Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab507 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the support for configuring periodic output
signal of PPS. So the PPS can be output at a specified time
and period.
For developers or testers, they can use the command "echo
<channel> <start.sec> <start.nsec> <period.sec> <period.
nsec> > /sys/class/ptp/ptp0/period" to specify time and
period to output PPS signal.
Notice that, the channel can only be set to 0. In addtion,
the start time must larger than the current PTP clock time.
So users can use the command "phc_ctl /dev/ptp0 -- get" to
get the current PTP clock time before.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before 262f2b782e ("net: fman: Map the base address once"), the
physical address of the MAC was exposed to userspace in two places: via
sysfs and via SIOCGIFMAP. While this is not best practice, it is an
external ABI which is in use by userspace software.
The aforementioned commit inadvertently modified these addresses and
made them virtual. This constitutes and ABI break. Additionally, it
leaks the kernel's memory layout to userspace. Partially revert that
commit, reintroducing the resource back into struct mac_device, while
keeping the intended changes (the rework of the address mapping).
Fixes: 262f2b782e ("net: fman: Map the base address once")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the dpaa2_tx_xsk_fd and dpaa2_rx_xsk_fd trace events for the XSK
zero-copy Rx and Tx path. Also, define the dpaa2_eth_buf as an event
class so that both dpaa2_eth_buf_seed and dpaa2_xsk_buf_seed traces can
derive from the same class.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for packet processing on the Tx path using
AF_XDP zero copy mode.
The newly added dpaa2_xsk_tx() function will handle enqueuing AF_XDP Tx
packets into the appropriate queue and update any necessary statistics.
On a more detailed note, the dpaa2_xsk_tx_build_fd() function handles
creating a Scatter-Gather frame descriptor with only one data buffer.
This is needed because otherwise we would need to impose a headroom in
the Tx buffer to store our software annotation structures.
This tactic is already used on the normal data path of the dpaa2-eth
driver, thus we are reusing the dpaa2_eth_sgt_get/dpaa2_eth_sgt_recycle
functions in order to allocate and recycle the Scatter-Gather table
buffers.
In case we have reached the maximum number of Tx XSK packets to be sent
in a NAPI cycle, we'll exit the dpaa2_eth_poll() and hope to be
rescheduled again.
On the XSK Tx confirmation path, we are just unmapping the SGT buffer
and recycle it for further use.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for receiving packets via the AF_XDP
zero-copy mechanism in the dpaa2-eth driver. The support is available
only on the LX2160A SoC and variants because we are relying on the HW
capability to associate a buffer pool to a specific queue (QDBIN), only
available on newer WRIOP versions.
On the control path, the dpaa2_xsk_enable_pool() function is responsible
to allocate a buffer pool (BP), setup this new BP to be used only on the
requested queue and change the consume function to point to the XSK ZC
one.
We are forced to call dev_close() in order to change the queue to buffer
pool association (dpaa2_xsk_set_bp_per_qdbin) . This also works in our
favor since at dev_close() the buffer pools will be drained and at the
later dev_open() call they will be again seeded, this time with buffers
allocated from the XSK pool if needed.
On the data path, a new software annotation type is defined to be used
only for the XSK scenarios. This will enable us to pass keep necessary
information about a packet buffer between the moment in which it was
seeded and when it's received by the driver. In the XSK case, we are
keeping the associated xdp_buff.
Depending on the action returned by the BPF program, we will do the
following:
- XDP_PASS: copy the contents of the packet into a brand new skb,
recycle the initial buffer.
- XDP_TX: just enqueue the same frame descriptor back into the Tx path,
the buffer will get automatically released into the initial BP.
- XDP_REDIRECT: call xdp_do_redirect() and exit.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carve out code from the dpaa2_eth_rx() function in order to create and
export the dpaa2_eth_receive_skb() function. Do this in order to reuse
this code also from the XSK path which will be introduced in a later
patch.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2_eth_alloc_skb() function is added by moving code from the
dpaa2_eth_copybreak() previously defined function. What the new API does
is to allocate a new skb, copy the frame data from the passed FD to the
new skb and then return the skb.
Export this new function since we'll need the this functionality also
from the XSK code path.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling the internal functions which implement .ndo_stop and
.ndo_open, we can simply call dev_close and dev_open, so that we keep
the code cleaner.
Also, in the next patches we'll use the same APIs from other files
without needing to export the internal functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dpni_set_pool() firmware API so that in the next patches we
can configure per Rx queue (per QDBIN) buffer pools.
This is a hard requirement of the AF_XDP, thus we need the newer API
version.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the allocated buffer pools, the number of buffers that they have
currently and which channels are using which BP.
The output looks like below:
Buffer pool info for eth2:
IDX BPID Buf count CH#0 CH#1 CH#2 CH#3
BP#0 1 5124 x x x x
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just give out an index for each channel that we export into the debug
file in the form of CH#<index>. This is purely to help corelate each
channel information from one debugfs file to another one.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the configuration of multiple buffer pools associated
with a single DPNI object, each distinct DPBP object not necessarily
shared among all queues.
The user can interogate both the number of buffer pools and the buffer
count in each buffer pool by using the .get_ethtool_stats() callback.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the variables in the dpaa2_eth_get_ethtool_stats() function so
that we adhere to the reverse Christmas tree rule.
Also, in the next patch we are adding more variables and I didn't know
where to place them with the current ordering.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .get_channels() ethtool_ops callback is implemented and exports the
number of queues: Rx, Tx, Tx conf and Rx err.
The last two ones, Tx confirmation and Rx err, are counted as 'others'.
The .set_channels() callback is not implemented since the DPAA2
software/firmware architecture does not allow the dynamic
reconfiguration of the number of queues.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts DPAA to phylink. All macs are converted. This should work
with no device tree modifications (including those made in this series),
except for QSGMII (as noted previously).
The mEMAC configuration is one of the tricker areas. I have tried to
capture all the restrictions across the various models. Most of the time,
we assume that if the serdes supports a mode or the phy-interface-mode
specifies it, then we support it. The only place we can't do this is
(RG)MII, since there's no serdes. In that case, we rely on a (new)
devicetree property. There are also several cases where half-duplex is
broken. Unfortunately, only a single compatible is used for the MAC, so we
have to use the board compatible instead.
The 10GEC conversion is very straightforward, since it only supports XAUI.
There is generally nothing to configure.
The dTSEC conversion is broadly similar to mEMAC, but is simpler because we
don't support configuring the SerDes (though this can be easily added) and
we don't have multiple PCSs. From what I can tell, there's nothing
different in the driver or documentation between SGMII and 1000BASE-X
except for the advertising. Similarly, I couldn't find anything about
2500BASE-X. In both cases, I treat them like SGMII. These modes aren't used
by any in-tree boards. Similarly, despite being mentioned in the driver, I
couldn't find any documented SoCs which supported QSGMII. I have left it
unimplemented for now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not stated in the datasheet, as far as I can tell PCS for mEMACs
is a "Lynx." By reusing the existing driver, we can remove the PCS
management code from the memac driver. This requires calling some PCS
functions manually which phylink would usually do for us, but we will let
it do that soon.
