To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Evaluate the desired pixel clock polarity from the device tree.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The real and requested clock can differ and because it is used to
calculate PLL values, the real clock rate should be read.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename V4L2 async notifier functions, replacing "notifier" with "nf" and
removing "_subdev" at the end of the function names adding subdevs as you
can only add subdevs to a notifier. Also wrap and otherwise clean up long
lines.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (imx7)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-9-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TD1997x chip retains vper, hper and hsper register values when the
HDMI source is disconnected. Use a different means of checking if the
link is still valid.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The colon isn't followed by anything here.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For ov8856 working with ACPI, it does not depend on the reset gpio
and regulator to do reset and power control, so should get the gpio
and regulator for non-ACPI cases only, otherwise it will break ov8856
with ACPI.
[Sakari Ailus: Wrap a line over 80 chars.]
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Cc: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the RGB digital gains of ov9734 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the RGB digital gains of ov2740 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the pre_streamon callback to transition the transmitter to either
LP-11 or LP-111 mode if supported by the sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.
Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.
Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to media bus pixel codes definition, data formats on serial
busses should be described with one bus sample per pixel.
Documentation/userspace-api/media/v4l/subdev-formats.rst states:
"The media bus pixel codes document parallel formats. Should the pixel
data be transported over a serial bus, the media bus pixel code that
describes a parallel format that transfers a sample on a single clock
cycle is used. For instance, both MEDIA_BUS_FMT_BGR888_1X24 and
MEDIA_BUS_FMT_BGR888_3X8 are used on parallel busses for transferring an
8 bits per sample BGR data, whereas on serial busses the data in this
format is only referred to using MEDIA_BUS_FMT_BGR888_1X24. This is
because there is effectively only a single way to transport that
format on the serial busses."
Some MIPI CSI receivers strictly obey this definition and declare
support for only *1X_* formats.
Hence, complement the supported media bus formats with their 1X16 versions
(currently applicable to yuyv, uyvy) to enhance interoperability with CSI
receivers.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the OmniVisison ov9282
black&white image sensor.
The camera sensor uses the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 1280x720 @ 30fps
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the Sony imx412 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 4056x3040 @ 30fps
- supported bayer order output:
- SRGGB10
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the Sony imx335 image sensor.
ThE camera sensor uses the i2c bus for control and the csi-2
bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 2592x1940 @ 30fps
- supported bayer order output:
- SRGGB12
[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Captured video would be out of sync when using the adv7280 with
the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) had to
be configured properly to ensure BT.656-4 compatibility.
An error in the adv7280 reference manual suggested that EAV/SAV mode
was enabled by default, however upon inspecting register 0x31, it was
determined to be disabled by default.
[fabio: Introduce "adv,force-bt656-4" to not affect the existing users]
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a reset input that can be controlled by GPIO. Let's add it
to let the driver control it if required.
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
deleted the repeated word 'the' in the comments.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10635 image sensor embedded in the camera module is currently
reset after the MAX9271 initialization with two long delays that were
most probably not correctly characterized.
Re-work the image sensor reset procedure by holding the chip in reset
during the MAX9271 configuration, removing the long sleep delays and
only wait after the chip exits from reset for 350-500 microseconds
interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout
characterized in the chip manual.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The camera module initialization routine does not check the return
value of a few functions. Fix that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the device is identified the driver currently reports the
names of the chips embedded in the camera module.
Report the name of the camera module itself instead.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the noise immunity threshold at the end of the rdacm20
initialization routine.
The rdacm20 camera module has been so far tested with a startup
delay that allowed the embedded MCU to program the serializer. If
the initialization routine is run before the MCU programs the
serializer and the image sensor and their addresses gets changed
by the rdacm20 driver it is required to manually enable the noise
immunity threshold to make the communication on the control channel
more reliable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no reason to allocate dynamically the 'serializer' field in
the driver structure.
Embed the field and adjust all its users in the driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current RDACM21 initialization routine powers up the OV10640 image
sensor after the OV490 ISP. The ISP is programmed with a firmware loaded
from an embedded serial flash that (most probably) tries to interact and
program also the image sensor connected to the ISP.
As described in commit "media: i2c: rdacm21: Fix OV10640 powerup" the
image sensor powerdown signal is kept high by an internal pull up
resistor and occasionally fails to startup correctly if the powerdown
line is not asserted explicitly. Failures in the OV10640 startup causes
the OV490 firmware to fail to boot correctly resulting in the camera
module initialization to fail consequentially.
Fix this by powering up the OV10640 image sensor before testing the
OV490 firmware boot completion, by splitting the ov10640_initialize()
function in an ov10640_power_up() one and an ov10640_check_id() one.
Also make sure the OV10640 identification procedure gives enough time to
the image sensor to resume after the programming phase performed by the
OV490 firmware by repeating the ID read procedure.
This commit fixes a sporadic start-up error triggered by a failure to
detect the OV490 firmware boot completion:
rdacm21 8-0054: Timeout waiting for firmware boot
[hverkuil: fixed two typos in commit log]
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10640 image sensor powerdown signal is controlled by the first
line of the OV490 GPIO pad #1, but the pad #0 identifier
OV490_GPIO_OUTPUT_VALUE0 was erroneously used. As a result the image
sensor powerdown signal was never asserted but was left floating and
kept high by an internal pull-up resistor, causing sporadic failures
during the image sensor startup phase.
