On some devices the +5V Power pin of the HDMI connector and/or the ESD
protection logic is powered on by a separate regulator. Instead of
declaring this regulator as always-on, make hdmi-connector support the
additional hdmi-pwr supply.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230531000259.3758235-4-dmitry.baryshkov@linaro.org
In preparation to adding support for the hdmi_pwr supply, rename dp_pwr
structure field to the generic connector_pwr.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230531000259.3758235-3-dmitry.baryshkov@linaro.org
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526090709.1517297-1-u.kleine-koenig@pengutronix.de
The high-speed clock is hard-coded to the burst-clock
frequency specified in the device tree. However, when
using devices like certain bridge chips without burst mode
and varying resolutions and refresh rates, it may be
necessary to set the high-speed clock dynamically based
on the desired pixel clock for the connected device.
This also removes the need to set a clock speed from
the device tree for non-burst mode operation, since the
pixel clock rate is the rate requested from the attached
device like a bridge chip. This should have no impact
for people using burst-mode and setting the burst clock
rate is still required for those users. If the burst
clock is not present, change the error message to
dev_info indicating the clock use the pixel clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-7-aford173@gmail.com
The DPHY timings are currently hard coded. Since the input
clock can be variable, the phy timings need to be variable
too. To facilitate this, we need to cache the hs_clock
based on what is generated from the PLL.
The phy_mipi_dphy_get_default_config_for_hsclk function
configures the DPHY timings in pico-seconds, and a small macro
converts those timings into clock cycles based on the hs_clk.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-6-aford173@gmail.com
In order to support variable DPHY timings, it's necessary
to enable GENERIC_PHY_MIPI_DPHY so phy_mipi_dphy_get_default_config
can be used to determine the nominal values for a given resolution
and refresh rate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-5-aford173@gmail.com
Make the pll-clock-frequency optional. If it's present, use it
to maintain backwards compatibility with existing hardware. If it
is absent, read clock rate of "sclk_mipi" to determine the rate.
Since it can be optional, change the message from an error to
dev_info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-4-aford173@gmail.com
According to Table 13-45 of the i.MX8M Mini Reference Manual, the min
and max values for M and the frequency range for the VCO_out
calculator were incorrect. This information was contradicted in other
parts of the mini, nano and plus manuals. After reaching out to my
NXP Rep, when confronting him about discrepencies in the Nano manual,
he responded with:
"Yes it is definitely wrong, the one that is part
of the NOTE in MIPI_DPHY_M_PLLPMS register table against PMS_P,
PMS_M and PMS_S is not correct. I will report this to Doc team,
the one customer should be take into account is the Table 13-40
DPHY PLL Parameters and the Note above."
These updated values also match what is used in the NXP downstream
kernel.
To fix this, make new variables to hold the min and max values of m
and the minimum value of VCO_out, and update the PMS calculator to
use these new variables instead of using hard-coded values to keep
the backwards compatibility with other parts using this driver.
Fixes: 4d562c70c4 ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-3-aford173@gmail.com
Scale the blanking packet sizes to match the ratio between HS clock
and DPI interface clock. The controller seems to do internal scaling
to the number of active lanes, so we don't take those into account.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-2-aford173@gmail.com
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
According to the documentation [1] the proper enable flow is:
1. Enable DSI link and keep data lanes in LP-11 (stop state)
2. Disable stop state to bring data lanes into HS mode
Currently we do this all at once within enable(), which doesn't
allow to meet the requirements of some downstream bridges.
To fix this we now enable the DSI in pre_enable() and force it
into stop state using the FORCE_STOP_STATE bit in the ESCMODE
register until enable() is called where we reset the bit.
We currently do this only for i.MX8M as Exynos uses a different
init flow where samsung_dsim_init() is called from
samsung_dsim_host_transfer().
[1] https://docs.kernel.org/gpu/drm-kms-helpers.html#mipi-dsi-bridge-operation
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-2-frieder@fris.de
This map was created from register map from datasheet (section 5.1.2).