One problem is that we don't actually have a PCS for QSGMII. We pretend
that each mEMAC's MDIO bus has four QSGMII PCSs, but this is not the case.
Only the "base" mEMAC's MDIO bus has the four QSGMII PCSs. This is not an
issue yet, because we never get the PCS state. However, it will be once the
conversion to phylink is complete, since the links will appear to never
come up. To get around this, we allow specifying multiple PCSs in pcsphy.
This breaks backwards compatibility with old device trees, but only for
QSGMII. IMO this is the only reasonable way to figure out what the actual
QSGMII PCS is.
Additionally, we now also support a separate XFI PCS. This can allow the
SerDes driver to set different addresses for the SGMII and XFI PCSs so they
can be accessed at the same time.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for using a serdes which has to be configured. This is
primarly in preparation for phylink conversion, which will then change the
serdes mode dynamically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/pkt_sched.h is included twice in enetc_qos.c,
remove one of them.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2334
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently sets the PTCMSDUR register statically to the max
MTU supported by the interface. Keep this logic if tc-taprio is absent
or if the max_sdu for a traffic class is 0, and follow the requested max
SDU size otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Port Time Gating Control Register (PTGCR) and Port Time Gating
Capability Register (PTGCAPR) have definitions in the driver which
aren't in line with the other registers. Rename these.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The &priv->si->hw construct dereferences 2 pointers and makes lines
longer than they need to be, in turn making the code harder to read.
Replace &priv->si->hw accesses with a "hw" variable when there are 2 or
more accesses within a function that dereference this. This includes
loops, since &priv->si->hw is a loop invariant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TSN features on the ENETC (taprio, cbs, gate, police) are configured
through a mix of command BD ring messages and port registers:
enetc_port_rd(), enetc_port_wr().
Port registers are a region of the ENETC memory map which are only
accessible from the PCIe Physical Function. They are not accessible from
the Virtual Functions.
Moreover, attempting to access these registers crashes the kernel:
$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0
$ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \
sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2
Unable to handle kernel paging request at virtual address ffff800009551a08
Internal error: Oops: 96000007 [#1] PREEMPT SMP
pc : enetc_setup_tc_taprio+0x170/0x47c
lr : enetc_setup_tc_taprio+0x16c/0x47c
Call trace:
enetc_setup_tc_taprio+0x170/0x47c
enetc_setup_tc+0x38/0x2dc
taprio_change+0x43c/0x970
taprio_init+0x188/0x1e0
qdisc_create+0x114/0x470
tc_modify_qdisc+0x1fc/0x6c0
rtnetlink_rcv_msg+0x12c/0x390
Split enetc_setup_tc() into separate functions for the PF and for the
VF drivers. Also remove enetc_qos.o from being included into
enetc-vf.ko, since it serves absolutely no purpose there.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC
flag; only PFs should. Moreover, TSN-specific code should go to
enetc_qos.c, which should not be included in the VF driver.
Fixes: 79e499829f ("net: enetc: add hw tc hw offload features for PSPF capability")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Structure the code in such a way that it can be reused later for the
pMAC statistics, by just changing the "mac" argument to 1.
Usage:
ethtool --include-statistics --show-pause eno2
ethtool -S eno0 --groups eth-mac
ethtool -S eno0 --groups eth-ctrl
ethtool -S eno0 --groups rmon
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENETC has counters for the eMAC and for the pMAC exactly 0x1000
apart from each other. The driver only contains definitions for PM0,
the eMAC.
Rather than duplicating everything for PM1, modify the register
definitions such that they take the MAC as argument.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update Kconfig to also check for ARCH_S32.
Add compatible string and quirks for fsl,s32v234
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fs_mii_disconnect and fs_mii_connect have been removed since
commit 5b4b845434 ("[PATCH] FS_ENET: use PAL for mii management"),
so remove them.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220909062959.1144493-1-cuigaosheng1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Should check of_iomap return value 'fep->fec.fecp' instead of 'fep->fcc.fccp'
Fixes: 976de6a8c3 ("fs_enet: Be an of_platform device when CONFIG_PPC_CPM_NEW_BINDING is set.")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force mii bus into runtime pm suspend state during device suspends,
since phydev state is already PHY_HALTED, and there is no need to
access mii bus during device suspend state. Then force mii bus into
runtime pm resume state when device resumes.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of setting the queue depth once during probe, adjust it on the
fly whenever we configure the link. This is a bit unusal, since usually
the DPAA driver calls into the FMAN driver, but here we do the opposite.
We need to add a netdev to struct mac_device for this, but it will soon
live in the phylink config.
I haven't tested this extensively, but it doesn't seem to break
anything. We could possibly optimize this a bit by keeping track of the
last rate, but for now we just update every time. 10GEC probably doesn't
need to call into this at all, but I've added it for consistency.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several references to mac_dev in dpaa_netdev_init. Make things a
bit more concise by adding a local variable for it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling, there is nothing we can do about errors. In fact, the
only error which can occur is misuse of the API. Just warn in the mac
driver instead.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the _return label, since something like
err = -EFOO;
goto _return;
can be replaced by the briefer
return -EFOO;
Additionally, this skips going to _return_of_node_put when dev_node has
already been put (preventing a double put).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a void pointer for mac_dev, specify its type
explicitly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some params are already present in mac_dev. Use them directly instead of
passing them through params.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the mac init functions call back into the fman core to
get their params, just pass them directly to the init functions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to remap the base address from the resource twice (once in
mac_probe() and again in set_fman_mac_params()). We still need the
resource to get the end address, but we can use a single function call
to get both at once.
While we're at it, use platform_get_mem_or_io and devm_request_resource
to map the resource. I think this is the more "correct" way to do things
here, since we use the pdev resource, instead of creating a new one.
It's still a bit tricky, since we need to ensure that the resource is a
child of the fman region when it gets requested.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This member was used to pass the phy node between mac_probe and the
mac-specific initialization function. But now that the phy node is
gotten in the initialization function, this parameter does not serve a
purpose. Remove it, and do the grabbing of the node/grabbing of the phy
in the same place.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several small functions which were only necessary because the
initialization functions didn't have access to the mac private data. Now
that they do, just do things directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These methods are no longer accessed outside of the driver file, so mark
them as static.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves mac-specific initialization to mac-specific files. This will
make it easier to work with individual macs. It will also make it easier
to refactor the initialization to simplify the control flow. No
functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support stop mode by calling machine api.
The patch add dts support to set GPR register for stop request.
imx8mq enter stop/exit stop mode by setting GPR bit, which can
be accessed by A core.
imx8qm enter stop/exit stop mode by calling IMX_SC ipc APIs that
communicate with M core ipc service, and the M core set the related
GPR bit at last.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mutexes cannot be taken in a non-preemptible context,
causing a panic in `fec_ptp_save_state()`. Replacing
`ptp_clk_mutex` by `tmreg_lock` fixes this.
Fixes: 6a4d7234ae ("net: fec: ptp: avoid register access when ipg clock is disabled")
Fixes: f79959220f ("fec: Restart PPS after link state change")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/20220827160922.642zlcd5foopozru@pengutronix.de/
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis iMX6
Link: https://lore.kernel.org/r/20220901140402.64804-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a very low probability that tx timeout will occur during
suspend and resume stress test on imx6q platform. So we add pm_qos
support to prevent system from entering low level idles which may
affect the transmission of tx.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20220830070148.2021947-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "fixed_link" is only allocated sometimes but it's freed
unconditionally in the error handling. Set it to NULL so we don't free
uninitialized data.
