This allows us to pass HE rates down into the stack.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-2-pradeepc@codeaurora.org
In some scenarios like firmware crashes during init time
and hardware gets restarted after qmi firmware ready event.
During restart, ath11k_core_qmi_firmware_ready() returns timeout.
But, this failure is not handled and ATH11K_FLAG_REGISTERED is set.
When hardware restart completed, firmware sends firmware ready event
again. Since ATH11K_FLAG_REGISTERED is already set, ath11k handles
this as core restart. Inits are not done because of previous timeout.
But ath11k_core_restart does deinit's which causes NULL pointer crash.
Fix this by handling failure from ath11k_core_qmi_firmware_ready().
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-00881-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645079195-13564-1-git-send-email-quic_seevalam@quicinc.com
REO2SW ring descriptor is currently allocated in cacheable memory.
While reaping reo ring entries on second trial after updating head
pointer, first entry is not invalidated before accessing it.
This results in host reaping and using cached descriptor which is
already overwritten in memory by DMA device (HW).
Since the contents of descriptor(buffer id, peer info and other information
bits) are outdated host throws errors like below while parsing corresponding
MSDU's and drops them.
[347712.048904] ath11k_pci 0004:01:00.0: msdu_done bit in attention is not set
[349173.355503] ath11k_pci 0004:01:00.0: frame rx with invalid buf_id 962
Move the try_again: label above ath11k_hal_srng_access_begin()
so that first entry will be invalidated and prefetched.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 6452f0a3d5 ("ath11k: allocate dst ring descriptors from cacheable memory")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645000354-32558-1-git-send-email-quic_ramess@quicinc.com
Hardware random number generators are supposed to use the hw_random
framework. This commit turns ath9k's kthread-based design into a proper
hw_random driver.
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Rui Salvaterra <rsalvaterra@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220216113323.53332-1-Jason@zx2c4.com
The rddm_size is needed by firmware while mhi enter RDDM state, add it
to support recovery when ath11k receive MHI_CB_EE_RDDM message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-4-quic_wgong@quicinc.com
This is to fix m3 buffer reuse issue as m3_mem->size isn't set to
ZERO in free function, which leads invalid m3 downloading to
firmware and firmware crashed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-3-quic_wgong@quicinc.com
ath11k_qmi_free_target_mem_chunk() and ath11k_qmi_m3_free() is static
in qmi.c, they are needed for recovery, export them in a new function.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-2-quic_wgong@quicinc.com
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kmalloc(). For example:
struct wcn36xx_hal_ind_msg {
struct list_head list;
size_t msg_len;
u8 msg[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220208015606.1514022-1-chi.minghao@zte.com.cn
More than 20000 PPDU id jumping causing status ring and destination
ring processing not sync. The status ring is processed and the
destination ring is not processed. Since destination is not reaped for
so long, backpressure occurs at the destination ring.
To address this issue update the PPDU id with the latest PPDU, this
will allow the destination ring to be reaped and will prevent the
rings from getting out of sync.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220210064706.6171-1-quic_kathirve@quicinc.com
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-2-git-send-email-quic_vnaralas@quicinc.com
Fix WARN_ON() from ath11k_mac_update_vif_chan() if vdev is not up.
Since change_chanctx can be called even before vdev_up from
ieee80211_start_ap->ieee80211_vif_use_channel->
ieee80211_recalc_radar_chanctx.
Do vdev stop followed by a vdev start in case of vdev is down.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-1-git-send-email-quic_vnaralas@quicinc.com
The rate_idx which passed to ath11k_debugfs_sta_add_tx_stats() by
ath11k_dp_tx_update_txcompl() is not initialized, add initialization
for it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Fixes: 1b8bb94c06 ("ath11k: report tx bitrate for iw wlan station dump")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060816.423-1-quic_wgong@quicinc.com
This code needs "channel" to be initialized to NULL for it to work
correctly.
Fixes: d6f2746691 ("wcn36xx: Track the band and channel we are tuned to")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220201125941.GA22458@kili
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These calls are used for debugging and will be required for WFA
certification tests.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220131031043.1295-1-alokad@codeaurora.org
Add debugfs interface "fw_dbglog_config" to configure firmware log level.
Configuration is done via WMI command WMI_DBGLOG_CFG_CMDID.
Command to configure,
echo "<dbglog_param> <values>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
where dbglog_param can be,
1) WMI_DEBUG_LOG_PARAM_LOG_LEVEL - configure log level for a given module
here, <values> = <0xaaaa00bb>, 'aaaa' - module id and 'bb' - loglevel
2) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE - enable debug log for a given vdev
here, <values> = vdev_id
3) WMI_DEBUG_LOG_PARAM_VDEV_DISABLE - disable debug log for a given vdev
except ERROR logs
here, <values> = vdev_id
4) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE_BITMAP - set vdev enable bitmap
here, <values> = vdev_enable_bitmap
5) WMI_DEBUG_LOG_PARAM_MOD_ENABLE_BITMAP - set a given log level to all the
modules specified in the module bitmap. Command to configure for this log param,
$ echo "5 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
6) WMI_DEBUG_LOG_PARAM_WOW_MOD_ENABLE_BITMAP - Wow mode specific logging enable.
Command to configure for this log param,
$ echo "6 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
Sample command usage,
To enable module WLAN_MODULE_WMI and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "1 0x10001" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
To enable module bit map from 32 to 63 and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "5 0xffffffff00000001 1 1" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1642405103-32302-1-git-send-email-quic_seevalam@quicinc.com
Currently tx_params is being re-assigned with a new value and the
previous setting IEEE80211_HT_MCS_TX_RX_DIFF is being overwritten.
The assignment operator is incorrect, the original intent was to
bit-wise or the value in. Fix this by replacing the = operator
with |= instead.
Kudos to Christian Lamparter for suggesting the correct fix.
Fixes: fe8ee9ad80 ("carl9170: mac80211 glue and command interface")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: <Stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220125004406.344422-1-colin.i.king@gmail.com
The spread of capability between the three WiFi silicon parts wcn36xx
supports is:
wcn3620 - 802.11 a/b/g
wcn3660 - 802.11 a/b/g/n
wcn3680 - 802.11 a/b/g/n/ac
We currently treat wcn3660 as wcn3620 thus limiting it to 2GHz channels.
Fix this regression by ensuring we differentiate between all three parts.
Fixes: 8490987bdb ("wcn36xx: Hook and identify RF_IRIS_WCN3680")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220125004046.4058284-1-bryan.odonoghue@linaro.org
For the NL80211_REGDOM_SET_BY_USER hint from cfg80211, it set the new
alpha2 code to ath11k, then ath11k send WMI_SET_INIT_COUNTRY_CMDID to
firmware for all chips currently. When test with WCN6855/QCA6390 chips,
this WMI CMD leads firmware crash.
For AP based chips(ipq8074/qcn9074), WMI_SET_INIT_COUNTRY_CMDID is used
to send to firmware, for STATION based chips(WCN6855/QCA6390), it need to
use another WMI CMD WMI_SET_CURRENT_COUNTRY_CMDID.
Add flag current_cc_support in hardware parameters, it is used to
distinguish AP/STA platform. After that, the firmware will work
normal and the regulatory feature works well for QCA6390/WCN6855.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220119041355.32014-1-quic_wgong@quicinc.com
When station connect to AP of 6 GHz with 40 MHz bandwidth, the TX is
always stay 20 MHz, it is because the flag WMI_PEER_40MHZ is not set
while peer assoc. Add the flag if remote peer is 40 MHz bandwidth.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Fixes: c3a7d7eb4c ("ath11k: add 6 GHz params in peer assoc command")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220119034211.28622-1-quic_wgong@quicinc.com
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing
field initialization.
In htc_connect_service() svc_meta_len and pad are not initialized. Based
on code it looks like in current skb there is no service data, so simply
initialize svc_meta_len to 0.
htc_issue_send() does not initialize htc_frame_hdr::control array. Based
on firmware code, it will initialize it by itself, so simply zero whole
array to make KMSAN happy
Fail logs:
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 4-7 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 16-17 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115122733.11160-1-paskripkin@gmail.com
Add support for get_survey() reporting. Current channel and noise-floor are
reported, other parameters such as scan, busy, TX and RX time are not
immediately available.
Noise is a useful metric to report, so bring it out now.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115001646.3981501-5-bryan.odonoghue@linaro.org
The BDs for each RX frame contain both the RSSI and SNR for the received
frame. If we track and store this information it can be useful to us in
get_survey() and potentially elsewhere.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115001646.3981501-4-bryan.odonoghue@linaro.org
Track the band and channel we are currently tuned to by way of pointers to
the standard structures that describe them both embedded within the driver.
Tracking of the pair makes it much easier when implementing
ieee80211_ops->get_survey to return quickly captured metrics for the
currently tuned channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115001646.3981501-3-bryan.odonoghue@linaro.org
The wcn36xx BD phy descriptor returns both Received Signal Strength
Information (RSSI) and Signal To Noise Ratio (SNR) with each delivered BD.
The macro to extract this data is a simple-one liner, easily imported from
prima driver. This data will be useful to us when implementing
mac80211-ops->get_survey().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115001646.3981501-2-bryan.odonoghue@linaro.org
QCA6174 card often hangs with the current htt_rx_desc
memory layout in some circumstances, because its firmware
fails to handle length differences.
Therefore we must abstract the htt_rx_desc structure
and operations on it, to allow different wireless cards
to use different, unrelated rx descriptor structures.
Define a base htt_rx_desc structure and htt_rx_desc_v1
for use with the QCA family of ath10k supported cards
and htt_rx_desc_v2 for use with the WCN3990 card.
Define htt_rx_desc_ops which contains the abstract operations
to access the generic htt_rx_desc, give implementations
for each card and update htt_rx.c to use the defined
abstract interface to rx descriptors.
