Add support for reading the SERDES statistics of the mv88e8352, using
the standard ethtool -S option. The SERDES interface can be mapped to
either port 4 or 5, so only return statistics on those ports, if the
SERDES interface is in use.
The counters are reset on read, so need to be accumulated. Add a per
port structure to hold the stats counters. The 6352 only has a single
SERDES interface and so only one port will using the newly added
array. However the 6390 family has as many SERDES interfaces as ports,
each with statistics counters. Also, PTP has a number of counters per
port which will also need accumulating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the existing code. This helper will be used for SERDES
statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gettting the number of statistics, the strings and the actual
statistics, call the SERDES ops if implemented. This means the stats
code needs to return the number of strings/stats they have placed into
the data, so that the SERDES strings/stats can follow on.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, there has been no need to hold the reg mutex while getting
the count of statistics, or the strings, because the hardware was not
accessed. When adding support for SERDES statistics, it is necessary
to access the hardware, to determine if a port is using the SERDES
interface. So add mutex lock/unlocks.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to 28678f07f1 ("mlxsw: spectrum_router: Update multipath hash
parameters upon netevents") for IPv4, make sure the kernel and asic are
using the same hash algorithm for path selection.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does path selection for multipath routes deep in the lookup
functions. The next patch adds L4 hash option and needs the skb
for the forward path. To get the skb to the relevant FIB lookup
functions it needs to go through the fib rules layer, so add a
lookup_data argument to the fib_lookup_arg struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename NETEVENT_MULTIPATH_HASH_UPDATE to
NETEVENT_IPV4_MPATH_HASH_UPDATE to denote it relates to a change
in the IPv4 hash policy.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro on a couple of arrays to determine
size of the arrays. Also fix up alignment to clean up a checkpatch
warning. Improvement suggested by Coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim net namespace stuff from Kirill Tkhai
* A-MSDU support in fast-RX
* 4-addr mode support in fast-RX
* support for a spec quirk in Add-BA negotiation
-----BEGIN PGP SIGNATURE-----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=BTxG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Only a few new things:
* hwsim net namespace stuff from Kirill Tkhai
* A-MSDU support in fast-RX
* 4-addr mode support in fast-RX
* support for a spec quirk in Add-BA negotiation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code is already returned earlier if filter exists
at specified location. So, remove dead code trying to
free existing filter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations allocate and destroy IDA identifier,
and these actions are synchronized by IDA subsystem locks.
Exit method removes mac80211_hwsim_data enteries from the lists,
and this is synchronized by hwsim_radio_lock with the rest
parallel pernet_operations. Also it queues destroy_radio()
work, and these work already may be executed in parallel
with any pernet_operations (as it's a work :). So, we may
mark these pernet_operations as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim_netgroup counter is declarated as int, and it is incremented
every time a new net is created. After sizeof(int) net are created,
it will overflow, and different net namespaces will have the same
identifier. This patch fixes the problem by introducing IDA instead
of int counter. IDA guarantees, all the net namespaces have the uniq
identifier.
Note, that after we do ida_simple_remove() in hwsim_exit_net(),
and we destroy the ID, later there may be executed destroy_radio()
from the workqueue. But destroy_radio() does not use the ID, so it's OK.
Out of bounds of this patch, just as a report to wireless subsystem
maintainer, destroy_radio() increaments hwsim_radios_generation
without hwsim_radio_lock, so this may need one more patch to fix.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cortina_soft_reset() does the same thing as gen10g_soft_reset(), and
cortina_config_aneg() is actually doing what gen10g_config_init() does
for 10G capable PHYs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update teranetics_aneg_done() to use genphy_c45_aneg_done() instead of
duplicating that code, and switch to gen10g_* functions where
appropriate instead of maintaining identical copies doing nothing.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to remove a fair amount of duplication in the different 10G PHY
drivers, export all gen10g_* functions to be able to make use of those.
While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset()
to illustrate what it does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adopt the conventional style of debug logging because it is both
shorter and more flexible.
Remove the 'version_printed' flag as the version will be printed
only once anyway (when the module loads).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix log message fragments that no longer produce the desired output
since the behaviour of printk() was changed.
Add missing printk severity levels.
Drop deprecated "out of memory" message as per checkpatch advice.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently these Dayna cards don't have a pseudoslot declaration ROM
which means they can't be probed like NuBus cards.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of working on MII time stamping infrastructure, I was trying
to figure out how netdev->phydev gets assigned, and I stumbled across
this. Ever since the new phylink code came in, the field is assigned
twice.
The function, phylink_connect_phy(), calls
phy_attach_direct()
phylink_bringup_phy()
and phy_attach_direct() sets
dev->phydev = phydev;
but phylink_bringup_phy() then sets the same field again:
pl->netdev->phydev = phy;
Similarly, the function, phylink_of_phy_connect(), calls
of_phy_attach()
phy_attach_direct()
phylink_bringup_phy()
The removal code is also duplicated:
phylink_disconnect_phy()
pl->netdev->phydev = NULL;
phy_disconnect()
phy_detach()
phydev->attached_dev->phydev = NULL;
This patch removes the redundant assignments, restricting manipulation
of the netdev.phydev field to phy_attach_direct() and phy_detach().