Fixes: 9ea4742a55 ("net: fman: Configure fixed link in memac_initialization")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/Ywd2X6gdKmTfYBxD@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device.
Instead, use the specific dev_fwnode() API for that.
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option is present in params, so use it instead of the fman private
version.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for moving each of the initialization functions to their
own file, export some common functions so they can be re-used. This adds
an fman prefix to set_multi to make it a bit less genericly-named.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
memac is the only mac which parses fixed links. Move the
parsing/configuring to its initialization function.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the reference to our device to mac_device. This way, macs can use
it in their log messages.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of re-matching the compatible string in order to determine the init
function, just store it in the match data. The separate setup functions
aren't needed anymore. Merge their content into init as well. To ensure
everything compiles correctly, we move them to the bottom of the file.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This moves the reading of the PCS property out of the generic probe and
into the mac-specific initialization function. This reduces the
mac-specific jobs done in the top-level probe function.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two ways that GRS can be set: graceful_stop and dtsec_isr. It
is cleared by graceful_start. If it is already set before calling
graceful_stop, then that means that dtsec_isr set it. In that case, we
will not set GRS nor will we clear it (which seems like a bug?). For GTS
the logic is similar, except that there is no one else messing with this
bit (so we will always set and clear it). Simplify the logic by always
setting/clearing GRS/GTS. This is less racy that the previous behavior,
and ensures that we always end up clearing the bits. This can of course
clear GRS while dtsec_isr is waiting, but because we have already done
our own waiting it should be fine.
This is the last user of enum comm_mode, so remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All macs use the same start/stop functions. The actual mac-specific code
lives in enable/disable. Move these functions to an appropriate struct,
and inline the phy enable/disable calls to the caller of start/stop.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mac_priv_s->enable() and ->disable() are always called with
a comm_mode of COMM_MODE_RX_AND_TX. Remove this parameter, and refactor
the macs appropriately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the license text of files in the fman directory to use
SPDX license identifiers instead.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As discussed in commit 73a21fa817 ("dpaa_eth: support all modes with
rate adapting PHYs"), we must add a workaround for Aquantia phys with
in-tree support in order to keep 1G support working. Update this
workaround for the AQR113C phy found on revision C LS1046ARDB boards.
Fixes: 12cf1b89a6 ("net: phy: Add support for AQR113C EPHY")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220818164029.2063293-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Code reimplements functionality already in `fec_ptp_read()`,
but misses check for FEC_QUIRK_BUG_CAPTURE. Replace with function call.
Fixes: 28b5f058cf ("net: fec: ptp: fix convergence issue to support LinuxPTP stack")
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Link: https://lore.kernel.org/r/20220811101348.13755-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A little longer PR than usual but it's all fixes, no late features.
It's long partially because of timing, and partially because of
follow ups to stuff that got merged a week or so before the merge
window and wasn't as widely tested. Maybe the Bluetooth fixes are
a little alarming so we'll address that, but the rest seems okay
and not scary.
Notably we're including a fix for the netfilter Kconfig [1], your
WiFi warning [2] and a bluetooth fix which should unblock syzbot [3].
Current release - regressions:
- Bluetooth:
- don't try to cancel uninitialized works [3]
- L2CAP: fix use-after-free caused by l2cap_chan_put
- tls: rx: fix device offload after recent rework
- devlink: fix UAF on failed reload and leftover locks in mlxsw
Current release - new code bugs:
- netfilter:
- flowtable: fix incorrect Kconfig dependencies [1]
- nf_tables: fix crash when nf_trace is enabled
- bpf:
- use proper target btf when exporting attach_btf_obj_id
- arm64: fixes for bpf trampoline support
- Bluetooth:
- ISO: unlock on error path in iso_sock_setsockopt()
- ISO: fix info leak in iso_sock_getsockopt()
- ISO: fix iso_sock_getsockopt for BT_DEFER_SETUP
- ISO: fix memory corruption on iso_pinfo.base
- ISO: fix not using the correct QoS
- hci_conn: fix updating ISO QoS PHY
- phy: dp83867: fix get nvmem cell fail
Previous releases - regressions:
- wifi: cfg80211: fix validating BSS pointers in
__cfg80211_connect_result [2]
- atm: bring back zatm uAPI after ATM had been removed
- properly fix old bug making bonding ARP monitor mode not being
able to work with software devices with lockless Tx
- tap: fix null-deref on skb->dev in dev_parse_header_protocol
- revert "net: usb: ax88179_178a needs FLAG_SEND_ZLP" it helps
some devices and breaks others
- netfilter:
- nf_tables: many fixes rejecting cross-object linking
which may lead to UAFs
- nf_tables: fix null deref due to zeroed list head
- nf_tables: validate variable length element extension
- bgmac: fix a BUG triggered by wrong bytes_compl
- bcmgenet: indicate MAC is in charge of PHY PM
Previous releases - always broken:
- bpf:
- fix bad pointer deref in bpf_sys_bpf() injected via test infra
- disallow non-builtin bpf programs calling the prog_run command
- don't reinit map value in prealloc_lru_pop
- fix UAFs during the read of map iterator fd
- fix invalidity check for values in sk local storage map
- reject sleepable program for non-resched map iterator
- mptcp:
- move subflow cleanup in mptcp_destroy_common()
- do not queue data on closed subflows
- virtio_net: fix memory leak inside XDP_TX with mergeable
- vsock: fix memory leak when multiple threads try to connect()
- rework sk_user_data sharing to prevent psock leaks
- geneve: fix TOS inheriting for ipv4
- tunnels & drivers: do not use RT_TOS for IPv6 flowlabel
- phy: c45 baset1: do not skip aneg configuration if clock role
is not specified
- rose: avoid overflow when /proc displays timer information
- x25: fix call timeouts in blocking connects
- can: mcp251x: fix race condition on receive interrupt
- can: j1939:
- replace user-reachable WARN_ON_ONCE() with netdev_warn_once()
- fix memory leak of skbs in j1939_session_destroy()
Misc:
- docs: bpf: clarify that many things are not uAPI
- seg6: initialize induction variable to first valid array index
(to silence clang vs objtool warning)
- can: ems_usb: fix clang 14's -Wunaligned-access warning
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=C5Ck
-----END PGP SIGNATURE-----
Merge tag 'net-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf, can and netfilter.
A little larger than usual but it's all fixes, no late features. It's
large partially because of timing, and partially because of follow ups
to stuff that got merged a week or so before the merge window and
wasn't as widely tested. Maybe the Bluetooth fixes are a little
alarming so we'll address that, but the rest seems okay and not scary.
Notably we're including a fix for the netfilter Kconfig [1], your WiFi
warning [2] and a bluetooth fix which should unblock syzbot [3].
