scope respectively. The statement in the inner
block is redundant, so remove it.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210318024851.49693-1-Jianlin.Lv@arm.com
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
The fexit/fmod_ret programs can be attached to kernel functions that can sleep.
The synchronize_rcu_tasks() will not wait for such tasks to complete.
In such case the trampoline image will be freed and when the task
wakes up the return IP will point to freed memory causing the crash.
Solve this by adding percpu_ref_get/put for the duration of trampoline
and separate trampoline vs its image life times.
The "half page" optimization has to be removed, since
first_half->second_half->first_half transition cannot be guaranteed to
complete in deterministic time. Every trampoline update becomes a new image.
The image with fmod_ret or fexit progs will be freed via percpu_ref_kill and
call_rcu_tasks. Together they will wait for the original function and
trampoline asm to complete. The trampoline is patched from nop to jmp to skip
fexit progs. They are freed independently from the trampoline. The image with
fentry progs only will be freed via call_rcu_tasks_trace+call_rcu_tasks which
will wait for both sleepable and non-sleepable progs to complete.
Fixes: fec56f5890 ("bpf: Introduce BPF trampoline")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paul E. McKenney <paulmck@kernel.org> # for RCU
Link: https://lore.kernel.org/bpf/20210316210007.38949-1-alexei.starovoitov@gmail.com
Given we know the max possible value of ptr_limit at the time of retrieving
the latter, add basic assertions, so that the verifier can bail out if
anything looks odd and reject the program. Nothing triggered this so far,
but it also does not hurt to have these.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Instead of having the mov32 with aux->alu_limit - 1 immediate, move this
operation to retrieve_ptr_limit() instead to simplify the logic and to
allow for subsequent sanity boundary checks inside retrieve_ptr_limit().
This avoids in future that at the time of the verifier masking rewrite
we'd run into an underflow which would not sign extend due to the nature
of mov32 instruction.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
retrieve_ptr_limit() computes the ptr_limit for registers with stack and
map_value type. ptr_limit is the size of the memory area that is still
valid / in-bounds from the point of the current position and direction
of the operation (add / sub). This size will later be used for masking
the operation such that attempting out-of-bounds access in the speculative
domain is redirected to remain within the bounds of the current map value.
When masking to the right the size is correct, however, when masking to
the left, the size is off-by-one which would lead to an incorrect mask
and thus incorrect arithmetic operation in the non-speculative domain.
Piotr found that if the resulting alu_limit value is zero, then the
BPF_MOV32_IMM() from the fixup_bpf_calls() rewrite will end up loading
0xffffffff into AX instead of sign-extending to the full 64 bit range,
and as a result, this allows abuse for executing speculatively out-of-
bounds loads against 4GB window of address space and thus extracting the
contents of kernel memory via side-channel.
Fixes: 979d63d50c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The purpose of this patch is to streamline error propagation and in particular
to propagate retrieve_ptr_limit() errors for pointer types that are not defining
a ptr_limit such that register-based alu ops against these types can be rejected.
The main rationale is that a gap has been identified by Piotr in the existing
protection against speculatively out-of-bounds loads, for example, in case of
ctx pointers, unprivileged programs can still perform pointer arithmetic. This
can be abused to execute speculatively out-of-bounds loads without restrictions
and thus extract contents of kernel memory.
Fix this by rejecting unprivileged programs that attempt any pointer arithmetic
on unprotected pointer types. The two affected ones are pointer to ctx as well
as pointer to map. Field access to a modified ctx' pointer is rejected at a
later point in time in the verifier, and 7c69673262 ("bpf: Permit map_ptr
arithmetic with opcode add and offset 0") only relevant for root-only use cases.
Risk of unprivileged program breakage is considered very low.
Fixes: 7c69673262 ("bpf: Permit map_ptr arithmetic with opcode add and offset 0")
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The sparse tool complains as follows:
kernel/bpf/bpf_task_storage.c:23:1: warning:
symbol '__pcpu_scope_bpf_task_storage_busy' was not declared. Should it be static?
This symbol is not used outside of bpf_task_storage.c, so this
commit marks it static.
Fixes: bc235cdb42 ("bpf: Prevent deadlock from recursive bpf_task_storage_[get|delete]")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210311131505.1901509-1-weiyongjun1@huawei.com
A typo is found out by codespell tool in 34th lines of hashtab.c:
$ codespell ./kernel/bpf/
./hashtab.c:34 : differrent ==> different
Fix a typo found by codespell.
Signed-off-by: Liu xuzhi <liu.xuzhi@zte.com.cn>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210311123103.323589-1-liu.xuzhi@zte.com.cn
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-09
The following pull-request contains BPF updates for your *net-next* tree.
We've added 90 non-merge commits during the last 17 day(s) which contain
a total of 114 files changed, 5158 insertions(+), 1288 deletions(-).
The main changes are:
1) Faster bpf_redirect_map(), from Björn.
2) skmsg cleanup, from Cong.
3) Support for floating point types in BTF, from Ilya.
4) Documentation for sys_bpf commands, from Joe.
5) Support for sk_lookup in bpf_prog_test_run, form Lorenz.
6) Enable task local storage for tracing programs, from Song.
7) bpf_for_each_map_elem() helper, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The XDP_REDIRECT implementations for maps and non-maps are fairly
similar, but obviously need to take different code paths depending on
if the target is using a map or not. Today, the redirect targets for
XDP either uses a map, or is based on ifindex.
Here, the map type and id are added to bpf_redirect_info, instead of
the actual map. Map type, map item/ifindex, and the map_id (if any) is
passed to xdp_do_redirect().
For ifindex-based redirect, used by the bpf_redirect() XDP BFP helper,
a special map type/id are used. Map type of UNSPEC together with map id
equal to INT_MAX has the special meaning of an ifindex based
redirect. Note that valid map ids are 1 inclusive, INT_MAX exclusive
([1,INT_MAX[).
In addition to making the code easier to follow, using explicit type
and id in bpf_redirect_info has a slight positive performance impact
by avoiding a pointer indirection for the map type lookup, and instead
use the cacheline for bpf_redirect_info.
Since the actual map is not passed via bpf_redirect_info anymore, the
map lookup is only done in the BPF helper. This means that the
bpf_clear_redirect_map() function can be removed. The actual map item
is RCU protected.
The bpf_redirect_info flags member is not used by XDP, and not
read/written any more. The map member is only written to when
required/used, and not unconditionally.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210308112907.559576-3-bjorn.topel@gmail.com
Currently the bpf_redirect_map() implementation dispatches to the
correct map-lookup function via a switch-statement. To avoid the
dispatching, this change adds bpf_redirect_map() as a map
operation. Each map provides its bpf_redirect_map() version, and
correct function is automatically selected by the BPF verifier.
A nice side-effect of the code movement is that the map lookup
functions are now local to the map implementation files, which removes
one additional function call.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210308112907.559576-2-bjorn.topel@gmail.com
bpf_fd_inode_storage_lookup_elem() returned NULL when getting a bad FD,
which caused -ENOENT in bpf_map_copy_value. -EBADF error is better than
-ENOENT for a bad FD behaviour.
The patch was partially contributed by CyberArk Software, Inc.
Fixes: 8ea636848a ("bpf: Implement bpf_local_storage for inodes")
Signed-off-by: Tal Lossos <tallossos@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210307120948.61414-1-tallossos@gmail.com
The syzbot got FD of vmlinux BTF and passed it into map_create which caused
crash in btf_type_id_size() when it tried to access resolved_ids. The vmlinux
BTF doesn't have 'resolved_ids' and 'resolved_sizes' initialized to save
memory. To avoid such issues disallow using vmlinux BTF in prog_load and
map_create commands.
Fixes: 5329722057 ("bpf: Assign ID to vmlinux BTF and return extra info for BTF in GET_OBJ_INFO")
Reported-by: syzbot+8bab8ed346746e7540e8@syzkaller.appspotmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210307225248.79031-1-alexei.starovoitov@gmail.com
As pointed out by Ilya and explained in the new comment, there's a
discrepancy between x86 and BPF CMPXCHG semantics: BPF always loads
the value from memory into r0, while x86 only does so when r0 and the
value in memory are different. The same issue affects s390.
At first this might sound like pure semantics, but it makes a real
difference when the comparison is 32-bit, since the load will
zero-extend r0/rax.
The fix is to explicitly zero-extend rax after doing such a
CMPXCHG. Since this problem affects multiple archs, this is done in
the verifier by patching in a BPF_ZEXT_REG instruction after every
32-bit cmpxchg. Any archs that don't need such manual zero-extension
can do a look-ahead with insn_is_zext to skip the unnecessary mov.
Note this still goes on top of Ilya's patch:
https://lore.kernel.org/bpf/20210301154019.129110-1-iii@linux.ibm.com/T/#u
Differences v5->v6[1]:
- Moved is_cmpxchg_insn and ensured it can be safely re-used. Also renamed it
and removed 'inline' to match the style of the is_*_function helpers.
- Fixed up comments in verifier test (thanks for the careful review, Martin!)
Differences v4->v5[1]:
- Moved the logic entirely into opt_subreg_zext_lo32_rnd_hi32, thanks to Martin
for suggesting this.
Differences v3->v4[1]:
- Moved the optimization against pointless zext into the correct place:
opt_subreg_zext_lo32_rnd_hi32 is called _after_ fixup_bpf_calls.
Differences v2->v3[1]:
- Moved patching into fixup_bpf_calls (patch incoming to rename this function)
- Added extra commentary on bpf_jit_needs_zext
- Added check to avoid adding a pointless zext(r0) if there's already one there.
Difference v1->v2[1]: Now solved centrally in the verifier instead of
specifically for the x86 JIT. Thanks to Ilya and Daniel for the suggestions!
[1] v5: https://lore.kernel.org/bpf/CA+i-1C3ytZz6FjcPmUg5s4L51pMQDxWcZNvM86w4RHZ_o2khwg@mail.gmail.com/T/#t
v4: https://lore.kernel.org/bpf/CA+i-1C3ytZz6FjcPmUg5s4L51pMQDxWcZNvM86w4RHZ_o2khwg@mail.gmail.com/T/#t
v3: https://lore.kernel.org/bpf/08669818-c99d-0d30-e1db-53160c063611@iogearbox.net/T/#t
v2: https://lore.kernel.org/bpf/08669818-c99d-0d30-e1db-53160c063611@iogearbox.net/T/#t
v1: https://lore.kernel.org/bpf/d7ebaefb-bfd6-a441-3ff2-2fdfe699b1d2@iogearbox.net/T/#t
Reported-by: Ilya Leoshkevich <iii@linux.ibm.com>
Fixes: 5ffa25502b ("bpf: Add instructions for atomic_[cmp]xchg")
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
On the kernel side, introduce a new btf_kind_operations. It is
similar to that of BTF_KIND_INT, however, it does not need to
handle encodings and bit offsets. Do not implement printing, since
the kernel does not know how to format floating-point values.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210226202256.116518-7-iii@linux.ibm.com
insn_has_def32() returns false for 32-bit BPF_FETCH insns. This makes
adjust_insn_aux_data() incorrectly set zext_dst, as can be seen in [1].
This happens because insn_no_def() does not know about the BPF_FETCH
variants of BPF_STX.
Fix in two steps.
First, replace insn_no_def() with insn_def_regno(), which returns the
register an insn defines. Normally insn_no_def() calls are followed by
insn->dst_reg uses; replace those with the insn_def_regno() return
value.
Second, adjust the BPF_STX special case in is_reg64() to deal with
queries made from opt_subreg_zext_lo32_rnd_hi32(), where the state
information is no longer available. Add a comment, since the purpose
of this special case is not clear at first glance.
[1] https://lore.kernel.org/bpf/20210223150845.1857620-1-jackmanb@google.com/
Fixes: 5ffa25502b ("bpf: Add instructions for atomic_[cmp]xchg")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Brendan Jackman <jackmanb@google.com>
Link: https://lore.kernel.org/bpf/20210301154019.129110-1-iii@linux.ibm.com
This patch added support for arraymap and percpu arraymap.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204928.3885192-1-yhs@fb.com
The bpf_for_each_map_elem() helper is introduced which
iterates all map elements with a callback function. The
helper signature looks like
long bpf_for_each_map_elem(map, callback_fn, callback_ctx, flags)
and for each map element, the callback_fn will be called. For example,
like hashmap, the callback signature may look like
long callback_fn(map, key, val, callback_ctx)
There are two known use cases for this. One is from upstream ([1]) where
a for_each_map_elem helper may help implement a timeout mechanism
in a more generic way. Another is from our internal discussion
for a firewall use case where a map contains all the rules. The packet
data can be compared to all these rules to decide allow or deny
the packet.
For array maps, users can already use a bounded loop to traverse
elements. Using this helper can avoid using bounded loop. For other
type of maps (e.g., hash maps) where bounded loop is hard or
impossible to use, this helper provides a convenient way to
operate on all elements.
For callback_fn, besides map and map element, a callback_ctx,
allocated on caller stack, is also passed to the callback
function. This callback_ctx argument can provide additional
input and allow to write to caller stack for output.
If the callback_fn returns 0, the helper will iterate through next
element if available. If the callback_fn returns 1, the helper
will stop iterating and returns to the bpf program. Other return
values are not used for now.
Currently, this helper is only available with jit. It is possible
to make it work with interpreter with so effort but I leave it
as the future work.
[1]: https://lore.kernel.org/bpf/20210122205415.113822-1-xiyou.wangcong@gmail.com/
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204925.3884923-1-yhs@fb.com
Currently, verifier function add_subprog() returns 0 for success
and negative value for failure. Change the return value
to be the subprog number for success. This functionality will be
used in the next patch to save a call to find_subprog().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204924.3884848-1-yhs@fb.com
Later proposed bpf_for_each_map_elem() helper has callback
function as one of its arguments. This patch refactored
check_func_call() to permit callback function which sets
callee state. Different callback functions may have
different callee states.
There is no functionality change for this patch.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204923.3884627-1-yhs@fb.com
Factor out the function verbose_invalid_scalar() to verbose
print if a scalar is not in a tnum range. There is no
functionality change and the function will be used by
later patch which introduced bpf_for_each_map_elem().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204922.3884375-1-yhs@fb.com
During verifier check_cfg(), all instructions are
visited to ensure verifier can handle program control flows.
This patch factored out function visit_func_call_insn()
so it can be reused in later patch to visit callback function
calls. There is no functionality change for this patch.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210226204920.3884136-1-yhs@fb.com
Alexei Starovoitov says:
====================
pull-request: bpf 2021-02-26
1) Fix for bpf atomic insns with src_reg=r0, from Brendan.
2) Fix use after free due to bpf_prog_clone, from Cong.
3) Drop imprecise verifier log message, from Dmitrii.
4) Remove incorrect blank line in bpf helper description, from Hangbin.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: No need to drop the packet when there is no geneve opt
bpf: Remove blank line in bpf helper description comment
tools/resolve_btfids: Fix build error with older host toolchains
selftests/bpf: Fix a compiler warning in global func test
bpf: Drop imprecise log message
bpf: Clear percpu pointers in bpf_prog_clone_free()
bpf: Fix a warning message in mark_ptr_not_null_reg()
bpf, x86: Fix BPF_FETCH atomic and/or/xor with r0 as src
====================
Link: https://lore.kernel.org/r/20210226193737.57004-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function has become overloaded, it actually does lots of diverse
things in a single pass. Rename it to avoid confusion, and add some
concise commentary.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210217104509.2423183-1-jackmanb@google.com
Instead of using integer literal here and there use macro name for
better context.
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210225202629.585485-1-me@ubique.spb.ru
BPF helpers bpf_task_storage_[get|delete] could hold two locks:
bpf_local_storage_map_bucket->lock and bpf_local_storage->lock. Calling
these helpers from fentry/fexit programs on functions in bpf_*_storage.c
may cause deadlock on either locks.
Prevent such deadlock with a per cpu counter, bpf_task_storage_busy. We
need this counter to be global, because the two locks here belong to two
different objects: bpf_local_storage_map and bpf_local_storage. If we
pick one of them as the owner of the counter, it is still possible to
trigger deadlock on the other lock. For example, if bpf_local_storage_map
owns the counters, it cannot prevent deadlock on bpf_local_storage->lock
when two maps are used.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210225234319.336131-3-songliubraving@fb.com
To access per-task data, BPF programs usually creates a hash table with
pid as the key. This is not ideal because:
1. The user need to estimate the proper size of the hash table, which may
be inaccurate;
2. Big hash tables are slow;
3. To clean up the data properly during task terminations, the user need
to write extra logic.
Task local storage overcomes these issues and offers a better option for
these per-task data. Task local storage is only available to BPF_LSM. Now
enable it for tracing programs.
Unlike LSM programs, tracing programs can be called in IRQ contexts.
Helpers that access task local storage are updated to use
raw_spin_lock_irqsave() instead of raw_spin_lock_bh().
Tracing programs can attach to functions on the task free path, e.g.
exit_creds(). To avoid allocating task local storage after
bpf_task_storage_free(). bpf_task_storage_get() is updated to not allocate
new storage when the task is not refcounted (task->usage == 0).
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210225234319.336131-2-songliubraving@fb.com
Now it is possible for global function to have a pointer argument that
points to something different than struct. Drop the irrelevant log
message and keep the logic same.
Fixes: e5069b9c23 ("bpf: Support pointers in global func args")
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210223090416.333943-1-me@ubique.spb.ru
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYCegywAKCRCRxhvAZXjc
ouJ6AQDlf+7jCQlQdeKKoN9QDFfMzG1ooemat36EpRRTONaGuAD8D9A4sUsG4+5f
4IU5Lj9oY4DEmF8HenbWK2ZHsesL2Qg=
=yPaw
-----END PGP SIGNATURE-----
Merge tag 'idmapped-mounts-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull idmapped mounts from Christian Brauner:
"This introduces idmapped mounts which has been in the making for some
time. Simply put, different mounts can expose the same file or
directory with different ownership. This initial implementation comes
with ports for fat, ext4 and with Christoph's port for xfs with more
filesystems being actively worked on by independent people and
maintainers.
Idmapping mounts handle a wide range of long standing use-cases. Here
are just a few:
- Idmapped mounts make it possible to easily share files between
multiple users or multiple machines especially in complex
scenarios. For example, idmapped mounts will be used in the
implementation of portable home directories in
systemd-homed.service(8) where they allow users to move their home
directory to an external storage device and use it on multiple
computers where they are assigned different uids and gids. This
effectively makes it possible to assign random uids and gids at
login time.
- It is possible to share files from the host with unprivileged
containers without having to change ownership permanently through
chown(2).
- It is possible to idmap a container's rootfs and without having to
mangle every file. For example, Chromebooks use it to share the
user's Download folder with their unprivileged containers in their
Linux subsystem.
- It is possible to share files between containers with
non-overlapping idmappings.
- Filesystem that lack a proper concept of ownership such as fat can
use idmapped mounts to implement discretionary access (DAC)
permission checking.
- They allow users to efficiently changing ownership on a per-mount
basis without having to (recursively) chown(2) all files. In
contrast to chown (2) changing ownership of large sets of files is
instantenous with idmapped mounts. This is especially useful when
ownership of a whole root filesystem of a virtual machine or
container is changed. With idmapped mounts a single syscall
mount_setattr syscall will be sufficient to change the ownership of
all files.
- Idmapped mounts always take the current ownership into account as
idmappings specify what a given uid or gid is supposed to be mapped
to. This contrasts with the chown(2) syscall which cannot by itself
take the current ownership of the files it changes into account. It
simply changes the ownership to the specified uid and gid. This is
especially problematic when recursively chown(2)ing a large set of
files which is commong with the aforementioned portable home
directory and container and vm scenario.
- Idmapped mounts allow to change ownership locally, restricting it
to specific mounts, and temporarily as the ownership changes only
apply as long as the mount exists.
Several userspace projects have either already put up patches and
pull-requests for this feature or will do so should you decide to pull
this:
- systemd: In a wide variety of scenarios but especially right away
in their implementation of portable home directories.
https://systemd.io/HOME_DIRECTORY/
- container runtimes: containerd, runC, LXD:To share data between
host and unprivileged containers, unprivileged and privileged
containers, etc. The pull request for idmapped mounts support in
containerd, the default Kubernetes runtime is already up for quite
a while now: https://github.com/containerd/containerd/pull/4734
- The virtio-fs developers and several users have expressed interest
in using this feature with virtual machines once virtio-fs is
ported.
- ChromeOS: Sharing host-directories with unprivileged containers.
I've tightly synced with all those projects and all of those listed
here have also expressed their need/desire for this feature on the
mailing list. For more info on how people use this there's a bunch of
talks about this too. Here's just two recent ones:
https://www.cncf.io/wp-content/uploads/2020/12/Rootless-Containers-in-Gitpod.pdfhttps://fosdem.org/2021/schedule/event/containers_idmap/
This comes with an extensive xfstests suite covering both ext4 and
xfs:
https://git.kernel.org/brauner/xfstests-dev/h/idmapped_mounts
It covers truncation, creation, opening, xattrs, vfscaps, setid
execution, setgid inheritance and more both with idmapped and
non-idmapped mounts. It already helped to discover an unrelated xfs
setgid inheritance bug which has since been fixed in mainline. It will
be sent for inclusion with the xfstests project should you decide to
merge this.
In order to support per-mount idmappings vfsmounts are marked with
user namespaces. The idmapping of the user namespace will be used to
map the ids of vfs objects when they are accessed through that mount.
By default all vfsmounts are marked with the initial user namespace.
The initial user namespace is used to indicate that a mount is not
idmapped. All operations behave as before and this is verified in the
testsuite.
Based on prior discussions we want to attach the whole user namespace
and not just a dedicated idmapping struct. This allows us to reuse all
the helpers that already exist for dealing with idmappings instead of
introducing a whole new range of helpers. In addition, if we decide in
the future that we are confident enough to enable unprivileged users
to setup idmapped mounts the permission checking can take into account
whether the caller is privileged in the user namespace the mount is
currently marked with.
The user namespace the mount will be marked with can be specified by
passing a file descriptor refering to the user namespace as an
argument to the new mount_setattr() syscall together with the new
MOUNT_ATTR_IDMAP flag. The system call follows the openat2() pattern
of extensibility.
The following conditions must be met in order to create an idmapped
mount:
- The caller must currently have the CAP_SYS_ADMIN capability in the
user namespace the underlying filesystem has been mounted in.
- The underlying filesystem must support idmapped mounts.
- The mount must not already be idmapped. This also implies that the
idmapping of a mount cannot be altered once it has been idmapped.
- The mount must be a detached/anonymous mount, i.e. it must have
been created by calling open_tree() with the OPEN_TREE_CLONE flag
and it must not already have been visible in the filesystem.
The last two points guarantee easier semantics for userspace and the
kernel and make the implementation significantly simpler.
By default vfsmounts are marked with the initial user namespace and no
behavioral or performance changes are observed.
The manpage with a detailed description can be found here:
1d7b902e28
In order to support idmapped mounts, filesystems need to be changed
and mark themselves with the FS_ALLOW_IDMAP flag in fs_flags. The
patches to convert individual filesystem are not very large or
complicated overall as can be seen from the included fat, ext4, and
xfs ports. Patches for other filesystems are actively worked on and
will be sent out separately. The xfstestsuite can be used to verify
that port has been done correctly.
The mount_setattr() syscall is motivated independent of the idmapped
mounts patches and it's been around since July 2019. One of the most
valuable features of the new mount api is the ability to perform
mounts based on file descriptors only.
Together with the lookup restrictions available in the openat2()
RESOLVE_* flag namespace which we added in v5.6 this is the first time
we are close to hardened and race-free (e.g. symlinks) mounting and
path resolution.
While userspace has started porting to the new mount api to mount
proper filesystems and create new bind-mounts it is currently not
possible to change mount options of an already existing bind mount in
the new mount api since the mount_setattr() syscall is missing.
With the addition of the mount_setattr() syscall we remove this last
restriction and userspace can now fully port to the new mount api,
covering every use-case the old mount api could. We also add the
crucial ability to recursively change mount options for a whole mount
tree, both removing and adding mount options at the same time. This
syscall has been requested multiple times by various people and
projects.
There is a simple tool available at
https://github.com/brauner/mount-idmapped
that allows to create idmapped mounts so people can play with this
patch series. I'll add support for the regular mount binary should you
decide to pull this in the following weeks:
Here's an example to a simple idmapped mount of another user's home
directory:
u1001@f2-vm:/$ sudo ./mount --idmap both:1000:1001:1 /home/ubuntu/ /mnt
u1001@f2-vm:/$ ls -al /home/ubuntu/
total 28
drwxr-xr-x 2 ubuntu ubuntu 4096 Oct 28 22:07 .
drwxr-xr-x 4 root root 4096 Oct 28 04:00 ..
-rw------- 1 ubuntu ubuntu 3154 Oct 28 22:12 .bash_history
-rw-r--r-- 1 ubuntu ubuntu 220 Feb 25 2020 .bash_logout
-rw-r--r-- 1 ubuntu ubuntu 3771 Feb 25 2020 .bashrc
-rw-r--r-- 1 ubuntu ubuntu 807 Feb 25 2020 .profile
-rw-r--r-- 1 ubuntu ubuntu 0 Oct 16 16:11 .sudo_as_admin_successful
-rw------- 1 ubuntu ubuntu 1144 Oct 28 00:43 .viminfo
u1001@f2-vm:/$ ls -al /mnt/
total 28
drwxr-xr-x 2 u1001 u1001 4096 Oct 28 22:07 .
drwxr-xr-x 29 root root 4096 Oct 28 22:01 ..
-rw------- 1 u1001 u1001 3154 Oct 28 22:12 .bash_history
-rw-r--r-- 1 u1001 u1001 220 Feb 25 2020 .bash_logout
-rw-r--r-- 1 u1001 u1001 3771 Feb 25 2020 .bashrc
-rw-r--r-- 1 u1001 u1001 807 Feb 25 2020 .profile
-rw-r--r-- 1 u1001 u1001 0 Oct 16 16:11 .sudo_as_admin_successful
-rw------- 1 u1001 u1001 1144 Oct 28 00:43 .viminfo
u1001@f2-vm:/$ touch /mnt/my-file
u1001@f2-vm:/$ setfacl -m u:1001:rwx /mnt/my-file
u1001@f2-vm:/$ sudo setcap -n 1001 cap_net_raw+ep /mnt/my-file
u1001@f2-vm:/$ ls -al /mnt/my-file
-rw-rwxr--+ 1 u1001 u1001 0 Oct 28 22:14 /mnt/my-file
u1001@f2-vm:/$ ls -al /home/ubuntu/my-file
-rw-rwxr--+ 1 ubuntu ubuntu 0 Oct 28 22:14 /home/ubuntu/my-file
u1001@f2-vm:/$ getfacl /mnt/my-file
getfacl: Removing leading '/' from absolute path names
# file: mnt/my-file
# owner: u1001
# group: u1001
user::rw-
user:u1001:rwx
group::rw-
mask::rwx
other::r--
u1001@f2-vm:/$ getfacl /home/ubuntu/my-file
getfacl: Removing leading '/' from absolute path names
# file: home/ubuntu/my-file
# owner: ubuntu
# group: ubuntu
user::rw-
user:ubuntu:rwx
group::rw-
mask::rwx
other::r--"
* tag 'idmapped-mounts-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux: (41 commits)
xfs: remove the possibly unused mp variable in xfs_file_compat_ioctl
xfs: support idmapped mounts
ext4: support idmapped mounts
fat: handle idmapped mounts
tests: add mount_setattr() selftests
fs: introduce MOUNT_ATTR_IDMAP
fs: add mount_setattr()
fs: add attr_flags_to_mnt_flags helper
fs: split out functions to hold writers
namespace: only take read lock in do_reconfigure_mnt()
mount: make {lock,unlock}_mount_hash() static
namespace: take lock_mount_hash() directly when changing flags
nfs: do not export idmapped mounts
overlayfs: do not mount on top of idmapped mounts
ecryptfs: do not mount on top of idmapped mounts
ima: handle idmapped mounts
apparmor: handle idmapped mounts
fs: make helpers idmap mount aware
exec: handle idmapped mounts
would_dump: handle idmapped mounts
...
The WARN_ON() argument is a condition, not an error message. So this
code will print a stack trace but will not print the warning message.
Fix that and also change it to only WARN_ONCE().
Fixes: 4ddb74165a ("bpf: Extract nullable reg type conversion into a helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/YCzJlV3hnF%2Ft1Pk4@mwanda
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-02-16
The following pull-request contains BPF updates for your *net-next* tree.
There's a small merge conflict between 7eeba1706e ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f81 ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:
[...]
lock_sock(sk);
err = tcp_zerocopy_receive(sk, &zc, &tss);
err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
&zc, &len, err);
release_sock(sk);
[...]
We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).
The main changes are:
1) Adds support of pointers to types with known size among global function
args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.
2) Add bpf_iter for task_vma which can be used to generate information similar
to /proc/pid/maps, from Song Liu.
3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
rewriting bind user ports from BPF side below the ip_unprivileged_port_start
range, both from Stanislav Fomichev.
4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
as well as per-cpu maps for the latter, from Alexei Starovoitov.
5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
for sleepable programs, both from KP Singh.
6) Extend verifier to enable variable offset read/write access to the BPF
program stack, from Andrei Matei.
7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
query device MTU from programs, from Jesper Dangaard Brouer.
8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
tracing programs, from Florent Revest.
9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
otherwise too many passes are required, from Gary Lin.
10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
verification both related to zero-extension handling, from Ilya Leoshkevich.
11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.
12) Batch of AF_XDP selftest cleanups and small performance improvement
for libbpf's xsk map redirect for newer kernels, from Björn Töpel.
13) Follow-up BPF doc and verifier improvements around atomics with
BPF_FETCH, from Brendan Jackman.
14) Permit zero-sized data sections e.g. if ELF .rodata section contains
read-only data from local variables, from Yonghong Song.
15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
test_global_func4 fails on s390 as reported by Yauheni in [1].
The immediate problem is that the zext code includes the instruction,
whose result needs to be zero-extended, into the zero-extension
patchlet, and if this instruction happens to be a branch, then its
delta is not adjusted. As a result, the verifier rejects the program
later.
However, according to [2], as far as the verifier's algorithm is
concerned and as specified by the insn_no_def() function, branching
insns do not define anything. This includes call insns, even though
one might argue that they define %r0.
This means that the real problem is that zero extension kicks in at
all. This happens because clear_caller_saved_regs() sets BPF_REG_0's
subreg_def after global function calls. This can be fixed in many
ways; this patch mimics what helper function call handling already
does.
[1] https://lore.kernel.org/bpf/20200903140542.156624-1-yauheni.kaliuta@redhat.com/
[2] https://lore.kernel.org/bpf/CAADnVQ+2RPKcftZw8d+B1UwB35cpBhpF5u3OocNh90D9pETPwg@mail.gmail.com/
Fixes: 51c39bb1d5 ("bpf: Introduce function-by-function verification")
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210212040408.90109-1-iii@linux.ibm.com
Add an ability to pass a pointer to a type with known size in arguments
of a global function. Such pointers may be used to overcome the limit on
the maximum number of arguments, avoid expensive and tricky workarounds
and to have multiple output arguments.
A referenced type may contain pointers but indirect access through them
isn't supported.
The implementation consists of two parts. If a global function has an
argument that is a pointer to a type with known size then:
1) In btf_check_func_arg_match(): check that the corresponding
register points to NULL or to a valid memory region that is large enough
to contain the expected argument's type.
2) In btf_prepare_func_args(): set the corresponding register type to
PTR_TO_MEM_OR_NULL and its size to the size of the expected type.
Only global functions are supported because allowance of pointers for
static functions might break validation. Consider the following
scenario. A static function has a pointer argument. A caller passes
pointer to its stack memory. Because the callee can change referenced
memory verifier cannot longer assume any particular slot type of the
caller's stack memory hence the slot type is changed to SLOT_MISC. If
there is an operation that relies on slot type other than SLOT_MISC then
verifier won't be able to infer safety of the operation.
When verifier sees a static function that has a pointer argument
different from PTR_TO_CTX then it skips arguments check and continues
with "inline" validation with more information available. The operation
that relies on the particular slot type now succeeds.
Because global functions were not allowed to have pointer arguments
different from PTR_TO_CTX it's not possible to break existing and valid
code.
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210212205642.620788-4-me@ubique.spb.ru
Extract conversion from a register's nullable type to a type with a
value. The helper will be used in mark_ptr_not_null_reg().
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210212205642.620788-3-me@ubique.spb.ru
Using "reg" for an array of bpf_reg_state and "reg[i + 1]" for an
individual bpf_reg_state is error-prone and verbose. Use "regs" for the
former and "reg" for the latter as other code nearby does.
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210212205642.620788-2-me@ubique.spb.ru
Recently noticed that when mod32 with a known src reg of 0 is performed,
then the dst register is 32-bit truncated in verifier:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=inv0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=inv0 R1_w=inv-1 R10=fp0
2: (b4) w2 = -1
3: R0_w=inv0 R1_w=inv-1 R2_w=inv4294967295 R10=fp0
3: (9c) w1 %= w0
4: R0_w=inv0 R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
4: (b7) r0 = 1
5: R0_w=inv1 R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
5: (1d) if r1 == r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
6: R0_w=inv1 R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
6: (b7) r0 = 2
7: R0_w=inv2 R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2_w=inv4294967295 R10=fp0
7: (95) exit
7: R0=inv1 R1=inv(id=0,umin_value=4294967295,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R2=inv4294967295 R10=fp0
7: (95) exit
However, as a runtime result, we get 2 instead of 1, meaning the dst
register does not contain (u32)-1 in this case. The reason is fairly
straight forward given the 0 test leaves the dst register as-is:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+1
4: (9c) w1 %= w0
5: (b7) r0 = 1
6: (1d) if r1 == r2 goto pc+1
7: (b7) r0 = 2
8: (95) exit
This was originally not an issue given the dst register was marked as
completely unknown (aka 64 bit unknown). However, after 468f6eafa6
("bpf: fix 32-bit ALU op verification") the verifier casts the register
output to 32 bit, and hence it becomes 32 bit unknown. Note that for
the case where the src register is unknown, the dst register is marked
64 bit unknown. After the fix, the register is truncated by the runtime
and the test passes:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+2
4: (9c) w1 %= w0
5: (05) goto pc+1
6: (bc) w1 = w1
7: (b7) r0 = 1
8: (1d) if r1 == r2 goto pc+1
9: (b7) r0 = 2
10: (95) exit
Semantics also match with {R,W}x mod{64,32} 0 -> {R,W}x. Invalid div
has always been {R,W}x div{64,32} 0 -> 0. Rewrites are as follows:
mod32: mod64:
(16) if w0 == 0x0 goto pc+2 (15) if r0 == 0x0 goto pc+1
(9c) w1 %= w0 (9f) r1 %= r0
(05) goto pc+1
(bc) w1 = w1
Fixes: 468f6eafa6 ("bpf: fix 32-bit ALU op verification")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The devmap bulk queue is allocated with GFP_ATOMIC and the allocation
may fail if there is no available space in existing percpu pool.
Since commit 75ccae62cb ("xdp: Move devmap bulk queue into struct net_device")
moved the bulk queue allocation to NETDEV_REGISTER callback, whose context
is allowed to sleep, use GFP_KERNEL instead of GFP_ATOMIC to let percpu
allocator extend the pool when needed and avoid possible failure of netdev
registration.
As the required alignment is natural, we can simply use alloc_percpu().