Fix this by using the correct GPIO pad identifier and wait the mandatory
1.5 millisecond delay after the powerup lane is asserted. The reset
delay is not characterized in the chip manual if not as "255 XVCLK +
initialization". Wait for at least 3 milliseconds to guarantee the SCCB
bus is available.
While at it also fix the reset sequence, as the reset line was released
before the powerdown one, and the line was not cycled.
This commit fixes a sporadic start-up error triggered by a failure to
read the OV10640 chip ID:
rdacm21 8-0054: OV10640 ID mismatch: (0x01)
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a delay after the OV490 chip is put in reset state. The reset
signal shall be held low for at least 250 useconds.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9271 chip manual prescribes a delay of 5 milliseconds
after the chip exits from low power state.
Add a new function to the max9271 library driver that wakes up the chip
with a dummy i2c transaction and implements the correct delay of 5
milliseconds after the chip exits from low power state.
Use the newly introduced function in the rdacm20 and rdacm21 camera
drivers. The former was not respecting the required delay while the
latter was waiting for a too-short timeout.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of the max9271_write() function in the
max9271 library driver.
While at it, modify an existing condition to be made identical
to other checks.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rephrase a comment in .bound() callback to make it clear we register
a subdev notifier and remove a redundant comment about disabling i2c
auto-ack.
No functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide a macro to define the reverse channel amplitude to
be used to compensate the remote serializer noise immunity.
While at it, update a comment.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cache the current channel amplitude in a driver variable
to skip updating it if the newly requested value is the same
as the currently configured one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the reverse_channel_mv variable to init_rev_chan_mv as
the next patch will cache the reverse channel amplitude in
a new driver variable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to use & to get the start address of an array.
Fix the size of vga_edid.edid to a single block (128 bytes) to fix
this smatch error:
adv7842.c:2538 adv7842_set_edid() error: memcpy() '&state->vga_edid.edid' too small (128 vs 512)
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes: c3fda7f835 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 2561482468 ("[media] tc358743: support probe from device tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The adv7842 driver didn't support EDIDs of 3 or 4 blocks, even though the
hardware supports this.
It is a bit more complicated due to the fact that the adv7842 can expose
two EDIDs: one digital, one analog, for DVI-I connectors. In that case the
VGA_EDID_ENABLE bit is set and blocks 0 and 1 of the EDID eeprom are used
for the DVI-D part and block 2 is used for the DVI-A part of the DVI-I
connector.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 0 here and printing -ENODEV wouldn't be really
helpful. So remove it from the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 0 here and printing -ENODEV wouldn't be really
helpful. So remove it from the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2 sub-device driver for the Sony IMX208 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
[Sakari Ailus: Rename sensor async register function to make it compile,
use exposure_max and wrap a few long lines.]
Signed-off-by: Ping-Chung Chen <ping-chung.chen@intel.com>
Signed-off-by: Yeh, Andy <andy.yeh@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The check on mode_index is sufficient to ensure that we have a
valid mode. Remove the explicit mode check similarly to
commit 38a5023029 ("media: i2c: ov5648: remove unnecessary NULL check")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV8856 sensor can output frames with 2/4 CSI2 data lanes.
This commit adds support for 2 lane mode in addition to the 4 lane
and also configuring the data lane settings in the driver based on
system configuration.
- Fix Bayer order output in 1640x1232 binning registers
- supported data lanes
+ 3280x2464 on 2 & 4 lanes
+ 1640x1232 on 2 & 4 lanes
+ 3264x2448 on 4 lanes
+ 1632x1224 on 4 lanes
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Acked-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some platform(imx6q), xvclk might not switch on in advance,
also for power save purpose, xvclk should not be always on.
so, add clk_prepare_enable(), clk_disable_unprepare() in driver
side to set xvclk on/off at proper stage.
Add following changes:
- add 'struct clk *clk;' in 'struct ov2659 {}'
- enable xvclk in ov2659_power_on()
- disable xvclk in ov2659_power_off()
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to the CCS spec the op_pll_multiplier address is 0x030e,
not 0x031e.
Signed-off-by: Bernhard Wimmer <be.wimm@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: 6493c4b777 ("media: smiapp: Import CCS definitions")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2 async framework is generally used with the V4L2 fwnode, which
also depends on the former. There are a few exceptions but they are
relatively few.
At the same time there is a vast number of systems that need videodev
module, but have no use for v4l2-async that's now part of videodev.
In order to improve, split the v4l2-async into its own module. Selecting
V4L2_FWNODE also selects V4L2_ASYNC.
This also moves the initialisation of the debufs entries for async subdevs
to loading of the v4l2-async module. The directory is named as
"v4l2-async".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'ret' is known to be 1 here. In fact 'i' is expected instead.
Store the return value of 'i2c_master_recv()' in 'ret' so that the error
message print the correct error code.
Fixes: acaa34bf06 ("media: rc: implement zilog transmitter")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822 ("[media] V4L: Add S5C73M3 camera driver")
Fixes: 8b99312b72 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor")
Fixes: 7d459937dc ("[media] Add driver for Samsung S5K5BAF camera sensor")
Fixes: bfa8dd3a05 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PM runtime get logic is currently broken, as it checks if
ret is zero instead of checking if it is an error code,
as reported by Dan Carpenter.
