The Synopsys DesignWare UART can be configured to have HW support for
the RS485 protocol from IP version 4.0 onward. Add support for
hardware-controlled half duplex and full duplex modes.
HW will take care of managing DE and RE, the driver just gives it
permission to use either by setting both to 1.
To ask for full duplex mode, userspace sets SER_RS485_RX_DURING_TX flag
and HW will take care of the rest.
Set delay_rts_before_send and delay_rts_after_send to zero for now. The
granularity of that ABI is too coarse to be useful.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UART_CAP_NOTEMT for UARTs that lack interrupt on TEMT but want to
use em485. Em485 framework needs to ensure not only FIFO is empty but
also that tx shift register is empty.
This approach uses Uwe Kleine-König's suggestion on simply
using/incrementing stop_tx timer rather than adding another timer. When
UART_CAP_NOTEMT is set and THRE is present w/o TEMT, stop tx timer is
reused to wait for the emptying of the shift register.
This change does not add the UART_CAP_NOTEMT define as it already exist
but is currently no-op. See 7a107b2c6b (Revert "serial: 8250: Handle
UART without interrupt on TEMT using em485") for further details.
Vicente Bergas reported that RTS is deasserted roughly one bit too
early losing stop bit tx. To address this problem, stop_delay now
accounts for one extra bit using rough formula /7 (assumes worst-case
of 2+5 bits). I suspect this glitch had to do with when THRE is getting
asserted. If FIFO is emptied already during the tx of the stop bit,
perhaps it leads to HW asserting THRE early for the normal frame time
formula to work accurately.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Eric Tremblay <etremblay@distech-controls.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 DMA tx complete path lacks calls to normal 8250 stop handling. It
does not use THRE to detect true completion of the tx and also doesn't
call __stop_tx. This leads to problems with em485 that needs to handle
RTS timing.
Instead of handling tx stop internally within 8250 dma code, enable
THRE when tx'able data runs out and tweak serial8250_handle_irq to call
only __stop_tx when uart is using DMA.
It also seems bit early to call serial8250_rpm_put_tx from there while
tx is still underway(?).
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct uart_port currently stores FIFO timeout. Having character timing
information readily available is useful. Even serial core itself
determines char_time from port->timeout using inverse calculation.
Store frame_time directly into uart_port. Character time is stored in
nanoseconds to have reasonable precision with high rates. To avoid
overflow, 64-bit math is necessary.
It might be possible to determine timeout from frame_time by
multiplying it with fifosize as needed but only part of the users seem
to be protected by a lock. Thus, this patch does not pursue storing
only frame_time in uart_port.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas RZ/N1 SoC features a slightly modified DW UART.
On this SoC, the CPR register value is known but not synthetized in
hardware. We hence need to provide a CPR value in the platform
data. This version of the controller also relies on acting as flow
controller when using DMA, so we need to provide the
"is dma flow controller" quirk.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW based controllers like the one on Renesas RZ/N1 must be programmed as
flow controllers when using DMA.
* Table 11.45 of the system manual, "Flow Control Combinations", states
that using UART with DMA requires setting the DMA in the peripheral
flow controller mode regardless of the direction.
* Chapter 11.6.1.3 of the system manual, "Basic Interface Definitions",
explains that the burst size in the above case must be configured in
the peripheral's register DEST/SRC_BURST_SIZE.
Experiments shown that upon Rx timeout, the DMA transaction needed to be
manually cleared as well.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These accessors should be used instead of the regular readl/writel()
helpers. In order to use them also from 8250_dw.c in this directory,
move the helpers to 8250_dwlib.h
There is no functional change.
There is no need for declaring `struct uart_port` or even UPIO_MEM32BE
which both are already included in the 8250_dwlib.h header by 8250.h.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a next change we are going to need the same Rx timeout condition as
we already have in the IRQ handling code. Let's just create a boolean to
clarify what this operation does before reusing it.
There is no functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One situation where this could be used is when configuring the UART
controller to be the DMA flow controller. This is a typical case where
the driver might need to program a few more registers before starting a
DMA transfer. Provide the necessary infrastructure to support this
case.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART controllers can be synthesized without the CPR register.
In this case, allow to the platform information to provide a CPR value.
Co-developed-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This offset is a good candidate to pdata's because it changes depending
on the vendor implementation. Let's move the usr_reg entry from regular
to pdata. This way we can drop initializing it at run time.
Let's also use a define for it instead of defining only the default
value.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use device tree match data rather than multiple calls to
of_device_is_compatible() by introducing a platform data structure and
adding a quirks mask.
Provide a stub to the compatibles without quirks to simplify the
handling of the upcoming changes.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
[<miquel.raynal@bootlin.com: Minor changes + creation of a real pdata structure]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the per-device structure and a helper out of the main .c file, into
a shared header as they will both be reused from another .c file.
There is no functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
[miquel.raynal@bootlin.com: Extracted from a bigger change]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 927728a34f.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for KGDB in stm32 serial driver by implementing characters
polling callbacks (poll_init, poll_get_char and poll_put_char).
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework stm32_usart_console_putchar() function in order to anticipate
the case where the character can never be sent.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not set timeout to twice the approximate amount of time to send the
entire FIFO if CTS is enabled. If the caller requested no timeout, e.g.
when userspace program called tcdrain(), then wait without any timeout.
Premature return from tcdrain() was observed on imx based system which
has 32 character long transmitter FIFO with hardware CTS handling.
Simple userspace application that reproduces problem has to:
* Open tty device, enable hardware flow control (CRTSCTS)
* Write data, e.g. 26 bytes
* Call tcdrain() to wait for the transmitter
* Close tty device
The other side of serial connection has to:
* Receive some data, e.g. 10 bytes
* Set RTS output (CTS input from sender perspective) inactive for
at least twice the port timeout
* Try to receive remaining data
Without this patch, userspace application will finish without any error
while the other side of connection will never receive remaining data.
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220228054911.1420221-1-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note: I am using a small test app + driver located at [0] for the
problem description. serco is a driver whose write function dispatches
to the serial controller. sertest is a user-mode app that writes n bytes
to the serial console using the serco driver.
While investigating a bug in the RHEL kernel, I noticed that the serial
console throughput is way below the configured speed of 115200 bps in
a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but
I got 2.5KB/s.
$ time ./sertest -n 2500 /tmp/serco
real 0m0.997s
user 0m0.000s
sys 0m0.997s
With the help of the function tracer, I then noticed the serial
controller was taking around 410us seconds to dispatch one single byte:
$ trace-cmd record -p function_graph -g serial8250_console_write \
./sertest -n 1 /tmp/serco
$ trace-cmd report
| serial8250_console_write() {
0.384 us | _raw_spin_lock_irqsave();
1.836 us | io_serial_in();
1.667 us | io_serial_out();
| uart_console_write() {
| serial8250_console_putchar() {
| wait_for_xmitr() {
1.870 us | io_serial_in();
2.238 us | }
1.737 us | io_serial_out();
4.318 us | }
4.675 us | }
| wait_for_xmitr() {
1.635 us | io_serial_in();
| __const_udelay() {
1.125 us | delay_tsc();
1.429 us | }
...
...
...
1.683 us | io_serial_in();
| __const_udelay() {
1.248 us | delay_tsc();
1.486 us | }
1.671 us | io_serial_in();
411.342 us | }
In another machine, I measured a throughput of 11.5KB/s, with the serial
controller taking between 80-90us to send each byte. That matches the
expected throughput for a configuration of 115200 bps.
This patch changes the serial8250_console_write to use the 16550 fifo
if available. In my benchmarks I got around 25% improvement in the slow
machine, and no performance penalty in the fast machine.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20220411174841.34936-2-wander@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some more serial drivers can be compile-tested under certain
circumstances (when building a specific architecture). So allow for
that.
This reduces the need of zillion mach/subarch-specific configs. And
since the 0day bot has only allmodconfig's for some archs, this
increases build coverage there too.
Note that cpm needs a minor update in the header, so that it drags in
at least some defines (CPM2 ones).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pic32_uart contains this:
#ifdef CONFIG_SERIAL_PIC32_CONSOLE
...
console_initcall(pic32_console_init);
...
core_initcall(pic32_late_console_init);
...