Unused registers are stated by address, so they show up in debugfs as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516071949.375264-1-alexander.stein@ew.tq-group.com
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Implement support for DSI clock and data lane DN/DP polarity swap by
means of decoding 'lane-polarities' DT property. The controller does
support DN/DP swap of clock lane and all data lanes, the controller
does not support polarity swap of individual data lane bundles, add
a check which verifies all data lanes have the same polarity.
This has been validated on an imx8mm board that actually has the MIPI DSI
clock lanes inverted.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-2-festevam@gmail.com
There is no need to exclusively set the .owner member of the struct
device_driver when defining the platform_driver struct. The Linux core
takes care of setting the .owner member as part of the call to
module_platform_driver() helper function.
Issue identified using the platform_no_drv_owner.cocci Coccinelle
semantic patch as:
drivers/gpu/drm/bridge/samsung-dsim.c:1957:6-11: No need to set .owner here.
The core will do it.
No functional changes are intended.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZF9igb/nvL6GRBsq@yoga
Do not generate the HS front and back porch gaps, the HSA gap and
EOT packet, as these packets are not required. This makes the bridge
work with Samsung DSIM on i.MX8MM and i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403221233.500485-2-marex@denx.de
Do not generate the HS front and back porch gaps, the HSA gap and
EOT packet, as these packets are not required. This makes the bridge
work with Samsung DSIM on i.MX8MM and i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403221233.500485-1-marex@denx.de
Remove the unused phy_delay_nsk variable, before it was wrongly used
to compute some register value, the fixed computation is no longer using
it and therefore can be removed.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-10-francesco@dolcini.it
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
Correct computation of TXTAGOCNT register.
This register must be set to a value that ensure that the
TTA-GO period = (4 x TLPX)
with the actual value of TTA-GO being
4 x (TXTAGOCNT + 1) x (HSByteClk cycle)
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-8-francesco@dolcini.it
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
Correct computation of TCLK_ZEROCNT register.
This register must be set to a value that ensure that
(TCLK-PREPARECNT + TCLK-ZERO) > 300ns
with the actual value of (TCLK-PREPARECNT + TCLK-ZERO) being
(1 to 2) + (TCLK_ZEROCNT + 1)) x HSByteClkCycle + (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Correctly compute the PLL target frequency, the current formula works
correctly only when the input bus width is 24bit, actually to properly
compute the PLL target frequency what is relevant is the bits-per-pixel
on the DSI link.
No regression expected since the DSI format is currently hard-coded as
MIPI_DSI_FMT_RGB888.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
According to Toshiba documentation the PLL input clock after the divider
should be not less than 4MHz, fix the PLL parameters computation
accordingly.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
The address of a data structure member was determined before
a corresponding null pointer check in the implementation of
the function “receive_timing_debugfs_show”.
Thus avoid the risk for undefined behaviour by moving the assignment
for the variable “vid” behind the null pointer check.
This issue was detected by using the Coccinelle software.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/fa69384f-1485-142b-c4ee-3df54ac68a89@web.de
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Add atomic_get_input_bus_fmts() implementation, tc358768 has a parallel
RGB input interface with the actual bus format depending on the amount
of parallel input data lines.
Without this change when the tc358768 is used with less than 24bit the
color mapping is completely wrong.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330095941.428122-7-francesco@dolcini.it
This driver includes the deprecated OF GPIO header <linux/of_gpio.h>
yet fail to use symbols from it, so drop the include.
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220812205746.609107-2-mairacanal@riseup.net
This bridge doesn't actually implement HPD due to it being way too slow
but instead expects the panel driver to wait enough to assume HPD is
asserted. However some panels (such as the generic 'edp-panel') expect
the bridge to deal with the delay and pass maximum delay to the aux
instead.
In order to support such panels, add a dummy implementation of wait
that would just sleep the maximum delay and assume no failure has
happened.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230408082014.235425-1-nikita@trvn.ru
Backmerging drm-next to sync with msm tree. Resolves a conflict
between aperture-helper changes and msm's use of those interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
i.MX6SX has a single LVDS port and share a similar LDB_CTRL register layout
with i.MX8MP and i.MX93.
There is no LVDS CTRL register on the i.MX6SX, so only write to
this register on the appropriate SoCs.
Add support for the i.MX6SX LDB.