While here, use the pm_runtime_resume_and_get() as added by:
commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors. As a bonus, such function
always return zero on success.
It should also be noticed that a fail of pm_runtime_get_sync() would
potentially result in a spurious runtime_suspend(), instead of
using pm_runtime_put_noidle().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
There is a bug at ccs_pm_get_init(): when this function returns
an error, the stream is not started, and RPM usage_count
should not be incremented. However, if the calls to
v4l2_ctrl_handler_setup() return errors, it will be kept
incremented.
At ccs_suspend() the best is to replace it by the new
pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter automatically,
in the case of errors.
Fixes: 96e3a6b92f ("media: smiapp: Avoid maintaining power state information")
Cc: stable@vger.kernel.org
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If pm_runtime resume logic fails, return the error code
provided by it, instead of -EAGAIN, as, depending on what
caused it to fail, it may not be something that would be
recovered.
Fixes: cbba45d436 ("[media] smiapp: Use runtime PM")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for EDIDs consisting of one EDID block.
Related to this, improve CEC physical address handling.
Clearing the EDID caused a bug since v4l2_calc_aspect_ratio() was
called with a NULL pointer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Only the first pad was configured, but there are 4. This causes
set_fmt to fail with -EINVAL since the passed pad is > 0.
Configure all three sink pads and the source pad.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sparse reports a warning on a cast to u8 of a 16 bits constant.
drivers/media/i2c/rdacm21.c:348:62: warning: cast truncates bits
from constant value (300a becomes a)
Even if the behaviour is intended, silence the sparse warning replacing
the cast with a bitwise & operation.
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the EDID has an odd number of blocks (usually just 1, but the
same problem occurs with 3 blocks), then VIDIOC_G_EDID reported 2
(or 4) blocks. Fix this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While the adv7604/11/12 hardware supported EDIDs up to 4 blocks, the
driver didn't. This patch adds support for this. It also improves support
for EDIDs that do not have a Source Physical Address: in that case the
spa location is set to the first byte of the second block, and the
'physical address' is just the two bytes at that location. This is per
the suggestion in the adv76xx documentation for such EDIDs.
Tested with an adv7604 and adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For the adv7604 the hotplug detect pin is controlled through gpio pins from
the SoC, but the adv7611 and adv7612 control the hotplug detect pin
themselves.
But the driver had no support for this, so the HPD was always high, even
when changing the EDID. Add proper support for this to the driver.
Tested with an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 supports High Dynamic Range with 5 levels of low/high
exposure ratio. Add a V4L2 control for HDR (WIDE_DYNAMIC_RANGE).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move incrementing/decrementing runtime PM count to
imx219_start_streaming()/imx219_stop_streaming() functions respectively.
This fixes an issue of unbalanced runtime PM count in resume callback
error path where streaming is stopped and runtime PM count is left
unbalanced.
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move out locking/unlocking of vflip and hflip controls from
imx219_set_stream() to the imx219_start_streaming()/
imx219_stop_streaming() respectively.
This fixes an issue in resume callback error path where streaming is
stopped and the controls are left in locked state.
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the long names present in V4L2 fwnode and async frameworks shorter.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccicheck warning:
./drivers/media/i2c/ov8865.c:2527:5-8: Unneeded variable: "ret". Return
"0" on line 2536
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix these kernel-doc warnings:
drivers/media/i2c/ccs/ccs-data.h:144: warning: expecting prototype for struct ccs_pdaf_pix_loc_block_desc. Prototype was for struct
ccs_pdaf_pix_loc_pixel_desc instead
drivers/media/i2c/ccs/ccs-quirk.h:51: warning: Function parameter or member 'post_streamoff' not described in 'ccs_quirk'
drivers/media/i2c/ccs/ccs-quirk.h:51: warning: Function parameter or member 'flags' not described in 'ccs_quirk'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When __v4l2_ctrl_modify_range() fails, no error return code of
imx274_s_frame_interval() is assigned.
To fix this bug, ret is assigned with the return valye of
__v4l2_ctrl_modify_range(), and then ret is checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix sub-device function for the pixel array and the scaler.
It seems that the pixel array had gotten assigned as SCALER whereas the
scaler had CAM_SENSOR function. Fix this by setting the pixel array
function to CAM_SENSOR and that of scaler to SCALER.
Fixes: 9ec2ac9bd0 ("media: ccs: Give all subdevs a function")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The macro use will already have a semicolon.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eliminate the following coccicheck warning:
./drivers/media/i2c/ov02a10.c:703:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The adv7604 refused to accept an one-block EDID, it required two blocks.