#endif
...
arch_initcall(pic32_uart_init);
When the driver is built as module, all three above become
module_init(). So if SERIAL_PIC32_CONSOLE is set while SERIAL_PIC32=m,
it results in the following build error:
In file included from include/linux/device/driver.h:21,
from include/linux/device.h:32,
from include/linux/platform_device.h:13,
from drivers/tty/serial/pic32_uart.c:12:
include/linux/module.h:131:49: error: redefinition of '__inittest'
So make sure SERIAL_PIC32_CONSOLE can be set only when SERIAL_PIC32=y --
similar as for other drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code wants to know if the circ buffer is empty, so use the proper
macro.
No functional change intended, just saner function name used for that
use case.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_port::membase is declared as a pointer. So it should be
initialized by NULL, not zero constant.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cache port->state->xmit into a local variable (xmit) in
cdns_uart_handle_tx(). This reduces length of some lines there
significantly. I.e. makes the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return from the true branch of the 'if'. This saves one indentation
level and makes the code more readable.
The two comments about what obvious code does are removed too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports this issue
sunplus-uart.c:501:26: warning: symbol 'sunplus_console_ports' was not declared. Should it be static?
sunplus_console_ports is only used in sunplus-uart.c so change
its storage-class specifier to static
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220421152505.1531507-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make UART driver compatible with S4 SOC UART. Meanwhile, the S4 SOC
UART uses 12MHz as the clock source for baud rate calculations.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220422111320.19234-3-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A /2 divider over XTAL was introduced since G12A, and is preferred
to be used over the still present /3 divider since it provides much
closer frequencies vs the request baudrate. Especially the BT module
uses 3Mhz baud rate. 8Mhz calculations can lead to baud rate bias,
causing some problems.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220422111320.19234-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some members of struct icom_port are completely unused or only set and
never read. Remove all those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_ops::release_port() and uart_ops::request_port() are not required
by the serial layer. So no need to define empty ones.
Remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() helper instead of explicit combo of
list_for_each() and list_entry().
Note that pos is used as a reference point in list_add_tail() in
icom_alloc_adapter(). This functionality remains as with an empty list,
cur_adapter_entry->icom_adapter_entry is still the list head.
This simplifies the code a bit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The baud rates are unsigned constants. So mark them as such.
Not only it makes sense, but they are passed also to
uart_get_baud_rate() and that expects unsigned int as baud rates on
input.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point keeping the header content separated. The header was
not even protected against double inclusion. So move the content to the
appropriate source file.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a lot of sparse warnings:
.../icom.c:228:30: warning: cast from restricted __le16
.../icom.c:232:66: warning: incorrect type in assignment (different base types)
.../icom.c:232:66: expected unsigned int [usertype] leBuffer
.../icom.c:232:66: got restricted __le32 [usertype]
.../icom.c:237:30: warning: cast from restricted __le16
...
.../icom.c:1228:22: warning: cast from restricted __le16
And they are correct. So sort them all out by using proper __leXX and
uXX types and the right direction of conversion: le16_to_cpu() instead
of cpu_to_le16(), where appropriate.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Integrate both the to_icom_adapter() macro and icom_kref_release()
wrapper into icom_remove_adapter(). (And keep it icom_kref_release()
name.)
It makes the code easier to follow without complex indirections.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In icom, there is an ICOM_PORT macro to perform upcasts from struct
uart_port to struct icom_port. It's not completely safe and it works
only because the first member of icom_port is uart_port. Nowadays, we
use container_of for such an upcast instead.
So introduce a helper (to_icom_port()) with container_of in it and
convert all the ICOM_PORT users to the new helper. Apart from the code
and type safety, it's also clear what icom_port (the variable) is.
Unlike with the old ICOM_PORT (the macro with the cast).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a preparation for cleaning up the omap1 headers, start
including linux/soc/ti/omap1-soc.h directly so we can
keep calling cpu_is_omap1510().
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This partially reverts commit f6f586102a. The code added by
that commit containted math overflow for 32-bit archs. In
addition, the approach used in it is unnecessarily complicated
requiring a dedicated timer just for notemt. A simpler approach
for providing UART_CAP_NOTEMT already exists (patches 1-2):
https://lore.kernel.org/linux-serial/20220411083321.9131-3-ilpo.jarvinen@linux.intel.com/T/#u
Thus, simply revert the UART_CAP_NOTEMT change for now.
There were two driver changes within the patch series adding
UART_CAP_NOTEMT taking advantage of the newly added flag.
This does not revert the driver changes and therefore also
UART_CAP_NOTEMT define has to remain. UART_CAP_NOTEMT remains
no-op until support is again added.
Fixes: f6f586102a ("serial: 8250: Handle UART without interrupt on TEMT using em485")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/5f874142-fb1f-bff7-f33-fac823e65e2e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX DMA drivers are device tree only, nothing in
include/linux/platform_data/dma-imx.h has platform_data in it, so move
the file to include/linux/dma/imx-dma.h.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220414162249.3934543-10-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 932d596378 ("serial: 8250: Return early in .start_tx() if there
are no chars to send") caused a regression where the drivers implementing
runtime PM stopped idling. This is because serial8250_rpm_put_tx() is now
unbalanced on early return, it normally gets called at __stop_tx().
Fixes: 932d596378 ("serial: 8250: Return early in .start_tx() if there are no chars to send")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220411111657.16744-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 76821e222c ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da9
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c ("serial: imx: ensure that RX irqs are off if RX is off")
Cc: stable@vger.kernel.org # 4.17
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220408233503.7251-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flow control is enabled, the UART should set RTS to false
during suspend to stop incoming data. Currently, the suspend
routine sets the mctrl register in the uart to zero, but leaves
the shadow version in the uart_port struct alone so that resume
can restore it. This causes a problem later in suspend when
serial8250_do_shutdown() is called which uses the shadow mctrl
register to clear some additional bits but ends up restoring RTS.
The solution is to clear RTS from the shadow version before
serial8250_do_shutdown() is called and restore it after.
Signed-off-by: Al Cooper <alcooperx@comcast.net>
Link: https://lore.kernel.org/r/20220324145620.41573-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Freescale variant of the 16550A doesn't have an interrupt on TEMT
available when using the FIFO mode.
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220330104642.229507-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce the UART_CAP_NOTEMT capability. The capability indicates that
the UART doesn't have an interrupt available on TEMT.
In the case where the device does not support it, we calculate the
maximum time it could take for the transmitter to empty the
shift register. When we get in the situation where we get the
THRE interrupt, we check if the TEMT bit is set. If it's not, we start
the a timer and recall __stop_tx() after the delay.
The transmit sequence is a bit modified when the capability is set. The
new timer is used between the last interrupt(THRE) and a potential
stop_tx timer.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
[moved to use added UART_CAP_TEMT]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
[moved to use added UART_CAP_NOTEMT, improve timeout]
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
[rebased to v5.17, making use of tty_get_frame_size]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220330104642.229507-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference.
Fixes: 54da3e381c ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404143842.16960-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port.
So remove the assignment from the drivers rs485_config() function to avoid
redundancy.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-10-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.
So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-9-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port.
So remove the assignment in the drivers rs485_config() function to avoid
reduncancy.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-8-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already nullifies the padding
field of the passed serial_rs485 struct before returning it to userspace.
Doing the same in the drivers rs485_config() function is redundant, so
remove the concerning memset in this function.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-7-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already clamps the RTS delays.
It also assigns the passed serial_rs485 struct to the uart port.
So remove these tasks from the drivers rs485_config() function to avoid
redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-6-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set.
So remove this check from the drivers rs485_config() function to avoid
redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-5-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.
So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_set_rs485_config() the serial core already
- ensures that only one of both options RTS on send or RTS after send is
set
- nullifies the padding field of the passed serial_rs485 struct
- clamps the RTS delays
- assigns the passed serial_rs485 struct to the uart port
So remove these tasks from the code of the drivers rs485_config() function
to avoid redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-3-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several drivers that support setting the RS485 configuration via userspace
implement one or more of the following tasks:
- in case of an invalid RTS configuration (both RTS after send and RTS on
send set or both unset) fall back to enable RTS on send and disable RTS
after send
- nullify the padding field of the returned serial_rs485 struct
- copy the configuration into the uart port struct
- limit RTS delays to 100 ms
Move these tasks into the serial core to make them generic and to provide
a consistent behaviour among all drivers.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to chip process differences, chip designers recommend using baud
rates as close to and larger as possible in order to reduce clock
errors.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220407081355.13602-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide information in the kernel log as to what configuration option to
enable for PCI UART devices that have been blacklisted in the generic
PCI 8250 UART driver and which have a dedicated driver available to
handle that has been disabled. The rationale is there is no easy way
for the user to map a specific PCI vendor:device pair to an individual
dedicated driver while the generic driver has this information readily
available and it will likely be confusing that the generic driver does
not register such a port.
