There is no user of the linux/spi/pxa2xx_spi.h. Move its contents
to the drivers/spi/spi-pxa2xx.h.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kernel-doc complains about last_cs_index_mask not described, so add its
description.
spi.h:778: warning: Function parameter or struct member 'last_cs_index_mask' not described in 'spi_controller'
Fixes: 4d8ff6b099 ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240328223340.17159-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Fix kernel documentation and inclusion block, and dropping the size
of the num_chipselect.
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
A couple of cleanups against linux/spi/pxa2xx_spi.h.
I'm sending this as v3 to land in the SPI subsystem. Meanwhile I'm
preparing an update to make linux/spi/pxa2xx_spi.h private to the
subsystem (PXA2xx driver). But the second part will be presented later
on (likely after v6.9-rc1). That said, this can be routed either via
SoC tree or SPI, up to respective maintainers.
There are no more users of the deprecated is_dma_mapped in struct
spi_message so it can be removed.
References in documentation and comments are also removed.
A few similar checks if xfer->tx_dma or xfer->rx_dma are not NULL are
also removed since these are now guaranteed to be NULL because they
were previously set only if is_dma_mapped was true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No in-kernel users of struct rspi_plat_data. If required,
the software nodes should be used for such users. For now
just get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240325142118.3210915-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no use for whole 16-bit for the number of chip select pins.
Drop it to 8 bits.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240307195056.4059864-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is the only one user of the pxa2xx_set_spi_info(). Unexport it
and inline to the actual user.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://msgid.link/r/20240307195056.4059864-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no use for whole 16-bit for the number of chip select pins.
Drop it to 8 bits and reshuffle the data structure layout to avoid
unnecessary paddings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://msgid.link/r/20240308162920.46816-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
xilinx_spi.h is mnissing inclusion and forward declaration, add them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://msgid.link/r/20240308162920.46816-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While updating the data structure layout the kernel documentation
became outdated. Synchronize kernel documentation with the actual
data structure layout.
Fixes: 1dd46599f8 ("spi: xilinx: add force_irq for QSPI mode")
Fixes: 082339bc63 ("spi: spi-xilinx: Add run run-time endian detection")
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240308162920.46816-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This was a relatively calm development cycle. Most of changes are
rather small device-specific fixes and enhancements. The only
significant changes in ALSA core are code refactoring with the recent
cleanup infrastructure, which should bring no functionality changes.
Some highlights below:
Core:
- Lots of cleanups in ALSA core code with automatic kfree cleanup
and locking guard macros
- New ALSA core kunit test
ASoC:
- SoundWire support for AMD ACP 6.3 systems
- Support for reporting version information for AVS firmware
- Support DSPless mode for Intel Soundwire systems
- Support for configuring CS35L56 amplifiers using EFI calibration
data
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
HD- and USB-audio:
- More Cirrus HD-audio codec support
- TAS2781 HD-audio codec fixes
- Scarlett2 mixer fixes
Others:
- Enhancement of virtio driver for audio control supports
- Cleanups of legacy PM code with new macros
- Firewire sound updates
-----BEGIN PGP SIGNATURE-----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=h9kz
-----END PGP SIGNATURE-----
Merge tag 'sound-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This was a relatively calm development cycle. Most of changes are
rather small device-specific fixes and enhancements. The only
significant changes in ALSA core are code refactoring with the recent
cleanup infrastructure, which should bring no functionality changes.
Some highlights below:
Core:
- Lots of cleanups in ALSA core code with automatic kfree cleanup and
locking guard macros
- New ALSA core kunit test
ASoC:
- SoundWire support for AMD ACP 6.3 systems
- Support for reporting version information for AVS firmware
- Support DSPless mode for Intel Soundwire systems
- Support for configuring CS35L56 amplifiers using EFI calibration
data
- Log which component is being operated on as part of power
management trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
HD- and USB-audio:
- More Cirrus HD-audio codec support
- TAS2781 HD-audio codec fixes
- Scarlett2 mixer fixes
Others:
- Enhancement of virtio driver for audio control supports
- Cleanups of legacy PM code with new macros
- Firewire sound updates"
* tag 'sound-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (307 commits)
ALSA: usb-audio: Stop parsing channels bits when all channels are found.