Fix this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The version here is identical to the one in the I2C core, so use the
latter version directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes these kernel-doc warnings:
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI4A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2A_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2B_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2C_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2A_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2B_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2C_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_INVALID' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_10BIT_422_EMBEDDED_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_20BIT_422_SEPERATE_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_10BIT_422_SEPERATE_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_INVALID' not described in enum 'tvp514x_output'
include/media/i2c/adv7343.h:38: warning: cannot understand function prototype: 'struct adv7343_power_mode '
include/media/i2c/s5k4ecgx.h:31: warning: expecting prototype for struct ss5k4ecgx_platform_data. Prototype was for struct
s5k4ecgx_platform_data instead
include/media/i2c/mt9t112.h:21: warning: cannot understand function prototype: 'struct mt9t112_platform_data '
include/media/i2c/noon010pc30.h:13: warning: Cannot understand * @clk_rate: the clock frequency in Hz
include/media/i2c/s5k6aa.h:45: warning: Function parameter or member 'bus_type' not described in 's5k6aa_platform_data'
include/media/i2c/tw9910.h:19: warning: cannot understand function prototype: 'enum tw9910_mpout_pin '
include/media/i2c/tw9910.h:36: warning: cannot understand function prototype: 'struct tw9910_video_info '
include/media/i2c/ov772x.h:53: warning: cannot understand function prototype: 'struct ov772x_camera_info '
include/media/i2c/s5c73m3.h:53: warning: Function parameter or member 'bus_type' not described in 's5c73m3_platform_data'
drivers/media/i2c/ccs/ccs-quirk.h:50: warning: Function parameter or member 'post_streamoff' not described in 'ccs_quirk'
drivers/media/i2c/ccs/ccs-quirk.h:50: warning: Function parameter or member 'flags' not described in 'ccs_quirk'
drivers/media/i2c/ccs/ccs-data.h:144: warning: expecting prototype for struct ccs_pdaf_pix_loc_block_desc. Prototype was for struct
ccs_pdaf_pix_loc_pixel_desc instead
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'token' not described in 'tvp514x_reg'
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'reg' not described in 'tvp514x_reg'
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'val' not described in 'tvp514x_reg'
drivers/media/i2c/m5mols/m5mols.h:69: warning: Function parameter or member 'brightness' not described in 'm5mols_exif'
drivers/media/i2c/m5mols/m5mols.h:147: error: Cannot parse struct or union!
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN0' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN1' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN2' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN3' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN4' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN5' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN6' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN7' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_HDMI' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TTL' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TXA' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TXB' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_MAX' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:199: warning: Function parameter or member 'i2c_clients' not described in 'adv748x_state'
drivers/media/i2c/adv748x/adv748x.h:199: warning: Function parameter or member 'regmap' not described in 'adv748x_state'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The open coded version differs from the one in the core in one way: the
buffer will be always copied back, even when the transfer failed. Be
more robust: use the block read from the I2C core and propagate a
potential errno further to the sanity checks.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch fixes the following trivial warnings w.r.t. kernel-doc usage:
drivers/media/common/videobuf2/frame_vector.c:38: warning: Excess function parameter 'gup_flags' description in 'get_vaddr_frames'
drivers/media/dvb-core/dvb_ca_en50221.c:193: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1014: warning: expecting prototype for Wake up the DVB CA thread(). Prototype was for
dvb_ca_en50221_thread_wakeup() instead
drivers/media/dvb-core/dvb_ca_en50221.c:1023: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1081: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1112: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1327: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1411: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1426: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1582: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1693: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1743: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1772: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1830: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1922: warning: wrong kernel-doc identifier on line:
drivers/media/rc/img-ir/img-ir-hw.c:628: warning: expecting prototype for img_ir_decoder_compatable(). Prototype was for
img_ir_decoder_compatible() instead
drivers/media/v4l2-core/v4l2-jpeg.c:461: warning: expecting prototype for jpeg_parse_header(). Prototype was for v4l2_jpeg_parse_header()
instead
drivers/media/platform/vsp1/vsp1_dl.c:166: warning: expecting prototype for struct vsp1_cmd_pool. Prototype was for struct vsp1_dl_cmd_pool
instead
drivers/media/platform/mtk-vpu/mtk_vpu.c:28: warning: expecting prototype for is a tiny processor controlling video hardware(). Prototype
was for INIT_TIMEOUT_MS() instead
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:73: warning: expecting prototype for struct vp9_fb_info. Prototype was for struct
vp9_ref_buf instead
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:85: warning: expecting prototype for struct vp9_fb_info. Prototype was for struct
vp9_sf_ref_fb instead
drivers/media/tuners/mt2063.c:1404: warning: expecting prototype for fLO_FractionalTerm(). Prototype was for MT2063_fLO_FractionalTerm() instead
drivers/media/tuners/mt2063.c:1465: warning: expecting prototype for CalcLO2Mult(). Prototype was for MT2063_CalcLO2Mult() instead
drivers/media/usb/pwc/pwc-dec23.c:640: warning: wrong kernel-doc identifier on line:
drivers/media/platform/exynos4-is/media-dev.c:820: warning: expecting prototype for __fimc_md_create_fimc_links(). Prototype was for
__fimc_md_create_fimc_sink_links() instead
drivers/media/i2c/s5k6aa.c:426: warning: expecting prototype for s5k6aa_configure_pixel_clock(). Prototype was for
s5k6aa_configure_pixel_clocks() instead
drivers/media/i2c/imx274.c:700: warning: wrong kernel-doc identifier on line:
drivers/media/i2c/imx274.c:735: warning: wrong kernel-doc identifier on line:
drivers/media/i2c/imx274.c:983: warning: wrong kernel-doc identifier on line:
Most are missing or mistyped function names.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 7f03d9fefc ("media: i2c: Kconfig: Make MAX9271
a module") the max9271 library is built as a module but no
MODULE_*() attributes were specified, causing a build error
due to missing license information.