This is unlike usual drivers, such as drivers/net/ethernet/3com/3c59x.c
which handles all the hardware family members regardless of differences
between them, and following an existing example where a serio driver
provides suggestions as to the correct configuration options to use:
psmouse serio1: synaptics: The touchpad can support a better bus than the too old PS/2 protocol. Make sure MOUSE_PS2_SYNAPTICS_SMBUS and RMI4_SMB are enabled to get a better touchpad experience.
A message is then printed like:
serial 0000:04:00.3: ignoring port, enable SERIAL_8250_PERICOM to handle
when an affected device is encountered and the generic driver rejects it.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203310054120.44113@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed for the Renesas RZ/V2M (r9a09g011) SoC.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220330154024.112270-6-phil.edworthy@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console_write and IRQ handler can run concurrently.
Problems may occurs console_write is continuously executed while
the IRQ handler is running.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20220407071619.102249-2-jaewon02.kim@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
altera_jtaguart_tx_chars() duplicates what altera_jtaguart_stop_tx()
already does. So instead of the duplication, call the helper instead.
Not only it makes the code cleaner, but it also says what the "if"
really does.
Cc: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flow control characters should be sent even if the TX is stopped. So fix
owl-uart to behave the same as other drivers.
This unification also allows the use of the TX helper in the future.
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code now contains:
#ifdef CONFIG_PPC_MPC512x
...
#endif
#ifdef CONFIG_PPC_MPC512x
...
#endif
So remove the endif+ifdef from the middle, provided it's about the same
define.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'remove-h8300' of git://git.infradead.org/users/hch/misc:
remove the h8300 architecture
This is clearly the least actively maintained architecture we have at
the moment, and probably the least useful. It is now the only one that
does not support MMUs at all, and most of the boards only support 4MB
of RAM, out of which the defconfig kernel needs more than half just
for .text/.data.
Guenter Roeck did the original patch to remove the architecture in 2013
after it had already been obsolete for a while, and Yoshinori Sato brought
it back in a much more modern form in 2015. Looking at the git history
since the reinstantiation, it's clear that almost all commits in the tree
are build fixes or cross-architecture cleanups:
$ git log --no-merges --format=%an v4.5.. arch/h8300/ | sort | uniq
-c | sort -rn | head -n 12
25 Masahiro Yamada
18 Christoph Hellwig
14 Mike Rapoport
9 Arnd Bergmann
8 Mark Rutland
7 Peter Zijlstra
6 Kees Cook
6 Ingo Molnar
6 Al Viro
5 Randy Dunlap
4 Yury Norov
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The below commit changed types of some hooks in struct psc_ops. It also
changed the types of the functions which are referenced in the instances
of the above struct.
However the commit did so only for CONFIG_PPC_MPC52xx, but not for
CONFIG_PPC_MPC512x. This results in build errors like:
mpc52xx_uart.c:static unsigned int mpc52xx_psc_raw_tx_rdy(struct uart_port *port)
mpc52xx_uart.c:static int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
^^^
mpc52xx_uart.c:static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
^^^
Therefore, fix the latter case now too.
Fixes: 18662a1d8f (tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned)
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220404055122.31194-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are
still creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkGznQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnFwCgwGD/syV+BH2krgY6cRixZz72vPsAn2RSnicd
2YUwSNCHoL+B7hvQMtDG
=A3X9
-----END PGP SIGNATURE-----
Merge tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are still
creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits)
vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE
serial: 8250: fix XOFF/XON sending when DMA is used
tty: serial: samsung: Add ARTPEC-8 support
dt-bindings: serial: samsung: Add ARTPEC-8 UART
serial: sc16is7xx: Clear RS485 bits in the shutdown
tty: serial: samsung: simplify getting OF match data
tty: serial: samsung: constify variables and pointers
tty: serial: samsung: constify s3c24xx_serial_drv_data members
tty: serial: samsung: constify UART name
tty: serial: samsung: constify s3c24xx_serial_drv_data
tty: serial: samsung: reduce number of casts
tty: serial: samsung: embed s3c2410_uartcfg in parent structure
tty: serial: samsung: embed s3c24xx_uart_info in parent structure
serial: 8250_tegra: mark acpi_device_id as unused with !ACPI
tty: serial: bcm63xx: use more precise Kconfig symbol
serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS
tty: serial: jsm: fix two assignments in if conditions
tty: serial: jsm: remove redundant assignments to variable linestatus
serial: 8250_mtk: make two read-only arrays static const
serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f16 (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the UART block on the ARTPEC-8 SoC. This is closely
related to the variants used on the Exynos chips. The register layout
is identical to Exynos850 et al but the fifo size is different (64 bytes
in each direction for all instances).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220311094515.3223023-3-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We tested RS485 function on an EVB which has SC16IS752, after
finishing the test, we started the RS232 function test, but found the
RTS is still working in the RS485 mode.
That is because both startup and shutdown call port_update() to set
the EFCR_REG, this will not clear the RS485 bits once the bits are set
in the reconf_rs485(). To fix it, clear the RS485 bits in shutdown.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220308110042.108451-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code with of_device_get_match_data() and use dev_of_node()
to remove ifdef-erry.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-9-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify variables, data pointed by several pointers and
"udivslot_table" static array. This makes code a bit safer.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-8-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver data (struct s3c24xx_serial_drv_data) is never modified, so
also its members can be made const. Except code style this has no
impact because the structure itself is always a const.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-7-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART name from driver data holds only string literals.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver data (struct s3c24xx_serial_drv_data) is only used to
initialize the driver properly and is not modified. Make it const.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointers to instances of "struct s3c24xx_serial_drv_data" are first
cast to kernel_ulong_t and then either used directly
(in "platform_device_id.driver_data") or cast again to void * (in
"of_device_id.data").
One cast can be dropped, so at least for "of_device_id.data" case there
will be no casts at all. This makes the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed "struct s3c2410_uartcfg" directly as a member of "struct
s3c24xx_serial_drv_data" instead of keeping it as a pointer. This makes
the code clearer (obvious ownership of "s3c2410_uartcfg
s3c24xx_serial_drv_data") and saves one pointer.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed "struct s3c24xx_uart_info" directly as a member of "struct
s3c24xx_serial_drv_data" instead of keeping it as a pointer. This makes
the code clearer (obvious ownership of "struct s3c24xx_serial_drv_data")
and saves one pointer.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's acpi_device_id table is referenced via ACPI_PTR() so it
will be unused for !CONFIG_ACPI builds:
drivers/tty/serial/8250/8250_tegra.c:178:36:
warning: ‘tegra_uart_acpi_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308074157.113568-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sunplus serial ports are only present on Sunplus SoCs. Hence add a
dependency on ARCH_SUNPLUS, to prevent asking the user about this driver
when configuring a kernel without Sunplus SoC support.
Fixes: 9e8d547032 ("serial: sunplus-uart: Add Sunplus SoC UART Driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59f46272ab5b16853acac4d585c3333cfd394223.1647352195.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable linestatus is being assigned values that are never read, the
assignments are redundant and can be removed.
Cleans up clang scan warnings:
drivers/tty/serial/jsm/jsm_cls.c:369:2: warning: Value stored to
'linestatus' is never read [deadcode.DeadStores]
drivers/tty/serial/jsm/jsm_cls.c:400:4: warning: Value stored to
'linestatus' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220307153047.139639-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the read-only arrays fraction_L_mapping and
fraction_M_mapping on the stack but instead make them static
const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220307230055.168241-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c15c3747ee (serial: samsung: fix potential soft lockup
during uart write) added an unlock of port->lock before
uart_write_wakeup() and a lock after it. It was always problematic to
write data from tty_ldisc_ops::write_wakeup and it was even documented
that way. We fixed the line disciplines to conform to this recently.
So if there is still a missed one, we should fix them instead of this
workaround.
On the top of that, s3c24xx_serial_tx_dma_complete() in this driver
still holds the port->lock while calling uart_write_wakeup().
So revert the wrap added by the commit above.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Hyeonkook Kim <hk619.kim@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220308115153.4225-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's only a wrapper to struct uart_port, so unwrap the whole code.
