If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In OS descriptors handling, if ctrl->bRequestType is
USB_RECIP_DEVICE and w_index != 0x4 or (w_value >> 8)
is true, it will not assign a valid value to req->length,
but use the default value(-EOPNOTSUPP), and queue an
OS desc request with the invalid req->length. It always
happens on the platforms which use os_desc (for example:
rk3366, rk3399), and cause kernel panic as follows
(use dwc3 driver):
Unable to handle kernel paging request at virtual address ffffffc0f7e00000
Internal error: Oops: 96000146 [#1] PREEMPT SMP
PC is at __dma_clean_range+0x18/0x30
LR is at __swiotlb_map_page+0x50/0x64
Call trace:
[<ffffffc0000930f8>] __dma_clean_range+0x18/0x30
[<ffffffc00062214c>] usb_gadget_map_request+0x134/0x1b0
[<ffffffc0005c289c>] __dwc3_ep0_do_control_data+0x110/0x14c
[<ffffffc0005c2d38>] __dwc3_gadget_ep0_queue+0x198/0x1b8
[<ffffffc0005c2e18>] dwc3_gadget_ep0_queue+0xc0/0xe8
[<ffffffc00061cfec>] composite_ep0_queue.constprop.14+0x34/0x98
[<ffffffc00061dfb0>] composite_setup+0xf60/0x100c
[<ffffffc0006204dc>] android_setup+0xd8/0x138
[<ffffffc0005c29a4>] dwc3_ep0_delegate_req+0x34/0x50
[<ffffffc0005c3534>] dwc3_ep0_interrupt+0x5dc/0xb58
[<ffffffc0005c0c3c>] dwc3_thread_interrupt+0x15c/0xa24
With this patch, the gadget driver will not queue
a request and return immediately if req->length is
invalid. And the usb controller driver can handle
the unsupport request correctly.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If c->cdev->use_os_string flag is not set,
don't need to invoke ffs_do_os_descs() in _ffs_func_bind.
So uninitialized ext_compat_id pointer won't be accessed by
__ffs_func_bind_do_os_desc to cause kernel panic.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit dc8c46a5ae ("usb: gadget: f_tcm: convert to new function
interface with backward compatibility") introduced a possible out
of bounds memory access:
If tpg is not found in function usbg_drop_tpg,
tpg_instances[TPG_INSTANCES] is accessed.
Fixes: dc8c46a5ae ("usb: gadget: f_tcm: convert to new function interface with backward compatibility")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Function in_rq_cur copies random bytes from the stack.
Zero the memory instead.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq
MIPS system unfortunately broke big-endian operation on PowerPC
APM82181 as reported by Christian Lamparter, and likely other
systems.
It actually introduced multiple issues:
- it broke big-endian ARM kernels: any machine that was working
correctly with a little-endian kernel is no longer using byteswaps
on big-endian kernels, which clearly breaks them.
- On PowerPC the same thing must be true: if it was working before,
using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC
usually uses big-endian kernels, so they are likely all broken.
- The barrier for dwc2_writel is on the wrong side of the __raw_writel(),
so the MMIO no longer synchronizes with DMA operations.
- On architectures that require specific CPU instructions for MMIO
access, using the __raw_ variant may turn this into a pointer
dereference that does not have the same effect as the readl/writel.
This patch is a simple revert for all architectures other than MIPS,
in the hope that we can more easily backport it to fix the regression
on PowerPC and ARM systems without breaking the Lantiq system again.
We should follow this up with a more elaborate change to add runtime
detection of endianness, to make sure it also works on all other
combinations of architectures and implementations of the usb-dwc2
device. That patch however will be fairly large and not appropriate
for backports to stable kernels.
Felipe suggested a different approach, using an endianness switching
register to always put the device into LE mode, but unfortunately
the dwc2 hardware does not provide a generic way to do that. Also,
I see no practical way of addressing the problem more generally by
patching architecture specific code on MIPS.
Fixes: 95c8bc3609 ("usb: dwc2: Use platform endianness when accessing registers")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current __ffs_data_do_os_desc() of f_fs.c will check reserved1 field
of OS_DESC_EXT_COMPAT and return -EINVAL if it's 1.
But MS OS 1.0 Descriptors
http://msdn.microsoft.com/en-us/library/windows/hardware/gg463179.aspx
defines that field to be 1.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Device qualifier descriptor is now generated by composite.c
code. So let's fix this old comment by removing parts which
are no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code, so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a check in dwc2_hsotg_ep_sethalt() so that it does not halt
isochronous endpoints.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget API function usb_ep_set_halt() expects the gadget to return
-EAGAIN if the ep is active. Add support for this behavior.
Otherwise this may break mass storage protocol if a STALL is attempted
on the endpoint.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This loop is supposed to set all the .num[] values to -1 but it's off by
one so it skips the first element and sets one element past the end of
the array.
I've cleaned up the loop a little as well.
