Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximum frame length check is enabled in lan937x switch on POR, But it
is found to be disabled on driver during port setup operation. Due to
this, packets are not dropped when transmitted with greater than configured
value. For testing, setup made for lan1->lan2 transmission and configured
lan1 interface with a frame length (less than 1500 as mentioned in
documentation) and transmitted packets with greater than configured value.
Expected no packets at lan2 end, but packets observed at lan2.
Based on the documentation, packets should get discarded if the actual
packet length doesn't match the frame length configured. Frame length check
should be disabled only for cascaded ports due to tailtags.
This feature was disabled on ksz9477 series due to ptp issue, which is
not in lan937x series. But since lan937x took ksz9477 as base, frame
length check disabled here as well. Patch added to remove this portion
from port setup so that maximum frame length check will be active for
normal ports.
Fixes: 55ab6ffaf3 ("net: dsa: microchip: add DSA support for microchip LAN937x")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Link: https://lore.kernel.org/r/20220912051228.1306074-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Changing the DSA master means different things depending on the tagging
protocol in use.
For NPI mode ("ocelot" and "seville"), there is a single port which can
be configured as NPI, but DSA only permits changing the CPU port
affinity of user ports one by one. So changing a user port to a
different NPI port globally changes what the NPI port is, and breaks the
user ports still using the old one.
To address this while still permitting the change of the NPI port,
require that the user ports which are still affine to the old NPI port
are down, and cannot be brought up until they are all affine to the same
NPI port.
The tag_8021q mode ("ocelot-8021q") is more flexible, in that each user
port can be freely assigned to one CPU port or to the other. This works
by filtering host addresses towards both tag_8021q CPU ports, and then
restricting the forwarding from a certain user port only to one of the
two tag_8021q CPU ports.
Additionally, the 2 tag_8021q CPU ports can be placed in a LAG. This
works by enabling forwarding via PGID_SRC from a certain user port
towards the logical port ID containing both tag_8021q CPU ports, but
then restricting forwarding per packet, via the LAG hash codes in
PGID_AGGR, to either one or the other.
When we change the DSA master to a LAG device, DSA guarantees us that
the LAG has at least one lower interface as a physical DSA master.
But DSA masters can come and go as lowers of that LAG, and
ds->ops->port_change_master() will not get called, because the DSA
master is still the same (the LAG). So we need to hook into the
ds->ops->port_lag_{join,leave} calls on the CPU ports and update the
logical port ID of the LAG that user ports are assigned to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is a desire to support for DSA masters in a LAG.
That configuration is intended to work by simply enslaving the master to
a bonding/team device. But the physical DSA master (the LAG slave) still
has a dev->dsa_ptr, and that cpu_dp still corresponds to the physical
CPU port.
However, we would like to be able to retrieve the LAG that's the upper
of the physical DSA master. In preparation for that, introduce a helper
called dsa_port_get_master() that replaces all occurrences of the
dp->cpu_dp->master pattern. The distinction between LAG and non-LAG will
be made later within the helper itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This node pointer is returned by of_find_compatible_node() with
refcount incremented in this function. of_node_put() on it before
exitting this function.
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220908040226.871690-1-sunke32@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477 has the 11 bit ageing count value which is split across the two
registers. And LAN937x has the 20 bit ageing count which is also split
into two registers. Each count in the registers represents 1 second.
This patch add the support for ageing time for KSZ9477 and LAN937x
series of switch.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch families supported by the ocelot lib (ocelot, felix, seville)
export the same registers so far. But for example felix also has TSN
counters, while the others don't.
To reduce the bloat even further, create an OCELOT_COMMON_STATS() macro
which just lists all stats that are common between switches. The array
elements are still replicated among all of vsc9959_stats_layout,
vsc9953_stats_layout and ocelot_stats_layout.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current definition of struct ocelot_stat_layout is long-winded (4
lines per entry, and we have hundreds of entries), so we could make an
effort to use the C preprocessor and reduce the line count.
