A pinctrl handle is used to setup a pull-up on the stusb1600 IRQ pin (that
is open drain).
When in ANALOG state, no pull-up can be applied in the GPIO HW controller,
still the setting is done into the register. The pull-up is effective
currently, only when the GPIO IRQ is requested. The correct setting is to
use directly the GPIO, instead of ANALOG state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Clean useless spaces in uart4_idle_pins_a node.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add pull-up to USART3 and UART7 RX pins to allow loop tests between USART3
and UART7 on stm32mp15 DKx boards.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output.
stm32mp15-pinctrl.dtsi contained one pin state definition for the DCMI
interface, dcmi-0, AKA phandle dcmi_pins_a. This definition was
incompatible with the pins used on the Odyssey board, where:
- there are 8 data pins instead of 12,
- DCMI_HSYNC is available at PA4 instead of PH8,
- DCMI_D0 is at PC6 instead of PH9,
- DCMI_D3 is at PE1 instead of PH12,
- DCMI_D4 is at PE11 instead of PH14,
- DCMI_D5 is at PD3 instead of PI4,
- DCMI_D6 is at PE13 instead of PB8,
- DCMI_D7 is at PB9 instead of PE6.
Add the DCMI pins used on the Odyssey board as a new DCMI pin state
definition, dcmi-1, AKA phandle dcmi_pins_b.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a7 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add SDA/SCL pinmux lines for I2C6 on STM32MP1.
This support adds both in default and sleep states.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add "init" mux option for SDMMC1, where the CMD, CK, CKIN lines are not
configured, so they can be claimed as GPIOs early on in driver probe().
This is used for probing optional voltage level translator.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
This patch adds support for STUSB1600 USB Type-C port controller, used on
I2C4 on stm32mp15xx-dkx.
The default configuration on this board, on Type-C connector, is:
- Dual Power Role (DRP), so set power-role to "dual";
- Vbus limited to 500mA, so set typec-power-opmode to "default" (it means
500mA in USB 2.0).
typec-power-opmode is used to reconfigure the STUSB1600 advertising of
current capability when its NVM is not in line with the board layout.
On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN. So power
operation mode depends on the power supply used. To avoid any power
issues, it is better to limit Vbus to 500mA on this board.
ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and
signal is active low.
USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx
boards, so disconnection are not detected.
Without DWC2 usb-role-switch:
- if you unplug the USB cable from the Type-C port, you have to manually
disconnect the USB gadget:
echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
- Then you can plug the USB cable again in the Type-C port, and manually
reconnect the USB gadget:
echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4 at the right alphabetical place within stm32mp15-pinctrl
Fixes: 4fe663890a ("ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FMC EBI bus, this is used on DHCOM SoM
for the second ethernet and on the PDK2 devkit for SRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins
are not in BANK Z.
Fixes: 498a701498 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use tabs where possible and remove multiple blanks lines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Sleep pin configuration is refined for low power modes:
- "sleep" (no wakeup & console suspend enabled): put pins in analog state
to optimize power
- "idle" (wakeup capability): keep Rx pin in alternate function
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These pinctrl definitions will be used by Stinger96/IoTBox boards
from Shiratech.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for SPI2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for ADC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN1 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add new mux option for SAI2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add new mux option for LTDC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for SDMMC1_D123DIR direction pins, SDMMC2 pins 4..7,
and SDMMC3 pins PD5_SDMMC3_D2 and PD0_SDMMC3_CMD, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
a PMIC. The board has eMMC and a SD slot for storage and GbE
for both connectivity and power.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
While all sleep pinctrl group labels now follow a fixed naming scheme,
node _names_ for these groups don't:
- Some use ${dev}-[0-9], where the suffix is the normal group suffix + 1
- Some use ${dev}-sleep-[0-9], where suffix is the normal group suffix
- The <dc node uses ${dev}-[a-z]-[0-9], where the letter matches the
phandle and the number suffix is the normal group's suffix + 1
For uniformity, standardize on using ${dev}-[0-9]+ for all normal
pinctrl groups and ${dev}-sleep-[0-9]+ for all sleep pinctrl groups.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Some labels follow the *_sleep_pins_* naming scheme, but some also use
*_pins_sleep_*. Because most labels use the former and for uniformity
with variants like sdmmc1_b4_pins_a and sdmmc1_dir_pins_a, adopt the
*_sleep_pins_* scheme throughout.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinctrl definition for USB High-Speed OTG ID pin and USB Full-Speed OTG
DP and DM lines that can be used on stm32mp15.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinmux entry for SAI2A with alternative pin configuration.
This is useful in combination with sai2b_pins_b e.g. for codecs
like SGTL5000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
ETH_MDIO slew-rate should be set to "0" instead of "2".
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In order to cover the STM32MP15 SOCs family this commit updates pinctrl
file names (group definition and packages files).
This family includes: STM32MP151, STM32MP153 and STM32MP157.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