Fixes: 75ccae62cb ("xdp: Move devmap bulk queue into struct net_device")
Signed-off-by: Jun'ichi Nomura <junichi.nomura@nec.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210209082451.GA44021@jeru.linux.bs1.fc.nec.co.jp
Commit 15d83c4d7c ("bpf: Allow loading of a bpf_iter program")
cached btf_id in struct bpf_iter_target_info so later on
if it can be checked cheaply compared to checking registered names.
syzbot found a bug that uninitialized value may occur to
bpf_iter_target_info->btf_id. This is because we allocated
bpf_iter_target_info structure with kmalloc and never initialized
field btf_id afterwards. This uninitialized btf_id is typically
compared to a u32 bpf program func proto btf_id, and the chance
of being equal is extremely slim.
This patch fixed the issue by using kzalloc which will also
prevent future likely instances due to adding new fields.
Fixes: 15d83c4d7c ("bpf: Allow loading of a bpf_iter program")
Reported-by: syzbot+580f4f2a272e452d55cb@syzkaller.appspotmail.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210212005926.2875002-1-yhs@fb.com
Introduce task_vma bpf_iter to print memory information of a process. It
can be used to print customized information similar to /proc/<pid>/maps.
Current /proc/<pid>/maps and /proc/<pid>/smaps provide information of
vma's of a process. However, these information are not flexible enough to
cover all use cases. For example, if a vma cover mixed 2MB pages and 4kB
pages (x86_64), there is no easy way to tell which address ranges are
backed by 2MB pages. task_vma solves the problem by enabling the user to
generate customize information based on the vma (and vma->vm_mm,
vma->vm_file, etc.).
To access the vma safely in the BPF program, task_vma iterator holds
target mmap_lock while calling the BPF program. If the mmap_lock is
contended, task_vma unlocks mmap_lock between iterations to unblock the
writer(s). This lock contention avoidance mechanism is similar to the one
used in show_smaps_rollup().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210212183107.50963-2-songliubraving@fb.com
All 32-bit variants of BPF_FETCH (add, and, or, xor, xchg, cmpxchg)
define a 32-bit subreg and thus have zext_dst set. Their encoding,
however, uses dst_reg field as a base register, which causes
opt_subreg_zext_lo32_rnd_hi32() to zero-extend said base register
instead of the one the insn really defines (r0 or src_reg).
Fix by properly choosing a register being defined, similar to how
check_atomic() already does that.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210210204502.83429-1-iii@linux.ibm.com
bpf_prog_realloc copies contents of struct bpf_prog.
The pointers have to be cleared before freeing old struct.
Reported-by: Ilya Leoshkevich <iii@linux.ibm.com>
Fixes: 700d4796ef ("bpf: Optimize program stats")
Fixes: ca06f55b90 ("bpf: Add per-program recursion prevention mechanism")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since sleepable programs are now executing under migrate_disable
the per-cpu maps are safe to use.
The map-in-map were ok to use in sleepable from the time sleepable
progs were introduced.
Note that non-preallocated maps are still not safe, since there is
no rcu_read_lock yet in sleepable programs and dynamically allocated
map elements are relying on rcu protection. The sleepable programs
have rcu_read_lock_trace instead. That limitation will be addresses
in the future.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-9-alexei.starovoitov@gmail.com
Add per-program counter for number of times recursion prevention mechanism
was triggered and expose it via show_fdinfo and bpf_prog_info.
Teach bpftool to print it.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-7-alexei.starovoitov@gmail.com
Since both sleepable and non-sleepable programs execute under migrate_disable
add recursion prevention mechanism to both types of programs when they're
executed via bpf trampoline.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-5-alexei.starovoitov@gmail.com
Since sleepable programs don't migrate from the cpu the excution stats can be
computed for them as well. Reuse the same infrastructure for both sleepable and
non-sleepable programs.
run_cnt -> the number of times the program was executed.
run_time_ns -> the program execution time in nanoseconds including the
off-cpu time when the program was sleeping.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-4-alexei.starovoitov@gmail.com
In older non-RT kernels migrate_disable() was the same as preempt_disable().
Since commit 74d862b682 ("sched: Make migrate_disable/enable() independent of RT")
migrate_disable() is real and doesn't prevent sleeping.
Running sleepable programs with migration disabled allows to add support for
program stats and per-cpu maps later.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-3-alexei.starovoitov@gmail.com
Move bpf_prog_stats from prog->aux into prog to avoid one extra load
in critical path of program execution.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210210033634.62081-2-alexei.starovoitov@gmail.com
For double-checked locking in bpf_common_lru_push_free(), node->type is
read outside the critical section and then re-checked under the lock.
However, concurrent writes to node->type result in data races.
For example, the following concurrent access was observed by KCSAN:
write to 0xffff88801521bc22 of 1 bytes by task 10038 on cpu 1:
__bpf_lru_node_move_in kernel/bpf/bpf_lru_list.c:91
__local_list_flush kernel/bpf/bpf_lru_list.c:298
...
read to 0xffff88801521bc22 of 1 bytes by task 10043 on cpu 0:
bpf_common_lru_push_free kernel/bpf/bpf_lru_list.c:507
bpf_lru_push_free kernel/bpf/bpf_lru_list.c:555
...
Fix the data races where node->type is read outside the critical section
(for double-checked locking) by marking the access with READ_ONCE() as
well as ensuring the variable is only accessed once.
Fixes: 3a08c2fd76 ("bpf: LRU List")
Reported-by: syzbot+3536db46dfa58c573458@syzkaller.appspotmail.com
Reported-by: syzbot+516acdb03d3e27d91bcd@syzkaller.appspotmail.com
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210209112701.3341724-1-elver@google.com
Before this patch, variable offset access to the stack was dissalowed
for regular instructions, but was allowed for "indirect" accesses (i.e.
helpers). This patch removes the restriction, allowing reading and
writing to the stack through stack pointers with variable offsets. This
makes stack-allocated buffers more usable in programs, and brings stack
pointers closer to other types of pointers.
The motivation is being able to use stack-allocated buffers for data
manipulation. When the stack size limit is sufficient, allocating
buffers on the stack is simpler than per-cpu arrays, or other
alternatives.
In unpriviledged programs, variable-offset reads and writes are
disallowed (they were already disallowed for the indirect access case)
because the speculative execution checking code doesn't support them.
Additionally, when writing through a variable-offset stack pointer, if
any pointers are in the accessible range, there's possilibities of later
leaking pointers because the write cannot be tracked precisely.
Writes with variable offset mark the whole range as initialized, even
though we don't know which stack slots are actually written. This is in
order to not reject future reads to these slots. Note that this doesn't
affect writes done through helpers; like before, helpers need the whole
stack range to be initialized to begin with.
All the stack slots are in range are considered scalars after the write;
variable-offset register spills are not tracked.
For reads, all the stack slots in the variable range needs to be
initialized (but see above about what writes do), otherwise the read is
rejected. All register spilled in stack slots that might be read are
marked as having been read, however reads through such pointers don't do
register filling; the target register will always be either a scalar or
a constant zero.
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210207011027.676572-2-andreimatei1@gmail.com
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = -1
1: R0_w=invP-1 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=invP-1 R1_w=invP-1 R10=fp0
2: (3c) w0 /= w1
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP-1 R10=fp0
3: (77) r1 >>= 32
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP4294967295 R10=fp0
4: (bf) r0 = r1
5: R0_w=invP4294967295 R1_w=invP4294967295 R10=fp0
5: (95) exit
processed 6 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
div, 64 bit: div, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (55) if r6 != 0x0 goto pc+2 2: (56) if w6 != 0x0 goto pc+2
3: (ac) w1 ^= w1 3: (ac) w1 ^= w1
4: (05) goto pc+1 4: (05) goto pc+1
5: (3f) r1 /= r6 5: (3c) w1 /= w6
6: (b7) r0 = 0 6: (b7) r0 = 0
7: (95) exit 7: (95) exit
mod, 64 bit: mod, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (15) if r6 == 0x0 goto pc+1 2: (16) if w6 == 0x0 goto pc+1
3: (9f) r1 %= r6 3: (9c) w1 %= w6
4: (b7) r0 = 0 4: (b7) r0 = 0
5: (95) exit 5: (95) exit
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes: 68fda450a7 ("bpf: fix 32-bit divide by zero")
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Anatoly has been fuzzing with kBdysch harness and reported a hang in
one of the outcomes:
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 808464450
1: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b4) w4 = 808464432
2: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP808464432 R10=fp0
2: (9c) w4 %= w0
3: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R10=fp0
3: (66) if w4 s> 0x30303030 goto pc+0
R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
propagating r0
from 6 to 7: safe
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=808464433,umax_value=2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=808464433,umax_value=2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
propagating r0
7: safe
propagating r0
from 6 to 7: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
The underlying program was xlated as follows:
# bpftool p d x i 10
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
5: (66) if w4 s> 0x30303030 goto pc+0
6: (7f) r0 >>= r0
7: (bc) w0 = w0
8: (15) if r0 == 0x0 goto pc+1
9: (9c) w4 %= w0
10: (66) if w0 s> 0x3030 goto pc+0
11: (d6) if w0 s<= 0x303030 goto pc+1
12: (05) goto pc-1
13: (95) exit
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we are
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking a closer look at the verifier analysis, the reason is that it misjudges
its pruning decision at the first 'from 6 to 7: safe' occasion. What happens
is that while both old/cur registers are marked as precise, they get misjudged
for the jmp32 case as range_within() yields true, meaning that the prior
verification path with a wider register bound could be verified successfully
and therefore the current path with a narrower register bound is deemed safe
as well whereas in reality it's not. R0 old/cur path's bounds compare as
follows:
old: smin_value=0x8000000000000000,smax_value=0x7fffffffffffffff,umin_value=0x0,umax_value=0xffffffffffffffff,var_off=(0x0; 0xffffffffffffffff)
cur: smin_value=0x8000000000000000,smax_value=0x7fffffff7fffffff,umin_value=0x0,umax_value=0xffffffff7fffffff,var_off=(0x0; 0xffffffff7fffffff)
old: s32_min_value=0x80000000,s32_max_value=0x00003030,u32_min_value=0x00000000,u32_max_value=0xffffffff
cur: s32_min_value=0x00003031,s32_max_value=0x7fffffff,u32_min_value=0x00003031,u32_max_value=0x7fffffff
The 64 bit bounds generally look okay and while the information that got
propagated from 32 to 64 bit looks correct as well, it's not precise enough
for judging a conditional jmp32. Given the latter only operates on subregisters
we also need to take these into account as well for a range_within() probe
in order to be able to prune paths. Extending the range_within() constraint
to both bounds will be able to tell us that the old signed 32 bit bounds are
not wider than the cur signed 32 bit bounds.
With the fix in place, the program will now verify the 'goto' branch case as
it should have been:
[...]
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
7: R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=12337,u32_min_value=12337,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=3158065,u32_min_value=3158065,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=3158065,u32_min_value=3158065,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 11 insns (limit 1000000) max_states_per_insn 1 total_states 1 peak_states 1 mark_read 1
The bug is quite subtle in the sense that when verifier would determine that
a given branch is dead code, it would (here: wrongly) remove these instructions
from the program and hard-wire the taken branch for privileged programs instead
of the 'goto pc-1' rewrites which will cause hard to debug problems.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Fix incorrect is_branch{32,64}_taken() analysis for the jsgt case. The return
code for both will tell the caller whether a given conditional jump is taken
or not, e.g. 1 means branch will be taken [for the involved registers] and the
goto target will be executed, 0 means branch will not be taken and instead we
fall-through to the next insn, and last but not least a -1 denotes that it is
not known at verification time whether a branch will be taken or not. Now while
the jsgt has the branch-taken case correct with reg->s32_min_value > sval, the
branch-not-taken case is off-by-one when testing for reg->s32_max_value < sval
since the branch will also be taken for reg->s32_max_value == sval. The jgt
branch analysis, for example, gets this right.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes: 4f7b3e8258 ("bpf: improve verifier branch analysis")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
There is no functionality change. This refactoring intends
to facilitate next patch change with BPF_PSEUDO_FUNC.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210204234827.1628953-1-yhs@fb.com
The BPF ringbuffer map is pre-allocated and the implementation logic
does not rely on disabling preemption or per-cpu data structures. Using
the BPF ringbuffer sleepable LSM and tracing programs does not trigger
any warnings with DEBUG_ATOMIC_SLEEP, DEBUG_PREEMPT,
PROVE_RCU and PROVE_LOCKING and LOCKDEP enabled.
This allows helpers like bpf_copy_from_user and bpf_ima_inode_hash to
write to the BPF ring buffer from sleepable BPF programs.
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210204193622.3367275-2-kpsingh@kernel.org
On 32-bit architecture, roundup_pow_of_two() can return 0 when the argument
has upper most bit set due to resulting 1UL << 32. Add a check for this case.
Fixes: d5a3b1f691 ("bpf: introduce BPF_MAP_TYPE_STACK_TRACE")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210127063653.3576-1-minhquangbui99@gmail.com
When BPF_FETCH is set, atomic instructions load a value from memory
into a register. The current verifier code first checks via
check_mem_access whether we can access the memory, and then checks
via check_reg_arg whether we can write into the register.
For loads, check_reg_arg has the side-effect of marking the
register's value as unkonwn, and check_mem_access has the side effect
of propagating bounds from memory to the register. This currently only
takes effect for stack memory.
Therefore with the current order, bounds information is thrown away,
but by simply reversing the order of check_reg_arg
vs. check_mem_access, we can instead propagate bounds smartly.
A simple test is added with an infinite loop that can only be proved
unreachable if this propagation is present. This is implemented both
with C and directly in test_verifier using assembly.
Suggested-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210202135002.4024825-1-jackmanb@google.com
!perfmon_capable() is checked before the last switch(func_id) in
bpf_base_func_proto. Thus, the cases BPF_FUNC_trace_printk and
BPF_FUNC_snprintf_btf can be moved to that last switch(func_id) to omit
the inline !perfmon_capable() checks.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210127174615.3038-1-tklauser@distanz.ch
At the moment, BPF_CGROUP_INET{4,6}_BIND hooks can rewrite user_port
to the privileged ones (< ip_unprivileged_port_start), but it will
be rejected later on in the __inet_bind or __inet6_bind.
Let's add another return value to indicate that CAP_NET_BIND_SERVICE
check should be ignored. Use the same idea as we currently use
in cgroup/egress where bit #1 indicates CN. Instead, for
cgroup/bind{4,6}, bit #1 indicates that CAP_NET_BIND_SERVICE should
be bypassed.
v5:
- rename flags to be less confusing (Andrey Ignatov)
- rework BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY to work on flags
and accept BPF_RET_SET_CN (no behavioral changes)
v4:
- Add missing IPv6 support (Martin KaFai Lau)
v3:
- Update description (Martin KaFai Lau)
- Fix capability restore in selftest (Martin KaFai Lau)
v2:
- Switch to explicit return code (Martin KaFai Lau)
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/20210127193140.3170382-1-sdf@google.com
This 'BPF_ADD' is duplicated, and I belive it should be 'BPF_AND'.
Fixes: 981f94c3e9 ("bpf: Add bitwise atomic instructions")
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Brendan Jackman <jackmanb@google.com>
Link: https://lore.kernel.org/bpf/20210127022507.23674-1-dong.menglong@zte.com.cn
Building the kernel with CONFIG_BPF_PRELOAD, and by providing a relative
path for the output directory, may fail with the following error:
$ make O=build bindeb-pkg
...
/.../linux/tools/scripts/Makefile.include:5: *** O=build does not exist. Stop.
make[7]: *** [/.../linux/kernel/bpf/preload/Makefile:9: kernel/bpf/preload/libbpf.a] Error 2
make[6]: *** [/.../linux/scripts/Makefile.build:500: kernel/bpf/preload] Error 2
make[5]: *** [/.../linux/scripts/Makefile.build:500: kernel/bpf] Error 2
make[4]: *** [/.../linux/Makefile:1799: kernel] Error 2
make[4]: *** Waiting for unfinished jobs....
In the case above, for the "bindeb-pkg" target, the error is produced by
the "dummy" check in Makefile.include, called from libbpf's Makefile.
This check changes directory to $(PWD) before checking for the existence
of $(O). But at this step we have $(PWD) pointing to "/.../linux/build",
and $(O) pointing to "build". So the Makefile.include tries in fact to
assert the existence of a directory named "/.../linux/build/build",
which does not exist.
Note that the error does not occur for all make targets and
architectures combinations. This was observed on x86 for "bindeb-pkg",
or for a regular build for UML [0].
Here are some details. The root Makefile recursively calls itself once,
after changing directory to $(O). The content for the variable $(PWD) is
preserved across recursive calls to make, so it is unchanged at this
step. For "bindeb-pkg", $(PWD) is eventually updated because the target
writes a new Makefile (as debian/rules) and calls it indirectly through
dpkg-buildpackage. This script does not preserve $(PWD), which is reset
to the current working directory when the target in debian/rules is
called.
Although not investigated, it seems likely that something similar causes
UML to change its value for $(PWD).
Non-trivial fixes could be to remove the use of $(PWD) from the "dummy"
check, or to make sure that $(PWD) and $(O) are preserved or updated to
always play well and form a valid $(PWD)/$(O) path across the different
targets and architectures. Instead, we take a simpler approach and just
update $(O) when calling libbpf's Makefile, so it points to an absolute
path which should always resolve for the "dummy" check run (through
includes) by that Makefile.
David Gow previously posted a slightly different version of this patch
as a RFC [0], two months ago or so.
[0] https://lore.kernel.org/bpf/20201119085022.3606135-1-davidgow@google.com/t/#u
Fixes: d71fa5c976 ("bpf: Add kernel module with user mode driver that populates bpffs.")
Reported-by: David Gow <davidgow@google.com>
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: Brendan Higgins <brendanhiggins@google.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/bpf/20210126161320.24561-1-quentin@isovalent.com
Some networking and keys LSM hooks are conditionally enabled
and when building the new sleepable BPF LSM hooks with those
LSM hooks disabled, the following build error occurs:
BTFIDS vmlinux
FAILED unresolved symbol bpf_lsm_socket_socketpair
To fix the error, conditionally add the relevant networking/keys
LSM hooks to the sleepable set.
Fixes: 423f16108c ("bpf: Augment the set of sleepable LSM hooks")
Signed-off-by: Mikko Ylinen <mikko.ylinen@linux.intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210125063936.89365-1-mikko.ylinen@linux.intel.com
Extend some inode methods with an additional user namespace argument. A
filesystem that is aware of idmapped mounts will receive the user
namespace the mount has been marked with. This can be used for
additional permission checking and also to enable filesystems to
translate between uids and gids if they need to. We have implemented all
relevant helpers in earlier patches.
As requested we simply extend the exisiting inode method instead of
introducing new ones. This is a little more code churn but it's mostly
mechanical and doesnt't leave us with additional inode methods.
Link: https://lore.kernel.org/r/20210121131959.646623-25-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The inode_owner_or_capable() helper determines whether the caller is the
owner of the inode or is capable with respect to that inode. Allow it to
handle idmapped mounts. If the inode is accessed through an idmapped
mount it according to the mount's user namespace. Afterwards the checks
are identical to non-idmapped mounts. If the initial user namespace is
passed nothing changes so non-idmapped mounts will see identical
behavior as before.
Similarly, allow the inode_init_owner() helper to handle idmapped
mounts. It initializes a new inode on idmapped mounts by mapping the
fsuid and fsgid of the caller from the mount's user namespace. If the
initial user namespace is passed nothing changes so non-idmapped mounts
will see identical behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-7-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The two helpers inode_permission() and generic_permission() are used by
the vfs to perform basic permission checking by verifying that the
caller is privileged over an inode. In order to handle idmapped mounts
we extend the two helpers with an additional user namespace argument.
On idmapped mounts the two helpers will make sure to map the inode
according to the mount's user namespace and then peform identical
permission checks to inode_permission() and generic_permission(). If the
initial user namespace is passed nothing changes so non-idmapped mounts
will see identical behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-6-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Add two simple helpers to check permissions on a file and path
respectively and convert over some callers. It simplifies quite a few
codepaths and also reduces the churn in later patches quite a bit.
Christoph also correctly points out that this makes codepaths (e.g.
ioctls) way easier to follow that would otherwise have to do more
complex argument passing than necessary.
Link: https://lore.kernel.org/r/20210121131959.646623-4-christian.brauner@ubuntu.com
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Put file f if inode_storage_ptr() returns NULL.
Fixes: 8ea636848a ("bpf: Implement bpf_local_storage for inodes")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210121020856.25507-1-bianpan2016@163.com
Since ctx.optlen is signed, a larger value than max_value could be
passed, as it is later on used as unsigned, which causes a WARN_ON_ONCE
in the copy_to_user.
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Signed-off-by: Loris Reiff <loris.reiff@liblor.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20210122164232.61770-2-loris.reiff@liblor.ch
A toctou issue in `__cgroup_bpf_run_filter_getsockopt` can trigger a
WARN_ON_ONCE in a check of `copy_from_user`.
`*optlen` is checked to be non-negative in the individual getsockopt
functions beforehand. Changing `*optlen` in a race to a negative value
will result in a `copy_from_user(ctx.optval, optval, ctx.optlen)` with
`ctx.optlen` being a negative integer.
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Signed-off-by: Loris Reiff <loris.reiff@liblor.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20210122164232.61770-1-loris.reiff@liblor.ch
When we attach any cgroup hook, the rest (even if unused/unattached) start
to contribute small overhead. In particular, the one we want to avoid is
__cgroup_bpf_run_filter_skb which does two redirections to get to
the cgroup and pushes/pulls skb.
Let's split cgroup_bpf_enabled to be per-attach to make sure
only used attach types trigger.
I've dropped some existing high-level cgroup_bpf_enabled in some
places because BPF_PROG_CGROUP_XXX_RUN macros usually have another
cgroup_bpf_enabled check.
I also had to copy-paste BPF_CGROUP_RUN_SA_PROG_LOCK for
GETPEERNAME/GETSOCKNAME because type for cgroup_bpf_enabled[type]
has to be constant and known at compile time.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210115163501.805133-4-sdf@google.com
When we attach a bpf program to cgroup/getsockopt any other getsockopt()
syscall starts incurring kzalloc/kfree cost.
Let add a small buffer on the stack and use it for small (majority)
{s,g}etsockopt values. The buffer is small enough to fit into
the cache line and cover the majority of simple options (most
of them are 4 byte ints).
It seems natural to do the same for setsockopt, but it's a bit more
involved when the BPF program modifies the data (where we have to
kmalloc). The assumption is that for the majority of setsockopt
calls (which are doing pure BPF options or apply policy) this
will bring some benefit as well.
Without this patch (we remove about 1% __kmalloc):
3.38% 0.07% tcp_mmap [kernel.kallsyms] [k] __cgroup_bpf_run_filter_getsockopt
|
--3.30%--__cgroup_bpf_run_filter_getsockopt
|
--0.81%--__kmalloc
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210115163501.805133-3-sdf@google.com
Add custom implementation of getsockopt hook for TCP_ZEROCOPY_RECEIVE.
We skip generic hooks for TCP_ZEROCOPY_RECEIVE and have a custom
call in do_tcp_getsockopt using the on-stack data. This removes
3% overhead for locking/unlocking the socket.
Without this patch:
3.38% 0.07% tcp_mmap [kernel.kallsyms] [k] __cgroup_bpf_run_filter_getsockopt
|
--3.30%--__cgroup_bpf_run_filter_getsockopt
|
--0.81%--__kmalloc
With the patch applied:
0.52% 0.12% tcp_mmap [kernel.kallsyms] [k] __cgroup_bpf_run_filter_getsockopt_kern
Note, exporting uapi/tcp.h requires removing netinet/tcp.h
from test_progs.h because those headers have confliciting
definitions.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210115163501.805133-2-sdf@google.com
llvm patch https://reviews.llvm.org/D84002 permitted
to emit empty rodata datasec if the elf .rodata section
contains read-only data from local variables. These
local variables will be not emitted as BTF_KIND_VARs
since llvm converted these local variables as
static variables with private linkage without debuginfo
types. Such an empty rodata datasec will make
skeleton code generation easy since for skeleton
a rodata struct will be generated if there is a
.rodata elf section. The existence of a rodata
btf datasec is also consistent with the existence
of a rodata map created by libbpf.
The btf with such an empty rodata datasec will fail
in the kernel though as kernel will reject a datasec
with zero vlen and zero size. For example, for the below code,
int sys_enter(void *ctx)
{
int fmt[6] = {1, 2, 3, 4, 5, 6};
int dst[6];
bpf_probe_read(dst, sizeof(dst), fmt);
return 0;
}
We got the below btf (bpftool btf dump ./test.o):
[1] PTR '(anon)' type_id=0
[2] FUNC_PROTO '(anon)' ret_type_id=3 vlen=1
'ctx' type_id=1
[3] INT 'int' size=4 bits_offset=0 nr_bits=32 encoding=SIGNED
[4] FUNC 'sys_enter' type_id=2 linkage=global
[5] INT 'char' size=1 bits_offset=0 nr_bits=8 encoding=SIGNED
[6] ARRAY '(anon)' type_id=5 index_type_id=7 nr_elems=4
[7] INT '__ARRAY_SIZE_TYPE__' size=4 bits_offset=0 nr_bits=32 encoding=(none)
[8] VAR '_license' type_id=6, linkage=global-alloc
[9] DATASEC '.rodata' size=0 vlen=0
[10] DATASEC 'license' size=0 vlen=1
type_id=8 offset=0 size=4
When loading the ./test.o to the kernel with bpftool,
we see the following error:
libbpf: Error loading BTF: Invalid argument(22)
libbpf: magic: 0xeb9f
...
[6] ARRAY (anon) type_id=5 index_type_id=7 nr_elems=4
[7] INT __ARRAY_SIZE_TYPE__ size=4 bits_offset=0 nr_bits=32 encoding=(none)
[8] VAR _license type_id=6 linkage=1
[9] DATASEC .rodata size=24 vlen=0 vlen == 0
libbpf: Error loading .BTF into kernel: -22. BTF is optional, ignoring.
Basically, libbpf changed .rodata datasec size to 24 since elf .rodata
section size is 24. The kernel then rejected the BTF since vlen = 0.
Note that the above kernel verifier failure can be worked around with
changing local variable "fmt" to a static or global, optionally const, variable.
This patch permits a datasec with vlen = 0 in kernel.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210119153519.3901963-1-yhs@fb.com
Introduce __xdp_build_skb_from_frame utility routine to build
the skb from xdp_frame. Rely on __xdp_build_skb_from_frame in
cpumap code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/4f9f4c6b3dd3933770c617eb6689dbc0c6e25863.1610475660.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix incorrect signed_{sub,add32}_overflows() input types (and a related buggy
comment). It looks like this might have slipped in via copy/paste issue, also
given prior to 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
the signature of signed_sub_overflows() had s64 a and s64 b as its input args
whereas now they are truncated to s32. Thus restore proper types. Also, the case
of signed_add32_overflows() is not consistent to signed_sub32_overflows(). Both
have s32 as inputs, therefore align the former.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: De4dCr0w <sa516203@mail.ustc.edu.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
I assume this was obtained by copy/paste. Point it to bpf_map_peek_elem()
instead of bpf_map_pop_elem(). In practice it may have been less likely
hit when under JIT given shielded via 84430d4232 ("bpf, verifier: avoid
retpoline for map push/pop/peek operation").
Fixes: f1a2e44a3a ("bpf: add queue and stack maps")
Signed-off-by: Mircea Cirjaliu <mcirjaliu@bitdefender.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mauricio Vasquez <mauriciovasquezbernal@gmail.com>
Link: https://lore.kernel.org/bpf/AM7PR02MB6082663DFDCCE8DA7A6DD6B1BBA30@AM7PR02MB6082.eurprd02.prod.outlook.com
It's possible to have other build id types (other than default SHA1).
Currently there's also ld support for MD5 build id.
Adding size argument to build_id_parse function, that returns (if defined)
size of the parsed build id, so we can recognize the build id type.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210114134044.1418404-3-jolsa@kernel.org
Moving stack_map_get_build_id into lib with
declaration in linux/buildid.h header:
int build_id_parse(struct vm_area_struct *vma, unsigned char *build_id);
This function returns build id for given struct vm_area_struct.
There is no functional change to stack_map_get_build_id function.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210114134044.1418404-2-jolsa@kernel.org
This adds instructions for
atomic[64]_[fetch_]and
atomic[64]_[fetch_]or
atomic[64]_[fetch_]xor
All these operations are isomorphic enough to implement with the same
verifier, interpreter, and x86 JIT code, hence being a single commit.
The main interesting thing here is that x86 doesn't directly support
the fetch_ version these operations, so we need to generate a CMPXCHG
loop in the JIT. This requires the use of two temporary registers,
IIUC it's safe to use BPF_REG_AX and x86's AUX_REG for this purpose.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-10-jackmanb@google.com
Since the atomic operations that are added in subsequent commits are
all isomorphic with BPF_ADD, pull out a macro to avoid the
interpreter becoming dominated by lines of atomic-related code.
Note that this sacrificies interpreter performance (combining
STX_ATOMIC_W and STX_ATOMIC_DW into single switch case means that we
need an extra conditional branch to differentiate them) in favour of
compact and (relatively!) simple C code.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-9-jackmanb@google.com
This adds two atomic opcodes, both of which include the BPF_FETCH
flag. XCHG without the BPF_FETCH flag would naturally encode
atomic_set. This is not supported because it would be of limited
value to userspace (it doesn't imply any barriers). CMPXCHG without
BPF_FETCH woulud be an atomic compare-and-write. We don't have such
an operation in the kernel so it isn't provided to BPF either.
There are two significant design decisions made for the CMPXCHG
instruction:
- To solve the issue that this operation fundamentally has 3
operands, but we only have two register fields. Therefore the
operand we compare against (the kernel's API calls it 'old') is
hard-coded to be R0. x86 has similar design (and A64 doesn't
have this problem).
A potential alternative might be to encode the other operand's
register number in the immediate field.
- The kernel's atomic_cmpxchg returns the old value, while the C11
userspace APIs return a boolean indicating the comparison
result. Which should BPF do? A64 returns the old value. x86 returns
the old value in the hard-coded register (and also sets a
flag). That means return-old-value is easier to JIT, so that's
what we use.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-8-jackmanb@google.com
The BPF_FETCH field can be set in bpf_insn.imm, for BPF_ATOMIC
instructions, in order to have the previous value of the
atomically-modified memory location loaded into the src register
after an atomic op is carried out.
Suggested-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-7-jackmanb@google.com
I can't find a reason why this code is in resolve_pseudo_ldimm64;
since I'll be modifying it in a subsequent commit, tidy it up.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-6-jackmanb@google.com
A subsequent patch will add additional atomic operations. These new
operations will use the same opcode field as the existing XADD, with
the immediate discriminating different operations.
In preparation, rename the instruction mode BPF_ATOMIC and start
calling the zero immediate BPF_ADD.
This is possible (doesn't break existing valid BPF progs) because the
immediate field is currently reserved MBZ and BPF_ADD is zero.
All uses are removed from the tree but the BPF_XADD definition is
kept around to avoid breaking builds for people including kernel
headers.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Link: https://lore.kernel.org/bpf/20210114181751.768687-5-jackmanb@google.com
Add support for pointer to mem register spilling, to allow the verifier
to track pointers to valid memory addresses. Such pointers are returned
for example by a successful call of the bpf_ringbuf_reserve helper.
The patch was partially contributed by CyberArk Software, Inc.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Suggested-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Gilad Reti <gilad.reti@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210113053810.13518-1-gilad.reti@gmail.com
Add support for directly accessing kernel module variables from BPF programs
using special ldimm64 instructions. This functionality builds upon vmlinux
ksym support, but extends ldimm64 with src_reg=BPF_PSEUDO_BTF_ID to allow
specifying kernel module BTF's FD in insn[1].imm field.
During BPF program load time, verifier will resolve FD to BTF object and will
take reference on BTF object itself and, for module BTFs, corresponding module
as well, to make sure it won't be unloaded from under running BPF program. The
mechanism used is similar to how bpf_prog keeps track of used bpf_maps.
One interesting change is also in how per-CPU variable is determined. The
logic is to find .data..percpu data section in provided BTF, but both vmlinux
and module each have their own .data..percpu entries in BTF. So for module's
case, the search for DATASEC record needs to look at only module's added BTF
types. This is implemented with custom search function.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/bpf/20210112075520.4103414-6-andrii@kernel.org
The error message here is misleading, the argument will be rejected unless
it is a known constant.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210112123913.2016804-1-jackmanb@google.com
Some modules don't declare any new types and end up with an empty BTF,
containing only valid BTF header and no types or strings sections. This
currently causes BTF validation error. There is nothing wrong with such BTF,
so fix the issue by allowing module BTFs with no types or strings.
Fixes: 36e68442d1 ("bpf: Load and verify kernel module BTFs")
Reported-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210110070341.1380086-1-andrii@kernel.org
optlen == 0 indicates that the kernel should ignore BPF buffer
and use the original one from the user. We, however, forget
to free the temporary buffer that we've allocated for BPF.
Fixes: d8fe449a9c ("bpf: Don't return EINVAL from {get,set}sockopt when optlen > PAGE_SIZE")
Reported-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210112162829.775079-1-sdf@google.com
The verifier allows ARG_PTR_TO_BTF_ID helper arguments to be NULL, so
helper implementations need to check this before dereferencing them.
This was already fixed for the socket storage helpers but not for task
and inode.
The issue can be reproduced by attaching an LSM program to
inode_rename hook (called when moving files) which tries to get the
inode of the new file without checking for its nullness and then trying
to move an existing file to a new path:
mv existing_file new_file_does_not_exist
The report including the sample program and the steps for reproducing
the bug:
https://lore.kernel.org/bpf/CANaYP3HWkH91SN=wTNO9FL_2ztHfqcXKX38SSE-JJ2voh+vssw@mail.gmail.com
Fixes: 4cf1bc1f10 ("bpf: Implement task local storage")
Fixes: 8ea636848a ("bpf: Implement bpf_local_storage for inodes")
Reported-by: Gilad Reti <gilad.reti@gmail.com>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210112075525.256820-3-kpsingh@kernel.org
The bpf_tracing_prog_attach error path calls bpf_prog_put
on prog, which causes refcount underflow when it's called
from link_create function.
link_create
prog = bpf_prog_get <-- get
...
tracing_bpf_link_attach(prog..
bpf_tracing_prog_attach(prog..
out_put_prog:
bpf_prog_put(prog); <-- put
if (ret < 0)
bpf_prog_put(prog); <-- put
Removing bpf_prog_put call from bpf_tracing_prog_attach
and making sure its callers call it instead.
Fixes: 4a1e7c0c63 ("bpf: Support attaching freplace programs to multiple attach points")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210111191650.1241578-1-jolsa@kernel.org
This program does not use argp (which is a glibcism). Instead include <errno.h>
directly, which was pulled in by <argp.h>.
Signed-off-by: Leah Neukirchen <leah@vuxu.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201216100306.30942-1-leah@vuxu.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Latest bpf tree has a bug for bpf_iter selftest:
$ ./test_progs -n 4/25
test_bpf_sk_storage_get:PASS:bpf_iter_bpf_sk_storage_helpers__open_and_load 0 nsec
test_bpf_sk_storage_get:PASS:socket 0 nsec
...
do_dummy_read:PASS:read 0 nsec
test_bpf_sk_storage_get:FAIL:bpf_map_lookup_elem map value wasn't set correctly
(expected 1792, got -1, err=0)
#4/25 bpf_sk_storage_get:FAIL
#4 bpf_iter:FAIL
Summary: 0/0 PASSED, 0 SKIPPED, 2 FAILED
When doing merge conflict resolution, Commit 4bfc471484 missed to
save curr_task to seq_file private data. The task pointer in seq_file
private data is passed to bpf program. This caused NULL-pointer task
passed to bpf program which will immediately return upon checking
whether task pointer is NULL.