Create an implicit correspondence between enum ocelot_reg, which tells
us the register address (SYS_COUNT_RX_OCTETS etc) and enum ocelot_stat
which allows us to index the ocelot->stats array (OCELOT_STAT_RX_OCTETS
etc), and don't require us to specify both when we define what stats
each switch family has.
Create an OCELOT_STAT() macro that pairs only an enum ocelot_stat to an
enum ocelot_reg, and an OCELOT_STAT_ETHTOOL() macro which also contains
a name exported to the unstructured ethtool -S stringset API. For now,
we define all counters as having the OCELOT_STAT_ETHTOOL() kind, but we
will add more counters in the future which are not exported to the
unstructured ethtool -S.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware counter is called C_TX_AGED, so rename SYS_COUNT_TX_AGING
to SYS_COUNT_TX_AGED. This will become important since we want to
minimize the way in which we declare struct ocelot_stat_layout elements,
using the C preprocessor.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is integrated with the new standardized ethtool -S --groups option,
but the felix driver only exports unstructured statistics.
Reuse the array of 64-bit statistics collected by ocelot_check_stats_work(),
but just export select values from it.
Since ocelot_check_stats_work() runs periodically to avoid 32-bit
overflow, and the ethtool calling context is sleepable, we update the
64-bit stats one more time, to provide up-to-date values. The locking
scheme with a mutex followed by a spinlock is a bit hard to digest, so
we create and use a ocelot_port_stats_run() helper with a callback that
populates the ethool stats group the caller is interested in.
The exported stats are:
ethtool -S swp0 --groups eth-phy
ethtool -S swp0 --groups eth-mac
ethtool -S swp0 --groups eth-ctrl
ethtool -S swp0 --groups rmon
ethtool --include-statistics --show-pause swp0
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the logic from the ocelot switchdev driver's ocelot_get_stats64()
method to the common switch lib and reuse it for the DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix PSFP counters suffer from the same problem as the ocelot
ndo_get_stats64 ones - they are 32-bit, so they can easily overflow and
this can easily go undetected.
Add a custom hook in ocelot_check_stats_work() through which driver
specific actions can be taken, and update the stats for the existing
PSFP filters from that hook.
Previously, vsc9959_psfp_filter_add() and vsc9959_psfp_filter_del() were
serialized with respect to each other via rtnl_lock(). However, with the
new entry point into &psfp->sfi_list coming from the periodic worker, we
now need an explicit mutex to serialize access to these lists.
We used to keep a struct felix_stream_filter_counters on stack, through
which vsc9959_psfp_stats_get() - a FLOW_CLS_STATS callback - would
retrieve data from vsc9959_psfp_counters_get(). We need to become
smarter about that in 3 ways:
- we need to keep a persistent set of counters for each stream instead
of keeping them on stack
- we need to promote those counters from u32 to u64, and create a
procedure that properly keeps 64-bit counters. Since we clear the
hardware counters anyway, and we poll every 2 seconds, a simple
increment of a u64 counter with a u32 value will perfectly do the job.
- FLOW_CLS_STATS also expect incremental counters, so we also need to
zeroize our u64 counters every time sch_flower calls us
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support SPI-controlled switches in the future, access to
SYS_STAT_CFG_STAT_VIEW needs to be done outside of any spinlock
protected region, but it still needs to be serialized (by a mutex).
Split the ocelot->stats_lock spinlock into a mutex that serializes
indirect access to hardware registers (ocelot->stat_view_lock) and a
spinlock that serializes access to the u64 ocelot->stats array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSN stream (802.1Qci, 802.1CB) filters are also accessed through
STAT_VIEW, just like the port registers, but these counters are per
stream, rather than per port. So we don't keep them in
ocelot_port_update_stats().
What we can do, however, is we can create register definitions for them
just like we have for the port counters, and delete the last remaining
user of the SYS_CNT register + a group index (read_gix).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set()
runs unlocked with respect to the other functions that access it, which
are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and
vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock,
so move the vsc9959_sched_speed_set() access under that lock as well, to
resolve the concurrency.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605,
frames even way larger than 601 octets are transmitted even though these
should be considered as oversized, according to the documentation, and
dropped.