Current release - regressions:
- Bluetooth:
- don't try to cancel uninitialized works [3]
- L2CAP: fix use-after-free caused by l2cap_chan_put
- tls: rx: fix device offload after recent rework
- devlink: fix UAF on failed reload and leftover locks in mlxsw
Current release - new code bugs:
- netfilter:
- flowtable: fix incorrect Kconfig dependencies [1]
- nf_tables: fix crash when nf_trace is enabled
- bpf:
- use proper target btf when exporting attach_btf_obj_id
- arm64: fixes for bpf trampoline support
- Bluetooth:
- ISO: unlock on error path in iso_sock_setsockopt()
- ISO: fix info leak in iso_sock_getsockopt()
- ISO: fix iso_sock_getsockopt for BT_DEFER_SETUP
- ISO: fix memory corruption on iso_pinfo.base
- ISO: fix not using the correct QoS
- hci_conn: fix updating ISO QoS PHY
- phy: dp83867: fix get nvmem cell fail
Previous releases - regressions:
- wifi: cfg80211: fix validating BSS pointers in
__cfg80211_connect_result [2]
- atm: bring back zatm uAPI after ATM had been removed
- properly fix old bug making bonding ARP monitor mode not being able
to work with software devices with lockless Tx
- tap: fix null-deref on skb->dev in dev_parse_header_protocol
- revert "net: usb: ax88179_178a needs FLAG_SEND_ZLP" it helps some
devices and breaks others
- netfilter:
- nf_tables: many fixes rejecting cross-object linking which may
lead to UAFs
- nf_tables: fix null deref due to zeroed list head
- nf_tables: validate variable length element extension
- bgmac: fix a BUG triggered by wrong bytes_compl
- bcmgenet: indicate MAC is in charge of PHY PM
Previous releases - always broken:
- bpf:
- fix bad pointer deref in bpf_sys_bpf() injected via test infra
- disallow non-builtin bpf programs calling the prog_run command
- don't reinit map value in prealloc_lru_pop
- fix UAFs during the read of map iterator fd
- fix invalidity check for values in sk local storage map
- reject sleepable program for non-resched map iterator
- mptcp:
- move subflow cleanup in mptcp_destroy_common()
- do not queue data on closed subflows
- virtio_net: fix memory leak inside XDP_TX with mergeable
- vsock: fix memory leak when multiple threads try to connect()
- rework sk_user_data sharing to prevent psock leaks
- geneve: fix TOS inheriting for ipv4
- tunnels & drivers: do not use RT_TOS for IPv6 flowlabel
- phy: c45 baset1: do not skip aneg configuration if clock role is
not specified
- rose: avoid overflow when /proc displays timer information
- x25: fix call timeouts in blocking connects
- can: mcp251x: fix race condition on receive interrupt
- can: j1939:
- replace user-reachable WARN_ON_ONCE() with netdev_warn_once()
- fix memory leak of skbs in j1939_session_destroy()
Misc:
- docs: bpf: clarify that many things are not uAPI
- seg6: initialize induction variable to first valid array index (to
silence clang vs objtool warning)
- can: ems_usb: fix clang 14's -Wunaligned-access warning"
* tag 'net-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (117 commits)
net: atm: bring back zatm uAPI
dpaa2-eth: trace the allocated address instead of page struct
net: add missing kdoc for struct genl_multicast_group::flags
nfp: fix use-after-free in area_cache_get()
MAINTAINERS: use my korg address for mt7601u
mlxsw: minimal: Fix deadlock in ports creation
bonding: fix reference count leak in balance-alb mode
net: usb: qmi_wwan: Add support for Cinterion MV32
bpf: Shut up kern_sys_bpf warning.
net/tls: Use RCU API to access tls_ctx->netdev
tls: rx: device: don't try to copy too much on detach
tls: rx: device: bound the frag walk
net_sched: cls_route: remove from list when handle is 0
selftests: forwarding: Fix failing tests with old libnet
net: refactor bpf_sk_reuseport_detach()
net: fix refcount bug in sk_psock_get (2)
selftests/bpf: Ensure sleepable program is rejected by hash map iter
selftests/bpf: Add write tests for sk local storage map iterator
selftests/bpf: Add tests for reading a dangling map iter fd
bpf: Only allow sleepable program for resched-able iterator
...
We should trace the allocated address instead of page struct.
Fixes: 27c874867c ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20220811151651.3327-1-chen45464546@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are required by certain network profiling applications in order to
measure delays.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220629181335.3800821-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
Some resources are allocated using pci_request_region().
It is more straightforward to release them with pci_release_region().
Fixes: 231ece36f5 ("enetc: Add mdio bus driver for the PCIe MDIO endpoint")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts these files to use SPDX idenfifiers instead of license
text.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmap the Scatter/Gather table before going through the array to
unmap and free each of the header and data chunks. This is so we do not
touch the data between the dma_map and dma_unmap calls.
Fixes: 3dc709e0cd ("dpaa2-eth: add support for software TSO")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incorrect software annotation field was being used, swa->sg.sgt_size
instead of swa->tso.sgt_size, which meant that the SGT buffer was
unmapped with a wrong size.
This is also confirmed by the DMA API debug prints which showed the
following:
[ 38.962434] DMA-API: fsl_dpaa2_eth dpni.2: device driver frees DMA memory with different size [device address=0x0000fffffafba740] [map size=224 bytes] [unmap size=0 bytes]
[ 38.980496] WARNING: CPU: 11 PID: 1131 at kernel/dma/debug.c:973 check_unmap+0x58c/0x9b0
[ 38.988586] Modules linked in:
[ 38.991631] CPU: 11 PID: 1131 Comm: iperf3 Not tainted 5.18.0-rc7-00117-g59130eeb2b8f #1972
[ 38.999970] Hardware name: NXP Layerscape LX2160ARDB (DT)
Fixes: 3dc709e0cd ("dpaa2-eth: add support for software TSO")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error code returned by devm_clk_get() might have other meanings than
"This clock doesn't exist". So use devm_clk_get_optional() and handle
all remaining errors as fatal.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error code returned by devm_clk_get() might have other meanings than
"This clock doesn't exist". So use devm_clk_get_optional() and handle
all remaining errors as fatal.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle)
doesn't register with phylink, but calls netif_carrier_on() from
enetc_start().
This makes sense for a VF, but for a PF, this is braindead, because we
never call enetc_mac_enable() so the MAC is left inoperational.
Furthermore, commit 71b77a7a27 ("enetc: Migrate to PHYLINK and
PCS_LYNX") put the nail in the coffin because it removed the initial
netif_carrier_off() call done right after register_netdev().
Without that call, netif_carrier_on() does not call
linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN.
Just deny the broken configuration by requiring that a phy-mode is
present, and always register a PF with phylink.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The enetc scheduler for IEEE 802.1Qbv has 2 options (depending on
PTGCR[TG_DROP_DISABLE]) when we attempt to send an oversized packet
which will never fit in its allotted time slot for its traffic class:
either block the entire port due to head-of-line blocking, or drop the
packet and set a bit in the writeback format of the transmit buffer
descriptor, allowing other packets to be sent.
We obviously choose the second option in the driver, but we do not
detect the drop condition, so from the perspective of the network stack,
the packet is sent and no error counter is incremented.