This patch added back the assignment of curr_task to seq_file private
data and fixed the issue.
Fixes: 4bfc471484 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20201231052418.577024-1-yhs@fb.com
Daniel Borkmann says:
====================
pull-request: bpf 2020-12-28
The following pull-request contains BPF updates for your *net* tree.
There is a small merge conflict between bpf tree commit 69ca310f34
("bpf: Save correct stopping point in file seq iteration") and net tree
commit 66ed594409 ("bpf/task_iter: In task_file_seq_get_next use
task_lookup_next_fd_rcu"). The get_files_struct() does not exist anymore
in net, so take the hunk in HEAD and add the `info->tid = curr_tid` to
the error path:
[...]
curr_task = task_seq_get_next(ns, &curr_tid, true);
if (!curr_task) {
info->task = NULL;
info->tid = curr_tid;
return NULL;
}
/* set info->task and info->tid */
[...]
We've added 10 non-merge commits during the last 9 day(s) which contain
a total of 11 files changed, 75 insertions(+), 20 deletions(-).
The main changes are:
1) Various AF_XDP fixes such as fill/completion ring leak on failed bind and
fixing a race in skb mode's backpressure mechanism, from Magnus Karlsson.
2) Fix latency spikes on lockdep enabled kernels by adding a rescheduling
point to BPF hashtab initialization, from Eric Dumazet.
3) Fix a splat in task iterator by saving the correct stopping point in the
seq file iteration, from Jonathan Lemon.
4) Fix BPF maps selftest by adding retries in case hashtab returns EBUSY
errors on update/deletes, from Andrii Nakryiko.
5) Fix BPF selftest error reporting to something more user friendly if the
vmlinux BTF cannot be found, from Kamal Mostafa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of directly comparing task->tgid and task->pid, use the
thread_group_leader() helper. This helps with readability, and
there should be no functional change.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201218185032.2464558-3-jonathan.lemon@gmail.com
We noticed that with a LOCKDEP enabled kernel,
allocating a hash table with 65536 buckets would
use more than 60ms.
htab_init_buckets() runs from process context,
it is safe to schedule to avoid latency spikes.
Fixes: c50eb518e2 ("bpf: Use separate lockdep class for each hashtab")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201221192506.707584-1-eric.dumazet@gmail.com
Pull execve updates from Eric Biederman:
"This set of changes ultimately fixes the interaction of posix file
lock and exec. Fundamentally most of the change is just moving where
unshare_files is called during exec, and tweaking the users of
files_struct so that the count of files_struct is not unnecessarily
played with.
Along the way fcheck and related helpers were renamed to more
accurately reflect what they do.
There were also many other small changes that fell out, as this is the
first time in a long time much of this code has been touched.
Benchmarks haven't turned up any practical issues but Al Viro has
observed a possibility for a lot of pounding on task_lock. So I have
some changes in progress to convert put_files_struct to always rcu
free files_struct. That wasn't ready for the merge window so that will
have to wait until next time"
* 'exec-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
exec: Move io_uring_task_cancel after the point of no return
coredump: Document coredump code exclusively used by cell spufs
file: Remove get_files_struct
file: Rename __close_fd_get_file close_fd_get_file
file: Replace ksys_close with close_fd
file: Rename __close_fd to close_fd and remove the files parameter
file: Merge __alloc_fd into alloc_fd
file: In f_dupfd read RLIMIT_NOFILE once.
file: Merge __fd_install into fd_install
proc/fd: In fdinfo seq_show don't use get_files_struct
bpf/task_iter: In task_file_seq_get_next use task_lookup_next_fd_rcu
proc/fd: In proc_readfd_common use task_lookup_next_fd_rcu
file: Implement task_lookup_next_fd_rcu
kcmp: In get_file_raw_ptr use task_lookup_fd_rcu
proc/fd: In tid_fd_mode use task_lookup_fd_rcu
file: Implement task_lookup_fd_rcu
file: Rename fcheck lookup_fd_rcu
file: Replace fcheck_files with files_lookup_fd_rcu
file: Factor files_lookup_fd_locked out of fcheck_files
file: Rename __fcheck_files to files_lookup_fd_raw
...
Core:
- support "prefer busy polling" NAPI operation mode, where we defer softirq
for some time expecting applications to periodically busy poll
- AF_XDP: improve efficiency by more batching and hindering
the adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or unaligned
reads making zero copy a performance win for much smaller messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined in
IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which
also allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to
a central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GXs1
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- support "prefer busy polling" NAPI operation mode, where we defer
softirq for some time expecting applications to periodically busy
poll
- AF_XDP: improve efficiency by more batching and hindering the
adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or
unaligned reads making zero copy a performance win for much smaller
messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use
bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined
in IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver
internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej
Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which also
allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to a
central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support"
* tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1922 commits)
net: hns3: fix expression that is currently always true
net: fix proc_fs init handling in af_packet and tls
nfc: pn533: convert comma to semicolon
af_vsock: Assign the vsock transport considering the vsock address flags
af_vsock: Set VMADDR_FLAG_TO_HOST flag on the receive path
vsock_addr: Check for supported flag values
vm_sockets: Add VMADDR_FLAG_TO_HOST vsock flag
vm_sockets: Add flags field in the vsock address data structure
net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled
tcp: Add logic to check for SYN w/ data in tcp_simple_retransmit
net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
nfc: s3fwrn5: Release the nfc firmware
net: vxget: clean up sparse warnings
mlxsw: spectrum_router: Use eXtended mezzanine to offload IPv4 router
mlxsw: spectrum: Set KVH XLT cache mode for Spectrum2/3
mlxsw: spectrum_router_xm: Introduce basic XM cache flushing
mlxsw: reg: Add Router LPM Cache Enable Register
mlxsw: reg: Add Router LPM Cache ML Delete Register
mlxsw: spectrum_router_xm: Implement L-value tracking for M-index
mlxsw: reg: Add XM Router M Table Register
...
- migrate_disable/enable() support which originates from the RT tree and
is now a prerequisite for the new preemptible kmap_local() API which aims
to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
-----BEGIN PGP SIGNATURE-----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=Oz1V
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Thomas Gleixner:
- migrate_disable/enable() support which originates from the RT tree
and is now a prerequisite for the new preemptible kmap_local() API
which aims to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
* tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (61 commits)
sched/fair: Trivial correction of the newidle_balance() comment
sched/fair: Clear SMT siblings after determining the core is not idle
sched: Fix kernel-doc markup
x86: Print ratio freq_max/freq_base used in frequency invariance calculations
x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC
x86, sched: Calculate frequency invariance for AMD systems
irq_work: Optimize irq_work_single()
smp: Cleanup smp_call_function*()
irq_work: Cleanup
sched: Limit the amount of NUMA imbalance that can exist at fork time
sched/numa: Allow a floating imbalance between NUMA nodes
sched: Avoid unnecessary calculation of load imbalance at clone time
sched/numa: Rename nr_running and break out the magic number
sched: Make migrate_disable/enable() independent of RT
sched/topology: Condition EAS enablement on FIE support
arm64: Rebuild sched domains on invariance status changes
sched/topology,schedutil: Wrap sched domains rebuild
sched/uclamp: Allow to reset a task uclamp constraint value
sched/core: Fix typos in comments
Documentation: scheduler: fix information on arch SD flags, sched_domain and sched_debug
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-12-14
1) Expose bpf_sk_storage_*() helpers to iterator programs, from Florent Revest.
2) Add AF_XDP selftests based on veth devs to BPF selftests, from Weqaar Janjua.
3) Support for finding BTF based kernel attach targets through libbpf's
bpf_program__set_attach_target() API, from Andrii Nakryiko.
4) Permit pointers on stack for helper calls in the verifier, from Yonghong Song.
5) Fix overflows in hash map elem size after rlimit removal, from Eric Dumazet.
6) Get rid of direct invocation of llc in BPF selftests, from Andrew Delgadillo.
7) Fix xsk_recvmsg() to reorder socket state check before access, from Björn Töpel.
8) Add new libbpf API helper to retrieve ring buffer epoll fd, from Brendan Jackman.
9) Batch of minor BPF selftest improvements all over the place, from Florian Lehner,
KP Singh, Jiri Olsa and various others.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (31 commits)
selftests/bpf: Add a test for ptr_to_map_value on stack for helper access
bpf: Permits pointers on stack for helper calls
libbpf: Expose libbpf ring_buffer epoll_fd
selftests/bpf: Add set_attach_target() API selftest for module target
libbpf: Support modules in bpf_program__set_attach_target() API
selftests/bpf: Silence ima_setup.sh when not running in verbose mode.
selftests/bpf: Drop the need for LLVM's llc
selftests/bpf: fix bpf_testmod.ko recompilation logic
samples/bpf: Fix possible hang in xdpsock with multiple threads
selftests/bpf: Make selftest compilation work on clang 11
selftests/bpf: Xsk selftests - adding xdpxceiver to .gitignore
selftests/bpf: Drop tcp-{client,server}.py from Makefile
selftests/bpf: Xsk selftests - Bi-directional Sockets - SKB, DRV
selftests/bpf: Xsk selftests - Socket Teardown - SKB, DRV
selftests/bpf: Xsk selftests - DRV POLL, NOPOLL
selftests/bpf: Xsk selftests - SKB POLL, NOPOLL
selftests/bpf: Xsk selftests framework
bpf: Only provide bpf_sock_from_file with CONFIG_NET
bpf: Return -ENOTSUPP when attaching to non-kernel BTF
xsk: Validate socket state in xsk_recvmsg, prior touching socket members
...
====================
Link: https://lore.kernel.org/r/20201214214316.20642-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when checking stack memory accessed by helper calls,
for spills, only PTR_TO_BTF_ID and SCALAR_VALUE are
allowed.
Song discovered an issue where the below bpf program
int dump_task(struct bpf_iter__task *ctx)
{
struct seq_file *seq = ctx->meta->seq;
static char[] info = "abc";
BPF_SEQ_PRINTF(seq, "%s\n", info);
return 0;
}
may cause a verifier failure.
The verifier output looks like:
; struct seq_file *seq = ctx->meta->seq;
1: (79) r1 = *(u64 *)(r1 +0)
; BPF_SEQ_PRINTF(seq, "%s\n", info);
2: (18) r2 = 0xffff9054400f6000
4: (7b) *(u64 *)(r10 -8) = r2
5: (bf) r4 = r10
;
6: (07) r4 += -8
; BPF_SEQ_PRINTF(seq, "%s\n", info);
7: (18) r2 = 0xffff9054400fe000
9: (b4) w3 = 4
10: (b4) w5 = 8
11: (85) call bpf_seq_printf#126
R1_w=ptr_seq_file(id=0,off=0,imm=0) R2_w=map_value(id=0,off=0,ks=4,vs=4,imm=0)
R3_w=inv4 R4_w=fp-8 R5_w=inv8 R10=fp0 fp-8_w=map_value
last_idx 11 first_idx 0
regs=8 stack=0 before 10: (b4) w5 = 8
regs=8 stack=0 before 9: (b4) w3 = 4
invalid indirect read from stack off -8+0 size 8
Basically, the verifier complains the map_value pointer at "fp-8" location.
To fix the issue, if env->allow_ptr_leaks is true, let us also permit
pointers on the stack to be accessible by the helper.
Reported-by: Song Liu <songliubraving@fb.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201210013349.943719-1-yhs@fb.com
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove bpf_ prefix, which causes these helpers to be reported in verifier
dump as bpf_bpf_this_cpu_ptr() and bpf_bpf_per_cpu_ptr(), respectively. Lets
fix it as long as it is still possible before UAPI freezes on these helpers.
Fixes: eaa6bcb71e ("bpf: Introduce bpf_per_cpu_ptr()")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 64-bit signed bounds should not affect 32-bit signed bounds unless the
verifier knows that upper 32-bits are either all 1s or all 0s. For example the
register with smin_value==1 doesn't mean that s32_min_value is also equal to 1,
since smax_value could be larger than 32-bit subregister can hold.
The verifier refines the smax/s32_max return value from certain helpers in
do_refine_retval_range(). Teach the verifier to recognize that smin/s32_min
value is also bounded. When both smin and smax bounds fit into 32-bit
subregister the verifier can propagate those bounds.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When discussing[1] exec and posix file locks it was realized that none
of the callers of get_files_struct fundamentally needed to call
get_files_struct, and that by switching them to helper functions
instead it will both simplify their code and remove unnecessary
increments of files_struct.count. Those unnecessary increments can
result in exec unnecessarily unsharing files_struct which breaking
posix locks, and it can result in fget_light having to fallback to
fget reducing system performance.
Using task_lookup_next_fd_rcu simplifies task_file_seq_get_next, by
moving the checking for the maximum file descritor into the generic
code, and by remvoing the need for capturing and releasing a reference
on files_struct. As the reference count of files_struct no longer
needs to be maintained bpf_iter_seq_task_file_info can have it's files
member removed and task_file_seq_get_next no longer needs it's fstruct
argument.
The curr_fd local variable does need to become unsigned to be used
with fnext_task. As curr_fd is assigned from and assigned a u32
making curr_fd an unsigned int won't cause problems and might prevent
them.
[1] https://lkml.kernel.org/r/20180915160423.GA31461@redhat.com
Suggested-by: Oleg Nesterov <oleg@redhat.com>
v1: https://lkml.kernel.org/r/20200817220425.9389-11-ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20201120231441.29911-16-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This change renames fcheck_files to files_lookup_fd_rcu. All of the
remaining callers take the rcu_read_lock before calling this function
so the _rcu suffix is appropriate. This change also tightens up the
debug check to verify that all callers hold the rcu_read_lock.
All callers that used to call files_check with the files->file_lock
held have now been changed to call files_lookup_fd_locked.
This change of name has helped remind me of which locks and which
guarantees are in place helping me to catch bugs later in the
patchset.
The need for better names became apparent in the last round of
discussion of this set of changes[1].
[1] https://lkml.kernel.org/r/CAHk-=wj8BQbgJFLa+J0e=iT-1qpmCRTbPAJ8gd6MJQ=kbRPqyQ@mail.gmail.com
Link: https://lkml.kernel.org/r/20201120231441.29911-9-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Use the helper fget_task to simplify bpf_task_fd_query.
As well as simplifying the code this removes one unnecessary increment of
struct files_struct. This unnecessary increment of files_struct.count can
result in exec unnecessarily unsharing files_struct and breaking posix
locks, and it can result in fget_light having to fallback to fget reducing
performance.
This simplification comes from the observation that none of the
callers of get_files_struct actually need to call get_files_struct
that was made when discussing[1] exec and posix file locks.
[1] https://lkml.kernel.org/r/20180915160423.GA31461@redhat.com
Suggested-by: Oleg Nesterov <oleg@redhat.com>
v1: https://lkml.kernel.org/r/20200817220425.9389-5-ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20201120231441.29911-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Return -ENOTSUPP if tracing BPF program is attempted to be attached with
specified attach_btf_obj_fd pointing to non-kernel (neither vmlinux nor
module) BTF object. This scenario might be supported in the future and isn't
outright invalid, so -EINVAL isn't the most appropriate error code.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201208064326.667389-1-andrii@kernel.org
__htab_map_lookup_and_delete_batch() stores a user pointer in the local
variable ubatch and uses that in copy_{from,to}_user(), but ubatch misses a
__user annotation.
So, sparse warns in the various assignments and uses of ubatch:
kernel/bpf/hashtab.c:1415:24: warning: incorrect type in initializer
(different address spaces)
kernel/bpf/hashtab.c:1415:24: expected void *ubatch
kernel/bpf/hashtab.c:1415:24: got void [noderef] __user *
kernel/bpf/hashtab.c:1444:46: warning: incorrect type in argument 2
(different address spaces)
kernel/bpf/hashtab.c:1444:46: expected void const [noderef] __user *from
kernel/bpf/hashtab.c:1444:46: got void *ubatch
kernel/bpf/hashtab.c:1608:16: warning: incorrect type in assignment
(different address spaces)
kernel/bpf/hashtab.c:1608:16: expected void *ubatch
kernel/bpf/hashtab.c:1608:16: got void [noderef] __user *
kernel/bpf/hashtab.c:1609:26: warning: incorrect type in argument 1
(different address spaces)
kernel/bpf/hashtab.c:1609:26: expected void [noderef] __user *to
kernel/bpf/hashtab.c:1609:26: got void *ubatch
Add the __user annotation to repair this chain of propagating __user
annotations in __htab_map_lookup_and_delete_batch().
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201207123720.19111-1-lukas.bulwahn@gmail.com
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add ability for user-space programs to specify non-vmlinux BTF when attaching
BTF-powered BPF programs: raw_tp, fentry/fexit/fmod_ret, LSM, etc. For this,
attach_prog_fd (now with the alias name attach_btf_obj_fd) should specify FD
of a module or vmlinux BTF object. For backwards compatibility reasons,
0 denotes vmlinux BTF. Only kernel BTF (vmlinux or module) can be specified.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201203204634.1325171-11-andrii@kernel.org
Remove a permeating assumption thoughout BPF verifier of vmlinux BTF. Instead,
wherever BTF type IDs are involved, also track the instance of struct btf that
goes along with the type ID. This allows to gradually add support for kernel
module BTFs and using/tracking module types across BPF helper calls and
registers.
This patch also renames btf_id() function to btf_obj_id() to minimize naming
clash with using btf_id to denote BTF *type* ID, rather than BTF *object*'s ID.
Also, altough btf_vmlinux can't get destructed and thus doesn't need
refcounting, module BTFs need that, so apply BTF refcounting universally when
BPF program is using BTF-powered attachment (tp_btf, fentry/fexit, etc). This
makes for simpler clean up code.
Now that BTF type ID is not enough to uniquely identify a BTF type, extend BPF
trampoline key to include BTF object ID. To differentiate that from target
program BPF ID, set 31st bit of type ID. BTF type IDs (at least currently) are
not allowed to take full 32 bits, so there is no danger of confusing that bit
with a valid BTF type ID.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201203204634.1325171-10-andrii@kernel.org
Do not use rlimit-based memory accounting for bpf progs. It has been
replaced with memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-34-guro@fb.com
Remove rlimit-based accounting infrastructure code, which is not used
anymore.
To provide a backward compatibility, use an approximation of the
bpf map memory footprint as a "memlock" value, available to a user
via map info. The approximation is based on the maximal number of
elements and key and value sizes.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-33-guro@fb.com
Do not use rlimit-based memory accounting for bpf local storage maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-32-guro@fb.com
Do not use rlimit-based memory accounting for stackmap maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-30-guro@fb.com
Do not use rlimit-based memory accounting for bpf ringbuffer.
It has been replaced with the memcg-based memory accounting.
bpf_ringbuf_alloc() can't return anything except ERR_PTR(-ENOMEM)
and a valid pointer, so to simplify the code make it return NULL
in the first case. This allows to drop a couple of lines in
ringbuf_map_alloc() and also makes it look similar to other memory
allocating function like kmalloc().
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-28-guro@fb.com
Do not use rlimit-based memory accounting for reuseport_array maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-27-guro@fb.com
Do not use rlimit-based memory accounting for queue_stack maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-26-guro@fb.com
Do not use rlimit-based memory accounting for lpm_trie maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-25-guro@fb.com
Do not use rlimit-based memory accounting for hashtab maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-24-guro@fb.com
Do not use rlimit-based memory accounting for devmap maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-23-guro@fb.com
Do not use rlimit-based memory accounting for cgroup storage maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-22-guro@fb.com
Do not use rlimit-based memory accounting for cpumap maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-21-guro@fb.com
Do not use rlimit-based memory accounting for bpf_struct_ops maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-20-guro@fb.com
Do not use rlimit-based memory accounting for arraymap maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-19-guro@fb.com
Account memory used by cgroup storage maps including metadata
structures.
Account the percpu memory for the percpu flavor of cgroup storage.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-11-guro@fb.com
This patch enables memcg-based memory accounting for memory allocated
by __bpf_map_area_alloc(), which is used by many types of bpf maps for
large initial memory allocations.
Please note, that __bpf_map_area_alloc() should not be used outside of
map creation paths without setting the active memory cgroup to the
map's memory cgroup.
Following patches in the series will refine the accounting for
some of the map types.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-8-guro@fb.com
Bpf maps can be updated from an interrupt context and in such
case there is no process which can be charged. It makes the memory
accounting of bpf maps non-trivial.
Fortunately, after commit 4127c6504f ("mm: kmem: enable kernel
memcg accounting from interrupt contexts") and commit b87d8cefe4
("mm, memcg: rework remote charging API to support nesting")
it's finally possible.
To make the ownership model simple and consistent, when the map
is created, the memory cgroup of the current process is recorded.
All subsequent allocations related to the bpf map are charged to
the same memory cgroup. It includes allocations made by any processes
(even if they do belong to a different cgroup) and from interrupts.
This commit introduces 3 new helpers, which will be used by following
commits to enable the accounting of bpf maps memory:
- bpf_map_kmalloc_node()
- bpf_map_kzalloc()
- bpf_map_alloc_percpu()
They are wrapping popular memory allocation functions. They set
the active memory cgroup to the map's memory cgroup and add
__GFP_ACCOUNT to the passed gfp flags. Then they call into
the corresponding memory allocation function and restore
the original active memory cgroup.
These helpers are supposed to use everywhere except the map creation
path. During the map creation when the map structure is allocated by
itself, it cannot be passed to those helpers. In those cases default
memory allocation function will be used with the __GFP_ACCOUNT flag.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-7-guro@fb.com
Include memory used by bpf programs into the memcg-based accounting.
This includes the memory used by programs itself, auxiliary data,
statistics and bpf line info. A memory cgroup containing the
process which loads the program is getting charged.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-6-guro@fb.com
Provide a wrapper function to get the IMA hash of an inode. This helper
is useful in fingerprinting files (e.g executables on execution) and
using these fingerprints in detections like an executable unlinking
itself.
Since the ima_inode_hash can sleep, it's only allowed for sleepable
LSM hooks.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201124151210.1081188-3-kpsingh@chromium.org
The current implementation uses a number of gotos to implement a loop
and different paths within the loop, which makes the code less readable
than it would be with an explicit while-loop. This patch also replaces a
chain of if/if-elses keyed on the same expression with a switch
statement.
No change in behaviour is intended.
Signed-off-by: Wedson Almeida Filho <wedsonaf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201121015509.3594191-1-wedsonaf@google.com
Get rid of the __call_single_node union and clean up the API a little
to avoid external code relying on the structure layout as much.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Simplify task_file_seq_get_next() by removing two in/out arguments: task
and fstruct. Use info->task and info->files instead.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201120002833.2481110-1-songliubraving@fb.com
The helper uses CLOCK_MONOTONIC_COARSE source of time that is less
accurate but more performant.
We have a BPF CGROUP_SKB firewall that supports event logging through
bpf_perf_event_output(). Each event has a timestamp and currently we use
bpf_ktime_get_ns() for it. Use of bpf_ktime_get_coarse_ns() saves ~15-20
ns in time required for event logging.
bpf_ktime_get_ns():
EgressLogByRemoteEndpoint 113.82ns 8.79M
bpf_ktime_get_coarse_ns():
EgressLogByRemoteEndpoint 95.40ns 10.48M
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201117184549.257280-1-me@ubique.spb.ru
The helper allows modification of certain bits on the linux_binprm
struct starting with the secureexec bit which can be updated using the
BPF_F_BPRM_SECUREEXEC flag.
secureexec can be set by the LSM for privilege gaining executions to set
the AT_SECURE auxv for glibc. When set, the dynamic linker disables the
use of certain environment variables (like LD_PRELOAD).
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201117232929.2156341-1-kpsingh@chromium.org
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-11-14
1) Add BTF generation for kernel modules and extend BTF infra in kernel
e.g. support for split BTF loading and validation, from Andrii Nakryiko.
2) Support for pointers beyond pkt_end to recognize LLVM generated patterns
on inlined branch conditions, from Alexei Starovoitov.
3) Implements bpf_local_storage for task_struct for BPF LSM, from KP Singh.
4) Enable FENTRY/FEXIT/RAW_TP tracing program to use the bpf_sk_storage
infra, from Martin KaFai Lau.
5) Add XDP bulk APIs that introduce a defer/flush mechanism to optimize the
XDP_REDIRECT path, from Lorenzo Bianconi.
6) Fix a potential (although rather theoretical) deadlock of hashtab in NMI
context, from Song Liu.
7) Fixes for cross and out-of-tree build of bpftool and runqslower allowing build
for different target archs on same source tree, from Jean-Philippe Brucker.
8) Fix error path in htab_map_alloc() triggered from syzbot, from Eric Dumazet.
9) Move functionality from test_tcpbpf_user into the test_progs framework so it
can run in BPF CI, from Alexander Duyck.
10) Lift hashtab key_size limit to be larger than MAX_BPF_STACK, from Florian Lehner.
Note that for the fix from Song we have seen a sparse report on context
imbalance which requires changes in sparse itself for proper annotation
detection where this is currently being discussed on linux-sparse among
developers [0]. Once we have more clarification/guidance after their fix,
Song will follow-up.
[0] https://lore.kernel.org/linux-sparse/CAHk-=wh4bx8A8dHnX612MsDO13st6uzAz1mJ1PaHHVevJx_ZCw@mail.gmail.com/T/https://lore.kernel.org/linux-sparse/20201109221345.uklbp3lzgq6g42zb@ltop.local/T/
* git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (66 commits)
net: mlx5: Add xdp tx return bulking support
net: mvpp2: Add xdp tx return bulking support
net: mvneta: Add xdp tx return bulking support
net: page_pool: Add bulk support for ptr_ring
net: xdp: Introduce bulking for xdp tx return path
bpf: Expose bpf_d_path helper to sleepable LSM hooks
bpf: Augment the set of sleepable LSM hooks
bpf: selftest: Use bpf_sk_storage in FENTRY/FEXIT/RAW_TP
bpf: Allow using bpf_sk_storage in FENTRY/FEXIT/RAW_TP
bpf: Rename some functions in bpf_sk_storage
bpf: Folding omem_charge() into sk_storage_charge()
selftests/bpf: Add asm tests for pkt vs pkt_end comparison.
selftests/bpf: Add skb_pkt_end test
bpf: Support for pointers beyond pkt_end.
tools/bpf: Always run the *-clean recipes
tools/bpf: Add bootstrap/ to .gitignore
bpf: Fix NULL dereference in bpf_task_storage
tools/bpftool: Fix build slowdown
tools/runqslower: Build bpftool using HOSTCC
tools/runqslower: Enable out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20201114020819.29584-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently verifier enforces return code checks for subprograms in the
same manner as it does for program entry points. This prevents returning
arbitrary scalar values from subprograms. Scalar type of returned values
is checked by btf_prepare_func_args() and hence it should be safe to
allow only scalars for now. Relax return code checks for subprograms and
allow any correct scalar values.
Fixes: 51c39bb1d5 (bpf: Introduce function-by-function verification)
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201113171756.90594-1-me@ubique.spb.ru
Update the set of sleepable hooks with the ones that do not trigger
a warning with might_fault() when exercised with the correct kernel
config options enabled, i.e.
DEBUG_ATOMIC_SLEEP=y
LOCKDEP=y
PROVE_LOCKING=y
This means that a sleepable LSM eBPF program can be attached to these
LSM hooks. A new helper method bpf_lsm_is_sleepable_hook is added and
the set is maintained locally in bpf_lsm.c
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201113005930.541956-2-kpsingh@chromium.org
This patch adds the verifier support to recognize inlined branch conditions.
The LLVM knows that the branch evaluates to the same value, but the verifier
couldn't track it. Hence causing valid programs to be rejected.
The potential LLVM workaround: https://reviews.llvm.org/D87428
can have undesired side effects, since LLVM doesn't know that
skb->data/data_end are being compared. LLVM has to introduce extra boolean
variable and use inline_asm trick to force easier for the verifier assembly.
Instead teach the verifier to recognize that
r1 = skb->data;
r1 += 10;
r2 = skb->data_end;
if (r1 > r2) {
here r1 points beyond packet_end and
subsequent
if (r1 > r2) // always evaluates to "true".
}
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20201111031213.25109-2-alexei.starovoitov@gmail.com
In bpf_pid_task_storage_update_elem(), it missed to
test the !task_storage_ptr(task) which then could trigger a NULL
pointer exception in bpf_local_storage_update().
Fixes: 4cf1bc1f10 ("bpf: Implement task local storage")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Roman Gushchin <guro@fb.com>
Acked-by: KP Singh <kpsingh@google.com>
Link: https://lore.kernel.org/bpf/20201112001919.2028357-1-kafai@fb.com
The unsigned variable datasec_id is assigned a return value from the call
to check_pseudo_btf_id(), which may return negative error code.
This fixes the following coccicheck warning:
./kernel/bpf/verifier.c:9616:5-15: WARNING: Unsigned expression compared with zero: datasec_id > 0
Fixes: eaa6bcb71e ("bpf: Introduce bpf_per_cpu_ptr()")
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Cc: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/bpf/1605071026-25906-1-git-send-email-kaixuxia@tencent.com
Make sure btf_parse_module() is compiled out if module BTFs are not enabled.
Fixes: 36e68442d1 ("bpf: Load and verify kernel module BTFs")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201111040645.903494-1-andrii@kernel.org
Add kernel module listener that will load/validate and unload module BTF.
Module BTFs gets ID generated for them, which makes it possible to iterate
them with existing BTF iteration API. They are given their respective module's
names, which will get reported through GET_OBJ_INFO API. They are also marked
as in-kernel BTFs for tooling to distinguish them from user-provided BTFs.
Also, similarly to vmlinux BTF, kernel module BTFs are exposed through
sysfs as /sys/kernel/btf/<module-name>. This is convenient for user-space
tools to inspect module BTF contents and dump their types with existing tools:
[vmuser@archvm bpf]$ ls -la /sys/kernel/btf
total 0
drwxr-xr-x 2 root root 0 Nov 4 19:46 .
drwxr-xr-x 13 root root 0 Nov 4 19:46 ..
...
-r--r--r-- 1 root root 888 Nov 4 19:46 irqbypass
-r--r--r-- 1 root root 100225 Nov 4 19:46 kvm
-r--r--r-- 1 root root 35401 Nov 4 19:46 kvm_intel
-r--r--r-- 1 root root 120 Nov 4 19:46 pcspkr
-r--r--r-- 1 root root 399 Nov 4 19:46 serio_raw
-r--r--r-- 1 root root 4094095 Nov 4 19:46 vmlinux
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/bpf/20201110011932.3201430-5-andrii@kernel.org
Allocate ID for vmlinux BTF. This makes it visible when iterating over all BTF
objects in the system. To allow distinguishing vmlinux BTF (and later kernel
module BTF) from user-provided BTFs, expose extra kernel_btf flag, as well as
BTF name ("vmlinux" for vmlinux BTF, will equal to module's name for module
BTF). We might want to later allow specifying BTF name for user-provided BTFs
as well, if that makes sense. But currently this is reserved only for
in-kernel BTFs.
Having in-kernel BTFs exposed IDs will allow to extend BPF APIs that require
in-kernel BTF type with ability to specify BTF types from kernel modules, not
just vmlinux BTF. This will be implemented in a follow up patch set for
fentry/fexit/fmod_ret/lsm/etc.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201110011932.3201430-3-andrii@kernel.org
Adjust in-kernel BTF implementation to support a split BTF mode of operation.
Changes are mostly mirroring libbpf split BTF changes, with the exception of
start_id being 0 for in-kernel implementation due to simpler read-only mode.
Otherwise, for split BTF logic, most of the logic of jumping to base BTF,
where necessary, is encapsulated in few helper functions. Type numbering and
string offset in a split BTF are logically continuing where base BTF ends, so
most of the high-level logic is kept without changes.
Type verification and size resolution is only doing an added resolution of new
split BTF types and relies on already cached size and type resolution results
in the base BTF.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201110011932.3201430-2-andrii@kernel.org
The current logic checks if the name of the BTF type passed in
attach_btf_id starts with "bpf_lsm_", this is not sufficient as it also
allows attachment to non-LSM hooks like the very function that performs
this check, i.e. bpf_lsm_verify_prog.
In order to ensure that this verification logic allows attachment to
only LSM hooks, the LSM_HOOK definitions in lsm_hook_defs.h are used to
generate a BTF_ID set. Upon verification, the attach_btf_id of the
program being attached is checked for presence in this set.
Fixes: 9e4e01dfd3 ("bpf: lsm: Implement attach, detach and execution")
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201105230651.2621917-1-kpsingh@chromium.org
The currently available bpf_get_current_task returns an unsigned integer
which can be used along with BPF_CORE_READ to read data from
the task_struct but still cannot be used as an input argument to a
helper that accepts an ARG_PTR_TO_BTF_ID of type task_struct.
In order to implement this helper a new return type, RET_PTR_TO_BTF_ID,
is added. This is similar to RET_PTR_TO_BTF_ID_OR_NULL but does not
require checking the nullness of returned pointer.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201106103747.2780972-6-kpsingh@chromium.org
Similar to bpf_local_storage for sockets and inodes add local storage
for task_struct.
The life-cycle of storage is managed with the life-cycle of the
task_struct. i.e. the storage is destroyed along with the owning task
with a callback to the bpf_task_storage_free from the task_free LSM
hook.
The BPF LSM allocates an __rcu pointer to the bpf_local_storage in
the security blob which are now stackable and can co-exist with other
LSMs.
The userspace map operations can be done by using a pid fd as a key
passed to the lookup, update and delete operations.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201106103747.2780972-3-kpsingh@chromium.org
Usage of spin locks was not allowed for tracing programs due to
insufficient preemption checks. The verifier does not currently prevent
LSM programs from using spin locks, but the helpers are not exposed
via bpf_lsm_func_proto.
Based on the discussion in [1], non-sleepable LSM programs should be
able to use bpf_spin_{lock, unlock}.
Sleepable LSM programs can be preempted which means that allowng spin
locks will need more work (disabling preemption and the verifier
ensuring that no sleepable helpers are called when a spin lock is held).
[1]: https://lore.kernel.org/bpf/20201103153132.2717326-1-kpsingh@chromium.org/T/#md601a053229287659071600d3483523f752cd2fb
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201106103747.2780972-2-kpsingh@chromium.org
Currently key_size of hashtab is limited to MAX_BPF_STACK.
As the key of hashtab can also be a value from a per cpu map it can be
larger than MAX_BPF_STACK.
The use-case for this patch originates to implement allow/disallow
lists for files and file paths. The maximum length of file paths is
defined by PATH_MAX with 4096 chars including nul.
This limit exceeds MAX_BPF_STACK.
Changelog:
v5:
- Fix cast overflow
v4:
- Utilize BPF skeleton in tests
- Rebase
v3:
- Rebase
v2:
- Add a test for bpf side
Signed-off-by: Florian Lehner <dev@der-flo.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201029201442.596690-1-dev@der-flo.net
Zero-fill element values for all other cpus than current, just as
when not using prealloc. This is the only way the bpf program can
ensure known initial values for all cpus ('onallcpus' cannot be
set when coming from the bpf program).
The scenario is: bpf program inserts some elements in a per-cpu
map, then deletes some (or userspace does). When later adding
new elements using bpf_map_update_elem(), the bpf program can
only set the value of the new elements for the current cpu.
When prealloc is enabled, previously deleted elements are re-used.
Without the fix, values for other cpus remain whatever they were
when the re-used entry was previously freed.
A selftest is added to validate correct operation in above
scenario as well as in case of LRU per-cpu map element re-use.
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Signed-off-by: David Verbeiren <david.verbeiren@tessares.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201104112332.15191-1-david.verbeiren@tessares.net
Fix build error when BPF_SYSCALL is not set/enabled but BPF_PRELOAD is
by making BPF_PRELOAD depend on BPF_SYSCALL.