Fixes: e3def6f7dd ("ath10k: Update rx descriptor for WCN3990 target")
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Co-developed-by: Enrico Lumetti <enrico@fracta.dev>
Signed-off-by: Enrico Lumetti <enrico@fracta.dev>
Signed-off-by: Francesco Magliocca <franciman12@gmail.com>
Link: https://lore.kernel.org/ath10k/CAH4F6usFu8-A6k5Z7rU9__iENcSC6Zr-NtRhh_aypR74UvN1uQ@mail.gmail.com/
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211216151823.68878-1-franciman12@gmail.com
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211224192626.15843-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Return value directly instead of taking this in another redundant
variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220112080751.667316-1-chi.minghao@zte.com.cn
There is an issue that WCN6855 tries to connect to an AP using
a hardware rate of 1Mb/s , even though the AP has announced
expected rates as [24, 36, 48, 54] in Probe Response frame.
The reason is that WCN6855 firmware clears hardware rate info
of management frames when vdev starts and uses 1Mb/s as default.
To solve it, reconfigure the rate after vdev is started.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220112025400.2222-1-quic_bqiang@quicinc.com
kmalloc_array()/kcalloc() should be used to avoid potential overflow when
a multiplication is needed to compute the size of the requested memory.
kmalloc_array() can be used here instead of kcalloc() because the array is
fully initialized in the next 'for' loop.
Finally, 'cd->detectors' is defined as 'struct pri_detector **detectors;'.
So 'cd->detectors' and '*cd->detectors' are both some pointer.
So use a more logical 'sizeof(*cd->detectors)'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/0fbcd32a0384ac1f87c5a3549e505e4becc60226.1640624216.git.christophe.jaillet@wanadoo.fr
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211224192626.15843-8-prabhakar.mahadev-lad.rj@bp.renesas.com
The struct ath5k_hw member ah_txq_isr_txok_all is never reset/assigned
outside of ath5k_hw_get_isr() and with the used bitwise-or in the
interrupt handling accumulates all ever set interrupt flags.
Fix this by clearing ah_txq_isr_txok_all before assigning.
Patch tested with Senao NMP-8602 card
Qualcomm Atheros AR5413/AR5414 Wireless Network Adapter [AR5006X(S) 802.11abg] (rev 01)
ath5k: phy6: Atheros AR5413 chip found (MAC: 0xa4, PHY: 0x61)
running IBSS mode against Atheros (ath9k) card using
ping and iperf traffic.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-5-ps.report@gmx.net
Remove unused ah_txq_isr_txurn member from struct ath5k_hw (set in
ath5k_hw_get_isr() but never used anywhere).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-4-ps.report@gmx.net
Remove unused ah_txq_isr_qcborn member from struct ath5k_hw (set in
ath5k_hw_get_isr() but never used anywhere).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-3-ps.report@gmx.net
Remove unused ah_txq_isr_qcburn member from struct ath5k_hw (set in
ath5k_hw_get_isr() but never used anywhere).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-2-ps.report@gmx.net
Remove unused ah_txq_isr_qtrig member from struct ath5k_hw (set in
ath5k_hw_get_isr() but never used anywhere).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-1-ps.report@gmx.net
The "ret" vairable is not set at this point. It could be uninitialized
or zero. The correct thing to return is -ENODEV.
Fixes: 6ac04bdc5e ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111071445.GA11243@kili
Move the function below ath11k_dp_rx_mon_dest_process() and remove
the forward declaration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111032224.14093-2-quic_alokad@quicinc.com
RX PPDU statistics collection is missing when monitor mode co-exists
with other modes. This commit combines the processing of the destination
ring with the status ring to fix the issue.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111032224.14093-1-quic_alokad@quicinc.com
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
The bug was found during fuzzing. Stacktrace locates it in
ath5k_eeprom_convert_pcal_info_5111.
When none of the curve is selected in the loop, idx can go
up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound.
pd = &chinfo[pier].pd_curves[idx];
There are many OOB writes using pd later in the code. So I
added a sanity check for idx. Checks for other loops involving
AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not
used outside the loops.
The patch is NOT tested with real device.
The following is the fuzzing report
BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
Write of size 1 at addr ffff8880174a4d60 by task modprobe/214
CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
__kasan_report.cold+0x37/0x7c
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
kasan_report+0xe/0x20
ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
? apic_timer_interrupt+0xa/0x20
? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k]
ath5k_eeprom_init+0x2513/0x6290 [ath5k]
? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
? usleep_range+0xb8/0x100
? apic_timer_interrupt+0xa/0x20
? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k]
ath5k_hw_init+0xb60/0x1970 [ath5k]
ath5k_init_ah+0x6fe/0x2530 [ath5k]
? kasprintf+0xa6/0xe0
? ath5k_stop+0x140/0x140 [ath5k]
? _dev_notice+0xf6/0xf6
? apic_timer_interrupt+0xa/0x20
ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k]
? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
? mutex_lock+0x89/0xd0
? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
? pci_device_remove+0x280/0x280
? pci_device_remove+0x280/0x280
really_probe+0x209/0x5d0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YckvDdj3mtCkDRIt@a-10-27-26-18.dynapool.vpn.nyu.edu
LDPC is one the FEC type advertised in msdu_start info2 for HT packet
type. Hence, add hardware specific callback for fetching LDPC
support from msdu start and enable RX_ENC_FLAG_LDPC flag while passing
rx status to mac80211.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638294648-844-3-git-send-email-quic_ppranees@quicinc.com
When there is an error in peer create process from
ath11k_peer_find(), the code attempts to handle a fallback
for peer create. When this fallback fails, the driver returns
the fallback return code rather than actual error code
(-ENOENT). So refactor the fallback routine to return
the actual error code.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640244819-21183-1-git-send-email-quic_periyasa@quicinc.com
Currently, ath11k_core_alloc() creates a single thread workqueue.
This workqueue is not detroyed during clean up when ath11k modules
are unloaded from the kernel and is left as it is.
If workqueue is not destroyed, it could lead to kernel
memory scarcity in a longer run. This could affect self and
other drivers workability as well.
Add destroy workqueue in ath11k_core_free().
Tested on: IPQ8074 WLAN.HK.2.4.0.1-01746-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640231787-17408-1-git-send-email-quic_adisi@quicinc.com
In function ath10k_wow_convert_8023_to_80211(), it will do memcpy for
the new->pattern, and currently the new->pattern and new->mask is same
with the old, then the memcpy of new->pattern will also overwrite the
old->pattern, because the header format of new->pattern is 802.11,
its length is larger than the old->pattern which is 802.3. Then the
operation of "Copy frame body" will copy a mistake value because the
body memory has been overwrite when memcpy the new->pattern.
Assign another empty value to new_pattern to avoid the overwrite issue.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Fixes: fa3440fa2f ("ath10k: convert wow pattern from 802.3 to 802.11")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222031347.25463-1-quic_wgong@quicinc.com
The node pointer is returned by of_find_node_by_type()
or of_parse_phandle() with refcount incremented. Calling
of_node_put() to aovid the refcount leak.
Fixes: 6ac04bdc5e ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211221114003.335557-1-yangyingliang@huawei.com
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmHEgv4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt7jQf/W1J8lkaMw6mYnr+inmwKaP11VIk765Sf
4FXZl4xks5rs5zJOs61c/zInNIbu7QVsJzQLmM/bhTB1zoZMRo6ugXXrZ/LPMT1u
X0mul1rC+NLZLlgaimNXRZUXJ2tGUsYYhGoZLHbcILx7XF7/9WtE4h7tLviLdMYk
l42yjjP6s/I/zQHrLQdA9/puGl7g8CItbwaNZg6+PjgbS9NPGATrw9UZdOWjPcl4
JLMRHVgKtdlYL/U/IvsYg6o3Vbo0r+KEI2IMg5fOSpNwqbeQRIN4cZG4TDeRDqD/
k4/ZiFYlNdfVeWmZxHyqX6D3sroIquKglyah34fjzsJ2TbJC1zMvjw==
=VHFz
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are seeing below error on QCA6390:
...
[70211.671189] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70212.696154] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70213.092941] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
...
The reason is that, with commit 734223d784 ("ath11k: change return
buffer manager for QCA6390"), ath11k expects the return buffer manager
(RBM) field of descriptor configured as HAL_RX_BUF_RBM_SW1_BM when
parsing error frames from WBM2SW3_RELEASE ring. This is a wrong change
cause the RBM field is set as HAL_RX_BUF_RBM_SW3_BM.
The same issue also applies to REO2TCL ring though we have not got any
error reported.
Fix it by changing RBM from HAL_RX_BUF_RBM_SW1_BM to HAL_RX_BUF_RBM_SW3_BM
for these two rings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 734223d784 ("ath11k: change return buffer manager for QCA6390")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222013536.582527-1-quic_bqiang@quicinc.com
Host enables WMI firmware logging feature via QMI message.
Host receives firmware logging messages on WMI_DIAG_EVENTID, then
sends logging messages to user space via event tracing infrastructure.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Cheng Wang <quic_chengwan@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220121053.357087-1-quic_chengwan@quicinc.com
Similar to the same bug in ath10k, a napi disable w/out it being enabled
will hang forever. I believe I saw this while trying rmmod after driver
had some failure on startup. Fix it by keeping state on whether napi is
enabled or not.
And, remove un-used napi pointer in ath11k driver base struct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200903195254.29379-1-greearb@candelatech.com
The strlcpy should not be used because it doesn't limit the source
length. So that it will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, replace strlcpy with strscpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211221070931.725720-1-wangborong@cdjrlc.com
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The regdomain is self-managed type for ath11k, the regdomain info is
reported from firmware, it is not from wireless regdb. Firmware fetch
the regdomain info from board data file before. Currently most of the
regdomain info has moved to another file regdb.bin from board data
file for some chips such as QCA6390 and WCN6855, so the regdomain info
left in board data file is not enough to support the feature which need
more regdomain info.
After download regdb.bin, firmware will fetch the regdomain info from
regdb.bin instead of board data file and report to ath11k. If it does
not have the file regdb.bin, it also can initialize wlan success and
firmware then fetch regdomain info from board data file.