Fixes: ddf8abd259 ('USB: f_fs: the FunctionFS driver')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default user could store only valid UDC name in configfs UDC
attr by doing:
echo $UDC_NAME > UDC
Commit (855ed04 "usb: gadget: udc-core: independent registration of
gadgets and gadget drivers") broke this behavior and allowed to store
any arbitrary string in UDC file and udc core was waiting for such
controller to appear.
echo "any arbitrary string here" > UDC
This commit fix this by adding a flag which prevents configfs
gadget from being added to list of pending drivers if UDC with
given name has not been found.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
This patch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas) there's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXO8W0AAoJEDeqqVYsXL0MW24H/jGWwfjsDUiSsLwbLca6DWu8
ZCWZ7rSZ27CApwGPgZGpLvUg+vpW8Ykm2zdeBnlZ6ScXS+dT3uo/PHsnemsTextj
6glQNIOFY0Ja2GwkkN00M6IZQhTJ628cqJKIEJxC68lIw16wiOwjZaK68GMrusDO
Sl062rkuLR6Jb2T+YoT/sD8jQfWlSj2V9e9rqJoS/rIbS6B+hUipuybz2yQ2yK2u
XFc30yal9oVz1fHEoh2O8aqckW3/iskukVXVuZ0MQzT/lV/bm9I6AnWVHw7d0Yhp
ZELjXpjx5M2Z/d8k0Wvx1e25oL/ERwa96yLnTvRcqyF5Yt1EgAhT+jKvo4pnGr8=
=L6y/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
These updates fixes a number of issues where resources were not properly
released on probe errors. Included is also a fix for hardware
flow-control disable for cp210x.
Support for Moxa UPort 11x0 is added to the ti_usb_3410_5052 driver, and
included are also some general code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8igx
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.7-rc1
These updates fixes a number of issues where resources were not properly
released on probe errors. Included is also a fix for hardware
flow-control disable for cp210x.
Support for Moxa UPort 11x0 is added to the ti_usb_3410_5052 driver, and
included are also some general code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
The ohci-platform driver can control the clock, while usb-nop-xceiv
as the PHY can control the vbus regulator. So this JZ4740-specific
glue is not needed anymore.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13105/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
These devices are based on TI 3410 chip.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: fix rs485-only check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Due to a missing upper bound, invalid minor numbers could be assigned to
ports. Such devices would later fail to register, but let's catch this
early as intended and avoid having devices with only a subset of their
ports registered (potentially the empty set).
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # v3.5: 40d0473849
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f20 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The URB status is signed and should be printed using %d rather than %x.
Also print endpoint addresses consistently using %x rather than %d, and
merge a broken-up error message string.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A driver must not rely on the URB status field to try to determine if an
URB is active.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # v2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BcOx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "usb: host: xhci-tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
* tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
Remove unnecessary space before open square bracket.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right part of the following or expression is only evaluated if
td is nonzero.
!td || (td && td.status == USB_TD_INPROGRESS)
So no need to check td again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware of R-Car USB 3.0 host controller will control the reset.
So, if the xhci driver doesn't do firmware downloading (e.g. kernel
configuration is CONFIG_USB_XHCI_PLATFORM=y and CONFIG_USB_XHCI_RCAR
is not set), the reset of USB 3.0 host controller doesn't work
correctly. Then, the host controller will cause long wait in
xhci_reset() because the CMD_RESET bit of op_regs->command is not
cleared for 10 seconds.
So, this patch modifies the Kconfig to enable both CONFIG_USB_XHCI_PLATFORM
and CONFIG_USB_XHCI_RCAR.
Fixes: 4ac8918f3a (usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers)
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goto in create_sysfs_files is never executed, so remove it
and clean up the code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not initialise statics to 0.
This patch is found by checkpatch.pl script.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove space before ',' and '(' .
This patch is detected by checkpatch.pl
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S5N0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v4.6-rc7
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
The CRTSCTS flag code cleared (and inconsistently) bits unrelated to
CRTSCTS functionality. It was also harder than necessary to read.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replaced magic numbers used in the CRTSCTS flag code with symbolic names
from the chip specification.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
A bug in the CRTSCTS handling caused RTS to alternate between
CRTSCTS=0 => "RTS is transmit active signal" and
CRTSCTS=1 => "RTS is used for receive flow control"
instead of
CRTSCTS=0 => "RTS is statically active" and
CRTSCTS=1 => "RTS is used for receive flow control"
This only happened after first having enabled CRTSCTS.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
[johan: reword commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Some for documentation, some for tiny changes, thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKY35AAoJEEhZKYFQ1nG7S+4H/0e4uLWow82UxNrYCDUMo/VI
Cto62Qo/lQTQb3iTsU3WD/SA1GOB0fei2GL53YuqoqsOcHSQQHMvnWQLps/YCHtT
l/YMY0arxysFNHkA+8wGTrfnRi/Nm2dJlSlkAJleTgD09dnobHYTk4AVDjSqvvb5
gvpMReTe4+ZsC7Nitum7Sg3dLHCJBdmXAWLKBOZ9beDSw5t1xbImjt8ud8k/eAYG
UseCqp8BClhKYGmLOAPRZvootmIvKEahGt0z2YXSJoVuHs0e3+7K23EVSV+zR+0Y
WMHdQXR4HOl6bcuXiHUKpN9SvUff7IxcMLnP/cBJ2lLHSVNS0yzO+NBsogx/f28=
=0707
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Hi Greg, below are changes for chipidea and OTG FSM, no major changes.
Some for documentation, some for tiny changes, thanks.