ALSA: hda/tas2781: remove unnecessary runtime_pm calls
ALSA: hda/realtek - ALC236 fix volume mute & mic mute LED on some HP models
ALSA: aaci: Delete unused variable in aaci_do_suspend
ALSA: scarlett2: Fix Scarlett 4th Gen input gain range again
ALSA: scarlett2: Fix Scarlett 4th Gen input gain range
ALSA: scarlett2: Fix Scarlett 4th Gen autogain status values
ALSA: scarlett2: Fix Scarlett 4th Gen 4i4 low-voltage detection
ALSA: hda/tas2781: restore power state after system_resume
ALSA: hda/tas2781: do not call pm_runtime_force_* in system_resume/suspend
ALSA: hda/tas2781: do not reset cur_* values in runtime_suspend
ALSA: hda/tas2781: add lock to system_suspend
ALSA: hda/tas2781: use dev_dbg in system_resume
ALSA: hda/realtek: fix ALC285 issues on HP Envy x360 laptops
platform/x86: serial-multi-instantiate: Add support for CS35L54 and CS35L57
ALSA: hda: cs35l56: Add support for CS35L54 and CS35L57
ASoC: cs35l56: Add support for CS35L54 and CS35L57
ASoC: Intel: catpt: Carefully use PCI bitwise constants
ALSA: hda: hda_component: Include sound/hda_codec.h
ALSA: hda: hda_component: Add missing #include guards
...
First of all, last_cs_index_mask should be aligned with the original
cs_index_mask, which is 16-bit (for now) wide. Use the same pattern
for the last_cs_index_mask.
Second, last_cs can be negative and since 'char' is equal to 'unsigned
char' in the kernel, it's incorrect, strictly speaking, to assign
signed number to it. Use s8 type as it's done for *_native_cs ones.
With this change, regroup a bit the ordering to avoid too much memory
space to be wasted due to paddings. Shuffle kernel documentation
accordignly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240307150256.3789138-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a new spi_optimize_message() function that can be used to
optimize SPI messages that are used more than once. Peripheral drivers
that use the same message multiple times can use this API to perform SPI
message validation and controller-specific optimizations once and then
reuse the message while avoiding the overhead of revalidating the
message on each spi_(a)sync() call.
Internally, the SPI core will also call this function for each message
if the peripheral driver did not explicitly call it. This is done to so
that controller drivers don't have to have multiple code paths for
optimized and non-optimized messages.
A hook is provided for controller drivers to perform controller-specific
optimizations.
Suggested-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/linux-spi/39DEC004-10A1-47EF-9D77-276188D2580C@martin.sperl.org/
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240219-mainline-spi-precook-message-v2-1-4a762c6701b9@baylibre.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. Recent work by Uwe
completes this renaming. However, there are plenty of leftovers in
the comments and in-code documentation. Update them as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240209165423.2305493-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
This series finishes off the removal of some of the legacy names for
SPI controllers and devices.
In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
the SPI bitbang controller drivers.
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/f7f949feb803acb8bea75798f41371a13287f4e8.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The __spi_split_transfer_maxsize() function has a gpf argument to allow
callers to specify the type of memory allocation that needs to be used.
However, this function only allocates struct spi_transfer and is not
intended to be used from atomic contexts so this type should always be
GFP_KERNEL, so we can just drop the argument.
Some callers of these functions also passed GFP_DMA, but since only
struct spi_transfer is allocated and not any tx/rx buffers, this is
not actually necessary and is removed in this commit.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240206200648.1782234-1-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The members of `struct spi_message` were reordered in commit
ae2ade4ba5 ("spi: Reorder fields in 'struct spi_message'")
but the documentation comments were not updated to match.
This commit updates the comments to match the new order.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240131170732.1665105-1-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As reported by Guenter the limit we've got on the number of chip selects is
set too low for some systems, raise the limit. We should really remove the
hard coded limit but this is needed as a fix so let's do the simple thing
and raise the limit for now.