Add download the regdb.bin before download board data for some specific
chip which support supports_regdb in hardware parameters.
download regdb.bin log:
[430082.334162] ath11k_pci 0000:05:00.0: chip_id 0x2 chip_family 0xb board_id 0x106 soc_id 0x400c0200
[430082.334169] ath11k_pci 0000:05:00.0: fw_version 0x110c8b4c fw_build_timestamp 2021-10-25 07:41 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02892-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
[430082.334414] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/regdb.bin size 24310
output of "iw reg get"
global
country US: DFS-FCC
(2402 - 2472 @ 40), (N/A, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
(5735 - 5835 @ 80), (N/A, 30), (N/A)
(57240 - 63720 @ 2160), (N/A, 40), (N/A)
phy#0 (self-managed)
country US: DFS-FCC
(2402 - 2472 @ 40), (6, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 24), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 24), (0 ms), DFS, AUTO-BW
(5735 - 5895 @ 160), (N/A, 30), (N/A), AUTO-BW
(5945 - 7125 @ 160), (N/A, 24), (N/A), NO-OUTDOOR, AUTO-BW
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220062355.17021-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath11k will check the capability, and if it is enabled then
ath11k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath11k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware and also notifies cfg80211.
This only enable rfkill feature for QCA6390, rfkill_pin is all initialized to 0
for other chips in ath11k_hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217102334.14907-1-quic_wgong@quicinc.com
HTT_T2H_MSG_TYPE_PPDU_STATS_IND is a message which include the ppdu
info, currently it is not report from firmware for ath11k, then the
tx bitrate of "iw wlan0 station dump" always show an invalid value
"tx bitrate: 6.0 MBit/s".
To address the issue, this is to parse the info of tx complete report
from firmware and indicate the tx rate to mac80211.
After that, "iw wlan0 station dump" show the correct tx bit rate such
as:
tx bitrate: 78.0 MBit/s MCS 12
tx bitrate: 144.4 MBit/s VHT-MCS 7 short GI VHT-NSS 2
tx bitrate: 286.7 MBit/s HE-MCS 11 HE-NSS 2 HE-GI 0 HE-DCM 0
tx bitrate: 1921.5 MBit/s 160MHz HE-MCS 9 HE-NSS 2 HE-GI 0 HE-DCM 0
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217093722.5739-1-quic_wgong@quicinc.com
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 5.6.0 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
__kasan_report.cold+0x37/0x7c
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? hif_usb_mgmt_cb+0x2d9/0x2d9 [ath9k_htc]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __usb_unanchor_urb+0x12f/0x210
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YXsidrRuK6zBJicZ@10-18-43-117.dynapool.wireless.nyu.edu
syzbot is reporting lockdep warning at ath9k_wmi_event_tasklet() followed
by kernel panic at get_htc_epid_queue() from ath9k_htc_tx_get_packet() from
ath9k_htc_txstatus() [1], for ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID)
depends on spin_lock_init() from ath9k_init_priv() being already completed.
Since ath9k_wmi_event_tasklet() is set by ath9k_init_wmi() from
ath9k_htc_probe_device(), it is possible that ath9k_wmi_event_tasklet() is
called via tasklet interrupt before spin_lock_init() from ath9k_init_priv()
from ath9k_init_device() from ath9k_htc_probe_device() is called.
Let's hold ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID) no-op until
ath9k_tx_init() completes.
Link: https://syzkaller.appspot.com/bug?extid=31d54c60c5b254d6f75b [1]
Reported-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/77b76ac8-2bee-6444-d26c-8c30858b8daa@i-love.sakura.ne.jp
syzbot is reporting lockdep warning followed by kernel panic at
ath9k_htc_rxep() [1], for ath9k_htc_rxep() depends on ath9k_rx_init()
being already completed.
Since ath9k_htc_rxep() is set by ath9k_htc_connect_svc(WMI_BEACON_SVC)
from ath9k_init_htc_services(), it is possible that ath9k_htc_rxep() is
called via timer interrupt before ath9k_rx_init() from ath9k_init_device()
is called.
Since we can't call ath9k_init_device() before ath9k_init_htc_services(),
let's hold ath9k_htc_rxep() no-op until ath9k_rx_init() completes.
Link: https://syzkaller.appspot.com/bug?extid=4d2d56175b934b9a7bf9 [1]
Reported-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/2b88f416-b2cb-7a18-d688-951e6dc3fe92@i-love.sakura.ne.jp
IEEE80211_HW_USES_RSS is set in ath11k, then the device uses RSS and
thus requires parallel RX which implies using per-CPU station statistics
in sta_get_last_rx_stats() of mac80211. Currently signal is only set in
ath11k_mgmt_rx_event(), and not set for RX data packet, then it show
signal as 0 for iw command easily.
Change to get signal from firmware and report to mac80211.
For QCA6390 and WCN6855, the rssi value is already in dbm unit, so
don't need to convert it again.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211216070535.31732-1-quic_wgong@quicinc.com
Switching from legacy usage of ieee80211_get_tx_rates() lookup to direct
rate table lookup in struct ieee80211_sta->rates.
The current rate control API allows drivers to directly get rates from
ieee80211_sta->rates. ath5k is currently one of the legacy drivers that
perform translation/merge with the internal rate table via
ieee80211_get_tx_rates provided by rate control API.
For our upcoming changes to rate control API and the implementation of
transmit power control, this patch changes the behaviour. The call to
ieee80211_get_tx_rates and subsequent calls are also avoided. ath5k now
directly reads rates from sta->rates into its internal rate table. Cause
ath5k does not rely on the rate array in SKB->CB, this is not considered
anymore except for the first entry (used for probing).
Tested this on a PCEngines ALIX with CMP9-GP miniPCI wifi card (Atheros
AR5213A). Generated traffic between AP and multiple STAs before and
after applying the patch and simultaneously measured throughput and
captured rc_stats. Comparison resulted in same rate selection and no
performance loss between both runs.
Co-developed-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211215215042.637-1-jelonek.jonas@gmail.com
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmG8i3cRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZumyAf7BlhO1TUuwhhs9y6fi6KLa/pEOmkx2SRf
9AuEfxxrLPhlzh29Dz4Bn8B+KBG6HFQ1FngSwIAVjLL5pX/1ARBMx9B2TDf9p/Sb
UgkE6WOX29s7LXuC2lDnBnvnKbf5/rdLmZPZCFCv/iKaGAJAYYXYSQjtj5/Fmdkc
PhQNgALWG9a02bfSLk1MlF1lCqt0hsKFQkza29jTa9CKcWYZFK3sTl1spbHAN5yQ
YJMecy+fSxCSuJPZB3elG5os69sz3WGoFY/AYCWoUODNZo18Z4kiAXwurPDIM+GW
3e/lzXe29V1TB36haNe9/C5F2uwoYWGSoWwHcZ62lLpNhJ649wJDbw==
=4wFO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The prima driver facilitates the direct programming of beacon filter tables via
SMD commands.
The purpose of beacon filters is quote:
/* When beacon filtering is enabled, firmware will
* analyze the selected beacons received during BMPS,
* and monitor any changes in the IEs as listed below.
* The format of the table is:
* - EID
* - Check for IE presence
* - Byte offset
* - Byte value
* - Bit Mask
* - Byte reference
*/
The default filter table looks something like this:
tBeaconFilterIe gaBcnFilterTable[12] =
{
{ WLAN_EID_DS_PARAMS, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_ERP_INFO, 0u, { 0u, 0u, 248u, 0u } },
{ WLAN_EID_EDCA_PARAM_SET, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_QOS_CAPA, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_CHANNEL_SWITCH, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_QUIET, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 1u, 0u, 248u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 2u, 0u, 235u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 5u, 0u, 253u, 0u } },
{ WLAN_EID_PWR_CONSTRAINT, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_OPMODE_NOTIF, 0u, { 0u, 0u, 0u, 0u } }
};
Add in an equivalent filter set as present in the prima Linux driver.
For now omit the beacon filter "rem" command as the driver does not have an
explicit call to that SMD command. The filter mask should only count when
we are inside BMPS anyway.
Replicating the ability to program the filter table gives us scope to add and
remove elements in future. For now though this patch makes the rote-copy of the
downstream Linux beacon filter table, which we can tweak as desired from now
on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-4-bryan.odonoghue@linaro.org
The comment in the header with respect to beacon filtering makes a
reference to "the structure above" and "the structure below" which would be
informative if the comment appeared in the right place but, it does not.
Fix the comment location so that it a least makes sense w/r/t the physical
location statements.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-3-bryan.odonoghue@linaro.org
The beacon filter structures need to be packed. Right now its fine because
we don't yet use these structures so just pack them without marking it for
backporting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-2-bryan.odonoghue@linaro.org
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2)
is reserved through DT entries for firmware usage. Send the base
address from DT entries.
If DT entry is available, PCI device will work with
fixed_mem_region else host allocates multiple segments.
IPQ8074 on HK10 board supports multiple PCI devices.
IPQ8074 + QCN9074 is tested with this patch.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638789319-2950-2-git-send-email-akolli@codeaurora.org
In mode-2 QCN9074 firmware uses 15MB of host memory and firmware
request 1MB size segements in QMI, whereas in mode-0 firmware
uses 45MB of host memory and each segment is of 2MB size.
In mode-2 firmware operates with reduced number of vdevs and peers.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-3-kvalo@kernel.org
The next patch changes TARGET_NUM_VDEVS to be dynamic and need access to ab.
Add ab separately to keep the next patch simple.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-2-kvalo@kernel.org
In ath11k_mac_op_hw_scan(), the return value of kzalloc() is directly
used in memcpy(), which may lead to a NULL pointer dereference on
failure of kzalloc().
Fix this bug by adding a check of arg.extraie.ptr.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_ATH11K=m show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202155348.71315-1-zhou1615@umn.edu
Set DTIM policy to DTIM stick mode, so station follows AP DTIM
interval rather than listen interval which is set in peer assoc cmd.