Tested on a imx6sx-sdb board with a Hannstar HSD100PXN1 LVDS panel
and also on a custom i.MX6SX-based board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404020129.509356-2-festevam@gmail.com
main pull request for v6.4
Core Display:
============
* Bugfixes for error handling during probe
* rework UBWC decoder programming
* prepare_commit cleanup
* bindings for SM8550 (MDSS, DPU), SM8450 (DP)
* timeout calculation fixup
* atomic: use drm_crtc_next_vblank_start() instead of our own
custom thing to calculate the start of next vblank
DP:
==
* interrupts cleanup
DPU:
===
* DSPP sub-block flush on sc7280
* support AR30 in addition to XR30 format
* Allow using REC_0 and REC_1 to handle wide (4k) RGB planes
* Split the HW catalog into individual per-SoC files
DSI:
===
* rework DSI instance ID detection on obscure platforms
GPU:
===
* uapi C++ compatibility fix
* a6xx: More robust gdsc reset
* a3xx and a4xx devfreq support
* update generated headers
* various cleanups and fixes
* GPU and GEM updates to avoid allocations which could trigger
reclaim (shrinker) in fence signaling path
* dma-fence deadline hint support and wait-boost
* a640 speedbin support
* a650 speedbin support
Conflicts in drivers/gpu/drm/msm/adreno/adreno_gpu.c:
Conflict between the 7fa5047a43 ("drm: Use of_property_present() for
testing DT property presence") and 9f251f9340 ("drm/msm/adreno: Use
OPP for every GPU generation"). The latter removed the of_ function
call outright, so I went with what's in the PR unchanged.
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvwuj5tabyW910+N-B=5kFNAC7QNYoQ=0xi3roBjQvFFQ@mail.gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The default hpd_wait_us in panel_edp.c is 2 seconds. This makes the
sleep time in the polling of _ps8640_wait_hpd_asserted become 200ms.
Change it to a constant 20ms to speed up the function.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230331030204.1179524-1-treapking@chromium.org
Do not generate the HS front and back porch gaps, the HSA gap and
EOT packet, as per "SN65DSI83 datasheet SLLSEC1I - SEPTEMBER 2012
- REVISED OCTOBER 2020", page 22, these packets are not required.
This makes the TI SN65DSI83 bridge work with Samsung DSIM on i.MX8MN.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403190242.224490-1-marex@denx.de
The LDB driver currently checks whether dual mode is used, otherwise it
assumes only channel 0 is in use. Add support for using only channel 1. In
device tree terms, this means linking port 2 only.
Doing this cleanly requires changing the logic of the probe functions from
this:
1. use of_graph_get_remote_node() on port 1 to find the panel
2. use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode
to this:
1. use of_graph_get_remote_node() twice to find remote ports
2. reuse the result of the above to know whether each channel is enabled
and to find the panel
3. if (both channels as enabled)
use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode
Also add a dev_dbg() to log the detected mode and log an error in case no
panel was found (no channel enabled).
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405081058.2347130-2-luca.ceresoli@bootlin.com
There might be cases where the host attach is deferred, use dev_err_probe
to add more detailed information to /sys/kernel/debug/devices_deferred.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405075223.579461-1-alexander.stein@ew.tq-group.com
The TC358767/TC358867/TC9595 are capable of DSI burst mode, which
is more energy efficient than the non-burst modes. Make use of it.
The TC358767/TC358867/TC9595 are capable of DSI non-continuous clock,
since it sources the internal PLL clock from external clock source.
The DSI non-continuous clock further reduces power utilization.
The TC358767/TC358867/TC9595 may use DSI LPM for command transmissions,
make sure this is configured correctly in the DSI mode flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221016003632.406468-1-marex@denx.de
LT8912 DSI port supports only Non-Burst mode video operation with Sync
Events and continuous clock on clock lane, correct dsi mode flags
according to that removing MIPI_DSI_MODE_VIDEO_BURST flag.