This change checks the writeback of the TX BD when tc-taprio is enabled,
and increments a specific ethtool statistics counter and a generic
"tx_dropped" counter in ndo_get_stats64.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Future work in this driver would like to look at priv->active_offloads &
ENETC_F_QBV to determine whether a tc-taprio qdisc offload was
installed, but this does not produce the intended effect.
All the other flags in priv->active_offloads are managed dynamically,
except ENETC_F_QBV which is set statically based on the probed SI capability.
This change makes priv->active_offloads & ENETC_F_QBV really track the
presence of a tc-taprio schedule on the port.
Some existing users, like the enetc_sched_speed_set() call from
phylink_mac_link_up(), are best kept using the old logic: the tc-taprio
offload does not re-trigger another link mode resolve, so the scheduler
needs to be functional from the get go, as long as Qbv is supported at
all on the port. So to preserve functionality there, look at the static
station interface capability from pf->si->hw_features instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 4e30e98c4b ("dpaa2-mac: return -EPROBE_DEFER from dpaa2_mac_open in case the fwnode is not set")
@parent can't be NULL after the if. It's either the address
of the ->fwnode of @dpmacs or @fwnode in case of ACPI.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220506200029.852310-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Switch all Ethernet drivers which use custom napi weights
to the new API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc's asm/prom.h includes some headers that it doesn't
need itself.
In order to clean powerpc's asm/prom.h up in a further step,
first clean all files that include asm/prom.h
Some files don't need asm/prom.h at all. For those ones,
just remove inclusion of asm/prom.h
Some files don't need any of the items provided by asm/prom.h,
but need some of the headers included by asm/prom.h. For those
ones, add the needed headers that are brought by asm/prom.h at
the moment and remove asm/prom.h
Some files really need asm/prom.h but also need some of the
headers included by asm/prom.h. For those one, leave asm/prom.h
but also add the needed headers so that they can be removed
from asm/prom.h in a later step.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/09a13d592d628de95d30943e59b2170af5b48110.1651663857.git.christophe.leroy@csgroup.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Time-Specified Departure feature is indeed mutually exclusive with
TX IP checksumming in ENETC, but TX checksumming in itself is broken and
was removed from this driver in commit 82728b91f1 ("enetc: Remove Tx
checksumming offload code").
The blamed commit declared NETIF_F_HW_CSUM in dev->features to comply
with software TSO's expectations, and still did the checksumming in
software by calling skb_checksum_help(). So there isn't any restriction
for the Time-Specified Departure feature.
However, enetc_setup_tc_txtime() doesn't understand that, and blindly
looks for NETIF_F_CSUM_MASK.
Instead of checking for things which can literally never happen in the
current code base, just remove the check and let the driver offload
tc-etf qdiscs.
Fixes: acede3c5da ("net: enetc: declare NETIF_F_HW_CSUM and do it in software")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220427203017.1291634-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both of of_get_parent() and of_parse_phandle() return node pointer with
refcount incremented, use of_node_put() on it to decrease refcount
when done.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This node pointer is returned by of_find_compatible_node() with
refcount incremented. Calling of_node_put() to aovid the refcount leak.
Fixes: d346c9e86d ("dpaa2-ptp: reuse ptp_qoriq driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404125336.13427-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Let user space properly determine that the enetc driver provides
software timestamps.
Fixes: 4caefbce06 ("enetc: add software timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220324161210.4122281-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
Hi Linus,
Please, pull the following treewide patch that replaces zero-length arrays with
flexible-array members. This patch has been baking in linux-next for a
whole development cycle.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=xZD2
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull flexible-array transformations from Gustavo Silva:
"Treewide patch that replaces zero-length arrays with flexible-array
members.
This has been baking in linux-next for a whole development cycle"
* tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
treewide: Replace zero-length arrays with flexible-array members
When compiling with -Wformat, clang emits the following warning:
drivers/net/ethernet/freescale/xgmac_mdio.c:243:22: warning: format
specifies type 'unsigned char' but the argument has type 'int'
[-Wformat]
phy_id, dev_addr, regnum);
^~~~~~
./include/linux/dev_printk.h:163:47: note: expanded from macro 'dev_dbg'
dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:129:34: note: expanded from macro 'dev_printk'
_dev_printk(level, dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Link: https://lore.kernel.org/r/20220316213114.2352352-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with -Wformat, clang emits the following warning:
drivers/net/ethernet/freescale/enetc/enetc_mdio.c:151:22: warning:
format specifies type 'unsigned char' but the argument has type 'int'
[-Wformat]
phy_id, dev_addr, regnum);
^~~~~~
./include/linux/dev_printk.h:163:47: note: expanded from macro 'dev_dbg'
dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:129:34: note: expanded from macro 'dev_printk'
_dev_printk(level, dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220316213109.2352015-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch integrates the dpaa2-eth driver with the generic PHY
infrastructure in order to search, find and reconfigure the SerDes lanes
in case of a protocol change.
On the .mac_config() callback, the phy_set_mode_ext() API is called so
that the Lynx 28G SerDes PHY driver can change the lane's configuration.
In the same phylink callback the MC firmware is called so that it
reconfigures the MAC side to run using the new protocol.
The consumer drivers - dpaa2-eth and dpaa2-switch - are updated to call
the dpaa2_mac_start/stop functions newly added which will
power_on/power_off the associated SerDes lane.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to setup the supported interfaces will get annotated based on
what the configuration of the SerDes PLLs supports. Move the current
setup into a separate function just to try to keep it clean.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the API version running on the firmware and based on it detect
which features are available for usage.
The first one to be listed is the capability to change the MAC protocol
at runtime.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC firmware gained recently a new command which can reconfigure the
running protocol on the underlying MAC. Add this new command which will
be used in the next patches in order to do a major reconfig on the
interface.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpmac_get_api_version command will be used in the next patches to
determine if the current firmware is capable or not to change the
Ethernet protocol running on the MAC.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 7349a74ea7 ("net: ethernet: gianfar_ethtool: get phc index through drvdata")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220310015313.14938-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPAA2 MAC supports 1588 one step timestamping.
If this option is enabled then for each transmitted PTP event packet,
the 1588 SINGLE_STEP register is accessed to modify the following fields:
-offset of the correction field inside the PTP packet
-UDP checksum update bit, in case the PTP event packet has
UDP encapsulation
These values can change any time, because there may be multiple
PTP clients connected, that receive various 1588 frame types:
- L2 only frame
- UDP / Ipv4
- UDP / Ipv6
- other
The current implementation uses dpni_set_single_step_cfg to update the
SINLGE_STEP register.
Using an MC command on the Tx datapath for each transmitted 1588 message
introduces high delays, leading to low throughput and consequently to a
small number of supported PTP clients. Besides these, the nanosecond
correction field from the PTP packet will contain the high delay from the
driver which together with the originTimestamp will render timestamp
values that are unacceptable in a GM clock implementation.
This patch updates the Tx datapath for 1588 messages when single step
timestamp is enabled and provides direct access to SINGLE_STEP register,
eliminating the overhead caused by the dpni_set_single_step_cfg
MC command. MC version >= 10.32 implements this functionality.
If the MC version does not have support for returning the
single step register base address, the driver will use
dpni_set_single_step_cfg command for updates operations.