DTIM stick mode is more preferred per firmware team request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948694-15582-1-git-send-email-quic_cjhuang@quicinc.com
The driver reports NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR capability
to upper layer based on the service bit firmware reported. Driver
sets the spoofed flag in scan_ctrl_flag to firmware if upper layer
has enabled this feature in scan request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948007-9609-1-git-send-email-quic_cjhuang@quicinc.com
I updated to sparse v0.6.4 and it warns:
drivers/net/wireless/ath/ath10k/wmi.c: note: in included file (through drivers/net/wireless/ath/ath10k/core.h):
drivers/net/wireless/ath/ath10k/wmi.h:3481:34: warning: array of flexible structures
Fix it by changing the type to u8 array, in struct wmi_phyerr_hdr_arg it's
stored as a void pointer anyway.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209091545.6098-2-kvalo@kernel.org
I updated to sparse v0.6.4 and it warns:
drivers/net/wireless/ath/ath10k/hw.c: note: in included file (through drivers/net/wireless/ath/ath10k/core.h):
drivers/net/wireless/ath/ath10k/htt.h:1503:41: warning: array of flexible structures
drivers/net/wireless/ath/ath10k/htt_rx.c: note: in included file (through drivers/net/wireless/ath/ath10k/core.h):
drivers/net/wireless/ath/ath10k/htt.h:1503:41: warning: array of flexible structures
The structure is unused in ath10k so let's just remove it.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209091545.6098-1-kvalo@kernel.org
For whatever reason, some devices like QCA6390, WCN6855 using ath11k
are not in M3 state during PM resume, but still functional. The
mhi_pm_resume should then not fail in those cases, and let the higher
level device specific stack continue resuming process.
Add an API mhi_pm_resume_force(), to force resuming irrespective of the
current MHI state. This fixes a regression with non functional ath11k WiFi
after suspend/resume cycle on some machines.
Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=214179
Link: https://lore.kernel.org/regressions/871r5p0x2u.fsf@codeaurora.org/
Fixes: 020d3b26c0 ("bus: mhi: Early MHI resume failure in non M3 state")
Cc: stable@vger.kernel.org #5.13
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Reported-by: Pengyu Ma <mapengyu@gmail.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[mani: Switched to API, added bug report, reported-by tags and CCed stable]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211209131633.4168-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unnamed struct sucks and is in the way of further cleanups. Stick the
PCI related MSI data into a real data structure and cleanup all users.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211206210224.374863119@linutronix.de
When scan request on channel 1, it also receive beacon from other
channels, and the beacon also indicate to mac80211 and wpa_supplicant,
and then the bss info appears in radio measurement report of radio
measurement sent from wpa_supplicant, thus lead RRM case fail.
This is to drop the beacon and probe response which is not the same
channel of scanning.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211208061752.16564-1-quic_wgong@quicinc.com
Currently there is no validation on the spectral/CFR report
over the db ring buffers from the hardware. Improper/incomplete
DMA by the target can result in invalid data received by host.
Due to this we may populate incorrect data to user space.
This buffer validation support fix this issues by filling some
magic value in the buffer during buffer replenish and check for
the magic value in the buffer received by the target. If host
detect magic value in the received buffer it will drop the buffer.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1637312901-10279-2-git-send-email-quic_vnaralas@quicinc.com
In full monitor mode, monitor destination ring is read before monitor
status ring. mon_dst_ring has ppdu id, reap till the end of PPDU. Add
all the MPDUs to list. Start processing the status ring, if PPDU id in
status ring is lagging behind, reap the status ring, once the PPDU ID
matches, deliver the MSDU to upper layer. If status PPDU id leading,
reap the mon_dst_ring.
The advantage with full monitor mode is hardware has status buffers
available for all the MPDUs in mon_dst_ring, which makes it possible
to deliver more frames to be seen on sniffer.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-4-git-send-email-akolli@codeaurora.org
In full monitor mode, monitor destination ring is read in
software monitor ring descriptor format instead of
reo_entrance_ring format. Add new sw_mon_ring descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-3-git-send-email-akolli@codeaurora.org
A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207063538.2767954-1-keescook@chromium.org
Currently mac80211 will send 3 scan request for each scan of WCN6855,
they are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN6855 will
cache the RNR IE(Reduced Neighbor Report element) which exist in the
beacon of 2.4 GHz/5 GHz of the AP which is co-located with 6 GHz,
and then use the cache to scan in 6 GHz band scan if the 6 GHz scan
is in the same scan with the 2.4 GHz/5 GHz band, this will helpful to
search more AP of 6 GHz. Also it will decrease the time cost of scan
because firmware will use dual-band scan for the 2.4 GHz/5 GHz, it
means the 2.4 GHz and 5 GHz scans are doing simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN6855 since
it supports 2.4 GHz/5 GHz/6 GHz and it is single pdev which means
all the 2.4 GHz/5 GHz/6 GHz exist in the same wiphy/ieee80211_hw.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129101309.2931-1-quic_wgong@quicinc.com
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
South Korea manufacturer, Samsung, has extended South Korea
regulatory domain pair with 0x5F and has used it for their
devices such as Samsung Galaxy book. Hence add support
0x5F as a regulatory domain pair along with extended country
code, 413.
Signed-off-by: Peter Oh <ebmajor.dev@gmail.com>
Signed-off-by: Andreas Tepe <andreas.tepe@debitel.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210915185611.6195-1-ebmajor.dev@gmail.com
In ath11k, tx of management packet is doing in a work queue. Sometimes
the workqueue does not finish tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.
ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath11k, its purpose is make sure the
deauth was actually sent, so it need to change ath11k to match the
purpose of mac80211.
To address these issue wait for tx mgmt as well as tx data packets.
dmesg log of connect/disconnect to AP:
[ 307.522226] wls1: authenticate with 62:66:e4:e9:6a:a9
[ 307.586565] wls1: send auth to 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.586581] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.586922] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.590179] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.590181] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.598699] wls1: authenticated
[ 307.599483] wls1: associate with 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.599506] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.599519] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.603059] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.603063] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.637105] wls1: associated
[ 317.365239] wls1: deauthenticating from 62:66:e4:e9:6a:a9 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 317.368104] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 317.372622] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 317.378320] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 317.378330] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 317.378359] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421066] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421427] ath11k_pci 0000:05:00.0: mac remove interface (vdev 0)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202063705.14321-1-quic_wgong@quicinc.com
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid some
open-coded arithmetic in allocator arguments.
Note, that this 'bitmap_zalloc()' divides by BITS_PER_LONG the amount of
memory allocated.
The 'roundup()' used to computed the number of needed long should have
been a DIV_ROUND_UP.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Use 'bitmap_zero()' to avoid hand writing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1fe18fb73f71d855043c40c83865ad539f326478.1638396221.git.christophe.jaillet@wanadoo.fr
Kernel test robot reported:drivers/net/wireless/ath/wcn36xx/smd.c:943:33:
sparse: sparse: cast truncates bits from constant value (780 becomes 80)
The 'channels' field is not a simple u8 array but an array of
channel_params. Using sizeof for retrieving the max number of
channels is then wrong.
In practice, it was not an issue, because the sizeof returned
value is 780, which is truncated in min_t (u8) to 80, which is
the value we expect...
Fix that properly using ARRAY_SIZE instead of sizeof.
Fixes: d707f812bb ("wcn36xx: Channel list update before hardware scan")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638435732-14657-1-git-send-email-loic.poulain@linaro.org
Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.
After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware which
is used for QCA6390 and WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-3-quic_wgong@quicinc.com
Currently there are about 60 channels for 6 GHz, then the size of
chan_list in struct scan_req_params which is 40 is not enough to
fill all the channel list of 6 GHz.
Use dynamic memory to save the channel list of scan.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129110939.15711-1-quic_wgong@quicinc.com
bdf_type for caldata in QMI_WLANFW_BDF_DOWNLOAD_REQ_V01 is wrongly
sent as 1. But, expected bdf_type value for caldata and EEPROM is 2 and 3
respectively. It leads to firmware crash. Fix ath11k_qmi_file_type enum
values.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Fixes: 336e7b53c8 ("ath11k: clean up BDF download functions")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638182754-18408-1-git-send-email-quic_seevalam@quicinc.com
Ath11k fails to probe WCN6855 hw2.1 chip:
[ 6.983821] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[ 6.983841] ath11k_pci 0000:06:00.0: Unsupported WCN6855 SOC hardware version: 18 17
This is caused by the wrong bit mask setting of hardware major version:
for QCA6390/QCN6855, it should be BIT8-11, not BIT8-16, so change the
definition to GENMASK(11, 8).
Also, add a separate entry for WCN6855 hw2.1 in ath11k_hw_params.
Please note that currently WCN6855 hw2.1 shares the same firmwares
as hw2.0, so users of this chip need to create a symlink as below:
ln -s hw2.0 hw2.1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 18ac1665e7 ("ath11k: pci: check TCSR_SOC_HW_VERSION")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129025613.21594-1-quic_bqiang@quicinc.com
This patch changes mac80211 rate control for the ath9k driver. The rate lookup
per packet is changed from legacy usage of ieee80211_get_tx_rates() to the new
rate table based lookup in struct ieee80211_sta->rates.
The most recent rate control API, introduced with commit 0d528d85c5
("mac80211: improve the rate control API"), allows drivers to directly get
rates from ieee80211_sta->rates. This is not used by every driver yet, the
translation/merge is currently performed in ieee80211_get_tx_rates. This patch
changes the behaviour and avoids the call to ieee80211_get_tx_rates and
subsequent calls. ath9k now directly reads rates from sta->rates into its rate
table. Cause ath9k does not expect rate selection in SKB->CB, the table merge
does not consider rate array in SKB->CB except for the first entry (used for
probing).
Tested with a 8devices Rambutan with QCA9558 SoC by performing two runs, one
without the patch and one with. Generated traffic between AP and multiple STAs
in each run, measured throughput and captured rc_stats. Comparison of both
runs resulted in same rate selection and no performance loss or other negative
effects.
Co-developed-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211128090753.958-1-jelonek.jonas@gmail.com
On an imx6dl-pico-pi board with a QCA9377 SDIO chip, simply trying to
connect via ssh to another machine causes:
[ 55.824159] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.832169] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.838529] ath10k_sdio mmc1:0001:1: failed to push frame: -12
[ 55.905863] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.913650] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.919887] ath10k_sdio mmc1:0001:1: failed to push frame: -12
, leading to an ssh connection failure.
