Add new peripherals to the MPFS, and enable them in the Icicle kit
device tree:
2x SPI, QSPI, 3x GPIO, 2x I2C, Real Time Counter, PCIE controller,
USB host & system controller.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Assorted minor changes to the MPFS/Icicle kit device tree:
- enable mmuart4 instead of mmuart0
- remove sifive pdma
- split memory node to match updated fpga design
- move stdout path to serial1 to avoid collision with
bootloader running on the e51
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Split the device tree for the Microchip MPFS into two sections by adding
microchip-mpfs-fabric.dtsi, which contains peripherals contained in the
FPGA fabric.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Update the Microchip Icicle kit device tree by replacing clock
related magic numbers with their defined counterparts.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
"make dtbs_check" reports:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: soc: refclk: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[600000000]], 'clock-output-names': ['msspllclk'], 'phandle': [[7]]} should not be valid under {'type': 'object'}
From schema: dtschema/schemas/simple-bus.yaml
Fix this by moving the node out of the "soc" subnode.
While at it, rename it to "msspllclk", and drop the now superfluous
"clock-output-names" property.
Move the actual clock-frequency value to the board DTS, since it is not
set until bitstream programming time.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Devicetree source is a description of hardware and hardware has only one
block @20008000 which can be configured either as eMMC or SDHC. Having
two node for different modes is an obscure, unusual and confusing way to
configure it. Instead the board file is supposed to customize the block
to its needs, e.g. to SDHC mode.
This fixes dtbs_check warning:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: sdhc@20008000: $nodename:0: 'sdhc@20008000' does not match '^mmc(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
According to bindings, the compatible must include microchip,mpfs. This
fixes dtbs_check warning:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: /: compatible: ['microchip,mpfs-icicle-kit'] is too short
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The DTSI file defines soc node and address/size cells, so there is no
point in duplicating it in DTS file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, nothing is output on the serial console, unless
"console=ttyS0,115200n8" or "earlycon" are appended to the kernel
command line. Enable automatic console selection using
chosen/stdout-path by adding a proper alias, and configure the expected
serial rate.
While at it, add aliases for the other three serial ports, which are
provided on the same micro-USB connector as the first one.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
U-Boot expects this alias to be in place in order to fix up the mac
address of the ethernet node.
Note on the Icicle Kit board, currently only emac1 is enabled so it
becomes the 'ethernet0'.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