Since oversized frame dropping depends on frame size, which is only
known at the EOF stage, and therefore not at SOF when cut-through
forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_*
into consideration for traffic classes that are cut-through.
Since cut-through forwarding has no UAPI to control it, and the driver
enables it based on the mantra "if we can, then why not", the strategy
is to alter vsc9959_cut_through_fwd() to take into consideration which
tc's have oversize frame dropping enabled, and disable cut-through for
them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the
cut-through determination process.
There are 2 strategies for vsc9959_cut_through_fwd() to determine
whether a tc has oversized dropping enabled or not. One is to keep a bit
mask of traffic classes per port, and the other is to read back from the
hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the
feature is enabled). We choose reading back from registers, because
struct ocelot_port is shared with drivers (ocelot, seville) that don't
support either cut-through nor tc-taprio, and we don't have a felix
specific extension of struct ocelot_port. Furthermore, reading registers
from the Felix hardware is quite cheap, since they are memory-mapped.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit broke tc-taprio schedules such as this one:
tc qdisc replace dev $swp1 root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 \
sched-entry S 0x7f 990000 \
sched-entry S 0x80 10000 \
flags 0x2
because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard
band added earlier than its 'gate close' event, such that packet
overruns won't occur in the worst case of the largest packet possible.
Since guard bands are statically determined based on the per-tc
QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU,
we need to discuss what happens with TC 7 depending on kernel version,
since the driver, prior to commit 55a515b1f5 ("net: dsa: felix: drop
oversized frames with tc-taprio instead of hanging the port"), did not
touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU.
1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to
1518, and at gigabit this introduces a static guard band (independent
of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit
time of 20 octets => 160 ns). But this is larger than the time window
itself, of 10000 ns. So, the queue system never considers a frame with
TC 7 as eligible for transmission, since the gate practically never
opens, and these frames are forever stuck in the TX queues and hang
the port.
2 (after vsc9959_tas_guard_bands_update): Under the sole goal of
enabling oversized frame dropping, we make an effort to set
QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays
one more role, which we did not take into account: per-tc static guard
band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead).
There is a discrepancy between what the driver thinks (that there is
no guard band, and 100% of min_gate_len[tc] is available for egress
scheduling) and what the hardware actually does (crops the equivalent
of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this
means that the hardware thinks it has exactly 0 ns for scheduling tc 7.
In both cases, even minimum sized Ethernet frames are stuck on egress
rather than being considered for scheduling on TC 7, even if they would
fit given a proper configuration. Considering the current situation,
with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230
octets in size are not eligible for oversized dropping (because they are
smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible
for scheduling either, because the min_gate_len[7] (10000 ns) minus the
guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per
octet == 9840 ns) minus the guard band auto-added for L1 overhead by
QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets)
leaves 0 ns for scheduling in the queue system proper.
Investigating the hardware behavior, it becomes apparent that the queue
system needs precisely 33 ns of 'gate open' time in order to consider a
frame as eligible for scheduling to a tc. So the solution to this
problem is to amend vsc9959_tas_guard_bands_update(), by giving the
per-tc guard bands less space by exactly 33 ns, just enough for one
frame to be scheduled in that interval. This allows the queue system to
make forward progress for that port-tc, and prevents it from hanging.
Fixes: 297c4de6f7 ("net: dsa: felix: re-enable TAS guard band mode")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the LAN9354 device by allowing it to use
the LAN9303 DSA driver. These devices have the same underlying
access and control methods and from a feature set point of view
the LAN9354 is a superset of the LAN9303.
The MDIO access method has been tested on a SAMA5D3-EDS board
with a LAN9354 RMII daughter card.
While the SPI access method should also be the same, it has not
been tested and as such is not included at this time.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial BYTE_ORDER read to sync the 32-bit accesses over the 16-bit
mdio bus to improve driver robustness.
The lan9303 expects two mdio read transactions back-to-back to read a
32-bit register. The first read transaction causes the other half of the
32-bit register to get latched. The subsequent read returns the latched
second half of the 32-bit read. The BYTE_ORDER register is an exception to
this rule. As it is a constant value, there is no need to latch the second
half. We read this register first in case there were reads during the boot
loader process that might have occurred prior to this driver taking over
ownership of accessing this device.