One user inspected the size of frames on Wireshark and reported
the followig:
"I was able to narrow the issue down to the mtu. If I set the mtu for
the wlan0 device to 1486 instead of 1500, the issue does not happen.
The size of frames that I see on Wireshark is exactly 1500 after
setting it to 1486."
Clearing the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE avoids the problem and
the ssh command works successfully after that.
Introduce a 'credit_size_workaround' field to ath10k_hw_params for
the QCA9377 SDIO, so that the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE
is not set in this case.
Tested with QCA9377 SDIO with firmware WLAN.TF.1.1.1-00061-QCATFSWPZ-1.
Fixes: 2f918ea986 ("ath10k: enable alt data of TX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211124131047.713756-1-festevam@denx.de
Currently 'ar' reference is not added in skb_cb during
WMI mgmt tx. Though this is generally not used during tx completion
callbacks, on interface removal the remaining idr cleanup callback
uses the ar ptr from skb_cb from mgmt txmgmt_idr. Hence
fill them during tx call for proper usage.
Also free the skb which is missing currently in these
callbacks.
Crash_info:
[19282.489476] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[19282.489515] pgd = 91eb8000
[19282.496702] [00000000] *pgd=00000000
[19282.502524] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[19282.783728] PC is at ath11k_mac_vif_txmgmt_idr_remove+0x28/0xd8 [ath11k]
[19282.789170] LR is at idr_for_each+0xa0/0xc8
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_after() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct.
Additionally fix the common helper, ieee80211_tx_info_clear_status(),
which was not clearing ack_signal, but the open-coded versions
did. Johannes Berg points out this bug was introduced by commit
e3e1a0bcb3 ("mac80211: reduce IEEE80211_TX_MAX_RATES") but was harmless.
Also drops the associated unneeded BUILD_BUG_ON()s, and adds a note to
carl9170 about usage.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com> [both CARL9170+P54USB on real HW]
Link: https://lore.kernel.org/r/20211118203839.1289276-1-keescook@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since firmware uses its own sequence number counters, we need to
use firmware number as well when mac80211 generates the ADD_BA
request packet. Indeed the firmware sequence counters tend to
slightly drift from the mac80211 ones because of firmware offload
features like ARP responses. This causes the starting sequence
number field of the ADD_BA request to be unaligned, and can possibly
cause issues with strict/picky APs.
To fix this, we retrieve the current firmware sequence number for
a given TID through the smd_trigger_ba API, and use that number as
replacement of the mac80211 starting sequence number.
This change also ensures that any issue in the smd *ba procedures
will cause the ba action to properly fail, and remove useless call
to smd_trigger_ba() from IEEE80211_AMPDU_RX_START.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637604251-11763-1-git-send-email-loic.poulain@linaro.org
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131 ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct. Additionally split up a later
field-spanning memset() so that memset() can reason about the size.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118202416.1286046-1-keescook@chromium.org
This reverts commit 46e46db313. Mark reported
that it breaks QCA6390 hw2.0 on Dell XPS 13 9310:
[ 5.537034] ath11k_pci 0000:72:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 5.537038] ath11k_pci 0000:72:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 5.537236] ath11k_pci 0000:72:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=255,variant=DE_1901 from ath11k/QCA6390/hw2.0/board-2.bin
[ 5.537255] ath11k_pci 0000:72:00.0: failed to fetch board-2.bin or board.bin from QCA6390/hw2.0
[ 5.537257] ath11k_pci 0000:72:00.0: qmi failed to fetch board file: -2
[ 5.537258] ath11k_pci 0000:72:00.0: failed to load board data file: -2
So we need to back to the drawing board and implement it so that backwards
compatiblity is not broken.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211124094316.9096-1-kvalo@codeaurora.org
In HE monitor capture, HAL_TLV_STATUS_PPDU_DONE is received
on processing multiple skb. Do not clear the ppdu_info
till the HAL_TLV_STATUS_PPDU_DONE is received.
This fixes below warning and packet drops in monitor mode.
"Rate marked as an HE rate but data is invalid: MCS: 6, NSS: 0"
WARNING: at
PC is at ieee80211_rx_napi+0x624/0x840 [mac80211]
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01693-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249433-10316-1-git-send-email-akolli@codeaurora.org
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118100033.8384-1-quic_wgong@quicinc.com
The ath11k driver currently sends vdev down to the firmware before
updating the channel context, which is followed by a vdev restart
command.
Sending vdev down is not required before sending a vdev restart,
because the firmware internally does vdev down when ath11k sends
a vdev restart command.
Firmware will happen crash while channel switch without this change.
Hence skip the vdev down command sending when updating the channel
context and then fix the firmware crash issue.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095901.8271-1-quic_wgong@quicinc.com
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
When connected to 6G mode AP, it does not have VHT/HT capabilities,
so the NSS is not set, then it is 1 by default.
This patch is to calculate the NSS with supported HE-MCS and NSS set
of HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01280-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095453.8030-1-quic_wgong@quicinc.com
Some firmware versions for WCN6855 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain, ath11k
should treat it as a world wide alpha code.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118094848.7776-1-quic_wgong@quicinc.com
With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath11k does MHI
register reading in this state. The issue was reported on Dell XPS 13
9310 but is seen also on XPS 15 and XPS 17 laptops.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041722.5271-1-bqiang@codeaurora.org
On some platforms it's not possible to allocate 32 MSI vectors for various
reasons, be it kernel configuration, VT-d disabled, buggy BIOS etc. So
ath11k was not able to use QCA6390 PCI devices on those platforms. Add
support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled. This
is because when interrupt migration happens, the msi_data may change.
However, msi_data is already programmed to rings during initial phase and
ath11k has no way to know that msi_data is changed during run time and
reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as QCA6390 doesn't set this flag too. Ath11k doesn't need to leave
IRQ enabled in suspend state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041714.5219-1-bqiang@codeaurora.org
This is to prepare for one MSI vector support. IRQ enable and disable
of CE and DP are done only in case of multiple MSI vectors.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041705.5167-1-bqiang@codeaurora.org
Like ATH11K_PCI_IRQ_CE0_OFFSET, define ATH11K_PCI_IRQ_DP_OFFSET for
DP to save the IRQ instead of base_vector from MSI config.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041655.5112-1-bqiang@codeaurora.org
This change adds two flags to indicate whether IRQ handler for CE
and DP can be called. This is because in one MSI vector case,
interrupt is not disabled in hif_stop and hif_irq_disable. Otherwise,
MHI interrupt is disabled too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041646.5060-1-bqiang@codeaurora.org
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts
are initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq
is called, so ath11k reads msi_data again after request_irq is called,
and then the correct msi_data is programmed into QCA6390 hardware
components. Without this change, spurious interrupt occurs in case of
one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI
vectors, ath11k always get the same msi_data before and after request_irq,
that's why this change is only required when one MSI vector is to be
supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041636.5008-1-bqiang@codeaurora.org
ath.git patches for v5.17. Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
The struct ath_hw member intr_txqs is never reset/assigned outside
of ath9k_hw_init_queues() and with the used bitwise-or in the interrupt
handling ar9002_hw_get_isr() accumulates all ever set interrupt flags.
Fix this by using a pure assign instead of bitwise-or for the
first line (note: intr_txqs is only evaluated in case ATH9K_INT_TX bit
is set).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211116220720.30145-1-ps.report@gmx.net
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd85133 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com
Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.
Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
The DMA buffers of dbring which is used for spectral/cfr
starts at certain offset from original kmalloc() returned buffer.
This is not cache line aligned.
And also driver tries to access the data that is immediately before
this offset address (i.e. buff->paddr) after doing dma map.
This will cause cache line sharing issues and data corruption,
if CPU happen to write back cache after HW has dma'ed the data.
Fix this by mapping a cache line aligned buffer to dma.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com
Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.
This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.
The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)
Ath11k uses both these configurations to disable credit flow for the
WMI path completely.
Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
There is a race condition whereby the tx completion handler can be invoked
before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we
could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because
it was not yet incremented). Ideally, this trace should be seen only if
mgmt tx has not happened but tx completion is received, and it is not
expected in this race condition.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com
Set proper values for max_regpower, max_power, max_antenna_gain as it
is because firmware will convert power values to 0.5dbm steps by
multiplying it with 2.
If txpower is not set, it will lead to cca stuck resulting in latency
issues for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com
In radio tap header, BAD FCS flag is not updated properly because
driver failed to update FCS_ERR flag in monitor mode.
In rx_desc, FCS_ERR information is available in rx_attention
structure and presence of this field indicates corresponding frame
failed FCS check.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com
When station connect to AP, the wmi command sequence is:
peer_create->vdev_start->vdev_up
and sequence of station disconnect fo AP is:
peer_delete->vdev_down->vdev_stop
The sequence of disconnect is not opposite of connect, it caused firmware
crash when it handle wmi vdev stop cmd when the AP is support TWT of
802.11 ax, because firmware need access the bss peer for vdev stop cmd.
[ 390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0
[ 390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g
[ 390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0
[ 390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0
[ 390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39
[ 399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0
[ 399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0
[ 399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0
[ 399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0
[ 399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0
The opposite sequence of disconnect should be:
vdev_down->vdev_stop->peer_delete
This patch change the sequence of disconnect for station as above
opposite sequence for QCA6390, firmware not crash again with this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com
parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com
Currently in ath11k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Unfortunately if this condition is true then the function returns without
setting parameters that follow the txrate. To address this issue remove the
return and instead invert the logic to set the txrate logic if
(arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in ath10k in commit 1cd6ba8ae3 ("ath10k: remove return
for NL80211_STA_INFO_TX_BITRATE").
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org
When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW
is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also
need to be set, otherwise it is invalid because spec in IEEE Std
802.11™‐2020 as below.
Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield
VHT Extended NSS BW Capable, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS
BW Support subfield of the VHT Capabilities Information field.
dmesg have a message without this patch:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not
set it in ieee80211_register_hw(). So it is better to set it in ath11k.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org
Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
Currently while loop is used to find the tx completion ring number and
it is not required since the tx ring mask and the group id can be combined
to directly fetch the ring number. Hence remove the while loop
and directly get the ring number from tx mask and group id.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org
Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org
Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE
from cacheable memory so that descriptors could be prefetched during
tx completion handling.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org
In datapath, add branch predictors where required in the process rx().