No change in functionality is intended.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220307054348.31748-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
So return 1 from kgdboc_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Fixes: 1bd54d851f ("kgdboc: Passing ekgdboc to command line causes panic")
Fixes: f2d937f3bf ("consoles: polling support, kgdboc")
Cc: He Zhe <zhe.he@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-serial@vger.kernel.org
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220309033018.17936-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'kgdboc_earlycon_init' looks for boot console that has both .read
and .write callbacks. Adds 'samsung_early_read' to samsung_tty.c's early
console to support kgdboc.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Woody Lin <woodylin@google.com>
Link: https://lore.kernel.org/r/20220302114923.144523-1-woodylin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: b7e2b5360f ("serial: mvebu-uart: implement UART clock driver for configuring UART base clock")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220301075806.3950108-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let serial core know that the chip automatically handles RTS/CTS signal.
This elimines completely unnecessary I2C/SPI bus traffic.
Cease reading from RX FIFO (by disabling RDI interrupt) when throttled.
Eventually the FIFO will fill up and the device will drive RTS output
inactive. Unthrottle by enabling back RDI interrupt.
Indirectly controlling RTS via RX FIFO state seems to be the only option
because RTS bit is ignored when hardware flow control is enabled.
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220301060332.2561851-4-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_handle_cts_change() and uart_handle_dcd_change() must be called
with port lock being held. Acquire the lock after reading MSR register.
Do not acquire spin lock when reading MSR register because I2C/SPI port
functions cannot be called with spinlocks held.
Update rng and dsr counters. Wake up delta_msr_wait to allow tty notice
modem status change.
Co-developed-by: Lech Perczak <l.perczak@camlintechnologies.com>
Co-developed-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220301060332.2561851-3-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sc16is7xx_stop_tx() clears THRI bit and thus disables THRI interrupt.
This makes it possible for transmission to cease indefinitely when more
than 64 characters are being sent.
The sc16is7xx_handle_tx() call executed by sc16is7xx_tx_proc() can send
up to FIFO length (64) characters. If more characters are written to the
output buffer, then the THRI interrupt is needed.
Solve the issue by enabling THRI interrupt in sc16is7xx_tx_proc().
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220301060332.2561851-2-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts the following commits:
31979060cc tty: serial: meson: Fix the compile link error reported by kernel test robot
5427c352a9 tty: serial: meson: Added S4 SOC compatibility
19b2ba0baf tty: serial: meson: The system stuck when you run the stty command on the console to change the baud rate
e5fc2b9984 tty: serial: meson: Make some bit of the REG5 register writable
44023b8e1f tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame
6436dd8f9b tty: serial: meson: Use devm_ioremap_resource to get register mapped memory
841f913e77 tty: serial: meson: Move request the register region to probe
They seem to cause lots of problems with existing hardware platforms,
and caused build issues, so revert the whole series all at once.
Link: https://lore.kernel.org/r/849a95fd-ae81-9a3b-0c06-dd7826af9eb2@baylibre.com
Link: https://lore.kernel.org/all/20220225073922.3947-1-yu.tu@amlogic.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yu Tu <yu.tu@amlogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describes the calculation of the UART baud rate clock using a clock
frame. Forgot to add in Kconfig kernel test Robot compilation error
due to COMMON_CLK dependency.
Fixes: 44023b8e1f ("tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220228064910.11636-1-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Sunplus SoC UART Driver.
SP7021 UART block contains 5 UARTs.
There are UART0~4 that supported in SP7021, the features list as below.
Support Full-duplex communication.
Support data packet length configurable.
Support stop bit number configurable.
Support force break condition.
Support baud rate configurable.
Support error detection and report.
Support RXD Noise Rejection Vote configurable.
UART0 pinout only support TX/RX two pins.
UART1 to UART4 pinout support TX/RX/CTS/RTS four pins.
Normally UART0 used for kernel console, also can be used for normal uart.
Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port.
UART driver probe will create path named "/dev/ttySUPx".
https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
Fixes: b86f86e8e7 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start the console and run the following commands in turn:
stty -F /dev/ttyAML0 115200 and stty -F /dev/ttyAML0 921600. The
system will stuck.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-6-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the internal clock source mux and divider writeable, allowing the
uart to deviate from the settings intially applied by the ROMCode and
using the most appropriate clocks.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-5-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the common Clock code to describe the UART baud rate clock
makes it easier for the UART driver to be compatible with the
baud rate requirements of the UART IP on different meson chips.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-4-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace devm_request_mem_region and devm_ioremap with
devm_ioremap_resource to make the code cleaner.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-3-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simplifies resetting the UART controller during probe
and will make it easier to integrate the common clock code
which will require the registers at probe time as well.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small n_gsm and sc16is7xx serial driver fixes for
5.17-rc6.
The n_gsm fixes are from Siemens as it seems they are using the line
discipline and fixing up a number of issues they found in their testing.
The sc16is7xx serial driver fix is for a reported problem with that
chip.
All of these have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYhjWlA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylUvgCeKicl7AbY+7/eYmRhaCisJhgzf8UAmQHA7RWB
HwcKv7yb49UYJHhbTyis
=F9Sx
-----END PGP SIGNATURE-----
Merge tag 'tty-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small n_gsm and sc16is7xx serial driver fixes for
5.17-rc6.
The n_gsm fixes are from Siemens as it seems they are using the line
discipline and fixing up a number of issues they found in their
testing. The sc16is7xx serial driver fix is for a reported problem
with that chip.
All of these have been in linux-next with no reported problems"
* tag 'tty-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: Fix for incorrect data being transmitted
tty: n_gsm: fix deadlock in gsmtty_open()
tty: n_gsm: fix wrong modem processing in convergence layer type 2
tty: n_gsm: fix wrong tty control line for flow control
tty: n_gsm: fix NULL pointer access due to DLCI release
tty: n_gsm: fix proper link termination after failed open
tty: n_gsm: fix encoding of command/response bit
tty: n_gsm: fix encoding of control signal octet bit DV
The code uses uart_amba_port::port on many places. Sometimes it even
needs not uart_amba_port itself. So simplify the code on many places
and remove the need of uart_amba_port on some places completely.
No functional changes intended. The objdump -d output shows only a code
move in pl010_rx_chars().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220224111028.20917-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hello print among with version and name definitions. Drivers
should print nothing if they are successful.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All these return bitmasks, so it makes more sense to return unsigned --
this is what a reader and also all the callers expect.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 9a1870ce81 ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3d ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 90b9aacf91 ("serial: 8250_pci: add Intel Tangier support")
Fixes: f549e94eff ("serial: 8250_pci: add Intel Penwell ports")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Depends-on: d9eda9bab2 ("serial: 8250_pci: Intel MID UART support to its own driver")
Link: https://lore.kernel.org/r/20220215100920.41984-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coccinelle report:
./drivers/tty/serial/8250/8250_aspeed_vuart.c:85:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:174:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:127:8-16:
WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Link: https://lore.kernel.org/r/fed40753603dac4d14b17970c88e6f5f936348c1.1644541843.git.yang.guang5@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the Kconfig help text for SERIAL_8250_LPSS, SERIAL_8250_MID and
SERIAL_8250_PERICOM configuration options for dedicated PCI UART drivers
that have been blacklisted in the generic PCI 8250 UART driver and as
from commit a13e19cf3d ("serial: 8250_lpss: split LPSS driver to
separate module"), commit d9eda9bab2 ("serial: 8250_pci: Intel MID
UART support to its own driver"), and commit fcfd3c09f4 ("serial:
8250_pci: Split out Pericom driver") respectively are not handled by
said driver anymore (rather than for extra features only, as the current
text indicates), and therefore require the respective dedicated drivers
to work at all.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2202121704560.34636@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement simple usage of fractional divisor. When main divisor D is too
large to represent requested baudrate then use divisor M from the
fractional divisor feature. All the M prescalers are set to the same and
maximal value 63, so the fractional part of the fractional divisor is not
used at all. We also determine upper limit for possible baudrates.
Experiments show that UART at baudrate 1500000 Bd with this configuration
is stable. So there is no need to implement complicated calculation of
fractional coefficients yet.
To use this feature with higher baudrates, it is required to use UART clock
provided by UART clock driver. Default boot xtal clock is not capable of
higher baudrates.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-6-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a new device driver for controlling UART clocks on Marvell
Armada 3700 SoC. This device driver is loaded for devices which match
the compatible string "marvell,armada-3700-uart-clock".