ERROR: modpost: "bpf_preload_ops" [kernel/bpf/preload/bpf_preload.ko] undefined!
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201105195109.26232-1-rdunlap@infradead.org
If a hashtab is accessed in both non-NMI and NMI context, the system may
deadlock on bucket->lock. Fix this issue with percpu counter map_locked.
map_locked rejects concurrent access to the same bucket from the same CPU.
To reduce memory overhead, map_locked is not added per bucket. Instead,
8 percpu counters are added to each hashtab. buckets are assigned to these
counters based on the lower bits of its hash.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201029071925.3103400-3-songliubraving@fb.com
Commit 3193c0836 ("bpf: Disable GCC -fgcse optimization for
___bpf_prog_run()") introduced a __no_fgcse macro that expands to a
function scope __attribute__((optimize("-fno-gcse"))), to disable a
GCC specific optimization that was causing trouble on x86 builds, and
was not expected to have any positive effect in the first place.
However, as the GCC manual documents, __attribute__((optimize))
is not for production use, and results in all other optimization
options to be forgotten for the function in question. This can
cause all kinds of trouble, but in one particular reported case,
it causes -fno-asynchronous-unwind-tables to be disregarded,
resulting in .eh_frame info to be emitted for the function.
This reverts commit 3193c0836, and instead, it disables the -fgcse
optimization for the entire source file, but only when building for
X86 using GCC with CONFIG_BPF_JIT_ALWAYS_ON disabled. Note that the
original commit states that CONFIG_RETPOLINE=n triggers the issue,
whereas CONFIG_RETPOLINE=y performs better without the optimization,
so it is kept disabled in both cases.
Fixes: 3193c0836f ("bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/lkml/CAMuHMdUg0WJHEcq6to0-eODpXPOywLot6UD2=GFHpzoj_hCoBQ@mail.gmail.com/
Link: https://lore.kernel.org/bpf/20201028171506.15682-2-ardb@kernel.org
Commit e679654a70 ("bpf: Fix a rcu_sched stall issue with
bpf task/task_file iterator") tries to fix rcu stalls warning
which is caused by bpf task_file iterator when running
"bpftool prog".
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: \x097-....: (20999 ticks this GP) idle=302/1/0x4000000000000000 softirq=1508852/1508852 fqs=4913
\x09(t=21031 jiffies g=2534773 q=179750)
NMI backtrace for cpu 7
CPU: 7 PID: 184195 Comm: bpftool Kdump: loaded Tainted: G W 5.8.0-00004-g68bfc7f8c1b4 #6
Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A17 05/03/2019
Call Trace:
<IRQ>
dump_stack+0x57/0x70
nmi_cpu_backtrace.cold+0x14/0x53
? lapic_can_unplug_cpu.cold+0x39/0x39
nmi_trigger_cpumask_backtrace+0xb7/0xc7
rcu_dump_cpu_stacks+0xa2/0xd0
rcu_sched_clock_irq.cold+0x1ff/0x3d9
? tick_nohz_handler+0x100/0x100
update_process_times+0x5b/0x90
tick_sched_timer+0x5e/0xf0
__hrtimer_run_queues+0x12a/0x2a0
hrtimer_interrupt+0x10e/0x280
__sysvec_apic_timer_interrupt+0x51/0xe0
asm_call_on_stack+0xf/0x20
</IRQ>
sysvec_apic_timer_interrupt+0x6f/0x80
...
task_file_seq_next+0x52/0xa0
bpf_seq_read+0xb9/0x320
vfs_read+0x9d/0x180
ksys_read+0x5f/0xe0
do_syscall_64+0x38/0x60
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The fix is to limit the number of bpf program runs to be
one million. This fixed the program in most cases. But
we also found under heavy load, which can increase the wallclock
time for bpf_seq_read(), the warning may still be possible.
For example, calling bpf_delay() in the "while" loop of
bpf_seq_read(), which will introduce artificial delay,
the warning will show up in my qemu run.
static unsigned q;
volatile unsigned *p = &q;
volatile unsigned long long ll;
static void bpf_delay(void)
{
int i, j;
for (i = 0; i < 10000; i++)
for (j = 0; j < 10000; j++)
ll += *p;
}
There are two ways to fix this issue. One is to reduce the above
one million threshold to say 100,000 and hopefully rcu warning will
not show up any more. Another is to introduce a target feature
which enables bpf_seq_read() calling cond_resched().
This patch took second approach as the first approach may cause
more -EAGAIN failures for read() syscalls. Note that not all bpf_iter
targets can permit cond_resched() in bpf_seq_read() as some, e.g.,
netlink seq iterator, rcu read lock critical section spans through
seq_ops->next() -> seq_ops->show() -> seq_ops->next().
For the kernel code with the above hack, "bpftool p" roughly takes
38 seconds to finish on my VM with 184 bpf program runs.
Using the following command, I am able to collect the number of
context switches:
perf stat -e context-switches -- ./bpftool p >& log
Without this patch,
69 context-switches
With this patch,
75 context-switches
This patch added additional 6 context switches, roughly every 6 seconds
to reschedule, to avoid lengthy no-rescheduling which may cause the
above RCU warnings.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201028061054.1411116-1-yhs@fb.com
Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late
in the 5.9 cycle started depending on a return code from
a function which changed with the 5.10 PR from the usb subsystem
Current release - regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous releases - regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu()
to synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems;
the property is not populated correctly by the firmware,
but firmware configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is
light and only wants to schedule napi (and do so through
a _irqoff() variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ceke
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
Pull initial set_fs() removal from Al Viro:
"Christoph's set_fs base series + fixups"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Allow a NULL pos pointer to __kernel_read
fs: Allow a NULL pos pointer to __kernel_write
powerpc: remove address space overrides using set_fs()
powerpc: use non-set_fs based maccess routines
x86: remove address space overrides using set_fs()
x86: make TASK_SIZE_MAX usable from assembly code
x86: move PAGE_OFFSET, TASK_SIZE & friends to page_{32,64}_types.h
lkdtm: remove set_fs-based tests
test_bitmap: remove user bitmap tests
uaccess: add infrastructure for kernel builds with set_fs()
fs: don't allow splice read/write without explicit ops
fs: don't allow kernel reads and writes without iter ops
sysctl: Convert to iter interfaces
proc: add a read_iter method to proc proc_ops
proc: cleanup the compat vs no compat file ops
proc: remove a level of indentation in proc_get_inode
The commit af7ec13833 ("bpf: Add bpf_skc_to_tcp6_sock() helper")
introduces RET_PTR_TO_BTF_ID_OR_NULL and
the commit eaa6bcb71e ("bpf: Introduce bpf_per_cpu_ptr()")
introduces RET_PTR_TO_MEM_OR_BTF_ID_OR_NULL.
Note that for RET_PTR_TO_MEM_OR_BTF_ID_OR_NULL, the reg0->type
could become PTR_TO_MEM_OR_NULL which is not covered by
BPF_PROBE_MEM.
The BPF_REG_0 will then hold a _OR_NULL pointer type. This _OR_NULL
pointer type requires the bpf program to explicitly do a NULL check first.
After NULL check, the verifier will mark all registers having
the same reg->id as safe to use. However, the reg->id
is not set for those new _OR_NULL return types. One of the ways
that may be wrong is, checking NULL for one btf_id typed pointer will
end up validating all other btf_id typed pointers because
all of them have id == 0. The later tests will exercise
this path.
To fix it and also avoid similar issue in the future, this patch
moves the id generation logic out of each individual RET type
test in check_helper_call(). Instead, it does one
reg_type_may_be_null() test and then do the id generation
if needed.
This patch also adds a WARN_ON_ONCE in mark_ptr_or_null_reg()
to catch future breakage.
The _OR_NULL pointer usage in the bpf_iter_reg.ctx_arg_info is
fine because it just happens that the existing id generation after
check_ctx_access() has covered it. It is also using the
reg_type_may_be_null() to decide if id generation is needed or not.
Fixes: af7ec13833 ("bpf: Add bpf_skc_to_tcp6_sock() helper")
Fixes: eaa6bcb71e ("bpf: Introduce bpf_per_cpu_ptr()")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201019194212.1050855-1-kafai@fb.com
A break is not needed if it is preceded by a return.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201019173846.1021-1-trix@redhat.com
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
The 64-bit JEQ/JNE handling in reg_set_min_max() was clearing reg->id in either
true or false branch. In the case 'if (reg->id)' check was done on the other
branch the counter part register would have reg->id == 0 when called into
find_equal_scalars(). In such case the helper would incorrectly identify other
registers with id == 0 as equivalent and propagate the state incorrectly.
Fix it by preserving ID across reg_set_min_max().
In other words any kind of comparison operator on the scalar register
should preserve its ID to recognize:
r1 = r2
if (r1 == 20) {
#1 here both r1 and r2 == 20
} else if (r2 < 20) {
#2 here both r1 and r2 < 20
}
The patch is addressing #1 case. The #2 was working correctly already.
Fixes: 75748837b7 ("bpf: Propagate scalar ranges through register assignments.")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201014175608.1416-1-alexei.starovoitov@gmail.com
- Most of the changes are cleanups and reorganization to make the objtool code
more arch-agnostic. This is in preparation for non-x86 support.
Fixes:
- KASAN fixes.
- Handle unreachable trap after call to noreturn functions better.
- Ignore unreachable fake jumps.
- Misc smaller fixes & cleanups.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KX5o
-----END PGP SIGNATURE-----
Merge tag 'objtool-core-2020-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
"Most of the changes are cleanups and reorganization to make the
objtool code more arch-agnostic. This is in preparation for non-x86
support.
Other changes:
- KASAN fixes
- Handle unreachable trap after call to noreturn functions better
- Ignore unreachable fake jumps
- Misc smaller fixes & cleanups"
* tag 'objtool-core-2020-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf build: Allow nested externs to enable BUILD_BUG() usage
objtool: Allow nested externs to enable BUILD_BUG()
objtool: Permit __kasan_check_{read,write} under UACCESS
objtool: Ignore unreachable trap after call to noreturn functions
objtool: Handle calling non-function symbols in other sections
objtool: Ignore unreachable fake jumps
objtool: Remove useless tests before save_reg()
objtool: Decode unwind hint register depending on architecture
objtool: Make unwind hint definitions available to other architectures
objtool: Only include valid definitions depending on source file type
objtool: Rename frame.h -> objtool.h
objtool: Refactor jump table code to support other architectures
objtool: Make relocation in alternative handling arch dependent
objtool: Abstract alternative special case handling
objtool: Move macros describing structures to arch-dependent code
objtool: Make sync-check consider the target architecture
objtool: Group headers to check in a single list
objtool: Define 'struct orc_entry' only when needed
objtool: Skip ORC entry creation for non-text sections
objtool: Move ORC logic out of check()
...
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-10-12
The main changes are:
1) The BPF verifier improvements to track register allocation pattern, from Alexei and Yonghong.
2) libbpf relocation support for different size load/store, from Andrii.
3) bpf_redirect_peer() helper and support for inner map array with different max_entries, from Daniel.
4) BPF support for per-cpu variables, form Hao.
5) sockmap improvements, from John.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent work in f4d0525921 ("bpf: Add map_meta_equal map ops") and 134fede4ee
("bpf: Relax max_entries check for most of the inner map types") added support
for dynamic inner max elements for most map-in-map types. Exceptions were maps
like array or prog array where the map_gen_lookup() callback uses the maps'
max_entries field as a constant when emitting instructions.
We recently implemented Maglev consistent hashing into Cilium's load balancer
which uses map-in-map with an outer map being hash and inner being array holding
the Maglev backend table for each service. This has been designed this way in
order to reduce overall memory consumption given the outer hash map allows to
avoid preallocating a large, flat memory area for all services. Also, the
number of service mappings is not always known a-priori.
The use case for dynamic inner array map entries is to further reduce memory
overhead, for example, some services might just have a small number of back
ends while others could have a large number. Right now the Maglev backend table
for small and large number of backends would need to have the same inner array
map entries which adds a lot of unneeded overhead.
Dynamic inner array map entries can be realized by avoiding the inlined code
generation for their lookup. The lookup will still be efficient since it will
be calling into array_map_lookup_elem() directly and thus avoiding retpoline.
The patch adds a BPF_F_INNER_MAP flag to map creation which therefore skips
inline code generation and relaxes array_map_meta_equal() check to ignore both
maps' max_entries. This also still allows to have faster lookups for map-in-map
when BPF_F_INNER_MAP is not specified and hence dynamic max_entries not needed.
Example code generation where inner map is dynamic sized array:
# bpftool p d x i 125
int handle__sys_enter(void * ctx):
; int handle__sys_enter(void *ctx)
0: (b4) w1 = 0
; int key = 0;
1: (63) *(u32 *)(r10 -4) = r1
2: (bf) r2 = r10
;
3: (07) r2 += -4
; inner_map = bpf_map_lookup_elem(&outer_arr_dyn, &key);
4: (18) r1 = map[id:468]
6: (07) r1 += 272
7: (61) r0 = *(u32 *)(r2 +0)
8: (35) if r0 >= 0x3 goto pc+5
9: (67) r0 <<= 3
10: (0f) r0 += r1
11: (79) r0 = *(u64 *)(r0 +0)
12: (15) if r0 == 0x0 goto pc+1
13: (05) goto pc+1
14: (b7) r0 = 0
15: (b4) w6 = -1
; if (!inner_map)
16: (15) if r0 == 0x0 goto pc+6
17: (bf) r2 = r10
;
18: (07) r2 += -4
; val = bpf_map_lookup_elem(inner_map, &key);
19: (bf) r1 = r0 | No inlining but instead
20: (85) call array_map_lookup_elem#149280 | call to array_map_lookup_elem()
; return val ? *val : -1; | for inner array lookup.
21: (15) if r0 == 0x0 goto pc+1
; return val ? *val : -1;
22: (61) r6 = *(u32 *)(r0 +0)
; }
23: (bc) w0 = w6
24: (95) exit
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201010234006.7075-4-daniel@iogearbox.net
Under register pressure the llvm may spill registers with bounds into the stack.
The verifier has to track them through spill/fill otherwise many kinds of bound
errors will be seen. The spill/fill of induction variables was already
happening. This patch extends this logic from tracking spill/fill of a constant
into any bounded register. There is no need to track spill/fill of unbounded,
since no new information will be retrieved from the stack during register fill.
Though extra stack difference could cause state pruning to be less effective, no
adverse affects were seen from this patch on selftests and on cilium programs.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20201009011240.48506-3-alexei.starovoitov@gmail.com
The llvm register allocator may use two different registers representing the
same virtual register. In such case the following pattern can be observed:
1047: (bf) r9 = r6
1048: (a5) if r6 < 0x1000 goto pc+1
1050: ...
1051: (a5) if r9 < 0x2 goto pc+66
1052: ...
1053: (bf) r2 = r9 /* r2 needs to have upper and lower bounds */
This is normal behavior of greedy register allocator.
The slides 137+ explain why regalloc introduces such register copy:
http://llvm.org/devmtg/2018-04/slides/Yatsina-LLVM%20Greedy%20Register%20Allocator.pdf
There is no way to tell llvm 'not to do this'.
Hence the verifier has to recognize such patterns.
In order to track this information without backtracking allocate ID
for scalars in a similar way as it's done for find_good_pkt_pointers().
When the verifier encounters r9 = r6 assignment it will assign the same ID
to both registers. Later if either register range is narrowed via conditional
jump propagate the register state into the other register.
Clear register ID in adjust_reg_min_max_vals() for any alu instruction. The
register ID is ignored for scalars in regsafe() and doesn't affect state
pruning. mark_reg_unknown() clears the ID. It's used to process call, endian
and other instructions. Hence ID is explicitly cleared only in
adjust_reg_min_max_vals() and in 32-bit mov.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20201009011240.48506-2-alexei.starovoitov@gmail.com
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported an issue with the current scalar32_min_max_or() implementation.
That is, compared to the other 32 bit subreg tracking functions, the code in
scalar32_min_max_or() stands out that it's using the 64 bit registers instead
of 32 bit ones. This leads to bounds tracking issues, for example:
[...]
8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
8: (79) r1 = *(u64 *)(r0 +0)
R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
9: (b7) r0 = 1
10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
10: (18) r2 = 0x600000002
12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
12: (ad) if r1 < r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: (95) exit
14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
14: (25) if r1 > 0x0 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: (95) exit
16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
16: (47) r1 |= 0
17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x1; 0x700000000),s32_max_value=1,u32_max_value=1) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
[...]
The bound tests on the map value force the upper unsigned bound to be 25769803777
in 64 bit (0b11000000000000000000000000000000001) and then lower one to be 1. By
using OR they are truncated and thus result in the range [1,1] for the 32 bit reg
tracker. This is incorrect given the only thing we know is that the value must be
positive and thus 2147483647 (0b1111111111111111111111111111111) at max for the
subregs. Fix it by using the {u,s}32_{min,max}_value vars instead. This also makes
sense, for example, for the case where we update dst_reg->s32_{min,max}_value in
the else branch we need to use the newly computed dst_reg->u32_{min,max}_value as
we know that these are positive. Previously, in the else branch the 64 bit values
of umin_value=1 and umax_value=32212254719 were used and latter got truncated to
be 1 as upper bound there. After the fix the subreg range is now correct:
[...]
8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
8: (79) r1 = *(u64 *)(r0 +0)
R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
9: (b7) r0 = 1
10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
10: (18) r2 = 0x600000002
12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
12: (ad) if r1 < r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: (95) exit
14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
14: (25) if r1 > 0x0 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: (95) exit
16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
16: (47) r1 |= 0
17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
[...]
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Simon Scannell <scannell.smn@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Fix build errors in kernel/bpf/verifier.c when CONFIG_NET is
not enabled.
../kernel/bpf/verifier.c:3995:13: error: ‘btf_sock_ids’ undeclared here (not in a function); did you mean ‘bpf_sock_ops’?
.btf_id = &btf_sock_ids[BTF_SOCK_TYPE_SOCK_COMMON],
../kernel/bpf/verifier.c:3995:26: error: ‘BTF_SOCK_TYPE_SOCK_COMMON’ undeclared here (not in a function); did you mean ‘PTR_TO_SOCK_COMMON’?
.btf_id = &btf_sock_ids[BTF_SOCK_TYPE_SOCK_COMMON],
Fixes: 1df8f55a37 ("bpf: Enable bpf_skc_to_* sock casting helper to networking prog type")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201007021613.13646-1-rdunlap@infradead.org
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent improvements in LOCKDEP highlighted a potential A-A deadlock with
pcpu_freelist in NMI:
./tools/testing/selftests/bpf/test_progs -t stacktrace_build_id_nmi
[ 18.984807] ================================
[ 18.984807] WARNING: inconsistent lock state
[ 18.984808] 5.9.0-rc6-01771-g1466de1330e1 #2967 Not tainted
[ 18.984809] --------------------------------
[ 18.984809] inconsistent {INITIAL USE} -> {IN-NMI} usage.
[ 18.984810] test_progs/1990 [HC2[2]:SC0[0]:HE0:SE1] takes:
[ 18.984810] ffffe8ffffc219c0 (&head->lock){....}-{2:2}, at: __pcpu_freelist_pop+0xe3/0x180
[ 18.984813] {INITIAL USE} state was registered at:
[ 18.984814] lock_acquire+0x175/0x7c0
[ 18.984814] _raw_spin_lock+0x2c/0x40
[ 18.984815] __pcpu_freelist_pop+0xe3/0x180
[ 18.984815] pcpu_freelist_pop+0x31/0x40
[ 18.984816] htab_map_alloc+0xbbf/0xf40
[ 18.984816] __do_sys_bpf+0x5aa/0x3ed0
[ 18.984817] do_syscall_64+0x2d/0x40
[ 18.984818] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 18.984818] irq event stamp: 12
[...]
[ 18.984822] other info that might help us debug this:
[ 18.984823] Possible unsafe locking scenario:
[ 18.984823]
[ 18.984824] CPU0
[ 18.984824] ----
[ 18.984824] lock(&head->lock);
[ 18.984826] <Interrupt>
[ 18.984826] lock(&head->lock);
[ 18.984827]
[ 18.984828] *** DEADLOCK ***
[ 18.984828]
[ 18.984829] 2 locks held by test_progs/1990:
[...]
[ 18.984838] <NMI>
[ 18.984838] dump_stack+0x9a/0xd0
[ 18.984839] lock_acquire+0x5c9/0x7c0
[ 18.984839] ? lock_release+0x6f0/0x6f0
[ 18.984840] ? __pcpu_freelist_pop+0xe3/0x180
[ 18.984840] _raw_spin_lock+0x2c/0x40
[ 18.984841] ? __pcpu_freelist_pop+0xe3/0x180
[ 18.984841] __pcpu_freelist_pop+0xe3/0x180
[ 18.984842] pcpu_freelist_pop+0x17/0x40
[ 18.984842] ? lock_release+0x6f0/0x6f0
[ 18.984843] __bpf_get_stackid+0x534/0xaf0
[ 18.984843] bpf_prog_1fd9e30e1438d3c5_oncpu+0x73/0x350
[ 18.984844] bpf_overflow_handler+0x12f/0x3f0
This is because pcpu_freelist_head.lock is accessed in both NMI and
non-NMI context. Fix this issue by using raw_spin_trylock() in NMI.
Since NMI interrupts non-NMI context, when NMI context tries to lock the
raw_spinlock, non-NMI context of the same CPU may already have locked a
lock and is blocked from unlocking the lock. For a system with N CPUs,
there could be N NMIs at the same time, and they may block N non-NMI
raw_spinlocks. This is tricky for pcpu_freelist_push(), where unlike
_pop(), failing _push() means leaking memory. This issue is more likely to
trigger in non-SMP system.
Fix this issue with an extra list, pcpu_freelist.extralist. The extralist
is primarily used to take _push() when raw_spin_trylock() failed on all
the per CPU lists. It should be empty most of the time. The following
table summarizes the behavior of pcpu_freelist in NMI and non-NMI:
non-NMI pop(): use _lock(); check per CPU lists first;
if all per CPU lists are empty, check extralist;
if extralist is empty, return NULL.
non-NMI push(): use _lock(); only push to per CPU lists.
NMI pop(): use _trylock(); check per CPU lists first;
if all per CPU lists are locked or empty, check extralist;
if extralist is locked or empty, return NULL.
NMI push(): use _trylock(); check per CPU lists first;
if all per CPU lists are locked; try push to extralist;
if extralist is also locked, keep trying on per CPU lists.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201005165838.3735218-1-songliubraving@fb.com
We are missing a deref for the case when we are doing BPF_PROG_BIND_MAP
on a map that's being already held by the program.
There is 'if (ret) bpf_map_put(map)' below which doesn't trigger
because we don't consider this an error.
Let's add missing bpf_map_put() for this specific condition.
Fixes: ef15314aa5 ("bpf: Add BPF_PROG_BIND_MAP syscall")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20201003002544.3601440-1-sdf@google.com
Add bpf_this_cpu_ptr() to help access percpu var on this cpu. This
helper always returns a valid pointer, therefore no need to check
returned value for NULL. Also note that all programs run with
preemption disabled, which means that the returned pointer is stable
during all the execution of the program.
Signed-off-by: Hao Luo <haoluo@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200929235049.2533242-6-haoluo@google.com
Add bpf_per_cpu_ptr() to help bpf programs access percpu vars.
bpf_per_cpu_ptr() has the same semantic as per_cpu_ptr() in the kernel
except that it may return NULL. This happens when the cpu parameter is
out of range. So the caller must check the returned value.
Signed-off-by: Hao Luo <haoluo@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200929235049.2533242-5-haoluo@google.com
Pseudo_btf_id is a type of ld_imm insn that associates a btf_id to a
ksym so that further dereferences on the ksym can use the BTF info
to validate accesses. Internally, when seeing a pseudo_btf_id ld insn,
the verifier reads the btf_id stored in the insn[0]'s imm field and
marks the dst_reg as PTR_TO_BTF_ID. The btf_id points to a VAR_KIND,
which is encoded in btf_vminux by pahole. If the VAR is not of a struct
type, the dst reg will be marked as PTR_TO_MEM instead of PTR_TO_BTF_ID
and the mem_size is resolved to the size of the VAR's type.
>From the VAR btf_id, the verifier can also read the address of the
ksym's corresponding kernel var from kallsyms and use that to fill
dst_reg.
Therefore, the proper functionality of pseudo_btf_id depends on (1)
kallsyms and (2) the encoding of kernel global VARs in pahole, which
should be available since pahole v1.18.
Signed-off-by: Hao Luo <haoluo@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200929235049.2533242-2-haoluo@google.com
Currently, perf event in perf event array is removed from the array when
the map fd used to add the event is closed. This behavior makes it
difficult to the share perf events with perf event array.
Introduce perf event map that keeps the perf event open with a new flag
BPF_F_PRESERVE_ELEMS. With this flag set, perf events in the array are not
removed when the original map fd is closed. Instead, the perf event will
stay in the map until 1) it is explicitly removed from the array; or 2)
the array is freed.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200930224927.1936644-2-songliubraving@fb.com
With its use in BPF, the cookie generator can be called very frequently
in particular when used out of cgroup v2 hooks (e.g. connect / sendmsg)
and attached to the root cgroup, for example, when used in v1/v2 mixed
environments. In particular, when there's a high churn on sockets in the
system there can be many parallel requests to the bpf_get_socket_cookie()
and bpf_get_netns_cookie() helpers which then cause contention on the
atomic counter.
As similarly done in f991bd2e14 ("fs: introduce a per-cpu last_ino
allocator"), add a small helper library that both can use for the 64 bit
counters. Given this can be called from different contexts, we also need
to deal with potential nested calls even though in practice they are
considered extremely rare. One idea as suggested by Eric Dumazet was
to use a reverse counter for this situation since we don't expect 64 bit
overflows anyways; that way, we can avoid bigger gaps in the 64 bit
counter space compared to just batch-wise increase. Even on machines
with small number of cores (e.g. 4) the cookie generation shrinks from
min/max/med/avg (ns) of 22/50/40/38.9 down to 10/35/14/17.3 when run
in parallel from multiple CPUs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Link: https://lore.kernel.org/bpf/8a80b8d27d3c49f9a14e1d5213c19d8be87d1dc8.1601477936.git.daniel@iogearbox.net
Eelco reported we can't properly access arguments if the tracing
program is attached to extension program.
Having following program:
SEC("classifier/test_pkt_md_access")
int test_pkt_md_access(struct __sk_buff *skb)
with its extension:
SEC("freplace/test_pkt_md_access")
int test_pkt_md_access_new(struct __sk_buff *skb)
and tracing that extension with:
SEC("fentry/test_pkt_md_access_new")
int BPF_PROG(fentry, struct sk_buff *skb)
It's not possible to access skb argument in the fentry program,
with following error from verifier:
; int BPF_PROG(fentry, struct sk_buff *skb)
0: (79) r1 = *(u64 *)(r1 +0)
invalid bpf_context access off=0 size=8
The problem is that btf_ctx_access gets the context type for the
traced program, which is in this case the extension.
But when we trace extension program, we want to get the context
type of the program that the extension is attached to, so we can
access the argument properly in the trace program.
This version of the patch is tweaked slightly from Jiri's original one,
since the refactoring in the previous patches means we have to get the
target prog type from the new variable in prog->aux instead of directly
from the target prog.
Reported-by: Eelco Chaudron <echaudro@redhat.com>
Suggested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/160138355278.48470.17057040257274725638.stgit@toke.dk
This enables support for attaching freplace programs to multiple attach
points. It does this by amending the UAPI for bpf_link_Create with a target
btf ID that can be used to supply the new attachment point along with the
target program fd. The target must be compatible with the target that was
supplied at program load time.
The implementation reuses the checks that were factored out of
check_attach_btf_id() to ensure compatibility between the BTF types of the
old and new attachment. If these match, a new bpf_tracing_link will be
created for the new attach target, allowing multiple attachments to
co-exist simultaneously.
The code could theoretically support multiple-attach of other types of
tracing programs as well, but since I don't have a use case for any of
those, there is no API support for doing so.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/160138355169.48470.17165680973640685368.stgit@toke.dk
In preparation for allowing multiple attachments of freplace programs, move
the references to the target program and trampoline into the
bpf_tracing_link structure when that is created. To do this atomically,
introduce a new mutex in prog->aux to protect writing to the two pointers
to target prog and trampoline, and rename the members to make it clear that
they are related.
With this change, it is no longer possible to attach the same tracing
program multiple times (detaching in-between), since the reference from the
tracing program to the target disappears on the first attach. However,
since the next patch will let the caller supply an attach target, that will
also make it possible to attach to the same place multiple times.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/160138355059.48470.2503076992210324984.stgit@toke.dk
The Makefile in bpf/preload builds a local copy of libbpf, but does not
properly clean up after itself. This can lead to subsequent compilation
failures, since the feature detection cache is kept around which can lead
subsequent detection to fail.
Fix this by properly setting clean-files, and while we're at it, also add a
.gitignore for the directory to ignore the build artifacts.
Fixes: d71fa5c976 ("bpf: Add kernel module with user mode driver that populates bpffs.")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200927193005.8459-1-toke@redhat.com
A helper is added to allow seq file writing of kernel data
structures using vmlinux BTF. Its signature is
long bpf_seq_printf_btf(struct seq_file *m, struct btf_ptr *ptr,
u32 btf_ptr_size, u64 flags);
Flags and struct btf_ptr definitions/use are identical to the
bpf_snprintf_btf helper, and the helper returns 0 on success
or a negative error value.
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1601292670-1616-8-git-send-email-alan.maguire@oracle.com
BPF iter size is limited to PAGE_SIZE; if we wish to display BTF-based
representations of larger kernel data structures such as task_struct,
this will be insufficient.
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1601292670-1616-6-git-send-email-alan.maguire@oracle.com
A helper is added to support tracing kernel type information in BPF
using the BPF Type Format (BTF). Its signature is
long bpf_snprintf_btf(char *str, u32 str_size, struct btf_ptr *ptr,
u32 btf_ptr_size, u64 flags);
struct btf_ptr * specifies
- a pointer to the data to be traced
- the BTF id of the type of data pointed to
- a flags field is provided for future use; these flags
are not to be confused with the BTF_F_* flags
below that control how the btf_ptr is displayed; the
flags member of the struct btf_ptr may be used to
disambiguate types in kernel versus module BTF, etc;
the main distinction is the flags relate to the type
and information needed in identifying it; not how it
is displayed.
For example a BPF program with a struct sk_buff *skb
could do the following:
static struct btf_ptr b = { };
b.ptr = skb;
b.type_id = __builtin_btf_type_id(struct sk_buff, 1);
bpf_snprintf_btf(str, sizeof(str), &b, sizeof(b), 0, 0);
Default output looks like this:
(struct sk_buff){
.transport_header = (__u16)65535,
.mac_header = (__u16)65535,
.end = (sk_buff_data_t)192,
.head = (unsigned char *)0x000000007524fd8b,
.data = (unsigned char *)0x000000007524fd8b,
.truesize = (unsigned int)768,
.users = (refcount_t){
.refs = (atomic_t){
.counter = (int)1,
},
},
}
Flags modifying display are as follows:
- BTF_F_COMPACT: no formatting around type information
- BTF_F_NONAME: no struct/union member names/types
- BTF_F_PTR_RAW: show raw (unobfuscated) pointer values;
equivalent to %px.
- BTF_F_ZERO: show zero-valued struct/union members;
they are not displayed by default
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1601292670-1616-4-git-send-email-alan.maguire@oracle.com
generalize the "seq_show" seq file support in btf.c to support
a generic show callback of which we support two instances; the
current seq file show, and a show with snprintf() behaviour which
instead writes the type data to a supplied string.
Both classes of show function call btf_type_show() with different
targets; the seq file or the string to be written. In the string
case we need to track additional data - length left in string to write
and length to return that we would have written (a la snprintf).
By default show will display type information, field members and
their types and values etc, and the information is indented
based upon structure depth. Zeroed fields are omitted.
Show however supports flags which modify its behaviour:
BTF_SHOW_COMPACT - suppress newline/indent.
BTF_SHOW_NONAME - suppress show of type and member names.
BTF_SHOW_PTR_RAW - do not obfuscate pointer values.
BTF_SHOW_UNSAFE - do not copy data to safe buffer before display.
BTF_SHOW_ZERO - show zeroed values (by default they are not shown).
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1601292670-1616-3-git-send-email-alan.maguire@oracle.com
The check_attach_btf_id() function really does three things:
1. It performs a bunch of checks on the program to ensure that the
attachment is valid.
2. It stores a bunch of state about the attachment being requested in
the verifier environment and struct bpf_prog objects.
3. It allocates a trampoline for the attachment.
This patch splits out (1.) and (3.) into separate functions which will
perform the checks, but return the computed values instead of directly
modifying the environment. This is done in preparation for reusing the
checks when the actual attachment is happening, which will allow tracing
programs to have multiple (compatible) attachments.
This also fixes a bug where a bunch of checks were skipped if a trampoline
already existed for the tracing target.
Fixes: 6ba43b761c ("bpf: Attachment verification for BPF_MODIFY_RETURN")
Fixes: 1e6c62a882 ("bpf: Introduce sleepable BPF programs")
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In preparation for moving code around, change a bunch of references to
env->log (and the verbose() logging helper) to use bpf_log() and a direct
pointer to struct bpf_verifier_log. While we're touching the function
signature, mark the 'prog' argument to bpf_check_type_match() as const.
Also enhance the bpf_verifier_log_needed() check to handle NULL pointers
for the log struct so we can re-use the code with logging disabled.
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
From the checks and commit messages for modify_return, it seems it was
never the intention that it should be possible to attach a tracing program
with expected_attach_type == BPF_MODIFY_RETURN to another BPF program.
However, check_attach_modify_return() will only look at the function name,
so if the target function starts with "security_", the attach will be
allowed even for bpf2bpf attachment.
Fix this oversight by also blocking the modification if a target program is
supplied.
Fixes: 18644cec71 ("bpf: Fix use-after-free in fmod_ret check")
Fixes: 6ba43b761c ("bpf: Attachment verification for BPF_MODIFY_RETURN")
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow passing a pointer to a BTF struct sock_common* when updating
a sockmap or sockhash. Since BTF pointers can fault and therefore be
NULL at runtime we need to add an additional !sk check to
sock_map_update_elem. Since we may be passed a request or timewait
socket we also need to check sk_fullsock. Doing this allows calling
map_update_elem on sockmap from bpf_iter context, which uses
BTF pointers.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200928090805.23343-2-lmb@cloudflare.com
Add .test_run for raw_tracepoint. Also, introduce a new feature that runs
the target program on a specific CPU. This is achieved by a new flag in
bpf_attr.test, BPF_F_TEST_RUN_ON_CPU. When this flag is set, the program
is triggered on cpu with id bpf_attr.test.cpu. This feature is needed for
BPF programs that handle perf_event and other percpu resources, as the
program can access these resource locally.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200925205432.1777-2-songliubraving@fb.com
In BPF_AND and BPF_OR alu cases we have this pattern when the src and dst
tnum is a constant.
1 dst_reg->var_off = tnum_[op](dst_reg->var_off, src_reg.var_off)
2 scalar32_min_max_[op]
3 if (known) return
4 scalar_min_max_[op]
5 if (known)
6 __mark_reg_known(dst_reg,
dst_reg->var_off.value [op] src_reg.var_off.value)
The result is in 1 we calculate the var_off value and store it in the
dst_reg. Then in 6 we duplicate this logic doing the op again on the
value.