Add even more ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
[johan: rebase and replace commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
More ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
[properly sort them - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The stack object “ci” has a total size of 8 bytes. Its last 3 bytes
are padding bytes which are not initialized and leaked to userland
via “copy_to_user”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the original DWC3_DCFG_NUMP() was always zero. It looks like the
intent was to shift first and then do the mask.
Fixes: 2a58f9c12b ('usb: dwc3: gadget: disable automatic calculation of ACK TP NUMP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b52490193 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Cc: <stable@vger.kernel.org> # v2.6.18+
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of usbhsp_setup_pipecfg() was u16 but it was returning
a negative value (-EINVAL). Lets have an additional argument which will
have pipecfg and just return the status (success or error) as the return
from the function.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Gemalto's Cinterion PH8 and AHxx products
with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface.
In addition some minor renaming and formatting.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
[johan: sort current entries and trim trailing whitespace ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit e3345db850, which
broke system resume for a large class of devices.
Devices that after having been reset during resume need to be rebound
due to a missing reset_resume callback, are now left in a suspended
state. This specifically broke resume of common USB-serial devices,
which are now unusable after system suspend (until disconnected and
reconnected) when USB persist is enabled.
During resume, usb_resume_interface will set the needs_binding flag for
such interfaces, but unlike system resume, run-time resume does not
honour it.
Cc: stable <stable@vger.kernel.org> # 4.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means all ->con_set_palette have to have the second parameter
const too now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging facilities in ehci-dbg.c follow an uneven pattern. Some
of them are protected by "#ifdef CONFIG_DYNAMIC_DEBUG" and some
aren't, presumably in the hope of having some of the debugging output
available in any configuration.
This leads to build problems when dynamic debugging isn't configured.
Rather than try to keep this complicated state of affairs, let's just
make everything dependent on CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One line above we have checked that udc is NULL so we shouldn't
dereference it while printing error message.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We read a struct usb_device_descriptor from it, so make it an actual
binary attribute.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@gmail.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Tested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Type-C Connector System Software Interface (UCSI) is
specification that defines the registers and data structures
that can be used to control USB Type-C ports on a system.
UCSI is used on several Intel Broxton SoC based platforms.
Things that UCSI can be used to control include at least USB
Data Role swapping, Power Role swapping and controlling of
Alternate Modes on top of providing general details about
the port and the partners that are attached to it.
The initial purpose of the UCSI driver is to make sure USB
is in host mode on desktop and server systems that are USB
dual role capable, and provide UCSI interface.
The goal is to integrate the driver later to an USB Type-C
framework for Linux kernel, and at the same time add support
for more extensive USB Type-C port control that UCSI offers,
for example data role swapping, power role swapping,
Alternate Mode control etc.
The UCSI specification is public can be obtained from here:
http://www.intel.com/content/www/us/en/io/universal-serial-bus/usb-type-c-ucsi-spec.html
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gyoi
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc6
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Parameterize more parts of the driver and add support for Tegra210.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the on-chip XUSB controller present on Tegra SoCs. This
controller, when loaded with external firmware, exposes an interface
compliant with xHCI. This driver loads the firmware, starts the
controller, and is able to service host-specific messages sent by the
controller's firmware.
The controller also supports USB device mode as well as powergating
of the SuperSpeed and host-controller logic when not in use, but
support for these is not yet implemented.
Based on work by:
Ajay Gupta <ajayg@nvidia.com>
Bharath Yadav <byadav@nvidia.com>
Andrew Bresticker <abrestic@chromium.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the root hub device is added to the bus, it tries to get pins
information from pinctrl (see pinctrl_bind_pins, at really_probe), if
the pin information is described at DT, it will show below error since
the root hub's device node is the same with controller's, but controller's
pin has already been requested when it is added to platform bus.
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by 2184000.usb; cannot claim for usb1
imx6q-pinctrl 20e0000.iomuxc: pin-137 (usb1) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp-3 on device 20e0000.iomuxc
usb usb1: Error applying setting, reverse things back
To fix this issue, we move the root hub's device node assignment (equals
to contrller's) after device is added to bus, we only need to know root
hub's device node information after the device under root hub is created,
so this movement will not affect current function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Lars Steubesand <lars.steubesand@philips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary space before function pointer arguments.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:
[ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 13.183701] usb 3-3: device descriptor read/all, error -110
On a test system this failure occurred on 6% of all boots.
The call traces at the point of failure are:
Call Trace:
[<ffffffff81b9bab7>] schedule+0x37/0x90
[<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
[<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
[<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
[<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
[<ffffffff817d07de>] hub_port_init+0x51e/0xb70
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Call Trace:
[<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
[<ffffffff817fd87e>] xhci_address_device+0xe/0x10
[<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
[<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Which results from the two call chains:
hub_port_init
usb_get_device_descriptor
usb_get_descriptor
usb_control_msg
usb_internal_control_msg
usb_start_wait_urb
usb_submit_urb / wait_for_completion_timeout / usb_kill_urb
hub_port_init
hub_set_address
xhci_address_device
xhci_setup_device
Mathias Nyman explains the current behaviour violates the XHCI spec:
hub_port_reset() will end up moving the corresponding xhci device slot
to default state.