ERROR: modpost: missing MODULE_LICENSE() in drivers/media/i2c/max9271.o
Fix this by adding MODULE attributes to the driver.
Fixes: 7f03d9fefc ("media: i2c: Kconfig: Make MAX9271 a module")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the introduction of the RDACM21 camera module support in commit
a59f853b3b ("media: i2c: Add driver for RDACM21 camera module") the
symbols defined by the max9271 library were exported twice if multiple
users of the library were compiled in at the same time.
In example:
WARNING: modpost: drivers/media/i2c/rdacm21-camera_module:
'max9271_set_serial_link' exported twice. Previous export was in
drivers/media/i2c/rdacm20-camera_module.ko
Fix this by making the max9271 file a module and have the driver
using its functions select it.
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix this compiler warning:
drivers/media/i2c/imx334.c: In function 'imx334_parse_hw_config':
include/linux/dev_printk.h:112:2: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
112 | _dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~
drivers/media/i2c/imx334.c:783:6: note: 'ret' was declared here
783 | int ret;
| ^~~
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the Sony imx334 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 3840x2160 @ 60fps
- supported bayer order output:
- SRGGB12
Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Reviewed-by: Gjorgji Rosikopulos <gjorgjix.rosikopulos@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The previously added modes 3264x2448 & 1632x1224 are actually
configuring the sensor for BGGR mode, this is an issue since
the mode that is exposed through V4L incorrectly is set as GRBG.
This patch fixes the issue by moving the output crop window of
internal sensor ISP uses by one row, which means that the Bayer
pattern of the output is changed.
row 1: B G B G B G ...
row 2: G R G R G R ...
row 3: B G B G B G ...
...
row 2: G R G R G R ...
row 3: B G B G B G ...
...
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Suggested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This control is needed for imx219 driver, as the link frequency
is independent from the pixel rate in this case, and can't be
calculated from the pixel rate.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set/clear the bits to configure the register to expected value
to assume the v/hflip state.
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ce548396a4 ("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
removed the last in-tree user of this sensor. New users
will be required to use the generic clock framework,
so it's possible to convert the driver to use it.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This sensor driver has a proper device-tree binding, and also
all its platform-data based in-tree users have been converted to use
the generic clock framework.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 63839882c5 ("media: mach-pxa: palmz72/pcm990: remove soc_camera dependencies")
removed the last in-tree user of this sensor. New users
will be required to use the generic clock framework,
so it's possible to convert the driver to use it.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 sensor driver checked in device properties for a
clock-frequency property which actually does not mean that the clock is
really running such frequency or is it even enabled.
Get the provided clock and check it frequency. If none is provided,
fall back to old property.
Enable the clock when accessing the IMX258 registers and when streaming
starts with runtime PM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 can be used also on embedded designs using device tree so
allow the sensor to bind to a device tree node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of rdacm20_video_ops is to assign it to the video field
in the v4l2_subdev_ops struct which is a pointer to const, and the only
usage of rdacm20_subdev_ops is to pass its address to
v4l2_i2c_subdev_init() which accepts a pointer to const. Make them const
to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adjust the initial reverse channel amplitude parsing from
firmware interface the 'maxim,reverse-channel-microvolt'
property.
This change is required for both rdacm20 and rdacm21 camera
modules to be correctly probed when used in combination with
the max9286 deserializer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instrument the function that configures the reverse channel with a
programmable amplitude value.
This change serves to prepare to adjust the reverse channel amplitude
depending on the remote end high-threshold configuration.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break out the reverse channel setup configuration procedure to its own
function.
This change prepares for configuring the reverse channel conditionally
to the remote side high threshold configuration.
No functional changes intended.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesasa@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The RDACM21 is a GMSL camera supporting 1280x1080 resolution images
developed by IMI based on an Omnivision OV10640 sensor, an Omnivision
OV490 ISP and a Maxim MAX9271 GMSL serializer.
The driver uses the max9271 library module, to maximize code reuse with
other camera module drivers using the same serializer, such as rdacm20.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The "mode_index == ARRAY_SIZE(ov5648_modes)" check ensures that we
exited the loop via a break statement so we know that "mode" must
be valid. Delete this unnecessary NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
By adding this cast '(__force __le16)' this sparse warning
is fixed:
drivers/media/i2c/ov02a10.c:391:19: warning: cast to restricted __le16
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix two typos: dvdd -> dovdd and dvdd -> avdd
Both clearly copy-and-paste mistakes.
Fixes this smatch warning:
drivers/media/i2c/ov8865.c:2852 ov8865_probe() warn: passing zero to 'PTR_ERR'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This solves a few minor cosmetic issues picked up by checkpatch for
the OV5648 and OV8865 drivers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
GCC with W=2 level of kernel compiler warnings warns about the use of
uninitialised variables in a few locations. While these uninitialised
variables were not used in reality, this still produced compiler warnings.
Address this by assigning the variables to NULL and checking for NULL in
places it is not expected, returning -EIO in that case. This provides
at least some sanity checking at runtime as the compiler appears unable to
do that at compile time.