All the delay introduced by dpni_set_single_step_cfg
function will be eliminated (if MC version has support for returning the
base address of the single step register), improving the egress driver
performance for PTP packets when single step timestamping is enabled.
Before these changes the maximum throughput for 1588 messages with
single step hardware timestamp enabled was around 2000pps.
After the updates the throughput increased up to 32.82 Mbps / 46631.02 pps.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dpni_get_single_step_cfg is an MC firmware command used for
retrieving the contents of SINGLE_STEP 1588 register available
in a DPMAC.
This patch adds a new version of this command that returns as an extra
argument the physical base address of the aforementioned register.
The address will be used to directly modify the contents of the
SINGLE_STEP register instead of invoking the MC command
dpni_set_single_step_cgf. The former approach introduced huge delays on
the TX datapath when one step PTP events were transmitted. This led to low
throughput and high latencies observed in the PTP correction field.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Fix the following coccicheck warnings:
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1199:42-47: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1218:54-59: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1588 Single Step Timestamping code path uses a mutex to
enforce atomicity for two events:
- update of ptp single step register
- transmit ptp event packet
Before this patch the mutex was not initialized. This
caused unexpected crashes in the Tx function.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang static analysis reports this representative problem
dpaa2-switch-flower.c:616:24: warning: The right operand of '=='
is a garbage value
tmp->cfg.vlan_id == vlan) {
^ ~~~~
vlan is set in dpaa2_switch_flower_parse_mirror_key(). However
this function can return success without setting vlan. So
change the default return to -EOPNOTSUPP.
Fixes: 0f3faece58 ("dpaa2-switch: add VLAN based mirroring")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev should be unregistered before we are disconnecting from the
MAC/PHY so that the dev_close callback is called and the PHY and the
phylink workqueues are actually stopped before we are disconnecting and
destroying the phylink instance.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can use the enetc_cbd_alloc_data_mem() to replace complicated DMA
data alloc method and CBDR memory basic seting.
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the CBDR data memory alloc standalone. It is convenient for
other part loading, for example the ENETC QOS part.
Reported-and-suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To replace the dma_map_single() stream DMA mapping with DMA coherent
method dma_alloc_coherent() which is more simple.
dma_map_single() found by Tim Gardner not proper. Suggested by Claudiu
Manoil and Jakub Kicinski to use dma_alloc_coherent(). Discussion at:
https://lore.kernel.org/netdev/AM9PR04MB8397F300DECD3C44D2EBD07796BD9@AM9PR04MB8397.eurprd04.prod.outlook.com/t/
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for driver level TSO in the enetc driver using
the TSO API.
There is not much to say about this specific implementation. We are
using the usual tso_build_hdr(), tso_build_data() to create each data
segment, we create an array of S/G FDs where the first S/G entry is
referencing the header data and the remaining ones the data portion.
For the S/G Table buffer we use the same cache of buffers used on the
other non-GSO cases - dpaa2_eth_sgt_get() and dpaa2_eth_sgt_recycle().
We cannot keep a DMA coherent buffer for all the TSO headers because the
DPAA2 architecture does not work in a ring based fashion so we just
allocate a buffer each time.
Even with these limitations we get the following improvement in TCP
termination on the LX2160A SoC, on a single A72 core running at 2.2GHz.
before: 6.38Gbit/s
after: 8.48Gbit/s
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the __dpaa2_eth_tx function used a single FD on the stack
to construct the structure to be enqueued. Since we are now preparing
the ground work to add support for TSO done in software at the driver
level, the same function needs to work with an array of FDs and enqueue
as many as the build_*_fd functions create.
Make the necessary adjustments in order to do this. These include:
keeping an array of FDs in a percpu structure, cleaning up the necessary
FDs before populating it and then, retrying the enqueue process up till
all the generated FDs were enqueued or until we reach the maximum number
retries.
This patch does not change the fact that only a single FD will result
from a __dpaa2_eth_tx call but rather just creates the necessary changes
for the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating memory for an S/G table each time a nonlinear skb
is processed, and then freeing it on the Tx confirmation path, use the
S/G table cache in order to reuse the memory.
For this to work we have to change the size of the cached buffers so
that it can hold the maximum number of scatterlist entries.
Other than that, each allocate/free call is replaced by a call to the
dpaa2_eth_sgt_get/dpaa2_eth_sgt_recycle functions, introduced in the
previous patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver uses in certain circumstances a buffer cache for
the S/G tables needed in case of a S/G FD. At the moment, the
interraction with the cache is open-coded and couldn't be reused easily.
Add two new functions - dpaa2_eth_sgt_get and dpaa2_eth_sgt_recycle -
which help with code reusability.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating memory and then manually aligning it to the
desired value use napi_alloc_frag_align() directly to streamline the
process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we'll be moving things arroung in the mentioned
function and also add some new variable declarations. Before all this,
cleanup the variable declaration order.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: 1d14eb15dc ("net/fsl: xgmac_mdio: Use managed device resources")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the standard "clock-frequency" attribute to set the generated
MDC frequency. If not specified, the driver will leave the divisor
bits untouched.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the standard "suppress-preamble" attribute to disable preamble
generation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the resources used by this driver has managed interfaces, so
use them. Heed the warning in the comment before platform_get_resource
and use a bare devm_ioremap to allow for non-exclusive access to the
IO memory.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dpaa2-mac to use the mac_select_pcs() interface rather than
using phylink_set_pcs(). The intention here is to unify the approach
for PCS and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes made netdev->dev_addr const, and it's passed
directly to mpc52xx_fec_set_paddr().
Similar problem exists on the probe patch, the driver needs
to call eth_hw_addr_set().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: adeef3e321 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2nd param of phy_init_eee(): clk_stop_enable is a bool param, use
true or false instead of 1/0.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220123152241.1480-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable val is being initialized with a value that is never read,
it is being re-assigned later. The assignment is redundant and
can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20220123184936.113486-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers,
read the right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XM4Y
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf.
Quite a handful of old regression fixes but most of those are
pre-5.16.
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers, read the
right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885"
* tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys
ipv4: avoid quadratic behavior in netns dismantle
net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module
powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses
dt-bindings: net: Document fsl,erratum-a009885
net/fsl: xgmac_mdio: Add workaround for erratum A-009885
net: mscc: ocelot: fix using match before it is set
net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices
net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind()
net: axienet: increase default TX ring size to 128
net: axienet: fix for TX busy handling
net: axienet: fix number of TX ring slots for available check
net: axienet: Fix TX ring slot available check
net: axienet: limit minimum TX ring size
net: axienet: add missing memory barriers
net: axienet: reset core on initialization prior to MDIO access
net: axienet: Wait for PhyRstCmplt after core reset
net: axienet: increase reset timeout
bpf, selftests: Add ringbuf memory type confusion test
...
As reported by sparse: In the remove path, the driver would attempt to
unmap its own priv pointer - instead of the io memory that it mapped
in probe.
Fixes: 9f35a7342c ("net/fsl: introduce Freescale 10G MDIO driver")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once an MDIO read transaction is initiated, we must read back the data
register within 16 MDC cycles after the transaction completes. Outside
of this window, reads may return corrupt data.
