The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready.
This is the first register the driver reads from. Reading implausible
values (all bits set or unset) can be caused by the chip starting up
after power on, waking up after sleep, or by the chip not being preset
at all. Add check for implausible register content
mcp251xfd_reg_invalid() to the regmap_read_poll_timeout() loop.
In case of a regmap_read_poll_timeout() returns a fatal error (and not
a timeout), forward it to the caller.
As mcp251xfd_chip_wait_for_osc_ready() will be called after the probe
function has finished, (currently during ifup), move error message
about failed chip detection from there into the probe function.
Link: https://lore.kernel.org/all/20220207131047.282110-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd_chip_stop() function tries the best to stop the chip and
put it into sleep mode. It continues, even if some intermediate steps
fail. As none of the callers use the return value, let this function
return void.
Link: https://lore.kernel.org/all/20220207131047.282110-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd driver supports runtime PM enabled kernels, but also
works on !CONFIG_PM configurations.
This patch simplifies the runtime PM handling in the
mcp251xfd_unregister(). In the CONFIG_PM case, runtime PM has been
enabled in the mcp251xfd_probe() function, so we can disable it here.
For !CONFIG_PM builds call mcp251xfd_clks_and_vdd_disable() directly.
Link: https://lore.kernel.org/all/20220207131047.282110-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
MCP251XFD_REG_OSC is the first register the driver reads from. The
chip may be in deep sleep and the SPI transfer (i.e. the assertion of
the CS) will wake the chip up. This takes about 3ms. The CRC of this
transfer is wrong, or there isn't any chip at all, in this case the
CRC will be wrong, too. The driver ignores the CRC error and returns
the read data to the caller.
To avoid any confusion, this patch changes the
mcp251xfd_regmap_crc_read() function to only ignore the CRC error if
solely the OSC register is read. So when reading more than the OSC
registers at once, CRC errors are not ignored.
Link: https://lore.kernel.org/all/20220207131047.282110-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames mcp251xfd_osc_invalid() to mcp251xfd_reg_invalid(),
as it will be used for other registers than the "osc" register in a
later patch.
This patch also moves this function to more towards the beginning of
the file, to be available for other functions, too.
Link: https://lore.kernel.org/all/20220207131047.282110-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
Link: https://lore.kernel.org/all/20220105154300.1258636-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
Link: https://lore.kernel.org/all/20220105154300.1258636-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch
| dd8088d5a8 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
Link: https://lore.kernel.org/all/20220105154300.1258636-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Link: https://lore.kernel.org/all/20220105154300.1258636-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec2 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When deferred the reason is saved for further debugging. Besides that,
it's fine to call dev_err_probe() in ->probe() when error code is
known. Convert the driver to use dev_err_probe().
Link: https://lore.kernel.org/all/20211206165542.69887-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/all/20211206165542.69887-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's not clear what was the intention of redundant usage of IS_ERR()
around the clock pointer since with the error check of devm_clk_get()
followed by bailout it can't be invalid,
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). It will allow to switch to device properties
approach in the future.
Link: https://lore.kernel.org/all/20211206165542.69887-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the error handling for mcp251xfd_chip_rx_int_enable().
Instead just returning the error, properly shut down the chip.
Link: https://lore.kernel.org/all/20211106201526.44292-2-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function can_rx_offload_threaded_irq_finish() is needed to trigger
the NAPI thread to deliver read CAN frames to the networking stack.
This patch adds the missing call to can_rx_offload_threaded_irq_finish()
in case of a bus off, before leaving the interrupt handler to avoid
packet starvation.
Link: https://lore.kernel.org/all/20211106201526.44292-1-mkl@pengutronix.de
Fixes: 30bfec4fec ("can: rx-offload: can_rx_offload_threaded_irq_finish(): add new function to be called from threaded interrupt")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the patch 07ff4aed01 ("time/timecounter: Mark 1st argument of
timecounter_cyc2time() as const") some instances of the struct
mcp251xfd_priv can be marked as const. This patch marks these as
const.