There are more pitfalls related to UART clocks:
- both UARTs use same parent clock source (which can be xtal or one of
the TBG clocks),
- if a TBG clock is used as the parent clock, there are two additional
divisors that can both be configured to divide the rate by 1, 2, ... 6,
but these divisors are again shared between the two UART controllers
on the SOC,
- the configuration of the parent clock source and divisors is done in
the address space of the first UART controller, UART1. Clocks can be
gated separately for UART1 and UART2, but this setting also lives in
the address space of UART1,
- Marvell's Functional Specification for Armada 3720 document has the
clock gating bits swapped, so the one described to gate UART1 clock
actually gates UART2 and vice versa,
- each UART has it's own "special divisor", and this uses the parent
clock described above. These divisors are configure in each UART's
address space separately.
Thus the driver for UART2 controller needs to have access to UART1
address space, since UART1 address space contains some bits exclusive
for UART2 and also some bits which are shared between UART1 and UART2.
Also, during boot, when early console is active on one of the UARTs,
and we want to switch parent clock from xtal (default) to TBG (to be
more flexible with baudrates), the driver changing UART clocks also
needs to be able to change the "special divisor", so that the baudrate
of earlycon is not changed when swtiching to normal console. Thus the
clock driver also needs to be able to access UART2 register space,
for UART2's "special divisor".
For these reasons, this new UART clock driver does not use
ioremap_resource(), but only ioremap() to prevent resource conflicts
between UART clock driver and UART driver.
We need to share only two 32-bit registers between the UART driver and
the UART clock driver:
- UART Clock Control
- UART 2 Baud Rate Divisor
Access to these two registers are protected by one spinlock to prevent
any conflicts. Access is required only during probing, when changing
baudrate or during suspend/resume.
Hardware can be configured to use one of following clocks as UART parent
clock: TBG-A-P, TBG-B-P, TBG-A-S, TBG-B-S, xtal. Not every clock is
usable for higher buadrates. Any subset can be specified in the
device-tree and the driver will choose the best one which also still
supports the mandatory baudrate of 9600 Bd. For smooth boot log output
it is needed to specify clock used by early console, otherwise garbage
would be printed on UART during probe of UART clock driver and
transitioning from early console to normal console.
We are implementing this to be able to configure TBG clock as UART
parent clock, which is required to be able to achieve higher baudrates
than 230400 Bd. We achieve this by referencing this new UART clock
device node in UART's device node. UART clock device driver
automatically chooses the best clock source for UART driver.
Until now, UART's device-tree node needed to reference one of the static
clocks (xtal or one of the TBGs) as parent clock in the `clocks`
phandle - the parent clock which was configured before booting the
kernel. If bootloader changed UART's parent clock, it needed to change
the `clocks` phandle in DTB correspondingly before booting.
From now on both the old mechanism (xtal or TBG referenced as parent
clock in `clocks` phandle) and the new one (UART clock referenced in the
`clocks` phandle) are supported, to provide full backward compatibility
with existing DTS files, full backward compatibility with existing boot
loaders, and to provide new features (runtime clock configuration to
allow higher baudrates than 230400 Bd). New features are available only
with new DTS files.
There was also a discussion about how the UART node and the
clock-controller node could be wrapped together in a new binding [1, 2].
As explained there, this is not possible if we want to keep backwards
compatibility with existing bootloaders, and thus we are doing this by
putting the UART clock-controller node inside the UART1 node.
[1] https://lore.kernel.org/linux-serial/20220120000651.in7s6nazif5qjkme@pali/
[2] https://lore.kernel.org/linux-serial/20220125204006.A6D09C340E0@smtp.kernel.org/
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-4-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export only the GPIOs that are not shared with hardware modem control
lines. Introduce new device parameter indicating whether modem control
lines are available.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-4-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTS, DTR and LOOP bits can be updated in a single MCR register update.
This reduces the number of (slow) SPI/I2C bus transactions.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-3-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preserve unaffected bits state when accessing EFR register. This
prevents hardware flow control bits from being cleared on enhanced
functions access.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-2-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't start the whole chain for TX if there is no data to send. This is
mostly relevant for rs485 mode as there might be rts-before-send and
rts-after-send delays involved.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220217211839.443039-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART drivers are meant to use the port spinlock within certain
methods, to protect against reentrancy. The sc16is7xx driver does
very little locking, presumably because when added it triggers
"scheduling while atomic" errors. This is due to the use of mutexes
within the regmap abstraction layer, and the mutex implementation's
habit of sleeping the current thread while waiting for access.
Unfortunately this lack of interlocking can lead to corruption of
outbound data, which occurs when the buffer used for I2C transmission
is used simultaneously by two threads - a work queue thread running
sc16is7xx_tx_proc, and an IRQ thread in sc16is7xx_port_irq, both
of which can call sc16is7xx_handle_tx.
An earlier patch added efr_lock, a mutex that controls access to the
EFR register. This mutex is already claimed in the IRQ handler, and
all that is required is to claim the same mutex in sc16is7xx_tx_proc.
See: https://github.com/raspberrypi/linux/issues/4885
Fixes: 6393ff1c44 ("sc16is7xx: Use threaded IRQ")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20220216160802.1026013-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 54da3e381c ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to
set up register mapping") fixed a bug that had, as a side-effect,
prevented the 8250_aspeed_vuart driver from enabling the VUART's
FIFOs. However, fixing that (and hence enabling the FIFOs) has in
turn revealed what appears to be a hardware bug in the ASPEED VUART in
which the host-side THRE bit doesn't get if the BMC-side receive FIFO
trigger level is set to anything but one byte. This causes problems
for polled-mode writes from the host -- for example, Linux kernel
console writes proceed at a glacial pace (less than 100 bytes per
second) because the write path waits for a 10ms timeout to expire
after every character instead of being able to continue on to the next
character upon seeing THRE asserted. (GRUB behaves similarly.)
As a workaround, introduce a new port type for the ASPEED VUART that's
identical to PORT_16550A as it had previously been using, but with
UART_FCR_R_TRIG_00 instead to set the receive FIFO trigger level to
one byte, which (experimentally) seems to avoid the problematic THRE
behavior.
Fixes: 54da3e381c ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Tested-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220211004203.14915-1-zev@bewilderbeest.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All supported platforms by this driver require ->setup() and ->exit().
Remove unneeded test for ->setup() presence.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220215101111.47250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace MID_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220215104126.7220-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add early console support which relies on the bootloader for the
initialization of the UART.
Please note, that the compatibles are taken from at91-usart MFD
driver.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220217094620.1148571-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix miscompilations when function calls are made from inside a
put_user() call
- Drop __init from map_pages() declaration to avoid random boot crashes
- Added #error messages if a 64-bit compiler was used to build a 32-bit
kernel (and vice versa)
- Fix out-of-bound data TLB miss faults in sba_iommu and ccio-dma
drivers
- Add ioread64_lo_hi() and iowrite64_lo_hi() functions to avoid kernel
test robot errors
- Fix link failure when 8250_gsc driver is built without CONFIG_IOSAPIC
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYgu/DwAKCRD3ErUQojoP
X5+oAP4qsrVJZHrzalqJoGlDHZKGRKH5b9t5JQb09d1XmgFcZgD5AedIEX3sIS4X
zOIY5500TQqqbqLn7pvQDXYc1S7LtgM=
=Zwfn
-----END PGP SIGNATURE-----
Merge tag 'for-5.17/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- Fix miscompilations when function calls are made from inside a
put_user() call
- Drop __init from map_pages() declaration to avoid random boot crashes
- Added #error messages if a 64-bit compiler was used to build a 32-bit
kernel (and vice versa)
- Fix out-of-bound data TLB miss faults in sba_iommu and ccio-dma
drivers
- Add ioread64_lo_hi() and iowrite64_lo_hi() functions to avoid kernel
test robot errors
- Fix link failure when 8250_gsc driver is built without CONFIG_IOSAPIC
* tag 'for-5.17/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
serial: parisc: GSC: fix build when IOSAPIC is not set
parisc: Fix some apparent put_user() failures
parisc: Show error if wrong 32/64-bit compiler is being used
parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
parisc: Fix sglist access in ccio-dma.c
parisc: Fix data TLB miss in sba_unmap_sg
parisc: Drop __init from map_pages declaration
There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:
hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'
when:
CONFIG_GSC=y
CONFIG_SERIO_GSCPS2=y
CONFIG_SERIAL_8250_GSC=y
CONFIG_PCI is not set
and hence PCI_LBA is not set.
IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.
Make the use of iosapic_serial_irq() conditional to fix the build error.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now, even when `delay_rts_before_send` and `delay_rts_after_send`
are 0, the hrtimer is triggered (with timeout 0) which can introduce a
few 100us of additional overhead on slower i.MX platforms.
Implement a fast path when the delays are 0, where the RTS signal is
toggled immediately instead of going through an hrtimer. This fast path
behaves identical to the code before delay support was implemented.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Link: https://lore.kernel.org/r/20220119145204.238767-1-hws@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI support to 8250_bcm2835aux driver. This makes it possible to
use the miniuart on the Raspberry Pi with the tianocore/edk2 UEFI
firmware.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20220207232129.402882-1-athierry@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable mctrl_gpio wake_irq if device_may_wakeup when usart is suspended,
and disable mctrl_gpios wake_irq if device_may_wakeup when usart is
resumed.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20220203171644.12231-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new API to enable / disable wake_irq in order to enable gpio irqs as
wakeup irqs for the uart port.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20220203171644.12231-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The free_page(addr), which becomes free_pages(addr, 0) checks addr
against 0. No need to repeat this check in the callers.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220204152808.10808-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_MAGIC_MULTIPLIER is userspace available bit and can be changed
at any time. There is no sense to rely on it to be always present.
This reverts commit b4ccaf5aa2.
Note, that code was not reliably worked before, hence it implies
no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: b4ccaf5aa2 ("serial: 8250_pericom: Re-enable higher baud rates")
Link: https://lore.kernel.org/r/20220203150026.19087-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the similar way how it's done in 8250_pericom, derive the number of
the UART ports from PCI ID for Acces I/O cards.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220127180608.71509-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_circ_empty() instead of open-coding it via xmit->head & tail.
Use preexisting mcf_stop_tx() to avoid stop-tx code duplication.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linflex_txint() calls linflex_transmit_buffer() which calls
uart_write_wakeup(). So there is no point to repeat it in
linflex_txint() again -- remove it.
Cc: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new linflex_put_char() helper to send a character. And use
it on both places this code was duplicated.
Cc: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_uart_port::rx_ring is defined as struct circ_buf, but circ_buf.h
is not included explicitly in atmel_serial.c. It is included only
implicitly via serial_core.h. Fix this as serial_core.h might not
include that header in the future.
Signed-off-by:Jiri Slaby <jslaby@suse.cz>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20220124071430.14907-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some EXPORT_SYMBOLs are grouped at one location. Some follow functions
they export, but a newline is present before them. Fix all these and
move them where they belong.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for counting the tty buffer overruns in fsl_lpuart driver
like other uart drivers.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220111085130.5817-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Triggering RX interrupt for every byte defeats the purpose of aging
timer and leads to interrupt storm at high baud rates. The interrupt
storm can starve line discipline worker and prevent tty throttling,
rendering hardware/software flow control useless.
Increase receiver trigger level to 8 to increase the minimum period
between RX interrupts to 8 characters time. The tradeoff is increased
latency.
Aging timer resets with every received character. Worst case scenario
happens when RX data intercharacter delay is slightly less than the
aging timer timeout (8 characters time). The upper bound of the time
a character can wait in RxFIFO before interrupt is raised is:
(RXTL - 1) * (8 character time timeout + received 1 character time)
Usually the data is received in frames, with low intercharacter delay.
In such case the latency increase is 8 characters time at the end of
the frame with probability (RXTL - 1) / RXTL.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220117060417.624613-1-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220114085156.43041-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTS polarity of rs485-enabled ports is currently initialized on uart
open via:
tty_port_open()
tty_port_block_til_ready()
tty_port_raise_dtr_rts() # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts()
There's at least three problems here:
First, if no baud rate is set, RTS polarity is not initialized.
That's the right thing to do for rs232, but not for rs485, which
requires that RTS is deasserted unconditionally.
Second, if the DeviceTree property "linux,rs485-enabled-at-boot-time" is
present, RTS should be deasserted as early as possible, i.e. on probe.
Otherwise it may remain asserted until first open.
Third, even though RTS is deasserted on open and close, it may
subsequently be asserted by uart_throttle(), uart_unthrottle() or
uart_set_termios() because those functions aren't rs485-aware.
(Only uart_tiocmset() is.)
To address these issues, move RTS initialization from uart_port_dtr_rts()
to uart_configure_port(). Prevent subsequent modification of RTS
polarity by moving the existing rs485 check from uart_tiocmget() to
uart_update_mctrl().
That way, RTS is initialized on probe and then remains unmodified unless
the uart transmits data. If rs485 is enabled at runtime (instead of at
boot) through a TIOCSRS485 ioctl(), RTS is initialized by the uart
driver's ->rs485_config() callback and then likewise remains unmodified.
The PL011 driver initializes RTS on uart open and prevents subsequent
modification in its ->set_mctrl() callback. That code is obsoleted by
the present commit, so drop it.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2d2acaf3a69e89b7bf687c912022b11fd29dfa1e.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.
Fix start_tx condition to allow x_char to be sent.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cf ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5021d709b3.
The patch is still a bit buggy, and this breaks some other hardware
types. It needs to be resubmitted in a non-buggy way, and make sure the
other hardware types also continue to work properly.
Fixes: 5021d709b3 ("tty: serial: Use fifo in 8250 console driver")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/Ye/1+Z8mEzbKbrqG@linutronix.de
Link: https://lore.kernel.org/r/a1ac6254-f79e-d131-fa2a-c7ad714c6d4a@nvidia.com
Cc: Wander Lairson Costa <wander@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----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=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this error handling, "transmit_chars_dma" function will call
"transmit_chars_pio" once per characters. But "transmit_chars_pio" will
continue to send characters while xmit buffer is not empty.
Remove this useless loop, one call is sufficient.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If flow control is enabled, framework will call stop_tx to
pause transfer and then call start_tx to resume transfer.
Clear USART_CR3_DMAT bit in stop_tx ops to pause DMA transfer.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX DMA state condition is handled by tx_dma_busy boolean.
This boolean is set when dma descriptor is requested and reset when dma
channel is stopped (dma_terminate).
In stm32_usart_serial_remove(), stm32_usart_stop_tx() and
stm32_usart_transmit_chars_dma() fallback error case, DMA channel is
stopped but tx_dma_busy is not handled.
Rework the driver by using two new functions to solve this issue:
- stm32_usart_tx_dma_started return true if DMA TX have a descriptor.
- stm32_usart_tx_dma_enabled return true if DMAT bit is set.
stm32_usart_tx_dma_started uses tx_dma_busy flag to prevent dual DMA
transaction at the same time. This flag is set when a DMA transaction
begins and is unset when dmaengine_terminate_async function is called.
A new DMA transaction cannot be created if this flag is set.
Create a new function "stm32_usart_tx_dma_terminate" to be sure the flag
is unset after each call of dmaengine_terminate_async.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminate DMA transaction and clear CR3_DMAT when shutdown is requested,
instead of when remove is requested. If DMA transfer is not stopped in
shutdown ops, driver will fail to start a new DMA transfer after next
startup ops.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8d8ffa477 ("amba-pl011: do not disable RTS during shutdown")
amended the PL011 serial driver to leave DTR/RTS polarity untouched on
tty close. That change made sense.
But the commit also added code to save DTR/RTS state to an internal
variable on tty close and restore it on tty open. That part of the
commit makes less sense: The driver has no ->pm() callback, so the uart
remains powered after tty close and automatically preserves register
state, including DTR/RTS.
Saving and restoring registers isn't the job of the ->startup() and
->shutdown() callbacks anyway. Rather, it should happen in ->pm().
Additionally, after pl011_startup() restores the state, the serial core
overrides it in uart_port_dtr_rts() if a baud rate has been set:
tty_port_open()
uart_port_activate()
uart_startup()
uart_port_startup()
pl011_startup() # restores DTR/RTS from uap->old_cr
tty_port_block_til_ready()
tty_port_raise_dtr_rts # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts() # raises DTR/RTS
The serial core also overrides DTR/RTS on tty close in uart_shutdown()
if C_HUPCL(tty) is set. So a user-defined DTR/RTS polarity won't
survive a close/open cycle anyway, unless the user has set the baud rate
to zero and disabled hupcl on the tty.