Therefore, disable local interrupts in the critical section, to
maximize the probability that we can satisfy this requirement.
Fixes: d55ad2967d ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
Before accessing the port private structure make sure that there is
still a non-NULL pointer there. A NULL pointer access can happen when we
are on the remove path, some switch ports are unregistered and some are
in the process of unregistering.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We could get into a situation when the fwnode of the parent device is
not yet set because its probe didn't yet finish. When this happens, any
caller of the dpaa2_mac_open() will not have the fwnode available, thus
cause problems at the PHY connect time.
Avoid this by just returning -EPROBE_DEFER from the dpaa2_mac_open when
this happens.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parent pointer node handler must be declared with a NULL
initializer. Before using it, a check must be performed to make
sure that a valid address has been assigned to it.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 26eee0210a ("net/fsl: fix a bug in xgmac_mdio") fixed a bug in
the QorIQ mdio driver but left the (now unused) incorrect bit definition
for MDIO_DATA_BSY in the code. This commit removes it.
Signed-off-by: Markus Koch <markus@notsyncing.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq(). While doing so return error pointer
from read_dts_node() as platform_get_irq() may return -EPROBE_DEFER.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing a pointer to the MSI descriptor just to track the Linux interrupt
number is daft. Just store the interrupt number and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221815.207838579@linutronix.de
Unfortunately, with the blamed commit I also added a side effect in the
ethtool stats shown. Because I added two more fields in the per channel
structure without verifying if its size is used in any way, part of the
ethtool statistics were off by 2.
Fix this by not looking up the size of the structure but instead on a
fixed value kept in a macro.
Fixes: fc398bec03 ("net: dpaa2: add adaptive interrupt coalescing")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211215105831.290070-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1. During normal suspend (WoL not enabled) process, system has posibility
to hang. The root cause is TXF interrupt coming after clocks disabled,
system hang when accessing registers from interrupt handler. To fix this
issue, disable all interrupts when system suspend.
2. System also has posibility to hang with WoL enabled during suspend,
after entering stop mode, then magic pattern coming after clocks
disabled, system will be waked up, and interrupt handler will be called,
system hang when access registers. To fix this issue, disable wakeup
irq in .suspend(), and enable it in .resume().
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit c55211892f ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPAA2 has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy interface mode bitmap for the Freescale DPAA2 driver
with interfaces modes supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it.
Fixes: 7472dd9f64 ("staging: fsl-dpaa2/eth: Move print message")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Freescale enetc driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code checks whether the skb had one-step TX timestamping enabled, in
order to schedule the work item for emptying the priv->tx_skbs queue.
That code checks for "tx_swbd->skb" directly, when we already had a skb
retrieved using enetc_tx_swbd_get_skb(tx_swbd) - a TX software BD can
also hold an XDP_TX packet or an XDP frame. But since the direct tx_swbd
dereference is in an "if" block guarded by the non-NULL quality of
"skb", accessing "tx_swbd->skb" directly is not wrong, just confusing.
Just use the local variable named "skb".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "priv" variable is needed in the "check_writeback" scope since
commit d398231219 ("enetc: add hardware timestamping support").
Since commit 7294380c52 ("enetc: support PTP Sync packet one-step
timestamping"), we also need "priv" in the larger function scope.
So the local variable from the "if" block scope is not needed, and
actually shadows the other one. Delete it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enetc driver does not implement .ndo_change_mtu, instead it
configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU]
statically to a large value during probe time.
The driver used to configure only the max SDU for traffic class 0, and
that was fine while the driver could only use traffic class 0. But with
the introduction of mqprio, sending a large frame into any other TC than
0 is broken.
This patch fixes that by replicating per traffic class the static
configuration done in enetc_configure_port_mac().
Fixes: cbe9e83594 ("enetc: Enable TC offloading with mqprio")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two counters named "MAC tx frames", one of them is actually
incorrect. The correct name for that counter should be "MAC tx error
frames", which is symmetric to the existing "MAC rx error frames".
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coverity complains of a possible dereference of a null return value.
5. returned_null: kzalloc returns NULL. [show details]
6. var_assigned: Assigning: si_data = NULL return value from kzalloc.
488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
489 cbd.length = cpu_to_le16(data_size);
490
491 dma = dma_map_single(&priv->si->pdev->dev, si_data,
492 data_size, DMA_FROM_DEVICE);
While this kzalloc() is unlikely to fail, I did notice that the function
returned without unmapping si_data.
Fix this by refactoring the error paths and checking for kzalloc()
failure.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Pass a netdev into the helper instead of just the address,
read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adaptive interrupt coalescing to the dpaa2-eth driver.
First of all, ETHTOOL_COALESCE_USE_ADAPTIVE_RX is defined as a supported
coalesce parameter and the requested state is configured through the
dpio APIs added in the previous patch.
Besides the ethtool API interaction, we keep track of how many bytes and
frames are dequeued per CDAN (Channel Data Availability Notification)
and update the Net DIM instance through the dpaa2_io_update_net_dim()
API.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly exported dpio driver API to manually configure the IRQ
coalescing parameters requested by the user.
The .get_coalesce() and .set_coalesce() net_device callbacks are
implemented and directly export or setup the rx-usecs on all the
channels configured.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was supposed to be a check for if dma_alloc_coherent() failed
but it has a copy and paste bug so it will not work.
Fixes: fb8629e2cb ("net: enetc: add support for software TSO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211013080456.GC6010@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For those architectures which do not define_HAVE_ARCH_IPV6_CSUM, we need
to include ip6_checksum.h which provides the csum_ipv6_magic() function.
Fixes: fb8629e2cb ("net: enetc: add support for software TSO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211012121358.16641-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for driver level TSO in the enetc driver using
the TSO API.
Beside using the usual tso_build_hdr(), tso_build_data() this specific
implementation also has to compute the checksum, both IP and L4, for
each resulted segment. This is because the ENETC controller does not
support Tx checksum offload which is needed in order to take advantage
of TSO.
With the workaround for the ENETC MDIO erratum in place the Tx path of
the driver is forced to lock/unlock for each skb sent. This is why, even
though we are computing the checksum by hand we see the following
improvement in TCP termination on the LS1028A SoC, on a single A72 core
running at 1.3GHz:
before: 1.63 Gbits/sec
after: 2.34 Gbits/sec
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a preparation patch for software TSO in the enetc driver.
Unfortunately, ENETC does not support Tx checksum offload which would
normally render TSO, even software, impossible.
Declare NETIF_F_HW_CSUM as part of the feature set and do it at driver
level using skb_csum_hwoffload_help() so that we can move forward and
also add support for TSO in the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update three drivers to use the new phylink_set_10g_modes() helper:
Cadence macb, Freescale DPAA2 and Marvell PP2.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move devlink_register to be the last command in the initialization
sequence.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: c76a97218d ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink documentation says:
Note that the PHY may be able to transform from one connection
technology to another, so, eg, don't clear 1000BaseX just
because the MAC is unable to BaseX mode. This is more about
clearing unsupported speeds and duplex settings. The port modes
should not be cleared; phylink_set_port_modes() will help with this.