The duplication comes from the the tnum_[op] handlers because they have
already done the value calcuation. For example this is tnum_and().
struct tnum tnum_and(struct tnum a, struct tnum b)
{
u64 alpha, beta, v;
alpha = a.value | a.mask;
beta = b.value | b.mask;
v = a.value & b.value;
return TNUM(v, alpha & beta & ~v);
}
So lets remove the redundant op calculation. Its confusing for readers
and unnecessary. Its also not harmful because those ops have the
property, r1 & r1 = r1 and r1 | r1 = r1.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch changes the bpf_sk_storage_*() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
A micro benchmark has been done on a "cgroup_skb/egress" bpf program
which does a bpf_sk_storage_get(). It was driven by netperf doing
a 4096 connected UDP_STREAM test with 64bytes packet.
The stats from "kernel.bpf_stats_enabled" shows no meaningful difference.
The sk_storage_get_btf_proto, sk_storage_delete_btf_proto,
btf_sk_storage_get_proto, and btf_sk_storage_delete_proto are
no longer needed, so they are removed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000402.3856307-1-kafai@fb.com
There is a constant need to add more fields into the bpf_tcp_sock
for the bpf programs running at tc, sock_ops...etc.
A current workaround could be to use bpf_probe_read_kernel(). However,
other than making another helper call for reading each field and missing
CO-RE, it is also not as intuitive to use as directly reading
"tp->lsndtime" for example. While already having perfmon cap to do
bpf_probe_read_kernel(), it will be much easier if the bpf prog can
directly read from the tcp_sock.
This patch tries to do that by using the existing casting-helpers
bpf_skc_to_*() whose func_proto returns a btf_id. For example, the
func_proto of bpf_skc_to_tcp_sock returns the btf_id of the
kernel "struct tcp_sock".
These helpers are also added to is_ptr_cast_function().
It ensures the returning reg (BPF_REF_0) will also carries the ref_obj_id.
That will keep the ref-tracking works properly.
The bpf_skc_to_* helpers are made available to most of the bpf prog
types in filter.c. The bpf_skc_to_* helpers will be limited by
perfmon cap.
This patch adds a ARG_PTR_TO_BTF_ID_SOCK_COMMON. The helper accepting
this arg can accept a btf-id-ptr (PTR_TO_BTF_ID + &btf_sock_ids[BTF_SOCK_TYPE_SOCK_COMMON])
or a legacy-ctx-convert-skc-ptr (PTR_TO_SOCK_COMMON). The bpf_skc_to_*()
helpers are changed to take ARG_PTR_TO_BTF_ID_SOCK_COMMON such that
they will accept pointer obtained from skb->sk.
Instead of specifying both arg_type and arg_btf_id in the same func_proto
which is how the current ARG_PTR_TO_BTF_ID does, the arg_btf_id of
the new ARG_PTR_TO_BTF_ID_SOCK_COMMON is specified in the
compatible_reg_types[] in verifier.c. The reason is the arg_btf_id is
always the same. Discussion in this thread:
https://lore.kernel.org/bpf/20200922070422.1917351-1-kafai@fb.com/
The ARG_PTR_TO_BTF_ID_ part gives a clear expectation that the helper is
expecting a PTR_TO_BTF_ID which could be NULL. This is the same
behavior as the existing helper taking ARG_PTR_TO_BTF_ID.
The _SOCK_COMMON part means the helper is also expecting the legacy
SOCK_COMMON pointer.
By excluding the _OR_NULL part, the bpf prog cannot call helper
with a literal NULL which doesn't make sense in most cases.
e.g. bpf_skc_to_tcp_sock(NULL) will be rejected. All PTR_TO_*_OR_NULL
reg has to do a NULL check first before passing into the helper or else
the bpf prog will be rejected. This behavior is nothing new and
consistent with the current expectation during bpf-prog-load.
[ ARG_PTR_TO_BTF_ID_SOCK_COMMON will be used to replace
ARG_PTR_TO_SOCK* of other existing helpers later such that
those existing helpers can take the PTR_TO_BTF_ID returned by
the bpf_skc_to_*() helpers.
The only special case is bpf_sk_lookup_assign() which can accept a
literal NULL ptr. It has to be handled specially in another follow
up patch if there is a need (e.g. by renaming ARG_PTR_TO_SOCKET_OR_NULL
to ARG_PTR_TO_BTF_ID_SOCK_COMMON_OR_NULL). ]
[ When converting the older helpers that take ARG_PTR_TO_SOCK* in
the later patch, if the kernel does not support BTF,
ARG_PTR_TO_BTF_ID_SOCK_COMMON will behave like ARG_PTR_TO_SOCK_COMMON
because no reg->type could have PTR_TO_BTF_ID in this case.
It is not a concern for the newer-btf-only helper like the bpf_skc_to_*()
here though because these helpers must require BTF vmlinux to begin
with. ]
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200925000350.3855720-1-kafai@fb.com
check_reg_type() checks whether a reg can be used as an arg of a
func_proto. For PTR_TO_BTF_ID, the check is actually not
completely done until the reg->btf_id is pointing to a
kernel struct that is acceptable by the func_proto.
Thus, this patch moves the btf_id check into check_reg_type().
"arg_type" and "arg_btf_id" are passed to check_reg_type() instead of
"compatible". The compatible_reg_types[] usage is localized in
check_reg_type() now.
The "if (!btf_id) verbose(...); " is also removed since it won't happen.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200925000344.3854828-1-kafai@fb.com
This reverts commit 31f23a6a18.
This change made many selftests/bpf flaky: flow_dissector, sk_lookup, sk_assign and others.
There was no issue in the code.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-09-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 95 non-merge commits during the last 22 day(s) which contain
a total of 124 files changed, 4211 insertions(+), 2040 deletions(-).
The main changes are:
1) Full multi function support in libbpf, from Andrii.
2) Refactoring of function argument checks, from Lorenz.
3) Make bpf_tail_call compatible with functions (subprograms), from Maciej.
4) Program metadata support, from YiFei.
5) bpf iterator optimizations, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arrays with designated initializers have an implicit length of the highest
initialized value plus one. I used this to ensure that newly added entries
in enum bpf_reg_type get a NULL entry in compatible_reg_types.
This is difficult to understand since it requires knowledge of the
peculiarities of designated initializers. Use __BPF_ARG_TYPE_MAX to size
the array instead.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200923160156.80814-1-lmb@cloudflare.com
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mapping between bpf_arg_type and bpf_reg_type is encoded in a big
hairy if statement that is hard to follow. The debug output also leaves
to be desired: if a reg_type doesn't match we only print one of the
options, instead printing all the valid ones.
Convert the if statement into a table which is then used to drive type
checking. If none of the reg_types match we print all options, e.g.:
R2 type=rdonly_buf expected=fp, pkt, pkt_meta, map_value
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-12-lmb@cloudflare.com
check_func_arg has a plethora of weird if statements with empty branches.
They work around the fact that *_OR_NULL argument types should accept a
SCALAR_VALUE register, as long as it's value is 0. These statements make
it difficult to reason about the type checking logic.
Instead, skip more detailed type checking logic iff the register is 0,
and the function expects a nullable type. This allows simplifying the type
checking itself.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-11-lmb@cloudflare.com
Move the check for PTR_TO_MAP_VALUE to check_func_arg, where all other
checking is done as well. Move the invocation of process_spin_lock away
from the register type checking, to allow a future refactoring.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-10-lmb@cloudflare.com
If we encounter a pointer to memory, we set meta->raw_mode depending
on the type of memory we point at. What isn't obvious is that this
information is only used when the next memory size argument is
encountered.
Move the assignment closer to where it's used, and add a comment that
explains what is going on.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-9-lmb@cloudflare.com
Always check context access if the register we're operating on is
PTR_TO_CTX, rather than relying on ARG_PTR_TO_CTX. This allows
simplifying the arg_type checking section of the function.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-8-lmb@cloudflare.com
Instead of dealing with reg->ref_obj_id individually for every arg type that
needs it, rely on the fact that ref_obj_id is zero if the register is not
reference tracked.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-7-lmb@cloudflare.com
Perform BTF type checks if the register we're working on contains a BTF
pointer, rather than if the argument is for a BTF pointer. This is easier
to understand, and allows removing the code from the arg_type checking
section of the function.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-6-lmb@cloudflare.com
Function prototypes using ARG_PTR_TO_BTF_ID currently use two ways to signal
which BTF IDs are acceptable. First, bpf_func_proto.btf_id is an array of
IDs, one for each argument. This array is only accessed up to the highest
numbered argument that uses ARG_PTR_TO_BTF_ID and may therefore be less than
five arguments long. It usually points at a BTF_ID_LIST. Second, check_btf_id
is a function pointer that is called by the verifier if present. It gets the
actual BTF ID of the register, and the argument number we're currently checking.
It turns out that the only user check_arg_btf_id ignores the argument, and is
simply used to check whether the BTF ID has a struct sock_common at it's start.
Replace both of these mechanisms with an explicit BTF ID for each argument
in a function proto. Thanks to btf_struct_ids_match this is very flexible:
check_arg_btf_id can be replaced by requiring struct sock_common.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-5-lmb@cloudflare.com
Move the check for a NULL or zero register to check_helper_mem_access. This
makes check_stack_boundary easier to understand.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-3-lmb@cloudflare.com
bsearch doesn't modify the contents of the array, so we can take a const pointer.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-2-lmb@cloudflare.com
The in_atomic() macro cannot always detect atomic context, in particular,
it cannot know about held spinlocks in non-preemptible kernels. Although,
there is no user call bpf_link_put() with holding spinlock now, be on the
safe side, so we can avoid this in the future.
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200917074453.20621-1-songmuchun@bytedance.com
The local_storage->list will be traversed by rcu reader in parallel.
Thus, hlist_add_head_rcu() is needed in bpf_selem_link_storage_nolock().
This patch fixes it.
This part of the code has recently been refactored in bpf-next
and this patch makes changes to the new file "bpf_local_storage.c".
Instead of using the original offending commit in the Fixes tag,
the commit that created the file "bpf_local_storage.c" is used.
A separate fix has been provided to the bpf tree.
Fixes: 450af8d0f6 ("bpf: Split bpf_local_storage to bpf_sk_storage")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200916204453.2003915-1-kafai@fb.com
LD_[ABS|IND] instructions may return from the function early. bpf_tail_call
pseudo instruction is either fallthrough or return. Allow them in the
subprograms only when subprograms are BTF annotated and have scalar return
types. Allow ld_abs and tail_call in the main program even if it calls into
subprograms. In the past that was not ok to do for ld_abs, since it was JITed
with special exit sequence. Since bpf_gen_ld_abs() was introduced the ld_abs
looks like normal exit insn from JIT point of view, so it's safe to allow them
in the main program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Relax verifier's restriction that was meant to forbid tailcall usage
when subprog count was higher than 1.
Also, do not max out the stack depth of program that utilizes tailcalls.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit serves two things:
1) it optimizes BPF prologue/epilogue generation
2) it makes possible to have tailcalls within BPF subprogram
Both points are related to each other since without 1), 2) could not be
achieved.
In [1], Alexei says:
"The prologue will look like:
nop5
xor eax,eax // two new bytes if bpf_tail_call() is used in this
// function
push rbp
mov rbp, rsp
sub rsp, rounded_stack_depth
push rax // zero init tail_call counter
variable number of push rbx,r13,r14,r15
Then bpf_tail_call will pop variable number rbx,..
and final 'pop rax'
Then 'add rsp, size_of_current_stack_frame'
jmp to next function and skip over 'nop5; xor eax,eax; push rpb; mov
rbp, rsp'
This way new function will set its own stack size and will init tail
call
counter with whatever value the parent had.
If next function doesn't use bpf_tail_call it won't have 'xor eax,eax'.
Instead it would need to have 'nop2' in there."
Implement that suggestion.
Since the layout of stack is changed, tail call counter handling can not
rely anymore on popping it to rbx just like it have been handled for
constant prologue case and later overwrite of rbx with actual value of
rbx pushed to stack. Therefore, let's use one of the register (%rcx) that
is considered to be volatile/caller-saved and pop the value of tail call
counter in there in the epilogue.
Drop the BUILD_BUG_ON in emit_prologue and in
emit_bpf_tail_call_indirect where instruction layout is not constant
anymore.
Introduce new poke target, 'tailcall_bypass' to poke descriptor that is
dedicated for skipping the register pops and stack unwind that are
generated right before the actual jump to target program.
For case when the target program is not present, BPF program will skip
the pop instructions and nop5 dedicated for jmpq $target. An example of
such state when only R6 of callee saved registers is used by program:
ffffffffc0513aa1: e9 0e 00 00 00 jmpq 0xffffffffc0513ab4
ffffffffc0513aa6: 5b pop %rbx
ffffffffc0513aa7: 58 pop %rax
ffffffffc0513aa8: 48 81 c4 00 00 00 00 add $0x0,%rsp
ffffffffc0513aaf: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
ffffffffc0513ab4: 48 89 df mov %rbx,%rdi
When target program is inserted, the jump that was there to skip
pops/nop5 will become the nop5, so CPU will go over pops and do the
actual tailcall.
One might ask why there simply can not be pushes after the nop5?
In the following example snippet:
ffffffffc037030c: 48 89 fb mov %rdi,%rbx
(...)
ffffffffc0370332: 5b pop %rbx
ffffffffc0370333: 58 pop %rax
ffffffffc0370334: 48 81 c4 00 00 00 00 add $0x0,%rsp
ffffffffc037033b: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
ffffffffc0370340: 48 81 ec 00 00 00 00 sub $0x0,%rsp
ffffffffc0370347: 50 push %rax
ffffffffc0370348: 53 push %rbx
ffffffffc0370349: 48 89 df mov %rbx,%rdi
ffffffffc037034c: e8 f7 21 00 00 callq 0xffffffffc0372548
There is the bpf2bpf call (at ffffffffc037034c) right after the tailcall
and jump target is not present. ctx is in %rbx register and BPF
subprogram that we will call into on ffffffffc037034c is relying on it,
e.g. it will pick ctx from there. Such code layout is therefore broken
as we would overwrite the content of %rbx with the value that was pushed
on the prologue. That is the reason for the 'bypass' approach.
Special care needs to be taken during the install/update/remove of
tailcall target. In case when target program is not present, the CPU
must not execute the pop instructions that precede the tailcall.
To address that, the following states can be defined:
A nop, unwind, nop
B nop, unwind, tail
C skip, unwind, nop
D skip, unwind, tail
A is forbidden (lead to incorrectness). The state transitions between
tailcall install/update/remove will work as follows:
First install tail call f: C->D->B(f)
* poke the tailcall, after that get rid of the skip
Update tail call f to f': B(f)->B(f')
* poke the tailcall (poke->tailcall_target) and do NOT touch the
poke->tailcall_bypass
Remove tail call: B(f')->C(f')
* poke->tailcall_bypass is poked back to jump, then we wait the RCU
grace period so that other programs will finish its execution and
after that we are safe to remove the poke->tailcall_target
Install new tail call (f''): C(f')->D(f'')->B(f'').
* same as first step
This way CPU can never be exposed to "unwind, tail" state.
Last but not least, when tailcalls get mixed with bpf2bpf calls, it
would be possible to encounter the endless loop due to clearing the
tailcall counter if for example we would use the tailcall3-like from BPF
selftests program that would be subprogram-based, meaning the tailcall
would be present within the BPF subprogram.
This test, broken down to particular steps, would do:
entry -> set tailcall counter to 0, bump it by 1, tailcall to func0
func0 -> call subprog_tail
(we are NOT skipping the first 11 bytes of prologue and this subprogram
has a tailcall, therefore we clear the counter...)
subprog -> do the same thing as entry
and then loop forever.
To address this, the idea is to go through the call chain of bpf2bpf progs
and look for a tailcall presence throughout whole chain. If we saw a single
tail call then each node in this call chain needs to be marked as a subprog
that can reach the tailcall. We would later feed the JIT with this info
and:
- set eax to 0 only when tailcall is reachable and this is the entry prog
- if tailcall is reachable but there's no tailcall in insns of currently
JITed prog then push rax anyway, so that it will be possible to
propagate further down the call chain
- finally if tailcall is reachable, then we need to precede the 'call'
insn with mov rax, [rbp - (stack_depth + 8)]
Tail call related cases from test_verifier kselftest are also working
fine. Sample BPF programs that utilize tail calls (sockex3, tracex5)
work properly as well.
[1]: https://lore.kernel.org/bpf/20200517043227.2gpq22ifoq37ogst@ast-mbp.dhcp.thefacebook.com/
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Protect against potential stack overflow that might happen when bpf2bpf
calls get combined with tailcalls. Limit the caller's stack depth for
such case down to 256 so that the worst case scenario would result in 8k
stack size (32 which is tailcall limit * 256 = 8k).
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reflect the actual purpose of poke->ip and rename it to
poke->tailcall_target so that it will not the be confused with another
poke target that will be introduced in next commit.
While at it, do the same thing with poke->ip_stable - rename it to
poke->tailcall_target_stable.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, there was no need for poke descriptors being present in
subprogram's bpf_prog_aux struct since tailcalls were simply not allowed
in them. Each subprog is JITed independently so in order to enable
JITing subprograms that use tailcalls, do the following:
- in fixup_bpf_calls() store the index of tailcall insn onto the generated
poke descriptor,
- in case when insn patching occurs, adjust the tailcall insn idx from
bpf_patch_insn_data,
- then in jit_subprogs() check whether the given poke descriptor belongs
to the current subprog by checking if that previously stored absolute
index of tail call insn is in the scope of the insns of given subprog,
- update the insn->imm with new poke descriptor slot so that while JITing
the proper poke descriptor will be grabbed
This way each of the main program's poke descriptors are distributed
across the subprograms poke descriptor array, so main program's
descriptors can be untracked out of the prog array map.
Add also subprog's aux struct to the BPF map poke_progs list by calling
on it map_poke_track().
In case of any error, call the map_poke_untrack() on subprog's aux
structs that have already been registered to prog array map.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 19 day(s) which contain
a total of 10 files changed, 47 insertions(+), 38 deletions(-).
The main changes are:
1) docs/bpf fixes, from Andrii.
2) ld_abs fix, from Daniel.
3) socket casting helpers fix, from Martin.
4) hash iterator fixes, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This syscall binds a map to a program. Returns success if the map is
already bound to the program.
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: YiFei Zhu <zhuyifei1999@gmail.com>
Link: https://lore.kernel.org/bpf/20200915234543.3220146-3-sdf@google.com
To support modifying the used_maps array, we use a mutex to protect
the use of the counter and the array. The mutex is initialized right
after the prog aux is allocated, and destroyed right before prog
aux is freed. This way we guarantee it's initialized for both cBPF
and eBPF.
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: YiFei Zhu <zhuyifei1999@gmail.com>
Link: https://lore.kernel.org/bpf/20200915234543.3220146-2-sdf@google.com
Header frame.h is getting more code annotations to help objtool analyze
object files.
Rename the file to objtool.h.
[ jpoimboe: add objtool.h to MAINTAINERS ]
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Using the read_iter/write_iter interfaces allows for in-kernel users
to set sysctls without using set_fs(). Also, the buffer is a string,
so give it the real type of 'char *', not void *.
[AV: Christoph's fixup folded in]
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 41c48f3a98 ("bpf: Support access
to bpf map fields") added support to access map fields
with CORE support. For example,
struct bpf_map {
__u32 max_entries;
} __attribute__((preserve_access_index));
struct bpf_array {
struct bpf_map map;
__u32 elem_size;
} __attribute__((preserve_access_index));
struct {
__uint(type, BPF_MAP_TYPE_ARRAY);
__uint(max_entries, 4);
__type(key, __u32);
__type(value, __u32);
} m_array SEC(".maps");
SEC("cgroup_skb/egress")
int cg_skb(void *ctx)
{
struct bpf_array *array = (struct bpf_array *)&m_array;
/* .. array->map.max_entries .. */
}
In kernel, bpf_htab has similar structure,
struct bpf_htab {
struct bpf_map map;
...
}
In the above cg_skb(), to access array->map.max_entries, with CORE, the clang will
generate two builtin's.
base = &m_array;
/* access array.map */
map_addr = __builtin_preserve_struct_access_info(base, 0, 0);
/* access array.map.max_entries */
max_entries_addr = __builtin_preserve_struct_access_info(map_addr, 0, 0);
max_entries = *max_entries_addr;
In the current llvm, if two builtin's are in the same function or
in the same function after inlining, the compiler is smart enough to chain
them together and generates like below:
base = &m_array;
max_entries = *(base + reloc_offset); /* reloc_offset = 0 in this case */
and we are fine.
But if we force no inlining for one of functions in test_map_ptr() selftest, e.g.,
check_default(), the above two __builtin_preserve_* will be in two different
functions. In this case, we will have code like:
func check_hash():
reloc_offset_map = 0;
base = &m_array;
map_base = base + reloc_offset_map;
check_default(map_base, ...)
func check_default(map_base, ...):
max_entries = *(map_base + reloc_offset_max_entries);
In kernel, map_ptr (CONST_PTR_TO_MAP) does not allow any arithmetic.
The above "map_base = base + reloc_offset_map" will trigger a verifier failure.
; VERIFY(check_default(&hash->map, map));
0: (18) r7 = 0xffffb4fe8018a004
2: (b4) w1 = 110
3: (63) *(u32 *)(r7 +0) = r1
R1_w=invP110 R7_w=map_value(id=0,off=4,ks=4,vs=8,imm=0) R10=fp0
; VERIFY_TYPE(BPF_MAP_TYPE_HASH, check_hash);
4: (18) r1 = 0xffffb4fe8018a000
6: (b4) w2 = 1
7: (63) *(u32 *)(r1 +0) = r2
R1_w=map_value(id=0,off=0,ks=4,vs=8,imm=0) R2_w=invP1 R7_w=map_value(id=0,off=4,ks=4,vs=8,imm=0) R10=fp0
8: (b7) r2 = 0
9: (18) r8 = 0xffff90bcb500c000
11: (18) r1 = 0xffff90bcb500c000
13: (0f) r1 += r2
R1 pointer arithmetic on map_ptr prohibited
To fix the issue, let us permit map_ptr + 0 arithmetic which will
result in exactly the same map_ptr.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200908175702.2463625-1-yhs@fb.com
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Currently, for hashmap, the bpf iterator will grab a bucket lock, a
spinlock, before traversing the elements in the bucket. This can ensure
all bpf visted elements are valid. But this mechanism may cause
deadlock if update/deletion happens to the same bucket of the
visited map in the program. For example, if we added bpf_map_update_elem()
call to the same visited element in selftests bpf_iter_bpf_hash_map.c,
we will have the following deadlock:
============================================
WARNING: possible recursive locking detected
5.9.0-rc1+ #841 Not tainted
--------------------------------------------
test_progs/1750 is trying to acquire lock:
ffff9a5bb73c5e70 (&htab->buckets[i].raw_lock){....}-{2:2}, at: htab_map_update_elem+0x1cf/0x410
but task is already holding lock:
ffff9a5bb73c5e20 (&htab->buckets[i].raw_lock){....}-{2:2}, at: bpf_hash_map_seq_find_next+0x94/0x120
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&htab->buckets[i].raw_lock);
lock(&htab->buckets[i].raw_lock);
*** DEADLOCK ***
...
Call Trace:
dump_stack+0x78/0xa0
__lock_acquire.cold.74+0x209/0x2e3
lock_acquire+0xba/0x380
? htab_map_update_elem+0x1cf/0x410
? __lock_acquire+0x639/0x20c0
_raw_spin_lock_irqsave+0x3b/0x80
? htab_map_update_elem+0x1cf/0x410
htab_map_update_elem+0x1cf/0x410
? lock_acquire+0xba/0x380
bpf_prog_ad6dab10433b135d_dump_bpf_hash_map+0x88/0xa9c
? find_held_lock+0x34/0xa0
bpf_iter_run_prog+0x81/0x16e
__bpf_hash_map_seq_show+0x145/0x180
bpf_seq_read+0xff/0x3d0
vfs_read+0xad/0x1c0
ksys_read+0x5f/0xe0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
...
The bucket_lock first grabbed in seq_ops->next() called by bpf_seq_read(),
and then grabbed again in htab_map_update_elem() in the bpf program, causing
deadlocks.
Actually, we do not need bucket_lock here, we can just use rcu_read_lock()
similar to netlink iterator where the rcu_read_{lock,unlock} likes below:
seq_ops->start():
rcu_read_lock();
seq_ops->next():
rcu_read_unlock();
/* next element */
rcu_read_lock();
seq_ops->stop();
rcu_read_unlock();
Compared to old bucket_lock mechanism, if concurrent updata/delete happens,
we may visit stale elements, miss some elements, or repeat some elements.
I think this is a reasonable compromise. For users wanting to avoid
stale, missing/repeated accesses, bpf_map batch access syscall interface
can be used.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200902235340.2001375-1-yhs@fb.com
Currently, task_file iterator iterates all files from all tasks.
This may potentially visit a lot of duplicated files if there are
many tasks sharing the same files, e.g., typical pthreads
where these pthreads and the main thread are sharing the same files.
This patch changed task_file iterator to skip a particular task
if that task shares the same files as its group_leader (the task
having the same tgid and also task->tgid == task->pid).
This will preserve the same result, visiting all files from all
tasks, and will reduce runtime cost significantl, e.g., if there are
a lot of pthreads and the process has a lot of open files.
Suggested-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/bpf/20200902023112.1672792-1-yhs@fb.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions bq_enqueue(), bq_flush_to_queue(), and bq_xmit_all() in
{cpu,dev}map.c always return zero. Changing the return type from int
to void makes the code easier to follow.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200901083928.6199-1-bjorn.topel@gmail.com
Technically the bpf programs can sleep while attached to bpf_lsm_file_mprotect,
but such programs need to access user memory. So they're in might_fault()
category. Which means they cannot be called from file_mprotect lsm hook that
takes write lock on mm->mmap_lock.
Adjust the test accordingly.
Also add might_fault() to __bpf_prog_enter_sleepable() to catch such deadlocks early.
Fixes: 1e6c62a882 ("bpf: Introduce sleepable BPF programs")
Fixes: e68a144547 ("selftests/bpf: Add sleepable tests")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200831201651.82447-1-alexei.starovoitov@gmail.com
Sleepable BPF programs can now use copy_from_user() to access user memory.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: KP Singh <kpsingh@google.com>
Link: https://lore.kernel.org/bpf/20200827220114.69225-4-alexei.starovoitov@gmail.com
Introduce sleepable BPF programs that can request such property for themselves
via BPF_F_SLEEPABLE flag at program load time. In such case they will be able
to use helpers like bpf_copy_from_user() that might sleep. At present only
fentry/fexit/fmod_ret and lsm programs can request to be sleepable and only
when they are attached to kernel functions that are known to allow sleeping.
The non-sleepable programs are relying on implicit rcu_read_lock() and
migrate_disable() to protect life time of programs, maps that they use and
per-cpu kernel structures used to pass info between bpf programs and the
kernel. The sleepable programs cannot be enclosed into rcu_read_lock().
migrate_disable() maps to preempt_disable() in non-RT kernels, so the progs
should not be enclosed in migrate_disable() as well. Therefore
rcu_read_lock_trace is used to protect the life time of sleepable progs.
There are many networking and tracing program types. In many cases the
'struct bpf_prog *' pointer itself is rcu protected within some other kernel
data structure and the kernel code is using rcu_dereference() to load that
program pointer and call BPF_PROG_RUN() on it. All these cases are not touched.
Instead sleepable bpf programs are allowed with bpf trampoline only. The
program pointers are hard-coded into generated assembly of bpf trampoline and
synchronize_rcu_tasks_trace() is used to protect the life time of the program.
The same trampoline can hold both sleepable and non-sleepable progs.
When rcu_read_lock_trace is held it means that some sleepable bpf program is
running from bpf trampoline. Those programs can use bpf arrays and preallocated
hash/lru maps. These map types are waiting on programs to complete via
synchronize_rcu_tasks_trace();
Updates to trampoline now has to do synchronize_rcu_tasks_trace() and
synchronize_rcu_tasks() to wait for sleepable progs to finish and for
trampoline assembly to finish.
This is the first step of introducing sleepable progs. Eventually dynamically
allocated hash maps can be allowed and networking program types can become
sleepable too.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: KP Singh <kpsingh@google.com>
Link: https://lore.kernel.org/bpf/20200827220114.69225-3-alexei.starovoitov@gmail.com
Most of the maps do not use max_entries during verification time.
Thus, those map_meta_equal() do not need to enforce max_entries
when it is inserted as an inner map during runtime. The max_entries
check is removed from the default implementation bpf_map_meta_equal().
The prog_array_map and xsk_map are exception. Its map_gen_lookup
uses max_entries to generate inline lookup code. Thus, they will
implement its own map_meta_equal() to enforce max_entries.
Since there are only two cases now, the max_entries check
is not refactored and stays in its own .c file.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200828011813.1970516-1-kafai@fb.com
Some properties of the inner map is used in the verification time.
When an inner map is inserted to an outer map at runtime,
bpf_map_meta_equal() is currently used to ensure those properties
of the inserting inner map stays the same as the verification
time.
In particular, the current bpf_map_meta_equal() checks max_entries which
turns out to be too restrictive for most of the maps which do not use
max_entries during the verification time. It limits the use case that
wants to replace a smaller inner map with a larger inner map. There are
some maps do use max_entries during verification though. For example,
the map_gen_lookup in array_map_ops uses the max_entries to generate
the inline lookup code.
To accommodate differences between maps, the map_meta_equal is added
to bpf_map_ops. Each map-type can decide what to check when its
map is used as an inner map during runtime.
Also, some map types cannot be used as an inner map and they are
currently black listed in bpf_map_meta_alloc() in map_in_map.c.
It is not unusual that the new map types may not aware that such
blacklist exists. This patch enforces an explicit opt-in
and only allows a map to be used as an inner map if it has
implemented the map_meta_equal ops. It is based on the
discussion in [1].
All maps that support inner map has its map_meta_equal points
to bpf_map_meta_equal in this patch. A later patch will
relax the max_entries check for most maps. bpf_types.h
counts 28 map types. This patch adds 23 ".map_meta_equal"
by using coccinelle. -5 for
BPF_MAP_TYPE_PROG_ARRAY
BPF_MAP_TYPE_(PERCPU)_CGROUP_STORAGE
BPF_MAP_TYPE_STRUCT_OPS
BPF_MAP_TYPE_ARRAY_OF_MAPS
BPF_MAP_TYPE_HASH_OF_MAPS
The "if (inner_map->inner_map_meta)" check in bpf_map_meta_alloc()
is moved such that the same error is returned.
[1]: https://lore.kernel.org/bpf/20200522022342.899756-1-kafai@fb.com/
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200828011806.1970400-1-kafai@fb.com
bpf selftest test_progs/test_sk_assign failed with llvm 11 and llvm 12.
Compared to llvm 10, llvm 11 and 12 generates xor instruction which
is not handled properly in verifier. The following illustrates the
problem:
16: (b4) w5 = 0
17: ... R5_w=inv0 ...
...
132: (a4) w5 ^= 1
133: ... R5_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) ...
...
37: (bc) w8 = w5
38: ... R5=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff))
R8_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) ...
...
41: (bc) w3 = w8
42: ... R3_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) ...
45: (56) if w3 != 0x0 goto pc+1
... R3_w=inv0 ...
46: (b7) r1 = 34
47: R1_w=inv34 R7=pkt(id=0,off=26,r=38,imm=0)
47: (0f) r7 += r1
48: R1_w=invP34 R3_w=inv0 R7_w=pkt(id=0,off=60,r=38,imm=0)
48: (b4) w9 = 0
49: R1_w=invP34 R3_w=inv0 R7_w=pkt(id=0,off=60,r=38,imm=0)
49: (69) r1 = *(u16 *)(r7 +0)
invalid access to packet, off=60 size=2, R7(id=0,off=60,r=38)
R7 offset is outside of the packet
At above insn 132, w5 = 0, but after w5 ^= 1, we give a really conservative
value of w5. At insn 45, in reality the condition should be always false.
But due to conservative value for w3, the verifier evaluates it could be
true and this later leads to verifier failure complaining potential
packet out-of-bound access.
This patch implemented proper XOR support in verifier.
In the above example, we have:
132: R5=invP0
132: (a4) w5 ^= 1
133: R5_w=invP1
...
37: (bc) w8 = w5
...
41: (bc) w3 = w8
42: R3_w=invP1
...
45: (56) if w3 != 0x0 goto pc+1
47: R3_w=invP1
...
processed 353 insns ...
and the verifier can verify the program successfully.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200825064608.2017937-1-yhs@fb.com
This patch adds changes in verifier to make decisions such as granting
of read / write access or enforcement of return code status based on
the program type of the target program while using dynamic program
extension (of type BPF_PROG_TYPE_EXT).
The BPF_PROG_TYPE_EXT type can be used to extend types such as XDP, SKB
and others. Since the BPF_PROG_TYPE_EXT program type on itself is just a
placeholder for those, we need this extended check for those extended
programs to actually work with proper access, while using this option.
Specifically, it introduces following changes:
- may_access_direct_pkt_data:
allow access to packet data based on the target prog
- check_return_code:
enforce return code based on the target prog
(currently, this check is skipped for EXT program)
- check_ld_abs:
check for 'may_access_skb' based on the target prog
- check_map_prog_compatibility:
enforce the map compatibility check based on the target prog
- may_update_sockmap:
allow sockmap update based on the target prog
Some other occurrences of prog->type is left as it without replacing
with the 'resolved' type:
- do_check_common() and check_attach_btf_id():
already have specific logic to handle the EXT prog type
- jit_subprogs() and bpf_check():
Not changed for jit compilation or while inferring env->ops
Next few patches in this series include selftests for some of these cases.
Signed-off-by: Udip Pant <udippant@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200825232003.2877030-2-udippant@fb.com
Adding support to define sorted set of BTF ID values.
Following defines sorted set of BTF ID values:
BTF_SET_START(btf_allowlist_d_path)
BTF_ID(func, vfs_truncate)
BTF_ID(func, vfs_fallocate)
BTF_ID(func, dentry_open)
BTF_ID(func, vfs_getattr)
BTF_ID(func, filp_close)
BTF_SET_END(btf_allowlist_d_path)
It defines following 'struct btf_id_set' variable to access
values and count:
struct btf_id_set btf_allowlist_d_path;
Adding 'allowed' callback to struct bpf_func_proto, to allow
verifier the check on allowed callers.
Adding btf_id_set_contains function, which will be used by
allowed callbacks to verify the caller's BTF ID value is
within allowed set.
Also removing extra '\' in __BTF_ID_LIST macro.
Added BTF_SET_START_GLOBAL macro for global sets.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-10-jolsa@kernel.org
Adding btf_struct_ids_match function to check if given address provided
by BTF object + offset is also address of another nested BTF object.
This allows to pass an argument to helper, which is defined via parent
BTF object + offset, like for bpf_d_path (added in following changes):
SEC("fentry/filp_close")
int BPF_PROG(prog_close, struct file *file, void *id)
{
...
ret = bpf_d_path(&file->f_path, ...
The first bpf_d_path argument is hold by verifier as BTF file object
plus offset of f_path member.
The btf_struct_ids_match function will walk the struct file object and
check if there's nested struct path object on the given offset.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-9-jolsa@kernel.org
Adding btf_struct_walk function that walks through the
struct type + given offset and returns following values:
enum bpf_struct_walk_result {
/* < 0 error */
WALK_SCALAR = 0,
WALK_PTR,
WALK_STRUCT,
};
WALK_SCALAR - when SCALAR_VALUE is found
WALK_PTR - when pointer value is found, its ID is stored
in 'next_btf_id' output param
WALK_STRUCT - when nested struct object is found, its ID is stored
in 'next_btf_id' output param
It will be used in following patches to get all nested
struct objects for given type and offset.