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mfc_cache and mfc6_cache are almost identical - the main difference is
in the origin/group addresses and comparison-key. Make a common
structure encapsulating most of the multicast routing logic - mr_mfc
and convert both ipmr and ip6mr into using it.
For easy conversion [casting, in this case] mr_mfc has to be the first
field inside every multicast routing abstraction utilizing it.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of MSI-X the interrupt number may differ from pcidev->irq.
Fix this by using pci_irq_vector().
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-02-28
This series contains updates to fm10k only.
Jake provides all the changes in this series, starting with making the
function header comments consistent and to align with how the kernel
documentation expects it. Also cleaned up code comment as well as bump
the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This changeset moves ipvlan address under RCU protection, using
a per ipvlan device spinlock to protect list mutation and RCU
read access to protect list traversal.
Also explicitly use RCU read lock to traverse the per port
ipvlans list, so that we can now perform a full address lookup
without asserting the RTNL lock.
Overall this allows the ipvlan driver to check fully for duplicate
addresses - before this commit ipv6 addresses assigned by autoconf
via prefix delegation where accepted without any check - and avoid
the following rntl assertion failure still in the same code path:
RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124)
WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan]
Modules linked in: ipvlan(E) ixgbe
CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782
Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016
RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan]
RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300
RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00
R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0
Call Trace:
<IRQ>
ipvlan_addr6_event+0x6c/0xd0 [ipvlan]
notifier_call_chain+0x49/0x90
atomic_notifier_call_chain+0x6a/0x100
ipv6_add_addr+0x5f9/0x720
addrconf_prefix_rcv_add_addr+0x244/0x3c0
addrconf_prefix_rcv+0x2f3/0x790
ndisc_router_discovery+0x633/0xb70
ndisc_rcv+0x155/0x180
icmpv6_rcv+0x4ac/0x5f0
ip6_input_finish+0x138/0x6a0
ip6_input+0x41/0x1f0
ipv6_rcv+0x4db/0x8d0
__netif_receive_skb_core+0x3d5/0xe40
netif_receive_skb_internal+0x89/0x370
napi_gro_receive+0x14f/0x1e0
ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe]
ixgbe_poll+0x31a/0x7a0 [ixgbe]
net_rx_action+0x296/0x4f0
__do_softirq+0xcf/0x4f5
irq_exit+0xf5/0x110
do_IRQ+0x62/0x110
common_interrupt+0x91/0x91
</IRQ>
v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event()
Fixes: e9997c2938 ("ipvlan: fix check for IP addresses in control path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if IPv6 is enabled on top of an ipvlan device in l3
mode, the following warning message:
Dropped {multi|broad}cast of type= [86dd]
is emitted every time that a RS is generated and dmseg is soon
filled with irrelevant messages. Replace pr_warn with pr_debug,
to preserve debuggability, without scaring the sysadmin.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle graft command for an offloaded sch_prio.
Grafting a qdisc to any place other than under its original parent is not
supported by mlxsw and will cause the grafted qdisc to stop being
offloaded.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number the bands of sch_prio is decreased, child qdiscs on the
deleted bands would get deleted as well.
This change and deletions are being done under sch_tree_lock of the
sch_prio qdisc. Part of the destruction of qdisc is unoffloading it, if
it is offloaded. Un-offloading can't be done inside this lock.
Move the offload command to be done before reducing the number of bands,
so unoffloading of the qdiscs that are about to be deleted could be done
outside of the lock.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_prio as root qdisc should count all the drops its children have. Since
it is possible for it to have sch_red children, it needs to count RED early
drops.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a child qdisc its backlog will be decreased from the parent
backlog. The driver backlog count should do the same.
When the parent changes its configuration, the child might need to clean
its stats. However, the backlog can't be cleaned with the rest of the
stats, because it reflects a momentary value that needs to be synced with
the core, not the history of the qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Priority counters count packets according to their packet priority.
Collect the stats for sch_red based on these counters, so the qdisc bstats
will be the sum of counters matching the priorities marked in the qdisc
priomap.
Changing the mapping of the priorities to bands while traffic is running
can result in losing the stats of the bands qdiscs from their last dump
call to this change, as if the qdisc was unoffloaded and re-offloaded. It
will not affect the traffic behaviour according to sch_red.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add priority map per qdisc, to indicate which priorities are being
directed through this qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TX packets and bytes counters per switch priority per port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the option to set a qdisc per tclass. Match the qdisc to the tclass by
parent ID. Supported currently for sch_red only.
It allows offloading sch_prio as root qdisc and sch_red as its child.
(However, doing so might corrupt the stats for both parent and child.)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller allows for generic packet filtering. This commit
adds entries to implement VLAN filtering. The approach taken is :
- Filter entries that would match on the presence of the VLAN tag
(existing VLAN detection, DSA / EDSA detection) will set the next
lookup ID to be for the VID.