So add the missing 10G modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d16 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy should not be used because it doesn't limit the source
length. As linus says, it's a completely useless function if you
can't implicitly trust the source string - but that is almost always
why people think they should use it! All in all the BSD function
will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, We prefer using strscpy instead of strlcpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when probing returns an error, the netdev is freed but
phylink_disconnect is not called.
Create a common function between the unbind path and the error path,
call it the opposite of dpaa2_switch_probe_port: dpaa2_switch_remove_port,
and call it from both the unbind and the error path.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an ASSERT_RTNL in phylink_disconnect_phy which triggers
whenever dpaa2_switch_port_disconnect_mac is called.
To follow the pattern established by dpaa2_eth_disconnect_mac, take the
rtnl_mutex every time we call dpaa2_switch_port_disconnect_mac.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.
A sketch of what dpaa2_switch_init does:
dpsw_open
dpaa2_switch_detect_features
dpsw_reset
for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
dpsw_if_disable
dpsw_if_set_stp
dpsw_vlan_remove_if_untagged
dpsw_if_set_tci
dpsw_vlan_remove_if
}
dpsw_vlan_remove
alloc_ordered_workqueue
dpsw_fdb_remove
dpaa2_switch_ctrl_if_setup
When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.
Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.
This will trigger a second error:
[ 93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed
[ 93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13
[ 93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13
Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:
[E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled
So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.
Fixes: 613c0a5810 ("staging: dpaa2-switch: enable the control interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The menuconfig FSL_DPAA_ETH selects config FSL_FMAN_MAC, but the config
FSL_FMAN_MAC never existed in the kernel tree.
Hence, ./scripts/checkkconfigsymbols.py warns:
FSL_FMAN_MAC
Referencing files: drivers/net/ethernet/freescale/dpaa/Kconfig
Remove this dead select in menuconfig FSL_DPAA_ETH.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default FEC driver treat irq[0] (i.e. int0 described in dt-binding) as
wakeup interrupt, but this situation changed on i.MX8M serials, SoC
integration guys mix wakeup interrupt signal into int2 interrupt line.
This patch introduces FEC_QUIRK_WAKEUP_FROM_INT2 to indicate int2 as wakeup
interrupt for i.MX8MQ.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210812070948.25797-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a switch port is connected to a MAC, use the common dpaa2-mac support
for exporting the available MAC statistics.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patch, we'll add support for also exporting the MAC
statistics in the ethtool stats. Annotate already present HW stats with
a suggestive prefix.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate the common MAC endpoint management support into the
dpaa2-switch driver as well. Nothing special happens here, just that the
already available dpaa2-mac functions are also called from dpaa2-switch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a switch DPAA2 object, the interface ID is also needed when
querying for the object endpoint. Extend fsl_mc_get_endpoint() so that
users can also pass the interface ID that are interested in.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to dpaa2_switch_port_link_state_update is a leftover from the
time when on DPAA2 platforms the PHYs were started at boot time so when
an ifconfig was issued on the associated interface, the link status
needed to be checked directly from the ndo_open() callback. This is not
needed anymore since we are now properly integrated with the PHY layer
thus a link interrupt will come directly from the PHY eventually without
the need to call the sync function.
Fix this up by removing the call to dpaa2_switch_port_link_state_update.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not enable the switch interfaces at probe time since this is
trigged by the open callback. Remove the call dpsw_enable() which does
exactly this.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC firmware supplies us the switch interface index for which an
interrupt was triggered. Use this to our advantage instead of looping
through all the switch ports and doing unnecessary work.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request all interrupt sources to be read and then cleared on the DPSW
object. In the next patches we'll also add support for treating other
interrupts.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intends to fix MAC internal delay doesn't work, due to use
of_property_read_u32() incorrectly, and improve this feature a bit:
1) check the delay value if valid, only program register when it's 2000ps.
2) only enable "enet_2x_txclk" clock when require MAC internal delay.
Fixes: fc539459e9 ("net: fec: add MAC internal delayed clock feature support")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210803052424.19008-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the array faf_bits on the stack but instead it
static const. Makes the object code smaller by 175 bytes.
Before:
text data bss dec hex filename
9645 4552 0 14197 3775 ../freescale/dpaa2/dpaa2-eth-devlink.o
After:
text data bss dec hex filename
9406 4616 0 14022 36c6 ../freescale/dpaa2/dpaa2-eth-devlink.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210801152209.146359-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When mirroring rules are added in shared filter blocks, the same
mirroring rule has to be configured on all the switch ports that are
part of the same block.
In case a switch port joins a shared block after mirroring filters have
been already added to it, then all the mirror rules should be offloaded
to the port. The reverse, removal of mirroring rules, has to be done at
block unbind.
For this purpose, the dpaa2_switch_block_offload_mirror() and
dpaa2_switch_block_unoffload_mirror() functions are added and called
upon binding and unbinding a switch port to/from a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the infrastructure added in the previous patch, extend tc-flower
support with FLOW_ACTION_MIRRED based on VLAN.
Tested with:
tc qdisc add dev eth8 ingress_block 1 clsact
tc filter add block 1 ingress protocol 802.1q flower skip_sw \
vlan_id 100 action mirred egress mirror dev eth6
tc filter del block 1 ingress pref 49152
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per port mirroring for the DPAA2 switch. We support
only single mirror port, therefore we allow mirroring rules only as long
as the destination port is always the same.
Unlike all the actions (drop, redirect, trap) already supported by the
dpaa2-switch driver, adding mirroring filters in shared blocks is not
achieved by a singular ACL entry added in a table shared by the ports.
This is why, when a new mirror filter is added in a block we have to got
through all the switch ports sharing it and configure the filter
individually on all.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary MC API for setting up and configuring the mirroring
feature on the DPSW DPAA2 object.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_matchall_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_flower_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, shared filter blocks were implemented only by ACL tables
shared between ports. Going forward, when the mirroring support will be
added, this will not be true anymore.
Rename the dpaa2_switch_acl_tbl into dpaa2_switch_filter_block so that
we make it clear that the structure is used not only for filters that
use the ACL table but will be used for all the filters that are added in
a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the dpaa2_switch_tc_parse_action() function was used for all
the supported tc actions since all of them were implemented by adding
ACL table entries. In the next commits, the dpaa2-switch driver will
gain mirroring support which is not using the same HW feature.
Make sure that we specify the ACL in the function name so that we make
it clear that it's only used for specific actions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX8QM ENET IP version support timing specification that MAC
integrate clock delay in RGMII mode, the delayed TXC/RXC as an
alternative option to work well with various PHYs.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8MQ ENET version support IEEE802.3az eee mode, add
eee mode tx lpi enable to support ethtool interface.
usage:
1. set sleep and wake timer to 5ms:
ethtool --set-eee eth0 eee on tx-lpi on tx-timer 5000
2. check the eee mode:
~# ethtool --show-eee eth0
EEE Settings for eth0:
EEE status: enabled - active
Tx LPI: 5000 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
Note: For realtime case and IEEE1588 ptp case, it should disable
EEE mode.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENET of imx8mq and imx8qm are basically the same as imx6sx,
but they have new features support based on imx6sx, like:
- imx8mq: supports IEEE 802.3az EEE standard.
- imx8qm: supports RGMII mode delayed clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