As hub_port_reset() is called several times in hub_port_init() it
sounds reasonable that we could end up with two threads having their
xhci device slots in default state at the same time, which according to
xhci 4.5.3 specs still is a big no no:
"Note: Software shall not transition more than one Device Slot to the
Default State at a time"
So both threads fail at their next task after this.
One fails to read the descriptor, and the other fails addressing the
device.
Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Init data marked const should be annotated with __initconst for
correctness and not __initdata. This also fixes LTO builds that
otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_vm_ops is used in devio.c only, so declare it as static
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb allocation will fail when usbtest_alloc_urb() tries to
allocate zero length buffer, but it doesn't need it in fact,
so just skips buffer allocation in the case.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NULL pointer dereferrence will happen when class driver
wants to allocate zero length buffer and pool_max[0]
can't be used, so simply returns NULL in the case.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the addition of VUDC, the USBIP stack can now be used on
configurations without USB host support, but trying to build
it with USB gadget support disabled fails with
drivers/usb/built-in.o: In function `vep_dequeue':
vudc_main.c:(.text+0xa6ddc): undefined reference to `usb_gadget_giveback_request'
drivers/usb/built-in.o: In function `nuke':
vudc_main.c:(.text+0xa6ea8): undefined reference to `usb_gadget_giveback_request'
drivers/usb/built-in.o: In function `vudc_device_reset':
vudc_main.c:(.text+0xa720c): undefined reference to `usb_gadget_udc_reset'
drivers/usb/built-in.o: In function `vudc_probe':
This addresses both issues, by changing the dependency for USBIP_CORE
to USB_COMMON, and adding additional dependencies on USB or USB_GADGET
for the individual portions as needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9360575c58 ("usbip: vudc: Add vudc to Kconfig")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a code fragment to ignore completing URBs in closing
connection.
Regarding this patch, 2 execution contexts are related.
1) stub_tx.c: stub_complete() which is called from USB core
1-1) add to unlink list and free URB or
1-2) move to tx list
2) stub_dev.c: stub_shutdown_connection() which is invoked by unbind
operation through sysfs.
2-1) stop TX/RX threads
2-2) close TCP connection and set ud.tcp_socket to NULL
2-3) cleanup pending URBs by stub_device_cleanup_urbs(sdev)
2-4) free unlink list (no lock)
In the race condition, URBs which will be cleared in 2-3) may be
handled in 1).
In case 1-1), it will not be transferred bcause tx threads are stooped
in 2-1).
In case 1-2), may be freed in 2-4).
With this patch, after 2-2), completing URBs in 1) will not be handled
and cleared in 2-3).
The kernel log with this patch is as below.
kernel: usbip_core: usbip_kernel_unlink:792: shutting down tcp_socket
ef61d980
kernel: usbip-host 1-3: free sdev f5df6180
kernel: usbip-host 1-3: free urb f5df6700
kernel: usbip-host 1-3: Enter
kernel: usbip_core: usbip_stop_eh:132: usbip_eh waiting completion 5
kernel: usbip_host: stub_complete:71: complete! status 0
kernel: usbip_host: stub_complete:102: ignore urb for closed connection
e725fc00 (*)
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725fc00 (**)
kernel: usbip-host 1-3: free urb e725e000
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725f800
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725e800
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: device reset
kernel: usbip-host 1-3: lock for reset
kernel: usbip_host: store_match_busid:178: del busid 1-3
kernel: uvcvideo: Found UVC 1.00 device Venus USB2.0 Camera (056e:700a)
kernel: input: Venus USB2.0 Camera as
/devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3:1.0/input/input22
(*) skipped with this patch in completion
(**) released in 2-3
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As find_endpoint() is a global funcion rename it to vudc_find_endpoint()
to clearly mark where does it come from.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL pointer dereference and obsolete comments forgotten when
usbip server was converted from an interface driver to a device driver.
Signed-off-by: Alexander Popov <alpopov@ptsecurity.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix WARN_ON() macro usage as suggested by Felipe.
Instead of using:
if (cond) {
WARN_ON(1);
do_stuff();
}
Use a better pattern with WARN_ON() placed in if condition:
if (WARN_ON(cond))
do_stuff();
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleanup in probe if we fail to get dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of DDMA mode we don't need to get an SOF interrupt so disable
the unmasking of SOF interrupt in DDMA mode.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is safety change added while doing slub debugging.
Affected functions:
dwc2_hcd_qtd_unlink_and_free()
_dwc2_hcd_urb_enqueue()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host slave mode, the core asserts the rxready, txfifoempty interrupts
that get serviced in the gadget irq handler. Prevent servicing of these
when not in the gadget mode of operation.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replaced the WARN_ON with a check and return of -EINVAL in the
dwc2_hsotg_ep_enable function if ep0 is passed in.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.
In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
whc_init already calls whc_clean_up if an error occurs during
the initialization, so calling it again if whc_init fails at
the end of wch_probe will cause double free errors. Fix this
by bailing out on an whc_init failure to a new label that avoids
doing the duplicated whc_clean_up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thanks to switching to devm_gpiod_get:
1) We don't have to pass fwnode pointer
2) We can request initial GPIO value at getting call
This was successfully tested on Netgear R6250 (BCM4708).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that there are no more users for
xhci_plat_type_is(), we can safely remove it.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the code has been refactored enough,
switching over to using ->plat_start() and
->init_quirk() becomes a very simple patch.