This protects high value rx path without having performance overhead.
Also while processing rx packets, the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org
The usage of quota variable inside ath11k_dp_rx_process_received_packets()
is redundant. Since we would queue only max packets to the list before
calling this function so it would never exceed quota. Hence removing
usage of quota variable.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org
The Active Pdev and CAC check are done for each msdu in
ath11k_dp_rx_process_received_packets which is a overhead.
To avoid this overhead, collect all msdus in a per mac msdu
list and pass to function.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org
In ath11k_dp_process_rx(), after processing rx_desc from
ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free()
is accessed everytime because of done flag is not set.
To avoid this additional access to ath11k_hal_srng_dst_num_free(),
increment total_msdu_reaped only when continuation is not set and
update done flag correspondingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org
In data path, to reduce the CPU cycles spending on descriptor access
wrapper function, changed those functions as static inline.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org
tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.
Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org
Host driver doesn't need to process CE8 interrupts (used
by target independently)
The volume of interrupts is huge within short interval,
CPU0 CPU1 CPU2 CPU3
14022188 0 0 0 GIC 71 Edge ce8
Hence disabling unused CE8 interrupt will improve CPU usage.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org
Currently the updated bandwidth for the peer will be configured
to the firmware after channel switch from the sta_rc_update_wk.
If the updated bandwidth is greater than the configured peer phymode
during the peer assoc may result firmware assert.
For example, initially AP is in HE40 mode and the peer phymode is
configured as MODE_11AX_HE40 during peer assoc. Now user change the
channel width to HE80 then, the peer bandwidth will be updated as
HE80 to the firmware.
This will trigger firmware assert due to peer bandwidth is greater than
the peer phymode.
Fix this issue by sending peer assoc command before setting the updated
peer bandwith to firmware.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com
Below compilation error is reported when built with W=1,
drivers/net/wireless/ath/ath11k/mac.c:5408:22: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter]
changed_flags is set, but left unused. So, remove unnecessary set.
Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636609967-5114-1-git-send-email-quic_seevalam@quicinc.com
In CE pipe cleanup, DMA memory gets freed by the aligned address
(base_addr_owner_space) which is wrong. It needs to be freed
by the address (base_addr_owner_space_unaligned) returned by
dma_alloc. So free the dma memory by the proper address.
This was found in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636561290-18966-1-git-send-email-quic_periyasa@quicinc.com
In STA kickout event processing, the peer object is protected
under spin lock BH. Release this lock after picking up the vdev_id
from the peer object instead after ieee80211_report_low_ack().
This will minimize the lock hold period which will improve
performance since base_lock is used across the data path.
This was found in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636560388-24955-1-git-send-email-quic_periyasa@quicinc.com
When there is an error in add interface process from
ath11k_mac_set_kickout(), the code attempts to handle a
fallback for add_interface. When this fallback succeeds, the
driver returns zero rather than error code. This leads to
success for the non created VAP. In cleanup, driver gets
remove interface callback for the non created VAP and
proceeds to self peer delete request which leads to FW assert.
Since it was already deleted on the fallback of add interface,
return the actual error code instead of fallback return code.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636558557-2874-1-git-send-email-quic_periyasa@quicinc.com
Firmware expects host to authorize the peer after the successful key
install. But host authorize the peer before the key install, this trigger
the firmware assert which leads to Q6 crash. To avoid this Q6 crash, host
should authorize the peer after the key install. So introduce is_authorized
in peer object to identify that peer is authorize or not. When
IEEE80211_STA_CONTROL_PORT flag is unset, peer move to authorize state
before the vdev up. When the same flag is set then peer move to authorize
state after vdev up. So added authorise check in ath11k_bss_assoc() to
handle the earlier state transition case. Also added the WMI authorize
procedure in ath11k_mac_op_sta_state() to handle the non-earlier state
transition case.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636554200-12345-1-git-send-email-quic_periyasa@quicinc.com
AUTH flag is needed when peer assoc command is sent from host in
security mode for non-assoc cases. Firmware will handle AUTH flag
when client is associating as AUTH flag will be set after key exchange.
For internally provided peer assoc commands from host, there won't be
any key exchange, so AUTH flag is expected to be set in host.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635177786-20854-1-git-send-email-quic_ramess@quicinc.com
HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message
was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from
bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in
the request message.
In commit 701e48a43e ("ath11k: add packet log support for QCA6390"), both
HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask
calculation is not valid for platforms which has multiple pdevs with 1 rxdma
per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it
to consider pdev_idx as well, to make it compatible for both single and multi
pd cases.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1
Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org
Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref
when ar->tx_cmd->odata is NULL. The patch adds a null check to
prevent such case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
ar5523_cmd+0x46a/0x581 [ar5523]
ar5523_probe.cold+0x1b7/0x18da [ar5523]
? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523]
? __pm_runtime_set_status+0x54a/0x8f0
? _raw_spin_trylock_bh+0x120/0x120
? pm_runtime_barrier+0x220/0x220
? __pm_runtime_resume+0xb1/0xf0
usb_probe_interface+0x25b/0x710
really_probe+0x209/0x5d0
driver_probe_device+0xc6/0x1b0
device_driver_attach+0xe2/0x120
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.
This was NOT tested on a real device.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu
To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.
Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.
To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org
It's more descriptive to use the actual enum used by the firmware instead of a
boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org
The linear mapping between the BD rate field and the driver's 5GHz
legacy rates table (wcn_5ghz_rates) does not only apply for the latter
four rates -- it applies to all eight rates.
Fixes: 6ea131acea ("wcn36xx: Fix warning due to bad rate_idx")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-3-benl@squareup.com
status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).
We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.
This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their beacons/probe responses at the higher four legacy rates
(24-54 Mbps), when using hardware scan offload:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
Modules linked in: wcn36xx [...]
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.107-g73909fa #1
Hardware name: Square, Inc. T2 (all variants) (DT)
Call trace:
dump_backtrace+0x0/0x148
show_stack+0x14/0x1c
dump_stack+0xb8/0xf0
__warn+0x2ac/0x2d8
warn_slowpath_null+0x44/0x54
ieee80211_rx_napi+0x744/0x8d8
ieee80211_tasklet_handler+0xa4/0xe0
tasklet_action_common+0xe0/0x118
tasklet_action+0x20/0x28
__do_softirq+0x108/0x1ec
irq_exit+0xd4/0xd8
__handle_domain_irq+0x84/0xbc
gic_handle_irq+0x4c/0xb8
el1_irq+0xe8/0x190
lpm_cpuidle_enter+0x220/0x260
cpuidle_enter_state+0x114/0x1c0
cpuidle_enter+0x34/0x48
do_idle+0x150/0x268
cpu_startup_entry+0x20/0x24
rest_init+0xd4/0xe0
start_kernel+0x398/0x430
---[ end trace ae28cb759352b403 ]---
Fixes: 8a27ca3947 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-2-benl@squareup.com
When deiniting the DXE hardware we should reset the block to ensure there
is no spurious DMA write transaction from the downstream WCNSS to upstream
MSM at a skbuff address we will have released.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-4-bryan.odonoghue@linaro.org
When unloading the driver we are not releasing the DMA descriptors which we
previously allocated.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-3-bryan.odonoghue@linaro.org
Right now we have a broken sequence where we enable DMA channel interrupts
which can be left enabled and never disabled if we hit an error path.
Worse still when we unload the driver, the DMA channel interrupt bits are
left intact. About the only saving grace here is that we do remember to
disable the wcnss interrupt when unload the driver.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-2-bryan.odonoghue@linaro.org
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
The end goal of the current buffer overflow detection work[0] is to gain
full compile-time and run-time coverage of all detectable buffer overflows
seen via array indexing or memcpy(), memmove(), and memset(). The str*()
family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this series
contains the foundational elements of several related buffer overflow
detection improvements by providing new common helpers and FORTIFY_SOURCE
changes needed to gain the introspection required for compiler visibility
into array sizes. Also included are a handful of already Acked instances
using the helpers (or related clean-ups), with many more waiting at the
ready to be taken via subsystem-specific trees[2]. The new helpers are:
- struct_group() for gaining struct member range introspection.
- memset_after() and memset_startat() for clearing to the end of structures.
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs.
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage under
GCC, and to prepare to fix the currently broken Clang support. Finishing
this work is part of the larger series[0], but depends on all the false
positives and buffer overflow bug fixes to have landed already and those
that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time
and run-time tests are added for FORTIFY_SOURCE and the mem*()-family
functions respectively. The compile time tests have found a legitimate
(though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage that
result in no known object code differences.
After this series (and the changes that have now landed via netdev
and usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds. However, due corner cases in
GCC[3] and Clang[4], I have not included the last two patches that turn
on these options, as I don't want to introduce any known warnings to
the build. Hopefully these can be solved soon.
[0] https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE
[2] https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/
[3] https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/
[4] https://bugs.llvm.org/show_bug.cgi?id=51682
[5] https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/
[6] https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/
-----BEGIN PGP SIGNATURE-----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=9xbT
-----END PGP SIGNATURE-----
Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"The end goal of the current buffer overflow detection work[0] is to
gain full compile-time and run-time coverage of all detectable buffer
overflows seen via array indexing or memcpy(), memmove(), and
memset(). The str*() family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this
series contains the foundational elements of several related buffer
overflow detection improvements by providing new common helpers and
FORTIFY_SOURCE changes needed to gain the introspection required for
compiler visibility into array sizes. Also included are a handful of
already Acked instances using the helpers (or related clean-ups), with
many more waiting at the ready to be taken via subsystem-specific
trees[2].
The new helpers are:
- struct_group() for gaining struct member range introspection
- memset_after() and memset_startat() for clearing to the end of
structures
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in
structs
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage
under GCC, and to prepare to fix the currently broken Clang support.