Link: https://lore.kernel.org/r/20210813091027.159379-1-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/r/20210729141246.GA1267@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/r/20210531084444.1785397-1-mkl@pengutronix.de
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After reading all CAN frames from the controller in the IRQ handler
and storing them into a skb_queue, the driver calls napi_schedule().
In the napi poll function the skb from the skb_queue are then pushed
into the networking stack.
However if napi_schedule() is called from a threaded IRQ handler this
triggers the following error:
| NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
To avoid this, create a new rx-offload
function (can_rx_offload_threaded_irq_finish()) with a call to
local_bh_disable()/local_bh_enable() around the napi_schedule() call.
Convert all drivers that call can_rx_offload_irq_finish() from
threaded IRQ context to can_rx_offload_threaded_irq_finish().
Link: https://lore.kernel.org/r/20210724204745.736053-4-mkl@pengutronix.de
Suggested-by: Daniel Glöckner <dg@emlix.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adding a skb to the skb_queue in rx-offload requires to take a lock.
This commit avoids this by adding an unlocked skb queue that is
appended at the end of the ISR. Having one lock at the end of the ISR
should be OK as the HW is empty, not about to overflow.
Link: https://lore.kernel.org/r/20210724204745.736053-2-mkl@pengutronix.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Co-developed-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case an error occurred in the IRQ handler, the chip status is
dumped via devcoredump and all IRQs are disabled, but the chip stays
powered for further analysis.
The chip is in an undefined state and will not receive any CAN frames,
so shut down the timestamping worker, which reads the TBC register
regularly, too. This avoids any CRC read error messages if there is a
communication problem with the chip.
Fixes: efd8d98dfb ("can: mcp251xfd: add HW timestamp infrastructure")
Link: https://lore.kernel.org/r/20210724155131.471303-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the following clang warning, by marking the functions
as maybe unused. gcc doesn't complain about unused inline functions.
| drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c:564:1: warning: unused function 'mcp251xfd_chip_set_mode_nowait' [-Wunused-function]
| mcp251xfd_chip_set_mode_nowait(const struct mcp251xfd_priv *priv,
| ^
| 1 warning generated.
Link: https://lore.kernel.org/r/20210514153741.1958041-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch silences the following clang warning:
| drivers/net/can/spi/mcp251x.c:1333:17: warning: cast to smaller integer type
| 'enum mcp251x_model' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| priv->model = (enum mcp251x_model)match;
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8de29a5c34 ("can: mcp251x: Make use of device property API")
Link: https://lore.kernel.org/r/20210504200520.1179635-2-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since 8ce8c0abcb the driver queues work via priv->restart_work when
resuming after suspend, even when the interface was not previously
enabled. This causes a null dereference error as the workqueue is only
allocated and initialized in mcp251x_open().
To fix this we move the workqueue init to mcp251x_can_probe() as there
is no reason to do it later and repeat it whenever mcp251x_open() is
called.
Fixes: 8ce8c0abcb ("can: mcp251x: only reset hardware as required")
Link: https://lore.kernel.org/r/17d5d714-b468-482f-f37a-482e3d6df84e@kontron.de
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[mkl: fix error handling in mcp251x_stop()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we converted this code to use dev_err_probe() we accidentally
removed a return. It means that if devm_clk_get() it will lead to an
Oops when we call clk_get_rate() on the next line.
Fixes: cf8ee6de25 ("can: mcp251xfd: mcp251xfd_probe(): use dev_err_probe() to simplify error handling")
Link: https://lore.kernel.org/r/YJANZf13Qxd5Mhr1@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCP251XFD_REG_TBC is the time base counter register. It increments
once per SYS clock tick, which is 20 or 40 MHz. Observation shows that
if the lowest byte (which is transferred first on the SPI bus) of that
register is 0x00 or 0x80 the calculated CRC doesn't always match the
transferred one.