- For each VLAN existing on a given port, we add an entry that matches
this specific VID. If the incoming packet matches the VID entry, it is
set for the next lookup in the chain (LU_L2).
- A Guard entry is added for each port, that will match if the incoming
packet didn't match any of the above VID entries. This entry tags the
packet to be dropped.
Due to this design, and the fact that the total 256 filter entries are
also used for other purposes, we have a limit of 10 VLANs per port. To
accommodate the case where we would need more VLANS on one port, this
patch implements the ndo_set_features to allow for disabling of VLAN
filtering using ethtool.
The default config has VLAN filtering disabled.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that only one feature flag is left we can convert it and remove
enum features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MACH_IS_MAC test is redundant here because the platform device
won't get registered unless MACH_IS_MAC.
Adopt module_platform_driver() convention.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't log the unexpanded "eth%d" format string.
Log the chip revision in the probe message (consistent with mace.c).
Drop redundant debug messages for FIFO events recorded in the
interface statistics (also consistent with mace.c).
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: This is compile only tested as I have no access to the hw.
No benefit gained except for some self-documenting.
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
Function old new delta
Total: Before=2757703, After=2757703, chg +0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: This is compile only tested as I have no access to the hw.
Constifying and declaring as static saves 24 bytes.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-24 (-24)
Function old new delta
pkt_type_str 24 - -24
Total: Before=3599256, After=3599232, chg -0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of work by both Jon Nettleton and Russell King.
Jon wrote the original patch, adding support for SFP modules which
require a power level greater than '1'.
Russell's changes:
- Fix the power levels for big-endian, and make the code flow better.
- Convert to use device_property_read_u8()
- Warn for power levels exceeding host level
SFF-8431 says:
"To avoid exceeding system power supply limits and cooling capacity,
all modules at power up by default shall operate with up to 1.0 W.
Hosts supporting Power Level II or III operation may enable a Power
Level II or III module through the 2-wire interface. Power Level II
or III modules shall assert the power level declaration bit of
SFF-8472."
Print a warning for modules that exceed the host power level, and
leave them operating in power level 1.
- Fix i2c write
The first byte of any write after the bus address is always the
device address. In order to write a value to device D, address I,
value V, we need to generate on the bus:
S DDDDDDDD A IIIIIIII A VVVVVVVV A P
where S = start, R = restart, A = ack, P = stop. Splitting this
as two:
S DDDDDDDD A IIIIIIII A R DDDDDDDD A VVVVVVVV A P
results in the device's address register being written first by I
and then by V - the addressed register within the device is not
written.
- Avoid power mode switching if 0xa2 is not implemented
Some modules indicate that they support power level II or power level
III, but do not implement address 0xa2, meaning that the bit to set
them to high power mode is not accessible.
These modules appear to have the sff8472_compliance field set to zero,
and also do not implement diagnostics. Detect this, but also ensure
that the module does not require the address switching mode, which we
do not implement.
- Use mW for power level rather than power level number.
- Fix high power mode transition
We must not switch to SFP_MOD_PRESENT state until we have finished
initialising, because the remaining state machines check for that
state. Add SFP_MOD_HPOWER as an intermediate state.
- Use definition for I2C register address rather than constant.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Negotiate the interface format with the MAC rather than requiring it to
be a fixed type specified solely by the SFP module. This allows modules
that can work with several different interface signalling formats to
select a format compatible with the MAC - for example, a Fiber module
supporing Gigabit ethernet and faster connected to a Gigabit only MAC
needs to select the 1000BASE-X mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some BiDi modules (eg, FiberStore SFP-GE-BX) are not compliant with
1000BASE-BX as they use different wavelengths from the 1000BASE-BX
standard (eg, 1310nm/1550nm rather than 1310nm/1490nm). These modules
support 1000BASE-X ethernet, so detect them by a failure to find any
other support, the 8B10B encoding and a bit rate that falls within the
1Gbps window.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use extack inside team's enslavement function and also propagate it to
the netdevice notifier to allow enslaved ports to report the failure
reason. Example:
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev lo master team0
Error: Loopback device can't be added as a team port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're aligned with latest version released on SourceForge, so update the
version number to match.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent kernels now complain about incorrect function prototype comments,
in order to ensure comments are accurate to the function. However, it
incorrectly associates the comment above the fm10k_pci_tbl[] as
a function header comment. Fix this by removing the extra "*" in the
comment. This normally indicates that the function is a doxygen style
function header comment.
Once removed, the logic no longer kicks in and the following warning is
fixed:
warning: cannot understand function prototype: 'const struct pci_device_id fm10k_pci_tbl[] = '
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several function header comments had incorrect function parameter
definitions. Recent versions of the upstream kernel have started to warn
about these issues. Fix up the comments which do not match in order to
resolve these new warnings.
While fixing these, update the copyright year also.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