Fixes: 4d8ff6b099 ("spi: Add multi-cs memories support in SPI core")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://msgid.link/r/20240124-spi-multi-cs-max-v2-1-df6fc5ab1abc@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the driver core can properly handle constant struct bus_type,
move the spi_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://msgid.link/r/2024010549-erasure-swoop-1cc6@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch series adds support to the SPI framework for using multiple
chip selects.
AMD-Xilinx GQSPI controller has two advanced mode that allows the
controller to consider two flashes as one single device.
One of these two mode is the parallel mode in which each byte of data is
stored in both devices, the even bits in the lower flash & the odd bits in
the upper flash. The byte split is automatically handled by the QSPI
controller.
The other mode is the stacked mode in which both the flashes share the
same SPI bus but each of the device contain half of the data. In this mode,
the controller does not follow CS requests but instead internally wires the
two CS levels with the value of the most significant address bit.
For supporting both these modes SPI core need to be updated for providing
multiple CS for a single SPI device.
For adding multi CS support the SPI device need to be aware of all the CS
values. So, the "chip_select" member in the spi_device structure is now an
array that holds all the CS values.
spi_device structure now has a "cs_index_mask" member. This acts as an
index to the chip_select array. If nth bit of spi->cs_index_mask is set
then the driver would assert spi->chip_select[n].
In parallel mode all the chip selects are asserted/de-asserted
simultaneously and each byte of data is stored in both devices, the even
bits in one, the odd bits in the other. The split is automatically handled
by the GQSPI controller. The GQSPI controller supports a maximum of two
flashes connected in parallel mode. A SPI_CONTROLLER_MULTI_CS flag bit is
added in the spi controller flags, through ctlr->flags the spi core
will make sure that the controller is capable of handling multiple chip
selects at once.
For supporting multiple CS via GPIO the cs_gpiod member of the spi_device
structure is now an array that holds the gpio descriptor for each
chipselect.
CS GPIO is not tested on our hardware, but it has been tested by @Stefan
https://lore.kernel.org/all/005001da1efc$619ad5a0$24d080e0$@opensource.cirrus.com/
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Tested-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231125092137.2948-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Nam Cao <namcao@linutronix.de>:
While running the spl022, I got the following warning:
BUG: sleeping function called from invalid context at drivers/spi/spi.c:1428
This is because between spi transfers, spi_transfer_delay_exec() (who
may sleep if the delay is >10us) is called in interrupt context. This is
a problem for anyone who runs this driver and need more than 10us delay.
Patch 1 adds an error reporting mechanism, needed by patch 2 who switch
to use the default spi_transfer_one_message(), which fix the problem.
The series is tested with polling transfer mode and interrupt transfer
mode. I can't test the DMA mode, so some help testing here is very
appreciated.
This commit updates the SPI subsystem, particularly affecting "SPI MEM"
drivers and core parts, by replacing the -ENOTSUPP error code with
-EOPNOTSUPP.
The key motivations for this change are as follows:
1. The spi-nor driver currently uses EOPNOTSUPP, whereas calls to spi-mem
might return ENOTSUPP. This update aims to unify the error reporting
within the SPI subsystem for clarity and consistency.
2. The use of ENOTSUPP has been flagged by checkpatch as inappropriate,
mainly being reserved for NFS-related errors. To align with kernel coding
standards and recommendations, this change is being made.
3. By using EOPNOTSUPP, we provide more specific context to the error,
indicating that a particular operation is not supported. This helps
differentiate from the more generic ENOTSUPP error, allowing drivers to
better handle and respond to different error scenarios.
Risks and Considerations:
While this change is primarily intended as a code cleanup and error code
unification, there is a minor risk of breaking user-space applications
that rely on specific return codes for unsupported operations. However,
this risk is considered low, as such use-cases are unlikely to be common
or critical. Nevertheless, developers and users should be aware of this
change, especially if they have scripts or tools that specifically handle
SPI error codes.
This commit does not introduce any functional changes to the SPI subsystem
or the affected drivers.
Signed-off-by: "Chia-Lin Kao (AceLan)" <acelan.kao@canonical.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20231129064311.272422-1-acelan.kao@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default message transfer implementation - spi_transfer_one_message -
invokes the specific device driver's transfer_one(), then waits for
completion. However, there is no mechanism for the device driver to
report failure in the middle of the transfer.