This patch has been tested on the SAMA5D3-EDS with a LAN9303 RMII daughter
card.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_get_match_data is called on priv->dev before priv->dev is
actually set. Move of_device_get_match_data after priv->dev is correctly
set to fix this kernel panic.
Fixes: 3bb0844e7b ("net: dsa: qca8k: cache match data to speed up access")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220904215319.13070-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the lan937x_reset_switch(), it masks all the switch and port
registers. In the Global_Int_status register, POR ready bit is write 1
to clear bit and all other bits are read only. So, this patch clear the
por_ready_int status bit by writing 1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ksz_port doesn't have reference to ksz_device as of now. In order
to find out from which port interrupt has triggered, we need to pass the
struct ksz_port as a host data. When the interrupt is triggered, we can
get the port from which interrupt triggered, but to identify it is phy
interrupt we have to read status register. The regmap structure for
accessing the device register is present in the ksz_device struct. To
access the ksz_device from the ksz_port, the reference is added to it
with port number as well.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.
Tested on KSZ8873 and KSZ9477.
Fixes: da8cd08520 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use chip_id as other places of this code do it
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used. So, remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used on ksz9477 side. Remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is unused. So, drop it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With code refactoring was introduced new variable internal_phy. Let's
use it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ9477
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why PHYlib may access MII_CTRL1000 on the chip without GBit
support is only if chip provides wrong information about extended caps
register. This issue is now handled by ksz9477_r_phy_quirks()
With proper regmap_ranges provided for all chips we will be able to
catch this kind of bugs any way. So, remove this sanity check.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ8563.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is complex driver with support for different chips with different
layouts. To detect at least some bugs earlier, we should validate register
accesses by using regmap_access_table support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding regmap register access validation.
KSZ9893 compatible chips do not have "Output Clock Control Register
0x0103". So, avoid writing to it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read*/ksz_write* are able to return errors, so forward it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY access may end with errors on different levels. So, allow to forward
return values where possible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding support of regmap_ranges for KSZ8563R
chip. This chip is reporting extended registers support without having
actual extended registers. This made PHYlib request not existing
registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 has two 100Mbit PHYs and CPU port with RGMII support. Since
1000Mbit configuration for the RGMII capable MAC is present, we should
use per port validation.
As main part of migration to per-port validation we need to rework
ksz9477_switch_init() function. Which is using undocumented
REG_GLOBAL_OPTIONS register to detect per-chip Gbit support. So, it is
related to some sort of risk for regressions.
To reduce this risk I compared the code with publicly available
documentations. This function will executed on following currently
supported chips:
struct ksz_chip_data OF compatible
KSZ9477 KSZ9477
KSZ9897 KSZ9897
KSZ9893 KSZ9893, KSZ9563
KSZ8563 KSZ8563
KSZ9567 KSZ9567
Only KSZ9893, KSZ9563, KSZ8563 document existence of 0xf ==
REG_GLOBAL_OPTIONS register with bit field description "SKU ID":
KSZ9893 0x0C
KSZ9563 0x1C
KSZ8563 0x3C
The existence of hidden flags is not documented.
KSZ9477, KSZ9897, KSZ9567 do not document this register at all.
Only KSZ8563 is documented as non Gbit chip: 100Mbit PHYs and RGMII CPU
port. So, this change should not introduce a regression for
configurations with properly used OF compatibles.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add separate entry for the KSZ8563 chip. According to the documentation
it can support Gbit only on RGMII port. So, we will need to be able to
describe in the followup patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xrs700x_read_port_counters() updates the stats from a worker using the
u64_stats_update_begin() version. This is okay on 32-UP since on the
reader side preemption is disabled.
On 32bit-SMP the writer can be preempted by the reader at which point
the reader will spin on the seqcount until writer continues and
completes the update.
Assigning the mib_mutex mutex to the underlying seqcount would ensure
proper synchronisation. The API for that on the u64_stats_init() side
isn't available. Since it is the only user, just use disable interrupts
during the update.