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
struct device is used in ccs-data.h but no definition is included. Add a
forward definition.
Also ccs-data.c includes linux/types.h but this is already included in
ccs-data.h which ccs-data.c includes. Do don't include linux/types.h in
ccs-data.c.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit b3c0115e34.
As per Documentation/process/license-rules.rst "GPL v2" exists only for
historical reasons and has the same meaning as "GPL". So revert this
patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The preferred integer types in the kernel are the Linux specific ones,
switch from standard C types to u32 and alike.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The preferred integer types in the kernel are the Linux specific ones,
switch from standard C types to u32 and alike.
The patch has been produced with the following Coccinelle spatch, with few
alignment adjustments:
@@
typedef uint32_t;
typedef u32;
@@
- uint32_t
+ u32
@@
typedef uint16_t;
typedef u16;
@@
- uint16_t
+ u16
@@
typedef uint8_t;
typedef u8;
@@
- uint8_t
+ u8
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS supports three variants of PHY timing control, auto, UI based and
manual. The driver previously assumed UI based control that requires
updating the link rate to the sensor. Now default to automatic control
instead, and only write the link rate to the sensor in UI mode.
If neither auto or UI control is supported, return an error in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver depends on the external clock frequency. Add a sanity check for
the frequency, by returning an error from probe if it's zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A CCS compliant device requires a delay before the first I²C transaction
after pulling xshutdown up or starting the external clock. This is what
the driver does. However, if neither is actually there, there's no need
for the delay.
This also has the effect of removing an unnecessary delay on ACPI systems
where ACPI is responsible for the power-up sequence.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Verify the software reset has been completed until proceeding.
The spec does not guarantee a delay but presumably 100 ms should be
enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver always used software reset after the sensor's power sequence
that includes a hardware reset if we have a reset GPIO. Do not use
software reset if we just brought the sensor up from hardware reset state.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor's address was changed before resetting and changing the
address again. Don't do it before reset as it's useless.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Get the first endpoint from port 0 instead of the next one, whatever it
might be. There are no other ports so there's no functional change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Also print out MSR registers written to the sensor. This isn't entirely
optimal as the debug strings are produced even if they're not used but
that isn't really a grave issue --- the I²C bus is very slow anyway.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS spec defines an alternative implementation for global analogue
gain. Add support for that in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add four controls for reading CCS analogue gain coefficients. The
values are constants that are device specific.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some devices do not implement analogue gain this way. Only add the control
when a device does have the support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The analogue gain control was stored to the device specific struct but was
never used. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SMIA only has per-component digital gain. Add support for it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS supports global (all-component) digital gain. Add support for it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drivers don't need to explicitly call devm_{}_put on driver
removal, as it's automatically called by the device driver
resource management code.
Fixes: aab7ed1c39 ("media: i2c: Add driver for Aptina MT9V111")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV8865 is a 8 Mpx CMOS image sensor producing 3264x2448 at 30 fps.
Other modes (including some with sub-sampling) are available too.
It outputs 10-bit bayer CFA data through a MIPI CSI-2 interface with
up to 4 lanes supported.
Some register initialisation sequences are still needed for this driver,
as they cover registers for which no documentation is available.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version is a rewrite of the first version that matches the structure
of the OV5648 driver, with explicit PLL configuration, all the necessary
mode-specific fields, associatied registers and reduced static sequences.
It was tested with the Banana Pi Camera Board v3 and the Banana Pi M3.
Co-developed-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5648 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2
in a one or two lane configuration.
Most of the features of the hardware are supported, including:
- Auto and manual exposition/gain
- Auto and manual white balance
- Horizontal and vertical flip
- Test patterns
But the following are still missing:
- Debanding, based on power source frequency;
- Exposition setting correlated to time units.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver currently reports a single supported value for
V4L2_CID_PIXEL_RATE and initializes the control's minimum value to 0,
which is very risky, as userspace might accidentally use it as divider
when calculating the time duration of a line.
Fix this by using as minimum the only supported value when registering
the control.
Fixes: 5de35c9b8d ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Capturing in 640x480 SBGGR8_1X8 hangs the system when capturing
with the unicam driver on RaspberryPi 4 platform.
Remove it and remove the support for multiple media bus codes in
the driver.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver reports the V4L2_SUBDEV_FL_HAS_EVENTS flag but does not
support subscribing and unsubscribing to events.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the two register-value lists const.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use pm_runtime_get_if_in_use() in s_ctrl to apply controls
only when the device is powered on.
Rework the control set function to balance the
pm_runtime_get_if_in_use() call with
pm_runtime_put() at the end of the function.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the s_stream() operation to turn the sensor on and
off at stream enable/disable time using the pm_runtime infrastructure.
Protect the stream on/off from being called multiple times in
sequence with a 'streaming' flag.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the pm_runtime framework to replace the legacy s_power() operation.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure is clipped by the VTS of the mode, so it needs to be updated
when this is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the V4L2_CID_HBLANK read-only control.