Introduce SPI_TRANS_FAIL_IO for drivers to report transfer failure.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/4b420dac528e60f122adde16851da88e4798c1ea.1701274975.git.namcao@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_MASTER_HALF_DUPLEX is the legacy name of a definition
for a half duplex flag. Since all others had been replaced with
the respective SPI_CONTROLLER prefix get rid of the last one
as well. There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20231113111249.3982461-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A race condition exists where a synchronous (noqueue) transfer can be
active during a system suspend. This can cause a null pointer
dereference exception to occur when the system resumes.
Example order of events leading to the exception:
1. spi_sync() calls __spi_transfer_message_noqueue() which sets
ctlr->cur_msg
2. Spi transfer begins via spi_transfer_one_message()
3. System is suspended interrupting the transfer context
4. System is resumed
6. spi_controller_resume() calls spi_start_queue() which resets cur_msg
to NULL
7. Spi transfer context resumes and spi_finalize_current_message() is
called which dereferences cur_msg (which is now NULL)
Wait for synchronous transfers to complete before suspending by
acquiring the bus mutex and setting/checking a suspend flag.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20231107144743.v1.1.I7987f05f61901f567f7661763646cb7d7919b528@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@kernel.org
Export acpi_spi_find_controller_by_adev() so that ACPI glue code which
wants to dynamically create a spi_device using acpi_spi_device_alloc() or
spi_new_device() on a controller, to which the code does not already have
a reference, can find the controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231014205314.59333-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct spi_message can be embedded into another structures.
With that the flexible array might be problematic as sparse
complains about it, although there is no real issue in the code
because when the message is embedded it doesn't use flexible array
member. That memeber is a private to spi_message_alloc() API, so
move it to that API in a form of an inherited data type.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes: 75e308ffc4 ("spi: Use struct_size() helper"))
Closes: https://lore.kernel.org/r/20231009-onshore-underage-c58415adfd92-mkl@pengutronix.de
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20231010163100.89734-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change legacy name master/slave to modern name host/target.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230818093154.1183529-20-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
This patch chain adds support for the Cirrus Logic cs42l43 PC focused
SoundWire CODEC.
* fsl_upm: Fix an off-by one test in fun_exec_op()
* Rockchip:
- Align hwecc vs. raw page helper layouts
- Fix oobfree offset and description
* Meson: Fix OOB available bytes for ECC
* Omap ELM: Fix incorrect type in assignment
SPI-NOR fixes:
* Avoid holes in struct spi_mem_op
Hyperbus fixes:
* Add Tudor as reviewer in MAINTAINERS
SPI-NAND fixes:
* Winbond and Toshiba: Fix ecc_get_status
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmTMpxoACgkQJWrqGEe9
VoR89gf/QDAw8A8Z58mxcEdrklRB+JD2w1FrnbsZ43bfhHYNvdA+5X+TmpmQmPnA
B+fGt2wc1yOIXzVE19ki+RGe+orxeo/Aw9t5ngQvFgdjXzqRdiKA43J3+t/QRew1
W2UKCEwiWnIkM1lYqzuN0tNr1eG+Cj/BkM695/VNCibTgdQL1SxA9V/Y3+9SR5cf
jvkWK3MESwN/FhfJ1m4nsI6kOtnG7bk65LSY/VpBQVIwtTEqC8aR27nShY4JuWL8
7EmE1J6hs+NUe9AbWgTwf68Z4ysgx44UwXfEfIROTwL4fNBRcKHG48GZbBHEe7v2
raRkxxLvlDDD48L7bP9e+bUSAKc2EQ==
=aP8/
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"Raw NAND fixes:
- fsl_upm: Fix an off-by one test in fun_exec_op()
- Rockchip:
- Align hwecc vs. raw page helper layouts
- Fix oobfree offset and description
- Meson: Fix OOB available bytes for ECC
- Omap ELM: Fix incorrect type in assignment
SPI-NOR fix:
- Avoid holes in struct spi_mem_op
Hyperbus fix:
- Add Tudor as reviewer in MAINTAINERS
SPI-NAND fixes:
- Winbond and Toshiba: Fix ecc_get_status"
* tag 'mtd/fixes-for-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: fsl_upm: Fix an off-by one test in fun_exec_op()
mtd: spi-nor: avoid holes in struct spi_mem_op
MAINTAINERS: Add myself as reviewer for HYPERBUS
mtd: rawnand: rockchip: Align hwecc vs. raw page helper layouts
mtd: rawnand: rockchip: fix oobfree offset and description
mtd: rawnand: meson: fix OOB available bytes for ECC
mtd: rawnand: omap_elm: Fix incorrect type in assignment
mtd: spinand: winbond: Fix ecc_get_status
mtd: spinand: toshiba: Fix ecc_get_status
gcc gets confused when -ftrivial-auto-var-init=pattern is used on sparse
bit fields such as 'struct spi_mem_op', which caused the previous false
positive warning about an uninitialized variable:
drivers/mtd/spi-nor/spansion.c: error: 'op' is used uninitialized [-Werror=uninitialized]
In fact, the variable is fully initialized and gcc does not see it being
used, so the warning is entirely bogus. The problem appears to be
a misoptimization in the initialization of single bit fields when the
rest of the bytes are not initialized.