Use u64_stats_update_begin_irqsave() on the writer side to ensure an
uninterrupted update.
Fixes: ee00b24f32 ("net: dsa: add Arrow SpeedChips XRS700x driver")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
p0_mode set to one of the supported serial mode should not prevent
configuring the external SMI interface in
mv88e6xxx_g2_scratch_gpio_set_smi. The current masking of the p0_mode
only checks the first 2 bits. This results in switches supporting
serial mode cannot setup external SMI on certain serial modes
(Ex: 1000BASE-X and SGMII).
Extend the mask of the p0_mode to include the reduced modes and
serial modes as allowed modes for the external SMI interface.
Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220824093706.19049-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the probe defaults all interfaces to the highest speed possible
(10GBASE-X in mv88e6393x) before the phy mode configuration from the
devicetree is considered it is currently impossible to use port 0 in
RGMII mode.
This change will allow RGMII modes to be configurable for port 0
enabling port 0 to be configured as RGMII as well as serial depending
on configuration.
Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220822144136.16627-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a partial revert of commit c295f9831f ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bda ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an error occurs in dsa_devlink_region_create(), then 'priv->regions'
array will be accessed by negative index '-1'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: bf425b8205 ("net: dsa: sja1105: expose static config as devlink region")
Link: https://lore.kernel.org/r/20220817003845.389644-1-subkhankulov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the artificial limitations imposed upon
bcm_sf2_sw_mac_link_{up,down} and allow us to override the link
parameters for IMP port(s) as well as regular ports by accounting for
the special differences that exist there.
Remove the code that did override the link parameters in
bcm_sf2_imp_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending upon the generation of switches, we have different offsets for
configuring a given port's status override where link parameters are
applied. Introduce a helper function that we re-use throughout the code
in order to let phylink callbacks configure the IMP/CPU port(s) in
subsequent changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the port isn't a CPU port nor a user port, 'cpu_dp'
is a null pointer and a crash happened on dereferencing
it in mv88e6060_setup_port():
[ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014
...
[ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84
[ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54
[ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0
[ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c
[ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c
[ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0
[ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184
[ 9.986632] __device_attach from bus_probe_device+0x8c/0x94
[ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8
[ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c
[ 10.006292] process_one_work from worker_thread+0x30/0x4b8
[ 10.012155] worker_thread from kthread+0xd4/0x10c
[ 10.017238] kthread from ret_from_fork+0x14/0x3c
Fixes: 0abfd494de ("net: dsa: use dedicated CPU port")
CC: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220811070939.1717146-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The way in which dsa_tree_change_tag_proto() works is that when
dsa_tree_notify() fails, it doesn't know whether the operation failed
mid way in a multi-switch tree, or it failed for a single-switch tree.
So even though drivers need to fail cleanly in
ds->ops->change_tag_protocol(), DSA will still call dsa_tree_notify()
again, to restore the old tag protocol for potential switches in the
tree where the change did succeeed (before failing for others).
This means for the felix driver that if we report an error in
felix_change_tag_protocol(), we'll get another call where proto_ops ==
old_proto_ops. If we proceed to act upon that, we may do unexpected
things. For example, we will call dsa_tag_8021q_register() twice in a
row, without any dsa_tag_8021q_unregister() in between. Then we will
actually call dsa_tag_8021q_unregister() via old_proto_ops->teardown,
which (if it manages to run at all, after walking through corrupted data
structures) will leave the ports inoperational anyway.
The bug can be readily reproduced if we force an error while in
tag_8021q mode; this crashes the kernel.