After this patch, there are no further uses for
xhci_plat_type_is() which will be removed in a
follow-up patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like RCAR's init_quirk() we want mvebu's to use
struct usb_hcd * as argument too. This is another
step towards removing xhci_plat_type_is().
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_plat_setup() is the rightful place for
xhci_mvebu_mbus_init_quirk(), so let's move it there
in order to make it simpler to get rid of
xhci_plat_type_is() later on.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
these two methods will be used to hide
platform-specific details so we can get rid of
xhci_plat_type_is() in a later patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're preparing to remove xhci_plat_type_is() in
favor of a better approach where we define function
pointers ahead of time. This will let us make
assumptions about which platforms we're running on
and which platform-specific functions we should call.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[delete extra comma in function parameters -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move duplicate code from xhci_queue_intr_tx()
and xhci_queue_isoc_tx_prepare() to the check_interval() function.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In drivers/usb/host/xhci-ring.c there are two functions
(xhci_queue_bulk_tx and queue_bulk_sg_tx) that are very similar,
so a lot of code duplication.
This patch merges these functions into to one xhci_queue_bulk_tx.
Also counting the needed TRBs is merged and refactored.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restructure usb_sg_cancel() so we don't have to disable interrupts
while cancelling the URBs.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_submit_urb() may take quite long to execute. For example, a
single sg list may have 30 or more entries, possibly leading to that
many calls to DMA-map pages. This can cause interrupt latency of
several hundred micro-seconds.
Avoid the problem by releasing the io->lock spinlock and re-enabling
interrupts before calling usb_submit_urb(). This opens races with
usb_sg_cancel() and sg_complete(). Handle those races by using
usb_block_urb() to stop URBs from being submitted after
usb_sg_cancel() or sg_complete() with error.
Note that usb_unlink_urb() is guaranteed to return -ENODEV if
!io->urbs[i]->dev and since the -ENODEV case is already handled,
we don't have to check for !io->urbs[i]->dev explicitly.
Before this change, reading 512MB from an ext3 filesystem on a USB
memory stick showed a throughput of 12 MB/s with about 500 missed
deadlines.
With this change, reading the same file gave the same throughput but
only one or two missed deadlines.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver to Kconfig to make it visible in menuconfig
and allow people to compile it.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sysfs attributes to allow controlling vudc from usbip tools.
dev_desc - device descriptor of current gadget. This is required to
be consisten with current usbip protocol and allow to list
exportable devices on given machine.
usbip_sockfd - allows to pass socket to kernel to start usbip transfer.
usbip_status - currnent status of device
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add endpoints definitions and ops for both endpoints and gadget.
Add also a suitable platform driver and functions for handling
usbip events.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains functions for returning requests to the client.
It also has functions that add requests completed in vudc_rx and
vudc_transfer to the return queue.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains a function that simulates USB traffic, based on
the one in dummy_hcd. Is also handles udc-directed control
requests, and contains functions for setting up and controlling
a timer for the emulation.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions which allows to receive urbs from the client.
It receives traffic in a loop in a separate thread.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add main vudc module file. This allows us to register suitable
platform device and driver (just like dummy_hcd does).
Currently number of vudc instances is determined using module
parameter but whole infrastructure is suitable to make vudc
creation dynamic (for example via configfs).
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add constants for VUDC events in usbip_common.h
and make use of them in usbip_common.c.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Small fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add header with definitions needed by vudc driver.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Some small improvements]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes here, just making sure our
storage driver uses a consistent multi-line comment
style.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 devices, because they are much newer, have much
less chance of having issues with larger transfers.
We still keep a limit because anything above 2048
sectors really rendered negligible speed
improvements, so we will simply ignore
that. Transferring 1MiB should already give us
pretty good performance.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just so we have some sort of documentation as to why
we limit our Mass Storage transfers to 240 sectors,
let's update the comment to make clearer that
devices were found that would choke with larger
transfers.
While at that, also make sure to clarify that other
operating systems have similar, albeit different,
limits on mass storage transfers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port can do 10 Gb/s the kernel should say so.
The corresponding check needs to be added.
Signed-off.by: Oliver Neukum <ONeukum@suse.com>>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_get_phy() function returns either a valid pointer to phy or
ERR_PTR() error, check for NULL always fails and may lead to oops on
error path, fix this issue.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2035772010.
Commit 20357720 claims throughput improvement for MSC/UVC, but I
don't see much improvement. Following are the MSC measurement using
dd on AM335x GP EVM.
with BCD_BH: read: 14.9MB/s, write: 20.9MB/s
without BCD_BH: read: 15.2MB/s, write: 21.2MB/s
However with this commit the following regressions have been observed.
1. ASIX usb-ethernet dongle is completely broken on UDP RX.
2. Unpluging a 3G modem, which uses option driver, behind a hub causes
console log flooding with the following message.
option_instat_callback: error -71
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions, such as f_sourcesink, rely on an endpoint's desc
field during their requests' complete() callback, so clear it only
_after_ nuking all requests to avoid NULL pointer dereference.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ftdi_sio_quirk structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding VID:PID for Straizona Focusers to cp210x driver.