A previous workaround added another initialization, which ended up
shutting up the warning in spansion.c, though it apparently still happens
in other files as reported by Peter Foley in the gcc bugzilla. The
workaround of adding a fake initialization seems particularly bad
because it would set values that can never be correct but prevent the
compiler from warning about actually missing initializations.
Revert the broken workaround and instead pad the structure to only
have bitfields that add up to full bytes, which should avoid this
behavior in all drivers.
I also filed a new bug against gcc with what I found, so this can
hopefully be addressed in future gcc releases. At the moment, only
gcc-12 and gcc-13 are affected.
Cc: Peter Foley <pefoley2@pefoley.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110743
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=108402
Link: https://godbolt.org/z/efMMsG1Kx
Fixes: 420c4495b5 ("mtd: spi-nor: spansion: make sure local struct does not contain garbage")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230719190045.4007391-1-arnd@kernel.org
The corgi_lcd_limit_intensity() function is called from platform
and defined in a driver, but the driver does not see the declaration:
drivers/video/backlight/corgi_lcd.c:434:6: error: no previous prototype for 'corgi_lcd_limit_intensity' [-Werror=missing-prototypes]
434 | void corgi_lcd_limit_intensity(int limit)
Move the prototype into a header that can be included from both
sides to shut up the warning.
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Documentation/process/deprecated.rst suggests to use flexible array
members to provide a way to declare having a dynamically sized set of
trailing elements in a structure.This makes code robust agains bunch of
the issues described in the documentation, main of which is about the
correctness of the sizeof() calculation for this data structure.
Due to above, prefer struct_size() over open-coded versions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714091748.89681-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename SPI_MASTER_GPIO_SS to SPI_CONTROLLER_GPIO_SS and
convert the users to SPI_CONTROLLER_GPIO_SS to follow
the new naming shema.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-14-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the users from SPI_MASTER_MUST_TX and/or SPI_MASTER_MUST_RX
to SPI_CONTROLLER_MUST_TX and/or SPI_CONTROLLER_MUST_RX respectively
and kill the not used anymore definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the users from SPI_MASTER_NO_TX and/or SPI_MASTER_NO_RX
to SPI_CONTROLLER_NO_TX and/or SPI_CONTROLLER_NO_RX respectively
and kill the not used anymore definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been converted in
the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block
-----BEGIN PGP SIGNATURE-----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=3KNJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, some improvements to the core code, lots of
different updates to existing GPIO drivers and some dt-bindings on
top.
There's nothing controversial in here and almost everything has been
in next for more than a week (95% a lot longer than this). The only
thing that has spent less time in next is a new driver so no risk of
regressions.
The single merge pulls in changes that remove all usage of global GPIO
numbers from arch/arm/mach-omap.