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo edsa > /sys/class/net/eno2/dsa/tagging # -EPROTONOSUPPORT
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
Call trace:
vcap_entry_get+0x24/0x124
ocelot_vcap_filter_del+0x198/0x270
felix_tag_8021q_vlan_del+0xd4/0x21c
dsa_switch_tag_8021q_vlan_del+0x168/0x2cc
dsa_switch_event+0x68/0x1170
dsa_tree_notify+0x14/0x34
dsa_port_tag_8021q_vlan_del+0x84/0x110
dsa_tag_8021q_unregister+0x15c/0x1c0
felix_tag_8021q_teardown+0x16c/0x180
felix_change_tag_protocol+0x1bc/0x230
dsa_switch_event+0x14c/0x1170
dsa_tree_change_tag_proto+0x118/0x1c0
Fixes: 7a29d220f4 ("net: dsa: felix: reimplement tagging protocol change with function pointers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220808125127.3344094-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
min_gate_len[tc] is supposed to track the shortest interval of
continuously open gates for a traffic class. For example, in the
following case:
TC 76543210
t0 00000001b 200000 ns
t1 00000010b 200000 ns
min_gate_len[0] and min_gate_len[1] should be 200000, while
min_gate_len[2-7] should be 0.
However what happens is that min_gate_len[0] is 200000, but
min_gate_len[1] ends up being 0 (despite gate_len[1] being 200000 at the
point where the logic detects the gate close event for TC 1).
The problem is that the code considers a "gate close" event whenever it
sees that there is a 0 for that TC (essentially it's level rather than
edge triggered). By doing that, any time a gate is seen as closed
without having been open prior, gate_len, which is 0, will be written
into min_gate_len. Once min_gate_len becomes 0, it's impossible for it
to track anything higher than that (the length of actually open
intervals).
To fix this, we make the writing to min_gate_len[tc] be edge-triggered,
which avoids writes for gates that are closed in consecutive intervals.
However what this does is it makes us need to special-case the
permanently closed gates at the end.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220804202817.1677572-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same function to read the switch id is used by drivers based on
qca8k family switch. Move them to common code to make them accessible
also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port LAG functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port VLAN functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop exposing busy_wait and make it static.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port mirror functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port FDB/MDB function are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop bulk read/write functions and make them static
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same set age, MTU and port enable/disable function are used by
driver based on qca8k family switch.
Move them to common code to make them accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same bridge functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same logic to disable/enable port, set eee and get ethtool stats is
used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same mib function is used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same ATU function are used by drivers based on qca8k family switch.
Move the bulk read/write helper to common code to declare these shared
ATU functions in common code.
These helper will be dropped when regmap correctly support bulk
read/write.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same reg table and read/write/rmw function are used by drivers
based on qca8k family switch.
Move them to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same MIB struct is used by drivers based on qca8k family switch. Move
it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switch may not support mib autocast feature and require the legacy
way of reading the regs directly.
Make the mib autocast feature optional and permit to declare support for
it using match_data struct in a dedicated qca8k_info_ops struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using of_device_get_match_data is expensive. Cache match data to speed
up access and rework user of match data to use the new cached value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3c783b83bd ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
stopped relying on SPEED_MAX constant and hardcoded speed settings
for the switch ports and rely on phylink configuration.
It turned out, however, that when the relevant code is called,
the mac_capabilites of CPU/DSA port remain unset.
mv88e6xxx_setup_port() is called via mv88e6xxx_setup() in
dsa_tree_setup_switches(), which precedes setting the caps in
phylink_get_caps down in the chain of dsa_tree_setup_ports().
As a result the mac_capabilites are 0 and the default speed for CPU/DSA
port is 10M at the start. To fix that, execute mv88e6xxx_get_caps()
and obtain the capabilities driectly.
Fixes: 3c783b83bd ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220726230918.2772378-1-mw@semihalf.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent SPI warnings.
Fixes: 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-2-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent following warnings:
SPI driver sja1105 has no spi_device_id for nxp,sja1105e
SPI driver sja1105 has no spi_device_id for nxp,sja1105t
SPI driver sja1105 has no spi_device_id for nxp,sja1105p
SPI driver sja1105 has no spi_device_id for nxp,sja1105q
SPI driver sja1105 has no spi_device_id for nxp,sja1105r
SPI driver sja1105 has no spi_device_id for nxp,sja1105s
SPI driver sja1105 has no spi_device_id for nxp,sja1110a
SPI driver sja1105 has no spi_device_id for nxp,sja1110b
SPI driver sja1105 has no spi_device_id for nxp,sja1110c
SPI driver sja1105 has no spi_device_id for nxp,sja1110d
Fixes: 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6 ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary spi_set_drvdata() in b53_spi_remove(), the
driver_data will be set to NULL in device_unbind_cleanup() after
calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220705131733.351962-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
felix_vsc9959.c calls taprio_offload_get() and taprio_offload_free(),
symbols exported by net/sched/sch_taprio.c. As such, we must disallow
building the Felix driver as built-in when the symbol exported by
tc-taprio isn't present in the kernel image.