Signed-off-by: Jasem Mutlaq <mutlaqja@ikarustech.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Coccinelle caught this instance of us kfree()ing
devm-allocated memory. The solution is just to not
do anything in our gadget_release.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This function compiles to 298 bytes of machine code, has ~10 callsites.
This is a USB 2.0 device, USB 2.0 is limited to ~40 MB/s, so should be
almost never CPU bound. No need to optimize for speed this agressively.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felipe Balbi <balbi@ti.com>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The previous code could use the first USB-DMAC with IPMMU if iommus
property was set into this device node. However, in this case, it
could not control the second USB-DMAC with IPMMU because a parameter
of IPMMU (micro-TLB id) is different with each USB-DMAC.
So, this patch uses the usb_gadget_{un}map_request_by_dev() APIs for
IPMMU. (Then, iommus property should be set into USB-DMAC node(s).)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsg_dma_map_ctrl() needs DMA device structure in the near future,
this patch changes arguments of dma_map_ctrl() to give such data.
(This patch is only change the argument.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsf_dma_{un}map() will use the "fifo" data in the near future,
this patch changes function call orfer in usbhsf_dma_prepare_push().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the following environment, the first argument of DMA API should
be set to a DMAC's device structure, not a udc controller's one.
- A udc controller needs an external DMAC device (like a DMA Engine).
- The external DMAC enables IOMMU.
So, this patch add usb_gadget_{un}map_request_by_dev() API to set
a DMAC's device structure by a udc controller driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The call to wusb_dev_sysfs_rm() which is just after return will never
be executed. On checking the code, wusb_dev_sysfs_add() is the last one
to be executed so even if that fails we do not need wusb_dev_sysfs_rm()
in the error path.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dear all,
1. Overview
In current USB/IP implementation, event kernel threads are created for
each port. The functions of the threads are closing connection and
error handling so they don't have not so many events to handle. There's
no need to have thread for each port.
BEFORE) vhci side - VHCI_NPORTS(8) threads are created.
$ ps aux | grep usbip
root 10059 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10060 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10061 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10062 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10063 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10064 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10065 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10066 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
BEFORE) stub side - threads will be created every bind operation.
$ ps aux | grep usbip
root 8368 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
root 8399 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
This patch put event threads of stub and vhci driver as one workqueue.
AFTER) only one event threads in each vhci and stub side.
$ ps aux | grep usbip
root 10457 0.0 0.0 0 0 ? S< 17:47 0:00 [usbip_event]
2. Modification to usbip_event.c
BEFORE) kernel threads are created in usbip_start_eh().
AFTER) one workqueue is created in new usbip_init_eh().
Event handler which was main loop of kernel thread is modified to
workqueue handler.
Events themselves are stored in struct usbip_device - same as before.
usbip_devices which have event are listed in event_list.
The handler picks an element from the list and wakeup usbip_device. The
wakeup method is same as before.
usbip_in_eh() substitutes statement which checks whether functions are
called from eh_ops or not. In this function, the worker context is used
for the checking. The context will be set in a variable in the
beginning of first event handling. usbip_in_eh() is used in event
handler so it works well.
3. Modifications to programs using usbip_event.c
Initialization and termination of workqueue are added to init and exit
routine of usbip_core respectively.
A. version info
v2)
# Merged 1/2 event handler itself and 2/2 user programs because of auto
build fail at 1/2 casued unmodified user programs in 1/2.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing checks for dma mapping error in qset_fill_page_list(),
I have missed two similar problems in qset_add_urb_sg() and
in qset_add_urb_sg_linearize().
v2: check validity of dma_addr with dma_mapping_error()
in qset_free_std() as suggested by Vladimir Zapolskiy.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
Reference: http://www.spinics.net/lists/linux-usb/msg21755.html
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sort IDs in groups to be easily found when needed.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems there are leftovers of some assignments which are not used
anymore. Compiler even warns us about:
drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]
Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
While here, convert PM ops to use modern API.
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the reserved fields of the SuperSpeed Plus Device Capability
descriptor to 0. Otherwise there might be stale data there which will
cause USB CV to fail.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64d513ac31 ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013
Cc: stable@vger.kernel.org # 4.4.x and 4.5.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that cannot work if R-Car Gen2/3 run on
above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some circumstances acm_tty_flush_chars() is called
with no buffer to flush. We simply need to do nothing.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as they
are "trivial".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJLLUACgkQMUfUDdst+ym3wgCeNSzb74ZskDbGsXUooE0XhYRc
iPoAnRpn/ahoBTzmkKiQXQ1+Br8pAUtN
=vyU/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vUqa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QLLF
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc3
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7ace8fc821 ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the state_changed variable into struct otg_fsm
so that we can support multiple instances.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each platform devices which is created by device tree, the default
DMA mask is set by of_dma_configure when the device are created. So
delete the redundant code at driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The host/device mode set with dr_mode should be kept all the time,
not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE
and CFGUSB_FORCEHOSTMODE bits).
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Przemek Rudy <prudy1@o2.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some new locking here, but missed an error path where we need
to unlock.
Fixes: 9acdf4df2f ('usb: gadget: f_midi: added spinlock on transmit function')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver can be crashed with devices that expose crafted descriptors
with too few endpoints.