Cc: <stable@vger.kernel.org>
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330093131.424828-1-francesco@dolcini.it
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230310144706.1542295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmQgu8QeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG2fAH/0+pSM+u9ZiTCRcc
9cxpHqRu4J16oDJVroxD5c95C8t6pqq8emla7OcPjEbt+2jijEmTVda6i4IpAscc
e8c3t4zonzIjxWQxukZ2iPb7rUAsDYjom9Y5NpHB5J4eJMEvrgiDo7MIBtvwECYp
SejOpecquUcpFF1JTsDqqUUKgt56A/F/9jNyC/3p31doHbUfQWwTAiEA60gXwjiV
DtFFwUlKivLgkTOgigL0MUCrKLpwKXfpBOAbbp5h+zkV/6yjBmkx/OViovsJfrwX
kauOPOA/bSLXby4YyHkIB3nUY7mu7KDJfkpy2KMvZkRnJkYYW1Gt3urf714KVo5G
dnjfrA8=
=q5sO
-----END PGP SIGNATURE-----
Merge v6.3-rc4 into drm-next
I just landed the fence deadline PR from Rob that a bunch of drivers
want/need to apply driver-specific patches. Backmerge -rc4 so that
they don't have to be stuck on -rc2 for no reason at all.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com> # i.MX bridge
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230310144705.1542207-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add extras to support i.MX8M Plus. The main change is the removal of
HS/VS/DE signal inversion in the LCDIFv3-DSIM glue logic, otherwise
the implementation of this IP in i.MX8M Plus is very much compatible
with the i.MX8M Mini/Nano one.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <m.szyprowski@samsung.com>
Samsung MIPI DSIM master can also be found in i.MX8M Mini/Nano SoC.
Add compatible and associated driver_data for it.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Samsung MIPI DSIM controller is common DSI IP that can be used in various
SoCs like Exynos, i.MX8M Mini/Nano.
In order to access this DSI controller between various platform SoCs,
the ideal way to incorporate this in the drm stack is via the drm bridge
driver.
We already have a consolidated code for supporting component and bridge
based DRM drivers, so keep the exynos component based code in existing
exynos_drm_dsi.c and move generic bridge code as part of samsung-dsim.c
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There are 2 banks on it6505, and when writing to different bank,
REG_BANK_SEL needs to be set to the targeted bank. The current code set
this additionally, which causes a race condition when a process is
writing bank 0 registers while another process set the bank to 1. Set
ranges in regmap config so the regmap API would handle the bank changes.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230327044804.3657551-1-hsinyi@chromium.org
drm_edid_read returns NULL on error, so feeding it directly into
drm_edid_duplicate may lead to NULL pointer dereference. Add a check to
guard this.
Fixes: 6a17b4d1b5 ("drm/bridge: ps8640: Add a cache for EDID")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230324035909.1727356-1-treapking@chromium.org
When there are multiple EDID reads, the bridge will be repeatedly
enabled and disabled. Add a cache for EDID to speed this up.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230315035508.2874915-2-treapking@chromium.org
Skip the drm_bridge_chain_pre_enable call when the bridge is already
pre_enabled. This make pre_enable and post_disable (thus
pm_runtime_get/put) symmetric.
Fixes: 46f206304d ("drm/bridge: ps8640: Rework power state handling")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230315035508.2874915-1-treapking@chromium.org
Returns EPROBE_DEFER when of_drm_find_bridge() fails, this is consistent
with what all the other DRM bridge drivers are doing and this is
required since the bridge might not be there when the driver is probed
and this should not be a fatal failure.
Cc: <stable@vger.kernel.org>
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Matheus Castello <matheus.castello@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230322143821.109744-1-francesco@dolcini.it
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221622511915615@zte.com.cn
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221621336645576@zte.com.cn
Merge drm-next into msm-next to pick up external clk and PM dependencies
for improved a6xx GPU reset sequence.
Signed-off-by: Rob Clark <robdclark@chromium.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-20-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-19-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-18-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-17-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-16-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-15-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-14-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-13-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-12-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-11-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-10-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-9-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-8-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-7-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-6-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-5-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-3-u.kleine-koenig@pengutronix.de
When dynamically switching lanes was removed, the intent of the code
was to check to make sure that higher speed items used 4 lanes, but
it had the unintended consequence of removing the slower speeds for
4-lane users.
This attempts to remedy this by doing a check to see that the
max frequency doesn't exceed the chip limit, and a second
check to make sure that the max bit-rate doesn't exceed the
number of lanes * max bit rate / lane.