Finishing this work is part of the larger series[0], but depends on
all the false positives and buffer overflow bug fixes to have landed
already and those that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a
compile-time and run-time tests are added for FORTIFY_SOURCE and the
mem*()-family functions respectively. The compile time tests have
found a legitimate (though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage
that result in no known object code differences.
After this series (and the changes that have now landed via netdev and
usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds.
However, due corner cases in GCC[3] and Clang[4], I have not included
the last two patches that turn on these options, as I don't want to
introduce any known warnings to the build. Hopefully these can be
solved soon"
Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1]
Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2]
Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3]
Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4]
Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5]
Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6]
* tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
fortify: strlen: Avoid shadowing previous locals
compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer
treewide: Replace 0-element memcpy() destinations with flexible arrays
treewide: Replace open-coded flex arrays in unions
stddef: Introduce DECLARE_FLEX_ARRAY() helper
btrfs: Use memset_startat() to clear end of struct
string.h: Introduce memset_startat() for wiping trailing members and padding
xfrm: Use memset_after() to clear padding
string.h: Introduce memset_after() for wiping trailing members/padding
lib: Introduce CONFIG_MEMCPY_KUNIT_TEST
fortify: Add compile-time FORTIFY_SOURCE tests
fortify: Allow strlen() and strnlen() to pass compile-time known lengths
fortify: Prepare to improve strnlen() and strlen() warnings
fortify: Fix dropped strcpy() compile-time write overflow check
fortify: Explicitly disable Clang support
fortify: Move remaining fortify helpers into fortify-string.h
lib/string: Move helper functions out of string.c
compiler_types.h: Remove __compiletime_object_size()
cm4000_cs: Use struct_group() to zero struct cm4000_dev region
can: flexcan: Use struct_group() to zero struct flexcan_regs regions
...
Firmware can trigger a missed beacon indication, this is not the same as a
lost signal.
Flag to Linux the missed beacon and let the WiFi stack decide for itself if
the link is up or down by sending its own probe to determine this.
We should only be signalling the link is lost when the firmware indicates
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027232529.657764-1-bryan.odonoghue@linaro.org
An SMD capture from the downstream prima driver on WCN3680B shows the
following command sequence for connected scans:
- init_scan_req
- start_scan_req, channel 1
- end_scan_req, channel 1
- start_scan_req, channel 2
- ...
- end_scan_req, channel 3
- finish_scan_req
- init_scan_req
- start_scan_req, channel 4
- ...
- end_scan_req, channel 6
- finish_scan_req
- ...
- end_scan_req, channel 165
- finish_scan_req
Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1]
still sends finish_scan_req twice in a row or before init_scan_req. A
typical connected scan looks like this:
- init_scan_req
- start_scan_req, channel 1
- finish_scan_req
- init_scan_req
- start_scan_req, channel 2
- ...
- start_scan_req, channel 165
- finish_scan_req
- finish_scan_req
This patch cleans up scanning so that init/finish and start/end are always
paired together and correctly nested.
- init_scan_req
- start_scan_req, channel 1
- end_scan_req, channel 1
- finish_scan_req
- init_scan_req
- start_scan_req, channel 2
- end_scan_req, channel 2
- ...
- start_scan_req, channel 165
- end_scan_req, channel 165
- finish_scan_req
Note that upstream will not do batching of 3 active-probe scans before
returning to the operating channel, and this patch does not change that.
To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or
the 125ms max off-channel time in ieee80211_scan_state_decision.
[1]: commit d195d7aac0 ("wcn36xx: Ensure finish scan is not requested
before start scan") addressed one case of finish_scan_req being sent
without a preceding init_scan_req (the case of the operating channel
coinciding with the first scan channel); two other cases are:
1) if SW scan is started and aborted immediately, without scanning any
channels, we send a finish_scan_req without ever sending init_scan_req,
and
2) as SW scan logic always returns us to the operating channel before
calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice
at the end of a SW scan
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-4-benl@squareup.com
Without ieee80211_ops->flush implemented to empty HW queues, mac80211 will
do a 100ms dead wait after stopping SW queues, before leaving the operating
channel to resume a software connected scan[1].
(see ieee80211_scan_state_resume)
This wait is correctly included in the calculation for whether or not
we've exceeded max off-channel time, as it occurs after sending the null
frame with PS bit set. Thus, with 125 ms max off-channel time we only
have 25 ms of scan time, which technically isn't even enough to scan one
channel (although mac80211 always scans at least one channel per off-
channel window).
Moreover, for passive probes we end up spending at least 100 ms + 111 ms
(IEEE80211_PASSIVE_CHANNEL_TIME) "off-channel"[2], which exceeds the listen
interval of 200 ms that we provide in our association request frame. That's
technically out-of-spec.
[1]: Until recently, wcn36xx performed software (rather than FW-offloaded)
scanning when 5GHz channels are requested. This apparent limitation is now
resolved -- see commit 1395f8a6a4d5 ("wcn36xx: Enable hardware scan offload
for 5Ghz band").
[2]: in quotes because about 100 ms of it is still on-channel but with PS
set
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-3-benl@squareup.com
ATH10K chips are used it wide range of routers,
accesspoints, range extenders, network appliances.
On these embedded devices, calibration data is often
stored on the main system's flash and was out of reach
for the driver.
To bridge this gap, ath10k is getting extended to pull
the (pre-)calibration data through nvmem subsystem.
To do this, a nvmem-cell containing the information can
either be specified in the platform data or via device-tree.
Tested with:
Netgear EX6150v2 (IPQ4018 - pre-calibration method)
TP-Link Archer C7 v2 (QCA9880v2 - old calibration method)
Cc: Robert Marko <robimarko@gmail.com>
Cc: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016234609.1568317-1-chunkeey@gmail.com
Commit 6f4d70308e ("ath11k: support SMPS configuration for 6 GHz") changed
"if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap &
WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means
NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz.
However, WCN6855 supports 6 GHz but it does not support feature
NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for
WCN6855.
Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not
support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's
the only other device supporting 6 GHz band.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-3-jouni@codeaurora.org
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-2-johan@kernel.org
The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) supports channels 136 and 144.
However, these channels are missing in upstream. Add them here to get
closer to feature parity with prima.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-3-benl@squareup.com
The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) sends this feature bit.
As we wish to support the antenna diversity feature in upstream, we need
to set this bit as well.
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-2-benl@squareup.com
The channel scan list must be updated before triggering a hardware scan
so that firmware takes into account the regulatory info for each single
channel such as active/passive config, power, DFS, etc... Without this
the firmware uses its own internal default channel configuration, which
is not aligned with mac80211 regulatory rules, and misses several
channels (e.g. 144).
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635175328-25642-1-git-send-email-loic.poulain@linaro.org
Firmware link offload monitoring can be made to work in 3/4 cases by
switching on firmware feature bit WLANACTIVE_OFFLOAD
- Secure power-save on
- Secure power-save off
- Open power-save on
However, with an open AP if we switch off power-saving - thus never
entering Beacon Mode Power Save - BMPS, firmware never forwards loss
of beacon upwards.
We had hoped that WLANACTIVE_OFFLOAD and some fixes for sequence numbers
would unblock this but, it hasn't and further investigation is required.
Its possible to have a complete set of Secure power-save on/off and Open
power-save on/off provided we use Linux' link monitoring mechanism.
While we debug the Open AP failure we need to fix upstream.
This reverts commit c973fdad79f6eaf247d48b5fc77733e989eb01e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025093037.3966022-2-bryan.odonoghue@linaro.org
If the system is resumed because of an incoming packet, the wcn36xx RX
interrupts is fired before actual resuming of the wireless/mac80211
stack, causing any received packets to be simply dropped. E.g. a ping
request causes a system resume, but is dropped and so never forwarded
to the IP stack.
This change fixes that, disabling DMA interrupts on suspend to no pass
packets until mac80211 is resumed and ready to handle them.
Note that it's not incompatible with RX irq wake.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150496-19290-1-git-send-email-loic.poulain@linaro.org
The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).
To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.
Fixes: 84aff52e4f ("wcn36xx: Use sequence number allocated by mac80211")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com
All wcn36xx controllers are supposed to support HT40 (and SGI40),
This doubles the maximum bitrate/throughput with compatible APs.
Tested with wcn3620 & wcn3680B.
Cc: stable@vger.kernel.org
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634737133-22336-1-git-send-email-loic.poulain@linaro.org
On an open AP when you pull the plug on the AP, if we are not already in
BMPS mode then the firmware will not generate a disconnection event.
Instead we need to monitor for failure to enter BMPS and treat a string of
failures as connection loss.
Secure AP connections don't appear to demonstrate this behavior so the
work-around is limited to open APs only.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022140447.2846248-2-bryan.odonoghue@linaro.org
WCNSS RX DMA transfer support is limited to 3872 bytes, which is
enough for simple MPDUs (single MSDU), but not enough for cases
with A-MSDU (depending on max AMSDU size or max MPDU size).
In that case the MPDU is spread over multiple transfers, with the
first transfer containing the MPDU header and (at least) the first
A-MSDU subframe and additional transfer(s) containing the following
A-MSDUs. This can be handled with a series of flags to tagging the
first and last A-MSDU transfers.
In that case we have to bufferize and re-linearize the A-MSDU buffers
into a proper MPDU skb before forwarding to mac80211 (in the same way
as it is done in ath10k).
This change also includes sanity check of the buffer descriptor to
prevent skb overflow.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634557705-11120-1-git-send-email-loic.poulain@linaro.org
Until now, offload scanning for 5Ghz channels was considered broken.
However it was mostly a driver issue, caused by bad reporting of the
beacons/probe-resp bands and frequencies, which has been fixed.
We can now allow offload scan for 5GHz band, this reduces the scanning
time comparing to software driven scanning.
Note that offloaded scan is limited to 48 channels, check for this.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-2-git-send-email-loic.poulain@linaro.org
For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).
For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).
The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.
