For packets scheduled to RPM and LBK, NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL]
selects the TL3 or TL2 scheduling level as the one used for link/channel
selection and backpressure. For each scheduling queue at the selected
level: Setting NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG[ENA] = 1 allows
the TL3/TL2 queue to schedule packets to a specified RPM or LBK link
and channel.
There is an issue in the code where NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL]
is set to TL3 where as the NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG is
configured for TL2 queue in some cases. As a result packets will not
transmit on that link/channel. This patch fixes the issue by configuring
the NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG register depending on the
NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL] value.
Fixes: caa2da34fd ("octeontx2-pf: Initialize and config queues")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20220802142813.25031-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP messages like SYNC, FOLLOW_UP, DELAY_REQ are of size 58 bytes.
Using a minimum packet length as 64 makes NIX to pad 6 bytes of
zeroes while transmission. This is causing latest ptp4l application to
emit errors since length in PTP header and received packet are not same.
Padding upto 3 bytes is fine but more than that makes ptp4l to assume
the pad bytes as a TLV. Hence reduce the size to 60 from 64.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20220729092457.3850-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 35d099da41, reversing
changes made to 58d8bcd47e.
I wrongly applied that to the net-next tree instead of the intended
target tree (net). Reverting it on net-next.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.
Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.
Fixes: e638a83f16 ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.
Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.
Fixes: e638a83f16 ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NPC exact match table can support more entries than RPM
dmac filters. This requires field size of DMAC filter count
and index to be increased.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 2ef8e39f58, reversing
changes made to e7ce9fc9ad.
There are build warnings here which break the normal
build due to -Werror. Ratheesh was nice enough to quickly
follow up with fixes but didn't hit all the warnings I
see on GCC 12 so to unlock net-next from taking patches
let get this series out for now.
Link: https://lore.kernel.org/r/20220707013201.1372433-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NPC exact match table can support more entries than RPM
dmac filters. This requires field size of DMAC filter count
and index to be increased.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 6e144b47f5 (octeontx2-pf: Add support for adaptive interrupt coalescing)
Added support for VF interfaces as well.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes the following patchsets:
- bitmap: optimize bitmap_weight() usage(w/o bitmap_weight_cmp), from me;
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab;
- include/linux/find: Fix documentation, from Anna-Maria Behnsen;
- bitmap: fix conversion from/to fix-sized arrays, from me;
- bitmap: Fix return values to be unsigned, from Kees Cook.
It has been in linux-next for at least a week with no problems.
-----BEGIN PGP SIGNATURE-----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=U7DN
-----END PGP SIGNATURE-----
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
Added support for adaptive IRQ coalescing. It uses net_dim
algorithm to find the suitable delay/IRQ count based on the
current packet rate.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20220517044055.876158-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some places, octeontx2 code calls bitmap_weight() to check if any bit of
a given bitmap is set. It's better to use bitmap_empty() in that case
because bitmap_empty() stops traversing the bitmap as soon as it finds
first set bit, while bitmap_weight() counts all bits unconditionally.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion Queue Entry(CQE) is a descriptor written
by hardware to notify software about the send and
receive completion status. The CQE can be of size
128 or 512 bytes. A 512 bytes CQE can hold more receive
fragments pointers compared to 128 bytes CQE. This
patch enables to modify CQE size using:
<ethtool -G cqe-size N>.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cn10k hardware ptp timestamp format has been modified primarily
to support 1-step ptp clock. The 64-bit timestamp used by hardware is
split into two 32-bit fields, the upper one holds seconds, the lower
one nanoseconds. A new register (PTP_CLOCK_SEC) has been added that
returns the current seconds value. The nanoseconds register PTP_CLOCK_HI
resets after every second. The cn10k RPM block provides Rx/Tx timestamps
to the NIX block using the new timestamp format. The software can read
the current timestamp in nanoseconds by reading both PTP_CLOCK_SEC &
PTP_CLOCK_HI registers.