Fixes: 9a0cdcd664 ("drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge")
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230319125524.58803-1-aford173@gmail.com
clang with W=1 reports
drivers/gpu/drm/bridge/sii9234.c:870:31: error:
unused function 'bridge_to_sii9234' [-Werror,-Wunused-function]
static inline struct sii9234 *bridge_to_sii9234(struct drm_bridge *bridge)
^
This static function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318002321.1675181-1-trix@redhat.com
drm-misc-next for v6.4-rc1:
Note: Only changes since pull request from 2023-02-23 are included here.
UAPI Changes:
- Convert rockchip bindings to YAML.
- Constify kobj_type structure in dma-buf.
- FBDEV cmdline parser fixes, and other small fbdev fixes for mode
parsing.
Cross-subsystem Changes:
- Add Neil Armstrong as linaro maintainer.
- Actually signal the private stub dma-fence.
Core Changes:
- Add function for adding syncobj dep to sched_job and use it in panfrost, v3d.
- Improve DisplayID 2.0 topology parsing and EDID parsing in general.
- Add a gem eviction function and callback for generic GEM shrinker
purposes.
- Prepare to convert shmem helper to use the GEM reservation lock instead of own
locking. (Actual commit itself got reverted for now)
- Move the suballocator from radeon and amdgpu drivers to core in preparation
for Xe.
- Assorted small fixes and documentation.
- Fixes to HPD polling.
- Assorted small fixes in simpledrm, bridge, accel, shmem-helper,
and the selftest of format-helper.
- Remove dummy resource when ttm bo is created, and during pipelined
gutting. Fix all drivers to accept a NULL ttm_bo->resource.
- Handle pinned BO moving prevention in ttm core.
- Set drm panel-bridge orientation before connector is registered.
- Remove dumb_destroy callback.
- Add documentation to GEM_CLOSE, PRIME_HANDLE_TO_FD, PRIME_FD_TO_HANDLE, GETFB2 ioctl's.
- Add atomic enable_plane callback, use it in ast, mgag200, tidss.
Driver Changes:
- Use drm_gem_objects_lookup in vc4.
- Assorted small fixes to virtio, ast, bridge/tc358762, meson, nouveau.
- Allow virtio KMS to be disabled and compiled out.
- Add Radxa 8/10HD, Samsung AMS495QA01 panels.
- Fix ivpu compiler errors.
- Assorted fixes to drm/panel, malidp, rockchip, ivpu, amdgpu, vgem,
nouveau, vc4.
- Assorted cleanups, simplifications and fixes to vmwgfx.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ac1f5186-54bb-02f4-ac56-907f5b76f3de@linux.intel.com
This change will handle the psr entry exit cases in the panel
bridge atomic callback functions. For example, the panel power
should not turn off if the panel is entering psr.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patchwork: https://patchwork.freedesktop.org/patch/524721/
Link: https://lore.kernel.org/r/1677774797-31063-4-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Use atomic variants for panel bridge callback functions such that
certain states like self-refresh can be accessed as part of
enable/disable sequence.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patchwork: https://patchwork.freedesktop.org/patch/524720/
Link: https://lore.kernel.org/r/1677774797-31063-3-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Set the "pre_enable_prev_first" as provided by commit 4fb912e5e1
("drm/bridge: Introduce pre_enable_prev_first to alter bridge init
order"). This should allow us to revert commit ec7981e6c6
("drm/msm/dsi: don't powerup at modeset time for parade-ps8640") and
commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to modeset
time").
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131141756.RFT.v2.1.I723a3761d57ea60c5dd754c144aed6c3b2ea6f5a@changeid
Removals:
- remove legacy dri1 drivers -
- i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so
that we don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements
-----BEGIN PGP SIGNATURE-----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=HQUi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"There are a bunch of changes all over in the usual places.
Highlights:
- habanalabs moves from misc to accel
- first accel driver for Intel VPU (Versatile Processing Unit)
inference engine
- dropped all the ancient legacy DRI1 drivers. I think it's been at
least 10 years since anyone has heard about these.