The implementation has been upported from RaspberryPi BSP commit:
commit d82f202156605 ("media: i2c: ov5647: Set V4L2_SUBDEV_FL_HAS_EVENTS flag")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clients need to know the pixel rate in order to compute exposure
and frame rate values. Advertise it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov5647 subdev can generate control events, therefore set
the V4L2_SUBDEV_FL_HAS_EVENTS flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that the driver supports more than a single mode, implement the
.set_fmt pad operation and adjust the existing .get_fmt one to report
the currently applied format.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SBGGR10_1X10 formats support more resolutions than SBGGR8_1X8.
Make it the default sensor format and set 2x2 binned 640x480 resolution
as default sensor size as it maximizes the FOV and framerate.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Before adding new modes, rename the only existing one to report
the bit depth to distinguish it from future additions.
While at it, briefly describe the mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support the get_selection() pad operation to report the device
full pixel array size, the currently applied analogue crop rectangle and
the active pixel array dimensions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break format handling out from the main driver structure.
This commit prepares for the introduction of more sensor formats and
resolutions by instrumenting the existing operation to work on multiple
modes instead of assuming a single supported one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver structure name is referred to with different names ('ov5647',
'state', 'sensor') in different functions in the driver.
Polish this up by using 'struct ov5647 *sensor' everywhere.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add controls to support AWB, AEC and AGC. Also add control support to
set exposure (in lines) and analogue gain (as a register code).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the driver mutex to protect s_stream() operations.
This will become more relevant once the sensor will support more formats
and set_format() could be issue concurrently to s_stream().
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the .enum_frame_size subdev pad operation.
As the driver only supports one format and one resolution at the moment
the implementation is trivial.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename __sensor_init() function to ov5647_set_mode() as the function
is a regular one and the double underscores prefix shall be removed, and
then move it to program the mode at s_stream(1) time, not at sensor power
up.
Break out from __sensor_init() the stream_off() operation call at sensor
power up to coax the lanes in LP-11 state.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov5647_read()/ov5647_write() return in case of success the number
of bytes read or written respectively. This requires callers to check
if the return value is less than zero to detect an error. Unfortunately,
in several places, callers directly return the result of a read/write
call, causing issues when the returned valued is checked to be different
from zero to detect an error.
Fix this by returning zero if i2c_master_send() and i2c_master_read()
return a positive value (the number of bytes written or read).
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the boilerplate license text with the SPDX identifier.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver has some obvious style issues which are worth fixing before
expanding the driver capabilities.
Fix:
- Variable declaration order
- Function parameters alignment
- Multi-line comments and spurious line breaks
- Use lowercase for hexadecimal values
- > 80 cols lines
Cosmetic change, no functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver currently support a single format. Fix its initialization to
use the only supported resolution.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no way to query the subdevice for the supported
resolutions. Add set_fmt and get_fmt implementations. Since there's
only one format supported set_fmt does nothing and get returns single
format.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for optional non-continuous clock mode to the ov5647
sensor driver.
Non-continuous clock saves a small amount of power and on some SoCs
is easier to interface with.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for an optional GPIO connected to PWDN on the sensor. This
allows the use of hardware standby mode where internal device clock
and circuit activities are halted.
Please note that power is off when PWDN is high.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix obtaining CCS static data version minor part correctly. Instead, the
upper 8 bits were obtained from the major version number.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The highest fundamental frequency signal for C-PHY is half of the symbol
rate which is similar to D-PHY. Take this into account in ccs-pll.
Also remove the outdated comment.
Fixes: 8030aa4f9c ("media: ccs-pll: Add C-PHY support")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Try parsing the firmware also as C-PHY. Do this only after D-PHY as older
firmware may not explicitly specify bus-type in which case D-PHY is the
default.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print pixel rates on CSI-2 bus as well as in pixel array as the variation
allowed in PLL capabilities makes this non-trivial to figure out
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support dual data rate operational system and pixel clocks by conveying
the flags to the PLL calculator and updating how the link rate is
calculated.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for dual data rate operational system and pixel clocks. This
is implemented using two PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that either require dual PLL or support single or
dual PLL but use dual PLL as default.
Use sensor default configuration for sensors that support both modes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that have separate VT and OP domain PLLs.
This support is trivial in the sense that it aims for the same VT pixel
rate than that on the CSI-2 bus. The vast majority of sensors is better
supported by higher frequencies in VT domain in binned and possibly scaled
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Separate VT divisor limit calculation from the rest of the VT PLL branch
calculation. This way it can be used for dual PLL support as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL calculator only searched even total divisor values apart from one,
but this is wrong: the total divisor is odd in cases where system divisor
is one. Fix this by including odd total PLL values where system divisor is
one to the search.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make VT divisors 16-bit unsigned numbers. They don't need 32 bits after
all.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor bounds checks so that the caller can decide what to check. This
allows doing the checks early, when the values are available.
This also adds front OP PLL configuration and limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print information on PLL tree configuration based on the flags. This also
adds support for printing dual PLL trees, and better separates between OP
and VT PLL trees.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Better separate OP PLL branch calculation from VT branch calculation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some sensors support derating (VT domain speed faster than OP) or
overrating (VT domain speed slower than OP). While this was supported for
the driver, the hardware support for the feature was never verified. Do
that now, and for those devices without that support, VT and OP speeds
have to match.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split off the VT sub clock tree calculation from the rest, into its own
function. Also call the op_pll_fr argument pll_fr, since soon these may
not be OP tree values.