See: http://seclists.org/bugtraq/2016/Mar/61
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: fix OOB endpoint check and add error messages ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack using the lack of sanity checking in probe is known. This
patch checks for the existence of a second port.
CVE-2016-3136
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
[johan: add error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b37d83a6a4 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.
The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.
This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:
"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
ep 129: using minimum values"
Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.
Fixes: b37d83a6a4
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
gcc warns about the use of regulators in phy_8x16_probe:
drivers/usb/phy/phy-qcom-8x16-usb.c: In function 'phy_8x16_probe':
drivers/usb/phy/phy-qcom-8x16-usb.c:284:13: error: 'regs[0].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:285:13: error: 'regs[1].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:286:12: error: 'regs[2].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
According to Mark Brown, this is the result of various abuses
of the PHY interfaces [1], so let's fix the driver instead.
This puts the regulator bulk data into the device structure so it
gets properly initialized and lets us call regulator_bulk_enable()
and regulator_bulk_disable() rather than open-coding them.
Setting the voltages the way the driver does is rather pointless
because for each regulator there is only one valid voltage
range, so that can just get set up in the DT. As there doesn't
seem to be any user of the newly added driver yet, we can simply
make sure the DTs are setting this up right when they get added.
I'm also fixing the handling of regulator_bulk_enable() failure.
Right now, the driver just ignores any failure, which doesn't make
sense, so I'm changing it to loudly complain (in case we actually
had a bug here) and error out.
Doing a fly-by review of the driver, I notice a couple of other
problems that I'm not addressing here:
- It really should not have been written as a USB PHY driver, but
instead should use the PHY subsystem.
- The DT compatible string does not follow the usual conventions,
and it should have a proper identifier in it rather than a wildcard.
- The example in the devicetree binding lists a register address
that is the same as the actual EHCI host controller in the SoC
as well as the otg-snps and the ci-hdrc device, which indicates
that these are probably not even distinct devices (or all but
one of them are wrong), and if more than one of them tries to
request the resources correctly, they fail.
[1] https://lkml.org/lkml/2016/1/26/267
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Access multi-byte fields of the SSP Dev Cap descriptor using the correct
endianness.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UDC driver should NEVER do anything behind
udc-core's back, so let's stop disabling endpoints
we don't exactly own - rather we provide as
resources for gadget drivers. This fixes the
regression reported by Gil.
Reported-by: Gil Weber <gil.weber@servelec-technologies.com>
Tested-by: Gil Weber <gil.weber@servelec-technologies.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since f_midi_transmit is called by both ALSA and USB sub-systems, it can
potentially cause a race condition between both calls because f_midi_transmit
is not reentrant nor thread-safe. This is due to an implementation detail that
the transmit function looks for the next available usb request from the fifo
and only enqueues it if there is data to send, otherwise just re-uses it. So,
if both ALSA and USB frameworks calls this function at the same time,
kfifo_seek() will return the same usb_request, which will cause a race
condition.
To solve this problem a syncronization mechanism is necessary. In this case it
is used a spinlock since f_midi_transmit is also called by usb_request->complete
callback in interrupt context.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: e1e3d7ec5d ("usb: gadget: f_midi: pre-allocate IN requests")
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJW8fPZAAoJENidgRMleOc9sc0P/2b4k8FiFwjMXiiXI1rcEjiz
ZjeVxzyAcwBiYoL8a2XONd+pihjLNcAbDbjk8SGUzmKDDz7elQbrhby/6o1dPlW/
fQEQFa8Xa8zhZgidO1AFc1DmIcPg/u/Z58wHbjIcqDjvzKA63213Ud34NJsRtF6y
+EJrIUZiTtj5q1pJgDmqlOv6ImmQtgW/AN51vNXCNNCyS9OsSgQm0DK5/f485HNc
2y5NE5hpijso69HFet5chuT3DiDLz/0dxmgCm/w9CRRzkHxYl3lxV/v07B+rZBo5
cWplFfvJqX7PvQtcP0sPPzZUfGT/vOeTboWprQwI4R3RObS18xLqlq6DEvOTmnqW
Jh+9uNBq4+kwSz5GcYjpwvj7+W0FPgIaBVRHrEW9qeXkgDpYloPtnEt8C8GmO6Bt
O0bgIzETq9mnRTA+VesIfjmTa4IYRDDUoDwGTw5CnW3jaZmtYJh8GhgZulMfPfyK
vfWQkY2OesXFwct0rU8tFiswTPeTRgXqL3AsPYjTPAHx1kfBpvfOQTCzzT7eSBr7
jykd9EXsXrYb/rpIxW7j6KjPpaWu+EouK06wc4TIBGrrWVTIV0ZvybzOBgf0FnpS
UDx87OyQb8x9TDMrfKf6bmJyly8y1dXkutFYY4XKIGUydlXIf0kn7AnIXW6SR7mX
fTEdLFMZ03ViCojtah5r
=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Here is a USB fix for the reported issue with 69bec72598 "USB: core:
let USB device know device node" as well as some other issues that have
been reported so far with this merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbsjB8ACgkQMUfUDdst+yn5BACeK0uVt+S/pr+HQE30j67b4UV6
TcMAn25xKshM73AFDm9ok9qKnWEEvkEt
=UgYu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a USB fix for the reported issue with commit 69bec72598
("USB: core: let USB device know device node") as well as some other
issues that have been reported so far with this merge window"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: uas: Reduce can_queue to MAX_CMNDS
USB: cdc-acm: more sanity checking
USB: usb_driver_claim_interface: add sanity checking
usb/core: usb_alloc_dev(): fix setting of ->portnum
USB: iowarrior: fix oops with malicious USB descriptors
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't matter
on it's own, but it seems like he is trying to get rid of all CURRENT_TIME
uses in file systems, which is a worthwhile goal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9HqT
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't
matter on it's own, but it seems like he is trying to get rid of all
CURRENT_TIME uses in file systems, which is a worthwhile goal.
* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
configfs: switch ->default groups to a linked list
configfs: Replace CURRENT_TIME by current_fs_time()
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots of
other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8/EACgkQMUfUDdst+ylsyQCgnVK6ZIFVPV9VijJvBIjxS3F+
fTMAoIMQwNrRMHQOq/lhxX00AgN0B9Ch
=2EQp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots
of other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (266 commits)
USB: core: let USB device know device node
usb: devio: Add ioctl to disallow detaching kernel USB drivers.
usb: gadget: f_acm: Fix configfs attr name
usb: udc: lpc32xx: remove USB PLL and USB OTG clock management
usb: udc: lpc32xx: remove direct access to clock controller registers
usb: udc: lpc32xx: switch to clock prepare/unprepare model
usb: renesas_usbhs: gadget: fix giveback status code in usbhsg_pipe_disable()
usb: gadget: renesas_usb3: Use ARCH_RENESAS
usb: dwc2: Fix issues in dwc2_complete_non_isoc_xfer_ddma()
usb: dwc2: Add support for Lantiq ARX and XRX SoCs
usb: phy: generic: Handle late registration of gadget
usb: gadget: bdc_udc: fix race condition in bdc_udc_exit()
usb: musb: core: added missing const qualifier to musb_hdrc_platform_data::config
usb: dwc2: Move host-specific core functions into hcd.c
usb: dwc2: Move register save and restore functions
usb: dwc2: Use kmem_cache_free()
usb: dwc2: host: If using uframe scheduler, end splits better
usb: dwc2: host: Totally redo the microframe scheduler
usb: dwc2: host: Properly set even/odd frame
usb: dwc2: host: Add dwc2_hcd_get_future_frame_number() call
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.6:
API:
- Convert remaining crypto_hash users to shash or ahash, also convert
blkcipher/ablkcipher users to skcipher.
- Remove crypto_hash interface.
- Remove crypto_pcomp interface.
- Add crypto engine for async cipher drivers.
- Add akcipher documentation.
- Add skcipher documentation.
Algorithms:
- Rename crypto/crc32 to avoid name clash with lib/crc32.
- Fix bug in keywrap where we zero the wrong pointer.
Drivers:
- Support T5/M5, T7/M7 SPARC CPUs in n2 hwrng driver.
- Add PIC32 hwrng driver.
- Support BCM6368 in bcm63xx hwrng driver.
- Pack structs for 32-bit compat users in qat.
- Use crypto engine in omap-aes.
- Add support for sama5d2x SoCs in atmel-sha.
- Make atmel-sha available again.
- Make sahara hashing available again.
- Make ccp hashing available again.
- Make sha1-mb available again.
- Add support for multiple devices in ccp.
- Improve DMA performance in caam.
- Add hashing support to rockchip"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: qat - remove redundant arbiter configuration
crypto: ux500 - fix checks of error code returned by devm_ioremap_resource()
crypto: atmel - fix checks of error code returned by devm_ioremap_resource()
crypto: qat - Change the definition of icp_qat_uof_regtype
hwrng: exynos - use __maybe_unused to hide pm functions
crypto: ccp - Add abstraction for device-specific calls
crypto: ccp - CCP versioning support
crypto: ccp - Support for multiple CCPs
crypto: ccp - Remove check for x86 family and model
crypto: ccp - memset request context to zero during import
lib/mpi: use "static inline" instead of "extern inline"
lib/mpi: avoid assembler warning
hwrng: bcm63xx - fix non device tree compatibility
crypto: testmgr - allow rfc3686 aes-ctr variants in fips mode.
crypto: qat - The AE id should be less than the maximal AE number
lib/mpi: Endianness fix
crypto: rockchip - add hash support for crypto engine in rk3288
crypto: xts - fix compile errors
crypto: doc - add skcipher API documentation
crypto: doc - update AEAD AD handling
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tPgH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Added support for some new video formats
- mn88473 DVB frontend driver got promoted from staging
- several improvements at the VSP1 driver
- several cleanups and improvements at the Media Controller
- added Media Controller support to snd-usb-audio. Currently, enabled
only for au0828-based V4L2/DVB boards
- Several improvements at nuvoton-cir: it now supports wake up codes
- Add media controller support to em28xx and saa7134 drivers
- coda driver now accepts NXP distributed firmware files
- Some legacy SoC camera drivers will be moving to staging, as they're
outdated and nobody so far is willing to fix and convert them to use
the current media framework
- As usual, lots of cleanups, improvements and new board additions.
* tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