- Intel DG2 updates and prelim Meteorlake enablement
- etnaviv adds support for Versilicon NPU device (a GPU like engine
with inference accelerators)
Detailed summary:
Removals:
- remove legacy dri1 drivers: i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so that we
don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to
copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct
drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements"
* tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm: (1455 commits)
msm/fbdev: fix unused variable warning with clang.
drm/fb-helper: Remove drm_fb_helper_unprepare() from drm_fb_helper_fini()
dma-buf: make kobj_type structure constant
drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
drm/amd/display: disable SubVP + DRR to prevent underflow
drm/amd/display: Fail atomic_check early on normalize_zpos error
drm/amd/pm: avoid unaligned access warnings
drm/amd/display: avoid unaligned access warnings
drm/amd/display: Remove duplicate/repeating expressions
drm/amd/display: Remove duplicate/repeating expression
drm/amd/display: Make variables declaration inside ifdef guard
drm/amd/display: Fix excess arguments on kernel-doc
drm/amd/display: Add previously missing includes
drm/amd/amdgpu: Add function prototypes to headers
drm/amd/display: Add function prototypes to headers
drm/amd/display: Turn global functions into static
drm/amd/display: remove unused _calculate_degamma_curve function
drm/amd/display: remove unused func declaration from resource headers
drm/amd/display: unset initial value for tf since it's never used
drm/amd/display: camel case cleanup in color_gamma file
...
Commit 15b9ca1641 ("drm: Config orientation property if panel provides
it") added a helper to set the panel orientation early but only
connected this for drm_bridge_connector, which constructs a panel bridge
with DRM_BRIDGE_ATTACH_NO_CONNECTOR and creates the connector itself.
When the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is not specified and the
panel_bridge creates its own connector the orientation is not set unless
the panel does it in .get_modes which is too late and leads to a warning
splat from __drm_mode_object_add() because the device is already
registered.
Call the necessary function to set add the orientation property when the
connector is created so that it is available before the device is
registered.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120114313.2087015-1-john@metanate.com
Enable the drm bridge pre_enable_prev_first flag so that the
previous bridge pre_enable should be called first before the
pre_enable for the tc358764 bridge is called.
This makes sure that the previous bridge should be initialized
properly before the tc358764 bridge is powered up.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Same to i.MX8mp LDB, i.MX93 LDB is controlled by mediamix blk-ctrl
through LDB_CTRL and LVDS_CTRL registers. i.MX93 LDB supports only
one LVDS channel(channel 0) and it's LVDS_CTRL register bit1 is used
as LVDS_EN instead of CH1_EN. Add i.MX93 LDB support in the existing
i.MX8mp LDB bridge driver by adding i.MX93 LDB compatible string and
device data(to reflect different register offsets and LVDS_CTRL register
bit1 definition).
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123021449.969243-3-victor.liu@nxp.com
commit f77a066f4e ("ASoC: hdmi-codec: Allow playback and capture
to be disabled") added new no_i2s_playback/capture.
We need to zero clear HDMI pdata first, otherwise unexpected flag
will be added.
Fixes: f77a066f4e ("ASoC: hdmi-codec: Allow playback and capture to be disabled")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k01hlnqj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Backmerging into drm-misc-next to get DRM accelerator infrastructure,
which is required by ipuv driver.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Switch to gpiod_set_value_cansleep() in sii902x_reset().
This is relevant if the reset line is tied to a I2C GPIO
controller.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221228145704.939801-1-w.egorov@phytec.de
If the bridge is connected using both DSI ports, the driver should use
both of them all the time. Correct programming sequence to always use
dual-port mode if both dsi0 and dsi1 are connected.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-14-dmitry.baryshkov@linaro.org
The lt9611 bridge can support different modes, it makes no sense to list
them in the table. Drop the table and check the number of interfaces
using the fixed value.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-13-dmitry.baryshkov@linaro.org
Rework handling infoframes:
- Write full HDMI AVI infoframe instead of just fixing the VIC value
- Also send the HDMI Vendor Specific infoframe, as recommended by the
HDMI spec.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-12-dmitry.baryshkov@linaro.org
Attaching DVI sink to the lt9611 requires different setup. Fix the
register write to make the DVI displays sync onto the correct sync
pulse.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-10-dmitry.baryshkov@linaro.org