Bottom line is, the code to save and restore DTR/RTS has no effect.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/e22089ab49e6e78822c50c8c4db46bf3ee885623.1641129328.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_set_termios() briefly resets the CR register to zero, thereby
glitching DTR/RTS signals. With rs485 this may result in the bus being
occupied for no reason.
Where does this register write originate from?
The PL011 driver was forked from the PL010 driver in 2004:
https://git.kernel.org/history/history/c/157c0342e591
Until this commit, the PL010 driver's IRQ handler ambauart_int()
modified the CR register without holding the port spinlock.
ambauart_set_termios() also modified that register. To prevent
concurrent read-modify-writes by the IRQ handler and to prevent
transmission while changing baudrate, ambauart_set_termios() had to
disable interrupts. On the PL010, that is achieved by writing zero to
the CR register.
However, on the PL011, interrupts are disabled in the IMSC register,
not in the CR register.
Additionally, the commit amended both the PL010 and PL011 driver to
acquire the port spinlock in the IRQ handler, obviating the need to
disable interrupts in ->set_termios().
So the CR register write is obsolete for two reasons. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/f49f945375f5ccb979893c49f1129f51651ac738.1641129062.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All mainline .dts files have been using the stable UART since Linux
4.16. Drop the legacy compatible strings and related clock code.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20211230102110.3861-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of failures brcmuart_probe() always returned -ENODEV, this
isn't correct for example platform_get_irq_byname() may return
-EPROBE_DEFER to handle such cases propagate error codes in
brcmuart_probe() in case of failures.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns signed status. It should be stored and
compared as signed value before storing to unsigned variable. Implicit
conversion from signed to unsigned and then comparison with less than
zero is wrong as unsigned value can never be less than zero.
Fixes: f087f01ca2 ("serial: lantiq: Use platform_get_irq() to get the interrupt")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/YcIf7+oSWWn34ND6@debian-BULLSEYE-live-builder-AMD64
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_8250_port contains mcr_mask and mcr_force members whose
sole purpose is to work around an Alpha-specific quirk. This code
doesn't belong in the core where it is executed by everyone else,
so move it to a proper ->set_mctrl callback which is used on the
affected Alpha machine only.
The quirk was introduced in January 1995:
https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/diff/drivers/char/serial.c?h=1.1.83
The members in struct uart_8250_port were added in 2002:
https://git.kernel.org/history/history/c/4524aad27854
The quirk applies to non-PCI Alphas and arch/alpha/Kconfig specifies
"select FORCE_PCI if !ALPHA_JENSEN". So apparently the only affected
machine is the EISA-based Jensen that Linus was working on back then:
https://lore.kernel.org/all/CAHk-=wj1JWZ3sCrGz16nxEj7=0O+srMg6Ah3iPTDXSPKEws_SA@mail.gmail.com/
Up until now the quirk is not applied unless CONFIG_PCI is disabled.
If users forget to do that or run a generic Alpha kernel, the serial
ports aren't usable on Jensen. Avoid by confining the quirk to
CONFIG_ALPHA_JENSEN instead of !CONFIG_PCI. On generic Alpha kernels,
auto-detect at runtime whether the quirk needs to be applied.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Ulrich Teichert <krypton@ulrich-teichert.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/b83d069cb516549b8a5420e097bb6bdd806f36fc.1640695609.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a6845e1e1b ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b ("serial: core: Consider rs485 settings to drive RTS")
Cc: stable@vger.kernel.org # v4.14+
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note: I am using a small test app + driver located at [0] for the
problem description. serco is a driver whose write function dispatches
to the serial controller. sertest is a user-mode app that writes n bytes
to the serial console using the serco driver.
While investigating a bug in the RHEL kernel, I noticed that the serial
console throughput is way below the configured speed of 115200 bps in
a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but
I got 2.5KB/s.
$ time ./sertest -n 2500 /tmp/serco
real 0m0.997s
user 0m0.000s
sys 0m0.997s
With the help of the function tracer, I then noticed the serial
controller was taking around 410us seconds to dispatch one single byte:
$ trace-cmd record -p function_graph -g serial8250_console_write \
./sertest -n 1 /tmp/serco
$ trace-cmd report
| serial8250_console_write() {
0.384 us | _raw_spin_lock_irqsave();
1.836 us | io_serial_in();
1.667 us | io_serial_out();
| uart_console_write() {
| serial8250_console_putchar() {
| wait_for_xmitr() {
1.870 us | io_serial_in();
2.238 us | }
1.737 us | io_serial_out();
4.318 us | }
4.675 us | }
| wait_for_xmitr() {
1.635 us | io_serial_in();
| __const_udelay() {
1.125 us | delay_tsc();
1.429 us | }
...
...
...
1.683 us | io_serial_in();
| __const_udelay() {
1.248 us | delay_tsc();
1.486 us | }
1.671 us | io_serial_in();
411.342 us | }
In another machine, I measured a throughput of 11.5KB/s, with the serial
controller taking between 80-90us to send each byte. That matches the
expected throughput for a configuration of 115200 bps.
This patch changes the serial8250_console_write to use the 16550 fifo
if available. In my benchmarks I got around 25% improvement in the slow
machine, and no performance penalty in the fast machine.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20211222112831.1968392-2-wander@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the SCIF serial driver to remove printouts for break, frame, parity
and overrun errors. This reduces the amount of console printouts generated
by the defconfig kernel on R-Car Gen3 for certain use cases. To retrieve
more information about such errors the user may inspect counters. Also these
errors are fed into the TTY layer for further application specific handling.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/163884254093.18109.2982470198301927679.sendpatchset@octo
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to stick with standard API to write and read DL value
when the hardware is compatible with it. In case any quirks are
needed it may be easily added in one place rather than modifying
code here and there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UPF_MAGIC_MULTIPLIER to the port flags since there is now
range checking in serial8250_get_baud_rate() in 8250_port.c.
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pericom along with Acces I/O support consumes a lot of LOCs in 8250_pci.c.
For the sake of easier maintenance, split it to a separate driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On modern Exynos SoCs (like Exynos850) the UART can be implemented as a
part of USI IP-core. In such case, USI driver is used to initialize USI
registers, and it also calls of_platform_populate() to instantiate all
sub-nodes (e.g. serial node) of USI node. When serial driver is
built-in, but USI driver is a module, and CONFIG_SERIAL_SAMSUNG_CONSOLE
is enabled, next call chain will happen when loading USI module from
user space:
usi_init
v
usi_probe
v
of_platform_populate
v
s3c24xx_serial_probe
v
uart_add_one_port
v
uart_configure_port
v
register_console
v
try_enable_new_console
v
s3c24xx_serial_console_setup
But because the serial driver is built-in, and
s3c24xx_serial_console_setup() is marked with __init keyword, that
symbol will discarded and long gone by that time already, causing failed
paging request.
That happens during the next config combination:
EXYNOS_USI=m
SERIAL_SAMSUNG=y
SERIAL_SAMSUNG_CONSOLE=y
That config should be completely possible, so rather than limiting
SERIAL_SAMSUNG choice to "m" only when USI=m, remove __init keyword for
all affected functions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-6-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable serial driver to be built as a module. To do so, init the console
support on driver/module load instead of using console_initcall().
Inspired by commit 87a0b9f98a ("tty: serial: meson: enable console as
module").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-5-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USI control is now extracted to the dedicated USI driver. Remove USI
related code from serial driver to avoid conflicts and code duplication.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-4-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmG/rsoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGLW8H/0sfRUxZNJ+DgO6W
0LpyIx1DF7S2x1wOQGl7VZsjdy+dtuOW4BtEoqhuQWgQ2sr0zbavbeyZYTXD1+d6
I1h5C6JMD138JkoqZNdeyWwsalAFtVItH+lzszUGKTxueTbKCJTkGMerBZVu/gVY
U3QYZHEkUH6o/2fINYfSMhEgyJpjVEUoaztB2drsC0tNUGeDjTmrhlRrWIKZ6Kn+
oAiMqsomSBF09TZ++GEqMYDTm39CwNDPJzKGyyOx86ydcg4ErWvjp1jfAUX0cvFG
dso2K5mDzTewdF8bW0A1KvsQaliMFpxgZ5CTblYQ6HvyltjRj+0B8207VzHQXBKV
YFZ8y9A=
=mfug
-----END PGP SIGNATURE-----
Merge 5.16-rc6 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable tmp is being masked with a bitmask and the value is being
written to port base + 0x3c. However, the masked value is being written
back to tmp and tmp is never used after this. The assignmentment is
redundant, replace the &= operator with just &.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewesd-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211205232822.110099-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
continuing to use static IRQ resources is blocking removing the static setup
from the DT core code.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215224832.1985402-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci driver supports up to four input clocks, of which only the
first one is mandatory.