This patch provides support for new timestamp format.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TC feature for VFs also. When MCAM
rules are allocated for a VF then either TC or ntuple
filters can be used. Below are the commands to use
TC feature for a VF(say lbk0):
devlink dev param set pci/0002:01:00.1 name mcam_count value 16 \
cmode runtime
ethtool -K lbk0 hw-tc-offload on
ifconfig lbk0 up
tc qdisc add dev lbk0 ingress
tc filter add dev lbk0 parent ffff: protocol ip flower skip_sw \
dst_mac 98:03:9b:83:aa:12 action police rate 100Mbit burst 5000
Also to modify any fields of the hardware context with
NIX_AQ_INSTOP_WRITE command then corresponding masks of those
fields must be set as per hardware. This was missing in
ingress ratelimiting context. This patch sets those masks also.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data centric bridging designed to eliminate packet loss due to
queue overflow by adding enhancements to ethernet network such as
proprity flow control etc. This patch adds support for management
of Priority flow control(PFC) on Octeontx2 and CN10K interfaces.
To enable PFC for all priorities
dcb pfc set dev eth0 prio-pfc all:on/off
To enable PFC on selected priorites
dcb pfc set dev eth0 prio-pfc 0:on/off 1:on/off ..7:on/off
With the ntuple commands user can map Priority to receive queues.
On queue overflow NIX will assert backpressure such that PFC pause frames
are genarated with mapped priority.
To map priority 7 to Queue 1
ethtool -U eth0 flow-type ether dst xx:xx:xx:xx:xx:xx vlan 0xe00a
m 0x1fff queue 1
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation is such that 802.3x pause frames are
enabled by default. As CGX and RPM blocks support PFC
(priority flow control) also, instead of driver enabling one
between them enable them upon request from PF or its VFs.
Also add support to disable pause frames in driver unbind.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool rx-buf-len is for setting receive buffer size,
support setting it via ethtool -G parameter and getting
it via ethtool -g parameter.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF forwards its VF messages to AF and corresponding
replies from AF to VF. AF sets proper error code in the
replies after processing message requests. Currently PF
checks the error codes in replies and sends invalid
message to VF. This way VF lacks the information of
error code set by AF for its messages. This patch
changes that such that PF simply forwards AF replies
so that VF can handle error codes.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While freeing SQB pointers to aura, driver first memcpy to
target address and then triggers lmtst operation to free pointer
to the aura. We need to ensure(by adding dmb barrier)that memcpy
is finished before pointers are freed to the aura. This patch also
adds the missing sq context structure entry in debugfs.
Fixes: ef6c8da71e ("octeontx2-pf: cn10K: Reserve LMTST lines per core")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is removed respective PTP resources are not
being freed currently. This patch fixes it.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
cgroup.h (therefore swap.h, therefore half of the universe)
includes bpf.h which in turn includes module.h and slab.h.
Since we're about to get rid of that dependency we need
to clean things up.
v2: drop the cpu.h include from cacheinfo.h, it's not necessary
and it makes riscv sensitive to ordering of include files.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20211120035253.72074-1-kuba@kernel.org/ # v1
Link: https://lore.kernel.org/all/20211120165528.197359-1-kuba@kernel.org/ # cacheinfo discussion
Link: https://lore.kernel.org/bpf/20211202203400.1208663-1-kuba@kernel.org
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mii ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but octeontx2-nicvf introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the VF and PF side of this driver differently, with one being
a loadable module and the other one built-in results in a link failure
for the common PTP driver:
ld.lld: error: undefined symbol: __this_module
>>> referenced by otx2_ptp.c
>>> net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a
>>> referenced by otx2_ptp.c
>>> net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a
Move the otx2_ptp.c code into a separate module that gets built for
both configurations, making it built-in if at least one of the other
two is built-in.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the logic of configuring hardware
maximum transmit frame size and receive frame size.
This simplifies the logic to calculate receive buffer
size and using cqe descriptor of different size.
Also additional size of skb_shared_info structure is
allocated for each receive buffer pointer given to
hardware which is not necessary. Hence change the
size calculation to remove the size of
skb_shared_info. Add a check for array out of
bounds while adding fragments to the network stack.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx*
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable pin is being initialized with a value that is never
read, it is being updated later on in only one case of a switch
statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds XDP_PASS, XDP_TX, XDP_DROP and XDP_REDIRECT support
for netdev PF.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