To reproduce this problem let the driver read the TBC register in a
high frequency. This can be done by attaching only the mcp251xfd CAN
controller to a valid terminated CAN bus and send a single CAN frame.
As there are no other CAN controller on the bus, the sent CAN frame is
not ACKed and the mcp251xfd repeats it. If user space enables the bus
error reporting, each of the NACK errors is reported with a time
stamp (which is read from the TBC register) to user space.
$ ip link set can0 down
$ ip link set can0 up type can bitrate 500000 berr-reporting on
$ cansend can0 4FF#ff.01.00.00.00.00.00.00
This leads to several error messages per second:
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 3a 86 da, CRC=0x7753) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=80 01 b4 da, CRC=0x5830) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 e9 23 db, CRC=0xa723) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=00 8a 30 db, CRC=0x4a9c) retrying.
| mcp251xfd spi0.0 can0: CRC read error at address 0x0010 (length=4, data=80 f3 43 db, CRC=0x66d2) retrying.
If the highest bit in the lowest byte is flipped the transferred CRC
matches the calculated one. We assume for now the CRC calculation in
the chip works on wrong data and the transferred data is correct.
This patch implements the following workaround:
- If a CRC read error on the TBC register is detected and the lowest
byte is 0x00 or 0x80, the highest bit of the lowest byte is flipped
and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Link: https://lore.kernel.org/r/20210406110617.1865592-5-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out the crc check into a separate function. This is
preparation for the next patch.
Link: https://lore.kernel.org/r/20210406110617.1865592-4-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch re-adds BQL support to the driver. Support for
netdev_xmit_more() will be added in a separate patch series.
Link: https://lore.kernel.org/r/20210406110617.1865592-3-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SPI host controllers do not support full-duplex SPI transfers.
The function mcp251x_spi_trans() does a full duplex transfer. It is
used in several places in the driver, where a TX half duplex transfer
is sufficient.
To fix support for half duplex SPI host controllers, this patch
introduces a new function mcp251x_spi_write() and changes all callers
that do a TX half duplex transfer to use mcp251x_spi_write().
Fixes: e0e25001d0 ("can: mcp251x: add support for half duplex controllers")
Link: https://lore.kernel.org/r/20210330100246.1074375-1-mkl@pengutronix.de
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reported-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses the previously added mcp251xfd_skb_set_timestamp()
function to convert the timestamp done by the CAN controller into a
proper skb hw timestamp.
Link: https://lore.kernel.org/r/20210304161209.2754463-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add the HW timestamping infrastructure. The mcp251xfd has a
free running timer of 32 bit width, running at max 40MHz, which wraps
around every 107 seconds. The current timestamp is latched into RX and
TEF objects automatically be the CAN controller.
This patch sets up a cyclecounter, timecounter and delayed worker
infrastructure (which runs every 45 seconds) to convert the timer into
a proper 64 bit based ns timestamp.
Link: https://lore.kernel.org/r/20210304160328.2752293-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the patches:
| 1f652bb6ba can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit
| 68c0c1c7f9 can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit
the setting of the UINC bit in the TEF and RX FIFO was batched into a
single SPI message consisting of several transfers. All transfers but
the last need to have the cs_change set to 1.
In the original patches the array of prepared transfers is send from
the beginning with the length depending on the number of read TEF/RX
objects. The cs_change of the last transfer is temporarily set to
0 during send.
This patch removes the modification of cs_change by preparing the last
transfer with cs_change to 0 and all other to 1. When sending the SPI
message the driver now starts with an offset into the array, so that
it always ends on the last entry in the array, which has the cs_change
set to 0.
Link: https://lore.kernel.org/r/20210304160328.2752293-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For easier debugging this patch adds dev coredump support to the
driver. A dev coredump is generated in case the chip fails to start or
an error in the interrupt handler is detected.