The btf_struct_access now calls btf_struct_walk function,
as long as it gets nested structs as return value.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-8-jolsa@kernel.org
Andrii suggested we can simply jump to again label
instead of making recursion call.
Suggested-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-7-jolsa@kernel.org
Adding type_id pointer as argument to __btf_resolve_size
to return also BTF ID of the resolved type. It will be
used in following changes.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-6-jolsa@kernel.org
If the resolved type is array, make btf_resolve_size return also
ID of the elem type. It will be needed in following changes.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-5-jolsa@kernel.org
Moving btf_resolve_size into __btf_resolve_size and
keeping btf_resolve_size public with just first 3
arguments, because the rest of the arguments are not
used by outside callers.
Following changes are adding more arguments, which
are not useful to outside callers. They will be added
to the __btf_resolve_size function.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200825192124.710397-4-jolsa@kernel.org
The CC_CAN_LINK checks that the host compiler can link, but bpf_preload
relies on libbpf which in turn needs libelf to be present during linking.
allmodconfig runs in odd setups with cross compilers and missing host
libraries like libelf. Instead of extending kconfig with every possible
library that bpf_preload might need disallow building BPF_PRELOAD in
such build-only configurations.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Adds support for both bpf_{sk, inode}_storage_{get, delete} to be used
in LSM programs. These helpers are not used for tracing programs
(currently) as their usage is tied to the life-cycle of the object and
should only be used where the owning object won't be freed (when the
owning object is passed as an argument to the LSM hook). Thus, they
are safer to use in LSM hooks than tracing. Usage of local storage in
tracing programs will probably follow a per function based whitelist
approach.
Since the UAPI helper signature for bpf_sk_storage expect a bpf_sock,
it, leads to a compilation warning for LSM programs, it's also updated
to accept a void * pointer instead.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200825182919.1118197-7-kpsingh@chromium.org
Similar to bpf_local_storage for sockets, add local storage for inodes.
The life-cycle of storage is managed with the life-cycle of the inode.
i.e. the storage is destroyed along with the owning inode.
The BPF LSM allocates an __rcu pointer to the bpf_local_storage in the
security blob which are now stackable and can co-exist with other LSMs.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200825182919.1118197-6-kpsingh@chromium.org
Commit f2e10bff16 ("bpf: Add support for BPF_OBJ_GET_INFO_BY_FD for bpf_link")
added link query for raw_tp. One of fields in link_info is to
fill a user buffer with tp_name. The Scurrent checking only
declares "ulen && !ubuf" as invalid. So "!ulen && ubuf" will be
valid. Later on, we do "copy_to_user(ubuf, tp_name, ulen - 1)" which
may overwrite user memory incorrectly.
This patch fixed the problem by disallowing "!ulen && ubuf" case as well.
Fixes: f2e10bff16 ("bpf: Add support for BPF_OBJ_GET_INFO_BY_FD for bpf_link")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200821191054.714731-1-yhs@fb.com
Allow calling bpf_map_update_elem on sockmap and sockhash from a BPF
context. The synchronization required for this is a bit fiddly: we
need to prevent the socket from changing its state while we add it
to the sockmap, since we rely on getting a callback via
sk_prot->unhash. However, we can't just lock_sock like in
sock_map_sk_acquire because that might sleep. So instead we disable
softirq processing and use bh_lock_sock to prevent further
modification.
Yet, this is still not enough. BPF can be called in contexts where
the current CPU might have locked a socket. If the BPF can get
a hold of such a socket, inserting it into a sockmap would lead to
a deadlock. One straight forward example are sock_ops programs that
have ctx->sk, but the same problem exists for kprobes, etc.
We deal with this by allowing sockmap updates only from known safe
contexts. Improper usage is rejected by the verifier.
I've audited the enabled contexts to make sure they can't run in
a locked context. It's possible that CGROUP_SKB and others are
safe as well, but the auditing here is much more difficult. In
any case, we can extend the safe contexts when the need arises.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200821102948.21918-6-lmb@cloudflare.com
The verifier assumes that map values are simple blobs of memory, and
therefore treats ARG_PTR_TO_MAP_VALUE, etc. as such. However, there are
map types where this isn't true. For example, sockmap and sockhash store
sockets. In general this isn't a big problem: we can just
write helpers that explicitly requests PTR_TO_SOCKET instead of
ARG_PTR_TO_MAP_VALUE.
The one exception are the standard map helpers like map_update_elem,
map_lookup_elem, etc. Here it would be nice we could overload the
function prototype for different kinds of maps. Unfortunately, this
isn't entirely straight forward:
We only know the type of the map once we have resolved meta->map_ptr
in check_func_arg. This means we can't swap out the prototype
in check_helper_call until we're half way through the function.
Instead, modify check_func_arg to treat ARG_PTR_TO_MAP_VALUE to
mean "the native type for the map" instead of "pointer to memory"
for sockmap and sockhash. This means we don't have to modify the
function prototype at all
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200821102948.21918-5-lmb@cloudflare.com
Don't go via map->ops to call sock_map_update_elem, since we know
what function to call in bpf_map_update_value. Since we currently
don't allow calling map_update_elem from BPF context, we can remove
ops->map_update_elem and rename the function to sock_map_update_elem_sys.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200821102948.21918-4-lmb@cloudflare.com
For bpf_map_elem and bpf_sk_local_storage bpf iterators,
additional map_id should be shown for fdinfo and
userspace query. For example, the following is for
a bpf_map_elem iterator.
$ cat /proc/1753/fdinfo/9
pos: 0
flags: 02000000
mnt_id: 14
link_type: iter
link_id: 34
prog_tag: 104be6d3fe45e6aa
prog_id: 173
target_name: bpf_map_elem
map_id: 127
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200821184419.574240-1-yhs@fb.com
This patch implemented bpf_link callback functions
show_fdinfo and fill_link_info to support link_query
interface.
The general interface for show_fdinfo and fill_link_info
will print/fill the target_name. Each targets can
register show_fdinfo and fill_link_info callbacks
to print/fill more target specific information.
For example, the below is a fdinfo result for a bpf
task iterator.
$ cat /proc/1749/fdinfo/7
pos: 0
flags: 02000000
mnt_id: 14
link_type: iter
link_id: 11
prog_tag: 990e1f8152f7e54f
prog_id: 59
target_name: task
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200821184418.574122-1-yhs@fb.com
Add kernel module with user mode driver that populates bpffs with
BPF iterators.
$ mount bpffs /my/bpffs/ -t bpf
$ ls -la /my/bpffs/
total 4
drwxrwxrwt 2 root root 0 Jul 2 00:27 .
drwxr-xr-x 19 root root 4096 Jul 2 00:09 ..
-rw------- 1 root root 0 Jul 2 00:27 maps.debug
-rw------- 1 root root 0 Jul 2 00:27 progs.debug
The user mode driver will load BPF Type Formats, create BPF maps, populate BPF
maps, load two BPF programs, attach them to BPF iterators, and finally send two
bpf_link IDs back to the kernel.
The kernel will pin two bpf_links into newly mounted bpffs instance under
names "progs.debug" and "maps.debug". These two files become human readable.
$ cat /my/bpffs/progs.debug
id name attached
11 dump_bpf_map bpf_iter_bpf_map
12 dump_bpf_prog bpf_iter_bpf_prog
27 test_pkt_access
32 test_main test_pkt_access test_pkt_access
33 test_subprog1 test_pkt_access_subprog1 test_pkt_access
34 test_subprog2 test_pkt_access_subprog2 test_pkt_access
35 test_subprog3 test_pkt_access_subprog3 test_pkt_access
36 new_get_skb_len get_skb_len test_pkt_access
37 new_get_skb_ifindex get_skb_ifindex test_pkt_access
38 new_get_constant get_constant test_pkt_access
The BPF program dump_bpf_prog() in iterators.bpf.c is printing this data about
all BPF programs currently loaded in the system. This information is unstable
and will change from kernel to kernel as ".debug" suffix conveys.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200819042759.51280-4-alexei.starovoitov@gmail.com
The program and map iterators work similar to seq_file-s.
Once the program is pinned in bpffs it can be read with "cat" tool
to print human readable output. In this case about BPF programs and maps.
For example:
$ cat /sys/fs/bpf/progs.debug
id name attached
5 dump_bpf_map bpf_iter_bpf_map
6 dump_bpf_prog bpf_iter_bpf_prog
$ cat /sys/fs/bpf/maps.debug
id name max_entries
3 iterator.rodata 1
To avoid kernel build dependency on clang 10 separate bpf skeleton generation
into manual "make" step and instead check-in generated .skel.h into git.
Unlike 'bpftool prog show' in-kernel BTF name is used (when available)
to print full name of BPF program instead of 16-byte truncated name.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200819042759.51280-3-alexei.starovoitov@gmail.com
Refactor the code a bit to extract bpf_link_by_id() helper.
It's similar to existing bpf_prog_by_id().
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200819042759.51280-2-alexei.starovoitov@gmail.com
Currently when traversing all tasks, the next tid
is always increased by one. This may result in
visiting the same task multiple times in a
pid namespace.
This patch fixed the issue by seting the next
tid as pid_nr_ns(pid, ns) + 1, similar to
funciton next_tgid().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lore.kernel.org/bpf/20200818222310.2181500-1-yhs@fb.com
In our production system, we observed rcu stalls when
'bpftool prog` is running.
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: \x097-....: (20999 ticks this GP) idle=302/1/0x4000000000000000 softirq=1508852/1508852 fqs=4913
\x09(t=21031 jiffies g=2534773 q=179750)
NMI backtrace for cpu 7
CPU: 7 PID: 184195 Comm: bpftool Kdump: loaded Tainted: G W 5.8.0-00004-g68bfc7f8c1b4 #6
Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A17 05/03/2019
Call Trace:
<IRQ>
dump_stack+0x57/0x70
nmi_cpu_backtrace.cold+0x14/0x53
? lapic_can_unplug_cpu.cold+0x39/0x39
nmi_trigger_cpumask_backtrace+0xb7/0xc7
rcu_dump_cpu_stacks+0xa2/0xd0
rcu_sched_clock_irq.cold+0x1ff/0x3d9
? tick_nohz_handler+0x100/0x100
update_process_times+0x5b/0x90
tick_sched_timer+0x5e/0xf0
__hrtimer_run_queues+0x12a/0x2a0
hrtimer_interrupt+0x10e/0x280
__sysvec_apic_timer_interrupt+0x51/0xe0
asm_call_on_stack+0xf/0x20
</IRQ>
sysvec_apic_timer_interrupt+0x6f/0x80
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0010:task_file_seq_get_next+0x71/0x220
Code: 00 00 8b 53 1c 49 8b 7d 00 89 d6 48 8b 47 20 44 8b 18 41 39 d3 76 75 48 8b 4f 20 8b 01 39 d0 76 61 41 89 d1 49 39 c1 48 19 c0 <48> 8b 49 08 21 d0 48 8d 04 c1 4c 8b 08 4d 85 c9 74 46 49 8b 41 38
RSP: 0018:ffffc90006223e10 EFLAGS: 00000297
RAX: ffffffffffffffff RBX: ffff888f0d172388 RCX: ffff888c8c07c1c0
RDX: 00000000000f017b RSI: 00000000000f017b RDI: ffff888c254702c0
RBP: ffffc90006223e68 R08: ffff888be2a1c140 R09: 00000000000f017b
R10: 0000000000000002 R11: 0000000000100000 R12: ffff888f23c24118
R13: ffffc90006223e60 R14: ffffffff828509a0 R15: 00000000ffffffff
task_file_seq_next+0x52/0xa0
bpf_seq_read+0xb9/0x320
vfs_read+0x9d/0x180
ksys_read+0x5f/0xe0
do_syscall_64+0x38/0x60
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f8815f4f76e
Code: c0 e9 f6 fe ff ff 55 48 8d 3d 76 70 0a 00 48 89 e5 e8 36 06 02 00 66 0f 1f 44 00 00 64 8b 04 25 18 00 00 00 85 c0 75 14 0f 05 <48> 3d 00 f0 ff ff 77 52 c3 66 0f 1f 84 00 00 00 00 00 55 48 89 e5
RSP: 002b:00007fff8f9df578 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 000000000170b9c0 RCX: 00007f8815f4f76e
RDX: 0000000000001000 RSI: 00007fff8f9df5b0 RDI: 0000000000000007
RBP: 00007fff8f9e05f0 R08: 0000000000000049 R09: 0000000000000010
R10: 00007f881601fa40 R11: 0000000000000246 R12: 00007fff8f9e05a8
R13: 00007fff8f9e05a8 R14: 0000000001917f90 R15: 000000000000e22e
Note that `bpftool prog` actually calls a task_file bpf iterator
program to establish an association between prog/map/link/btf anon
files and processes.
In the case where the above rcu stall occured, we had a process
having 1587 tasks and each task having roughly 81305 files.
This implied 129 million bpf prog invocations. Unfortunwtely none of
these files are prog/map/link/btf files so bpf iterator/prog needs
to traverse all these files and not able to return to user space
since there are no seq_file buffer overflow.
This patch fixed the issue in bpf_seq_read() to limit the number
of visited objects. If the maximum number of visited objects is
reached, no more objects will be visited in the current syscall.
If there is nothing written in the seq_file buffer, -EAGAIN will
return to the user so user can try again.
The maximum number of visited objects is set at 1 million.
In our Intel Xeon D-2191 2.3GHZ 18-core server, bpf_seq_read()
visiting 1 million files takes around 0.18 seconds.
We did not use cond_resched() since for some iterators, e.g.,
netlink iterator, where rcu read_lock critical section spans between
consecutive seq_ops->next(), which makes impossible to do cond_resched()
in the key while loop of function bpf_seq_read().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/bpf/20200818222309.2181348-1-yhs@fb.com
With latest `bpftool prog` command, we observed the following kernel
panic.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
PGD dfe894067 P4D dfe894067 PUD deb663067 PMD 0
Oops: 0010 [#1] SMP
CPU: 9 PID: 6023 ...
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0000:ffffc900002b8f18 EFLAGS: 00010286
RAX: ffff8883a405f400 RBX: ffff888e46a6bf00 RCX: 000000008020000c
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8883a405f400
RBP: ffff888e46a6bf50 R08: 0000000000000000 R09: ffffffff81129600
R10: ffff8883a405f300 R11: 0000160000000000 R12: 0000000000002710
R13: 000000e9494b690c R14: 0000000000000202 R15: 0000000000000009
FS: 00007fd9187fe700(0000) GS:ffff888e46a40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 0000000de5d33002 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
rcu_core+0x1a4/0x440
__do_softirq+0xd3/0x2c8
irq_exit+0x9d/0xa0
smp_apic_timer_interrupt+0x68/0x120
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0033:0x47ce80
Code: Bad RIP value.
RSP: 002b:00007fd9187fba40 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13
RAX: 0000000000000002 RBX: 00007fd931789160 RCX: 000000000000010c
RDX: 00007fd9308cdfb4 RSI: 00007fd9308cdfb4 RDI: 00007ffedd1ea0a8
RBP: 00007fd9187fbab0 R08: 000000000000000e R09: 000000000000002a
R10: 0000000000480210 R11: 00007fd9187fc570 R12: 00007fd9316cc400
R13: 0000000000000118 R14: 00007fd9308cdfb4 R15: 00007fd9317a9380
After further analysis, the bug is triggered by
Commit eaaacd2391 ("bpf: Add task and task/file iterator targets")
which introduced task_file bpf iterator, which traverses all open file
descriptors for all tasks in the current namespace.
The latest `bpftool prog` calls a task_file bpf program to traverse
all files in the system in order to associate processes with progs/maps, etc.
When traversing files for a given task, rcu read_lock is taken to
access all files in a file_struct. But it used get_file() to grab
a file, which is not right. It is possible file->f_count is 0 and
get_file() will unconditionally increase it.
Later put_file() may cause all kind of issues with the above
as one of sympotoms.
The failure can be reproduced with the following steps in a few seconds:
$ cat t.c
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#define N 10000
int fd[N];
int main() {
int i;
for (i = 0; i < N; i++) {
fd[i] = open("./note.txt", 'r');
if (fd[i] < 0) {
fprintf(stderr, "failed\n");
return -1;
}
}
for (i = 0; i < N; i++)
close(fd[i]);
return 0;
}
$ gcc -O2 t.c
$ cat run.sh
#/bin/bash
for i in {1..100}
do
while true; do ./a.out; done &
done
$ ./run.sh
$ while true; do bpftool prog >& /dev/null; done
This patch used get_file_rcu() which only grabs a file if the
file->f_count is not zero. This is to ensure the file pointer
is always valid. The above reproducer did not fail for more
than 30 minutes.
Fixes: eaaacd2391 ("bpf: Add task and task/file iterator targets")
Suggested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/bpf/20200817174214.252601-1-yhs@fb.com
Currently when we look for build id within bpf_get_stackid helper
call, we check the first NOTE section and we fail if build id is
not there.
However on some system (Fedora) there can be multiple NOTE sections
in binaries and build id data is not always the first one, like:
$ readelf -a /usr/bin/ls
...
[ 2] .note.gnu.propert NOTE 0000000000000338 00000338
0000000000000020 0000000000000000 A 0 0 8358
[ 3] .note.gnu.build-i NOTE 0000000000000358 00000358
0000000000000024 0000000000000000 A 0 0 437c
[ 4] .note.ABI-tag NOTE 000000000000037c 0000037c
...
So the stack_map_get_build_id function will fail on build id retrieval
and fallback to BPF_STACK_BUILD_ID_IP.
This patch is changing the stack_map_get_build_id code to iterate
through all the NOTE sections and try to get build id data from
each of them.
When tracing on sched_switch tracepoint that does bpf_get_stackid
helper call kernel build, I can see about 60% increase of successful
build id retrieval. The rest seems fails on -EFAULT.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200812123102.20032-1-jolsa@kernel.org
Commit a5cbe05a66 ("bpf: Implement bpf iterator for
map elements") added bpf iterator support for
map elements. The map element bpf iterator requires
info to identify a particular map. In the above
commit, the attr->link_create.target_fd is used
to carry map_fd and an enum bpf_iter_link_info
is added to uapi to specify the target_fd actually
representing a map_fd:
enum bpf_iter_link_info {
BPF_ITER_LINK_UNSPEC = 0,
BPF_ITER_LINK_MAP_FD = 1,
MAX_BPF_ITER_LINK_INFO,
};
This is an extensible approach as we can grow
enumerator for pid, cgroup_id, etc. and we can
unionize target_fd for pid, cgroup_id, etc.
But in the future, there are chances that
more complex customization may happen, e.g.,
for tasks, it could be filtered based on
both cgroup_id and user_id.
This patch changed the uapi to have fields
__aligned_u64 iter_info;
__u32 iter_info_len;
for additional iter_info for link_create.
The iter_info is defined as
union bpf_iter_link_info {
struct {
__u32 map_fd;
} map;
};
So future extension for additional customization
will be easier. The bpf_iter_link_info will be
passed to target callback to validate and generic
bpf_iter framework does not need to deal it any
more.
Note that map_fd = 0 will be considered invalid
and -EBADF will be returned to user space.
Fixes: a5cbe05a66 ("bpf: Implement bpf iterator for map elements")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200805055056.1457463-1-yhs@fb.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LINK_DETACH command to force-detach bpf_link without destroying it. It has
the same behavior as auto-detaching of bpf_link due to cgroup dying for
bpf_cgroup_link or net_device being destroyed for bpf_xdp_link. In such case,
bpf_link is still a valid kernel object, but is defuncts and doesn't hold BPF
program attached to corresponding BPF hook. This functionality allows users
with enough access rights to manually force-detach attached bpf_link without
killing respective owner process.
This patch implements LINK_DETACH for cgroup, xdp, and netns links, mostly
re-using existing link release handling code.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200731182830.286260-2-andriin@fb.com
Daniel Borkmann says:
====================
pull-request: bpf 2020-07-31
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 21 day(s) which contain
a total of 5 files changed, 126 insertions(+), 18 deletions(-).
The main changes are:
1) Fix a map element leak in HASH_OF_MAPS map type, from Andrii Nakryiko.
2) Fix a NULL pointer dereference in __btf_resolve_helper_id() when no
btf_vmlinux is available, from Peilin Ye.
3) Init pos variable in __bpfilter_process_sockopt(), from Christoph Hellwig.
4) Fix a cgroup sockopt verifier test by specifying expected attach type,
from Jean-Philippe Brucker.
Note that when net gets merged into net-next later on, there is a small
merge conflict in kernel/bpf/btf.c between commit 5b801dfb7f ("bpf: Fix
NULL pointer dereference in __btf_resolve_helper_id()") from the bpf tree
and commit 138b9a0511 ("bpf: Remove btf_id helpers resolving") from the
net-next tree.
Resolve as follows: remove the old hunk with the __btf_resolve_helper_id()
function. Change the btf_resolve_helper_id() so it actually tests for a
NULL btf_vmlinux and bails out:
int btf_resolve_helper_id(struct bpf_verifier_log *log,
const struct bpf_func_proto *fn, int arg)
{
int id;
if (fn->arg_type[arg] != ARG_PTR_TO_BTF_ID || !btf_vmlinux)
return -EINVAL;
id = fn->btf_id[arg];
if (!id || id > btf_vmlinux->nr_types)
return -EINVAL;
return id;
}
Let me know if you run into any others issues (CC'ing Jiri Olsa so he's in
the loop with regards to merge conflict resolution).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline characters are added in two verifier error messages,
refactored in Commit afbf21dce6 ("bpf: Support readonly/readwrite
buffers in verifier"). This way, they do not mix with
messages afterwards.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200728221801.1090349-1-yhs@fb.com
Fix HASH_OF_MAPS bug of not putting inner map pointer on bpf_map_elem_update()
operation. This is due to per-cpu extra_elems optimization, which bypassed
free_htab_elem() logic doing proper clean ups. Make sure that inner map is put
properly in optimized case as well.
Fixes: 8c290e60fa ("bpf: fix hashmap extra_elems logic")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200729040913.2815687-1-andriin@fb.com
Entire net/core subsystem is not built without CONFIG_NET. linux/netdevice.h
just assumes that it's always there, so the easiest way to fix this is to
conditionally compile out bpf_xdp_link_attach() use in bpf/syscall.c.
Fixes: aa8d3a716b ("bpf, xdp: Add bpf_link-based XDP attachment API")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200728190527.110830-1-andriin@fb.com
There are a couple of arguments of the boolean flag zero_size_allowed and
the char pointer buf_info when calling to function check_buffer_access that
are swapped by mistake. Fix these by swapping them to correct the argument
ordering.
Fixes: afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier")
Addresses-Coverity: ("Array compared to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200727175411.155179-1-colin.king@canonical.com
Add bpf_link-based API (bpf_xdp_link) to attach BPF XDP program through
BPF_LINK_CREATE command.
bpf_xdp_link is mutually exclusive with direct BPF program attachment,
previous BPF program should be detached prior to attempting to create a new
bpf_xdp_link attachment (for a given XDP mode). Once BPF link is attached, it
can't be replaced by other BPF program attachment or link attachment. It will
be detached only when the last BPF link FD is closed.
bpf_xdp_link will be auto-detached when net_device is shutdown, similarly to
how other BPF links behave (cgroup, flow_dissector). At that point bpf_link
will become defunct, but won't be destroyed until last FD is closed.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-5-andriin@fb.com
Architectures like s390, powerpc, arm64, riscv have speical definition of
bpf_user_pt_regs_t. So we need to cast the pointer before passing it to
bpf_get_stack(). This is similar to bpf_get_stack_tp().
Fixes: 03d42fd2d83f ("bpf: Separate bpf_get_[stack|stackid] for perf events BPF")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200724200503.3629591-1-songliubraving@fb.com
local_storage.o has its compile guard as CONFIG_BPF_SYSCALL, which
does not imply that CONFIG_CGROUP is on. Including cgroup-internal.h
when CONFIG_CGROUP is off cause a compilation failure.
Fixes: f67cfc233706 ("bpf: Make cgroup storages shared between programs on the same cgroup")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200724211753.902969-1-zhuyifei1999@gmail.com
This change comes in several parts:
One, the restriction that the CGROUP_STORAGE map can only be used
by one program is removed. This results in the removal of the field
'aux' in struct bpf_cgroup_storage_map, and removal of relevant
code associated with the field, and removal of now-noop functions
bpf_free_cgroup_storage and bpf_cgroup_storage_release.
Second, we permit a key of type u64 as the key to the map.
Providing such a key type indicates that the map should ignore
attach type when comparing map keys. However, for simplicity newly
linked storage will still have the attach type at link time in
its key struct. cgroup_storage_check_btf is adapted to accept
u64 as the type of the key.
Third, because the storages are now shared, the storages cannot
be unconditionally freed on program detach. There could be two
ways to solve this issue:
* A. Reference count the usage of the storages, and free when the
last program is detached.
* B. Free only when the storage is impossible to be referred to
again, i.e. when either the cgroup_bpf it is attached to, or
the map itself, is freed.
Option A has the side effect that, when the user detach and
reattach a program, whether the program gets a fresh storage
depends on whether there is another program attached using that
storage. This could trigger races if the user is multi-threaded,
and since nondeterminism in data races is evil, go with option B.
The both the map and the cgroup_bpf now tracks their associated
storages, and the storage unlink and free are removed from
cgroup_bpf_detach and added to cgroup_bpf_release and
cgroup_storage_map_free. The latter also new holds the cgroup_mutex
to prevent any races with the former.
Fourth, on attach, we reuse the old storage if the key already
exists in the map, via cgroup_storage_lookup. If the storage
does not exist yet, we create a new one, and publish it at the
last step in the attach process. This does not create a race
condition because for the whole attach the cgroup_mutex is held.
We keep track of an array of new storages that was allocated
and if the process fails only the new storages would get freed.
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/d5401c6106728a00890401190db40020a1f84ff1.1595565795.git.zhuyifei@google.com
bpf_get_[stack|stackid] on perf_events with precise_ip uses callchain
attached to perf_sample_data. If this callchain is not presented, do not
allow attaching BPF program that calls bpf_get_[stack|stackid] to this
event.
In the error case, -EPROTO is returned so that libbpf can identify this
error and print proper hint message.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723180648.1429892-3-songliubraving@fb.com
Calling get_perf_callchain() on perf_events from PEBS entries may cause
unwinder errors. To fix this issue, the callchain is fetched early. Such
perf_events are marked with __PERF_SAMPLE_CALLCHAIN_EARLY.
Similarly, calling bpf_get_[stack|stackid] on perf_events from PEBS may
also cause unwinder errors. To fix this, add separate version of these
two helpers, bpf_get_[stack|stackid]_pe. These two hepers use callchain in
bpf_perf_event_data_kern->data->callchain.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723180648.1429892-2-songliubraving@fb.com
The bpf iterators for array and percpu array
are implemented. Similar to hash maps, for percpu
array map, bpf program will receive values
from all cpus.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184115.590532-1-yhs@fb.com
The bpf iterators for hash, percpu hash, lru hash
and lru percpu hash are implemented. During link time,
bpf_iter_reg->check_target() will check map type
and ensure the program access key/value region is
within the map defined key/value size limit.
For percpu hash and lru hash maps, the bpf program
will receive values for all cpus. The map element
bpf iterator infrastructure will prepare value
properly before passing the value pointer to the
bpf program.
This patch set supports readonly map keys and
read/write map values. It does not support deleting
map elements, e.g., from hash tables. If there is
a user case for this, the following mechanism can
be used to support map deletion for hashtab, etc.
- permit a new bpf program return value, e.g., 2,
to let bpf iterator know the map element should
be removed.
- since bucket lock is taken, the map element will be
queued.
- once bucket lock is released after all elements under
this bucket are traversed, all to-be-deleted map
elements can be deleted.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184114.590470-1-yhs@fb.com
The bpf iterator for map elements are implemented.
The bpf program will receive four parameters:
bpf_iter_meta *meta: the meta data
bpf_map *map: the bpf_map whose elements are traversed
void *key: the key of one element
void *value: the value of the same element
Here, meta and map pointers are always valid, and
key has register type PTR_TO_RDONLY_BUF_OR_NULL and
value has register type PTR_TO_RDWR_BUF_OR_NULL.
The kernel will track the access range of key and value
during verification time. Later, these values will be compared
against the values in the actual map to ensure all accesses
are within range.
A new field iter_seq_info is added to bpf_map_ops which
is used to add map type specific information, i.e., seq_ops,
init/fini seq_file func and seq_file private data size.
Subsequent patches will have actual implementation
for bpf_map_ops->iter_seq_info.
In user space, BPF_ITER_LINK_MAP_FD needs to be
specified in prog attr->link_create.flags, which indicates
that attr->link_create.target_fd is a map_fd.
The reason for such an explicit flag is for possible
future cases where one bpf iterator may allow more than
one possible customization, e.g., pid and cgroup id for
task_file.
Current kernel internal implementation only allows
the target to register at most one required bpf_iter_link_info.
To support the above case, optional bpf_iter_link_info's
are needed, the target can be extended to register such link
infos, and user provided link_info needs to match one of
target supported ones.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184112.590360-1-yhs@fb.com
Readonly and readwrite buffer register states
are introduced. Totally four states,
PTR_TO_RDONLY_BUF[_OR_NULL] and PTR_TO_RDWR_BUF[_OR_NULL]
are supported. As suggested by their respective
names, PTR_TO_RDONLY_BUF[_OR_NULL] are for
readonly buffers and PTR_TO_RDWR_BUF[_OR_NULL]
for read/write buffers.
These new register states will be used
by later bpf map element iterator.
New register states share some similarity to
PTR_TO_TP_BUFFER as it will calculate accessed buffer
size during verification time. The accessed buffer
size will be later compared to other metrics during
later attach/link_create time.
Similar to reg_state PTR_TO_BTF_ID_OR_NULL in bpf
iterator programs, PTR_TO_RDONLY_BUF_OR_NULL or
PTR_TO_RDWR_BUF_OR_NULL reg_types can be set at
prog->aux->bpf_ctx_arg_aux, and bpf verifier will
retrieve the values during btf_ctx_access().
Later bpf map element iterator implementation
will show how such information will be assigned
during target registeration time.
The verifier is also enhanced such that PTR_TO_RDONLY_BUF
can be passed to ARG_PTR_TO_MEM[_OR_NULL] helper argument, and
PTR_TO_RDWR_BUF can be passed to ARG_PTR_TO_MEM[_OR_NULL] or
ARG_PTR_TO_UNINIT_MEM.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184111.590274-1-yhs@fb.com
This patch refactored target bpf_iter_init_seq_priv_t callback
function to accept additional information. This will be needed
in later patches for map element targets since a particular
map should be passed to traverse elements for that particular
map. In the future, other information may be passed to target
as well, e.g., pid, cgroup id, etc. to customize the iterator.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184110.590156-1-yhs@fb.com
There is no functionality change for this patch.
Struct bpf_iter_reg is used to register a bpf_iter target,
which includes information for both prog_load, link_create
and seq_file creation.
This patch puts fields related seq_file creation into
a different structure. This will be useful for map
elements iterator where one iterator covers different
map types and different map types may have different
seq_ops, init/fini private_data function and
private_data size.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184109.590030-1-yhs@fb.com
It's mostly a copy paste of commit 6086d29def ("bpf: Add bpf_map iterator")
that is use to implement bpf_seq_file opreations to traverse all bpf programs.
v1->v2: Tweak to use build time btf_id
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, the pos pointer in bpf iterator map/task/task_file
seq_ops->start() is always incremented.
This is incorrect. It should be increased only if
*pos is 0 (for SEQ_START_TOKEN) since these start()
function actually returns the first real object.
If *pos is not 0, it merely found the object
based on the state in seq->private, and not really
advancing the *pos. This patch fixed this issue
by only incrementing *pos if it is 0.
Note that the old *pos calculation, although not
correct, does not affect correctness of bpf_iter
as bpf_iter seq_file->read() does not support llseek.
This patch also renamed "mid" in bpf_map iterator
seq_file private data to "map_id" for better clarity.
Fixes: 6086d29def ("bpf: Add bpf_map iterator")
Fixes: eaaacd2391 ("bpf: Add task and task/file iterator targets")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722195156.4029817-1-yhs@fb.com
One additional field btf_id is added to struct
bpf_ctx_arg_aux to store the precomputed btf_ids.
The btf_id is computed at build time with
BTF_ID_LIST or BTF_ID_LIST_GLOBAL macro definitions.
All existing bpf iterators are changed to used
pre-compute btf_ids.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163403.1393551-1-yhs@fb.com
Currently, socket types (struct tcp_sock, udp_sock, etc.)
used by bpf_skc_to_*() helpers are computed when vmlinux_btf
is first built in the kernel.
Commit 5a2798ab32
("bpf: Add BTF_ID_LIST/BTF_ID/BTF_ID_UNUSED macros")
implemented a mechanism to compute btf_ids at kernel build
time which can simplify kernel implementation and reduce
runtime overhead by removing in-kernel btf_id calculation.
This patch did exactly this, removing in-kernel btf_id
computation and utilizing build-time btf_id computation.
If CONFIG_DEBUG_INFO_BTF is not defined, BTF_ID_LIST will
define an array with size of 5, which is not enough for
btf_sock_ids. So define its own static array if
CONFIG_DEBUG_INFO_BTF is not defined.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163358.1393023-1-yhs@fb.com
When CONFIG_NET is set but CONFIG_INET isn't, build fails with:
ld: kernel/bpf/net_namespace.o: in function `netns_bpf_attach_type_unneed':
kernel/bpf/net_namespace.c:32: undefined reference to `bpf_sk_lookup_enabled'
ld: kernel/bpf/net_namespace.o: in function `netns_bpf_attach_type_need':
kernel/bpf/net_namespace.c:43: undefined reference to `bpf_sk_lookup_enabled'
This is because without CONFIG_INET bpf_sk_lookup_enabled symbol is not
available. Wrap references to bpf_sk_lookup_enabled with preprocessor
conditionals.
Fixes: 1559b4aa1d ("inet: Run SK_LOOKUP BPF program on socket lookup")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/bpf/20200721100716.720477-1-jakub@cloudflare.com
Run a BPF program before looking up a listening socket on the receive path.
Program selects a listening socket to yield as result of socket lookup by
calling bpf_sk_assign() helper and returning SK_PASS code. Program can
revert its decision by assigning a NULL socket with bpf_sk_assign().
Alternatively, BPF program can also fail the lookup by returning with
SK_DROP, or let the lookup continue as usual with SK_PASS on return, when
no socket has been selected with bpf_sk_assign().
This lets the user match packets with listening sockets freely at the last
possible point on the receive path, where we know that packets are destined
for local delivery after undergoing policing, filtering, and routing.
With BPF code selecting the socket, directing packets destined to an IP
range or to a port range to a single socket becomes possible.
In case multiple programs are attached, they are run in series in the order
in which they were attached. The end result is determined from return codes
of all the programs according to following rules:
1. If any program returned SK_PASS and selected a valid socket, the socket
is used as result of socket lookup.
2. If more than one program returned SK_PASS and selected a socket,
last selection takes effect.
3. If any program returned SK_DROP, and no program returned SK_PASS and
selected a socket, socket lookup fails with -ECONNREFUSED.
4. If all programs returned SK_PASS and none of them selected a socket,
socket lookup continues to htable-based lookup.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-5-jakub@cloudflare.com
Add a new program type BPF_PROG_TYPE_SK_LOOKUP with a dedicated attach type
BPF_SK_LOOKUP. The new program kind is to be invoked by the transport layer
when looking up a listening socket for a new connection request for
connection oriented protocols, or when looking up an unconnected socket for
a packet for connection-less protocols.