Fixes: 1c9017e44a ("net: dsa: felix: keep reference on entire tc-taprio config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220704190241.1288847-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time-sensitive networking code needs to work with PTP times expressed in
nanoseconds, and with packet transmission times expressed in
picoseconds, since those would be fractional at higher than gigabit
speed when expressed in nanoseconds.
Convert the existing uses in tc-taprio and the ocelot/felix DSA driver
to a PSEC_PER_NSEC macro. This macro is placed in include/linux/time64.h
as opposed to its relatives (PSEC_PER_SEC etc) from include/vdso/time64.h
because the vDSO library does not (yet) need/use it.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # for the vDSO parts
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, sending a packet into a time gate too small for it (or always
closed) causes the queue system to hold the frame forever. Even worse,
this frame isn't subject to aging either, because for that to happen, it
needs to be scheduled for transmission in the first place. But the frame
will consume buffer memory and frame references while it is forever held
in the queue system.
Before commit a4ae997adc ("net: mscc: ocelot: initialize watermarks to
sane defaults"), this behavior was somewhat subtle, as the switch had a
more intricately tuned default watermark configuration out of reset,
which did not allow any single port and tc to consume the entire switch
buffer space. Nonetheless, the held frames are still there, and they
reduce the total backplane capacity of the switch.
However, after the aforementioned commit, the behavior can be very
clearly seen, since we deliberately allow each {port, tc} to consume the
entire shared buffer of the switch minus the reservations (and we
disable all reservations by default). That is to say, we allow a
permanently closed tc-taprio gate to hang the entire switch.
A careful inspection of the documentation shows that the QSYS:Q_MAX_SDU
per-port-tc registers serve 2 purposes: one is for guard band calculation
(when zero, this falls back to QSYS:PORT_MAX_SDU), and the other is to
enable oversized frame dropping (when non-zero).
Currently the QSYS:Q_MAX_SDU registers are all zero, so oversized frame
dropping is disabled. The goal of the change is to enable it seamlessly.
For that, we need to hook into the MTU change, tc-taprio change, and
port link speed change procedures, since we depend on these variables.
Frames are not dropped on egress due to a queue system oversize
condition, instead that egress port is simply excluded from the mask of
valid destination ports for the packet. If there are no destination
ports at all, the ingress counter that increments is the generic
"drop_tail" in ethtool -S.
The issue exists in various forms since the tc-taprio offload was introduced.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vsc9959_tas_clock_adjust(), the INIT_GATE_STATE field is not changed,
only the ENABLE field. Similarly for the disabling of the time-aware
shaper in vsc9959_qos_port_tas_set().
To reflect this, keep the QSYS_TAG_CONFIG_INIT_GATE_STATE_M mask out of
the read-modify-write procedure to make it clearer what is the intention
of the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_parse_phandle() will increase the refcount of 'pcs_node', so add
of_node_put() before return from a5psw_pcs_get().
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220630014153.1888811-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6a ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commits add forwarding database support to the driver. It
implements fdb_add(), fdb_del() and fdb_dump().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics support to the rzn1-a5psw driver by implementing the
following dsa_switch_ops callbacks:
- get_sset_count()
- get_strings()
- get_ethtool_stats()
- get_eth_mac_stats()
- get_eth_ctrl_stats()
- get_rmon_stats()
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.
This driver includes basic bridging support, more support will be added
later (vlan, etc).
Suggested-by: Jean-Pierre Geslin <jean-pierre.geslin@non.se.com>
Suggested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 'commit 3506b2f42d ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