The dev coredump consists of all chip registers and chip memory, as
well as the driver's internal state of the TEF-, RX- and TX-FIFOs, it
can be analyzed with the mcp251xfd-dump tool of the can-utils:
https://github.com/linux-can/can-utils/tree/master/mcp251xfd
Link: https://lore.kernel.org/r/20210304160328.2752293-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
| 9420e1d495 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the following 4 patches
| 99842c9685 can: dev: can_rx_offload_get_echo_skb(): extend to return can frame length
| 9420e1d495 can: dev: can_get_echo_skb(): extend to return can frame length
| 1dcb6e57db can: dev: can_put_echo_skb(): extend to handle frame_len
| f0ef72febc can: dev: extend struct can_skb_priv to hold CAN frame length
the CAN echo SKB support was extended to hold the CAN frame
length (which is the length of the CAN frame on the wire). It is meant
as a helper for BQL support, to avoid the re-calculation of the frame
length before sending it and on TX-completion.
However if the CAN frame is send without the request to be looped back
the SKB is discarded in can_put_echo_skb() and the subsequent
can_get_echo_skb() and can_rx_offload_get_echo_skb() return 0 for the
CAN frame length. This results in BQL stalling the TX queue after a
few packages.
Until the BQL helpers can_get_echo_skb() and
can_rx_offload_get_echo_skb() are fixed, revert the BQL support for
the mcp251xfd driver.
This reverts commit 4162e18e94.
Fixes: 4162e18e94 ("can: mcp251xfd: add BQL support")
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20210228083347.28580-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch unifies the error messages:
- have a "." and the end of each message
- write controller with a small "c", if not the first word of an error
message.
Link: https://lore.kernel.org/r/20210128104644.2982125-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The published errata specify the maximum allowed SPI frequency to be
max 85% of (FSYSCLK/2). So there's no need to track known bad clock
settings in the driver. As the setup of known good values is a bit
tricky, keep them.
Link: https://lore.kernel.org/r/20210128104644.2982125-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the reference to the errata for both the mcp2517fd
and the mcp2518fd.
Fixes: f5b84dedf7 ("can: mcp25xxfd: mcp25xxfd_probe(): add SPI clk limit related errata information")
Link: https://lore.kernel.org/r/20210128104644.2982125-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In Classical CAN there are RTR frames. RTR frames have the RTR bit set, may
have a dlc != 0, but contain no data.
This patch optimizes the TX-path to not copy any data for RTR frames.
Link: https://lore.kernel.org/r/20210114153448.1506901-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In Classical CAN there are RTR frames. RTR frames have the RTR bit set, may
have a dlc != 0, but contain no data.
This patch changes the RX-path to no copy any data for RTR frames, so that the
data field in the CAN frame stays 0x0.
Link: https://lore.kernel.org/r/20210114153448.1506901-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN-FD frames have only specific frame length (0, 1, 2, 3, 4, 5, 6, 7, 8, 12,
16, 20, 24, 32, 48, 64). A CAN-FD frame provided by user space might not cover
the whole CAN-FD frame. To avoid sending garbage over the CAN bus the driver
pads the CAN frame with 0x0 (if MCP251XFD_SANITIZE_CAN is activated).
This patch cleans up the pad len calculation. Rounding to full u32 brings no
benefit, in case of CRC transfers, the hw_tx_obj->data is not aligned to u32
anyway.
Link: https://lore.kernel.org/r/20210114153448.1506901-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sizeof(u32) is hardcoded. It's better to use the config value from the
regmap.
It increases the size of target object, but it's flexible when new mcp chip
need other val_bytes.
Link: https://lore.kernel.org/r/20210122081334.213957-1-suyanjun218@gmail.com
Signed-off-by: Su Yanjun <suyanjun218@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack after queueing and after
transmission completion.
To avoid to calculate this length twice, extend can_rx_offload_get_echo_skb()
to return that value. Convert all users of this function, too.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack after queueing and after
transmission completion.