This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Commit 9af7c32cec ("ath10k: add target IRAM recovery feature support")
introduced a new firmware feature flag ATH10K_FW_FEATURE_IRAM_RECOVERY. But
this caused ath10k_pci module load to fail if ATH10K_FW_CRASH_DUMP_RAM_DATA bit
was not enabled in the ath10k coredump_mask module parameter:
[ 2209.328190] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 2209.434414] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 2209.547191] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.9.0.2-00099 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 cbade90a
[ 2210.896485] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 0:1 crc32 a040efc2
[ 2213.603339] ath10k_pci 0000:02:00.0: failed to copy target iram contents: -12
[ 2213.839027] ath10k_pci 0000:02:00.0: could not init core (-12)
[ 2213.933910] ath10k_pci 0000:02:00.0: could not probe fw (-12)
And by default coredump_mask does not have ATH10K_FW_CRASH_DUMP_RAM_DATA
enabled so anyone using a firmware with iram-recovery feature would fail. To my
knowledge only QCA9984 firmwares starting from release 10.4-3.9.0.2-00099
enabled the feature.
The reason for regression was that ath10k_core_copy_target_iram() used
ath10k_coredump_get_mem_layout() to get the memory layout, but when
ATH10K_FW_CRASH_DUMP_RAM_DATA was disabled it would get just NULL and bail out
with an error.
While looking at all this I noticed another bug: if CONFIG_DEV_COREDUMP is
disabled but the firmware has iram-recovery enabled the module load fails with
similar error messages. I fixed that by returning 0 from
ath10k_core_copy_target_iram() when _ath10k_coredump_get_mem_layout() returns
NULL.
Tested-on: QCA9984 hw2.0 PCI 10.4-3.9.0.2-00139
Fixes: 9af7c32cec ("ath10k: add target IRAM recovery feature support")
Signed-off-by: Abinaya Kalaiselvan <akalaise@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211020075054.23061-1-kvalo@codeaurora.org
Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^
Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.
Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.
Fixes: e263bdab9c ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org
Second set of patches for v5.16 and this time we have a big one. We
have the new Realtek driver rtw89 with over 90 kLOC and also over 150
patches for mt76. ath9k also got few new small features. And the usual
cleanups and fixes all over.
Major changes:
rtw89
* new Realtek 802.11ax driver
* supports Realtek 8852AE 802.11ax 2x2 chip
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
mt76
* mt7921 aspm support
* mt7921 testmode support
* mt7915 LED support
* mt7921 6GHz band support
* support for eeprom data in DT
* mt7915 TWT support
* mt7921s SDIO support
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmFybvwVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b8VoH/ikpKrYdhCwEHwaRHEiieejhD1w+
kvUhiQP/oL7q/4WVUzEnzv5BWQm1D7gHMmVvSdfjfdPuw7F085p6rQDCs99RlMo6
pUv6VllvuZa8XpIrQzdWbXbWv041cQA97wS5QNeEfiIvlwzw48Sfj2ANgPHRJy5a
z93ZhOeS5VL1h+1ki6uuGS0MoOaNhzPazb3kH7U2QkuuiP5BTvUw8nW9sQIaBEEg
UzdEzLjwhbZJtmIFs4dAkOKX2+ANrS09Zl0c9530ShwZB4RXTESv+OybQrcYNBUw
2RlGT0g8LYX7QJq/hJpJuylH7s/WrMZVDo07NBbfyOc2R/bi7R54S8zBInI=
=tjnh
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Second set of patches for v5.16 and this time we have a big one. We
have the new Realtek driver rtw89 with over 90 kLOC and also over 150
patches for mt76. ath9k also got few new small features. And the usual
cleanups and fixes all over.
Major changes:
rtw89
* new Realtek 802.11ax driver
* supports Realtek 8852AE 802.11ax 2x2 chip
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
mt76
* mt7921 aspm support
* mt7921 testmode support
* mt7915 LED support
* mt7921 6GHz band support
* support for eeprom data in DT
* mt7915 TWT support
* mt7921s SDIO support
* tag 'wireless-drivers-next-2021-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (213 commits)
zd1201: use eth_hw_addr_set()
wl3501_cs: use eth_hw_addr_set()
ray_cs: use eth_hw_addr_set()
...
====================
Link: https://lore.kernel.org/r/20211022075845.0E679C4360D@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Do the special encoding on the stack, then copy the address.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-6-kuba@kernel.org
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Do the special encoding on the stack, then copy the address.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-5-kuba@kernel.org
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert wireless from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-3-kuba@kernel.org
ath.git patches for v5.16. Major changes:
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
The 0-element arrays that are used as memcpy() destinations are actually
flexible arrays. Adjust their structures accordingly so that memcpy()
can better reason able their destination size (i.e. they need to be seen
as "unknown" length rather than "zero").
In some cases, use of the DECLARE_FLEX_ARRAY() helper is needed when a
flexible array is alone in a struct.
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: GR-QLogic-Storage-Upstream@marvell.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Fabio Aiuto <fabioaiuto83@gmail.com>
Cc: Ross Schmidt <ross.schm.dev@gmail.com>
Cc: Marco Cesati <marcocesati@gmail.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
coccicheck complains about the use of snprintf() in sysfs show functions.
Fix the coccicheck warning:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634095651-4273-1-git-send-email-wangqing@vivo.com
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
The devm_kmemdup() function doesn't return error pointers, it returns
NULL on error.
Fixes: eb3a97a69b ("ath9k: fetch calibration data via nvmem subsystem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011123533.GA15188@kili
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011054919.77071-1-bqiang@codeaurora.org
The common DT property can be used to limit the available channels
but ath9k has to manually call wiphy_read_of_freq_limits().
I would have put this into ath9k_of_init(). But it didn't work there.
The reason is that in ath9k_of_init() the channels and bands are not yet
registered in the wiphy struct. So there isn't any channel to flag as
disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211009212847.1781986-1-chunkeey@gmail.com
Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.
This is a theoretical fix found during code review, no visible impact.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org
When doing "rmmod ath11k_pci", ath11k performs global SOC reset
and MHI reset, where 0 address access is captured by IOMMU. See
log below:
...
[ 133.953860] ath11k_pci 0000:02:00.0: setting mhi state: DEINIT(1)
[ 133.959714] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
[ 133.973854] ath11k_pci 0000:02:00.0: MHISTATUS 0xff04
[ 133.974095] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
...
This issue is also observed in SSR process, cause a similar
sequence as above is performed.
Such an invalid access occurs because, during rmmod or SSR, MSI
address is cleared but HW MSI functionality not disabled, thus HW
target is able to raise an MSI transaction with 0 as MSI address.
So it can be fixed by simply disabling MSI before reset. For SSR,
since MSI functionality is still needed after target is brought
back, we need to reenable it.
Also change naming of some interfaces related.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-5-jouni@codeaurora.org
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Variable fw_size is being assigned a value that is never read and
being re-assigned a new value in the next statement. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Fixes: 336e7b53c8 ("ath11k: clean up BDF download functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006105529.1011239-1-colin.king@canonical.com
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Stephen reported that ath11k was failing to build on m68k and xtensa:
In file included from <command-line>:0:0:
In function 'ath11k_peer_assoc_h_smps',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2362:2:
include/linux/compiler_types.h:317:38: error: call to '__compiletime_assert_650' declared with attribute error: FIELD_GET: type of reg too small for mask
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/compiler_types.h:298:4: note: in definition of macro '__compiletime_assert'
prefix ## suffix(); \
^
include/linux/compiler_types.h:317:2: note: in expansion of macro '_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^
include/linux/bitfield.h:52:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \
^
include/linux/bitfield.h:108:3: note: in expansion of macro '__BF_FIELD_CHECK'
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/net/wireless/ath/ath11k/mac.c:2079:10: note: in expansion of macro 'FIELD_GET'
smps = FIELD_GET(IEEE80211_HE_6GHZ_CAP_SM_PS,
Fix the issue by using le16_get_bits() to specify the size explicitly.
Fixes: 6f4d70308e ("ath11k: support SMPS configuration for 6 GHz")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmFeqCYVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b1+QIAKeCfq25i6ObhdgKP7etAHyaOupP
0wKxXwuOMLllwUSDp/1vyONqMgNbpurXlGzqcwG2fRyljZouuuzAM/WUxtSETVEC
TaXYhoX7+u0DuVZ+QvREL0fK+jBB2qbpRpAneNPQ+nvjND5dVm233NwZ4oG65Z4f
qQC21WeP6rfi870Bj5ycmGIWbb+OVT0B7FHfNzy5tSkcCFmlKZBfP7p6raUyy6/Z
0EBosxEd5FWjAHbWHXLGtXb+k/48ntcFyCswa9qMBjVawahgNfXGG1JwceHFMRvE
fwNMweWj4M5QVs7jBZoQaxijBXUPjJdp/2adybgIpgQp50FmlC8uyRSe9YQ=
=yAni
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity complains that a constant variable guards dead code. In fact,
mpdu_buf is set NULL and never updated.
4834err_merge_fail:
null: At condition mpdu_buf, the value of mpdu_buf must be NULL.
dead_error_condition: The condition mpdu_buf cannot be true.
CID 92162 (#1 of 1): 'Constant' variable guards dead code (DEADCODE)
dead_error_line: Execution cannot reach the expression decap_format !=
DP_RX_DECAP_TYPE_RAW inside this statement: if (mpdu_buf && decap_forma....
Local variable mpdu_buf is assigned only once, to a constant value, making it
effectively constant throughout its scope. If this is not the intent, examine
the logic to see if there is a missing assignment that would make mpdu_buf not
remain constant.
4835 if (mpdu_buf && decap_format != DP_RX_DECAP_TYPE_RAW) {
Fix this by removing mpdu_buf and unreachable code.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927150743.19816-1-tim.gardner@canonical.com
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
Sometimes, in yet unknown cases the wifi chip stops working. To allow a
watchdog in userspace to easily and quickly reset the wifi chip, add the
according functionality to userspace. A reset can then be triggered
via:
$ echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/reset
The number of user resets can further be tracked in the row "User reset"
in the same file.
So far people usually used "iw scan" to fix ath9k chip hangs from
userspace. Which triggers the ath9k_queue_reset(), too. The reset file
however has the advantage of less overhead, which makes debugging bugs
within ath9k_queue_reset() easier.
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-2-linus.luessing@c0d3.blue