Replace devm_clk_get() and custom error checking by
devm_clk_get_optional(), to simplify the code and to catch all real
errors.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/bce27288cb570952dd96b441e1af8768ad8b4870.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1b463bd510 ("ARM: dts: r8a7794: Rename the serial
port clock to fck") in v4.6, all upstream DTS files call the SCIF
functional clock "fck".
Hence the time is ripe to drop backward-compatibility with old DTBs that
use the old "sci_ick" name.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b4103e44d6ac46b6c1c264e2aeac80b39941fe74.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the preferred platform_get_irq() call to retrieve the interrupts. These
have the advantage of working with deferred probe and gets us one step
closer to removing of_irq_to_resource_table().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215224800.1984391-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.
Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.
Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.
Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20211129174238.8333-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The base address of uartlite registers could be 64 bit address which is from
device resource. When ulite_probe() calls ulite_assign(), this 64 bit
address is casted to 32-bit. The fix is to replace "u32" type with
"phys_addr_t" type for the base address in ulite_assign() argument list.
Fixes: 8fa7b61006 ("[POWERPC] Uartlite: Separate the bus binding from the driver proper")
Signed-off-by: Lizhi Hou <lizhi.hou@xilinx.com>
Link: https://lore.kernel.org/r/20211129202302.1319033-1-lizhi.hou@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use wait_event_interruptible in lpuart_dma_shutdown isn't a reasonable
behavior, since it may cause the system hang here if the condition
!sport->dma_tx_in_progress never to be true in some corner case, such as
when enable the flow control, the dma tx request may never be completed
due to the peer's CTS setting when run .shutdown().
So here change to use wait_event_interruptible_timeout instead of
wait_event_interruptible, the tx dma will be forcibly terminated if the
tx dma request cannot be completed within 300ms.
Considering the worst tx dma case is to have a 4K bytes tx buffer, which
would require about 300ms to complete when the baudrate is 115200.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211203030441.22873-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.
Fixes: 34df42f59a ("serial: at91: add rx dma support")
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211125090028.786832-4-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9b ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear RTSD status before enabling the irq event for RTSD in
imx_uart_enable_wakeup function.
Since RTSD can be set as the wakeup source, this can avoid any risk of
false triggering of a wake-up interrupts.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125014306.4432-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a9c3f68f3c (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
drivers/tty/.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the StarFive JH7100 RISC-V SoC the UART core clocks can't be set to
exactly 16 * 115200Hz and many other common bitrates. Trying this will
only result in a higher input clock, but low enough that the UART's
internal divisor can't come close enough to the baud rate target.
So rather than try to set the input clock it's better to skip the
clk_set_rate call and rely solely on the UART's internal divisor.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211116150119.2171-15-kernel@esmil.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two consequent checks of uport != NULL in
uart_port_shutdown(). Join these two under a single block.
De-multiline the comments when shuffling with them anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 89d4f98ae9 ("ARM: remove zte zx platform") missed to remove some
definitions for this platform's debug and serial, e.g., code dependent on
the config DEBUG_ZTE_ZX.
Fortunately, ./scripts/checkkconfigsymbols.py detects this and warns:
DEBUG_ZTE_ZX
Referencing files: arch/arm/include/debug/pl01x.S
Further review by Arnd Bergmann identified even more dead code in the
amba serial driver.
Remove all this left-over from the zte zx platform.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211102063810.932-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jing Yao <yao.jing2@zte.com.cn>
Link: https://lore.kernel.org/r/20211104114754.30983-1-yao.jing2@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LITEX symbol is neither a build or runtime dependency for the
liteuart serial driver.
LITEX is selected by the "LiteX SoC Controller" driver, which does a
probe-time register-access sanity check and panics if the SoC has not
been configured correctly. That driver's Kconfig entry asserts that any
LiteX driver using the LiteX register accessors should depend on LITEX,
but currently only the serial driver complies.
Relax this LITEX "dependency" in order to make it easier to compile test
the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to release the allocated minor number before returning on
probe errors.
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deregister the port when unbinding the driver to prevent it from being
used after releasing the driver data and leaking memory allocated by
serial core.
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drvdata has to be set in _probe() - otherwise platform_get_drvdata()
causes null pointer dereference BUG in _remove().
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilia Sergachev <silia@ethz.ch>
Link: https://lore.kernel.org/r/20211115224944.23f8c12b@dtkw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 9969394501 ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e4 ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145a ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_CONSOLE_POLL=y, and CONFIG_SERIAL_CPM=m (hence
CONFIG_SERIAL_CPM_CONSOLE=n):
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1109:12: warning: ‘udbg_cpm_getc’ defined but not used [-Wunused-function]
1109 | static int udbg_cpm_getc(void)
| ^~~~~~~~~~~~~
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1095:13: warning: ‘udbg_cpm_putc’ defined but not used [-Wunused-function]
1095 | static void udbg_cpm_putc(char c)
| ^~~~~~~~~~~~~
Fix this by making the udbg definitions depend on
CONFIG_SERIAL_CPM_CONSOLE, in addition to CONFIG_CONSOLE_POLL.
Fixes: a60526097f ("tty: serial: cpm_uart: Add udbg support for enabling xmon")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027075326.3270785-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Data may be stored in DMA RX buffer, when suspending. The data needs
to be pushed to the upper layer. We can't rely on the timeout IRQ (RTOR)
that can't be triggered into low power state. So safely clear DMA request
(DMAR), force the DMA reception routines to push RX buffer content, before
disabling RX DMA. This way, handover to pio mode is safe.
Only call tty_flip_buffer_push() when there is RX data to handle.
Move the locking outside of stm32_usart_receive_chars() to prevent a race
condition, when disabling DMA request upon suspend / pm_runtime_suspend.
Data may be received under IRQ and pushed before
stm32_usart_receive_chars() has pushed older data from DMA rx_buf upon
suspend.
The sequence in suspend routine needs proper locking to avoid this.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA prevents the system to suspend when an UART RX wake-up source is
using DMA. DMA can't suspend while DMA channels are still active.
Terminate DMA transfer at suspend, and restart a new DMA transfer at
resume. Create stm32_usart_start_rx_dma_cyclic function to factorize
dma RX initialization. Move RX DMA code related to wakeup into
stm32_usart_serial_en_wakeup() routine to ease further improvements
on wakeup from low power modes.
Don't enable/disable wakeup on uninitialized port.
There may be data residue in the RX FIFO while suspending. Flush it at
suspend time. Receiver timeout interrupt won't trigger later in low power
mode, so call stm32_usart_receive_chars() in case there's data to handle.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX DMA channel is kept active forever (from the probe). That prevents
going to low power mode when it is used. This change moves the
DMA configuration and enabling procedures to startup routine to allow
transition to low power mode.
The DMA disabling procedure is implemented in stop_rx routine as this
ops has to stop characters reception, and DMA transation in shutdown.
Clean useless dma_async_tx_descriptor initialization to NULL value.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONSOLE_POLL=n, CONFIG_SERIAL_SUNZILOG_CONSOLE=n, and CONFIG_SERIO=m:
drivers/tty/serial/sunzilog.c:1128:13: error: ‘sunzilog_putchar’ defined but not used [-Werror=unused-function]
1128 | static void sunzilog_putchar(struct uart_port *port, int ch)
| ^~~~~~~~~~~~~~~~
Fix this by marking sunzilog_putchar() __maybe_unused.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211026080426.2444756-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'else' keyword is not needed when previous conditional branch returns
to the upper layer. Get rid of redundant 'else' keyword in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop can be refactored by using ARRAY_SIZE() instead of NULL terminator.
This reduces code base and makes it easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was updating the port uartclk before setting the new rate in
an attempt to avoid having the clock notifier redundantly update the
divisors.
The set_termios() callback is however called under the termios semaphore
and tty-port mutex so the worker scheduled by the clock notifier will
block in serial8250_update_uartclk() until the uartclk and divisors have
been updated anyway.
Drop the unnecessary swaps and incorrect comment and simply update the
uartclk field if the clock-rate change was successful.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