This paves way for additional features in the future such as dual PLL
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add C-PHY support for the CCS PLL calculator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add sanity checks for fields that could cause division by zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Flexible OP PLL pixel clock divider allows a higher OP pixel clock than
what the bus can transfer. This generally makes it easier to select pixel
clock dividers.
This changes how the pixel rate on the bus and minimum VT divisor are
calculated, as the pixel rate is no longer directly determined by the
OP pixel clock and the number of the lanes.
Also add a sanity check for sensors that do not support flexible OP PLL
pixel clock divider. This could have caused the PLL calculator to come up
with an invalid configuration for those devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The l parameter defines the number of clock cycles to process a single
pixel per OP lane. It is calculated based on a new register
op_bits_per_lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS allows odd PLL dividers other than 1, granted that the corresponding
capability bit is set. Support this both in the PLL calculator and the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for decoupled OP domain clock calculation. This means that the
number of VT and OP domain clocks are no longer dependent on the number of
CSI-2 lanes in the lane speed mode.
The support also replaces the existing quirk flag to calculate OP domain
clocks per lane.
Also support decoupled OP domain calculation in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Convey the relevant PLL flags to the PLL calculator. Also the lane speed
model affects how the link rate is calculated on the CSI-2 bus, as the
rate is total of all lanes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS PLL includes a capability to calculate the VT clocks on per-lane
basis. Add support for this feature.
Move calculation of the pixel rate on the CSI-2 bus early in the function
as everything needed to calculate it is already available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use uint32_t instead of unsigned int for a variable that contains
explicitly 32-bit numbers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The additional multiplier (for higher VT timing) of the PLL multiplier was
checked against the upper limit but the result was rounded up, possibly
producing too high additional multiplier. Round down instead to keep
within hardware limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The comment is about minimum PLL multiplier but the related check really
deals with the maximum PLL multiplier.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The external clock frequency times the PLL multiplier may exceed the value
range of 32-bit unsigned integers. Instead perform the same calculation y
using two divisions.
The result has some potential to be different, but that's ok: this number
is used to limit the range of pre-PLL divisors to find optimal values. So
the effect of the rare case of a different result here would mean an
invalid pre-PLL divisor is tried. That will be found out a little later in
any case.
Also guard against dividing by zero if the external clock frequency is
higher than the maximum OP PLL output clock --- a rather improbable case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The lower bound of the pre-PLL divider was calculated based on OP SYS
clock frequency which is also affected by the OP SYS clock divider. This
is wrong. The right clock frequency is that of the PLL output clock.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OP system clock frequency defines the CSI-2 bus clock frequency, not
the PLL output clock frequency. Both values were overwritten in the end,
but the wrong limit value was used for the OP system clock frequency,
possibly leading to too high frequencies being used.
Also remove now duplicated calculation of OP system clock frequency later
in the PLL calculator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the BIT macro for setting individual bits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS pll is used by the CCS driver at the moment, but documenting the
interface makes sense. It's non-trivial and the calculator could be used
elsewhere.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This way the struct will use less memory, with better packing and no waste
due to unsigned long.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Differentiate between CSI-2 D-PHY and C-PHY. This does not yet include
support for C-PHY.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The parallel bus PLL calculation has no users. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VT divisor search can be ended if we've already found the value that
corresponds exactly the total divisor, as there are no better (lower)
values available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the correct video timing divisor to calculate the SYS divisor. Instead
of the current value, the minimum was used. This could have resulted in a
too low SYS divisor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS spec supports a lot of variation in the PLL. Split the PLL in
front and back parts to better prepare for supporting it.
Also use CCS compliant naming for IP and OP PLL frequencies (i.e. include
"clk" in the name).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pll->pll_op_clk_freq is a 32-bit number. It does not need div_u64 to
divide it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
rval wasn't set, resulting in probe returning zero instead of an error.
Fixes: de10c1619c ("[media] smiapp: Get clock rate if it's not available through DT")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no intialization for the 'reg' variable, so printing
it produces undefined behavior as well as a compile-time warning:
drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized]
"0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg,
Remove the variable and stop printing it.
Fixes: fd9065812c ("media: smiapp: Obtain frame descriptor from CCS limits")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clang points out that the error handling in ov02a10_s_stream() is
broken, and just returns a random error code:
drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If streaming is already on, leave it that way and return success.
Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Fixes: 91807efbe8 ("media: i2c: add OV02A10 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use regulators vio and vcore besides vana. The regulators were always
there but on many boards they've been hard wired. Control them explicitly
now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SMIA nor CCS need these delays; remove them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Longer idle period is required on I²C bus before the first transaction
after lifting xshutdown.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Over the years (and renaming) some lines that may well be wrapped ended up
being over 80 characters, likewise there are shorter lines that can be
merged. Do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If pm_runtime_get_sync() fails, there's no need to set the device active
again. Also, in the same case to return the usage_count to zero,
pm_runtime_put_noidle() is enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Write manufacturer specific registers (MSRs) from file to the sensor on
sensor power-on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the delay between I²C access retries a range between 1 and 2 ms. Also
make the number of retries 10 instead of 5, in order not to reduce the
total amount of time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