To avoid to calculate this length twice, extend can_get_echo_skb() to return
that value. Convert all users of this function, too.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a frame_len argument to can_put_echo_skb() which is used to save length of
the CAN frame into field frame_len of struct can_skb_priv so that it can be
later used after transmission completion. Convert all users of this function,
too.
Drivers which implement BQL call can_put_echo_skb() with the output of
can_skb_get_frame_len(skb) and drivers which do not simply pass zero as an
input (in the same way that NULL would be given to can_get_echo_skb()). This
way, we have a nice symmetry between the two echo functions.
Link: https://lore.kernel.org/r/20210111061335.39983-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-13-mkl@pengutronix.de
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
If alloc_canfd_skb() returns NULL, 'cfg' is an uninitialized variable, so we
should check 'skb' rather than 'cfd' after calling alloc_canfd_skb(priv->ndev,
&cfd).
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210113073100.79552-1-miaoqinglang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch fixes a TEF vs. TX race condition, by first updating the TEF
tail pointer in hardware, and then updating the driver internal pointer.
The same pattern exists in the RX-path, too. This should be no problem, as the
driver accesses the RX-FIFO from the interrupt handler only, thus the access is
properly serialized. Fix the order here, too, so that the TEF- and RX-path look
similar.
Fixes: 1f652bb6ba ("can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd driver uses a TX FIFO for sending CAN frames and a TX Event FIFO
(TEF) for completed TX-requests.
The TEF event handling in the mcp251xfd_handle_tefif() function has a race
condition. It first increments the tx-ring's tail counter to signal that
there's room in the TX and TEF FIFO, then it increments the TEF FIFO in
hardware.
A running mcp251xfd_start_xmit() on a different CPU might not stop the txqueue
(as the tx-ring still shows free space). The next mcp251xfd_start_xmit() will
push a message into the chip and the TX complete event might overflow the TEF
FIFO.
This patch changes the order to fix the problem.
Fixes: 68c0c1c7f9 ("can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
MCP251xFD supports internal loopback mode which can be used to verify CAN
functionality in the absence of a real CAN device.
Link: https://lore.kernel.org/r/20201201054019.11012-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mkl: mcp251xfd_get_normal_mode(): move CAN_CTRLMODE_LOOPBACK check to front]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reduce the number of separate SPI core requests when setting the UINC bit in
the TEF FIFO, and instead batch them up into a single SPI core request.
Link: https://lore.kernel.org/r/20201126132144.351154-6-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the struct mcp251xfd_tef_ring upwards, so that the union
mcp251xfd_write_reg_buf and struct spi_transfer can be made members of it.
Link: https://lore.kernel.org/r/20201126132144.351154-5-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the struct mcp251xfd_tef_ring member within the struct
mcp251xfd_priv into an array of length one. This way all rings (tef, tx and rx)
can be accessed in the same way.
Link: https://lore.kernel.org/r/20201126132144.351154-4-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It would directly return if the variable err equals to 0 or other errors.
Only when the err equals to -ETIMEDOUT it can reach the 'if (err)'
statement, so the 'if (err)' and last 'return -ETIMEDOUT' statements are
useless. Romove them.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1605605352-25298-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper functions can_len2dlc and can_dlc2len are only relevant for
CAN FD data length code (DLC) conversion.
To fit the introduced can_cc_dlc2len for Classical CAN we rename:
can_dlc2len -> can_fd_dlc2len to get the payload length from the DLC
can_len2dlc -> can_fd_len2dlc to get the DLC from the payload length
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The macro was always used together with can_dlc2len() which sanitizes the
given dlc value on its own.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-4-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).
Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During debugging it turned out that some people have setups where the SPI
communication is more prone to CRC errors.
Increase the severity of both the transfer retry and transfer failure message
to give users feedback without the need to recompile the driver with debug
enabled.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Link: http://lore.kernel.org/r/20201019190524.1285319-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all user facing strings from
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD", including:
- kconfig symbols
- name of kernel module
- DT and SPI compatible
[1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Link: https://lore.kernel.org/r/20200930091424.792165-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