When called, SK_LOOKUP BPF program can select a socket that will receive
the packet. This serves as a mechanism to overcome the limits of what
bind() API allows to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, on fixed port to a socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, on any port to a socket
198.51.100.1, any port -> L7 proxy socket
In its run-time context program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple. Context can be further extended to include ingress
interface identifier.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, and calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection. Transport layer then uses the selected
socket as a result of socket lookup.
In its basic form, SK_LOOKUP acts as a filter and hence must return either
SK_PASS or SK_DROP. If the program returns with SK_PASS, transport should
look for a socket to receive the packet, or use the one selected by the
program if available, while SK_DROP informs the transport layer that the
lookup should fail.
This patch only enables the user to attach an SK_LOOKUP program to a
network namespace. Subsequent patches hook it up to run on local delivery
path in ipv4 and ipv6 stacks.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-3-jakub@cloudflare.com
Extend the BPF netns link callbacks to rebuild (grow/shrink) or update the
prog_array at given position when link gets attached/updated/released.
This let's us lift the limit of having just one link attached for the new
attach type introduced by subsequent patch.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-2-jakub@cloudflare.com
Introduce XDP_REDIRECT support for eBPF programs attached to cpumap
entries.
This patch has been tested on Marvell ESPRESSObin using a modified
version of xdp_redirect_cpu sample in order to attach a XDP program
to CPUMAP entries to perform a redirect on the mvneta interface.
In particular the following scenario has been tested:
rq (cpu0) --> mvneta - XDP_REDIRECT (cpu0) --> CPUMAP - XDP_REDIRECT (cpu1) --> mvneta
$./xdp_redirect_cpu -p xdp_cpu_map0 -d eth0 -c 1 -e xdp_redirect \
-f xdp_redirect_kern.o -m tx_port -r eth0
tx: 285.2 Kpps rx: 285.2 Kpps
Attaching a simple XDP program on eth0 to perform XDP_TX gives
comparable results:
tx: 288.4 Kpps rx: 288.4 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/2cf8373a731867af302b00c4ff16c122630c4980.1594734381.git.lorenzo@kernel.org
Introduce the capability to attach an eBPF program to cpumap entries.
The idea behind this feature is to add the possibility to define on
which CPU run the eBPF program if the underlying hw does not support
RSS. Current supported verdicts are XDP_DROP and XDP_PASS.
This patch has been tested on Marvell ESPRESSObin using xdp_redirect_cpu
sample available in the kernel tree to identify possible performance
regressions. Results show there are no observable differences in
packet-per-second:
$./xdp_redirect_cpu --progname xdp_cpu_map0 --dev eth0 --cpu 1
rx: 354.8 Kpps
rx: 356.0 Kpps
rx: 356.8 Kpps
rx: 356.3 Kpps
rx: 356.6 Kpps
rx: 356.6 Kpps
rx: 356.7 Kpps
rx: 355.8 Kpps
rx: 356.8 Kpps
rx: 356.8 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/5c9febdf903d810b3415732e5cd98491d7d9067a.1594734381.git.lorenzo@kernel.org
As it has been already done for devmap, introduce 'struct bpf_cpumap_val'
to formalize the expected values that can be passed in for a CPUMAP.
Update cpumap code to use the struct.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/754f950674665dae6139c061d28c1d982aaf4170.1594734381.git.lorenzo@kernel.org
Commit 77361825bb ("bpf: cpumap use ptr_ring_consume_batched") changed
away from using single frame ptr_ring dequeue (__ptr_ring_consume) to
consume a batched, but it uses a locked version, which as the comment
explain isn't needed.
Change to use the non-locked version __ptr_ring_consume_batched.
Fixes: 77361825bb ("bpf: cpumap use ptr_ring_consume_batched")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/a9c7d06f9a009e282209f0c8c7b2c5d9b9ad60b9.1594734381.git.lorenzo@kernel.org
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the ID is resolved during compile time,
and we can remove the runtime name search.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200711215329.41165-7-jolsa@kernel.org
Now when we moved the helpers btf_id arrays into .BTF_ids section,
we can remove the code that resolve those IDs in runtime.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200711215329.41165-6-jolsa@kernel.org
Using BTF_ID_LIST macro to define lists for several helpers
using BTF arguments.
And running resolve_btfids on vmlinux elf object during linking,
so the .BTF_ids section gets the IDs resolved.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200711215329.41165-5-jolsa@kernel.org
Pull networking fixes from David Miller:
1) Restore previous behavior of CAP_SYS_ADMIN wrt loading networking
BPF programs, from Maciej Żenczykowski.
2) Fix dropped broadcasts in mac80211 code, from Seevalamuthu
Mariappan.
3) Slay memory leak in nl80211 bss color attribute parsing code, from
Luca Coelho.
4) Get route from skb properly in ip_route_use_hint(), from Miaohe Lin.
5) Don't allow anything other than ARPHRD_ETHER in llc code, from Eric
Dumazet.
6) xsk code dips too deeply into DMA mapping implementation internals.
Add dma_need_sync and use it. From Christoph Hellwig
7) Enforce power-of-2 for BPF ringbuf sizes. From Andrii Nakryiko.
8) Check for disallowed attributes when loading flow dissector BPF
programs. From Lorenz Bauer.
9) Correct packet injection to L3 tunnel devices via AF_PACKET, from
Jason A. Donenfeld.
10) Don't advertise checksum offload on ipa devices that don't support
it. From Alex Elder.
11) Resolve several issues in TCP MD5 signature support. Missing memory
barriers, bogus options emitted when using syncookies, and failure
to allow md5 key changes in established states. All from Eric
Dumazet.
12) Fix interface leak in hsr code, from Taehee Yoo.
13) VF reset fixes in hns3 driver, from Huazhong Tan.
14) Make loopback work again with ipv6 anycast, from David Ahern.
15) Fix TX starvation under high load in fec driver, from Tobias
Waldekranz.
16) MLD2 payload lengths not checked properly in bridge multicast code,
from Linus Lüssing.
17) Packet scheduler code that wants to find the inner protocol
currently only works for one level of VLAN encapsulation. Allow
Q-in-Q situations to work properly here, from Toke
Høiland-Jørgensen.
18) Fix route leak in l2tp, from Xin Long.
19) Resolve conflict between the sk->sk_user_data usage of bpf reuseport
support and various protocols. From Martin KaFai Lau.
20) Fix socket cgroup v2 reference counting in some situations, from
Cong Wang.
21) Cure memory leak in mlx5 connection tracking offload support, from
Eli Britstein.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
mlxsw: pci: Fix use-after-free in case of failed devlink reload
mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()
net: macb: fix call to pm_runtime in the suspend/resume functions
net: macb: fix macb_suspend() by removing call to netif_carrier_off()
net: macb: fix macb_get/set_wol() when moving to phylink
net: macb: mark device wake capable when "magic-packet" property present
net: macb: fix wakeup test in runtime suspend/resume routines
bnxt_en: fix NULL dereference in case SR-IOV configuration fails
libbpf: Fix libbpf hashmap on (I)LP32 architectures
net/mlx5e: CT: Fix memory leak in cleanup
net/mlx5e: Fix port buffers cell size value
net/mlx5e: Fix 50G per lane indication
net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash
net/mlx5e: Fix VXLAN configuration restore after function reload
net/mlx5e: Fix usage of rcu-protected pointer
net/mxl5e: Verify that rpriv is not NULL
net/mlx5: E-Switch, Fix vlan or qos setting in legacy mode
net/mlx5: Fix eeprom support for SFP module
cgroup: Fix sock_cgroup_data on big-endian.
selftests: bpf: Fix detach from sockmap tests
...
Several users of kallsyms_show_value() were performing checks not
during "open". Refactor everything needed to gain proper checks against
file->f_cred for modules, kprobes, and bpf.
-----BEGIN PGP SIGNATURE-----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=ib5Q
-----END PGP SIGNATURE-----
Merge tag 'kallsyms_show_value-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kallsyms fix from Kees Cook:
"Refactor kallsyms_show_value() users for correct cred.
I'm not delighted by the timing of getting these changes to you, but
it does fix a handful of kernel address exposures, and no one has
screamed yet at the patches.
Several users of kallsyms_show_value() were performing checks not
during "open". Refactor everything needed to gain proper checks
against file->f_cred for modules, kprobes, and bpf"
* tag 'kallsyms_show_value-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
selftests: kmod: Add module address visibility test
bpf: Check correct cred for CAP_SYSLOG in bpf_dump_raw_ok()
kprobes: Do not expose probe addresses to non-CAP_SYSLOG
module: Do not expose section addresses to non-CAP_SYSLOG
module: Refactor section attr into bin attribute
kallsyms: Refactor kallsyms_show_value() to take cred
bpf_sk_reuseport_detach is currently called when sk->sk_user_data
is not NULL. It is incorrect because sk->sk_user_data may not be
managed by the bpf's reuseport_array. It has been reported in [1] that,
the bpf_sk_reuseport_detach() which is called from udp_lib_unhash() has
corrupted the sk_user_data managed by l2tp.
This patch solves it by using another bit (defined as SK_USER_DATA_BPF)
of the sk_user_data pointer value. It marks that a sk_user_data is
managed/owned by BPF.
The patch depends on a PTRMASK introduced in
commit f1ff5ce2cd ("net, sk_msg: Clear sk_user_data pointer on clone if tagged").
[ Note: sk->sk_user_data is used by bpf's reuseport_array only when a sk is
added to the bpf's reuseport_array.
i.e. doing setsockopt(SO_REUSEPORT) and having "sk->sk_reuseport == 1"
alone will not stop sk->sk_user_data being used by other means. ]
[1]: https://lore.kernel.org/netdev/20200706121259.GA20199@katalix.com/
Fixes: 5dc4c4b7d4 ("bpf: Introduce BPF_MAP_TYPE_REUSEPORT_SOCKARRAY")
Reported-by: James Chapman <jchapman@katalix.com>
Reported-by: syzbot+9f092552ba9a5efca5df@syzkaller.appspotmail.com
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: James Chapman <jchapman@katalix.com>
Acked-by: James Chapman <jchapman@katalix.com>
Link: https://lore.kernel.org/bpf/20200709061110.4019316-1-kafai@fb.com
It makes little sense for copying sk_user_data of reuseport_array during
sk_clone_lock(). This patch reuses the SK_USER_DATA_NOCOPY bit introduced in
commit f1ff5ce2cd ("net, sk_msg: Clear sk_user_data pointer on clone if tagged").
It is used to mark the sk_user_data is not supposed to be copied to its clone.
Although the cloned sk's sk_user_data will not be used/freed in
bpf_sk_reuseport_detach(), this change can still allow the cloned
sk's sk_user_data to be used by some other means.
Freeing the reuseport_array's sk_user_data does not require a rcu grace
period. Thus, the existing rcu_assign_sk_user_data_nocopy() is not
used.
Fixes: 5dc4c4b7d4 ("bpf: Introduce BPF_MAP_TYPE_REUSEPORT_SOCKARRAY")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200709061104.4018798-1-kafai@fb.com
When evaluating access control over kallsyms visibility, credentials at
open() time need to be used, not the "current" creds (though in BPF's
case, this has likely always been the same). Plumb access to associated
file->f_cred down through bpf_dump_raw_ok() and its callers now that
kallsysm_show_value() has been refactored to take struct cred.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: bpf@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 7105e828c0 ("bpf: allow for correlation of maps and helpers in dump")
Signed-off-by: Kees Cook <keescook@chromium.org>
Sometimes it's handy to know when the socket gets freed. In
particular, we'd like to try to use a smarter allocation of
ports for bpf_bind and explore the possibility of limiting
the number of SOCK_DGRAM sockets the process can have.
Implement BPF_CGROUP_INET_SOCK_RELEASE hook that triggers on
inet socket release. It triggers only for userspace sockets
(not in-kernel ones) and therefore has the same semantics as
the existing BPF_CGROUP_INET_SOCK_CREATE.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200706230128.4073544-2-sdf@google.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-07-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 17 day(s) which contain
a total of 106 files changed, 5233 insertions(+), 1283 deletions(-).
The main changes are:
1) bpftool ability to show PIDs of processes having open file descriptors
for BPF map/program/link/BTF objects, relying on BPF iterator progs
to extract this info efficiently, from Andrii Nakryiko.
2) Addition of BPF iterator progs for dumping TCP and UDP sockets to
seq_files, from Yonghong Song.
3) Support access to BPF map fields in struct bpf_map from programs
through BTF struct access, from Andrey Ignatov.
4) Add a bpf_get_task_stack() helper to be able to dump /proc/*/stack
via seq_file from BPF iterator progs, from Song Liu.
5) Make SO_KEEPALIVE and related options available to bpf_setsockopt()
helper, from Dmitry Yakunin.
6) Optimize BPF sk_storage selection of its caching index, from Martin
KaFai Lau.
7) Removal of redundant synchronize_rcu()s from BPF map destruction which
has been a historic leftover, from Alexei Starovoitov.
8) Several improvements to test_progs to make it easier to create a shell
loop that invokes each test individually which is useful for some CIs,
from Jesper Dangaard Brouer.
9) Fix bpftool prog dump segfault when compiled without skeleton code on
older clang versions, from John Fastabend.
10) Bunch of cleanups and minor improvements, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_STACKTRACE stack_trace_save_tsk() is not defined. Let
get_callchain_entry_for_task() to always return NULL in such cases.
Fixes: fa28dcb82a ("bpf: Introduce helper bpf_get_task_stack()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200703024537.79971-1-songliubraving@fb.com
Introduce helper bpf_get_task_stack(), which dumps stack trace of given
task. This is different to bpf_get_stack(), which gets stack track of
current task. One potential use case of bpf_get_task_stack() is to call
it from bpf_iter__task and dump all /proc/<pid>/stack to a seq_file.
bpf_get_task_stack() uses stack_trace_save_tsk() instead of
get_perf_callchain() for kernel stack. The benefit of this choice is that
stack_trace_save_tsk() doesn't require changes in arch/. The downside of
using stack_trace_save_tsk() is that stack_trace_save_tsk() dumps the
stack trace to unsigned long array. For 32-bit systems, we need to
translate it to u64 array.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200630062846.664389-3-songliubraving@fb.com
bpf_free_used_maps() or close(map_fd) will trigger map_free callback.
bpf_free_used_maps() is called after bpf prog is no longer executing:
bpf_prog_put->call_rcu->bpf_prog_free->bpf_free_used_maps.
Hence there is no need to call synchronize_rcu() to protect map elements.
Note that hash_of_maps and array_of_maps update/delete inner maps via
sys_bpf() that calls maybe_wait_bpf_programs() and synchronize_rcu().
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/bpf/20200630043343.53195-2-alexei.starovoitov@gmail.com
Wenbo reported an issue in [1] where a checking of null
pointer is evaluated as always false. In this particular
case, the program type is tp_btf and the pointer to
compare is a PTR_TO_BTF_ID.
The current verifier considers PTR_TO_BTF_ID always
reprents a non-null pointer, hence all PTR_TO_BTF_ID compares
to 0 will be evaluated as always not-equal, which resulted
in the branch elimination.
For example,
struct bpf_fentry_test_t {
struct bpf_fentry_test_t *a;
};
int BPF_PROG(test7, struct bpf_fentry_test_t *arg)
{
if (arg == 0)
test7_result = 1;
return 0;
}
int BPF_PROG(test8, struct bpf_fentry_test_t *arg)
{
if (arg->a == 0)
test8_result = 1;
return 0;
}
In above bpf programs, both branch arg == 0 and arg->a == 0
are removed. This may not be what developer expected.
The bug is introduced by Commit cac616db39 ("bpf: Verifier
track null pointer branch_taken with JNE and JEQ"),
where PTR_TO_BTF_ID is considered to be non-null when evaluting
pointer vs. scalar comparison. This may be added
considering we have PTR_TO_BTF_ID_OR_NULL in the verifier
as well.
PTR_TO_BTF_ID_OR_NULL is added to explicitly requires
a non-NULL testing in selective cases. The current generic
pointer tracing framework in verifier always
assigns PTR_TO_BTF_ID so users does not need to
check NULL pointer at every pointer level like a->b->c->d.
We may not want to assign every PTR_TO_BTF_ID as
PTR_TO_BTF_ID_OR_NULL as this will require a null test
before pointer dereference which may cause inconvenience
for developers. But we could avoid branch elimination
to preserve original code intention.
This patch simply removed PTR_TO_BTD_ID from reg_type_not_null()
in verifier, which prevented the above branches from being eliminated.
[1]: https://lore.kernel.org/bpf/79dbb7c0-449d-83eb-5f4f-7af0cc269168@fb.com/T/
Fixes: cac616db39 ("bpf: Verifier track null pointer branch_taken with JNE and JEQ")
Reported-by: Wenbo Zhang <ethercflow@gmail.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200630171240.2523722-1-yhs@fb.com
Iterating over BPF links attached to network namespace in pre_exit hook is
not safe, even if there is just one. Once link gets auto-detached, that is
its back-pointer to net object is set to NULL, the link can be released and
freed without waiting on netns_bpf_mutex, effectively causing the list
element we are operating on to be freed.
This leads to use-after-free when trying to access the next element on the
list, as reported by KASAN. Bug can be triggered by destroying a network
namespace, while also releasing a link attached to this network namespace.
| ==================================================================
| BUG: KASAN: use-after-free in netns_bpf_pernet_pre_exit+0xd9/0x130
| Read of size 8 at addr ffff888119e0d778 by task kworker/u8:2/177
|
| CPU: 3 PID: 177 Comm: kworker/u8:2 Not tainted 5.8.0-rc1-00197-ga0c04c9d1008-dirty #776
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190727_073836-buildvm-ppc64le-16.ppc.fedoraproject.org-3.fc31 04/01/2014
| Workqueue: netns cleanup_net
| Call Trace:
| dump_stack+0x9e/0xe0
| print_address_description.constprop.0+0x3a/0x60
| ? netns_bpf_pernet_pre_exit+0xd9/0x130
| kasan_report.cold+0x1f/0x40
| ? netns_bpf_pernet_pre_exit+0xd9/0x130
| netns_bpf_pernet_pre_exit+0xd9/0x130
| cleanup_net+0x30b/0x5b0
| ? unregister_pernet_device+0x50/0x50
| ? rcu_read_lock_bh_held+0xb0/0xb0
| ? _raw_spin_unlock_irq+0x24/0x50
| process_one_work+0x4d1/0xa10
| ? lock_release+0x3e0/0x3e0
| ? pwq_dec_nr_in_flight+0x110/0x110
| ? rwlock_bug.part.0+0x60/0x60
| worker_thread+0x7a/0x5c0
| ? process_one_work+0xa10/0xa10
| kthread+0x1e3/0x240
| ? kthread_create_on_node+0xd0/0xd0
| ret_from_fork+0x1f/0x30
|
| Allocated by task 280:
| save_stack+0x1b/0x40
| __kasan_kmalloc.constprop.0+0xc2/0xd0
| netns_bpf_link_create+0xfe/0x650
| __do_sys_bpf+0x153a/0x2a50
| do_syscall_64+0x59/0x300
| entry_SYSCALL_64_after_hwframe+0x44/0xa9
|
| Freed by task 198:
| save_stack+0x1b/0x40
| __kasan_slab_free+0x12f/0x180
| kfree+0xed/0x350
| process_one_work+0x4d1/0xa10
| worker_thread+0x7a/0x5c0
| kthread+0x1e3/0x240
| ret_from_fork+0x1f/0x30
|
| The buggy address belongs to the object at ffff888119e0d700
| which belongs to the cache kmalloc-192 of size 192
| The buggy address is located 120 bytes inside of
| 192-byte region [ffff888119e0d700, ffff888119e0d7c0)
| The buggy address belongs to the page:
| page:ffffea0004678340 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0
| flags: 0x2fffe0000000200(slab)
| raw: 02fffe0000000200 ffffea00045ba8c0 0000000600000006 ffff88811a80ea80
| raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
| page dumped because: kasan: bad access detected
|
| Memory state around the buggy address:
| ffff888119e0d600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
| ffff888119e0d680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
| >ffff888119e0d700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
| ^
| ffff888119e0d780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
| ffff888119e0d800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
| ==================================================================
Remove the "fast-path" for releasing a link that got auto-detached by a
dying network namespace to fix it. This way as long as link is on the list
and netns_bpf mutex is held, we have a guarantee that link memory can be
accessed.
An alternative way to fix this issue would be to safely iterate over the
list of links and ensure there is no access to link object after detaching
it. But, at the moment, optimizing synchronization overhead on link release
without a workload in mind seems like an overkill.
Fixes: ab53cad90e ("bpf, netns: Keep a list of attached bpf_link's")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200630164541.1329993-1-jakub@cloudflare.com
The sockmap code currently ignores the value of attach_bpf_fd when
detaching a program. This is contrary to the usual behaviour of
checking that attach_bpf_fd represents the currently attached
program.
Ensure that attach_bpf_fd is indeed the currently attached
program. It turns out that all sockmap selftests already do this,
which indicates that this is unlikely to cause breakage.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200629095630.7933-5-lmb@cloudflare.com
Using BPF_PROG_DETACH on a flow dissector program supports neither
attach_flags nor attach_bpf_fd. Yet no value is enforced for them.
Enforce that attach_flags are zero, and require the current program
to be passed via attach_bpf_fd. This allows us to remove the check
for CAP_SYS_ADMIN, since userspace can now no longer remove
arbitrary flow dissector programs.
Fixes: b27f7bb590 ("flow_dissector: Move out netns_bpf prog callbacks")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200629095630.7933-3-lmb@cloudflare.com
Using BPF_PROG_ATTACH on a flow dissector program supports neither
target_fd, attach_flags or replace_bpf_fd but accepts any value.
Enforce that all of them are zero. This is fine for replace_bpf_fd
since its presence is indicated by BPF_F_REPLACE. It's more
problematic for target_fd, since zero is a valid fd. Should we
want to use the flag later on we'd have to add an exception for
fd 0. The alternative is to force a value like -1. This requires
more changes to tests. There is also precedent for using 0,
since bpf_iter uses this for target_fd as well.
Fixes: b27f7bb590 ("flow_dissector: Move out netns_bpf prog callbacks")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200629095630.7933-2-lmb@cloudflare.com
To support multi-prog link-based attachments for new netns attach types, we
need to keep track of more than one bpf_link per attach type. Hence,
convert net->bpf.links into a list, that currently can be either empty or
have just one item.
Instead of reusing bpf_prog_list from bpf-cgroup, we link together
bpf_netns_link's themselves. This makes list management simpler as we don't
have to allocate, initialize, and later release list elements. We can do
this because multi-prog attachment will be available only for bpf_link, and
we don't need to build a list of programs attached directly and indirectly
via links.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-4-jakub@cloudflare.com
Prepare for having multi-prog attachments for new netns attach types by
storing programs to run in a bpf_prog_array, which is well suited for
iterating over programs and running them in sequence.
After this change bpf(PROG_QUERY) may block to allocate memory in
bpf_prog_array_copy_to_user() for collected program IDs. This forces a
change in how we protect access to the attached program in the query
callback. Because bpf_prog_array_copy_to_user() can sleep, we switch from
an RCU read lock to holding a mutex that serializes updaters.
Because we allow only one BPF flow_dissector program to be attached to
netns at all times, the bpf_prog_array pointed by net->bpf.run_array is
always either detached (null) or one element long.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-3-jakub@cloudflare.com
Prepare for using bpf_prog_array to store attached programs by moving out
code that updates the attached program out of flow dissector.
Managing bpf_prog_array is more involved than updating a single bpf_prog
pointer. This will let us do it all from one place, bpf/net_namespace.c, in
the subsequent patch.
No functional change intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-2-jakub@cloudflare.com
BPF ringbuf assumes the size to be a multiple of page size and the power of
2 value. The latter is important to avoid division while calculating position
inside the ring buffer and using (N-1) mask instead. This patch fixes omission
to enforce power-of-2 size rule.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200630061500.1804799-1-andriin@fb.com
To ensure btf_ctx_access() is safe the verifier checks that the BTF
arg type is an int, enum, or pointer. When the function does the
BTF arg lookup it uses the calculation 'arg = off / 8' using the
fact that registers are 8B. This requires that the first arg is
in the first reg, the second in the second, and so on. However,
for __int128 the arg will consume two registers by default LLVM
implementation. So this will cause the arg layout assumed by the
'arg = off / 8' calculation to be incorrect.
Because __int128 is uncommon this patch applies the easiest fix and
will force int types to be sizeof(u64) or smaller so that they will
fit in a single register.
v2: remove unneeded parens per Andrii's feedback
Fixes: 9e15db6613 ("bpf: Implement accurate raw_tp context access via BTF")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/159303723962.11287.13309537171132420717.stgit@john-Precision-5820-Tower
The helper is used in tracing programs to cast a socket
pointer to a tcp6_sock pointer.
The return value could be NULL if the casting is illegal.
A new helper return type RET_PTR_TO_BTF_ID_OR_NULL is added
so the verifier is able to deduce proper return types for the helper.
Different from the previous BTF_ID based helpers,
the bpf_skc_to_tcp6_sock() argument can be several possible
btf_ids. More specifically, all possible socket data structures
with sock_common appearing in the first in the memory layout.
This patch only added socket types related to tcp and udp.
All possible argument btf_id and return value btf_id
for helper bpf_skc_to_tcp6_sock() are pre-calculcated and
cached. In the future, it is even possible to precompute
these btf_id's at kernel build time.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200623230809.3988195-1-yhs@fb.com
This is a fix for a regression in commit 2c78ee898d ("bpf: Implement CAP_BPF").
Before the above commit it was possible to load network bpf programs
with just the CAP_SYS_ADMIN privilege.
The Android bpfloader happens to run in such a configuration (it has
SYS_ADMIN but not NET_ADMIN) and creates maps and loads bpf programs
for later use by Android's netd (which has NET_ADMIN but not SYS_ADMIN).
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/bpf/20200620212616.93894-1-zenczykowski@gmail.com
Currently, if a bpf program has more than one subprograms, each program will be
jitted separately. For programs with bpf-to-bpf calls the
prog->aux->num_exentries is not setup properly. For example, with
bpf_iter_netlink.c modified to force one function to be not inlined and with
CONFIG_BPF_JIT_ALWAYS_ON the following error is seen:
$ ./test_progs -n 3/3
...
libbpf: failed to load program 'iter/netlink'
libbpf: failed to load object 'bpf_iter_netlink'
libbpf: failed to load BPF skeleton 'bpf_iter_netlink': -4007
test_netlink:FAIL:bpf_iter_netlink__open_and_load skeleton open_and_load failed
#3/3 netlink:FAIL
The dmesg shows the following errors:
ex gen bug
which is triggered by the following code in arch/x86/net/bpf_jit_comp.c:
if (excnt >= bpf_prog->aux->num_exentries) {
pr_err("ex gen bug\n");
return -EFAULT;
}
This patch fixes the issue by computing proper num_exentries for each
subprogram before calling JIT.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Set map_btf_name and map_btf_id for all map types so that map fields can
be accessed by bpf programs.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/a825f808f22af52b018dbe82f1c7d29dab5fc978.1592600985.git.rdna@fb.com
There are multiple use-cases when it's convenient to have access to bpf
map fields, both `struct bpf_map` and map type specific struct-s such as
`struct bpf_array`, `struct bpf_htab`, etc.
For example while working with sock arrays it can be necessary to
calculate the key based on map->max_entries (some_hash % max_entries).
Currently this is solved by communicating max_entries via "out-of-band"
channel, e.g. via additional map with known key to get info about target
map. That works, but is not very convenient and error-prone while
working with many maps.
In other cases necessary data is dynamic (i.e. unknown at loading time)
and it's impossible to get it at all. For example while working with a
hash table it can be convenient to know how much capacity is already
used (bpf_htab.count.counter for BPF_F_NO_PREALLOC case).
At the same time kernel knows this info and can provide it to bpf
program.
Fill this gap by adding support to access bpf map fields from bpf
program for both `struct bpf_map` and map type specific fields.
Support is implemented via btf_struct_access() so that a user can define
their own `struct bpf_map` or map type specific struct in their program
with only necessary fields and preserve_access_index attribute, cast a
map to this struct and use a field.
For example:
struct bpf_map {
__u32 max_entries;
} __attribute__((preserve_access_index));
struct bpf_array {
struct bpf_map map;
__u32 elem_size;
} __attribute__((preserve_access_index));
struct {
__uint(type, BPF_MAP_TYPE_ARRAY);
__uint(max_entries, 4);
__type(key, __u32);
__type(value, __u32);
} m_array SEC(".maps");
SEC("cgroup_skb/egress")
int cg_skb(void *ctx)
{
struct bpf_array *array = (struct bpf_array *)&m_array;
struct bpf_map *map = (struct bpf_map *)&m_array;
/* .. use map->max_entries or array->map.max_entries .. */
}
Similarly to other btf_struct_access() use-cases (e.g. struct tcp_sock
in net/ipv4/bpf_tcp_ca.c) the patch allows access to any fields of
corresponding struct. Only reading from map fields is supported.
For btf_struct_access() to work there should be a way to know btf id of
a struct that corresponds to a map type. To get btf id there should be a
way to get a stringified name of map-specific struct, such as
"bpf_array", "bpf_htab", etc for a map type. Two new fields are added to
`struct bpf_map_ops` to handle it:
* .map_btf_name keeps a btf name of a struct returned by map_alloc();
* .map_btf_id is used to cache btf id of that struct.
To make btf ids calculation cheaper they're calculated once while
preparing btf_vmlinux and cached same way as it's done for btf_id field
of `struct bpf_func_proto`
While calculating btf ids, struct names are NOT checked for collision.
Collisions will be checked as a part of the work to prepare btf ids used
in verifier in compile time that should land soon. The only known
collision for `struct bpf_htab` (kernel/bpf/hashtab.c vs
net/core/sock_map.c) was fixed earlier.
Both new fields .map_btf_name and .map_btf_id must be set for a map type
for the feature to work. If neither is set for a map type, verifier will
return ENOTSUPP on a try to access map_ptr of corresponding type. If
just one of them set, it's verifier misconfiguration.
Only `struct bpf_array` for BPF_MAP_TYPE_ARRAY and `struct bpf_htab` for
BPF_MAP_TYPE_HASH are supported by this patch. Other map types will be
supported separately.
The feature is available only for CONFIG_DEBUG_INFO_BTF=y and gated by
perfmon_capable() so that unpriv programs won't have access to bpf map
fields.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/6479686a0cd1e9067993df57b4c3eef0e276fec9.1592600985.git.rdna@fb.com
btf_parse_vmlinux() implements manual search for struct bpf_ctx_convert
since at the time of implementing btf_find_by_name_kind() was not
available.
Later btf_find_by_name_kind() was introduced in 27ae7997a6 ("bpf:
Introduce BPF_PROG_TYPE_STRUCT_OPS"). It provides similar search
functionality and can be leveraged in btf_parse_vmlinux(). Do it.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/6e12d5c3e8a3d552925913ef73a695dd1bb27800.1592600985.git.rdna@fb.com
When do experiments with llvm (disabling instcombine and
simplifyCFG), I hit the following error with test_seg6_loop.o.
; R1=pkt(id=0,off=0,r=48,imm=0), R7=pkt(id=0,off=40,r=48,imm=0)
w2 = w7
; R2_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff))
w2 -= w1
R2 32-bit pointer arithmetic prohibited
The corresponding source code is:
uint32_t srh_off
// srh and skb->data are all packet pointers
srh_off = (char *)srh - (char *)(long)skb->data;
The verifier does not support 32-bit pointer/scalar arithmetic.
Without my llvm change, the code looks like
; R3=pkt(id=0,off=40,r=48,imm=0), R8=pkt(id=0,off=0,r=48,imm=0)
w3 -= w8
; R3_w=inv(id=0)
This is explicitly allowed in verifier if both registers are
pointers and the opcode is BPF_SUB.
To fix this problem, I changed the verifier to allow
32-bit pointer/scaler BPF_SUB operations.
At the source level, the issue could be workarounded with
inline asm or changing "uint32_t srh_off" to "uint64_t srh_off".
But I feel that verifier change might be the right thing to do.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200618234631.3321118-1-yhs@fb.com
Attaching to these hooks can break iptables because its optval is
usually quite big, or at least bigger than the current PAGE_SIZE limit.
David also mentioned some SCTP options can be big (around 256k).
For such optvals we expose only the first PAGE_SIZE bytes to
the BPF program. BPF program has two options:
1. Set ctx->optlen to 0 to indicate that the BPF's optval
should be ignored and the kernel should use original userspace
value.
2. Set ctx->optlen to something that's smaller than the PAGE_SIZE.
v5:
* use ctx->optlen == 0 with trimmed buffer (Alexei Starovoitov)
* update the docs accordingly
v4:
* use temporary buffer to avoid optval == optval_end == NULL;
this removes the corner case in the verifier that might assume
non-zero PTR_TO_PACKET/PTR_TO_PACKET_END.
v3:
* don't increase the limit, bypass the argument
v2:
* proper comments formatting (Jakub Kicinski)
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Link: https://lore.kernel.org/bpf/20200617010416.93086-1-sdf@google.com
Syzkaller discovered that creating a hash of type devmap_hash with a large
number of entries can hit the memory allocator limit for allocating
contiguous memory regions. There's really no reason to use kmalloc_array()
directly in the devmap code, so just switch it to the existing
bpf_map_area_alloc() function that is used elsewhere.
Fixes: 6f9d451ab1 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200616142829.114173-1-toke@redhat.com
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
BPF_PROBE_MEM is kernel-internal implmementation details. When dumping BPF
instructions to user-space, it needs to be replaced back with BPF_MEM mode.
Fixes: 2a02759ef5 ("bpf: Add support for BTF pointers to interpreter")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200613002115.1632142-1-andriin@fb.com
Pull misc uaccess updates from Al Viro:
"Assorted uaccess patches for this cycle - the stuff that didn't fit
into thematic series"
* 'uaccess.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
bpf: make bpf_check_uarg_tail_zero() use check_zeroed_user()
x86: kvm_hv_set_msr(): use __put_user() instead of 32bit __clear_user()
user_regset_copyout_zero(): use clear_user()
TEST_ACCESS_OK _never_ had been checked anywhere
x86: switch cp_stat64() to unsafe_put_user()
binfmt_flat: don't use __put_user()
binfmt_elf_fdpic: don't use __... uaccess primitives
binfmt_elf: don't bother with __{put,copy_to}_user()
pselect6() and friends: take handling the combined 6th/7th args into helper
V2:
- Defer changing BPF-syscall to start at file-descriptor 1
- Use {} to zero initialise struct.
The recent commit fbee97feed ("bpf: Add support to attach bpf program to a
devmap entry"), introduced ability to attach (and run) a separate XDP
bpf_prog for each devmap entry. A bpf_prog is added via a file-descriptor.
As zero were a valid FD, not using the feature requires using value minus-1.
The UAPI is extended via tail-extending struct bpf_devmap_val and using
map->value_size to determine the feature set.
This will break older userspace applications not using the bpf_prog feature.
Consider an old userspace app that is compiled against newer kernel
uapi/bpf.h, it will not know that it need to initialise the member
bpf_prog.fd to minus-1. Thus, users will be forced to update source code to
get program running on newer kernels.
This patch remove the minus-1 checks, and have zero mean feature isn't used.
Followup patches either for kernel or libbpf should handle and avoid
returning file-descriptor zero in the first place.
Fixes: fbee97feed ("bpf: Add support to attach bpf program to a devmap entry")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159170950687.2102545.7235914718298050113.stgit@firesoul
When using BPF_PROG_ATTACH to attach a program to a cgroup in
BPF_F_ALLOW_MULTI mode, it is not possible to replace a program
with itself. This is because the check for duplicate programs
doesn't take the replacement program into account.
