Add support for i2c5, which is used to access the
external I2C bus on connector J22 of the imx8mp-evk.
Limit the speed to 100kHz since this is an external I2C bus.
Disabled by default, since it is shared with the CAN1 bus.
To enable i2c5, you need to disable the CAN1 function, enable the i2c5
function and also configure the CAN1/I2C5_SEL GPIO to HIGH to
select i2c5 instead of CAN1. This can be done by defining a gpio-hog
inside the pca6416 node, in your board device tree, like in this example:
&flexcan1 {
status = "disabled";
};
&i2c5 {
status = "okay";
};
&pca6416 {
can1-i2c5-sel-hog {
gpio-hog;
gpios = <2 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "can1-i2c5-sel";
};
};
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add gpio-line-names for the various GPIO's connected to the PCA6416
I/O expander on the imx8mp EVK.
This helps when using the new gpiod interface to find the GPIOs by name.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add interrupt controller mode for the pca6416 on i.MX8MP EVK board's.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Eqos ethernet support five queues on hardware, enable these queues and
configure the priority of each queue. Uses Strict Priority as scheduling
algorithms to ensure that the TSN function works.
The priority of each queue is a bitmask value that maps VLAN tag
priority to the queue. Since the hardware only supports five queues,
this patch maps priority 0-4 to queues one by one, and priority 5-7 to
queue 4.
The total fifo size of 5 queues is 8192 bytes, if enable 5 queues with
store-and-forward mode, it's not enough for large packets, which would
trigger fifo overflow frequently. This patch set DMA to thresh mode to
enable all 5 queues.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to commit 0a4355c2b7 ("net: phy: realtek: add dt property to
disable CLKOUT clock"), diable CLKOUT clock for FEC PHY to save power on
i.MX8MP EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mp-evk uses an PCA9450C as PMIC that supplies various
regulators.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet RTL8211, it must be asserted low for at least
10ms and at least 72ms "for internal circuits settling time" before
accessing the PHY registers.
Add properties to describe such requirements.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable usb host port with type-A connector on imx8mp-evk board.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1609241866-9508-5-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different revision of i.MX8MP EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MP boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:
... 'usdhc3grp-100mhz', 'usdhc3grp-200mhz' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "pinctrl-names" property in iomux node does not make sense on its
own (without "pinctrl-X").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MP EVK board has a GPIO LED to indicate status, add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