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers:
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down
delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been
converted in the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block"
* tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (58 commits)
of: unittest: drop assertions for GPIO hog messages
gpiolib: Drop unused domain_ops memeber of GPIO IRQ chip
gpio: synq: remove unused zynq_gpio_irq_reqres/zynq_gpio_irq_relres
dt-bindings: gpio: gpio-vf610: Add parsing of hogs
gpio: lpc18xx: Remove unused of_gpio.h inclusion
gpio: xra1403: Remove unused of_gpio.h inclusion
gpio: mpc8xxx: Remove unused of_gpio.h inclusion
dt-bindings: gpio: Add Cirrus EP93xx
gpio: mpc8xxx: latch GPIOs state on module load when configured as output
selftests: gpio: gpio-sim: Use same variable name for sysfs pathname
gpio: mlxbf3: Add gpio driver support
gpio: delay: Remove duplicative functionality
gpio: aggregator: Set up a parser of delay line parameters
gpio: aggregator: Support delay for setting up individual GPIOs
gpio: aggregator: Remove CONFIG_OF and of_match_ptr() protections
dt-bindings: gpio: pca9570: add gpio-line-names property
gpiolib: remove unused gpio_cansleep()
gpio: tps65219: add GPIO support for TPS65219 PMIC
gpio: zynq: fix zynqmp_gpio not an immutable chip warning
gpio: davinci: make davinci_gpio_dev_pm_ops static
...
Big transfers might take a bit of time, too constraining timeouts might
lead to false positives. In order to simplify the drivers work and with
the goal of factorizing code in mind, let's add a helper that can be
used by any spi controller driver to derive a relevant per-transfer
timeout value.
The logic is simple: we know how much time it would take to transfer a
byte, we can easily derive the total theoretical amount of time involved
for each transfer. We multiply it by two to have a bit of margin and
enforce a minimum of 500ms.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-2-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Nokia 770 is using GPIOs from the global numberspace on the
CBUS node to pass down to the LCD controller. This regresses when we
let the OMAP GPIO driver use dynamic GPIO base.
The Nokia 770 now has dynamic allocation of IRQ numbers, so this
needs to be fixed for it to work.
As this is the only user of LCD MIPID we can easily augment the
driver to use a GPIO descriptor instead and resolve the issue.
The platform data .shutdown() callback wasn't even used in the
code, but we encode a shutdown asserting RESET in the remove()
callback for completeness sake.
The CBUS also has the ADS7846 touchscreen attached.
Populate the devices on the Nokia 770 CBUS I2C using software
nodes instead of platform data quirks. This includes the LCD
and the ADS7846 touchscreen so the conversion just brings the LCD
along with it as software nodes is an all-or-nothing design
pattern.
The ADS7846 has some limited support for using GPIO descriptors,
let's convert it over completely to using device properties and then
fix all remaining boardfile users to provide all platform data using
software nodes.
Dump the of includes and of_match_ptr() in the ADS7846 driver as part
of the job.
Since we have to move ADS7846 over to obtaining the GPIOs it is
using exclusively from descriptors, we provide descriptor tables
for the two remaining in-kernel boardfiles using ADS7846:
- PXA Spitz
- MIPS Alchemy DB1000 development board
It was too hard for me to include software node conversion of
these two remaining users at this time: the spitz is using a
hscync callback in the platform data that would require further
GPIO descriptor conversion of the Spitz, and moving the hsync
callback down into the driver: it will just become too big of
a job, but it can be done separately.
The MIPS Alchemy DB1000 is simply something I cannot test, so take
the easier approach of just providing some GPIO descriptors in
this case as I don't want the patch to grow too intrusive.
As we see that several device trees have incorrect polarity flags
and just expect to bypass the gpiolib polarity handling, fix up
all device trees too, in a separate patch.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TPM specification [1] defines flow control over SPI. Client device can
insert a wait state on MISO when address is transmitted by controller
on MOSI. Detecting the wait state in software is only possible for
full duplex controllers. For controllers that support only half-
duplex, the wait state detection needs to be implemented in hardware.
Add a flag SPI_TPM_HW_FLOW for TPM device to set when software flow
control is not possible and hardware flow control is expected from
SPI controller.
Reference:
[1] https://trustedcomputinggroup.org/resource/pc-client-platform-tpm
-profile-ptp-specification/
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230421091309.2672-2-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