Replacing a program with itself might seem weird, but it has
some uses: first, it allows resetting the associated cgroup storage.
Second, it makes the API consistent with the non-ALLOW_MULTI usage,
where it is possible to replace a program with itself. Third, it
aligns BPF_PROG_ATTACH with bpf_link, where replacing itself is
also supported.
Sice this code has been refactored a few times this change will
only apply to v5.7 and later. Adjustments could be made to
commit 1020c1f24a ("bpf: Simplify __cgroup_bpf_attach") and
commit d7bf2c10af ("bpf: allocate cgroup storage entries on attaching bpf programs")
as well as commit 324bda9e6c ("bpf: multi program support for cgroup+bpf")
Fixes: af6eea5743 ("bpf: Implement bpf_link-based cgroup BPF program attachment")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200608162202.94002-1-lmb@cloudflare.com
This is a new context that does not handle metadata at the moment, so
mark data_meta invalid.
Fixes: fbee97feed ("bpf: Add support to attach bpf program to a devmap entry")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200608151723.9539-1-dsahern@kernel.org
Add a couple APIs used by kernel/bpf/stackmap.c only:
- mmap_read_trylock_non_owner()
- mmap_read_unlock_non_owner() (may be called from a work queue).
It's still not ideal that bpf/stackmap subverts the lock ownership in this
way. Thanks to Peter Zijlstra for suggesting this API as the least-ugly
way of addressing this in the short term.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ying Han <yinghan@google.com>
Link: http://lkml.kernel.org/r/20200520052908.204642-8-walken@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code returns success if the "info_aux" allocation fails but it
should return -ENOMEM.
Fixes: 8c1b6e69dc ("bpf: Compare BTF types of functions arguments with actual types")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200604085436.GA943001@mwanda
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Open code it in __bpf_map_area_alloc, which is the only caller. Also
clean up __bpf_map_area_alloc to have a single vmalloc call with slightly
different flags instead of the current two different calls.
For this to compile for the nommu case add a __vmalloc_node_range stub to
nommu.c.
[akpm@linux-foundation.org: fix nommu.c build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20200414131348.444715-27-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just use __vmalloc_node instead which gets and extra argument. To be able
to to use __vmalloc_node in all caller make it available outside of
vmalloc and implement it in nommu.c.
[akpm@linux-foundation.org: fix nommu build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20200414131348.444715-25-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Failure to update a bpf_link because it has been auto-detached by a dying
cgroup currently results in EINVAL error, even though the arguments passed
to bpf() syscall are not wrong.
bpf_links attaching to netns in this case will return ENOLINK, which
carries the message that the link is no longer attached to anything.
Change cgroup bpf_links to do the same to keep the uAPI errors consistent.
Fixes: 0c991ebc8c ("bpf: Implement bpf_prog replacement for an active bpf_cgroup_link")
Suggested-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-6-jakub@cloudflare.com
Extend bpf() syscall subcommands that operate on bpf_link, that is
LINK_CREATE, LINK_UPDATE, OBJ_GET_INFO, to accept attach types tied to
network namespaces (only flow dissector at the moment).
Link-based and prog-based attachment can be used interchangeably, but only
one can exist at a time. Attempts to attach a link when a prog is already
attached directly, and the other way around, will be met with -EEXIST.
Attempts to detach a program when link exists result in -EINVAL.
Attachment of multiple links of same attach type to one netns is not
supported with the intention to lift the restriction when a use-case
presents itself. Because of that link create returns -E2BIG when trying to
create another netns link, when one already exists.
Link-based attachments to netns don't keep a netns alive by holding a ref
to it. Instead links get auto-detached from netns when the latter is being
destroyed, using a pernet pre_exit callback.
When auto-detached, link lives in defunct state as long there are open FDs
for it. -ENOLINK is returned if a user tries to update a defunct link.
Because bpf_link to netns doesn't hold a ref to struct net, special care is
taken when releasing, updating, or filling link info. The netns might be
getting torn down when any of these link operations are in progress. That
is why auto-detach and update/release/fill_info are synchronized by the
same mutex. Also, link ops have to always check if auto-detach has not
happened yet and if netns is still alive (refcnt > 0).
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-5-jakub@cloudflare.com
Move functions to manage BPF programs attached to netns that are not
specific to flow dissector to a dedicated module named
bpf/net_namespace.c.
The set of functions will grow with the addition of bpf_link support for
netns attached programs. This patch prepares ground by creating a place
for it.
This is a code move with no functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-4-jakub@cloudflare.com
In order to:
(1) attach more than one BPF program type to netns, or
(2) support attaching BPF programs to netns with bpf_link, or
(3) support multi-prog attach points for netns
we will need to keep more state per netns than a single pointer like we
have now for BPF flow dissector program.
Prepare for the above by extracting netns_bpf that is part of struct net,
for storing all state related to BPF programs attached to netns.
Turn flow dissector callbacks for querying/attaching/detaching a program
into generic ones that operate on netns_bpf. Next patch will move the
generic callbacks into their own module.
This is similar to how it is organized for cgroup with cgroup_bpf.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-3-jakub@cloudflare.com
Currenty lsm uses bpf_tracing_func_proto helpers which do
not include stack trace or perf event output. It's useful
to have those for bpftrace lsm support [1].
Using tracing_prog_func_proto helpers for lsm programs.
[1] https://github.com/iovisor/bpftrace/pull/1347
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: KP Singh <kpsingh@google.com>
Link: https://lore.kernel.org/bpf/20200531154255.896551-1-jolsa@kernel.org
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
buf_prevkey in generic_map_lookup_batch() is allocated with
kmalloc(). It's safe to free it with kfree().
Fixes: cb4d03ab49 ("bpf: Add generic support for lookup batch op")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200601162814.17426-1-efremov@linux.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add xdp_txq_info as the Tx counterpart to xdp_rxq_info. At the
moment only the device is added. Other fields (queue_index)
can be added as use cases arise.
>From a UAPI perspective, add egress_ifindex to xdp context for
bpf programs to see the Tx device.
Update the verifier to only allow accesses to egress_ifindex by
XDP programs with BPF_XDP_DEVMAP expected attach type.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-4-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add BPF_XDP_DEVMAP attach type for use with programs associated with a
DEVMAP entry.
Allow DEVMAPs to associate a program with a device entry by adding
a bpf_prog.fd to 'struct bpf_devmap_val'. Values read show the program
id, so the fd and id are a union. bpf programs can get access to the
struct via vmlinux.h.
The program associated with the fd must have type XDP with expected
attach type BPF_XDP_DEVMAP. When a program is associated with a device
index, the program is run on an XDP_REDIRECT and before the buffer is
added to the per-cpu queue. At this point rxq data is still valid; the
next patch adds tx device information allowing the prorgam to see both
ingress and egress device indices.
XDP generic is skb based and XDP programs do not work with skb's. Block
the use case by walking maps used by a program that is to be attached
via xdpgeneric and fail if any of them are DEVMAP / DEVMAP_HASH with
Block attach of BPF_XDP_DEVMAP programs to devices.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-3-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add 'struct bpf_devmap_val' to formalize the expected values that can
be passed in for a DEVMAP. Update devmap code to use the struct.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-2-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit adds a new MPSC ring buffer implementation into BPF ecosystem,
which allows multiple CPUs to submit data to a single shared ring buffer. On
the consumption side, only single consumer is assumed.
Motivation
----------
There are two distinctive motivators for this work, which are not satisfied by
existing perf buffer, which prompted creation of a new ring buffer
implementation.
- more efficient memory utilization by sharing ring buffer across CPUs;
- preserving ordering of events that happen sequentially in time, even
across multiple CPUs (e.g., fork/exec/exit events for a task).
These two problems are independent, but perf buffer fails to satisfy both.
Both are a result of a choice to have per-CPU perf ring buffer. Both can be
also solved by having an MPSC implementation of ring buffer. The ordering
problem could technically be solved for perf buffer with some in-kernel
counting, but given the first one requires an MPSC buffer, the same solution
would solve the second problem automatically.
Semantics and APIs
------------------
Single ring buffer is presented to BPF programs as an instance of BPF map of
type BPF_MAP_TYPE_RINGBUF. Two other alternatives considered, but ultimately
rejected.
One way would be to, similar to BPF_MAP_TYPE_PERF_EVENT_ARRAY, make
BPF_MAP_TYPE_RINGBUF could represent an array of ring buffers, but not enforce
"same CPU only" rule. This would be more familiar interface compatible with
existing perf buffer use in BPF, but would fail if application needed more
advanced logic to lookup ring buffer by arbitrary key. HASH_OF_MAPS addresses
this with current approach. Additionally, given the performance of BPF
ringbuf, many use cases would just opt into a simple single ring buffer shared
among all CPUs, for which current approach would be an overkill.
Another approach could introduce a new concept, alongside BPF map, to
represent generic "container" object, which doesn't necessarily have key/value
interface with lookup/update/delete operations. This approach would add a lot
of extra infrastructure that has to be built for observability and verifier
support. It would also add another concept that BPF developers would have to
familiarize themselves with, new syntax in libbpf, etc. But then would really
provide no additional benefits over the approach of using a map.
BPF_MAP_TYPE_RINGBUF doesn't support lookup/update/delete operations, but so
doesn't few other map types (e.g., queue and stack; array doesn't support
delete, etc).
The approach chosen has an advantage of re-using existing BPF map
infrastructure (introspection APIs in kernel, libbpf support, etc), being
familiar concept (no need to teach users a new type of object in BPF program),
and utilizing existing tooling (bpftool). For common scenario of using
a single ring buffer for all CPUs, it's as simple and straightforward, as
would be with a dedicated "container" object. On the other hand, by being
a map, it can be combined with ARRAY_OF_MAPS and HASH_OF_MAPS map-in-maps to
implement a wide variety of topologies, from one ring buffer for each CPU
(e.g., as a replacement for perf buffer use cases), to a complicated
application hashing/sharding of ring buffers (e.g., having a small pool of
ring buffers with hashed task's tgid being a look up key to preserve order,
but reduce contention).
Key and value sizes are enforced to be zero. max_entries is used to specify
the size of ring buffer and has to be a power of 2 value.
There are a bunch of similarities between perf buffer
(BPF_MAP_TYPE_PERF_EVENT_ARRAY) and new BPF ring buffer semantics:
- variable-length records;
- if there is no more space left in ring buffer, reservation fails, no
blocking;
- memory-mappable data area for user-space applications for ease of
consumption and high performance;
- epoll notifications for new incoming data;
- but still the ability to do busy polling for new data to achieve the
lowest latency, if necessary.
BPF ringbuf provides two sets of APIs to BPF programs:
- bpf_ringbuf_output() allows to *copy* data from one place to a ring
buffer, similarly to bpf_perf_event_output();
- bpf_ringbuf_reserve()/bpf_ringbuf_commit()/bpf_ringbuf_discard() APIs
split the whole process into two steps. First, a fixed amount of space is
reserved. If successful, a pointer to a data inside ring buffer data area
is returned, which BPF programs can use similarly to a data inside
array/hash maps. Once ready, this piece of memory is either committed or
discarded. Discard is similar to commit, but makes consumer ignore the
record.
bpf_ringbuf_output() has disadvantage of incurring extra memory copy, because
record has to be prepared in some other place first. But it allows to submit
records of the length that's not known to verifier beforehand. It also closely
matches bpf_perf_event_output(), so will simplify migration significantly.
bpf_ringbuf_reserve() avoids the extra copy of memory by providing a memory
pointer directly to ring buffer memory. In a lot of cases records are larger
than BPF stack space allows, so many programs have use extra per-CPU array as
a temporary heap for preparing sample. bpf_ringbuf_reserve() avoid this needs
completely. But in exchange, it only allows a known constant size of memory to
be reserved, such that verifier can verify that BPF program can't access
memory outside its reserved record space. bpf_ringbuf_output(), while slightly
slower due to extra memory copy, covers some use cases that are not suitable
for bpf_ringbuf_reserve().
The difference between commit and discard is very small. Discard just marks
a record as discarded, and such records are supposed to be ignored by consumer
code. Discard is useful for some advanced use-cases, such as ensuring
all-or-nothing multi-record submission, or emulating temporary malloc()/free()
within single BPF program invocation.
Each reserved record is tracked by verifier through existing
reference-tracking logic, similar to socket ref-tracking. It is thus
impossible to reserve a record, but forget to submit (or discard) it.
bpf_ringbuf_query() helper allows to query various properties of ring buffer.
Currently 4 are supported:
- BPF_RB_AVAIL_DATA returns amount of unconsumed data in ring buffer;
- BPF_RB_RING_SIZE returns the size of ring buffer;
- BPF_RB_CONS_POS/BPF_RB_PROD_POS returns current logical possition of
consumer/producer, respectively.
Returned values are momentarily snapshots of ring buffer state and could be
off by the time helper returns, so this should be used only for
debugging/reporting reasons or for implementing various heuristics, that take
into account highly-changeable nature of some of those characteristics.
One such heuristic might involve more fine-grained control over poll/epoll
notifications about new data availability in ring buffer. Together with
BPF_RB_NO_WAKEUP/BPF_RB_FORCE_WAKEUP flags for output/commit/discard helpers,
it allows BPF program a high degree of control and, e.g., more efficient
batched notifications. Default self-balancing strategy, though, should be
adequate for most applications and will work reliable and efficiently already.
Design and implementation
-------------------------
This reserve/commit schema allows a natural way for multiple producers, either
on different CPUs or even on the same CPU/in the same BPF program, to reserve
independent records and work with them without blocking other producers. This
means that if BPF program was interruped by another BPF program sharing the
same ring buffer, they will both get a record reserved (provided there is
enough space left) and can work with it and submit it independently. This
applies to NMI context as well, except that due to using a spinlock during
reservation, in NMI context, bpf_ringbuf_reserve() might fail to get a lock,
in which case reservation will fail even if ring buffer is not full.
The ring buffer itself internally is implemented as a power-of-2 sized
circular buffer, with two logical and ever-increasing counters (which might
wrap around on 32-bit architectures, that's not a problem):
- consumer counter shows up to which logical position consumer consumed the
data;
- producer counter denotes amount of data reserved by all producers.
Each time a record is reserved, producer that "owns" the record will
successfully advance producer counter. At that point, data is still not yet
ready to be consumed, though. Each record has 8 byte header, which contains
the length of reserved record, as well as two extra bits: busy bit to denote
that record is still being worked on, and discard bit, which might be set at
commit time if record is discarded. In the latter case, consumer is supposed
to skip the record and move on to the next one. Record header also encodes
record's relative offset from the beginning of ring buffer data area (in
pages). This allows bpf_ringbuf_commit()/bpf_ringbuf_discard() to accept only
the pointer to the record itself, without requiring also the pointer to ring
buffer itself. Ring buffer memory location will be restored from record
metadata header. This significantly simplifies verifier, as well as improving
API usability.
Producer counter increments are serialized under spinlock, so there is
a strict ordering between reservations. Commits, on the other hand, are
completely lockless and independent. All records become available to consumer
in the order of reservations, but only after all previous records where
already committed. It is thus possible for slow producers to temporarily hold
off submitted records, that were reserved later.
Reservation/commit/consumer protocol is verified by litmus tests in
Documentation/litmus-test/bpf-rb.
One interesting implementation bit, that significantly simplifies (and thus
speeds up as well) implementation of both producers and consumers is how data
area is mapped twice contiguously back-to-back in the virtual memory. This
allows to not take any special measures for samples that have to wrap around
at the end of the circular buffer data area, because the next page after the
last data page would be first data page again, and thus the sample will still
appear completely contiguous in virtual memory. See comment and a simple ASCII
diagram showing this visually in bpf_ringbuf_area_alloc().
Another feature that distinguishes BPF ringbuf from perf ring buffer is
a self-pacing notifications of new data being availability.
bpf_ringbuf_commit() implementation will send a notification of new record
being available after commit only if consumer has already caught up right up
to the record being committed. If not, consumer still has to catch up and thus
will see new data anyways without needing an extra poll notification.
Benchmarks (see tools/testing/selftests/bpf/benchs/bench_ringbuf.c) show that
this allows to achieve a very high throughput without having to resort to
tricks like "notify only every Nth sample", which are necessary with perf
buffer. For extreme cases, when BPF program wants more manual control of
notifications, commit/discard/output helpers accept BPF_RB_NO_WAKEUP and
BPF_RB_FORCE_WAKEUP flags, which give full control over notifications of data
availability, but require extra caution and diligence in using this API.
Comparison to alternatives
--------------------------
Before considering implementing BPF ring buffer from scratch existing
alternatives in kernel were evaluated, but didn't seem to meet the needs. They
largely fell into few categores:
- per-CPU buffers (perf, ftrace, etc), which don't satisfy two motivations
outlined above (ordering and memory consumption);
- linked list-based implementations; while some were multi-producer designs,
consuming these from user-space would be very complicated and most
probably not performant; memory-mapping contiguous piece of memory is
simpler and more performant for user-space consumers;
- io_uring is SPSC, but also requires fixed-sized elements. Naively turning
SPSC queue into MPSC w/ lock would have subpar performance compared to
locked reserve + lockless commit, as with BPF ring buffer. Fixed sized
elements would be too limiting for BPF programs, given existing BPF
programs heavily rely on variable-sized perf buffer already;
- specialized implementations (like a new printk ring buffer, [0]) with lots
of printk-specific limitations and implications, that didn't seem to fit
well for intended use with BPF programs.
[0] https://lwn.net/Articles/779550/
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200529075424.3139988-2-andriin@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The map_lookup_and_delete_elem() function should check for both FMODE_CAN_WRITE
and FMODE_CAN_READ permissions because it returns a map element to user space.
Fixes: bd513cd08f ("bpf: add MAP_LOOKUP_AND_DELETE_ELEM syscall")
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200527185700.14658-5-a.s.protopopov@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Often it is useful when applying policy to know something about the
task. If the administrator has CAP_SYS_ADMIN rights then they can
use kprobe + networking hook and link the two programs together to
accomplish this. However, this is a bit clunky and also means we have
to call both the network program and kprobe program when we could just
use a single program and avoid passing metadata through sk_msg/skb->cb,
socket, maps, etc.
To accomplish this add probe_* helpers to bpf_base_func_proto programs
guarded by a perfmon_capable() check. New supported helpers are the
following,
BPF_FUNC_get_current_task
BPF_FUNC_probe_read_user
BPF_FUNC_probe_read_kernel
BPF_FUNC_probe_read_user_str
BPF_FUNC_probe_read_kernel_str
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/159033905529.12355.4368381069655254932.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
System calls encode returned errors as negative values. Fix a typo that
breaks this convention for bpf(LINK_UPDATE) when bpf_link doesn't support
update operation.
Fixes: f9d041271c ("bpf: Refactor bpf_link update handling")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200525122928.1164495-1-jakub@cloudflare.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest trunk llvm (llvm 11), I hit a verifier issue for
test_prog subtest test_verif_scale1.
The following simplified example illustrate the issue:
w9 = 0 /* R9_w=inv0 */
r8 = *(u32 *)(r1 + 80) /* __sk_buff->data_end */
r7 = *(u32 *)(r1 + 76) /* __sk_buff->data */
......
w2 = w9 /* R2_w=inv0 */
r6 = r7 /* R6_w=pkt(id=0,off=0,r=0,imm=0) */
r6 += r2 /* R6_w=inv(id=0) */
r3 = r6 /* R3_w=inv(id=0) */
r3 += 14 /* R3_w=inv(id=0) */
if r3 > r8 goto end
r5 = *(u32 *)(r6 + 0) /* R6_w=inv(id=0) */
<== error here: R6 invalid mem access 'inv'
...
end:
In real test_verif_scale1 code, "w9 = 0" and "w2 = w9" are in
different basic blocks.
In the above, after "r6 += r2", r6 becomes a scalar, which eventually
caused the memory access error. The correct register state should be
a pkt pointer.
The inprecise register state starts at "w2 = w9".
The 32bit register w9 is 0, in __reg_assign_32_into_64(),
the 64bit reg->smax_value is assigned to be U32_MAX.
The 64bit reg->smin_value is 0 and the 64bit register
itself remains constant based on reg->var_off.
In adjust_ptr_min_max_vals(), the verifier checks for a known constant,
smin_val must be equal to smax_val. Since they are not equal,
the verifier decides r6 is a unknown scalar, which caused later failure.
The llvm10 does not have this issue as it generates different code:
w9 = 0 /* R9_w=inv0 */
r8 = *(u32 *)(r1 + 80) /* __sk_buff->data_end */
r7 = *(u32 *)(r1 + 76) /* __sk_buff->data */
......
r6 = r7 /* R6_w=pkt(id=0,off=0,r=0,imm=0) */
r6 += r9 /* R6_w=pkt(id=0,off=0,r=0,imm=0) */
r3 = r6 /* R3_w=pkt(id=0,off=0,r=0,imm=0) */
r3 += 14 /* R3_w=pkt(id=0,off=14,r=0,imm=0) */
if r3 > r8 goto end
...
To fix the above issue, we can include zero in the test condition for
assigning the s32_max_value and s32_min_value to their 64-bit equivalents
smax_value and smin_value.
Further, fix the condition to avoid doing zero extension bounds checks
when s32_min_value <= 0. This could allow for the case where bounds
32-bit bounds (-1,1) get incorrectly translated to (0,1) 64-bit bounds.
When in-fact the -1 min value needs to force U32_MAX bound.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/159077331983.6014.5758956193749002737.stgit@john-Precision-5820-Tower
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when considering the branches that may be taken for a jump
instruction if the register being compared is a pointer the verifier
assumes both branches may be taken. But, if the jump instruction
is comparing if a pointer is NULL we have this information in the
verifier encoded in the reg->type so we can do better in these cases.
Specifically, these two common cases can be handled.
* If the instruction is BPF_JEQ and we are comparing against a
zero value. This test is 'if ptr == 0 goto +X' then using the
type information in reg->type we can decide if the ptr is not
null. This allows us to avoid pushing both branches onto the
stack and instead only use the != 0 case. For example
PTR_TO_SOCK and PTR_TO_SOCK_OR_NULL encode the null pointer.
Note if the type is PTR_TO_SOCK_OR_NULL we can not learn anything.
And also if the value is non-zero we learn nothing because it
could be any arbitrary value a different pointer for example
* If the instruction is BPF_JNE and ware comparing against a zero
value then a similar analysis as above can be done. The test in
asm looks like 'if ptr != 0 goto +X'. Again using the type
information if the non null type is set (from above PTR_TO_SOCK)
we know the jump is taken.
In this patch we extend is_branch_taken() to consider this extra
information and to return only the branch that will be taken. This
resolves a verifier issue reported with C code like the following.
See progs/test_sk_lookup_kern.c in selftests.
sk = bpf_sk_lookup_tcp(skb, tuple, tuple_len, BPF_F_CURRENT_NETNS, 0);
bpf_printk("sk=%d\n", sk ? 1 : 0);
if (sk)
bpf_sk_release(sk);
return sk ? TC_ACT_OK : TC_ACT_UNSPEC;
In the above the bpf_printk() will resolve the pointer from
PTR_TO_SOCK_OR_NULL to PTR_TO_SOCK. Then the second test guarding
the release will cause the verifier to walk both paths resulting
in the an unreleased sock reference. See verifier/ref_tracking.c
in selftests for an assembly version of the above.
After the above additional logic is added the C code above passes
as expected.
Reported-by: Andrey Ignatov <rdna@fb.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159009164651.6313.380418298578070501.stgit@john-Precision-5820-Tower
The XSKMAP is partly implemented by net/xdp/xsk.c. Move xskmap.c from
kernel/bpf/ to net/xdp/, which is the logical place for AF_XDP related
code. Also, move AF_XDP struct definitions, and function declarations
only used by AF_XDP internals into net/xdp/xsk.h.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-3-bjorn.topel@gmail.com
As discussed in [0], it's dangerous to allow mapping BPF map, that's meant to
be frozen and is read-only on BPF program side, because that allows user-space
to actually store a writable view to the page even after it is frozen. This is
exacerbated by BPF verifier making a strong assumption that contents of such
frozen map will remain unchanged. To prevent this, disallow mapping
BPF_F_RDONLY_PROG mmap()'able BPF maps as writable, ever.
[0] https://lore.kernel.org/bpf/CAEf4BzYGWYhXdp6BJ7_=9OQPJxQpgug080MMjdSB72i9R+5c6g@mail.gmail.com/
Fixes: fc9702273e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/bpf/20200519053824.1089415-1-andriin@fb.com
As stated in 983695fa67 ("bpf: fix unconnected udp hooks"), the objective
for the existing cgroup connect/sendmsg/recvmsg/bind BPF hooks is to be
transparent to applications. In Cilium we make use of these hooks [0] in
order to enable E-W load balancing for existing Kubernetes service types
for all Cilium managed nodes in the cluster. Those backends can be local
or remote. The main advantage of this approach is that it operates as close
as possible to the socket, and therefore allows to avoid packet-based NAT
given in connect/sendmsg/recvmsg hooks we only need to xlate sock addresses.
This also allows to expose NodePort services on loopback addresses in the
host namespace, for example. As another advantage, this also efficiently
blocks bind requests for applications in the host namespace for exposed
ports. However, one missing item is that we also need to perform reverse
xlation for inet{,6}_getname() hooks such that we can return the service
IP/port tuple back to the application instead of the remote peer address.
The vast majority of applications does not bother about getpeername(), but
in a few occasions we've seen breakage when validating the peer's address
since it returns unexpectedly the backend tuple instead of the service one.
Therefore, this trivial patch allows to customise and adds a getpeername()
as well as getsockname() BPF cgroup hook for both IPv4 and IPv6 in order
to address this situation.
Simple example:
# ./cilium/cilium service list
ID Frontend Service Type Backend
1 1.2.3.4:80 ClusterIP 1 => 10.0.0.10:80
Before; curl's verbose output example, no getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (10.0.0.10) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
After; with getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (1.2.3.4) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
Originally, I had both under a BPF_CGROUP_INET{4,6}_GETNAME type and exposed
peer to the context similar as in inet{,6}_getname() fashion, but API-wise
this is suboptimal as it always enforces programs having to test for ctx->peer
which can easily be missed, hence BPF_CGROUP_INET{4,6}_GET{PEER,SOCK}NAME split.
Similarly, the checked return code is on tnum_range(1, 1), but if a use case
comes up in future, it can easily be changed to return an error code instead.
Helper and ctx member access is the same as with connect/sendmsg/etc hooks.
[0] https://github.com/cilium/cilium/blob/master/bpf/bpf_sock.c
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/61a479d759b2482ae3efb45546490bacd796a220.1589841594.git.daniel@iogearbox.net
As per 15d83c4d7c ("bpf: Allow loading of a bpf_iter program") we only
allow a range of [0,1] for return codes. Therefore BPF_TRACE_ITER relies
on the default tnum_range(0, 1) which is set in range var. On recent merge
of net into net-next commit e92888c72f ("bpf: Enforce returning 0 for
fentry/fexit progs") got pulled in and caused a merge conflict with the
changes from 15d83c4d7c. The resolution had a snall hiccup in that it
removed the [0,1] range restriction again so that BPF_TRACE_ITER would
have no enforcement. Fix it by adding it back.
Fixes: da07f52d3c ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement permissions as stated in uapi/linux/capability.h
In order to do that the verifier allow_ptr_leaks flag is split
into four flags and they are set as:
env->allow_ptr_leaks = bpf_allow_ptr_leaks();
env->bypass_spec_v1 = bpf_bypass_spec_v1();
env->bypass_spec_v4 = bpf_bypass_spec_v4();
env->bpf_capable = bpf_capable();
The first three currently equivalent to perfmon_capable(), since leaking kernel
pointers and reading kernel memory via side channel attacks is roughly
equivalent to reading kernel memory with cap_perfmon.
'bpf_capable' enables bounded loops, precision tracking, bpf to bpf calls and
other verifier features. 'allow_ptr_leaks' enable ptr leaks, ptr conversions,
subtraction of pointers. 'bypass_spec_v1' disables speculative analysis in the
verifier, run time mitigations in bpf array, and enables indirect variable
access in bpf programs. 'bypass_spec_v4' disables emission of sanitation code
by the verifier.
That means that the networking BPF program loaded with CAP_BPF + CAP_NET_ADMIN
will have speculative checks done by the verifier and other spectre mitigation
applied. Such networking BPF program will not be able to leak kernel pointers
and will not be able to access arbitrary kernel memory.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200513230355.7858-3-alexei.starovoitov@gmail.com
Given bpf_probe_read{,str}() BPF helpers are now only available under
CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE, we need to add the drop-in
replacements of bpf_probe_read_{kernel,user}_str() to do_refine_retval_range()
as well to avoid hitting the same issue as in 849fa50662 ("bpf/verifier:
refine retval R0 state for bpf_get_stack helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200515101118.6508-3-daniel@iogearbox.net
Knowing the memory size backing the packet/xdp_frame data area, and
knowing it already have reserved room for skb_shared_info, simplifies
using build_skb significantly.
With this change we no-longer lie about the SKB truesize, but more
importantly a significant larger skb_tailroom is now provided, e.g. when
drivers uses a full PAGE_SIZE. This extra tailroom (in linear area) can be
used by the network stack when coalescing SKBs (e.g. in skb_try_coalesce,
see TCP cases where tcp_queue_rcv() can 'eat' skb).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945337822.97035.13557959180460986059.stgit@firesoul
task_seq_get_next might stop prematurely if get_pid_task() fails to get
task_struct. Failure to do so doesn't mean that there are no more tasks with
higher pids. Procfs's iteration algorithm (see next_tgid in fs/proc/base.c)
does a retry in such case. After this fix, instead of stopping prematurely
after about 300 tasks on my server, bpf_iter program now returns >4000, which
sounds much closer to reality.
Fixes: eaaacd2391 ("bpf: Add task and task/file iterator targets")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200514055137.1564581-1-andriin@fb.com
Currently, tracing/fentry and tracing/fexit prog
return values are not enforced. In trampoline codes,
the fentry/fexit prog return values are ignored.
Let us enforce it to be 0 to avoid confusion and
allows potential future extension.
This patch also explicitly added return value
checking for tracing/raw_tp, tracing/fmod_ret,
and freplace programs such that these program
return values can be anything. The purpose are
two folds:
1. to make it explicit about return value expectations
for these programs in verifier.
2. for tracing prog_type, if a future attach type
is added, the default is -ENOTSUPP which will
enforce to specify return value ranges explicitly.
Fixes: fec56f5890 ("bpf: Introduce BPF trampoline")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200514053206.1298415-1-yhs@fb.com
mmap() subsystem allows user-space application to memory-map region with
initial page offset. This wasn't taken into account in initial implementation
of BPF array memory-mapping. This would result in wrong pages, not taking into
account requested page shift, being memory-mmaped into user-space. This patch
fixes this gap and adds a test for such scenario.
Fixes: fc9702273e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200512235925.3817805-1-andriin@fb.com
Commit b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL
support") adds a field btf_id_or_null_non0_off to
bpf_prog->aux structure to indicate that the
first ctx argument is PTR_TO_BTF_ID reg_type and
all others are PTR_TO_BTF_ID_OR_NULL.
This approach does not really scale if we have
other different reg types in the future, e.g.,
a pointer to a buffer.
This patch enables bpf_iter targets registering ctx argument
reg types which may be different from the default one.
For example, for pointers to structures, the default reg_type
is PTR_TO_BTF_ID for tracing program. The target can register
a particular pointer type as PTR_TO_BTF_ID_OR_NULL which can
be used by the verifier to enforce accesses.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180221.2949882-1-yhs@fb.com
Change func bpf_iter_unreg_target() parameter from target
name to target reg_info, similar to bpf_iter_reg_target().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180220.2949737-1-yhs@fb.com
Currently bpf_iter_reg_target takes parameters from target
and allocates memory to save them. This is really not
necessary, esp. in the future we may grow information
passed from targets to bpf_iter manager.
The patch refactors the code so target reg_info
becomes static and bpf_iter manager can just take
a reference to it.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200513180219.2949605-1-yhs@fb.com
Add a short comment in bpf_iter_run_prog() function to
explain how bpf_prog return value is converted to
seq_ops->show() return value:
bpf_prog return seq_ops()->show() return
0 0
1 -EAGAIN
When show() return value is -EAGAIN, the current
bpf_seq_read() will end. If the current seq_file buffer
is empty, -EAGAIN will return to user space. Otherwise,
the buffer will be copied to user space.
In both cases, the next bpf_seq_read() call will
try to show the same object which returned -EAGAIN
previously.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180218.2949517-1-yhs@fb.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200507185057.GA13981@embeddedor
Add bpf_reg_type PTR_TO_BTF_ID_OR_NULL support.
For tracing/iter program, the bpf program context
definition, e.g., for previous bpf_map target, looks like
struct bpf_iter__bpf_map {
struct bpf_iter_meta *meta;
struct bpf_map *map;
};
The kernel guarantees that meta is not NULL, but
map pointer maybe NULL. The NULL map indicates that all
objects have been traversed, so bpf program can take
proper action, e.g., do final aggregation and/or send
final report to user space.
Add btf_id_or_null_non0_off to prog->aux structure, to
indicate that if the context access offset is not 0,
set to PTR_TO_BTF_ID_OR_NULL instead of PTR_TO_BTF_ID.
This bit is set for tracing/iter program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175912.2476576-1-yhs@fb.com
Only the tasks belonging to "current" pid namespace
are enumerated.
For task/file target, the bpf program will have access to
struct task_struct *task
u32 fd
struct file *file
where fd/file is an open file for the task.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175911.2476407-1-yhs@fb.com
Macro DEFINE_BPF_ITER_FUNC is implemented so target
can define an init function to capture the BTF type
which represents the target.
The bpf_iter_meta is a structure holding meta data, common
to all targets in the bpf program.
Additional marker functions are called before or after
bpf_seq_read() show()/next()/stop() callback functions
to help calculate precise seq_num and whether call bpf_prog
inside stop().
Two functions, bpf_iter_get_info() and bpf_iter_run_prog(),
are implemented so target can get needed information from
bpf_iter infrastructure and can run the program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175907.2475956-1-yhs@fb.com
To produce a file bpf iterator, the fd must be
corresponding to a link_fd assocciated with a
trace/iter program. When the pinned file is
opened, a seq_file will be generated.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175906.2475893-1-yhs@fb.com
A new bpf command BPF_ITER_CREATE is added.
The anonymous bpf iterator is seq_file based.
The seq_file private data are referenced by targets.
The bpf_iter infrastructure allocated additional space
at seq_file->private before the space used by targets
to store some meta data, e.g.,
prog: prog to run
session_id: an unique id for each opened seq_file
seq_num: how many times bpf programs are queried in this session
done_stop: an internal state to decide whether bpf program
should be called in seq_ops->stop() or not
The seq_num will start from 0 for valid objects.
The bpf program may see the same seq_num more than once if
- seq_file buffer overflow happens and the same object
is retried by bpf_seq_read(), or
- the bpf program explicitly requests a retry of the
same object
Since module is not supported for bpf_iter, all target
registeration happens at __init time, so there is no
need to change bpf_iter_unreg_target() as it is used
mostly in error path of the init function at which time
no bpf iterators have been created yet.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175905.2475770-1-yhs@fb.com
bpf iterator uses seq_file to provide a lossless
way to transfer data to user space. But we want to call
bpf program after all objects have been traversed, and
bpf program may write additional data to the
seq_file buffer. The current seq_read() does not work
for this use case.
Besides allowing stop() function to write to the buffer,
the bpf_seq_read() also fixed the buffer size to one page.
If any single call of show() or stop() will emit data
more than one page to cause overflow, -E2BIG error code
will be returned to user space.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175904.2475468-1-yhs@fb.com
